LG | V-5010D | LG V-5010D Owner’s Manual

Vacuum Cleaner
OWNER'S MANUAL
MODEL
:
V-5060CT
(Hose-Button Control, Booster, Telescopic Pipe)
V-5000CT (Hose-Button Control, Telescopic Pipe)
V-5000CD (Hose-Button Control, 2-Steel Pipes)
V-5000HT/V-5004HT (Hose-Slide Control, Telescopic Pipe)
V-5000HD (Hose-Slide Control, 2-Steel pipes)
V-5000T
(Body Slide Control, Telescopic Pipe)
V-5000D
(Body Slide Control, 2-Steel pipes)
V-5010T
(Body-On/Off, Telescopic Pipe)
V-5010D
(Body-On/Off, 2-Steel Pipes)
Please read carefully and thoroughly the operating instructions and
safety precautions before installing and operating your vacuum
cleaner.
P/No.: 3828Fi3698S
Solvent
Red mark
Yellow mark
Dust Indicator
Floor
1
2
-2-
CAUTION
Take
when setting the
dust bag.
care
Flexible Hose
V-5060CT
Button Switch
Control Cover
V-5000CT
V-5060CT
V-5000CD
V-5000CT
V-5000CD
V-5000HT
V-5000T
V-5004HT
Slide Switch
V-5000D
V-5000HD
V-5000HT
Air
V-5004HT
Adjustment
V-5000HD
V-5010T
V-5010D
V-5000T
V-5000D
Extension
Cord rewind button
V-5010T
pipes
Control Cover
V-5010D
Telescopic Pipe
(V-5060CT)
(V-5000CT)
(V-5000HT)
(V-5004HT)
(V-5000T)
(V-5010T)
Steel Pipe
(V-5000CD)
(V-5000HD)
(V-5000D)
(V-5010D)
Plug
Body
Switch
button
Dust indicator
(ON/OFF)
Suction inlet
Castor
Latch
ACCESSORIES
Nozzle
Accessory
holder
Upholstery
-3-
nozzle
Crevice tool
Dusting
brush
IMPORTANT SAFEGUARDS
a
using an electrical appliance, basic safety
precautions should always be followed, to reduce
the risk of fire, electric shock and injury to persons,
including the following:
17 Take electrical
and its coat is
USING THIS APPLIANCE
20 Do not
Disconnect power supply before servicing and/or
the unit. If not, electric shock could occur
1 Do not leave
the outlet when not in
2 Do not
pick
use or
outdoors
use
Unplug
it from
before
3 Do not handle
or
as a
tion is necessary when used
toy. Close
by
1
handle
cord is
damaged,
its service
agent
order to avoid
a
replaced
simi-
or a
hazard.
the cord away from heated
unplug by pulling the
plug, not the cord.
cord. To
1)
unplug,
pick
that is
or
up flammable
liquid or vapors such as gasoline
where they may exist.
13 Do not
Always
15 Do not
Extra
to
pick
use vacuum
fiters in the
14
remove
the HOSE.
pull
2)
cleaner without dust
keep
16 The cord
in
v/cleaner
on
pipes
2 Pieces STEEL PIPES
Do not
pull
Pulling
problems
When
plug
out of the
the cord
rapidly
and
rewinding.
past
cleaning
is
cleaner and
the red mark.
the red mark may
cause
rewinding system.
completed, unplug
5 Press the ON/OFF switch
unplugging.
cord from
(
). (fig.5)
extinguish slowly when press
off position. (V-5060CT, V-
Power indicator will
the chairs, tables, etc.
cleaning stairs.
when
beyond
with the cord
vacuum
(fig.4)
socket outlet and press the cord reel button. The
cord will be automatically rewound.
switch button in
must be taken when
moves
clamp
Adjustment.
insert into the socket outlet.
areas
bag
the hose
TELESCOPIC EXTENSION PIPES
4 Pull the main
smok-
combustible
or use
depress
(V-5000D,V-5010D,
V-5000CD,V-5000HD,)
Insert the STEEL PIPES firmly each other. (fig.1)
right place.
turn off all controls before
care
or
a
out.
the cord out
use
of the v/cleaner until
Push the slider control downwards to extend
ashes.
