LG | STUDIOWORKS-563N | LG STUDIOWORKS 563N Owner’s Manual

Thank you for purchasing a high resolution monitor. It will give you high
resolution performance and convenient reliable operation in a variety of
video
operating modes.
Features
The Studioworks 563N/563A is
a 15 inches (14.0 inches viewable ) intelligent,
microprocessor based monitor compatible with most analog RGB (Red, Green,
Blue) display standards, including IBM PC , PS/2 , Apple , Macintosh , Centris ,
Quadra , and Macintosh II family.
The monitor
provides crisp text and vivid color graphics with VGA, SVGA, XGA,
Ergonomic modes (non-interlaced), and most Macintosh compatible
color video cards when used with the appropriate adaptor. The monitor's wide
compatibility makes it possible to upgrade video cards or software without
purchasing a new monitor.
and VESA
Digitally controlled auto-scanning is done with the micro-processor for horizontal
frequencies between 30 and 61kHz, and vertical scan frequencies
scan
between 50-120Hz.
This monitor is
dots and
a
capable of producing
a
maximum horizontal resolution of 1024
maximum vertical resolution of 768 lines.
The
microprocessor-based digital controls allow you to adjust conveniently a
variety of image controls by using the OSD (On Screen Display).
On Screen
Display(OSD) adjustments in seven languages:
English, Deutsch, Francais, Espanol, Italiano, Portugues, Korean for ease of
setup and screen optimization
Plug and play capability if supported by your system.
This monitor has DDC 2B function.*
Compliant with
-
-
the
following regulated specifications
:*
EPA ENERGY STAR
MPR II
(Applies to 563N only)
*For detailed information, please refer to
the Reference Guide
provided
.
Connecting
the Monitor
Turn off the
Carefully
equipment and all attached options.
set the monitor face-down with the underside
facing
you.
Installation
1.
Align the hooks
on
the tilt/swivel stand with the
matching slots
in the base of
the monitor.
2. Insert the hooks into slots.
3. Slide the tilt/swivel stand toward the front of the monitor until the latches click
into the locked
position.
Slots
Latch
Hooks
Hooks
Latch
A2
Connecting
the Monitor
On the back of the monitor
power
1
2
cord,
are
plug-in connections; one for the AC
signal cable from the video card.
two
and the other for the
Power off both the monitor and PC.
Connect the 15 pin VGA connector of the supplied signal cable to the output
on the PC and the matching input connector on the rear
VGA video connector
of the monitor. The connectors will mate only one way. If you cannot attach
easily, turn the connector upside down and try again. When mated,
the cable
tighten the thumbscrews
2'
to secure the connection.
appropriate MAC to VGA adapter block at your local computer
adapter changes the high density 3 row 15 pin VGA connector to
the correct 15 pin 2 row connection to mate with your MAC. Attach the other
end of the signal cable to the side of the adapter block with 3 rows.
Locate the
store. This
Connect the attached adapter block/signal cable to the video output
MAC.
3
on
your
One end of the AC power cord is connected into the AC power connector on
the back of the monitor. The other end is plugged into a properly grounded
three-prong AC outlet.
4
5
Power ON the PC, then the monitor.
If you
see
the SELF DIAGNOSTICS message, check the
signal cable and
connectors.
6 After using the system, power OFF the monitor, then the PC.
IBM PC
MACINTOSH
Mac
D-15P
2
Adapter
2'
D-15P
3
Power Cord
Signal
Cable
*
NOTE
:
For
Apple
Macintosh use,
separate plug adapter is needed
change the
15
pin high density (3 row)
on the supplied
pin 2 row connector.
D-sub VGA connector
cable to
A3
a
15
a
to
Location and Function of Controls
Front View
MENU
SELECT
Power ON/OFF Button
Power Indicator
MENU Button
SELECT Button
Button
Rear View
ID Label
AC Power Socket
D-Sub
Signal Cable
A4
Control Panel Function
Front Panel Controls
MENU Button
SELECT Button
Power ON/OFF Button
MENU
SELECT
Power
Button
Control
(DPMS)
Indicator
Function
MENU
MENU Button
Use this button to enter
or
exit the
on screen
display.
Button
Use these buttons to choose
the
SELECT
SELECT Button
on screen
a
selection in the
Use this button to turn the monitor
Power (DPMS)
Indicator
This Indicator
lights
on or
off.
up green when the
operates normally. If the monitor is in
DPM (Energy Saving) mode (standby/suspend/power off), this indicator
changes to amber.
A5
on
display.
Power ON/OFF
Button
monitor
items in
adjust
display.
Use this button to enter
screen
or
color
On Screen
Display (OSD) Control Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor are quick and easy with the On Screen Display Control system.
