LG | WF-T13D80EP | LG WF-T13D80EP Owner’s Manual

Washing Machine
OWNER'S MANUAL
MODEL : WF-T13D80EP
WF-T15D81EP
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model name and serial number of the set.
Quote this information to your dealer when you require service.
P/No.: MFL42065445
P
roduct Features
Washer doesn't operate while the lid is open. If the lid is open during the wash,
rinse or spin cycles, the operation stops for safety.
Please close the door slowly because you will get hurt if you close it strongly.
sensors (Option)
The sensor automatically detects the quantity of a Detergent put by a user and the
temperature and the quality of water to make the best washing algorithm for
washing and rinsing, which can give the best washing effect.
Fuzzy Logic Control
A built-in load sensor automatically detects the laundry load and a
microprocessor optimizes washing conditions such as ideal WATER LEVEL and
washing time.
W
O
Advanced technology is built into the Electronic Control System which ensures
the best washing result.
Turbo drum washing (option)
When "Punch + 3" washing wings turn, the washing
tub turns in the opposite direction. This makes the
both sides current of water which improve washperformance by rubbing clothes strongly.
3 Step washing
3 step washing makes the best washing performance with low tangling.
Rubbing
Note
Rubbing and
Shaking
Shaking and
Disentangling
: Be sure to remove the unit from the carton base, otherwise the machine
will not be able to operate properly.
C
ontents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer properly.
Just a little preventive care on your part can save you a great deal of time and money over
the life of your washer.
You will find many answers to common problems in the Troubleshooting section. If you
review our chart of Troubleshooting Tips first, you may not need to call for service at all.
Introduction
Safety Information
Identification of Parts
Function Information
Preparation Before Washing
Use of Water, Detergent, Bleach, Softener, Additives
Special Guide for Stain Removal
Function of each Button
4
7
8
9
10
13
14
Washing Programs
Fuzzy Wash (Normal Wash)
Heavy Wash
Delicates Wash
Wool Wash
Quick Wash
Hand Wash
Eco Save Wash
Wash Only, Rinse/Spin, Spin Only
16
16
16
16
16
18
19
20
Option Programs
Soak Wash
Delay Start (Reservation) Wash
Spin Hold Wash
21
22
23
Custom Program
24
Other Useful Functions
25
Placing and Leveling
26
Connecting Water Supply Hose
27
Connecting Drain Hose
30
Grounding Method
31
Cleaning and Maintenance
32
Common Washing Problems
34
Before Starting to Wash
Installation
Care and Maintenace
Troubleshooting
Troubleshooting
35
Terms of Warranty
Terms of Warranty
36
Specification
Specification
37
4
Introduction
S
afety Information
Read carefully and thoroughly through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
Warning : Failure to comply with the instructions under this
sign may result in major physical injuries or death.
Caution : Failure to comply with the instructions under this
sign may result in minor physical injuries or
damages to the product.
WATER
HEATER
SAFETY
PROPER
INSTALLATION
Warning
• Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.
Caution
• The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break down or
deformation may occur.
• Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may
cause electric shock.
• Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly
causing fire or electric shock.
• Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
5
S
afety Information
Warning
• Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger
explosion or fire.
• Close supervision is necessary if this appliance is used by or near children.
Do not allow children to play on, with, or inside this or any other appliance.
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine
while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
WHEN USING
THE WASHER
Caution
• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.
NOTE : Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
• Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded. Flooded floors
may induce electricity leakage, further resulting in electric shock or fire.
• If, during spinning, opening the lid does not stop the tub within about 15 seconds,
immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into washer while it is moving.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 50°C.
Use of excessively hot water may cause damage to fabrics or cause
leakage of water.
Introduction
YOUR
LAUNDRY
AREA
6
Introduction
S
afety Information
WHEN USING
THE WASHER
Warning
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or
deformation of parts.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
It may ignite or explode.
WHEN NOT
IN USE
Caution
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses; they may need
replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation may
occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless specifically
recommended in this Owner’s Manual, or in published user-repair instructions
that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a
cause for fire or electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire
due to short-circuit .
When you are cleaning the washing machine, do not apply water directly to any
part of the washing machine.
It will cause short circuit and electric shock.
7
Body
HOT WATER SUPPLY
HOSE
Powder detergent
box for delayed
washing/softener additives box
COLD WATER SUPPLY
HOSE
Make sure the water
does not leak.
TUB
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer
or its service agents
or similarly qualified
person in order to
avoid a hazard.
INLET HOLE FOR
BLEACH
FUNCTION SELECTOR
LINT FILTER
Clean regularly to stop
linting on the clothes
load.
WASHING WINGS
Vertical movement of
washing action can be
operated when a sufficient
amount of laundry is
deposited.
Set the proper water level,
an excessive amount of
water may increase
entanglement of laundry.
DRAIN HOSE
Check if the drain hose
is hung up before
operating the
washing machine.
LEVELLING LEGS
Use to level the washing
machine for correct balance
& spin operation.
BASE
Accessories
Inlet hose
or
1 Each for cold and
hot water
Drain hose
Cable tie
Introduction
I
dentification of Parts
Introduction
8
F
unction Information
Our machine provides various washing methods which suits various conditions and
types of laundry.
