LG | M203WA | LG M203WA Owner’s Manual

Safety Precautions
Please read these safety precautions carefully before using the product.
Warning If you ignore the warning message, you may be seriously injured or there is a possibility of
accident or death.
Caution If you ignore the caution message, you may be slightly injured or the product may be damaged
Precautions in installing the Product
Warning
Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.
Keep the packing anti-moisture material or vinyl packing out of the reach of children.
- Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the
nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.
Do not put heavy objects on the product or sit upon it.
- If the product collapses or is dropped, you may be injured. Children must pay particular attention.
Do not leave the power or signal cable unattended on the pathway.
- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury.
Install the product in a neat and dry place.
- Dust or moisture can cause electrical shock, fire or product damage.
If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the
service center.
- If you continue to use without taking proper measures, electrical shock or fire can occur.
If you dropped the product or the case is broken, turn off the product and unplug the power cord.
- If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service
center.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or inflammable
objects such as paper and matches. Children must pay particular attention.
- Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and
contact the service center.
Caution
Make sure the product ventilation hole is not blocked. Install the product in a suitably wide place (more
than 10cm from the wall)
- If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat.
Do not block the ventilation hole of the product by a tablecloth or curtain.
- The product can be deformed or fire can break out due to overheating inside the product.
Install the product on a flat and stable place that has no risk of dropping the product.
- If the product is dropped, you may be injured or the product may be broken.
Install the product where no EMI occurs.
Keep the product away from direct sunlight.
- The product can be damaged.
A1
Safety Precautions
Electrical Power Related Precautions
Warning
Make sure to connect the power cable to the grounded current.
- You may be electrocuted or injured.
Use the rated voltage only.
- The product can be damaged, or you may be electrocuted.
During a thunder or lightning storm, unplug the power cable or signal cable.
- You may be electrocuted or a fire can break out.
Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet. Use a
power bar with a grounding terminal designed for exclusive use with the computer.
- A fire can break out due to overheating.
Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry
the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
If you don’t intend to use the product for a long time, unplug the power cable from the product.
- Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire.
Fix the power cable completely.
- If the power cable is not fixed completely, a fire can break out.
Hold the plug when pulling out the power cable. Do not bend the power cord with excessive force or put
heavy objects on the power cord.
- The power line can be damaged, which may cause electric shock or fire.
Do not insert a conductor (like a metal chopstick) into one end of the power cable while the other end is
connected to the input terminal on the wall. Additionally, do not touch the power cable right after
plugging into the wall input terminal.
- You may be electrocuted.
The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily
accessible after installation.
Caution
Do not unplug the power cord while the product is in use.
- Electrical shock can damage the product.
Precautions in Moving the Product
Warning
Make sure to turn off the product.
- You may be electrocuted or the product can be damaged.
Make sure to remove all cables before moving the product.
- You may be electrocuted or the product can be damaged.
A2
Safety Precautions
Caution
Do not shock the product when moving it.
- You may be electrocuted or the product can be damaged
Do not dispose the product-packing box. Use it when you move.
Make the panel face forward and hold it with both hands to move.
- If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center for
repair.
Precautions in Using the Product
Warning
Do not disassemble, repair or modify the product at your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check, calibration or repair.
Do not spray water on the product or scrub with an inflammable substance (thinner or benzene). Fire or
electric shock accident can occur
Keep the product away from water.
- Fire or electric shock accident can occur.
Caution
Do not put or store inflammable substances near the product.
- There is a danger of explosion or fire due to careless handling of the inflammable substances.
When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent
scratching. Do not clean with a wet cloth.
- The water can sink into the product, which can cause electric shock or serious malfunction.
Take a rest from time to time to protect your vision.
Keep the product clean at all times.
Take a comfortable and natural position when working with a product to relax the muscles.
Take a regular break when working with a product for a long time.
Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a
scratch on it.
Keep the proper distance from the product.
- Your vision may be impaired if you look at the product too closely.
Set the appropriate resolution and clock by referring to the User’s Guide.
- Your vision can be impaired.
Use authorized detergent only when cleaning the product. (Do not use benzene, thinner or alcohol.)
- Product can be deformed.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of your local authority.
A3
Important Product Features
Swapping Function
You can swap the main screen and the sub-screen when the PIP/POP/PBP function is used.
Spectacle Function
The screen center area is close to a 4:3 ratio and the outskirt area is expanded by more than
Spectacle. Therefore, the different screen ratio is applied for each area. Because most ordinary
people concentrate their focus on the screen center, a non-linear ratio increase at the outskirt area is
not recognized, which makes it possible to watch 4:3 TV screen with a wide screen.
However, the spectacle function is useful in watching TV or motion pictures but is not suitable for the
PC environment in which you perform graphic or document work.
Sleep Function
When watching AV/TV – The product will be automatically turned off after a certain period of time.
Press this button repetitively to select an appropriate time duration.
A4
Before Connecting to the PC
Before setting up the product, ensure that the power to the product, the computer
system, and other attached devices is turned off.
Unfolding the stand base
Place the product with its front facing downward on a soft cloth.
Push up the back cap.
Back Cap
Hold down the release button inside the stand and strongly pull out the stand with
your two hands.
The stand won't move if you don't press release button.
If the release button does not operate easily, fold the
stand a bit more, and then press the release button.
Inserting batteries into remote control.
