LG | DRD-820B | LG DRD-820B Owner’s Manual

DVD-ROM DRIVE
OWNER'S MANUAL
MODEL
To
:
DRD-820B
enjoy fully all the features and functions of your DVD-ROM Drive,
carefully and completely.
Please read this Owner's Manual
English
CAUTION: The laser used in the DVD-ROM drive
Do not
attempt
to open the
can
To reduce the risk of electric shock, do not
No user-serviceable
Refer
servicing
to
damage
your eyes.
cover.
remove cover
(or back).
parts inside.
qualified
service
personnel.
COMPACT
This unit
uses
CD-ROM discs
marked with this
Use of controls
symbol:
performance
or
of
other than those
procedures
specified
herein may result in hazardous radiation
exposure.
PRODUCT COMPLIES WITH DHHS
RULES 21 C.F.R. SUB-CHAPTER J,
IN EFFECT AT THE DATE OF MANUFACTURE.
WARNING: To reduce the risk of fire
do not expose this
electric shock,
or
to rain
appliance
or
moisture.
CSA Notice
This class B
digital apparatus
meets all
requirements
of the Canadian
Interference-Causing Equipment
Regulations.
Cet
appareil numerique
de la classe B
respecte
toutes les
exigences
du
Reglement
sur
le materiel brouilleur
du Canada.
FCC COMPLIANCE STATEMENT
: This equipment has been tested and found to comply with the limits for
Note
a
Class B
digital device,
to Part 15 of the FCC Rules.
pursuant
These limits
designed to provide reasonable protection against harmful interference in a
equipment generates, uses, and can radiate radio frequency energy and,
are
residential installation. This
if not installed and used in accordance with the instructions, may cause harmful interference to radio
no guarantee that interference will not occur in a particular
communications. However, there is
installation. If this
can
interference
-
-
-
-
Reorient
equipment does cause harmful interference to radio or television reception, which
by turning the equipment off and on, the user is encouraged to try to correct the
by one or more of the following measures:
be determined
relocate the
or
receiving
antenna.
Increase the
separation
between the
Connect the
equipment
into
Consult the dealer
?
outlet
equipment
on a
and receiver.
circuit different from that to which the receiver is connected.
Authorized Service Center for
help.
FCC WARNING
Changes
or
the user's
?
or an
an
modifications not
authority
to
expressly approved by the party responsible for compliance could void
operate the equipment.
This DVD-ROM Drive is for
instructions
detailing
user
use
only
with UL listed
personal computers
installation of card cage accessory.
E-2
that have installation
FEATURES
FEATURES
ATAPI/E-IDE interface
Average
time (DVD-ROM:150ms, CD-ROM:100ms)
compatible
access
Multimedia PC
Photo CD multisession
support
Small CPU band width
(MPC spec.)
Data transfer rate(DVD-ROM 2x-speed:2.70MB/sec,
CD-ROM max-24x-speed: 3.6MB/sec)
Intelligent 256KB data buffering system
Horizontal mounting support
Tray Loading system without caddy
Designed for internal mounting
Emergency Eject Support
Easy audio CD control button support
Supports Windows 95 Plug and Play ATAPI protocol
CD-R, CD-RW Support
SYSTEM REQUIREMENTS
An IBM PC
or
compatible
with the
following system components:
IBM
Compatible Pentium-133 MHz or above
(With PIO mode 4, TX chip set recommended)
A Minimum of 16MB memory
Floppy
disk drive
(3
MS-DOS version 3.1
1/2
inch)
or
greater
An open,
drive
An
PC with
front-facing, half-height
existing IDE controller in your
bay.
an
available cable connector
IDE controller that you will install.
SUPPLIED ACCESSORIES
Quantity
Item
1
Owner's Manual
Setup
1
Diskette
1
Audio Cable
E-3
or a new
LOCATION AND FUNCTION OF CONTROLS
COMPACT
ROM
CD
CD
DVD
1
3
2
4
Figure
5
67
1. Front View
FRONT VIEW
1
Headphone Jack
jack for monitoring
3.5mm
2
3
the audio
Headphone Volume Control
Adjusts the headphone sound
Busy Indicator (DVD, CD)
Busy Indicator lights during
a
Play/Skip
When
an
CD-ROM/DVD-ROM disc
skip
7
operations.
on
its
tray.