Different types of laundry washing
Fuzzy Wash (Normal Wash)
Use this Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 16)
Heavy Wash
Use this Program for heavily soiled durable garments e.g. overalls, jeans.
Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 16)
Delicates Wash
Use this program to wash DELICATES and washable laundries. (refer to page 16)
Wool Wash
Delicate clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16)
The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
Before washing your woolens check the care label for the washing instructions.
When washing woolens use a mild Detergent recommended for washing wool.
Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages
(Ensure that the whole article is suitable for machine washing and not just the backing material.)
You may wish to handwash these articles and place them in the machine to spin dry.
Custom Program Wash
This setting allows you to store your CUSTOM wash conditions in the normal cycle memory. (refer to page 24)
Hand Wash
Use this program for load that need pretreatment.
After the prewash of 10 -15 minutes and draining, the washer will run to the nomal wash cycle. (refer to page 18)
Washing according to the condition of laundry
Quick Wash
Quick wash can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 16)
Soak Wash
Soak Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove
dirt and grime.(refer to page 21)
Other washing method
Eco Save
Eco Save is the economical program to minimize water consumption. (refer to page 19)
Delay Start Wash
Delay Start Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly. (refer to page 22)
Wash Only, Rinse / Spin, Spin Only
When the user needs only Wash Only, Rinse / Spin, Spin Only. (refer to page 20)
9
Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and
how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
SOIL (Heavy, Normal, Light)
Separate clothes according to the type and amount of soil.
COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
Lint Producers
Lint Collectors
Terry cloth, Chenille, Towels, Nappies
Synthetics, Corduroy, Permanent Press, Socks
Check before Loading
Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
Pretreat any dirt and stains.
Make sure the clothes are washable in water.
Check the washing instructions.
Remove tissue in pockets.
Pretreatment on stains or heavy soil
Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page 13)
Loading
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size
accordingly. Loosely load clothes no higher than the top row of holes in the
washer tub. To add items after washer has started, press Start button and submerge
additional items. Close the lid and press Start button again to restart.
Light and Large-sized clothing
WARNING
Fire Hazard
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type
of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Do not wash water-proof textilles (Skling outfit, baby's nappy automobile seat covers.)
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length, a net will prevent tangling
during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
Before Starting to Wash
P
reparation Before Washing
Before Starting to Wash
10
U
se of Water, Detergent, Bleach and Softener, Additives
Using Water
Amount of WATER LEVEL
This machine detects the quantity of laundry automatically, then sets the WATER LEVEL.
When you select a wash program, the WATER LEVEL will be shown on the control panel.
The following table shows the amount of water.
When the WATER LEVEL is automatically detected, it may differ depending on the quantity
of laundry even though the same WATER LEVEL is indicated on the control panel.
Water Temperature
The machine sets the appropriate temperature automatically according to the wash program .
You can change the Water Temperature by pressing the WATER TEMP. button.
The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results.
We recommend temperatures of:
- HOT 49~60˚C ...(120-140˚F)
White items, diapers, underclothing and heavily soiled, colorfast items.
- WARM 29~40˚C...(85-105˚F)
Most items
- COLD* 18~24˚C ...(65-75˚F)
Only very bright colors with light soil.
When washing in COLD water additional steps may be needed:
- Adjust Detergent amount and pre-dissolve Detergent in WARM water
- Pretreat spots and stains
- Soak heavily soiled items
- Use appropriate bleach
* Temperature below 18˚C ...(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.
In addition, Detergent manufactures and care labels define COLD water as 26~29˚C...(80-85˚F).
If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.
Note
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown
or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be
necessary for severe cases.
Using Detergent
Detergent
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems.
Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated soap
powders should not be used in your washing machine. When washing woolens remember to use Detergent
suitable for washing woolens.
11
The bleach dispenser automatically dilutes and dispenses
liquid chlorine bleach at the proper time in the wash cycle.
1. Check clothing care labels for special instructions.
2. Measure liquid bleach carefully, following instructions on
the bottle.
Never pour undiluted liquid chlorine bleach directly onto
clothes or into the wash basket.
Do not pour powdered bleach into bleach dispenser.
Avoid overfilling or splashing when adding bleach to the
dispenser. The maximum capacity of the bleach
dispenser is one cup of bleach per wash cycle. Overfilling
could result in early dispensing of bleach.
3. Before starting the washer, pour measured amount of
bleach directly into bleach dispenser. If you prefer to use
powdered bleach, add it into the wash basket directly before
adding clothes.
WARNING!
Do not mix chlorine bleach with ammonia or acids such as vinegar
and/or rust remover. Mixing can produce a toxic gas which may cause death
The manufacturer's recommended amount of undiluted bleach goes into the bleach dispenser. During the
final "Infusor" wash action the bleach is added to the wash load. This ensures performance won't be
diminished. Two sequential flushe through the bleach dispenser completely removes the bleach from the
dispenser. Any residual liquid left in the dispenser at the end of the cycle is water, not bleach. To prevent
self-siphoning of the bleach into the wash basket and damage to your clothes, never add more than the
maximum fill level marked on the dispenser.