12 Do not
body
sound is heard.
or/ retract extension
anything
burning
cigarettes, matches, or fireplace
up
as
or
(V-5000CT, V-5000HT, V-5004HT, V-5010T,
V-5000T,V-5060CT) (fig. 3)
Keep hair, loose clothing, fingers, and all parts of
body away from the openings. Do not use vacuum cleaner(v/cleaner) to pick up sharp hard
objects, small toys, pins, etc.
such
the
(fig. 2)
3 EXTENSION PIPES
put any object into openings. Do not use
with any openings blocked; keep free of dust. lint,
hair, and anything that may reduce air flow.
ing,
on
the nozzle, the extension pipes and the
narrow section into the wide sec-
button and
9 Do not
11 Do not
to rest
(fig.1)
To
grasp the
10
heavy objects
insert the
clicking
surfaces.
8 Do not
or
Insert the HOSE into
or
Keep
:
2 HOSE Connection.
a
the cord.
over
it must be
carry by the power cord as a handoor on cord, or pull the cord around
edges or corners. Do not run appliance
pull
dle, close
sharp
Connecting
tion.
by the manufacturer or
larly qualified person in
7 Do not
sharp
USING THE VACUUM CLEANER
atten-
children
manufacturer's recommended attach-
supply
or
use of radio transmitting devices close to the
appliance may interfere the function of the appliance, input power may vary.
ments.
6 If the
solvent in toxic
dry cleaning
with wet hands.
appliance
4 Do not allow it to be used
only
mark.
cause
wet material.
or
plug
for
22 The
wet surfaces. Do not
or on
jobs expected
power cord. If the power cord is damaged
frayed, it may cause a fire or electric shock.
.
up the water
5 Use
in.
use
21 Do not allow
start.
appliance plugged
for those
flammable. It may result in the surface damage.
Wipe off the dirty place with a clean cloth.
cleaning
suddenly
only
cleaner.
vacuum
pull out the cord beyond the red
Pulling the cord out past the red mark may
problems with the cord reel.
WARNING
servicing
home
19 Do not
READ ALL INSTRUCTIONS BEFORE
and/or cleaner could
plug when rewinding
plug to whip when
when hose is cracked
inspection
peeled off.
18 Use this v/cleaner
a
or
and hold the
path
rewinding.
When
ASSEMBLING
clear
onto cord reel. Do not allow the
5000CT/CD)
Provide
-4-
6
the power
Adjusting
9 DUST INDICATOR
1) V-5060CT, V-5000CT, V-5000CD (fig. 6)
GREEN
power with the power control switch in
the handle.
Adjust
Automatic
RED
cleaning mode, this
optimal cleaning is required
appliance sensing the floor condition and
nozzle
mode is used when
by
the
amount of dust
BOOSTER
dirt which is
10
in
deep-embedded
a
or on
automatically.
CAUTION:
(V-5060CT)
MIN
can't
This mode is used for
cleaning at night, or
cleaning required. (V-5000CT/CD)
MAX : This mode is used for cleaning carpets or
similar items which require strong suction force.
OFF : Used to stop appliance operation.
:
power with the
Open
3. Remove the moisture.
in shade for about
1.
2.
over
mark
(fig
(fig.5)
Store
Accessories
two
The crevice tool
the
hook.
on
the
:
a
cool, clean, and dry
:
Push the nozzle holder into
on
the bottom of the v/cleaner.
on
the
rear
of the
v/cleaner.(fig.20)
BEFORE REQUESTING SERVICE
Proper assembly and safe use of your vacuum cleaner
your personal responsibilities. Read this "Owner's
Manual" carefully for important use and safety
For the dust between the ribs of the
DUSTING BRUSH: For
on
or
in the
narrow
gentle vacuuming
information.
gap.
of
Repairs, when necessary, must be performed at an
authorized service facilities. This appliance is intended
a
the furniture, curtain etc.