Button
Audio CD is in the Disc
audio CDs from the first track. If
6
initialization and data-read
Disc Drawer
Accepts
5
from audio CDs.
level.
The
4
signal
Drawer, pressing this button will
an
audio CD is
playing, pressing
start
playing
this button will
to the next track.
Emergency Eject Hole
Insert a paper clip here to eject
the drawer
manually
or
when there is
no
power.
Open/Close/Stop Button
pressed to open or close the CD tray.
The button works only when the main power switch is on.
If an audio CD is playing, pressing this button will stop it, and pressing
This button is
open the tray.
E-4
it
again
will
DIGITAL
AUDIO
ANALOG
AUDIO
INTERFACE
POWER
+5
DRC
G39
GL
S M
1
40
2
SLA
12
3
GND
4
Figure
+12
5
2. Back View
BACK VIEW
1
Digital
Audio
This is
a
You
2
can
Ouput Connector
digital audio output connector or Video
connect this to the digital audio system
CD
or
output
connector.
Video CD Board.
Audio
Output Connector
Output Connector connects to a sound card.
supplied audio cable is a SoundBlaster type cable.
Analog
The Audio
The
sound
card, you will need
proper cable for that card. This cable is necessary to
3
Master / Slave / CSEL
These three
Slave,
or
jumpers
If you have
a
different
to contact the sound card manufacturer to obtain the
play
audio CDs.
Jumper
are
used to set the DVD-ROM Drive to either
a
Master,
CSEL drive.
Refer to section HARDWARE INSTALLATION.
4
Interface Connector
This
40-pin
connector
is
used to transfer and
control
signals
between
DVD-ROM Drive and your PC.
Connect the 40-pin IDE cable in your PC to this connector.
5
Power-in Connector
Attach
a
power cable from the
computer's
E-5
power
supply
to this connector.
the
INSTALLATION, USAGE
AND HANDLING PRECAUTIONS
Installation
Avoid
-
-
-
-
placing the drive
high humidity
high temperature
in
a
location
subject
to
:
mechanical vibration
direct
sunlight
Operation
-
During operation,
excessive
vibration,
or a
sudden
jolt
to the drive may
cause a
malfunction.
-
Avoid
exposing
the drive to sudden
changes
in
condensation to collect inside the drive.
Transportation
-
Always
remove
the disc before
moving
E-6
the drive.
temperature. This may
cause
HARDWARE INSTALLATION
This section describes how to install your DVD-ROM drive into your
computer.
WARNING:
To
protect the DVD-ROM Drive, your computer, and peripheral devices from damage,
turn off their power before
Note:
If you
drive
are
installing
the drive.
not comfortable about
your PC and
opening
installation, many local computer shops
attempting the DVD-ROM
perform this service for a
can
reasonable cost.
This installation
assumes you have a PC with an available connector on an IDE
interface cable. If your PC has an IDE hard drive, there is usually an available connector
in the middle of the same cable that attaches from the motherboard (or controller card)
IDE connector to the hard drive. Some PC's have 2 IDE
controller
card, and you may need
to
purchase
on
ports
IDE cable to
on
the motherboard
use an
unused IDE
or
port.
If you do not have an available IDE connector or IDE
IDE controller card to install this DVD-ROM drive.
an
system will make your installation easier and less
A final note before installation: The cable
IDE cable. Do not
attempt
port, you may need to purchase
Inspecting and knowing your PC
time consuming.
connecting
to your
If the DVD-ROM drive is to be connected to the
same
that the hard drive is set
can
as
master. Hard drives
Check your hard drive owner's manual
correct
floppy
disk drive is not
an
to attach the DVD-ROM drive to this cable.
or
cable
be set
as
the hard
drive, be
single, master,
as
or
sure
slave.
contact the hard drive manufacturer for
jumper settings.