Also keep clothes away from the bleach dispenser so they don't absorb any bleach droplets left around
the bleach dispenser.
Using the Dispenser Drawer
The dispenser drawer contains three compartments:
Liquid Fabric Softener
Liquid or Powder Detergent
Liquid Wash Boost Additives
The dispenser automatically dispenses additives at the
proper time in the wash cycle.
1. Slowly open the dispenser drawer by pulling the drawer out
until it stops.
2. After adding laundry products, slowly close the dispenser
drawer. Closing the drawer too quickly could result in early
dispensing of additives.
Avoid overfilling or splashing when adding laundry
products to the dispenser. Doing so could result in early
dispensing of laundry products.
At the end of the cycle, you may see water in the
compartments. This is part of the normal operation of the
washer.
NOTE: Do not use bleach in the dispenser drawer.
Before Starting to Wash
Using the Liquid Bleach Dispenser
Before Starting to Wash
12
U
se of Water, Detergent, Bleach and Softener, Additives
Adding Detergent
Add measured detergent to the detergent
compartment of the dispenser drawer.
Do not exceed the maximum fill line.
Detergent is flushed through the dispenser at
the beginning of the wash phase. Either
powdered or liquid detergent can be used.
Detergent usage may need to be adjusted for
water temperature, water hardness, size and
soil level of the load. Avoid using too much
detergent in your washer, as it can lead to
oversudsing and detergent residue being left
on the clothes.
Adding Fabric Softener
If desired, pour the recommended amount of
liquid fabric softener into the left-hand
compartment. Use only liquid fabric softener.
Dilute with water to the maximum fill line.
Do not exceed the maximum fill line.
Overfilling can cause early dispensing of the
fabric softener, which could stain clothes.
NOTE: Do not pour fabric softener directly
on the wash load. It may stain the
clothes.
Adding Wash Boost Additives
The Wash Boost dispenser may be used to
clean heavily soiled or stained garments more
efficiently.
If desired, place the additives for the wash
Boost setting in the right-hand compartment.
Use only liquid additives.
Do not exceed the maximum fill line to
avoid
Overfilling can cause early dispensing of
presoak additives, which could result in
damaged clothes.
NOTE : Do not pour additives directly on the wash load. It may stain the clothes.
13
pecial Guide for Stain Removal
WARNING
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
Read and comply with all instructions on stain removal products.
Keep stain removal products in their original labeled containers and out of children's reach.
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning
solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.
Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames
For successful stain removal:
Remove stains promptly.
Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
To pretreat stains, use a prewash product, liquid Detergent, or a paste made
from granular Detergent and water.
Use COLD water on unknown stains because HOT water can set stains.
Check care label instructions for treatments to avoid on specific fabrics.
Check for colorfastness by testing stain remover on an inside seam.
Rinse and wash items after stain removal.
Stain Removal
STAIN
Adhesive tape, chewing gum,
rubber cement
Baby formula, dairy products, egg
Beverages (coffee, tea, soda,
juice, alcoholic beverages)
TREATMENT
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or nonflammable
dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains.
Pretreat stain. Wash using COLD water and bleach safe for fabric.
Chocolate
Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid. Hand
wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Collar or cuff soil, cosmetics
Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white fabric
Grass
Grease, oil, tar (butter, fats,
salad dressing, cooking oils, car
grease, motor oils)
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply nonflammable
dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash using hottest water safe for
fabric.
Ink
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured alcohol or
nonflammable dry cleaning fluid.
Mildew, scorch
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.
Mud
Brush off dry mud. Pretreat or soak with product containing enzymes.
Mustard, tomato
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Blood
Candle wax, crayon
Nail polish
Paint, varnish
Rust, brown or yellow
discoloration
Shoe polish
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and nonchlorine
bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
safe for fabric.
Before Starting to Wash
S
Before Starting to Wash
14
F
unction of each Button
POWER BUTTON
Use to turn the power on or off.
Push again and power goes on or off
The power goes off automatically about 10 seconds
after the wash is finished.
Delay Start (Reservation)
BUTTON
Use to set a delayed finishing time.
The time increases when the button is pushed.
The following settings are indicated as the button is
pushed 3
4
5
... 11
12
14
16
...46
48
3 HOUR.
To cancel delay time, turn the power switch off.
(refer to page 22)
Soak, Spin Hold BUTTON
These buttons can be selectable for every
program.
Soak:It gives additional 30 min Soak.
(Except for Wool, Delicate, Rinse/Spin,
Spin Only) (refer to page 21)
Spin Hold: It gives gentle spin instead of
normal spin (Except for Wool, Delicate,
Wash Only) (refer to page 23)
Custom Program
BUTTON
This button allows
you to store a
customized wash
cycle for future
use .
(refer to page 24)
SOIL LEVEL BUTTON
This button allows you to select
the strength of the wash action.
Power option selections light up
in sequence as follows Medium
Heavy Light Medium as
the button is pushed.
This can be selected for any
program, but when washing
Heavy, it starts with Heavy.
Adjustment can be made while
washing.
WASHING CONDITION INDICATOR (OPTION)
• It only operates in FUZZY Program.