UPHOLSTERY NOZZLE: For
the
cleaner in
Position
(fig. 21)
be stored at the tool box in
radiator, between the shelves,
on
Micro Filter
are
CREVICE TOOL
dust
vacuum
the holder slot
appliance
delicate fabrics
High Efficiency pleated
Horizontal Position: Push the nozzle holder into
be attached
22.
can
arrow
(fig.19)
be stored in the holder with
can
types, like fig
keeping
it.
the holder slot
8 HOW TO USE THE ATTACHMENTS
using clamping
:
with the
clean EXHAUST FILTER.
Filter.)
place.
Upright
pressure. If the suction
power weakened, raise the front end slightly. (fig.10)
Extention wands
on
18-¥L
Carbon
the floor. Do not exert
can
sufficiently
13 HOW TO STORE THE VACUUM CLEANER
particularly parquet
by applying only light
Holder
the filter
or
V-5004HT, V-5000HD, fig 18-¥M : Micro and
obtained
Accessory
a warm
dish-washer
V-5060CT, V-5000CT, V-5000CD, V-5000HT,
this may damage the flooring,
floors. Best results will be
as
Dry
day.
3. Insert the EXHAUST FILTER
reduced.(fig 8)
lightly
a
a
Open the exhaust cover. (fig 17)
Replace the old EXHAUST FILTER
new one or
7 HOW TO USE NOZZLE
Pass the nozzle
(fig. 16)
12 THE EXHAUST FILTER REPLACEMENT
the air hole in the handle, then suction
excessive pressure,
PHILIPS.
by
soapy water. Do not clean in
in a washing machine.
V-5010D
power will be
genuine LG dust bag. If you
only 'HR6938-OSH' of paper bag
use
use
1. Pull out the MOTOR SAFETY FILTER
3) V-5000T,V-5000D (fig.8,9)
Adjust power with the sliding switch in the body.
(fig.9)
Open the hole in the handle, then suction power
will be reduced.(fig 8)
Press the on/off switch to ON.
Always
2. Shake the dust off and wash filter in
handle.
4) V-5010T,
bag
cleaner off
11 THE MOTOR SAFETY FILTER CLEANING
switch in the
sliding
than 10cm from the floor.
vacuum
get it,
made
is
2) V-5000HT,V-5000HD,V-5004HT (fig.7)
Adjust
bag is full
detaching the
(fig. 5), remove the
by pressing the knob and open the cover by
pressing the latch. (fig. 12)
1) Paper filter bag
Dispose of the bag and set the new one.
2) Cloth filter bag
After sliding the clip off or unzipping the cloth
filter bag, empty the cloth filter bag. (fig. 15)
any bulky obstacles, Power in this mode is
much higher than MAX mode power.
BOOSTER operates for 10seconds and is
when silent
Filter
hose
the floor, and also recommended when the
hose, the pipes, of the nozzle is clogged with
restored to the last mode
use.
bag.
the dust filter
Switch the
removing
carpet
more
Replacing
present.
This mode is suitable for
:
the filter
Watch the dust indicator after
The normal
:
Empty
:
(fig. 11)
Continue to
:
vacuuming
for HOUSEHOLD USE ONLY and not for commercial
of the
or
upholstery.
-5-
industrial
use.
SAVE THESE INSTRUCTIONS
The serial number is found
number is
unique
You should record
this
guide
Date of
Dealer
as a
the bottom of this unit. This
on
to this unit and not available to others.
requested
information here and retain
permanent record of your purchase.
purchase
purchased
from
Dealer address
Dealer
phone
No.
Model No.
Serial No.
TROUBLE SHOOTING CHART
Review this chart to find
WARNING
do-it-yourself
solutions for minor
performance problems.
supply before servicing and/or cleaning
and/or the cleaner could suddenly start.
: Disconnect power
electrical shock could
occur
Possible Cause
Problem
Cleaner won't
1.
run.
Unplugged
at wall outlet.
2. Power control S/W is in
"OFF"
1. Full
Poor suction.
2.
position.
clogged filter bag.
Clogged clean filter.
or
Possible solution
1.
Plug
in
firmly.
2. Push switch button.
3.
Regulate power
1.
Change the filter bag.
Change the clean filter.
Replace hose.
2.
movable
rugs or nozzle
hard.
pushes
control switch.
3.
4.
5. Clean the air passage of
nozzle.
Clogged
nozzle.
cover
open.