SETTING MASTER / SLAVE JUMPER
*
You will
This
see
jumper
in your PC.
three
pairs
of
pins
and
a
jumper (cap)
is used to set the DVD-ROM Drive
Examples
of how the
jumper
can
be
at the back of the DVD-ROM drive.
as a
CSEL, MASTER,
placed
are
shown in
Note
:
or
SLAVE device
Figure
3 below.
The
jumper is always
placed vertically,
NEVER SIDEWAYS!
CSEL
mode
SLAVE MASTER
mode
mode
(rear
(default)
Figure
*
Move the
CSEL
your
or
jumper (clip
MASTER
system), using
as
3.
of DVD
Setting
on one
needed
the above
-
ROM
drive)
MASTER / SLAVE
Jumper
pair of pins) from its default factory position (SLAVE) to
(see the following description for the setup that matches
diagram to place the jumper.
E-7
WHEN USING A PRIMARY IDE CONTROLLER
Most PCs
(one for hard disk, the other for a
originates either on the motherboard
or on a controller card. This controller is termed the primary IDE controller, and the hard disk
attached that contains the operating system for boot-up is set up as the Primary Master. Your
provide
second hard disk
one
or a
IDE cable to
DVD-ROM
support
drive).
two devices
This IDE cable
DVD-ROM drive should be set to the Slave mode.
Hard Disk Controller Card
(This card may
be
a
connector
on
the
Motherboard)
IDE cable
Primary
IDE Channel
Primary Slave
Primary Master
(Hard Disk or
(Hard Disk for
DVD-ROM Drive)
Boot-up)
Card Slot
Motherboard
Figure
4.
Primary
Controller
E-8
system Configuration
WHEN USING A SECONDARY CONTROLLER
*
If your PC has an additional IDE controller on the motherboard or in a system slot, each
IDE device connected to the secondary IDE controller must also be set to the Master or
Slave mode. If you are connecting your DVD-ROM drive to a secondary IDE port, and it
is the 1st device you are connecting to it, then set the DVD-ROM jumper to the Master
If it is the 2nd
position.
*
device,
set the DVD-ROM
jumper
to the Slave
position.
Depending on the IDE card and whether the DVD-ROM drive is a master or slave
unit, the diagram below represents the different ways in which the DVD-ROM may
be configured in your PC. The table below the diagram shows the possible Jumper
placements that would correspond to each of the different configurations shown.
Secondary
IDE
Controller CARD
Secondary
IDE Channel
Card
Motherboard
on
or
Hard Disk Controller Card
(This
card may be
a
connector
on
the
Primary
Secondary Master Secondary Slave
(Hard Disk or
(Hard Disk or
DVD-ROM Drive)
DVD-ROM Drive)
5. Possible
System Configuration
If you have the system with two IDE channels (in the
do not install an IDE controller card in your system.
IDE Controller
Primary (1st
IDE
card)
disk is
Secondary (2nd
card)
Master(1st device on
Secondary (2nd
IDE
card)
Slave(2nd
use
device
on
CSEL
of
an
enhanced IDE
Jumper
SLAVE
Master)
IDE
PC Manual says
case
DVD-ROM Connection
Slave(Hard
IDE Channel
Primary Slave Primary Master
(Hard Disk or (Hard Disk for
DVD-ROM Drive)
Boot-up)
Card Slot
Motherboard
Figure
Motherboard)
E-9
Placement
(default)
2nd IDE
Card)
MASTER
2nd IDE
Card)
SLAVE
CSEL
PC),
(default)
MOUNTING THE DVD-ROM DRIVE
Step
1. Turn
off
and
computer
and
unplug your
peripheral
all
devices attached to it.
Step
2. Remove
the
cover
from
your
computer.
Step
3. Remove the front
unused
Figure
6.
Removing
the
panel
half-height
from
an
slot.
Blanking plate
Step
4. Slide
the
the
DVD-ROM
drive
half-height slot, and
the drive in
place
with
into
secure
screws.
Note: If there is too much space between
the sides of the drive and the drive
bay,
you may need to install spacer
at your local
brackets, available
computer store.
Figure
7.
Mounting
Pin
The
the Drive
assignment
pin assignment
connector is
as
Step
of the
follows:
5V DC
(4-pin
Figure
supply
12V DC
connector
connection
8.
cable)
Connecting the
Supply Cable
the
connector.