• During being detected by the sensor, the LED flashes green, orange and red in turn. And,
after detecting, the LED lights a specific color according to the detecting condition as
follows:
If the current washing condition (Detergent quantity, Water Temperature, water quality,
etc.) is determined as better than the standard one, it optimizes the algorithm to save the
energy by decreasing washing time/strength, and the LED automatically turns to red.
If the current washing condition is determined as worse than the standard one, it
optimizes the algorithm by increasing washing time/strength, and the LED
automatically turns to orange.
If the current washing condition is determined as equal to the standard one, the
algorithm has no change and the LED turns to green.
Note
* For optimizing the washing algorithm, the displaying time may be changed during washing-increased by 8minutes at
maximum and decreased by 4 minutes at maximum.
* If the Detergent quantity is put more than the standard, for increasing the rinsing performance, it automatically adds
rinsing, and the remaining time may be increased.
* The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to the
washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit.
15
Use to select the proper
amount of water in
relation to the weight
and type of laundry.
Controlled
automatically
programs.
BEEPER BUTTON
START/ PAUSE BUTTON
This button allows you to adjust the volume of
the Beeper.
Beeper selection light up in sequence as
High
follows: High Off Low
Use to start or pause the washing
process.
Repeats start and pause by pushing the
button.
PROGRAM
BUTTON
CHILD LOCK FUNCTION
Use to lock or unlock the control
buttons to prevent settings from being
changed by a child.
To lock, push the SOIL LEVEL and
WATER TEMP. buttons
simultaneously and to unlock push
them one more time during the
washing process. (refer to page 25)
WATER TEMP.
BUTTON
Use to select Water (Wash
/Rinse) Temperature.
Pressing the button allows
you to select Cold/Cold
Warm/Cold Hot/Cold
Hot/Warm Warm/Warm
Cold/Cold respectively.
Default setting is Cold/Cold.
Use for selecting wash
program.
This button allows you to
select 10 different programs
for different kinds of
laundry and dirtiness.
Program selections light up
in sequence as follows:
Fuzzy Hand wash
Heavy
Delicates
Wool
Eco Save
Wash Only
Quick Wash
Rinse/Spin Spin only
Fuzzy etc.
Select the desired program
by pressing the button.
* The sensor for a Detergent quantity is designed to detect based on a synthetic Detergent powder. If you put a liquid
one or a natural one or too much bleaching agent, the detecting ability of the sensor may be decreased.
* Even if the water level or the water temperature are changed by the user in FUZZY(Normal) Program,
the sensor will still work. The sensor algorithm may differ according to models.
* The control panel may differ according to different models.
Before Starting to Wash
WATER LEVEL
BUTTON
Washing Programs
16
W
ashing programs
Add
the
laundry
Washing
Programs
Fuzzy Wash
(Normal Wash)
1
Add
the Detergent
2
4
Used for normal loads, this
mode automatically selects
the most appropriate
conditions and completes the
sequence in one operation.
The built-in sensor detects the
size of the load and the ideal
wash power and wash, rinse
and spin times are set
accordingly.
Heavy Wash
The detergent should
be used according to
the instruction of the
detergent manufacture.
1
3
Use HEAVY program when
washing Jeans of different
sizes.
Delicates
1
3
Use this mode when washing
lightly soiled clothes for a
short time. The highly
recommended laundry
amount is under 2.0kg.
2
5
Select the
Delicates
program on
the Control
panel.
1
3
Use this program for washing
delicate fabrics such as
lingerie and woolens. (wash
only “water washable”
clothes)
Before washing your woolens
check the care label for the
washing instructions.
(wash only water washable
clothes)
Quick Wash
5
Select the
Heavy
program on
the Control
panel.
Use this program to wash
items requiring a GENTLE
WASH action. This would
include blouses, nylons and
dress shirts with light soiled.
Wool Wash
2
2
Select the
Wool
program on
the Control
panel.
1
3
2
Select the
Quick Wash
program on
the Control
panel.
5
Use neutral Detergent
appropriate for the
laundry.
When washing woolens
use a mild Detergent
recommended for
washing wool.
5
The detergent should
be used according to
the instruction of the
detergent
manufacture.
17
3
The pulsator rotates for
8 seconds to detect the
laundry load.
Then the WATER
LEVEL
will be shown and
water will be supplied.
5
Water will be
supplied for 2
minutes after the
start of the wash to
supplement the
water the laundry
has absorbed.
Caution & Note
Finish
6
When the wash
program ends, the
buzzer will ring for
10 seconds before
the Power goes off
automatically.
If water is already in the tub, or
putting wet laundry into the tub
before starting will increase the
WATER LEVEL.
With lightweight bulky loads,
WATER LEVEL can be set low.
Changes to Water Temperature
(refer to page 15) and wash level are
possible during operation.
4
6
7
4
6
7
Before starting to wash, make sure that
the laundry is washable.
Washing with HOT water may
damage the laundry.
Ensure that the load is under 2kg.
4
6
7
When setting the WATER LEVEL
manually, do not set to Medium to
prevent damage to laundry.
Washing with HOT water may
damage the laundry .