1. Take out the battery cap.
2. Insert the batteries with correct polarity (+/-).
3. Close the battery cap.
• You can use a remote control 7 meter distance and 30 degree
(left/right) within the receiving unit scope.
• Dispose of used batteries in the recycle bin to prevent
environmental pollution.
A5
Before Connecting to the PC
Install the speaker covers on the both sides of the speaker for protection.
Installing and removing the cover on/from the speaker
speaker
cover
Installing the speaker cover
Picker
Removing the speaker cover
A6
Name and Function of the Parts
Name of the Remote Control Buttons
Remote Control
MUTE
Use the this button so that no sound comes out temporarily.
POWER
Able to power On/Off.
TV/AV
I/II
SOURCE
*
/SSM
TV
AV1
AV2
S-Video
RGB
PR
If you press the button once,
the following Input Signal
Window will appear. Select
the signal type you want
using the
button.
DVI
OK
VOL
VOL
TV/AV : TV/AV button
PR
TV > AV1 > AV2 > S-Video
I/II : Bilingual choice and sound mode selection
Press this button
[TV]
to switch from Stereo to Mono sound in case of stereo transmission, or
from Nicam Stereo to Nicam Mono, in case of digital transmission.
SWAP
AUTO
TEXT
SLEEP
MODE
M
UPDATE
LIST
TIME
Q.VIEW
MIX
X
SIZE
to switch from Nicam Dual I to Nicam Dual II or Nicam Dual I+II in
case of Nicam Dual transmission.
to choose between Dual I, Dual II or Dual I+II in case of bilingual
transmission :
Dual I sends the primary broadcast language to the loudspeakers ;
Dual II sends the secondary broadcast language to the loudspeakers ;
Dual I+II sends a separate language to each loudspeakers.
[AV]
In AV mode, you can select output sound for the left and right
loudspeakers.
Repeatedly press the I/II button to select the sound output.
L+L : Audio signal from audio L input is sent to
left and right loud-speakers.
L+R : Audio signal from audio L input is sent
to left loud-speaker and audio signal from
audio R input is sent to right loud-speaker.
R+R : Audio signal from audio R input is sent
to left and right loud- speakers.
NOTE : In case of weak stereo sound signals, with stereo or Nicam stereo
transmission, select mono reception.
A7
Name and Function of the Parts
TV/AV
I/II
*/SSM
MENU
Use this button to enter the On Screen Display menu.
EXIT
Use this button to exit the On Screen Display menu.
*/SSM (Sound Status Memory)
Use this button to select the sound tone.
Press repeatedly to select Flat, Music, Movie,
Speech, User sound tone.
PR
OK
VOL
VOL
PR
PR (
) Buttons
Able to change channel.
VOL (
) Buttons
Able to adjust sound.
OK Button
Use when functional adjustment is completed.
Number buttons
Able to directly select and change channel.
AUTO
TEXT
SWAP
SLEEP
MODE
M
UPDATE
LIST
TIME
Q.VIEW
MIX
AUTO Button
•This function is to automatically search the available
channels. It is available to the TV signal inputs only.
•This function is to automatically adjust your display
image to the ideal settings for the current screen
resolution size (display mode). It is available to the
PC analog signal input only.
SWAP function Button
To switch the main-screen and sub-screen in
PIP/POP/PBP mode.
X
SIZE
A8
Name and Function of the Parts
Remote Control
*
PR
OK
VOL
VOL
PR
SLEEP : SLEEP Timer
You can set a time period after which the
TV / AV1 / AV2 / S-Video should switch itself to
standby. Press the key repeatedly to select the number
of minutes.
OFF
10
20
30
240
180
120
90
60
LIST : Programme list
To display the programme list (0~ 99).
PROGRAMME LIST
AUTO
TEXT
SWAP
SLEEP
LIST
TIME
SIZE
Q.VIEW
MIX
HOLD
APC/PSM
REVEAL
X
?
INDEX
i
1_____
2_____
3_____
4_____
5_____
6_____
7_____
8_____
9_ _ _ _ _
10_ _ _ _ _
11_ _ _ _ _
12_ _ _ _ _
13_ _ _ _ _
14_ _ _ _ _
15_ _ _ _ _
16_ _ _ _ _
17_ _ _ _ _
18_ _ _ _ _
19_ _ _ _ _
MODE
M
UPDATE
0_____
Note: TV channels displayed in blue have been
setup to be skipped in the Programme Edit
menu
Q.VIEW : QUICK VIEW Button
* Favourite Program On : Rotate Favourite channel.
* Favourite Program Off : To display the previously
selected TV channel.
APC / PSM Button
Press repeatedly to select Dynamic, Standard, Mild,
Game or User picture mode. This function is not
supported in PC mode.
A9
Name and Function of the Parts
Remote Control - PIP/POP/PBP function
1. Swap Button
You can swap the main screen and the sub-screen when the
PIP/POP/PBP function is used.
PIP
AUTO
SWAP
SWAP
POP
TEXT
SLEEP
MODE
M
UPDATE
SWAP
LIST
TIME
SIZE
Q.VIEW
MIX
HOLD
APC/PSM
REVEAL
X
PBP
2. PIP (Picture in Picture) Button
?
The sub-screen is changed in the order shown below.
: SMALL -> MEDIUM-> LARGE -> OFF
INDEX
i
3. POP (Picture out Picture) Button
The sub-screen moves to the next mode whenever you press
this button.