GND
Power
5. Push
connector
power-in
Power
E-10
power supply cable
into the power in
firmly
Step
6. Connect the
40-pin
connector
Please make
Red-edge
edge
of
the
sure
Connecting
on
Cable
is
the DVD-
ROM Drive.
IDE Cable
9.
that the red
IDE
connected to Pin 1
Figure
IDE Cable to
the back of the DVD-ROM Drive.
Pin 1
Interface
the IDE Cable
to the Interface Connector
CONNECTING AN AUDIO CABLE
If you want to connect audio equipment or
sound card to the DVD-ROM drive, use
Pin
assignment
The pin assignment of the
audio output connector is
as
a
an
follows.
GND
GND
L-Channel
R-Channel
Audio
Cable
to Audio
Equipment
(sound card)
*
Pin
assignment
of the audio cable
GND
L-Channel
Figure
10.
audio cable to connect the drive to the
sound device.
Connecting
to the Audio
GND
R-Channel
an
Audio Cable
Output
Connector
E-11
SOFTWARE SET UP
To have your PC recognize and be able to use the new DVD-ROM drive, driver files
must be installed. Depending on your operating system, this procedure may be
completely automatic or may require using the supplied software. Locate your operating
system type from the section below, and follow the appropriate directions.
Windows 95, Windows
ATAPI Installation
*
For Windows 95
NT, OS/2 Warp(ATAPI Installation)
(Windows
installation,
95 and
do not
use
others)
the installation diskette
supplied. This DVDWarp compatible, generally
operating systems Below is
other operating systems, try
ROM drive is Windows 95, Windows NT 3.5, and OS/2
utilizing the generic software drivers supplied with those
the
example installing the driver for Windows
looking for either a LG Electronics or Goldstar
If none is found, try selecting one of the device
(For
Windows
95. For
IDE DVD-ROM drive software driver.
drivers for Non-listed IDE CD-ROM.
95)
1. Install the DVD-ROM drive in your PC
as
described in this manual.
2. Power up your PC. Upon starting Windows 95, it might automatically detect the
ROM drive and load the driver software for it. If not, proceed to the next step.
3. In Windows
95, Click
on
the Start button. Click
Control Panel button. Double-Click
instructions for the
computer
on
the
Settings
button. Click
the Add New Hardware
to search your
the DVD-ROM drive and load the
on
generic
system for
new
new
DVD-
on
the
icon. Follow the
hardware. It will locate
driver.
DOS, WINDOWS 3,11
The INSTALL program performs the following functions.
*
Allows the user to select the target disk drive where DVD-ROM device driver files will
be
*
*
*
*
*
set-up.
Unless modified
by the user, the INSTALL program searches the target disk for
directory (\DVDROM); if it is not found, the directory (\DVDROM) is created.
Copies the DVD-ROM device driver file named LGDVDROM.SYS, the Microsoft CD-ROM
Extension file named MSCDEX.EXE, and the utility files to the specified directory.
Modifies your CONFIG.SYS file to list the location and
Modifies your AUTOEXEC.BAT file to load MSCDEX.
Terminates and returns control to the
name
of the device driver.
user.
LIST OF FILES TO BE INSTALLED IN YOUR PC
MSCDEX.EXE
Microsoft MS-DOS CD-ROM Extension
enables the
computer
to
access
LGDVDROM.SYS
DVD-ROM device driver for DOS.
EJECT.EXE
Software
CLOSE.EXE
Software close program which
eject
program which
E-12
software, which
the DVD-ROM drive.
can
can
eject
the CD
tray.
close the CD
tray.
RUNNING THE INSTALL PROGRAM
Step
(DOS INSTALLATION)
1. Insert the DVD-ROM device driver for DOS install diskette into the
appropriate
drive.
Step
2. Go to the
Step
3.
Step
4. The
drive
by typing
A:
or
the word INSTALL and press
B: at the DOS
as
Follow the instructions
6. If you
specify the path
on
the
modify
complete,
the
screen.
information
during the installation,
the install program will copy
LGDVDROM.SYS, the Microsoft CD-ROM
Extension file named MSCDEX.EXE and the
and
appropriate.