Ensure that the load is under 2kg.
In order to avoid damage to laundry,
the spin cycle may appear slow. This
also avoids wrinkles and clothing may
still contain some water. This is
normal.
4
6
7
Washing Programs
Close the lid
Washing Programs
18
H
and Wash
After the prewash of 10~15 minutes and draining, the washer will run to
the normal wash cycle.
1
Press the POWER button to turn power on.
2
Press the PROGRAM button to select Hand Wash program.
3
Add the laundry into the washing tub.
4
Press the START/PAUSE button.
5
Add the Detergent and close the lid.
Fabric
Softner
Detergent for
main wash
Additives
Hand Wash (pre wash)
Note
• Hand Wash program takes longer washing time than Fuzzy (Normal) program.
19
Eco Save is the economical program to minimize water consumption.
1 Press the POWER button to turn power on.
2 Press the PROGRAM button to select Eco Save program.
3 Add the laundry into the washing tub.
4 Press the START/PAUSE button.
Left time is displayed.
5 Add the Detergent and close the lid.
When the lid is open the machine will not operate, and an alarm signal will remind you to
close the lid.
Note
Eco Save can handle all types of clothes that the Fuzzy (Normal) course can do.
Washing Programs
E
co Save Wash
Washing Programs
20
W
ash Only, Rinse/Spin, Spin Only
When you only need the Wash, Rinse/Spin or Spin cycles, these can be set manually.
1
Press the POWER button to turn power on.
2
Press the PROGRAM button for desired option.
Wash Only, Rinse/Spin, Spin Only
When you want to only drain, wait until the water in the washing tub drains
completely and then turn off the power
3
Press the WATER LEVEL button. (Except for Spin Only)
Control the water level according to the amount of laundry.
4
Add the laundry into the washing tub.
5
Press the START/PAUSE button.
6
Add the detergent (Except for Spin Only) if required and close the lid.
21
Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty.
Soak mode can be used with Fuzzy, Hand Wash, Heavy, Eco Save, Wash only, Quick Wash
program.
1
Press the POWER button to turn power on.
2
Press the PROGRAM button to select the washing program.
3
Press the Soak button.
4
5
Add the Detergent.
Add the laundry and press the START/PAUSE button.
The WATER LEVEL and be used will be shown
and water will be supplied.
6
Close the lid.
Water will be supplied for 2 minutes after the start
of the wash to supplement the absorbed water by
the laundry.
Finish
When the wash program ends, the buzzer will ring
for 10 seconds before the Power goes off
automatically.
Option Programs
S
oak Wash
Option Programs
22
D
elay Start (Reservation) Wash
Delay Start (Rreservation) Wash is used to delay the finishing time of the operation. The
hours to be delayed can be set by the user accordingly. The time on the display is the
finishing time, not the start time.
1 Press the POWER button to turn power on.
2
Press the PROGRAM button to select the washing program.
Select the program for laundry on the Control panel.
This program will not work in Wool, Delicate and Spin Only
Program.
3
Press the Delay Start (Reservation) button.
The light will ‘ Delay’ turn on and ‘TIME LEFT’
will be
marked.
Press the button repeatedly to set the desired finishing time. For
example, To finish washing in 9 hours from now, by make the number
9:00 pressing the Delay Start (Reservation ) button repeatedly.
(RES.=Delay)
4
Add the Detergent.
5
Add the laundry and press the START/PAUSE button.
When the lid is open the machine will not operate, and an alarm
signal will remind you to close the lid
When you press the START/PAUSE button the light will
blink.
6
Close the lid.
Water will be supplied for 2 minutes after the start of the wash to
supplement the water the laundry has absorbed.
Finish
The washing will be finished according to the delayed time.
Note
Finishing time can be delayed from 3~48 hours. Delaying from 3~12 hours can be done in 1 hour time intervals and
from 12~48 hours in 2 hour time intervals.
If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.
To select water level, water temp. or soil level manually, press the Delay Start (Reservation) button and select the
desired option. Then press the START/PAUSE button.
When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning
program. (The laundry will be wrinkled if left for a long time after spinning.)
23
This Program gives gentle spin instead of normal spin.
1
Press the POWER button to turn power on.
2
Press the PROGRAM button to select the washing program.
3
Press the Spin Hold button to select gentle spin instead of normal spin.
4
Add the laundry into the washing tub.
5
Press the START/PAUSE button.
6
Add the Detergent and close the lid.
Note
To smooth out wrinkles, spin rpm is lower than normal spinng rpm. So the laundry has more moisture than
normal.
Option Programs
S
pin Hold Wash
Option Programs
24
C
1
ustom Program
Custom Program allows you to store a customized wash cycle for future use.
Press the POWER button to turn power on.
2 Press the PROGRAM button to select PROGRAM.
3 Select desired Options.
SOIL LEVEL, WATER TEMP., WATER LEVEL, BEEPER, Soak, Spin Hold.
4 Add the laundry and press the Custom Program button in 3 seconds to store
your Custom wash cycle.
Note
To recall your Custom cycle.