: POP ON -> PBP(FULL) -> PBP(4:3) -> OFF
PBP (FULL)
POP ON
PBP (4:3)
<Table of PIP/POP/PBP Function Support>
DVI
RGB
TV
AV1
AV2
S-Video
DVI
RGB
TV
AV1
AV2
S-Video
A10
When 'Input Signal 1' comes on in the main
screen, only 'Input Signal 2' can be displayed
on the sub-screen. On the contrary, if the main
screen displays 'Input Signal 2', the subscreen can display 'Input Signal 1' only. You
can swap 'Input Signal 1' and 'Input Signal 2'
using the SWAP button.
Name and Function of the Parts
Remote Control - Using the Teletext function
Please select your local teletext language. (page A31)
If you don't, the teletext may not appear correctly on the screen.
MODE
The mode will be switched in the Teletext
mode.
TIME
AUTO
SWAP
TEXT
SLEEP
MODE
UPDATE
LIST
TIME
SIZE
Q.VIEW
MIX
HOLD
APC/PSM
REVEAL
M
X
?
When viewing a TV programme, press this
button to display the time at the top right
hand corner of the screen.
press this button to select a sub-page number.
The sub-page number is displayed at the
bottom of the screen. To hold or change the
sub page, press the RED/GREEN,
or
NUMBER buttons. Press again to exit this
function.
MIX
Display the teletext pages superimposed on
the TV picture. To switch the TV picture off
press this button again.
INDEX
i
REVEAL
Press the button to reveal/conceal the hidden
information, such as solutions to riddles and
puzzles. Press this button again to remove the
information from the display.
A11
Name and Function of the Parts
Remote Control - Using the Teletext function
*
TEXT
To select the teletext on or off. The main index
page or the last selected page appears on the
screen together with an information headline and
an option line at the bottom of the screen.
PR
OK
VOL
UPDATE
VOL
Press the button to appear the TV programme. At
the top of screen indicates that you are still in the
teletext mode. Before interrupting teletext, you
may select a page number. When the page has
been found, the information line appears briefly
on your screen. Press the button again to
reappear teletext.
PR
SIZE
AUTO
SWAP
Press the button repeatedly to display the upper
part, the lower part and then to return to the
normal page size.
HOLD
TEXT
SLEEP
MODE
M
UPDATE
LIST
TIME
Q.VIEW
MIX
Press the button to stop the automatic rotating of
the subpages. Press the button again to continue
the automatic rotating again.
X
SIZE
INDEX
To display the main index.
HOLD
APC/PSM
REVEAL
?
INDEX
i
A12
Name and Function of the Parts
Rear View
First, pull out the back cap attached to the rear of the product to detach, as shown.
Back Cap
- Open the back cap before
you install the product.
DVI Signal Connector
D-Sub Analogue Signal Connector
PC Audio Jack : Connect to the jack in the PC sound card.
SCART Input/Output Terminal : Connect the SCART CABLE
TV Tuner Jack : Connect the antenna.
Power Cord Connector : Connect the power cord.
Theft prevention locking device
S-Video
S-Video
Headphone/Earphone Connection Terminal
S-Video Input Terminal
VCR(CVBS) Input Terminal
AV Input Terminal (Audio)
A13
Name and Function of the Parts
Connecting the sound card output terminal
•
Make sure to check the sound card connection terminal in the PC before connecting to the product.
If the PC sound card supports both Speaker Out and Line Out, change it to Line Out by setting the jumper
or the PC application. (For more details, refer to the sound card user’s manual.)
- Speaker Out : The terminal connected to the speaker that is not equipped with an amplifier.
- *Line Out : The terminal connected to the speaker equipped with an amplifier.
If Audio Out in the PC sound card has only Speaker Out, reduce the PC volume. This product is integrated
with an amplifier.
TV Output Terminal
Connect to the external device if you record the broadcasting.
When you set the input signal of the main screen as 'TV', you can transmit the signal that you're watching to
the Scart output terminal.
Product
SCART Cable
* Please, use shielded
scart cable
A14
Connecting to External Devices
When Connecting to your PC
First of all, see if the computer, product and the peripherals are turned off.
Then, connect the signal input cable and audio cable.
A When connecting with the DVI-D signal input cable.
B When connecting with the D-Sub signal input cable.
Rear side of the product.
S-Video
PC Audio Input Terminal
- Cect the audio cable to the
LINE OUT jack in the PC sound card.
Audio cable
PC
MAC
A
B
Macintosh Adapter(Not included)
Use the standard Macintosh adapter since an incompatible
adaptor is available in the market. (Different signaling system)
A15
Connecting to External Devices
Connect the power cord.
Rear side of the product.
S-Video
Turn on power by pressing the power button on the product.
Power button
Turn on the PC.
Select an input signal.
Press the SOURCE button on the remote control to select the input signal.
SOURCE
OK
Or, press the SOURCE button at the front side of the product.
SOURCE
TV/AV
AUTO/SELECT
I/II
*/SSM
A
When connecting with a DVI signal input cable.
• Select DVI : DVI-D digital signal.
B
When connecting with a D-Sub signal input cable.
• Select RGB : D-Sub analog signal
TV
AV1
AV2
S-Video
RGB
PR
DVI
OK
VOL
VOL
PR
Note
How to connect to two computers.
