LG | WF-T9510TP | LG WF-T8500PP Owner’s Manual

P
roduct Features
Washer doesn't operate while the lid is open. If the lid is open
nse or spin cycles, the operation stops for safety.
during
the wash,
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer
properly. Just a little preventive care on your part can save you a great deal of time and
Fuzzy logic control
A built-in load
C
ontents
automatically detects the laundry load and a
microprocessor optimizes washing conditions such as ideal water level
and washing time.
sensor
money over the life of your washer. You will find many answers to common problems
in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you
may not need to call for service at all.
Introduction
Advanced
technology is built into
ensures the best washing result.
Turbo drum
When "Punch
the Electronic Control
System
which
Before
to Wash
Information
5
Function Information
6
Preparation Before Washing
7
Use of Water,
8
Washing Programs
models : WF-T
Additional Function
Step washing
washing
makes the best
washing performance with
low
tangling.
Options
Installation
Rubbing and
Shaking
Rubbing
Shaking and
Disentangling
Care and Maintenance
ATTENTION :Be
sure
to remove the unit from the carton
machine will not be able to operate
Bleach and Softener
Guide for Stain Removal
Fuzzy
Wash
properly.
base, otherwise the
Troubleshooting
Terms of
Warranty
Specification
11
12
(Normal Wash)
14
Jean Wash
14
Wool Wash
14
Soak Wash
Economy
3 step
Detergent,
Function of each Button
3"
Speedy
3
4
Identification of Parts
Special
tub turns in the
Applied
Starting
washing (option)
washing wings turn, the washing
opposite direction. This makes the both
sides current of water which improve washperformance by rubbing clothes strongly.
+
Safety
14
Wash
14
Delay Start (Reservation)
Wash
16
Option Washing
17
Other useful Functions
18
Placing
and
Connecting
Water
Connecting
Drain Hose
Grounding
19
Leveling
Supply
Hose
Method
20
23
24
Cleaning
and Maintenance
25
Common
washing problems
27
Troubleshooting
28
Terms of
29
Warranty
Specification
30
4
5
S
afety
information
Read and follow this
safety information carefully.
safety, the information in this manual must be followed to minimize the
shock, or to prevent property damage, personal injury, or loss of life.
For your
Introducin
I
WARNING!
risk of fire
or
dentification of Parts
explosion, electric
Introducin
Save these instructions.
Body
?
WATER HEATER
Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more.
Hydrogen gas can be explosive under these circumstances. If the
hot water has not been used for two weeks or more, prevent the possibility of damage or injury
SAFETY
by turning on all hot water faucets and allowing them to run for several minutes. Do this before
using any electrical appliance which is connected to the hot water system. This simple
procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not
smoke or use an open flame or appliance during this process.
PROPER
?
The base opening must not be obstructed by carpeting when the washing machine is installed on
?
Install or store where it will not be exposed to temperatures below freezing or exposed to the
INSTALLATION
a
carpeted floor.
weather.
?
Properly ground washer to conform with all governing codes and ordinances. Follow details in
?
Must be positioned
Installation Instructions.
YOUR
?
LAUNDRY
AREA
?
THE WASHER
?
?
?
?
?
that the plug is accessible.
Keep the area underneath and around your appliances free of combustible materials such as lint,
paper, rags, chemicals, etc.
Close supervision is necessary if this appliance is used by or near children. Do not allow children
to
WHEN USING
so
play on, with, or inside this or any other appliance.
Use this
appliance only for its intended purpose as described in this Owner's Manual.
Never reach into washer while it is moving. Wait until the machine has completely stopped
before opening the lid.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing
different chemicals can produce a toxic gas which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as wax, oil, paint, gasoline, dry-cleaning solvents,
kerosene, etc.) which may ignite or explode. Do not add these substances to the wash water. Do
not use or place these substances around your washer or dryer during operation.
The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully
follow the garment manufacturer's wash and care instructions.
?
To minimize the possibility of electric
Accessories
Water
supply
hoses
Drain hose
Anti-rat
cover
shock, unplug this appliance from the power supply or
disconnect the washer at the household distribution panel by removing the fuse or switching off
the circuit breaker before attempting any maintenance or cleaning.
NOTE:
Pressing Power button to turn off does NOT disconnect the appliance
or
from the power supply.
WHEN NOT IN
?
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a damaged cord or plug.
?
Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break
or
USE
?
rupture should occur. Check the condition of the fill hoses; they may need replacement after 5
years.
Before discarding a washer, or removing it from service, remove the washer lid to prevent
children from hiding inside.
?
Do not attempt to repair or replace any part of this
appliance unless specifically recommended in
this Owner's Manual, or in published user-repair instructions that you understand and have the
?
skills to carry out.
Do not tamper with controls.
or
1 Each for cold and
hot water
Note
Part
can
be different
according to the model.
or
(option)
6
7
Function
Information
Our machine provides various
types of laundry.
Introducin
Different
methods which suits various conditions and
washing
types of laundry washing
Fuzzy(Normal)
Use this
Preparation
Wash
*
T-shirts.
(refer to page14)
Program for heavily soiled durable garments e.g. overalls, jeans.
heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed.
to
(refer page14)
Thick and
Wool Wash
?
SOIL
?
COLOR (Whites, Lights, Darks)
LINT (Lint producers, Collectors)
(lingerie, wool, etc.)
which may be
easily damaged can be washed.