5. Close filter
picks
as
3. Hole in hose.
5. Filter
Cleaner
the unit
1. Suction too
strong.
too
-6-
1.
cover.
Regulate power
control lever.
POSSIBLE SVC PARTS LIST
DESCRIPTION
PART NO.
PACKING, SEAL
3920Fi4653A
PACKING, ABSORBING
4i23008B
MOTOR ASS'Y
PACKING, MOTOR MOUNTING
FILTER
4681Fi2373J
127V~60Hz
4681Fi2373B
220V~50/60Hz
3920Fi3675B
ASS'Y, CLOTH
5231Fi2444C
CARRIER, BAG
4840Fi1407B
PACKING, DUST SEAL
3920Fi4718B
LEVER, LEGULATION
4510Fi4665B
BASE, BODY
3040Fi1403B
BUMPER, BODY
4820Fi1401B
FILTER(MECH), MOTOR SAFETY
5231Fi4518C
CORD REEL ASS'Y
FRAME, CASTER
4687Fi1415C
127V~60Hz
4687Fi1415D
220V~50/60Hz
3210FI3670B
ROLLER, CASTER
4i22024M
INLET, HOSE
5236Fi2385A
RING, GUIDE
4350Fi3664A
LATCH
4026Fi3661B
COVER, ACCESSORY
3550Fi2390A
INDICATOR ASSY
3520Fi3475B
BUTTON,
CORD REEL
5020Fi3659C
BUTTON, POWER SWITCH
5020Fi3658D
SWITCH ASSY, PUSH
6601Fi3149B
PWB(PCB) ASSY,
MAIN
COVER, EXHAUST
FILTER
FILTER
6871FX2102C
127V~60Hz
6871FX2081B
220V~50/60Hz
3550Fi1402B
ASS'Y, EXHAUST
5231Fi4504F
NOZZLE ASSY, FLOOR
PIPE
REMARK
2549Fi2393A
ASSY, TELESCOPIC
5201Fi2181C
NOZZLE, UPHOLSTERY
5248Fi2259A
TOOL, CREVICE
5058Fi3462A
BRUSH ASSY, DUST
5202Fi3474A
HOLDER, ACCESSORY
4930Fi2378A
HOSE ASSY, FLEXIBLE
5215Fi1305A
-7-
PRINTED CIRCUIT BOARD
BL
BR
S/W
BR
BR
CORD
P.W.B
REEL
ASS'Y
BK
VR1
BL
PLUG
GY
SERVICE CENTER
For service,
please
Area
contact our authorized service center listed below.
Telephone
Number
Fax. Number
Jeddah
(02)
629 2929 ext. 310
(02)
629 1121
Jeddah
(02)
663 2325 ext. 343
(02)
665 2837
Riyadh
(01)
461 5559
(01)
463 3126
Al-Khobar
(03)
857 2929
(03)
857 7643
-8-
SPECIFICATIONS
223mm
505mm
285mm
?
?
?
?
POWER
:
IEC-1200W
MAX-1400W
CURRENT
:
6A / 9.5A
FREQUENCY
VOLTAGE
:
:
50 / 60Hz
?
CAPACITY A
?
POWER CONTROL
?
CORD LENGTH
?
NET WEIGHT
:
3.5L
:
:
:
BODY SLIDE CONTROL
5/6m
4.8kg
127V / 220V
?NETDIMENSIONS:285x505x223(WxDxH)
?PACKINGDINENSIONS:330x579x328(WxDxH)
?
*
ATTACHMENTS
HOSE .................................................1EA
DUSTING BRUSH ..............................1EA
TELESCOPIC PIPE
CREVICE TOOL .................................1EA
(STEEL PIPE).................................1(2)EA
UPHOLSTERY NOZZLE.....................1EA
NOZZLE ..............................................1EA
ACCESSORY HOLDER......................1EA
These
specifications
are
subject
to
change according
-9-
to the
agent/buyer's request.
Serial Number
How to read Serial Number.
:
There is attached
Example)
a
Serial Number label
on
back side of this
902KB00001
Serial No.
PRODUCT CODE.
MANUFATURED MONTH.
MANUFATURED
YEAR(LAST DIGITAL).
-10-
product.
Download PDF