Connect the signal cables (DVI and RGB) to each computer.
Press the SOURCE button in a remote control to select the computer to use.
• Directly connect to a grounded power outlet on the wall or a power bar with a ground
wire.
•
A16
Connecting to External Devices
When watching VCR / DVD
Connect the video cable as shown in the below figure and then connect the power cord.
(See page A16)
A When connecting with an SCART cable.
B When connecting with an RCA cable.
• Connect the input terminal with a proper colour
match. (Video – Yellow, Sound (left) – White,
Sound (right) – Red)
Rear side of the Product
Rear side of the Product
S-Video
Red
White
Yellow
RCA Cable
(Not included)
SCART Cable (Not included)
* Please, use shielded scart cable
Y
W
R
VIDEO
OUT
VCR / DVD
VCR / DVD
A17
AUDIO
OUT
Connecting to External Devices
C When connecting with an S-Video cable.
• Connect to the S-Video input terminal to watch high image quality movies.
Rear side of the Product
S-Video
Red
White
S-Video Cable
(Not included)
RCA Cable
(Not included)
R
W
AUDIO
OUT
VIDEO
OUT
VCR / DVD
Select an input signal.
Press the SOURCE button on the remote control to select the input signal.
SOURCE
OK
Or, press the SOURCE button at the front side of the product.
SOURCE
TV/AV
AUTO/SELECT
TV
A
B
C
When connecting with a SCART cable.
• Select AV1
AV1
When connecting with a RCA cable.
• Select AV2
RGB
I/II
*/SSM
AV2
S-Video
PR
DVI
OK
When connecting with a S-Video cable.
• Select S-Video
VOL
VOL
PR
A18
Connecting to External Devices
When watching TV
See if the antenna cable is connected at the rear side of the product and
then, connect the power cord.
Rear side of the Product
S-Video
Antenna Cable
(Not Included)
Select an input signal.
Press the SOURCE button on the remote control to select the input signal.
SOURCE
OK
Or, press the SOURCE button at the front side of the product.
TV/AV
SOURCE
I/II
AUTO/SELECT
• Select TV
*/SSM
TV
AV1
AV2
S-Video
RGB
PR
DVI
OK
VOL
VOL
PR
A19
Connecting to External Devices
To arrange the cables
Connect the signal input cable and the audio cable to use in order to arrange the
power cord, D-Sub cable and DVI-D cable as shown in the following figure.
S-Video
Connect the cable cap according to the steps shown in the following figure.
S-V ide
o
S-V ideo
Cable Cap
S- Vi de
o
S-Video
To remove the cable cap, hold
and pull forward its bottom.
A20
Selecting and Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
Power Indicator
• This indicator lights up blue when the display operates normally(On
Mode). If the display is in sleep (Energy Saving) mode, this indicator
colour changes to amber.
Power Button
• Press the button to turn on the power. Press the button again to turn it off.
MENU Button
• Use this button to show/hide the OSD (On Screen Display) menu screen.
OSD Select /
Adjust Button
• Use the button to select an icon or adjust the setting in the OSD screen.
• Use this button to directly control
brightness and contrast of the PC signal
(RGB, DVI)
• Use this button to control the channel for
the TV signal.
• Adjust the volume.
A21
Selecting and Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
AUTO/SELECT Button
[For PC Analogue signal]
Auto in progress
[For AV1, AV2, S-Video]
• The current signal and mode information will be displayed.
SOURCE Button
SOURCE
AUTO/SELECT
• Select the input signal
TV
AV1
AV2
S-Video
RGB
DVI
IR Receiver
Television
SCART
Composite video
SeparateVideo
D-Sub analog signal
DVI digital signal
TV
AV1
AV2
S-Video
RGB
DVI
• The unit that receives the signal from the remote control.
A22
Selecting and Adjusting the Screen
OSD (On Screen Display) menu
Icon
Function Description
Set/Selects the channel when using the TV
STATION
Adjusts screen brightness, contrast and colour that you prefer.
PICTURE
Adjusting the audio function.
SOUND
Adjusting the timer function.
TIME
Adjusts the screen status according to the circumstances.
SPECIAL
Adjusting Screen Clock/Phase and Position
SCREEN
Adjusting PIP/POP/PBP Mode (Multiple Screen) Functions
PIP/POP/PBP
Note
OSD(On Screen Display)
The OSD function enables you to adjust the screen status conveniently since it provides
graphical presentation.
A23
Selecting and Adjusting the Screen
How to adjust the OSD (On Screen Display) screen.
OK
PR
OK
or
PR
PR
PR
OK
OK
OK
MENU
OK
OK
PR
PR
PR
PR
Pops up
the menu
screen
Move where
you want to
adjust
Select a
menu icon
Move where
you want to
adjust
Select a
menu icon
Adjust the
status
Save/Select
adjustment
Exit from
the menu
screen.
• Use the remote control to adjust the OSD screen.
1
Press the MENU Button, then the main menu of the OSD appears.
2
To access a control, use the
3
When the icon you want becomes highlighted, press the OK Button.
4
Use the
5
Accept the changes by pressing the OK Button and MENU Button.
6
Exit the OSD by pressing the EXIT Button.
Buttons.
Buttons to adjust the item to the desired level.
How to adjust the screen automatically.
You need to adjust the screen display when connecting the product to
a new computer or changing the mode. Refer to the following section to
set an optimal product screen.