(refer to page14)
(Heavy, Normal, Light)
Lint Producers
Lint Collectors
Most handknitted garments are
Before washing your woolens check the
Check before
specifically modified to prevent felting when they are machine washed.
not made of machine washable wool and we recommend that you hand wash them
washing instructions.
When washing woolens use a mild detergent recommended for washing wool.
Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and
tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.
(Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to
handwash these articles and place them in the machine to spin dry.
?
care
label for the
?
?
?
Washing according
to the condition of
laundry
Economy
(refer to page14)
can
be selected to wash
lightly
soiled clothes of less than 2.0
kg
in
a
?
Make
?
Check the
?
Remove tissue in
on
stains
or
heavy
soil
Pretreat shirt collars and cuffs with
Use
a
a pre-wash product or liquid detergent when placing them in the washer.
washing treat special stains with bar soaps, liquid detergent or a paste of water and granular detergent.
pretreat soil and stain remover.
and
can
be selected to wash
heavily
Loading
Do not wash fabrics
The water level should just
delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly.
(refer to page16)
option
cover
the clothes.
and
Large-sized clothing
Clothes like downs and woollens
options
can
be selected for
Fuzzy
and Jean
washing program. (refer to page18)
Wash
only Spin, Rinse/Spin, Rinse, Wash/Rinse, Wash, Wash/Rinse/Spin,
Speedy Soak/Wash/Rinse/Spin. (refer to page17)
Fire Hazard
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer
can completely remove oil.
dry anything that has ever had any type
of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
Do not
light weight, large and float easily. Use a nylon net and
laundry floats during the wash cycle, it may
become damaged. Use dissolved detergent to prevent the detergent from clumping.
wash them in
a
are
small amount of water. If the
Long laundry items
nylon nets for long, delicate items. For laundry with long strings or long length a net will prevent
tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
Use
needs
Adjust the load size accordingly.
Loosely load clothes no higher than the top row of holes in the washer tub. To
add items after washer has started, press Start button and submerge additional
items. Close the lid and press Start button again to restart.
Light
WARNING
containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
is used to
wash
longer they are left the harder they are to remove.
(For more detail refer to page11)
method
user
washing instructions.
pockets.
Treat stains AS SOON AS POSSIBLE. The
start Wash
When the
Loading
Pretreat any dirt and stains.
sure the clothes are washable in water.
?
?
Separate clothes according to the type and amount of so
Separate white fabrics from colored fabrics.
Separate lint producers and lint collectors.
pockets to make sure that they are empty. Things such as nails, hairclips, matches,
and keys can damage both your washer and your clothes.
Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
Before
start Wash
Option
?
short time.
Soak Wash
or more
?
?
Speedy Soak Wash is designed to maximize washing performance
soiled laundry with Fuzzy or Jean Program.
(refer to page14)
One
cycle, water temperature and spin speed.
coins,
Pretreatment
Wash
wash
Wash
wash
Check all
pens,
?
Delay
same
Terry cloth, Chenile, Towels, Nappies, Diapers
Synthetics, Corduroy, Permanent Press, Socks
The fibers of machine washable woolens have been
Delay
be washed with the
To get the best results, different fabrics need to be washed in different ways.
?
Delicate clothes
washing
can
Sorting
Use this
Other
a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed.
Look for
Sort clothes into loads that
Jean Wash
Speedy
Washing
Care Labels
Program for everyday washing e.g. sheets, towels,
Economy
Before
,
BeforStaingWsh
8
9
U
BeforStaingWsh
Using
of Water,
se
Detergent,
Bleach and Softener
Water
Amount of Water Level
?
?
This machine detects the
will be shown
on
?
When the water level is
the
same
The amount of
Water
?
of laundry
a
can
change
to the
wash program
appropriate temperature automatically according
the water temperature by pressing the WATER TEMP. button. (refer to page
COLD*
-
-
-
impacts the effectiveness of all laundry additives
29~40°C...(85-105˚F)
18~24°C...(65-75˚F)
items, diapers, underclothing
and
and
12)
therefore, the cleaning
heavily soiled, colorfast items.
Most items
Only very bright colors with light soil.
washing in cold water additional steps may be needed:
Adjust detergent amount and pre-dissolve detergent in warm water
Pretreat spots and stains
Soak heavily soiled items
Use
appropriate bleach
Temperature below 18°C...(65˚F) will not activate laundry additives and may cause lint, residue, poor
cleaning, etc. In addition, detergent manufactures and care labels define cold water as 26~29°C...(80-85˚F).
If the temperature of the water in the tub is too cold for your hands, the detergent will not activate and clean
effectively.
Attention
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown
or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be
necessary for
liquid and concentrated detergents,
follow the recommendations of the
(Jeans
detergent manufacturer.
Note: To check you are using the correct amount of detergent, lift the lid of your machine
about half-way through the wash. There should be a thin layer of foam over the surface of the
means
severe cases.
good, but it does not contribute to cleaning your clothes. No
enough detergent has been used; soil and lint can settle back on the clothes
washing
detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
Attention
Adding the detergent
Open the detergent dispenser and deposit the appropriate
Powder Detergent Box
amount of detergent
()
where you deposit the detergent
Powder Detergent dispenser.
Where you
Some detergents MUST be fully dissolved before
deposit the
adding to your machine to get the best wash results. detergent
Check the instructions on the detergent packet.
