advertisement
▼
Scroll to page 2
of 26
LG Ceiling Duct-Type Air Conditioner LG OWNER'S MANUAL IMPORTANT Please read through this manual. It contains valuable information about your air conditioner. This manual may help save time and money by explaining proper product maintenance and preventing improper use. PRECAUTIONS Pay close attention to precautions in order to prevent potential hazards and damage from misuse or improper installation. LG is not responsible for any damages caused by misuse of the product. Prior to installation, this air-conditioning unit must be submitted for utility (EN service which 61000-3 approval by the provides electricity Norm.) P/No.: 3828A20167F F Your Records or Write the model and serial numbers here: Model # Serial # 1. 2. Safety Precautions Operating Instructions 3. Care and Maintenance 4. Before you call for service You can find them on a label on the side of each unit. Dealer's Name Date Purchased R ead This Manual Inside you will find many helpful hints on how to and maintain your air conditioner properly. Just preventive care on your part deal of time and money can save over you a a use little great the life of your air conditioner. You'll find many chart of answers to common problems If you review troubleshooting tips. our in the chart of you may not need to call Troubleshooting Tips first, for service at all. CAUTION ? Contact the authorized service technician for or ? ? repair maintenance of this unit. Contact the installer for installation of this unit. The air conditioner is not intended for children or use by young invalids without supervision. ? Young children should be supervised to they do not play with the air conditioner. ? When the power cord is to be replaced, replacement work shall be performed by authorized personnel ensure that only. ? Installation work must be performed in accordance with the national standards by personnel only. wiring authorized Safety Precautions Precautions To prevent injury and property damage, follow these instructions. Incorrect operation due to ignoring instructions by the following symbols. indicated will cause WARNING This symbol shows the CAUTION This symbol indicates the harm possibility or damage, of death possibility of or injury the seriousness of which is serious or injury. damage to property. Never Do This Always Do This Installation precautions WARNING WARNING Do not ? ? install, remove and reinstall the unit by yourself. Improper installation will cause water leakage, electrical shock, or fire. Please consult authorized dealer or specialist for the installation work. Please note fault caused by improper installation is not covered by warranty. Unit must be installed in an easily accessible area. Any additional cost required to hire a special equipment to service the unit will be the responsibility of the customer. WARNING WARNING Do not Do not damage or use an unspecified power cord. ? It will ? If the cause electrical shock ? It may cause electrical shock. ? supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid Do not unit out ? fire. or Plug in the power plug properly. operate switches with wet hands. It will operate a Otherwise, it will electrical shock heat cause or fire due to generation. hazard. or stop the by inserting or pulling the power plug. electrical shock stick, Do not insert your finger or etc. into the air inlet/air Do not expose the skin to cool air directly for a long outlet. time. Since the fan rotates at high This could damage your health. speed, this may cause an injury or damage the unit. When an abnormality (smell of burning, etc) Repair or relocation should not be done by the customer. occurs, stop the air conditioner, and cause fire due to heat or ? generation. ? turn off the breaker. ? If the unit continues to be operated condition, it may fire, trouble, cause a in an abnormal ? etc. In this If this is done in electric case, consult your dealer. correctly, it may cause a fire, shock, injury by dropping of the unit, water leakage, 3 etc. Consult your dealer. CAUTION CAUTION ? Contact the authorized Service technician for ? Contact the installer for installation of this unit. ? The air conditioner is not intended for use repair or maintenance of this unit. children by young or infirm persons without supervision. ? Young children should be supervised to ensure