[ENTER].
the DVD-ROM device driver file named
Step
prompt,
INSTALL program will begin loading. When loading is
INSTALL program identification will appear on the screen.
Step.5.
Step
Type
floppy
utility
files to the
specified directory,
your CONFIG.SYS file and AUTOEXEC.BAT file.
7. When the installation is
completed,
remove
the diskette and reboot your PC.
CD-ROM EXTENSION PROGRAM MSCDEX. EXE OPTIONS
There
are several options that are set for the Microsoft CD Extension program.
Generally, these settings do not have to be changed for the DVD-ROM drive to work, so
these options are needed no further. However, you may decide to change the MSCDEX
option settings depending on your operating environment.
These options are explained below:
PARAMETER
DESCRIPTION
Tells MSCDEX.EXE what the device driver's
/D
(Device Name)
be
same as was
in CONFIG.SYS
/E
/L:
/M:
used in /D:
(Value)
is
(must
line
use
expanded
Indicates the drive letter to be
memory
assigned
to the DVD-ROM
drive
Tells MSCDEX.EXE how much memory to allocated for
caching. Default is 10 (represents 10 kilobytes).
Provides
/V
name
of DEVICE=
file)
Tells MSCDEX.EXE to
(Device Name)
expression
memory usage statistics, such as how much
is
used by buffers, resident data, and resident
memory
code.
E-13
TROUBLESHOOTING
*
When the DVD-ROM drive does not work with the hard disk drive in
primary
IDE channel.
(SOLUTION)
1. Check the DVD-ROM drive Master/Slave
Jumper setting.
The DVD-ROM drive must be set to the Slave mode.
2. Check to be
sure
your hard disk Interface type is IDE type.
3. Check your hard disk Master/Slave Jumper setting.
Some old-version IDE type hard disks were set to Master
In that case, contact your hard disk company and
setting to master mode.
4. If the
Only mode.
change your hard
disk
jumper
DVD-ROM drive does not work with above methods, you may need a
IDE card. If you use the secondary IDE card, you should set the DVD-
secondary
ROM drive
are
*
jumper to the master
connecting to the secondary
mode if the DVD-ROM drive is the first device you
IDE card.
When the DVD-ROM drive does not install in OS/2 warp.
(SOLUTION)
1. Select NON-LISTED IDE CD.
*
DVD-ROM drive is not
present in Windows
3.1
or
3.11
or
DOSSHELL.
(SOLUTION)
1. When the WTN
or DOSSHELL command lines are present in your AUTOEXEC.BAT,
make sure that the MSCDEX.EXE command line appears before the WIN or the
DOSSHELL command lines.
E-14
SPECIFICATIONS
Items
General
CD-ROM
Data
553
Capacity
635
Performance
12cm/8cm
Rotational
200-5,100rpm
interface
ATAPI/E-IDE
Supported System
IBM PC-AT
Transfer
3.6
Access
100ms
rate(Sustained)
Time(1/3 Stroke)
4.7
Mbyte (mode 1),
Mbyte (mode 2)
Disc Diameter
Speed
DVD-ROM
or
8.5
Gbyte (DVD-5),
Gbyte (DVD-9)
Compatible
Mbytes/sec (24x max)
2.70
Mbytes/sec (2x)
150ms
MTBF
50,000 Power On Hours (Duty Cycle 10%)
Buffer size
256
Kbytes
Error Rate
ECC
1block/1015 bits
(single), 1 block/1012 bits (24x)
(single), 1 block/109 bits (24x)
2,048 bytes/block (Mode1 & Mode2 Form1)
2,340, 2,336 bytes/block (Mode2)
2,324 bytes/block (Mode2 Form2)
2,352 bytes/block (CD-DA),
2048 bytes/block (DVD)
on
ECC off
1block/1012 bits
User Data/Block
Supported
Audio
Disc
CD-DA, CD-ROM, CD-ROM XA-READY,
Photo-CD, DVD-ROM, CD-R, CD-RW
Dynamic Range
80 dB
S/N Ratio
85 dB
THD
0.05% at 1 KHz
Channel
80 dB at 1KHz
Separation
Headphone Level
Line Output Level
Line Output Jack
Headphone Jack
Environment
+
10%
Power
Ripple<100m Vpp
Requirements
5V
+
:
Specifications
4 Pin
ø
3.5
1.2A
(Maximum)
0.8A
(Maximum)
5%
Ripple<100m Vpp
NOTE
(33Ω)
(47kΩ)
terminal (Rear)
mm (Front)
1.0 Vrms
5~45°C
Temperature
12V
0.70 Vrms
are
subject
to
change
without notice for
E-15
improvement.