If you use powdered detergent it is essential that the required amount be fully dissolved in very hot water
before being added to warm or hot water for the actual wash.
Pre-dissolving detergent in warm water when washing in cold water can improve its performance.
Using Liquid
?
?
?
Detergent
Bleach
Bleach
clothing care label for special instructions and separate the
laundry to be bleached
Dilute liquid chlorine bleach.
Measure the recommended amount of liquid bleach carefully
following instructions on the bottle.
Before starting the washer, pour measured amount of bleach directly
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring.
Check
dispenser
()
Follow the
Use
more
detergent package directions. Using too little detergent is a common cause of laundry problems.
detergent if you have hard water, large loads, greasy or oily soils or lower water temperature.
or
If excess
?
Using Detergent
not
machine.
the
.
When
-
*
WARM
For
foam
-
-
The correct amount of detergent will vary depending on the amount of soil in your clothes
and work cloches may need more detergent, while bath towels usually need less.).
water. Lots of foam may look
temperature
The temperature of the water
-
detergent.
automatically detected, it may differ depending on the quantity of laundry even
on the control panel.
in the diagram is about 40g for concentrated detergent.
The machine sets the
You
(to be used)
water level is indicated
cup
detergent
When you select a wash program the water level and the amount of detergent (to be used) will be
shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated
amount of water.
results. We recommend temperatures of:
White
HOT 49~60°C...(120-140˚F)
?
automatically,
then sets the water
panel.
following table shows the
though
?
quantity
the control
The
?
How much
level and proper amount of detergent.
When you select a wash program, the water level and amount of detergent
?
?
BeforStaingWsh
Using Detergent
Choosing
the
right detergent
We recommend the
of domestic
detergent, (powder, liquid or concentrated). Soap flakes or
should
not
be
used in your washing machine. When washing woolens
granulated soap powders
remember to use detergent suitable for washing woolens.
use
Attention
Never pour undiluted liquid bleach directly onto clothes
This may cause change of color or damage the laundry.
or
into the wash basket.
Do not mix chlorine bleach with ammonia
as
vinegar and/or rust remover. Mixing can reduce
toxic gas which may cause death.
Do not pour powdered bleach into bleach
or
acids such
a
dispenser.
10
11
U
BeforStaingWsh
se
of Water,
Detergent,
Bleach and Softener
Special
Guide for Stain Removal
WARNING
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
Fabric Softener
Using
?
?
Dilute fabric softener with water.
Undiluted fabric softener may result in spots that look like oil
stains.
Softener
dispenser (
?
)
?
?
Measure and add the recommended amount of fabric softener
into the compartment marked with this
Follow manufacturer's direction.
symbol(
?
).
?
or
∀
Fabric softener is automatically
with indication beep.
∀
If you want extra rinse, you must add fabric softener
manually when indication beep rings in the final rinse.
This maximize the fabric softener function.
?
dispensed
Do not overfill. The dispenser hold
Never add more than 35mL.
max
?
in the final rinse
Read and comply with all instructions on stain removal products.
Keep stain removal products in their original labeled containers and out of children's reach.
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents
or other flammable or explosive substances because they give off vapors that could ignite or explode.
Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
For successful stain removal:
?
Remove stains
?
Determine the kind of
stain,
then follow the recommended treatment in the stain
removal chart below.
35mL.
Overfilling
early dispensing of the fabric softener
which could result in stained clothes. A cup with a pouring spout will
?
To pretreat
?
Use cold water
?
Check
?
Check for colorfastness
?
Rinse and wash items after stain removal.
can cause
?
promptly.
help you avoid spilling.
The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes its
effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be manually
put during the time when the washer beeps several times before the final rinse. This function informing
correct time to dispense manually is optionally applied to some models. Please keep it in mind that fabric
softener has to be diluted with water before dispensed and never poured directly on clothes.
stains, use a prewash product, liquid detergent,
granular detergent and water.
care
on
unknown stains because hot water
label instructions for treatments to avoid
by testing
stain
can
on
remover on an
or a
set
paste made from
stains.
specific fabrics.
inside
Follow fabric
seam.
care
label
instructions
Stain Removal
TREATMENT
Adhesive tape,
rubber cement
Attention
Do not mix with
detergent or bleach.
Baby formula, dairy products, egg
Beverages (coffee, tea, soda, juice,
alcoholic beverages)
Never pour fabric softener directly on clothes. It may stain them.
Do not stop the washer during the first spin for timely dispensing.
Option washing is not designed to be used with fabric
Scrud(Waxy
Build
softener
chewing gum,
Blood
dispenser.
Candle wax, crayon
up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
comes into contact with detergent. This build-up is not brought about by a fault in the machine.
Chocolate
If scrud is allowed to build-up in the machine it
smell in your washer.
Dye transfer on white fabric
If you wish to
?
?
?
?
?
use
fabric softener
we
result in stains
on
your clothes
or an
Collar or cuff soil, cosmetics
unpleasant
Grass
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
recommend
motor oils)
Using fabric softener sparingly.
filling the dispenser, do not splash or overfill.
Clean dispenser as soon as the cycle is finished.
Clean your machine regularly. (refer to page 26)
Cold water washing increases the chance of this build-up occurring.