Press the AUTO/SELECT button (AUTO button in a remote control)
in the PC analog signal. Then, an optimal screen status will be selected
that fits into the current mode.
If adjustment is not satisfactory, you need to adjust screen position,
clock and phase in the OSD menu.
A24
Auto in progress
Selecting and Adjusting the Screen
Set/Selects the channel when using the TV
Auto programme
Favourite programme
System
Press the
buttons to select the TV system of the country or part of the
world from where you want to receive the TV channels.
If you want to receive 'SECAM L' channel, change the SYSTEM menu to
'L' before launching an automatic search.
L: SECAM L/L (France)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I : PAL I/II (U.K/Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
Storage
from
To select a programme number or enter the programe number with the
number buttons from where you want to start searching for new channels.
If you want to keep the channels 1 to 10 stored earlier, enter programe
number 11. Your TV search for new channels from number 11 onwards.
Start
Press OK button to start automatic programming. all available TV
channels are searched for and stored automatically. To stop auto
programming, press the MENU or EXIT button. When auto programming
is completed, the programme list menu appears.
Manual programme
To change the channel.
(Change each item in Manual Program and
press the "Menu" button to save the
settings)
Favourite programme
System
Press the
buttons to select the TV system of the country or part of
the world from where you want to receive the TV channels.
L: SECAM L/L (France)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I : PAL I/II (U.K/Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
Storage
Press the
buttons to select the channel number or enter the
programme number with the number buttons in where you want to store
channel.
Channel
Press the
buttons to select V/UHF for aerial channels or CABLE for
cable channels.If you know the C-(01~69) or S-channel number(01~47),
enter it directly with the digit buttons 0 to 9.
To select the channel reception type. : V/UHF / CABLE
A25
Selecting and Adjusting the Screen
Set/Selects the channel when using the TV
Name
To see the assigned channel name.
It is possible to change the name stored in the memory or to assign a name
to a TV channel which has not yet been entered. A name with up 5 letters or
numbers can be given to the programme numbers 0 to 99.
Press the
buttons to move cursor to be changed. -> Press the
buttons to select a character.(space, number 0~9, and alphabet A~Z, +,-) ->
Press OK button and MENU button).
Search
Use the
direction.
buttons to search next channel backward or foreward
Programme edit
Favourite programme
Delete
Press the
buttons to select a TV channel to be deleted.
-> Press the red key on the remote control -> The background colour of the
selected channel will change to red.
Press the Delete button one more time to delete the selected channel.
All the following channels are shifted up one position.
Copy
Press the
buttons to select a TV channel to be copyed. ->
Press the green key on the remote control. All the following channel
numbers are shifted down one position.
Move
Press the
buttons to select a channel number to be moved. ->
Press the yellow key on the remote control. -> Press the
buttons to move the TV channel to the desired channel number. ->
Press the yellow key again to release this function.
Skip
Press the
buttons to select a channel number to be skipped. ->
Press the blue key on the remote control. The skipped TV channel is
displayed in blue.
Favourite
programme
ON
Favourite programme
1
C22
2
C23
3
C24
4
C25
5
C26
6
C27
7
C28
8
C29
A26
This function lets you select your favourite
programmes directly. (8 channel)
Press the
buttons to select a
channel number.
* Q.VIEW button(remote control) :
Rotate Favourite channel
Selecting and Adjusting the Screen
Adjusts screen brightness, contrast and colour that you prefer.
PSM
TV/AV1/AV2/S-Video input only
PSM
Dynamic
ACC
Standard
Mild
Game
User
The PSM function automatically adjusts the screen image quality
depending on the AV/TV usage environment.
• Dynamic : Select this option to display with a sharp image.
• Standard : The most general and natural screen display status.
• Mild : Select this option to display with a mild image.
• Game : Select this option to enjoy dynamic image when playing a game.
• User : Select this option to use the user-defined settings.
PSM
Contrast
To adjust the contrast of the screen.
Brightness
To adjust the brightness of the screen.
Color
To adjust the colour to desired level.
Sharpness
To adjust the cleaness of the screen.
Tint
To adjust the tint to desired level. (only 60Hz signal)
Dynamic
ACC
Standard
Contrast
50
Mild
Brightness
50
Game
Color
50
User
Sharpness
50
ACC
PSM
Warm
ACC
Normal
Cool
Selecting a factory setting colour set.
• Warm : Slightly reddish white.
• Normal : Slightly bluish white.
• Cool : Slightly purplish white.
Note
If the PSM setting in the Picture menu is set to Dynamic, Standard, Mild or Game
the subsequent menus will be automatically set.
A27
Selecting and Adjusting the Screen
Adjusts screen brightness, contrast and colour that you prefer.
CSM
RGB / DVI input only
PSM
6500K
CSM
9300K
• 6500K/9300K
Selecting a factory setting colour set.
6500K: Slightly reddish white.
9300K: Slightly bluish white.
• User : Select this option to use
the user-defined settings.
User
PSM
6500K
CSM
9300K
Contrast
50
Brightness
50
Red
50
Green
50
Blue
50
Contrast
To adjust the contrast of the screen.
Brightness
To adjust the brightness of the screen.
Red / Green / Blue
Set your own colour levels.
User
A28
Selecting and Adjusting the Screen
Adjusting the audio function
SSM
SSM
Flat
Balance
Music
AVL
Movie
SRS WOW
Speech
The best sound tone quality will be selected automatically
depending on the video type that you're currently
watching.
