LG | V-4300HT | LG V-4300HT Owner’s Manual

V-4300D/T/HT/CT
V-4350D/T/HT/CT
V-C4360D/T/HT/CT
V-4300DV/TV/HTV/CTV
V-4350DV/TV/HTV/CTV
V-C4360DV/TV/HTV/CTV
V-4600HTV/V-4300ST/V-4360TV
--2--
15
16
12
18
13
17
14
19
20
22
21
min
max
min
max
25
26
27
23
24
28
31
29
30
--3--
Information for your
safety
Please read all the following information,
which contains important instructions for the
safety, the use and the maintenance of the
appliance.
?
This appliance complies with the following EC
Directives: -73/23/EEC, 93/68/EEC-Low
Voltage Directive-89/336EEC -EMC Directive.
Never allow children to
use
the
appliance
unsupervised.
Do not use the appliance If the mains
lead is damaged or faulty.
If the mains lead is damaged, it must be
replaced by an approved LG Electronics
Service Agent as special tools are
needed to repair it.
Always switch the vaccum cleaner off
before :
changing the dust bag
changing or cleaning the filters.
If no dustbag is inserted, the cover cannot
be closed. Please do not use force!
Do not vacuum flammable or explosive
?
?
substances(liquids
Do not
The fuse cover/carrier must be replaced in
the event of changing the fuse.
The plug must not be used if the fuse
cover/carrier is lost. A replacement cover/
carrier must be obtained from authorised
electrical goods retailers.
The use of radio transmitting devices close
to the appliance may interfere the function
of the appliance, input power may vary.
vacuum
or
gases).
hot ash, embers etc.
nor
Do not vacuum water or other liquids.
When you vacuum with an attachment
appliance that has a rotating brush roller:
do not reach into the running brush
roller.
Important for users in the UK.
The wires in the mains lead of this appliance are
coloured in accordance with the following code:
BROWN live
BLUE-neutral
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
PROCEED AS FOLLOWS:
The wire which is coloured BROWN must be
connected to the terminal which is marked L or
coloured RED.
The wire which is coloured BLUE must be
connected to the terminal which is marked N or
coloured BLACK!
VERY IMPORTANT:
Neither wire is to be connected to the earth
terminal of a 3 pin plug. If a 13 amp plug is fitted,
fit a 13 amp BS 1362 fuse.
If any other type of plug is used, protect with a 15
amp fuse at the distribution board.
For appliances which come with mains lead and
plug moulded on : the plug moulded on to the
cord incorporates a fuse.
For replacement use a 13 amp BS 1362
fuse. Only ASTA approved or certified fuses
should be used.
-
How to Use
Connecting
the flexible hose
Push the end of the head(1) on the flexible
hose(2) into the attachment point on the
vacuum cleaner.
To remove the flexible hose from the
vacuum cleaner, press on the button(3)
situated on the head, then pull upwards.
Assembling
(depending
sharp objects.
?
WARNING!Should it become necessary to
replace the moulded on plug then the
detective plug should be destroyed to avoid
any possible shock hazard that could occur
should such a plug be inserted into a 13
amp socket elsewhere in the house.
on
the tubes
model)
Metal
tube(4)
together the two tubes by twisting slightly.
Telescopic tube (5) [fig. 1]
Hold spring latch (6)
Pull out the tube to required length.
Release spring latch to lock.
?Telescopic tube(5) [fig. 3]
Push spring latch(6) forward.
Pull out tube to required length.
Release spring latch to lock.
Telescopic tube(5) [fig. 2]
Release locking knob(6) (turn clockwise).
Pull out tube to required length.
Turn locking knob anti-clockwise as far as it will go.
Using the cleaning head and Accessory
Nozzles (depending on model) Fit the large
?
-
Fit
?
-
-
-
-
-
-
?
-
-
-
cleaning head onto the end of the tube.
The 2 position head(9) is equipped with a
pedal(10) which allows you to alter its
position according to the type of floor to be
cleaned. Hard floor position(tiles, parquet
floors...). Press on the pedal to lower the
brush.Carpet or rug position. Press on
the pedal to lift the brush up.