A quick example is given below to familiarize you with the use of the controls.
Following section is an outline of the available adjustments and selections you
can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
To make
adjustments
in the On Screen
Display, follow these steps:
SELECT
MENU
MENU
12
SELECT
Press the MENU Button, then the main
To
acces a
becomes
control,
making image adjustment.
use
highlighted,
the
or
menu
of the OSD appears.
Buttons. When the icon you want
press the SELECT Button.
3
Use the
45
Accept the changes by pressing the SELECT Button.
Exit the OSD
Buttons to
adjust the item
to the desired level.
by Pressing the MENU Button.
A6
On Screen
You
were
Display(OSD) Selection
introduced to the
and
Adjustment
procedure of selection and adjusting an item
the OSD
using
descriptions
system. Listed below are the icons, icon names, and icon
of the items that are shown on the Menu.
OSD
Adjust
Description
CONTRAST
Adjust the display to the contrast desired.
31.4kHz/70Hz
CONTRAST
50
U
BRIGHTNESS
31.4kHz/70Hz
Used to
BRIGHTNESS
adjust the brightness
of the
screen.
50
U
H POSITION
31.4kHz/70Hz
H
To
POSITION
50
move
picture image
Moves the
screen
Moves the
screen
left and right.
image left.
image right.
U
H SIZE
31.4kHz/70Hz
H
To
SIZE
adjust image
width.
Decreases the size of the
50
screen
image.
Increases the size of the
U
screen
image.
V POSITION
To
31.4kHz/70Hz
V
POSITION
50
U
A7
move
image
up and down.
Moves the
screen
Moves the
screen
image
image
down.
up.
On Screen
Display(OSD) Selection
OSD
and
Adjust
Adjustment
Description
V SIZE
31.4kHz/70Hz
V
To
SIZE
adjust image height.
Decreases the size of the
50
screen
image.
Increases the size of the
screen
image.
U
PINCUSHION
To correct the
31.4kHz/70Hz
PINCUSHION
bowing
in and out of the
image.
50
Curves the
image's edges
inwards.
Curves the
U
image's edges
outwards.
TRAPEZOID
31.4kHz/70Hz
To correct
TRAPEZOID
geometric
Makes the
50
at the
the
image
narrower
screen
image
wider at
top.
Makes the
U
distortion.
screen
top.
PIN BALANCE
31.4kHz/70Hz
PIN
To correct the balance of both sides
BALANCE
bowing.
50
Curvature of the sides to the
right.
Curvature of the sides to the left.
U
PARALLELOGRAM
31.4kHz/70Hz
This control
PARALELOGRAMO
screen
50
adjusts
image.
Tilts the
screen
Tilts the
screen
for
a
skewing
of the
image leftward.
image rightward.
U
V MOIRE
31.4kHz/70Hz
Reduce vertical moire when
V
interference
patterns of dark steady
wary lines appear on your screen.
The moire adjustments may affect the
focus of the screen.
MOIRE
0
U
A8
On Screen
Display(OSD) Selection
OSD
and
Adjust
Adjustment
Description
COLOR
Select the desired color
temperature
(9300K, 6500K) or select user
your own color levels(R/G/B).
31.4kHz/70Hz
COLOR
U
?
9300
:
?
6500
:
?
RGB
:
Slightly
Slightly
to set
bluish white.
reddish white.
To set your own color levels.
Allow for specific
adjustments to Red, Green,
Blue (R/G/B).
31.4kHz/70Hz
COLOR
Decreases the amount of
9300
6500
RGB
color in the
R
90
G
90
B
80
image.
Increases the amount of
color in the
image.
To exit the COLOR OSD
:
RECALL
You
31.4kHz/70Hz
can use
this function when you want
to go back to the
RECALL
screen
time you
the
purchased
adjusting to modify it
When you
U
in the Preset Mode.
in the User
are
recall
only
using Recall, adjust the
again if necessary.
,
If you want
Preset
display of the
product after
,
more
mode, you
,
screen
information
can
items. After
display
on
the
Mode, refer to A11 page.
LANGUAGE
31.4kHz/70Hz
To choose the
LANGUAGE
control
OSD Menus
and Korean.
31.4kHz/70Hz
LANGUAGE
ENGLISH
DEUTSCH
AIS
ESPAN
OL
the
are
available in
seven
languages : English, German,
French, Spanish, Italian, Portuguese
U
FRANC
language in which
displayed.
names are
ITALIANO
A9
On Screen
Display(OSD) Selection
OSD
and
Adjust
Adjustment
Description
DEGAUSS
31.4kHz/70Hz
Used to
DEGAUSS
give
demagnetize
a move
accurate
the
picture
image and
to
color.