1. Press POWER on.
2. Select the Custom cycle by pressing the Custom Program button.
3. Press the START/PAUSE button. Then the wash cycle starts.
25
Child Lock Function
If you want to lock all the keys to prevent settings from being changed by a child, you can use
the child lock option.
How to Lock
1
Press the POWER button
Turn Power on.
2
Press the START/PAUSE button to start washing.
After all washing conditions are set according to the
manual.
3
Press both the SOIL LEVEL button and the WATER TEMP. button
simultaneously.
During the wash program, all the buttons are locked
until washing is completed or it is child-lock function
is deactivated manually.
How to Unlock
If you want to unlock during wash, press both the SOIL LEVEL and the WATER TEMP. button
simultaneously again.
Note
“
” & the remaining time are alternatively shown on the display while they are locked.
Option Programs
O
ther Useful Functions
26
Installation
P
1
lacing and Leveling
Please ensure that transit restraint has been removed before operating your machine.
Place the machine on a flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2 cm to the
right side and left sides of the machine for ease of
installation.
At the rear, a minimum clearance of 10 cm is
suggested.
more than 10 cm
more
than
2 cm
more than
2 cm
Caution
If the washer is installed on a uneven, weak or tilted floor causing excessive vibration,
spin failure or " UE " error can happen to it.
It must be placed on a firm and level floor to prevent spin failure.
2 Set rear legs
Remove the level and tilt the washer forward (pivot on
front legs) about 4 to 6 inches and gently lower the rear
legs back onto the floor.
This action will set rear leg adjustments to correspond
to front settings.
3 Check that the machine is level
Top view of the machine
Open the lid and look from above to see if it is
same as shown.
4 Leveling the machine
Lift the front of the washing machine and twist the
Adjustable Leg until the surface bubble is placed in the
center.
Lower
Raise
Caution
If the power is supplied from a cord extension set or generator, the cord extension set or electrical
portable outlet device should be positioned so that it is not exposed to splashing or ingress of moisture.
27
C
onnecting Water Supply Hose
Connecting Water Supply Hose to water tap
Normal Type(Normal tap without thread & screw type inlet hose.)
1
Untighten the screw
Rubber packing
Untighten the screw of the connector so that the tap
can be placed in the middle.
screw
Connector
2 Fixing the connector to the tap
Push the upper connector up till the rubber packing
is in tight contact with the tap. Then tighten the 4
screws.
3 Attach the water supply hose securely to the
connector
Push the water supply hose vertically upwards so
that the rubber seal within the hose can adhere
completely to the tap.
Connector
Water
Supply Hose
4 Fixing the connector to the water supply hose
Attach the water supply hose to the connector and
then tighten it by screwing it to the right.
5 Check the connection of water supply hose and the connector
After connecting the hose, open the tap to check for any
water leakage.
If the water leaks, close the tap and start again from step 1.
Note
The washing machine is to be connected to the water mains using new hose-sets and old hose-sets
should not be reused.
Installation
Before connecting the Water Supply Hose to the water tap, check the hose type and then
choose the correct instruction here under.
Note that the Water Supply Hose supplied may vary from country to country, Make sure to
connect the blue inlet hose to the COLD water tap, and the orange inlet hose to the HOT
water tap.
28
Installation
C
onnecting Water Supply Hose
Normal Type (Normal tap without thread & one touch type inlet hose.)
1
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water Supply Hose by
pulling the Pressing Rod and the Pressing Handlre that is
attached to the Water Supply Hose.
Middle
Connector
Fixed Sticker
Pressing Handle
Pressing Rod
Water Supply Hose
2 Loosen the fixed nuts to connect the connector to the tap
Rubber packing
screw
Untighten the screw of the connector so that the
tap can be placed in middle.
Fixed sticker
Note
Guide plate
In case tap is too large.
Rubber packing
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate. Then follow step1.
3 Fixing Connectors to the Tap
Connector
Push the upper connector up till the rubber packing is in
tight contact with the tap. Then tighten the 4 screws.
4 Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper and Middle
Connectors. Tighten the connectors by holding one
connector and twist middle connector to the right.
Connector
Middle
Connector
Fixed sticker
Connector
Middle
Connector
5 Connecting Middle Connector and water Supply Hose
Press down the pressing rod of the Water Supply
Hose whick was separated from middle connector (refer to
Step 1) and then join it to the middle connector.
Pressing rod
Water Supply Hose
6 Check for water leakage
After connecting the hose, open the tap to check for any
water leakage.
If the connection leaks, close the tap and start again from
step 1.
If you skip step 1, water leakage may occur.
Pressing handle
29
C
onnecting Water Supply Hose
Installation
Screw Type
1
Attach the water supply hose to the tap.
Push the water supply hose up so that the rubber packing
within the hose can adhere completely to the tap.
Water
tap
Rubber Packing
Water Supply Hose
2 Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then tighten it
by screwing it to the right.
3 Check water leakage.
After connecting the hose, open the tap to check for any
water leakage.
Connecting Water Supply Hose to the machine
Hot
Cold
Connect the water supply hose to inlet valve of the washing
machine, and then lock it by turning the hose connecting
part.
Check to see if there is a rubber seal inside the connector.