If you want to use the brush(7), press the
release pedal(8) lightly and disconnect it
from the cleaning head(9).
?
?
?
--4--
When the brush is to be connected on the
cleaning head, press the release pedal
lightly and connect it.
If your appliance is equipped with an
automatic cleaning head(11) without
pedal, it automatically adapts to the
type of floor to be cleaned.
?
?
Crevice Tool(12)
For vacuuming in those normally inaccessible places i.e. reaching cobwebs, or down
the side of a sofa!
Upholstery Nozzle(13)
For vacuuming upholstery, mattresses,
etc. The thread collectors help to pick up
and
Your
lifting it up until it snaps into place.
appliance is equipped with either a
paper dust bag or a fabric dust bag (25)
(depending on model)
Take hold of the dust bag by the handle
and pull. Seal bag using the flap(26) on
bag cardboard. Remove the bag and throw
?
it away.
To refit a new bag push the cardboard
support of a new bag into the bag mount
(27)until it will go no further.
?
the threads and fluff.
?
Dusting brush(14)
For vacuuming picture
frames furniture
outlines, books and other uneven objects.
How to plug in and use
(depending
Empty
Cleaning
the power level
model)
?The flexible hose handle(17) has a manual
air flow regulator(18) which allows you to
briefly reduce the suction level.
?Electronic power control(19)
Suction capacity increases steplessly up to MAX.
?Electronic power control(20)
on
OFF:Power off MIN: Low power MAX:Full
power.
AUTO: Suction capacity will change automatically
according to the quantity of surface dust.
Park-System(21)
For short breaks
during vacuuming, for
small piece of furniture
example
or a rug, use the[Park system?to support
the flexible hose and cleaning head.
Slide the hook attached to the large cleaning
tool into the slot on the rear of the appliance.
to
move a
?
Carrying
and
storage(22)
When you have switched off and unplugged
the appliance, press on the button (16) to
automatically rewind the cord.
You can move or store your appliance in a
vertical position by sliding the hook on the
large cleaning head into the clip on the
underside of the appliance.
Changing
the dust
above.
it and replace it(28). Do not wash it.
Note: as the appliance is fitted with a safety
device which checks that the bag is in place
you cannot close the lid if the bag is not
fitted correctly.
as
Pull out the mains lead to the desired length
and plug into the socket.
Press button (15) to start the vacuum cleaner.
To stop it press the button (15) again.
Adjusting
If your appliance is fitted with a fabric dust bag follow the same instructions
Changing
the air outlet filters
Depending on the model you have chosen
your appliance is equipped with different
types of filters
: foam filter or electrostatic
filter or anti-odour charcoal filter(30).
To change these filters remove the cover of
the filter compartment(31) situated at the rear
of the appliance, by lifting the little catch.
The foam filter, should be cleaned
regularly by tapping it to remove the dirt.
The electrostatic filter or anti-odor
charcoal filter should be changed regularly
(approximately every 6 bag changes)
?
?
?
What to do if your
does not work
appliance
Check that the appliance is correctly plugged
in and that the electrical socket is working.
bag
The dustbag needs changing when the cleaner
is set to maximum power and the cleaner head
is off the floor but the "bag full" indicator
window(23) is completely coloured red.
Even if the dustbag does not appear to be
full at this stage, it should be changed.
It could be that a great deal of very fine dust
has clogged up the pores of the dust bag.
Turn off the appliance and unplug it.
Open the cover by pressing the hook(24)
the motor filter
The motor filter is situated inside the
appliance between the dust bag and the
motor. Each time that you change the air
outlet filter we advise you to remove the
motor filter(29)and to clean it by tapping to
remove the dirt and then replacing it in the
vacuum cleaner.
What to do when the suction
performance reduces?
?
?
?
?
?
?
--5--
the appliance and unplug it.
Check that the tubes, flexible hose and
cleaning tool are not blocked.
Check that the dust bag is not full.Replace
it if necessary.
Check that the air outlet filter is not
blocked. Replace it if necessary.
Stop
P/No.: 3828Fi2003A
Download PDF

advertising