that they do not play with the air conditioner. CAUTION CAUTION Do not clean the air Ventilate well when used When the unit is to be conditioner with water. together with cleaned, switch off, stove, etc. a and turn off the breaker. ? Water may enter the unit and degrade the insulation. It may cause an electric shock. Do not put a pet or plant where it will exposed to direct ? This could injure the ? house An oxygen Do not be or shortage apply an may occur. ? Do not put a pet or plant. ? to direct Do not time in leaving imperfect ? unit and do not put on it. going to long time, turn a It may cause an injury. ? or window In the cooling mode, if it is operated in a room with high humidity (80%r.h. or more) for a long time, water condensed in the air conditioner may drop and may wet and spoil furniture, etc. step onto an It may step on the outdoor anything injury through falling down. cause an Do not unstable bench when or use for special purposes. attaching/detaching the panel. open. ? Do not be used for Do not a long high humidity, e.g. door The unit may drop or fall down and cause an injury. dropping operate for a installation damaged. When the unit is not off the breaker. It may cause combustion. on stand which is ?Itmaycauseafireor air flow. ? it may air flow. stove, etc. exposed high Do not leave insecticide flammable spray. deformation of the cabinet. where is Since the fan rotates at speed during operation, cause an injury. ? It may case an falling down. injury, etc. by ? Do not use It may cause quality, If the supply cord is damaged, it replaced by a special cord or assembly available from the When the air filter is to be removed, do not touch the must be this air conditioner to precision devices, food, animal, plants and art objects. preserve deterioration of etc. Do not insert hands when the air through vanes metal parts of the indoor unit. conditioner is operating. manufacturer of its service agent. ? If will cause electrical shock or ? It may cause an injury. fire. ? It will cause an rotating 4 blower. injury by the Operating Instructions Operating Instructions Name and Function of Remote Controller Remote Controller OPERATION SET TEMP Room Temp Time Timer On Set Operation unit FAN SPEED SUB FUNCTION HI Heater Preheat MED Defrost LO Filter ZONE 1 Out door 1234 Program set Off010305070911131517192123 Time no. 3 Signal receptor 2 5 8 9 10 11 12 13 Timer Cancel Program Week 6 47 Holiday Plasma 15 SET/CLR Hour Min 16 RESET 14 1 17 Operation display Displays the operation 9 Timer Set Button conditions. Used to set the timer when the desired time is obtained. 2 On/Off Button Operation starts when this button is pressed, and 10 Week Button stops when the button is pressed again. Used to set 3 Set Temperature Button Used to set the FAN Used to set the room Used to set air without cooling or Electric Heater time in the Used to set desired fan Used to select the ? of the week. weekly timer operation day and change the Function. Used to set and clear the speed. weekly timer. 15 Room Temperature Checking Button 7 Operation Mode Selection Button ? holiday 14 Set and Clear Button 6 Fan Speed Button ? a Used to set the time of the Button(optional:48/60k Model only) Used to set the Electric Heater. ? weekly timer. 13 Time Set Button heating. 5 of the week. 12 Holiday Button Operation Button Used to circulate day 11 Program Button temperature when the desired temperature is obtained. 4 a Used to check the mode. room temperature. 16 Plasma Air Clean Button(optional) Auto Operation Mode. Cooling Operation Mode. Soft Dry Operation Mode. Heating Operation Mode.(except cooling model) 17 Reset Button Used to set the current time and clear the time. 8 Timer Cancel Button Used to cancel the timer. 