Hose connector
Rubber seal
30
Installation
C
onnecting Drain Hose
Before connecting Drain Hose, check your Drain Hose model and choose the correct
instructions.
How to install the drain hose
1 Fit the end of the drain hose to the outlet of the drain pump and tighten the clamp.
Firmly insert the free end of the drain hose into the drain opening of your
home. Make sure the soft rubber end is completely inside the drain opening.
0.9~1.2m
• If the water valves and drain are built into the wall, fasten the drain hose to one of the water hoses
with the cable tie (ribbed side on inside).
• If your drain is a standpipe, fasten the drain hose to the standpipe with the cable tie provided.
Cable Tie
0.9~1.2m
2
Cable Tie
Note
The discharge height should be approximately 0.9~1.2m from the floor.
31
Earth wire should be connected.
If the earth wire is not connected, there is possible a danger of electric shock caused by the
current leakage .
Grounding Method with Ground insert space Terminal
If the AC current outlet has a ground terminal, then
separate grounding is not required. Note that AC power
outlet configurations may differ from country to
country.
Ground
Terminal
Outlet with ground terminal.
Caution
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional outlets or branch circuits. Check the spercification page of
this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall
outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of
theseconditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by an authorized servicer. Protect the power cord form physical or
machanical abuse, such as being twisted, kinked, pinched, colsed in a door, or walked upon. Pay particular
attention to plugs. wall outlets, and the point where the cord exits the appliance.
Other Grounding Method
Burying Copper Plate
Connect the Ground Wire to a Ground Copper Plate and
bury it more than 75cm in the ground.
Ground Wire
75cm
Ground Copper Plate
Using Ground Wire
Connect the Ground Wire to a the socket provided
exclusively for grounding
Ground
Wire
Using a Short Circuit Breaker
If grounding methods described above are not possible,
a separate circuit breaker should be employed and
installed by a qualified electrician
Short-circuit
breaker
Caution
• To prevent a possible explosion, do not connect ground to a gas pipe.
• Do not connect ground to telephone wires or lightning rods. This may be dangerous during electrical storms.
• Connecting ground to plastic has no effect.
• Ground wires should be connected when an extension cord is used.
Care and Maintenance
G
rounding Method
32
Care and Maintenance
C
leaning and Maintenance
Cold water washing
• If you always use COLD water, we recommend that a WARM or HOT wash be used at a
regular intervals e.g. every 5th wash should be at least a WARM one.
When you have finished
• Turn off taps to prevent the chance of flooding should a hose burst.
• Always unplug the power cord after use.
When water supply into the tub is not clean or the filter is clogged with particles (such as sand), clean the
filter in the inlet valve occasionally.
(The figure of power cord and water tap may vary according to the country)
To Clean the Filter in the Inlet Valve
1
Close the tap before turning off the power.
Select both Hot/Cold and then press the
[START/PAUSE] button to remove water
from the machine completely.
2
Turn off the power before
pulling out the cord.
3
After removing the water supply
hose pull out the filter.
Then use a brush to clean the
filter.
4
Replace the filter after cleaning it.
Caution
Before cleaning the filter, the impurities in the water supply hose should be removed.
To Clean the Lint Filter
1
2
3
4
5
Note
If the lint filter is torn or damaged, purchase a new one from LG service center.
6
33
When there is a fear of freezing
Close the water taps and remove the Water Supply Hose.
Remove the water which remains in the water supply.
Lower the drain hose and drain the water in the bowl and the drain hose by spinning.
If frozen
Remove the water supply hose, and immerse it in HOT water at approx..40˚C.
Pour approx..2 liters of HOT water at approx..40˚C, into the bowl and let it stand for 10 minutes.
Connect the water supply hose to the water tap and confirm that the washing machine performs
the supply and drainage of water.
Wash Inner-Tub
Inlet Hoses
Exterior
Long Vacations
Leave the lid open after washing to allow moisture to evaporate. If you
want to clean the inner-tub use a clean soft cloth dampened with liquid
Detergent, then rinse. (Do not use harsh or gritty cleaners.)
Hoses connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit
surface with sharp objects.
Be sure water supply is shut off at faucets. Drain all water from hoses if
weather will be below freezing.
Cleaning the Inside of your Washer
If you use fabric softener or do regular COLD water washing, it is very important that you
occasionally clean the inside of your washer.
Fill your washer with HOT water.
Add about two cups of a powdered Detergent that contains phosphate.
Let it operate for several minutes.
Stop the washer, open the lid and leave it to soak overnight.
After soaking, drain the washer and run it through a normal cycle.
Products that might damage your washing machine
Concentrated bleaches and diaper sanitizer will cause damage to the paintwork and components of your washer.
Hydrocarbon solvents i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint
(Be careful when washing garments stained with these solvents as they are flammable DO NOT put them in
washer or dryer.)
Some pretreatment sprays or liquids can damage your washer’s control panel.
Use of dyes in your washer may cause staining of the plastic components. The dye will not damage the machine
but we suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in
your washer.
Do not use your washer lid as a work surface.
Care and Maintenance
C
leaning and Maintenance
Troubleshooting
34
C
ommon washing problems
Many washing problems involve poor soil & stain removal, residues of lint and scum, and
fabric damage. For satisfactory washing results, follow these instructions.