Ink
When
wash e.g. every 5th wash should be at least
?
can
Fabric softener of thinner
build-up.
consistency
Mildew, scorch
Mud
We recommend
a
regular
warm or
a warm one.
is less
likely
to
leave residue
hot
Mustard, tomato
Nail polish
on
the
dispenser
and contribute to
a
Paint, varnish
Rust, brown or yellow
discoloration
Shoe polish
Apply ice. Scrape off excess. Place stain face down on paper towels.
nonflammable dry cleaning fluid.
Use
Saturate with
prewash stain remover or
product containing enzymes to pretreat or soak stains.
Pretreat stain. Wash using cold water and bleach safe for fabric.
Rinse with cold water. Rub with bar soap. Or pretreat
safe for fabric.
or
soak with
product containing enzymes. Wash using bleach
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub detergent into dampened area, Wash using bleach
safe for fabric.
BeforStaingWsh
12
13
F
BeforStaingWsh
Water
unction of each Button
temperature button (option)
Use to select water temperature.
Pressing the button allows you to select
Cold
Warm
(Hot&Cold)
Cold respectively. Default
Time
Water level button
(indication of detergent amount)
?
Hot
?
adjust the water level as required. The appropriate
detergent is shown next to the water level in
the Water-Detergent diagram
Use to
Water level is
Use to start
?
?
automatically selected for fuzzy (normal)
Time left
-
During operation, the remaining time is indicated.
?
Delay Start indication (Reservation) When delay start (reservation)
program is selected, it indicates the finishing time. (RES.=DELAY)
?
Alarm indication -When
amount of
setting is Cold.
-
indicate the
program.
The following
abnormality.
For
occurs,
an error
?
after
open.
settings are indicated as the button is
Medium
Small
pushed Large
Ex-Large
Large
pause the
The power goes off
automatically 10 minutes
message appears to
indicates that the lid is
example,
or
washing process.
Repeats start and pause by
pushing the button.
?
an error
BeforStaingWsh
Start/ Pause button
left, Delay Start (Reservation), Alarm indication
stopping.
AUTO OFF
(Power) button
?
Use to turn the power
off.
?
Push
again
on or
off
?
on or
and power goes
The power goes off
automatically about 10
seconds after the wash is
finished.
Wash
?
?
option button(option)
According to kinds of laundry, soiled extent
or washing habit you can select suitable
wash option manually.
By pressing the button wash option is
changed.
Delay Start (Reservation)
delayed finishing time.
?
Use to set
?
The time increases when the button is
?
The
?
pushed.
following settings are indicated as the button is
...11 12
14
5
16
...46
pushed 3 4
48
?
a
Process button
button
Use to select
Soak,
and
Speedy
Wash, Rinse
Spin functions
delay time,
as
desired.
turn
the power switch off.
The control
from
settings
being changed by a child.
To lock, push the PROCESS
3 step works at
?
?
button
Use for
selecting wash program.
This button allows you to select 4
different programs for different kinds of
laundry and dirtiness.
and
simultaneously
push them one more time during
the washing process.
(refer to page 18)
:
panel may differ according to different models
unlock the control
and to unlock
(refer to page 18)
*
or
Program
PROGRAM buttons
(refer to page 16)
Note
Use to lock
buttons to prevent
3 HOUR.
To cancel
Child lock function
?
program selections light up in sequence
follows: Fuzzy (Normal)
Economy
Jean
Wool
Fuzzy (Normal) etc.
pressing the
Select the desired program by
button.
large and medium water level of Fuzzy
as
and Jean program.
14
15
Washing Programs
WashingProm
Add
the
Washing
Programs
Add
Close the lid
the detergent
laundry
Caution & Note
Finish
Fuzzy Washing
(Normal Wash)
If water is already in the tub, or putting wet
laundry into the tub before starting will
Used for normal loads, this mode
increase the water level.
automatically selects the most
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
Add the appropriate
quantity of detergent as
indicated by the water
level next to
Water Detergent.
Or follow the detergent
manufacturer's
instructions
detects the size of the load and the
ideal wash power and wash, rinse
and spin times are set accordingly
Economy Wash
washing lightly
The pulsator rotates for 8
seconds to detect the
laundry load.
Then the water level and
the amount of detergent to
be used will be shown and
water will be supplied.
Water will be supplied
for 2 minutes after the
start of the wash to
supplement the water
the laundry has
absorbed.
When the wash
program ends, the
buzzer will ring for
10 seconds before
the Power goes off
automatically.
With
lightweight bulky loads, water level
can
be set low.
Changes to water temperature (hot/cold) and
are possible during operation.
(refer to page 12)
wash level
Use this mode when
Select the
soiled clothes for a short time. The
highly recommended
Economy
laundry
program on
the Control
amount is under 2.0kg.
panel.
Add the appropriate
quantity of detergent as
indicated by the water
level next to Water
Detergent.
Or follow the detergent
manufacturer's
instructions
Jean Wash
Use Jean program when washing
Jeans of different sizes
Spread the
jean
evenly in
Select the Jean
program on the
Control panel.
the tub
When
setting the water level manually, do not
prevent damage to laundry.
with
hot
water may damage the
Washing
laundry (Water is set to cold automatically).
Ensure that the load is under 2kg
In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing may still
Wool Wash
set to Medium to
Use this program for washing delicate
fabrics such as lingerie and woolens.
(wash only "water washable" clothes)
Before washing your woolens check
the care label for the washing
Select the
Wool
program on
the Control
instructions.
(wash
panel.
only water washable clothes)
Use neutral detergent
appropriate for the
laundry.