5 setting Optional Function WIRELESS REMOTE CONTROLLER ? This air-conditioner is remote equipped with wired remote controller basically. But if you want to have the wireless controller, you pay for it. 1 Remote Controller FAN Operation Button Used to circulate Transmits the Signal transmitter signals to the signal receptor. air without room 2 Cooling Operation 3 Soft cooling heating. or Button Dry Operation Button dehumidify without overcooling. Used to 1 11 4 Heating Operation Button (Heat pump model only) 5 Timer Set Button A/CL 4 10 3 9 5 2 6 7 Used to set the timer when the desired time is obtained. Then the wired remote controller is set up to 24 hours by an hour but the wireless remote controller is set up to 7 hours 6 by an hour. Therefore, if you want to set the wired remote controller. over 7 Fan Speed Button hours, use Used to set the desired fan 7 speed. On/Off Button 8 Operation starts when this button is when the button is 8 Set pressed, and stops pressed again. Temperature Button Used to set the temperature when the desired temperature is obtained 9 Auto Operation Button 10 Plasma Air Clean Button(Optional) 11 Electric Heater Button(Optional: 48/60k Model only) Used to set the Electric Heater. for ? Aim at the ? The remote control ? Be ? Do not ? sure Do not signal receptor on the wired remote controller so as to operate. signal can be received at a distance of up to about 7m. that there are no obstructions between the remote controller and the drop or throw the remote controller. place the remote controller in a location exposed other heat ? CAUTION handling the Remote Controller to direct sunlight, signal receptor. or near the heating unit, or any source. Block a strong light over the signal receptor with a curtain or etc. (ex:electronic quick start, ELBA, inverter type fluorescent lamp) 6 so as to prevent the abnormal operation. Set the Current Time and a 1 Press the ' ' day of the Week button. Hour Each time the button is You pressed, the number is changed from to . set the number of the current hour. can OPERATION SET TEMP FAN SPEED SUB FUNCTION FAN SPEED SUB FUNCTION Hour Time 2 Press the ' ' button. Min Each time the button is You can pressed, the number is increased from to . set the number of the current minute. OPERATION SET TEMP Min Time 3 Press ' Week ' button. Each time the button is You can set the day pressed, a day of the week is shifted from sunday to saturday. of the week. OPERATION Week SET TEMP FAN SPEED SUB FUNCTION Time 4 Press the ' RESET ' button. If you want to reset the current time and a day of the week, click the Reset button. OPERATION RESET 7 SET TEMP FAN SPEED SUB FUNCTION Weekly Programming 1 Press the button. Program The remote controller is displayed like a picture. Then ' Program set OPERATION Program ' ',' SET TEMP Program Time 2 Week ' Press the ' button. button repeatedly until desired mode appears. Week Week For example, 3 Select the time you want. Press if you want Hour or If you press ' 05 ' Using Min button 4 times. Thu, press button, then blinking letter is shown. SET/CLR button, then ' ' shape appears. that five o'clock is reserved. shape means below buttons, you can reserve time. SET/CLR Hou * For example, Min the air-conditioner is on 6,7,8 and 13~22o'clock. OPERATION Time 4 Press the Program button again SET TEMP FAN SPEED SUB FUNCTION 010305070911131517192123 to finish weekly programmining. Program 8 FAN SPEED SUB FUNCTION set 010305070911131517192123 Week Press and '01' is blinked. Holiday Setting If Tuesday is a holiday in this week, you may set a holiday. Program 1 Press the 2 Press the Week button. Program button. Week 3 Select the Tuesday. Press the Holiday OPERATION Holiday button. Then the remote controller will be The outside 4 Press the rectangular Program means button again displayed holiday. to finish ' '. Time holiday setting. SET TEMP on or turn off in several Program hours. Timer 1 Press the Timer button to turn Timer 2 Change on or the timer off. setting until the desired time is set. Hou 3 If you want to cancel the timer setting, press the Cancel button. 9 SUB FUNCTION 010305070911131517192123 Timer Setting(Delay start/Pre-set stop) This function is used to turn FAN SPEED Min Cancel Operation Mode Cooling Mode Cooling Mode Soft Dry Mode Soft Mode Heating Mode Dry Auto Mode (Cooling Model) Auto Mode (Heat Pump Model) Operation Procedure 1st On/Off Button OPERATION SET TEMP Room Temp Time Timer On Set 2nd Operation Operation unit FAN SPEED SUB FUNCTION HI Heater Preheat MED Defrost LO Filter ZONE Out door 1234 Program set Off010305070911131517192123 no. Time 3 Mode Selection Button 1 3rd Room Temperature Setting Button Timer Cancel Program Week Holiday Plasma SET/CLR Hour 4th Indoor Fan Speed Selection Button 10 Min RESET 42 Cooling Operation Mode Press the On/Off Button. 