LG | L1713P | LG L1713P Owner’s Manual

User's Guide
L1713P
L1913P
Make
sure
to read the
Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached
dealer when you
on
the back cover and quote this information to your
require service.
Precautions
Important
This unit has been
engineered and manufactured to ensure your personal
safety, however improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
On
Safety
power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
Use
only the
manufacturer
or
the nearest authorized
repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords
cords and broken
plugs. They
technician for replacement.
Do not
Open
There
the
may result in
are
a
dangerous. So
shock
or
are
frayed
power
fire hazard. Call your service
Display.
serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
are no user
To Avoid Personal
Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire
or
Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
A1
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not
the display where the power cord is subject to damage.
Do not
use
this
display
sink, laundry tub, in
near water
a wet
such
basement,
as near a
or near a
place
bathtub, washbowl, kitchen
swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
can cause
strike the Active Matrix LCD with anything hard
damage the Active Matrix LCD permanently.
Do not rub
mar, or
or
Do not press the LCD
some
screen
with your
finger for a long
time
as
as
this may scratch,
this may
cause
afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If
possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On
Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly
screen because over-spraying may cause electrical shock.
On
on
the
display
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On
Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
the
Connecting
Before
Display
setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Connecting the stand
base
or
Removing the stand
base
1. Place the monitor with its front facing downward on a cushion or soft cloth.
2. Align the hooks on the stand base with the matching slots in the base of
the monitor.
3.
Insert the hooks into slots.
Warning:
The tape and locking pin may only be removed from those monitors
equipped with a standing base when the base is pulled up.
Therwise, you may be injured by the protruding sections of the stand.
Hook
Slot
4.
Use
a
coin
on
the back of the stand base and turn the
screw
clockwise to
tighten.
5.
When you desire to disintegrate the monitor from the stand base,
coin to turn the screw counterclockwise.
use a
Screw
100
100
Important
This illustration
the items
depicts the general
shown in the picture.
model of connection. Your monitor may differ from
Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only the stand base. The
fall and get
damaged
or
injure your foot.
A3
product
may
the
Connecting
Before
Display
setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Positioning your display
Adjust the position of the panel
Tilt
in various ways for maximum comfort.
Range : -5˚~20˚
Height Range
:
Swivel :350˚
maximun 3.15 inch (80.0mm)
80.0mm
First, remove
the locking
pin.
Landscape
& Portrait : You
can rotate
(* For detailed information, please refer
*
Make
sure
the
panel 90o clockwise.
to the Pivot Sofeware CD
provided.)
not to touch the
floor when the head rotates
to
use
the Pivot function.
Ergonomic
ergonomic and comfortable viewing
monitor should not exceed 5 degrees.
It is recommended that in order to maintain
position,
the forward tilt
angle of the
an
A4
Connecting
the
Display
Using the Computer
1.
2.
Place the monitor in
convenient, well-ventilated location near your computer.
To adjust height of your monitor, unlock the stand lock on top of the stand.
Connect the signal cable. When attached, tighten the thumbscrews to secure
a
the connection.
3. Connect the power cord into a proper power outlet
that is
easily accessible and close to the display.
Signal Cable
Power Cord
Digital signal
-
DVI*
*
NOTE
This is
D-sub*
Varies according to model.
simplified
representation of the rear view.
This
Analog signal
a
Wall-outlet
view
represents a
general model; your display
rear
type*
2
Mac adapter
may differ from the view as
shown.
For Apple Macintosh use,
1
separate plug adapter is
needed to change the
15 pin high density (3 row)
a
PC-outlet
type*
D-sub VGA connector on
thesupplied cable to a 15 pin
2 row connector.
PC
MAC
4.
Press
power
Image
button
on
the front switch
panel
to turn the
When monitor power is turned on, the 'Self
Setting Function' is executed automatically.
on.
NOTE
'
Self
Function'? This function
provides the user with optimal display settings.When the user
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for
individual input signals. If you want to adjust the monitor while in use, or wish to manually run this function once
again, push the 'AUTO' button on the front panel of the monitor. Otherwise, you may execute the Factory reset'
option on the OSD adjustment menu. However, be aware that this option initializes all the menu items except
'Language'.
Image Setting
'
A5
Control Panel Functions
Front Panel Controls
LightView
Control
Function
Power Button
Use this button to turn the
Power
This Indicator
(DPMS)
display
on or
off.
Indicator
lights up green when the display
operates normally. If the display is in DPM (Energy
Saving) mode, this indicator color changes to amber.