When washing
woolens use a mild
detergent recommended for washing wool.
contain some water. This is normal.
Speedy Soak Wash cannot be selected for the
Wool Wash program.
If wool wash is selected, Gentle Spin will be set
Speedy Soak Wash
automatically.
Speedy Soak
Use this mode to wash normal
heavy clothes
which are excessively dirty.
Speedy Soak mode can be used
with Fuzzy or Jean program.
will not work in
Wool &
clothes or thick and
Economy
Program.
Keep pressing the
Speedy Soak light is
on and then Wash, Rinse, Spin lights are on simultaneously.
Until the washing process is completed, the Speedy Soak light is
on.
PROCESS button until the
The water level and the
amount of detergent to be
used will be shown and
water will be supplied.
WashingProm
17
16D
AditonalFucOps
elay Start (Reservation) Wash
Delay Start (Reservation) Wash is used to delay the finishing time of
The hours to be delayed can be set by the user accordingly.
The time on the display is the finishing time not the start time.
the
operation.
Option Washing
When you
only
need the Wash, Wash/Rinse
or
Rinse
cycles,
these
can
be set
manually
,
1
Press the POWER button to turn power
2
Press the PROGRAM button to select the
1
on.
Press the AUTO OFF
2
washing program.
Wash
Select the program for laundry on the Control panel.
This program will not work in Wool Program.
3
Press the DELAY START
(Reservation) button
be completed.
is to
delayed washing
How to set the
:
delay
It's 7
a.m. now.
4
Add the
detergent.
Add the
laundry
The
3
(RES.=DELAY)
Rinse+Spin
,
Spin only options
Option Washing
Press the WATER LEVEL button, to control the water level according to the
laundry. If you do not choose anything, it is set the Large water
level automatically.
(refer to page 12)
amount of
appropriate quantity of detergent marked next to
Water?Detergent.
the
water level of
an
and press the START/PAUSE button.
When you press the START/PAUSE button the
blink.
6
,
as
When the lid is open the machine will not operate, and
alarm signal will remind you to close the lid
5
Rinse
power.
If
time
,
on.
When you want to only drain, wait until the water in the
washing tub drains completely and then, turn off the
time.
p.m. set the
Wash+Rinse
button to turn power
Press the PROCESS button until above
(refer to p13)
light is on.
to set the time when the
you'd like your wash to finish at 9
in the figure below.
When you push the button the reservation time changes
3E 4E5E...12E 14E 16E...E 48E 3 repeatedly.
Example
,
(Power)
light will
supplied for 2 minutes after the start of the
supplement the water the laundry has absorbed.
4
Add the
5
Press the START/PAUSE button.
6
Add the
laundry
into the
washing
tub.
Water will be
Close the lid.
wash to
Finish
The
washing will be finished according to
the
detergent
and close the lid.
delayed time.
Note
?
?
If the lid is open, the machine will not
work, and
an
alarm
signal will alarm to remind you
to close the
lid.
?
washing program, spinning time, water level or hot/cold manually, press the DELAY START
(RESERVATION) button and select the desired option. Then press the START/PAUSE button.
To select
laundry cannot be taken out immediately after the wash program ends, it is better to omit the
spinning program (The laundry will be wrinkled if left for a long time after spinning.)
When the
.
a Wash, Wash/Rinse or Rinse only option is selected,
completed.
When
is
Note
If you do not
the water will not be drained off after the wash
specify the water level, then Medium will be automatically
If only Rinse is
selected, the process will
start from Water
Supply.
selected.
AditonalFucOps
18
19
O
AditonalFucOps
ther Useful Functions
and
Placing
Please
ensure
Leveling
that transit restraint has been removed before
operating
your machine.
Child Lock Function
If you want to lock all the
child lock
keys to prevent settings from being changed by
a
child,
you
can use
Instal ion
the
option.
How to Lock
1
1
Press the POWER button.
Turn Power
Place the machine
on a
flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2 cm to the
right side and left sides of the machine for ease of
on.
2
Press the START/PAUSE button to start
washing.
After all
3
washing conditions
minimum clearance of 10
a
cm
is
are
set
2cm
more
according to the manual.
simultaneously.
cm
than
suggested.
Press both the PROCESS button and the PROGRAM button
than
2cm
2
During the wash program, all the buttons are locked
until washing is completed or until the child- lock
function is deactivated manually.
and the remaining time will be displayed
alternately in child-lock mode.
"
than 10
more
installation.
At the rear,
more
Check that the machine is level
Open the lid
same as
and look from above to
see
Top
view of the machine
if it is
shown.
"
How to Unlock
If you want to unlock
during wash, press both the PROCESS
and the PROGRAM button
simultaneously
again.
3
Leveling
the machine
Lift the front of the
washing machine and twist
Adjustable Leg
washing machine is
placed evenly.
until the
the
Wash
Option (option)
One
Adjustable legs
options can be selected for Fuzzy and Jean washing program.
Wash program is changed as follows according to selected wash options.
or more
wash
?
Extra Wash: Gives additional 3 min wash
?
Extra Rinse
the Anti-Rat Cover (option) Insert the anti-rat
from the back or front of washing machine and screw it
Installing
:
Gives additional
eg.)
Mute
Gentle
Spin
:
deep
rinse
rinse, you must add fabric softener manually when indication
in the final rinse. This maximize the fabric softener function.