1 Select 2 Cooling Operation. Operation Mode Selection Button. time the button is pressed, the operation Press the Each mode is shifted in the arrow direction. HEAT PUMP MODEL Operation Display OPERATION SET TEMP OPERATION FAN SPEED SET TEMP FAN SPEED OPERATION SET TEMP FAN SPEED HI OPERATION SET TEMP FAN SPEED HI HI LO Soft Cooling Operation Dry Operation Auto Heating Operation Operation COOLING MODEL Operation Display OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED HI SUB FUNCTION HI LO Soft Cooling Operation Set the 3 OPERATION temperature lower than the SET TEMP FAN SPEED SUB FUNCTION HI Set the fan ? The Operation temperature within room a can be set range of 18°C 30°C ~ by1°C. temperature. 4 Auto Dry Operation To raise the Temperature. To lower the Temperature. speed. Operation Display OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED HI MED LO ? Select the fan ? The ? Each time the display speed in three steps- high, low, medium. high fan speed. button is pressed, the fan speed mode is shows 11 shifted. SUB FUNCTION Soft Dry Operation Mode This mode dehumidifies without 1 overcooling. Press the On/Off Button. Select Soft 2 Press the Dry Operation. operation Mode Selection Button. Each time the button is pressed, the mode is shifted in the operation arrow direction. HEAT PUMP MODEL Operation Display OPERATION SET TEMP OPERATION FAN SPEED SET TEMP FAN SPEED OPERATION SET TEMP HI FAN SPEED OPERATION SET TEMP FAN SPEED HI HI LO Soft Cooling Operation Dry Operation Heating Operation Auto Operation COOLING MODEL Operation Display OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION HI SET TEMP FAN SPEED SUB FUNCTION HI LO Cooling Operation During 3 ? Soft Auto Dry Operation Operation Dry Operation. The indoor fan impossible Soft speed is because it's automatically already being set to the low, set to the best Control. 12 so the shift of the indoor fan speed for Dry Operation by speed Micom is Heating Operation Mode (Heat pump model only) 1 2 Press the On/Off Button. Select Heating Operation. Press the Operation Mode Selection Button. Each time the button is pressed, the mode is shifted in the operation arrow direction. Operation Display OPERATION SET TEMP OPERATION FAN SPEED SET TEMP FAN SPEED OPERATION SET TEMP FAN SPEED HI OPERATION SET TEMP FAN SPEED HI HI LO Soft Cooling Operation 3 Set the Dry Operation ? temperature. OPERATION SET TEMP FAN SPEED Auto Heating Operation The temperature range of 16˚C SUB FUNCTION can 30˚C ~ Operation be set within by a 1˚C. HI 4 Set the fan To raise the Temperature. To lower the Temperature. speed. Operation Display OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED SUB FUNCTION HI MED LO ? Select the fan ? The ? Each time the display speed in three steps high, low, medium. high fan speed button is pressed, the fan speed mode is shifted. - shows OPERATION 5 SET TEMP This air-conditioner is set to the hot start control in FAN SPEED SUB FUNCTION HI Preheat order not to discharge the cold air during the heating operation. This time, the remote controller indicates 'Preheat'. OPERATION If the outdoor temperature is 6 heating operation, too low during the this air-conditioner is set to the defrosting operation and the remote controller indicates 'Defrost'. 13 SET TEMP FAN SPEED SUB FUNCTION HI Defrost Auto Operation Mode Press the On/Off Button. 1 2 To select Auto Operation, press the Operation Mode Selection button. pressed, the operation mode is shifted in the direction Each time the button is of the arrow. HEAT PUMP MODEL Operation Display OPERATION SET TEMP OPERATION FAN SPEED SET TEMP FAN SPEED OPERATION SET TEMP HI FAN SPEED OPERATION SET TEMP FAN SPEED HI HI LO Soft Cooling Operation Dry Operation Auto Heating Operation Operation COOLING MODEL Operation Display OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED SUB FUNCTION OPERATION SET TEMP FAN SPEED HI SUB FUNCTION HI LO Soft Cooling Operation 3 HEAT PUMP MODEL SET TEMP Operation Set the The OPERATION Auto Dry Operation FAN SPEED temperature lower than the room themperature. temperature can be set within a range of 18˚C 30˚C by 1˚C. ~ SUB FUNCTION HI To raise the Temperature. To lower the Temperature. Set the COOLING MODEL OPERATION SET TEMP The FAN SPEED temperature upper or lower than the standard temperature. temperature can be set within a range of -2 2 by 1 level. ~ SUB FUNCTION HI Cold Cool Proper Warm To raise the (When (This To lower the indication will be shifted to the initial Auto Mode Display state after 4 you feel Hot Temperature. too cool or cold.) (When seconds.) Temperature. warm or hot.) you feel too During Auto Operation: You can The system will automatically switch from the cooling mode and set switch the indoor fan temperature.