MENU Button
Use this button to enter
or
exit the On Screen
Display.
Buttons
Use these buttons to choose
the On Screen
adjust
items in
Display.
AUTO/SELECT
Use this button to enter
Button
Display.
A6
or
a
selection in the On Screen
Control Panel Functions
Control
Direct Access Function
This feature lets you easily select the best desired image condition
optimized to the environment (ambient illumination, image types etc.).
?
DAY
?
NIGHT : Dark ambient illumination
?
?
?
?
:
Bright ambient illumination
TEXT : For text images
(Word processing etc.)
MOVIE : For animation images in videos or movies
PHOTO : For pictures or drawings
USER MODE : For use under user setup image conditions
(Brightness, contrast and color tint are selected by the user in
OSD Screen Setup Menu.)
100
Bring
100
up Contrast and
Brightness adjustment.
:˛
AUTO IMAGE ADJUSTMENT
When
your display settings, always press the
AUTO/SELECT button before entering the On Screen
adjusting
Display(OSD). This will automatically adjust your display image
to the ideal settings for the current screen resolution size
(display mode).
The best
display
mode is 1280x1024.
SOURCE
Use this button to make Dsub
or
DVI connector active. This
feature is used when two computers
display. The default setting is Dsub.
are
connected to the
CONTROLS LOCKED/UNLOCKED
:
MENU and
This function allows you to secure the current control settings,
so that they cannot be inadvertently changed. Press and hold
the MENU button and
button for 3 seconds: the message
"CONTROLS LOCKED" appears.
You
unlock the OSD controls at any time
MENU button and
button for 3 seconds:
can
by pushing
the message "CONTROLS UNLOCKED" will appear.
A7
the
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the
To make
display to
stabilize for at least 30 minutes before
adjustments
in the On Screen
Display, follow these steps:
Press the MENU Button, then the main
To
access a
becomes
control,
highlighted,
Use the
menu
of the OSD appears.
Buttons. When the icon you want
press the AUTO/ SELECT Button.
use
the
making image adjustments.
or
Buttons to
adjust the item
to the desired level.
Accept the changes by pressing the AUTO/SELECT Button.
Exit the OSD
by Pressing the MENU Button.
A8
On Screen
Display(OSD)
Selection and
Adjustment
following table indicates all the On Screen Display control, adjustment,
and setting menus.
The
Main
menu
BRIGHTNESS
CONTRAST
COLOR
Sub
A
menu
D
Reference
BRIGHTNESS
To
and
contrast of the screen
CONTRAST
PRESET
adjust the brightness
9300K
To customize the color of the
6500K
screen
R/G/B(User Color)
GAMMA
POSITION
TRACKING
SETUP
V POSITION
To
H POSITION
screen
CLOCK
adjust the position
To
PHASE
improve the clarity
stability of the screen
LANGUAGE
To customize the
OSD POSITION
for
a
user's
operating
FACTORY RESET
WHITE BALANCE
A
:
D
:
Adjustable
Analog Input
Digital Input
NOTE
The order of icons may differ
depending
on
A9
and
screen
SIGNAL
:
of the
the model (A9~A11).
status
environment
On Screen
Display(OSD)
Selection and
Adjustment
procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
You
were
introduced to the
NOTE
OSD (On Screen
To
Display)
menu
languages
adjust the brightness and
OSD
on
the monitor may differ from the manual.
contrast of the
Adjust
screen
Description
BRIGHTNESS
To
adjust the brightness
of the
screen.
CONTRAST
To
To customize the color of the
OSD
adjust the
contrast of the screen.
screen
Adjust
Description
PRESET
9300K/6500K
Select the
?
9300K:
?
6500K:
color.
screen
Slightly
Slightly
bluish white.
reddish white.
RED
GREEN
Set your
own
color levels.
BLUE
GAMMA
To
adjust the position of the
OSD
Set your own gamma value. (-30~30)
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
screen
Adjust
Description
Vertical Position
To
move
image
up and down.
Horizontal Position
To
A10
move
image left
and
right.
On Screen
To
Display(OSD)
improve
OSD
the
clarity
and
stability
Adjust
To customize the
OSD
Selection and
screen
Adjustment
of the
screen
Description
CLOCK
To minimize any vertical bars or stripes
visible on the screen background.The
horizontal screen size will also change.
PHASE
To adjust the focus of the display. This
item allows you to remove any horizontal
noise and clear or sharpen the image of
characters.
status for
a
user's
Adjust
operating environment
Description
LANGUAGE
To choose the
control names
OSD POSITION
To adjust position of the OSD window
the screen.