If you want extra
rings
?
one
Gives
cover
to be
firmly fixed
(1pcs)
beep
gentle spin instead of normal spin.
Option
If you want to
use
the
washing machine without alarm signal sounds, press both the
WATER LEVEL and
PROCESS buttons simultaneously.
To make buzzer
time.
work, press both the WATER LEVEL and PROCESS buttons simultaneously one more
Caution
If the power is supplied from a cord extension set or generator, the cord extension set or electrical
portable outlet device should be positioned so that it is not exposed to splashing or ingress of moisture.
21
20C
Instal ion
onnecting
Supply Hose
Before connecting the Water Supply Hose to the water tap, check the hose type and
then choose the correct instruction here under.
Note that the Water Supply Hose supplied may vary from country to country, Make
sure to connect the blue inlet hose to the cold water tap, and the orange inlet hose to
the hot water tap.
Connecting
Water
Normal
1
Water
Supply
Hose to water
Type
the
Untighten
1
Type
Separate
(Normal tap without thread & one touch type inlet hose.)
Middle connector from Water
Supply
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
tap
(Normal tap without thread &
screw
Ho
Middle
ed Sticker
connecto
essing
Handle
essing
Rod
type inlet hose.)
ater
Rubber
screw
Untighten the screw of the connector so
tap can be placed in the middle.
Normal
2
packing
screw
Hose
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
that the
Supply
Rubber
packing
screw
Connector
Fixed sticker
Note
2
Fixing
In
the connector to the tap
tighten
3
Attach the water
Push the water
supply
plate.
hose
securely
supply hose vertically upwards
that the rubber seal within the hose
3
to the
can
4
adhere
Water
the connector to the water
er
supply
it
Fixing Connectors to
the
Tap
Connecto
and Middle Connector
Conne
Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
hose
5
supply hose to the connector and
by screwing it to the right.
screws.
Fixing Upper Connector
Connecting
e
ecto
Fixed
Middle Connector and Water
Supply
pressing rod of the Water Supply
separated from middle connector
and
then join it to the middle
Step1)
sticker
(refer to
supply
was
hose and the connector
After
connecting the hose, open the tap to check
for any water leakage.
If the water leaks, close the tap and start again
Pressing
washing machine is to be connected to the water mains using new hose-sets
Check for water
After
leakage
hose, open the tap to check
connecting
for any water leakage.
If the connection leaks, close the tap and start
the
again from step 1.
skip step 1, water leakage may occur.
If you
Attention
not be reused.
Water
6
from step 1
The
le
Connector
Hose
rod
connector.
Check the connection of water
nector
Press down the
Hose which
5
packing
step1.
Remove the fixed sticker in between the
Hose
Attach the water
tighten
Then follow
tighten the 4
Connector
so
Supply
then
G
large.
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
completely to the tap.
Fixing
too
screws.
connector
4
tap is
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
the 4
case
and old hose-sets should
Supply
Hos
ng handle
Instal ion
22
23
C
Instal ion
Screw
1
Water
onnecting
Supply Hose
Connecting
Before connecting Drain Hose, check your Drain Hose model and choose the correct
instructions.
Type
Pump
Attach the water
Push the water
supply
supply hose up
packing within the hose can
so
hose to the tap.
adhere
completely to
Fit the end of the drain hose to the outlet of the
2
Put the other end of the drain hose over the
tighten the clamp.
tap
Water
supply
drain pump and
Water
Rubber
Connect the water
Instal ion
Model
1
that the rubber
the tap.
2
Drain Hose
Packing
Supply
Hose
standpipe or
wash tub.
hose to the tap.
Connect the water
tighten it by
3
supply hose to the tap and then
screwing it to the right.
Check water
leakage.
After
connecting the hose, open the tap to check
for any water leakage.
Note
Connecting
?
Water
Supply
To prevent siphoning, the drain hose should not extend more than 50 mm from the end of the hose
The discharge height should be approximately 0.9
1.2 m from the floor.
Hose to the machine
~
supply hose to inlet valve of
washing machine, and then lock it by turning
the hose connecting part.
Connect the water
Non-Pump
the
1
Before
Model
connecting
Ensure that the hose
?
Check
to
see
if there is
a
rubber seal inside the
clip
is set
as
indicated here.
Hose connector
connector.
Rubber seal
2
Connect the Elbow Hose
Push the elbow hose toward the
body of the
washing machine.
3
Place the Drain Hose
change the direction of the hose, pull out the
change the direction.
2.
Repeat Step
To
elbow hose and
guide.
24
25
G
CarendMitc
rounding
Method
Earth wire should be connected.
If the earth wire is not connected, there is
caused by the current leakage
possible
a
danger of
electric shock
Cleaning
Cold water
.
?
Grounding
Method with Ground insert space Terminal
If the AC current outlet has
ground terminal, then
separate grounding
required. Note that AC
outlet
power
configurations may differ from country
?
?
Ground Terminal
country
washing
If you
always use cold water, we recommend that a warm or hot wash be used
intervals e.g. every 5th wash should be at least a warm one
Turn off taps to prevent the chance of flooding should
Always unplug the power cord after use.
When water supply into the tub is not clean
filter in the inlet valve occasionally.
round terminal.
Other
Grounding
Method
Burying Copper
bury it
Plate and
a
regular
(The figure of power cord and
water
or
the filter is
a
hose burst.
clogged
with
to the
tap may vary according
particles (such
as
sand),
clean the
country)
To Clean the Filter in the Inlet Valve
Close the tap before turning off the power.