• Flat : The most commanding and natural audio.
• Music : Select this option to enjoy the original sound when
listening to the music.
• Movie : Select this option to enjoy sublime sound.
• Speech : Select this option to watch sports broadcasting.
• User : Select this option to use the user-defined audio settings.
User
SSM
Flat
Balance
Music
AVL
Movie
SRS WOW
Speech
User
kHz
1) Select a sound band by pressing the
button.
2) Make appropriate sound level with the
button.
3) Press the OK button to store it for sound
User.
Balance
Use this function to balance sound from the left and right speakers.
AVL
To adjust uneven sound volumes across all channels or signals automatically to the most
appropriate level. To use this feature, select On. (It is adjustble to the TV input signal only.)
SRS WOW
Set the SRS WOW menu on.
The SRS WOW function plays back the mono or stereo sound input with the dynamic surround
effects. It will provide rich and profound sound tone. If you set the SRS WOW on, SSM setting
can not be adjusted.
Note
When connected to your computer and the 'SSM' setting in the audio menu is one of Flat, Movie,
Music or Speech the available menus are Balance, SRS WOW .
is a trademark of SRS Labs,Inc.
technology is incorporated under license from SRS Labs,Inc.
A29
Selecting and Adjusting the Screen
Adjusting the timer function
TIME
Clock
Clock
Off time
On time
Auto sleep
This function is used to set up of current time.
You must set the time correctly before using on/off timer function.
1) Press the MENU button and then use
button to select the TIME menu.
2) Press the
button and then use
button to select the Clock menu.
button and then use
button to set the hour(01~12).
3) Press
button and then use
button to set the minutes(00~59).
4) Press
5) Press
button and then use
button to set the morning(AM) or afternoon(PM).
The default value is __:__.
Off / On time
(Setting is available, however, operation is only allowed upon TV/AV1/AV2/S-Video input)
The off timer automatically switches the set to standby at the pre-set time.
1) Press the MENU button and then use
button to select the TIME menu.
2) Press the
button and then use
button to select Off time or On time.
3) Press the
button and then use
button to set the hour(01~12).
4) Press the
button and then use
button to set the minutes(00~59).
5) Press the
button and then use
button to set the morning(AM) or afternoon(PM).
6) Press the
button and then use
button to select On or Off.
7) Only On time function; Press the
button and then
button to adjust volume level
and program number.
8) Press the OK /MENU button to save.
Auto sleep
(Setting is available, however, operation is only allowed upon TV/AV1/AV2/S-Video input)
If Auto sleep is active and there is no input signal, Make sure there is no remote control
input. the TV swithchs to Off mode automatically after 10 minutes.
button to select the TIME menu.
1) Press the MENU button and then use
2) Press the
button and then use
button to select the Auto sleepmenu.
3) Press the
button and then use
button to select On or Off.
4) Press the OK/MENU button to save.
Note
•
•
•
In the event of power interruption (disconnection or power failure), the Clock must be reset.
Once the On or Off time is set, these functions operate daily at the preset time.
The set must be in Off mode for the On time to work.
A30
Selecting and Adjusting the Screen
Adjusts the screen status according to the circumstances.
Input
Input
TV
Child Lock
AV1
If you press the button once, the following
Input Signal Window will appear. Select
the signal type you want using the
button.
AV2
Language
S-Video
Power Indicator
RGB
Transparency
DVI
Reset
1/2
Child lock
Use the
buttons to select On or Off. The TV can be set up so that it can only be used
with the remote control. This feature can prevent unauthorized viewing.
In order to lock the OSD screen adjustment, set the Child lock tab to the 'On' position.
In order to unlock it, do the following :
* Push the MENU button on the remote control and set Child lock to the 'Off' position.
Language
To choose the language in which the control names are displayed.
Power
Indicator
Use this function to set the power indicator on the front side of the product to On or
Off.
Transparency
To adjust the transparency of the OSD menu screen.
Reset
Use this function to reset the product to the factory default. However, language selection will not
be initialized. (PICTURE, SOUND, TIME, SPECIAL menu)
Teletext
2/2
Teletext
Please select your local teletext language.
If you don't, the teletext may not appear correctly on the screen.
This feature is not available in all countries.
A31
Selecting and Adjusting the Screen
Adjusting Screen Clock/Phase and Position
SCREEN
ARC
Auto-configure
Clock
Phase
Position
To select the image size of the screen.
ARC
<DVI/RGB>
<TV/AV1/AV2/S-Video>
SCREEN
SCREEN
ARC
Auto
ARC
Full
Auto-configure
Full
Auto-configure
1:1
Clock
4:3
Clock
Phase
Spectacle
Phase
Position
Zoom 1
Position
Zoom 2
(1280X1024)
The screen aspect ratio is
changed according to
broadcasting system
signal.
Auto
4:3
Full
Spectacle
Zoom1
Zoom2
AutoConfigure
Clock
This function is suitable for analogue singnal input only. This button is for the automatic
adjustment of the screen position, clock and phase.
Phase
This function is suitable for analogue singnal input only. To adjust the focus of the display.
This item allows you to remove any horizontal noise and clear or sharpen the image of
characters.
This function is suitable for analogue
SCREEN
singnal input only. To adjust position of the
screen.
Press the
button to display the submenu
for position.