SIGNAL
To select DSUB ANALOG, DVI DIGITAL
as the active input. This feature is used
when two computers are connected to the
display. The display automatically detects
the proper input when only one video
source is connected.
FACTORY
Return to all factory default settings
except "LANGUAGE".
If you don't want to reset the monitor, use
the
button to select NO and then
press the AUTO/SELECT button.
RESET
language in which the
are displayed.
on
If the output of the video card is different
the required specifications, the color
WHITE
BALANCE
level may deteriorate due to video
signal distortion. Using this function, the
signal
level is
adjusted
to fit into the
standard output level of the video card
in order to provide the optimal image.
Activate this function when white and
black colors
For
If this does not
are
present in the
screen.
example
improve the screen image, restore the factory default settings. If
necessary, perform the white balance function again. This function will be enabled
only when the input signal is an analog signal.
A11
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
display connected?
Check and
Is the power indicator
light on?
Press the Power button.
Is the power on and the
power indicator green?
Adjust the brightness
Is the power indicator
amber?
If the
properly
the
to
if the power cord is connected
to the power outlet.
see
is in power saving mode, try moving
or pressing any key on the keyboard
display
mouse
bring up the
screen.
if the power is
to turn on the PC.
Make
Try
and the contrast.
sure
on.
Do you see an "INPUT
SIGNAL OUT OF
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
RANGE" message
the screen?
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
on
Doyouseea"NO
SIGNAL "message on
This message appears when the signal cable
between your PC and your display is not
the screen?
connected. Check the
Do you
see a
"CONTROLS LOCKED" message
Do you see
"CONTROLS LOCKED"
when you
button?
signal cable
push
MENU
You
can secure
again.
the screen?
the current control
settings,
inadvertently
they cannot be
changed. You can unlock the OSD controls
at any time by pushing the MENU button
so
that
on
and try
and
button for 3 seconds: the message
"CONTROLS UNLOCKED" will appear.
A12
Troubleshooting
Display image
Display
is incorrect
Position is
incorrect.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position
icon in the on screen display.
Check Control Panel --> Display --> Settings
and see if the frequency or the resolution were
changed. If yes, readjust the video card to the
recommend resolution.
On the
screen
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
The
screen
mono or
color is
abnormal.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make
sure
the video card is
properly
inserted in
the slot.
Set the color
setting higher than 24
color) at Control Panel Settings.
bits
(true
-
The
screen
blinks.
Check if the
screen
is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It
has to be
A13
higher than
AC100-240V 50/60Hz.
Troubleshooting
Have you installed the
driver?
display
Have you installed the
display driver?
display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
driver from our web site: http://www.lge.com.
Do you
Make
see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
Be
sure
to install the
sure
to check if the video card
Plug&Play function.
monitor found"
message?
A14
supports
Specifications
L1713P
17 inches (43.2cm) Flat Panel Active matrix-TFT LCD
Display
Anti-Glare coating
17 inches viewable
0.26mm pixel pitch
Horizontal
Sync Input
Freq.
Analog:30 83kHz (Automatic)
Digital:30 71kHz (Automatic)
-
-
Vertical
Video
Input
Resolution
56
Freq.
75Hz (Automatic)
-
Input Form
Separate TTL, Positive/Negative
Composite TTL, Positive/Negative
SOG (Sync On Green)
Digital
Signal Input
15
pin D-Sub Connector
DVI
-
D connector
Input Form
RGB Analog (0.7Vp-p/75ohm), Digital
Max
DVI
Recommend
VESA 1280
Digital:VESA 1280 x 1024@60Hz
D-sub Analog:VESA 1280 x 1024@75Hz
Plug&Play
DDC 2B
Power
Normal
:
Consumption
Stand-by/Suspend
≤
DPMS Off
≤2W
Dimensions
Width
37.0
&Weight
(with tilt/ swivel
stand)
Height
Range
Depth
Swivel
range
Rotate
Power
Input
Environmental
Conditions
Tilt/Swivel Stand
Signal
cable
Power cord
1024@60Hz
43W
2W
cm
-5˚~20˚
350˚
80.0mm / 3.15 inches
90˚ clockwise (Landscape
Tilt
Height
x
/ 14.57 inches
42.1cm / 16.57 inches (Min)
50.1 cm /19.72 inches (Max)
24.26cm / 9.55 inches
6.0 kg (13.23lbs)
Net
Tilt/Swivel
(Digital)
->
Portrait)
AC 100-240V~50/60Hz 1.0A
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Storage Conditions
Temperature -20˚C to 60 ˚C
5 % to 95 % non-Condensing
Humidity
Attached(
), Detached ( O )
Attached(
), Detached ( O )
Wall-outlet type
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A15
notice.