U
INFORMATION
31.4kHz/70Hz
To inform
INFORMATION
mode data.
U
31.4kHz/70Hz
INFORMATION
PRESET
MODE
1
60.0kHz
/
76Hz
2
31.4kHz
/
61Hz
3
37.4kHz
/
76Hz
4
43.2kHz
/
86Hz
5
31.4kHz
/
71Hz
6
46.8kHz
/
76Hz
A10
users
of
preset and
user
The monitor has 16 memory locations for
factory preset to popular video modes.
display modes, 7 of which are
Display Modes (Resolution)
1234567
VESA
640
x
480
31.47
60
VESA
720
x
400
31.47
70
75
VESA
640
x
480
37.50
VESA
640
x
480
43.27
85
VESA
800
x
600
46.88
75
VESA
800
x
600
53.67
85
VESA
1024
60.02
75
x
768
User Modes
Modes 8
-
16
are
empty and
can
accept
new
video data. If the monitor detects
video mode that has not been present before or is not one of the preset
modes, it stores the new mode automatically in one of the empty modes
a new
starting with mode 8.
If you use up the 9 blank modes and still have more new video modes, the
monitor replaces the information in the user modes starting with mode 8.
Recalling Display Modes
When your monitor detects a mode it has seen before, it automatically recalls
the image settings you may have made the last time you used that mode.
You may, however, manually force a recall of each of the 7 preset modes by
pressing the Recall button. All preset modes are automatically recalled as the
monitor
The
senses
the
incoming signal.
ability to recall the preset modes is dependent
on
the
signal coming from
factory
your PC's video card or system. If this signal does not match any of the
modes, the monitor automatically sets itself to display the image.
Troubleshooting
Check the
following before calling for service.
SELF DIAGNOSTICS message.
The signal cable is not connected, or is loose. Check and
secure
the connection.
OUT OF FREQUENCY message appears.
The frequency of the signal from the video card is outside the operating
range of
the monitor.
*
Horizontal Frequency : 30-61kHz
Vertical Frequency : 50-120Hz
*
Use the
graphics board's utility software to change the frequency setting (Refer
graphics board).
to the manual for
The power LED is illuminated amber.
Display power management mode.
There is no active signal coming from the PC.
The signal cable is not fastened securely.
Check the computer power and graphics adapter configuration.
image on the SCREEN is
rectangle shape.
The
Image adjustment
not been done
MENU, SELECT and
not
centered,
yet in the
current
buttons to set the
image
or
too
small,
or
not a
operating mode. Use the
to your liking.
The monitor doesn't enter the power saving off mode (Amber).
Computer video signal is not VESA DPMS standard. Either the PC or the video
controller card is not using the VESA DPMS power management function.
An abnormal
picture is displayed on the screen. For example, the
picture may be missing or dark.
upper part of the
If
using certain non-VESA Standard video card, an abnormal picture may be
displayed. Try setting it to one of the factory preset modes, or selecting to a
resolution and refresh rate within the specification limits of the monitor.
NOTE
If the power indicator(LED)
the monitor.
light
is
blinking amber,
Then press a power ON/OFF button
technician for more information.
on
the front
A12
may result in abnomal condition of
panel
control and call your service
Specifications
Picture Tube
15 inch (14.0 inches viewable)
90
degree deflection
0.28mm Dot
pitch
Studioworks 563N: AGAS(Anti-Glare Anti-Static) coating
Studioworks 563A: Glare
Sync Input
Horizontal
Vertical
Input
Video
Input
30
Freq.
50
Freq.
Form
-
-
61kHz (Automatic)
120Hz (Automatic)
Separate TTL, Positive/Negative
pin D-Sub Connector
Signal Input
15
Input Form
Separate, RGB Analog, 0.7Vp-p/75 ohm,
768@75Hz
Resolution(max)
1024
Power
Normal
≤
74W
Consumption
Stand-by/Suspend
≤
15W
Power Off
≤5W
Width
35.6
cm
/ 14.02 inches
Height
37.1
cm
/ 14.6 inches
Depth
39.5
cm
/ 15.5 inches
Dimensions
tilt/ swivel
Power
(with
stand)
Input
x
AC 100-240V 50/60Hz 1.5A
Weight
Net
Environmental
Operating Condition
Conditions
11.7
kg (25.79 lbs)
Temperature
10 ˚C to 40 ˚C
Humidity
10 % to 90 %
Storage
non-Condensing
Condition
Temperature
0 ˚C to 60 ˚C
Humidity
5 % to 90 %
non-Condensing
NOTE
Information in this document is
represent
a
commitment
on
subject to change without
the part of LG Electronics Inc.
A13
notice and does not
Positive
Download PDF

advertising