Select both hot/cold and then press the
1
Plate
Connect the Ground Wire
at
When you have finished
a
is not
to
and Maintenance
a
Turn off the power before
pulling out the cord.
4
Replace the filter after cleaning it.
[START/PAUSE] button to remove water
completely.
Ground
Copper
more than 75cm in the ground.
to
2
from the machine
e
After
3
removing the water supply
pull out the filter.
hose
Then
use a
brush to clean the filter.
Caution
Before
Using Ground
cleaning the filter, the impurities in the water supply hose should be removed.
Wire
To Clean the Lint Filter
ground Wire to the socket provided
exclusively for Grounding.
Connect the
1
Pull out the lint filter from
2
Turn the net inside out
the tub in the direction
to clean the filter and
shown below.
rinse
it with
3
Replace- the filter to the
original location. Push the
lip of the filter until a pop
water.
sound
Using
a
Short Circuit Breaker
Note
If grounding methods described above
possible,
employed
a
are
?
not
separate circuit breaker should be
and installed by a qualified electrician
If the lint filter is torn
To Clean the
1
damaged, purchase a new
?
one
from LG service center.
Pump casing (for pump model)
Unfasten 2
back
or
screws
of the
cover.
2
Turn the cap as shown in
diagram and unfasten it.
Remove
Caution
?
is heard
To prevent a possible explosion, do not connect ground to a gas pipe
Do not connect ground to telephone wires or lightning rods. This may be
as
foreign objects
pin, button, coin, etc
3
Reassemble the cap to
the arrow direction and
fasten it.
such
dangerous during electrical
storms
?
Connecting ground to plastic has
?
Ground wires should be connected when
no
effect
an
extension cord is used.
(Bottom view)
(Bottom view)
Caution
?
Check if water leaks after
reassembling. (The
Rubber
ring
is in the
cap)
CarendMitc
27
26
C
CarendMitc
and Maintenance
leaning
Common washing problems
Many washing problems involve poor soil & stain removal, residues of lint and
damage. For satisfactory washing results, follow these
scum, and fabric
instructions.
When there is a fear of
?
?
?
freezing
Problems
Lower the drain hose and drain the water in the bowl and the drain hose
?
?
Poor soil
removal
and immerse it in hot water at approx.. 40˚C.
Pour approx.. 2 liters of hot water at approx.. 40˚C, into the bowl and let it stand for 10 minutes.
Connect the water supply hose to the water tap and confirm that the washing machine performs the
Remove the water
and
Wash Inner-tub
supply hose,
Not
?
Wash water
enough detergent
?
the washer
Overloading
?
Incorrect wash
?
Reduce load size.
?
Wash with Jean
Incorrect
?
Do not
soil type.
Vacations
Be
sure
water
be below
?
?
Blue Stains
supply
freezing.
surface with
?
Black or gray
marks on
clothes
it is very
important that you occasionally clean
?
?
Yellow or
brown rust
stains
A
buildup
caused
by
the
?
interaction of fabric
softener and
detergent
can
flake off and mark clothes
?
Not
enough detergent
?
Iron
or
water
or
manganese in
supply,
water
?
?
?
?
?
?
a
powdered detergent that contains phosphate.
Let it operate for several minutes.
Stop
the
After
Lint
drain the washer and
run
it
through
We do not recommend that you wash clothes
a
normal
?
?
cycle.
might damage your washing
Concentrated bleaches and
Incorrect
sorting
pocket
Overloading the washer
machine
or
detergent
diaper sanitizer will cause damage to
the
paintwork and components
?
Overloading
?
Undissolved
?
Use too
of your washer.
?
Hydrocarbon
(Be
careful when
washer
?
?
solvents i.e.
or
thinners and
lacquer thinners,
washing garments stained with these solvents as they
petrol, paint
or
liquids
can
damage your washer's
can
are
dissolve
the washer
detergent
much detergent
plastic
and blister paint
Do not
use
your washer lid
control
panel.
Holes, tears,
or
?
Use correct amount of detergent for load
To restore discolored load of whites,
Install
nonprecipitating
size,
amount of soil
use
rust
remover
safe
water softener
or an
iron filter in
supply system for an ongoing problem.
Before washing, run water for a few minutes to clear lines.
work surface.
Incorrect
use
of chlorine
?
Unfastened
zippers,
hooks, buckles
Ribs, tears and broken
?
Overloading
Degradation
givers
eg
towels, flannelette sheets, separately
synthetic fabrics and remove tissues
sorting and caring
Do not overload the washer
?
Do not overload the washer.
?
?
detergents need to be pre-dissolved, check the
detergent instructions. Try pre-dissolving the detergent.
Increase water temperature using hot water safe for fabric.
Use proper amount of detergent.
Some
Never pour chlorine bleach
See page 9 for
?
Fasten
?
Remove
threads
?
Wash lint
?
bleach.
snags
?
as a
Keep the recommendations against Scrud(waxy buildup).
(refer to scrud page10.)
pockets
before loading.
?
flammable DO NOT put them in
Use of dyes in your washer may cause staining of the plastic components. The dye will not damage the machine
but we suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in
your washer.
?
etc.
dryer.)
Some pretreatment sprays
instructions.
more
before wash. See page 7 for
?