Internet Address
http
://
www.
:
LGEservice.com
DVD-ROM LIMITED WARRANTY
LG Electronics U.S.A., Inc. will
repair or at its option replace, without charge, your product which proves to
workmanship under normal use, during the warranty period listed below from
the data of original purchase. This warranty is good only to the original purchaser of the product
during the warranty period as long as it is in the U.S. including Alaska, Hawaii, and U.S. Territories.
be defective in material
or
WARRANTY PERIOD
MODEL #
LABOR
PARTS
1 Year
1 Year
HOW SERVICE IS HANDLED
If the unit is defective,
sent
by 2-day
a
replacement*
will be
air for the first year.
After
one year, repair or a 2-day swap at a
fixed labor charge. For service, please call
1-800-243-0000
(Mon.~Fri.7AM~7PMCST)
No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED
WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO
THE DURATION OF THE EXPRESS WARRANTY HEREIN. LG ELECTRONICS U.S.A., INC.
SHALL NOT BE LIABLE FOR THE LOSS OF THE USE OF THE PRODUCT, INCONVENIENCE,
LOSS OR ANY OTHER DAMAGES, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE
OF, OR INABILITY TO USE, THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY
APPLICABLE TO THIS PRODUCT.
Some states do not allow the exclusion
limitations
or limitation of incidental or consequential damages or
long an implied warranty lasts; so these limitations or exclusions may not apply to
warranty gives you specific legal rights and you may also have other rights which vary
on
how
you. This
from state to state.
THE ABOVE WARRANTY DOES NOT APPLY:
1. To
2.
3.
damages or problems which result from delivery or improper installation.
To damages or problems which result from misuse, abuse, accident, alteration, or incorrect
electrical current or voltage.
To service calls which do not involve defective workmanship or material and explaining the
operation of the unit.
Therefore these costs
are
paid by the
consumer.
CUSTOMER ASSISTANCE NUMBERS:
To Prove
Warranty Coverage:
Retain your Sales Receipt to prove date of purchase.
Copy of your Sales Receipt must be submitted at the time
warranty service is provided.
To Obtain Product, Customer,
or Service Assistance:
Call 1-800-243-0000 24 hrs/7
Push appropriate menu code.
For
Call 1-800-243-0000
Exchange
Service:
Push
*
appropriate
Replacement is a factory-reconditioned unit.
one-year period. Factory-reconditioned units
year warranty expires.
(Mon~Fri8am~5pmCST)
menu
Free
are
days
code.
replacement applies only
available at
a
within the initial
low, fixed cost after the
one-
DRD-820B
English ........Page
E-2
DVD
~
E-15
-
ENHANCE
ROM DRIVE
D
CLASS 1
LASER PRODUCT
KLASSE 1
LASER PRODUKT
LUOKAN 1
LASER LAITE
KLASS 1
LASER APPARAT
Copyrightⓒ
1997 LG Electronics Inc.
LG Electronics USA, Inc.
1000 Sylvan Ave.
Englewood Cliffs,
NJ 07632
LG Electronics U. K. Ltd,
LG House,
264 Bath
Road,
Slough,
Berks. SL1 4DT
LG Electronics Deutschland GmbH
Jakob Kaiser Straße 12
47877 Willich 1
GERMANY
LG Goldstar France SARL
12, RUE LECH WALESA BAT.B
77322 LOGNES MARNE LA
VALLEE CEDEX 2 FRANCH
P/NO
:
3828HM1007F
Printed in Korea
Download PDF