Specifications
L1913P
19 inches (48.26cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
19 inches viewable
0.294mm
pixel pitch
Horizontal
Sync Input
Freq.
Analog:30 83kHz (Automatic)
Digital:30 71kHz (Automatic)
-
-
Vertical
Video
Input
Resolution
56
Freq.
-
75Hz (Automatic)
Input Form
Separate TTL, Positive/Negative
Composite TTL, Positive/Negative
SOG (Sync On Green)
Digital
Signal Input
15
pin D-Sub Connector
DVI
-
D connector
Input Form
RGB Analog (0.7Vp-p/75ohm), Digital
Max
DVI
Recommend
D-sub Analog:VESA 1280 x 1024@75Hz
VESA 1280 x 1024@60Hz
Digital:VESA
Plug&Play
DDC 2B
Power
Normal
:
Consumption
Stand-by/Suspend
≤
DPMS Off
≤2W
Dimensions
Width
41.28
&Weight
(with tilt/ swivel
stand)
Height
43.57
Tilt/Swivel
Range
51.57
Environmental
Conditions
Tilt/Swivel Stand
Signal
cable
Power cord
45W
2W
/ 16.25 inches
cm / 17.15 inches (Min)
cm / 20.30 inches (Max)
cm / 9.55 inches
(15.87lbs)
cm
24.26
Net
7.2kg
Tilt
-5˚~20˚
350˚
80.0mm / 3.15 inches
90˚ clockwise (Landscape
Swivel
range
Rotate
Input
1280 x 1024@60Hz
Depth
Height
Power
(Digital)
->
Portrait)
AC 100-240V~50/60Hz 1.0A
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Storage Conditions
Temperature -20˚C to 60 ˚C
5 % to 95 % non-Condensing
Humidity
Attached(
), Detached ( O )
Attached(
), Detached ( O )
Wall-outlet type
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A16
notice.
Specifications
Preset Modes
(Resolution)
Display Modes (Resolution)
Horizontal
Freq. (kHz)
Vertical
Freq. (Hz)
VGA
640
x
350
31.469
70
VGA
720
x
400
31.468
70
VGA
640
x
480
31.469
60
VESA
640
x
480
37.500
75
VESA
800
x
600
37.879
60
VESA
800
x
600
46.875
75
MAC
832
x
624
49.725
75
VESA
1024
x
768
48.363
60
VESA
1024
x
768
60.123
75
10
MAC
1152
x
870
68.681
75
11
VESA
1152
x
900
61.805
65
12
VESA
1280
x
1024
63.981
60
13
VESA
1280
x
1024
79.976
75
123456789
Indicator
MODE
LED Color
Normal
green
Stand-by/Suspend
amber
DPMS Off
amber
A17
Specifications
VESA wall
mounting
Connected to another
object (stand type
and wall-
mounted type. This monitor accepts a VESAcompliant mounting interface pad.- optional)
For further
Mounting
information, refer
to the VESA Wall
Instruction Guide.
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased
separately at most
computer
A18
stores
Specifications
Connector Pin
Signal
1
8
917
16
Assignment
24
DVI-D Connector
Pin
Pin
Signal(DVI-D)
Signal(DVI-D)
T. M. D. S. Data2-
16
Hot
T. M. D. S. Data2+
17
T. M. D. S. Data0-
123456789
T. M. D. S. Data2/4 Shield
18
T. M. D. S. Data0+
T. M. D. S. Data4-
19
T. M. D. S. Data0/5 Shield
T. M. D. S. Data4+
20
T. M. D. S. Data5-
DDC Clock
21
T. M. D. S. Data5+
DDC Data
22
T. M. D. S. Clock Shield
23
T. M. D. S. Clock+
24
T. M. D. S. Clock-
Analog
Vertical
Sync.
T. M. D. S. Data1-
10
T. M. D. S. Data1+
11
T. M. D. S. Data1/3 Shield
12
T. M. D. S. Data3-
13
T. M. D. S. Data3+
14
+5V Power
15
Ground (return for +5V,
H. Sync. and V. Sync.)
T. M. D. S.
(Transition
Minimized Differential
A19
Signaling)
Plug
Detect
Digitally yours
Download PDF

advertising