Left
Moving the screen position horizontally.
Right
Up
Moving the screen position vertically.
Down
Position
This function is suitable for analogue singnal input only. To minimize any vertical bars or
stripes visible on the screen background. The horizontal screen size will also change.
ARC
Auto-configure
Clock
Phase
Position
H-Position
V-Position
Note
When the Interlace Signal is inputted at the RGB sourec input level, the Auto-Cnfigure, Clock,
Phase and Position menu can't be used.
A32
Selecting and Adjusting the Screen
Adjusting PIP/POP/PBP Mode (Multiple Screen) Functions
(To adjust the sub screen)
On/Off
Off
PIP Input
PIP
Size
POP
Image
PBP
Sound
Position
Swap
On/Off
PIP
After selecting PIP/POP/PBP in the PIP On/Off
menu, the following menu items can be adjusted.
POP
After selecting PIP/POP/PBP in the POP On/Off
menu, the following menu items can be adjusted.
PBP
After selecting PIP/POP/PBP in the PBP On/Off
menu, the following menu items can be adjusted.
PIP Input
To select an input signal for PIP/POP/PBP.
Size
To adjust the size of the PIP/PBP screen. (PIP : Small, Medium, Large / PBP : Full, 4:3)
Image
To adjust the image of the PIP/POP/PBP screen; Press the
button to display the
submenu for PIP/POP/PBP image. Use the
buttons to adjust the item to the desired
level. The items of the sub-menu may vary depending on the type of the source.
Contrast
Adjust PIP/POP/PBP screen contrast.
On/Off
Brightness
Adjust PIP/POP/PBP screen brightness.
PIP Input
Size
Image
Color
Adjust the PIP/POP/PBP screen colour. (TV/AV1/AV2/S-Video)
Sound
Position
Swap
Sound
* The sub-menu can differ according to the type of the input signal.
To turn the PIP/POP/PBP sound on/off.
A33
Selecting and Adjusting the Screen
Adjusting PIP/POP/PBP Mode (Multiple Screen) Functions
Position
To adjust the position of PIP screen.
On/Off
PIP Input
Size
Image
Sound
Position
Swap
Swap
To switch the main-screen and subscreen in PIP/POP/PBP mode.
On/Off
Off
PIP Input
On
Size
Image
Sound
Position
Swap
PIP
SWAP
POP
SWAP
PBP
Note
When the Interlace Signal, such as the Settop Box, is inputted at the RGB and DVI source input
level, the following will be shown.
(1) If Interlace Signal is inputted in RGB, PIP/POP/PBP cannot be used.
(2) If Interlace Signal is inputted in DVI, PIP/POP/PBP cannot be used.
(3) When TV, AV1, AV2, and S-Video is selected as the main screen for PIP/POP/PBP
If the sub-screen is an Interlace Signal inputted RGB or DVI, the screen will be displayed but the
contents will not be displayed.
A34
Troubleshooting
No image is displayed
Is the product power cord connected?
• See if the power cord is properly connected to the
outlet.
Does the power Indicator is turned
on?
• See if the power switch is turned on.
Power is on, power Indicator is blue
but the screen appears extremely
dark.
• Adjust brightness (
Does the power Indicator look amber?
• If the product is in power saving mode, move the
mouse or press any key.
Does the 'Out of Range' message
appear?
• The signal from the PC (video card) is out of the
vertical or horizontal frequency range of the
product. Adjust the frequency range by referring
to the Specifications in this user’s guide.
* Maximum resolution
20.1 inch : 1680 x 1050 @60Hz
Does the 'Check Signal Cable'
message appear?
• The signal cable between PC and product is not
connected. Check the signal cable.
• Press the 'SOURCE' button in the remote control
to check the input signal.
) and contrast (
) again.
'Unknown product' message appears when the product is connected.
Did you install the driver?
• Install the product driver, which is provided with
the product, or download it from the web site.
(http://www.lge.com)
• See if the plug&play function is supported by
referring to the video card user’s guide.
'Controls Locked' message appears.
The “Controls locked” message
appears when pressing local key.
Note
• The control locking function prevents unintentional
OSD setting change due to careless usage. To
unlock the controls.You can only set this function
using the remote control.
* Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times
every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second.
The unit is Hz.
* Horizontal frequency: The horizontal interval is the time to display one vertical line. When the 1 is divided by
horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal
frequency. The unit is kHz.
A35
Troubleshooting
The screen image looks abnormal.
Is the screen position wrong?
• D-Sub analog signal – Press the “AUTO” button in
the remote control to automatically select the
optimal screen status that fits into the current
mode. If adjustment is not satisfactory, use the
Position menu in OSD .
• See if the video card resolution and frequency are
supported by the product. If the frequency is out of
range, set to the recommended resolution in the
Control Panel – Display – Setting menu.
Do thin lines appear on the
background screen?
• D-Sub analog signal – Press the “AUTO” button in
the remote control to automatically select an
optimal screen status that fits into the current
mode. If adjustment is not satisfactory, use the
Clock menu in OSD.
Horizontal noise appears or the
characters look blurred.
• D-Sub analog signal – Press the “AUTO” button in
the remote control to automatically select an
optimal screen status that fits into the current
mode. If adjustment is not satisfactory, use the
Phase menu in OSD.
Screen size is automatically adjusted
when connected to the PC.