WASH PROBLEM
Problema
Possible Causes
Poor soil
removal
Not enough Detergent
Wash Water Temperature
too low.
Overloading the washer
Incorrect wash cycle
Incorrect sorting
Do not pretreat stain.
Use correct amount of Detergent for load size,
amount of soil and water Hardness.
Use WARM or HOT water for normal soil. Different
Water Temperature may be required according to soil
type. (refer to page 10)
Reduce load size.
Wash with Heavy or Soak & Heavy wash cycle for
heavy soiled laundry.
Separate heavily soiled items from lightly soiled
ones.
Pretreat stain and heavy soil according to directions
shown on page 9.
Solutions & Preventive Measures
Blue Stains
Undiluted fabric softener
dispensed directly onto
fabric
Rub the stain with bar soap Wash.
Do not overfill fabric softener dispenser and do not
pour liquid fabric softener directly onto fabric.
See page 12 for more instructions.
Black or gray
marks on
clothes
A buildup caused by the
interaction of fabric softener
and Detergent can flake off
and mark clothes
Not enough Detergent
Keep the recommendations against Scrud(waxy
buildup).
Use correct amount of Detergent for load size,
amount of soil and water Hardness.
Yellow or
brown rust
stains
Iron or manganese in water
supply, water pipes, or
water heater
To restore discolored load of whites, use rust
remover safe for fabric.
Install nonprecipitating water softener or an iron filter
in your water supply system for an ongoing problem.
Before washing, run water for a few minutes to clear
lines.
Lint
Incorrect sorting
Tissues left in pocket
Overloading the washer
Wash lint givers eg towels, flannelette
sheets,separately from lint collectors e.g. synthetic
fabrics and remove tissues in pockets before wash.
See page 9 for sorting and caring before loading.
Do not overload the washer
Residue or
Detergent
Overloading the washer
Undissolved Detergent
Use too much Dtergent
Do not overload the washer.
Some Detergents need to be pre-dissolved, check
the Detergent instructions. Try pre-dissolving the
Detergent.
Increase Water Temperature using HOT water safe
for fabric.
Use proper amount of Detergent.
Holes, tears,
or snags
Incorrect use of chlorine
bleach.
Unfastened zippers, hooks,
buckles
Ribs, tears and broken
threads
Overloading the washer
Degradation of fabric
Never pour chlorine bleach directly on fabric.
See page 11 for adding liquid bleach.
Fasten zippers, hooks, and buckles.
Remove objects in pockets. See page 9 for caring
before loading.
Do not overload the washer.
35
If an abnormal symbol appears in the display window, check the following before asking for service.
Request for the service center or agent in the case of failure or damage except for the following.
This appliance is fitted with a safety function that automatically stops the operation of the washing
machine when it is exposed to heavy disturbance on the mains.
Symptom
Water Supply
Failure
Error Message
Check up
Is the water tap shut off?
Is the water supply cut off?
Is the tap or water supply hose frozen?
Is the water pressure low or is the filter of the
inlet valve clogged with impurities?
Is the Hot hose connected to cold?
Is the Cold hose connected to hot?
If the Washing Machine is working under bad
supply of water , " IE" is on the DISPLAY.
Drainage Failure
Is th drain hose positioned correctly?
Is the drain hose bent or placed too high?
Is the internal part of the hose or drain pump
(only pump model) clogged with impurities?
Check if power has gone off.
Spin Failure
Is the laundry evenly balanced?
Is the washing machine placed on a flat
surface?
Door(Lid) Open
Is the lid closed?
Internal sensing
failure
Please call your nearest LG Electronics service
center for help.
Power failure
Overflow failure
Troubleshooting
T
roubleshooting
Terms of Warranty
36
T
erms of Warranty
What Is Not Covered:
Service trips to your home to teach you how to use the product.
If the product is connected to any voltage other than that shown on the rating plate.
If the fault is caused by accident, neglect, misuse or Act of God.
If the fault is caused by factors other than normal domestic use or use in accordance
with the owner's manual.
Provide instruction on use of product or change the set-up of the product.
If the fault is caused by pests for example, rats or cockroaches etc..
Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
Correcting the installation for example, levelling the product, adjustment of drain.
Normal maintenance which recommended by the owner's manual.
Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
Replace fuses in or correct house wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects
with this appliance.
If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training center,
dormitory
If the product is installed outside the normal service area, any cost of transportation
involved in the repair of the product, or the replacement of a defective part, shall be
borne by the owner.
37
Specification
S
pecification
H
W
D
Model
WF-T13D80EP / WF-T15D81EP
Weight
50kg
Size
685(W) X 720(D) X 1095(H)
Water tap pressure
30-800 kPa(0.3-8.0 kgf/
)
In our continuing effort to improve the quality of our appliances, it may be necessary to make
changes to the appliance without revising this manual.
WF-T13D80EP / WF-T15D81EP
50 kg
685(W) X 720(D) X 1095(H)
30-800 kPa(0.3-8.0 kgf/cm2)
WF-T13D80EP
WF-T15D81EP
Download PDF

advertising