?
dispenser and do not pour
liquid fabric softener directly onto fabric.
from lint collectors eg
Tissues left in
during this procedure.
Residue
Products that
?
?
washer, open the lid and leave it to soak overnight.
soaking,
Do not overfill fabric softener
your water
Fill your washer with hot water.
Add about two cups of
Rub the stain with bar soap. Wash.
for fabric.
?
?
page 7.
and water hardness.
pipes,
water heater
required according to
(refer to page 8)
See page 10 for
is shut off at faucets. Drain all water from hoses if weather will
regular cold water washing,
onto
fabric
Inside of your Washer
If you use fabric softener or do
the inside of your washer.
Undiluted fabric softener
dispensed directly
amount of
or Speedy Soak & Jean wash cycle for
heavy soiled laundry.
Separate heavily soiled items from lightly soiled ones.
Pretreat stain and heavy soil according to directions shown
on
connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit
sharp objects.
size,
hot water for normal soil.
pretreat stain
?
?
warm or
Different water temperature may be
gritty cleaners.)
Hoses
Exterior
Use
cycle
sorting
Leave the lid open after washing to allow moisture to evaporate. If you want to clean
the inner-tub use a clean soft cloth dampened with liquid detergent, then rinse. (Do
Inlet Hoses
Cleaning the
?
?
Use correct amount of detergent for load
soil and water hardness.
temperature
drainage of water.
not use harsh or
?
?
too low.
supply
Long
Solutions & Preventive Measures
Possible Causes
by spinning.
If frozen
?
Troubleshting
WASH PROBLEM
Close the water taps and remove the Water Supply Hose.
Remove the water which remains in the water supply.
directly on fabric.
adding liquid bleach.
zippers, hooks,
objects
in
and buckles.
pockets.
loading.
the washer
of fabric
?
Do not overload the washer.
See page 7 for
caring before
in
28
29
T
Troubleshting
roubleshooting
Before
calling for service,
Symptom
check the
Error
erms
problem against
TWhat
the list bellows.
Message
Check up
.
.
.
Is the water tap shut off?
Is the water supply cut off ?
Is the tap
or
water
?
?
supply hose frozen
?
Warranty
Is Not Covered:
?
Water Supply
Failure
of
?
trips to your home to teach you how to use the product.
If the product is connected to any voltage other than that shown on the rating plate.
If the fault is caused by accident, neglect, misuse or Act of God.
If the fault is caused by factors other than normal domestic use or use in
Service
accordance with the owner's manual.
.
Is the water pressure low or is the filter of the inlet
valve clogged with impurities?
change the set-up of the product.
If the fault is caused by pests for example, rats or cockroaches etc..
Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
Correcting the installation for example, levelling the product, adjustment of drain.
Normal maintenance which recommended by the owner's manual.
Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
Replace fuses in or correct house wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects
with this appliance.
If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training center,
dormitory)
?
Provide instruction
on use
of product
or
?
.
.
Is the Hot hose connected to cold?
?
Is the Cold hose connected to Hot?
?
?
Drainage
Failure
.
Is the drain hose
.
Is the drain hose bent
.
Is the internal part of the hose
positioned correctly?
or placed too high?
(only pump model) clogged
or
drain pump
with
impurities?
?
?
?
.
Spin
Failure
Check if electric power has gone off.
.
Is the
laundry evenly balanced?
.
Is the
washing machine placed on
.
Is the lid closed?
?
?
a
flat surface?
If the
Door(Lid) Open
Internal sensing
failure
Power failure
Overflow failure
.
Please call your nearest LG Electronics service center
for help.
product is installed outside the normal service area, any cost of transportation
involved in the repair of the product, or the replacement of a defective part, shall be
borne by the owner.
TermsofWanty
30
Specification
WF-T(S,C)550(~2)0(~5)P(P,H,C)
Model
WF-T(S,C)650(~2)0(~5)T(P,H,C)
WF-T(S,C)750(~2)0(~5)T(P,H,C)
WF-T(S,C)750(~1)0(~9)P(P,H,C)
WF-T(S,C)850(~1)0(~9)T(P,H,C)
WF-T(S,C)950(~1)0(~9)T(P,H,C)
WF-T8500PP
540(W)
Size
x
540(D)
x
850(H) WF-T(S,C)5500(~5),T(S,C)6500(~5)
WF-T(S,C)5520(~5),T(S,C)6520(~5)
WF-T(S,C)7500(~5),T(S,C)7520(~5)
540(W) x540(D)
590(W)
x
606(D)
x
x
910(H)
WF-T(S,C)5510(~5),T(S,C)6510(~5)
928(H) WF-T(S,C)7500(~9),T(S,C)8500(~9)
WF-T8500PP
590(W)
x
606(D)
x
958(H) WF-T(S,C)7510(~9),T(S,C)8510(~9)
WF-T(S,C)950(~1)0(~9)T(P,H,C)
Water tab pressure
In
our
to the
30
-
800 kPa (0.3
-
8.0
kgf/cm2)
continuing effort to improve the quality of our appliances,
appliance without revising this manual.
it may be necessary to make
Serial Number
How to read Serial Number.
:There is attached
Example)
a
Serical Number label
on
905KW00001Serial
back side of this
NO.
PRODUCT CODE
MANUFACTURED MONTH
MANUFACTURED YEAR(LAST DIGITAL)
product.
changes
Download PDF

advertising