• If the screen size is not full when connected to the
PC, execute the PIP/POP/PBP to change to full
screen mode.
No sound appears in the TV channel
display window.
• See if the TV sound is set to mono. If it is, the
sound will not be displayed.
Brightness differs in the main and
sub screen when connected to the
PC.
• You cannot adjust brightness in the PIP/POP/PBP
Screen menu for the sub-screen among
PIP/POP/PBP menus. Therefore, brightness can
be different for the sub-screen.
The screen is displayed abnormally.
• The proper input signal is not connected to the
signal port. Connect the signal cable that matches
with the source input signal.
A36
Troubleshooting
The audio function does not work.
No sound?
• See if the audio cable is connected properly.
• Adjust the volume.
• See if the sound is set properly.
No sound is available when the
PIP/POP/PBP mode is engaged.
• See if the sound is set to On in the PIP/POP/PBP
menu.
Sound is too dull.
• Select the appropriate equalize sound.
Sound is too low.
• Adjust the volume.
The TV function does not work.
The TV signal is not being received.
• See if you have selected the proper channel
mode.
• Use the automatic channel setup function.
• See if the TV antenna is properly connected.
Screen colour is abnormal.
Screen has poor colour resolution
(16 colours).
• Set the number of colours to more than 24 bits
(true colour)
Select Control Panel – Display – Settings
– Colour Table menu in Windows.
Screen colour is unstable or monocoloured.
• Check the connection status of the signal cable.
Or, re-insert the PC video card.
Do black spots appear on the
screen?
• Several pixels (red, green, white or black colour)
may appear on the screen, which can be
attributable to the unique characteristics of the
LCD panel. It is not a malfunction of the LCD.
After-image appears on the product.
After-image appears when the
product is turned off.
• If you use a fixed image for a long time, the pixels
may be damaged quickly. Use the screensaver
function.
A37
Specifications
LCD Panel
Screen Type
20 .1inch (481.84 mm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size: 481.84 mm
0.294 mm
Pixel Pitch
Video Signal
Max. Resolution
D-Sub : 1680 X 1050 @60 Hz
DVI-D : 1680 X 1050 @60 Hz
Recommended Resolution D-Sub : WXGA+ 1680 X 1050 @60 Hz
DVI-D : WXGA+ 1680 X 1050 @60 Hz
Horizontal Frequency
D-Sub : 30 - 83 kHz
DVI-D : 30 - 83 kHz
Vertical Frequency
55 - 75 Hz
Synchronization Type Separate/Composite/SOG (Sync On Green)/Digital
15-pin D-Sub type, DVI-D (digital), S-Video,
Composite video, Scart, TV
Input Connector
Power
Tilt
Dimension/Weight
Rated Voltage
Power Consumption
AC 100-240V~ 50/60Hz 1.2A
On Mode :74W
Sleep Mode : ≤ 4W
Off Mode : ≤ 2W
Tilt Range
-5˚~20˚
Tilt Stand
Attached
Size (WxLxH)
496.4 mm x 241.4 mm x 424.1 mm
496.4 mm x 135.2 mm x 448.7 mm
Weight (excl. package) 8.2 kg (18.0 lbs)
Environmental Conditions Operational Condition Temperature: 10˚C ~ 35˚C , Humidity: 10% ~ 80%
Storage Condition
Temperature: -20˚C ~ 60˚C , Humidity: 5% ~ 95%
A38
Specifications
PC Mode – Preset Mode
Preset mode
1
2
3
4
5
6
7
VGA
VGA
VGA
VESA
VESA
VESA
VESA
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
31.468
31.469
37.500
37.897
46.875
48.363
60.123
70
60
75
60
75
60
75
Preset mode
8
9
10
11
VESA 1152 x 864
VESA 1280 x 1024
VESA 1280 x 1024
VESA 1680 x 1050
Horizontal Vertical
Frequency Frequency
(kHz)
(Hz)
67.500
63.981
79.976
65.290
75
60
75
60
Power Indicator
Mode
Product
On Mode
Sleep Mode
Off Mode
Blue
Amber
-
VESA wall mounting
VESA wall mounting
Connected to another object. (stand type and wall-mounted type.)
This product accepts a VESA-compliant mounting interfacepad.(This has to be
purchased separately if required.)
For further information, refer to the VESA Wall Mounting Instruction Guide.
Theft prevention locking device
Locking Device
Use this locking cable (This has to be purchased
separately if required.) to prevent theft.
S-Video
A39
Specifications
DVI-D
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Signal
T. M. D. S. Data 2T. M. D. S. Data 2+
T. M. D. S. Data 2/4 Shield
T. M. D. S. Data 4T. M. D. S. Data 4+
DDC Clock
DDC Data
Analogue Vertical Synchronization
T. M. D. S. Data 1T. M. D. S. Data 1+
T. M. D. S. Data 1/3 Shield
T. M. D. S. Data 3T. M. D. S. Data 3+
+5V Power
Grounding (return for +5V, horizontal sync and vertical sync)
Hot Plug Detect
T. M. D. S. Data 0T. M. D. S. Data 0+
T. M. D. S. Data 0/5 Shield
T. M. D. S. Data 5T. M. D. S. Data 5+
T. M. D. S. Clock Shield
T. M. D. S. Clock+
T. M. D. S. Clock
T.M.D.S. (Transition Minimized Differential Signaling)
A40
Download PDF

advertising