(Heat speed. pump model only) 14 to the heating mode as the room temperature FAN Operation Press the On/Off Button. 1 2 3 Press FAN Operation Button. Each time Indoor Fan Speed arrow button is pressed, the fan speed mode is shifted in the direction. OPERATION SET TEMP FAN SPEED SUB FUNCTION ? Fan speed is SUB FUNCTION ? Fan speed is low. SUB FUNCTION ? Fan speed is medium. HI OPERATION SET TEMP FAN SPEED high. LO OPERATION SET TEMP FAN SPEED MED * You can't set the temperature in Fan Operation mode. To exit this mode, press 'Operation Mode' button. 15 Electric Heater Operation Mode(Optional: 48/60k Model Only) 1 2 Press the On/Off Button. Select E/heater heating+ Press the Operation. Operation Mode Selection Button. Operation Button on the remote controller.(When the unit operates in heating mode.) Press the Heater OPERATION SET TEMP FAN SPEED HI 3 SUB FUNCTION Heater Set the The temperature upper than the room temperature. temperature can be set within a range of 16°C~30°Cby 1°C. OPERATION SET TEMP FAN SPEED HI 4 Set the Fan To raise the Temperature. To lower the Temperature. SUB FUNCTION Heater Speed. ? Each time the Button is shifted. 16 pressed, the Fan Speed mode is PLASMA Purification Operation (Optional) 1 OPERATION SET TEMP FAN SPEED Press the On/Off button. The unit will start. 2 SUB FUNCTION HI Open the door on Press the PLASMA On/OFF button. Operation will and Timer Cancel Program Week 3 start when the button is New Fan speed speed Min can be set after opening the can select the in three Each time the Plasma steps-low, medium or high. button is pressed, the fan speed mode is shifted. Air purifying operation (PLASMA) is available during cooling, heating or any other operations. SET/CLR Hour pressed stop when the button is pressed again. door of the remote control. You fan Holiday Plasma the remote control. RESET Child Lock Function This is the Function that any children cannot used to the air-conditioner. OPERATION SET TEMP Operation procedure 1 To set the Child-Lock Function Press the Timer button and Minute Set button for three seconds. Then the operation display. mode shift to child lock mode and it is When you press any button in this any selected mode and the 'CL' is three seconds. But the Room time, the displayed 'CL' in the operation remote controller is not converted to displayed in the remote controller for about Temperature function is operated in spite of child Timer ogram Cancel Week Plasma lock mode. Hour 2 To cancel the Child-Lock Function Press the Timer button and Minute Set button for three seconds. Then the child-lock mode is cancelled and the preselected mode is displayed remote controller. 17 in the Holiday SET/CLR Min SET FAN SPEED SUB FUNCTION Telephone Control Operation(optional) Calling from outside, you can start the air conditioner to keep the room comfortable. Even though you went out with the air conditioner on, you can turn it off using the phone 1. With a normal telephone machine. 1 TURN ON 1 outside. Dial the number which is connected with the air conditioner. 2 3 ON ON 2 After ringing 5 times. You can off), then press "0" "0" "7" "8" hear the "Beep" sound (if the air conditioner accordingly. 4 With the sound 5 Hang 1 Dial the number which is connected with the air conditioner. 2 After up the "Beep, Beep" the air conditioner starts OFF OFF phone. ringing 5 times. You can on), then press "0" "0" "7" "9" hear the 4 With the sound 5 Hang up the "Beep Beep" sound (if the air conditioner accordingly. "Beep---" the air conditioner is turned off. phone. Note: product works If internal If on. TURN OFF 3 This is user user doesn't after telephone rings picks up the push the If it is connected phone telephone through EPABX 5 times. before 5 rings, Telephone control button 25 seconds after system, Tele control doesn't work. 18 function does not work. beep, Telephone control function doesn't work. is Telephone Control Operation(optional) 2. With a ARS telephone machine(with auto-answering function) In advance the user need to operate that ARS should work after ringing TURN ON 1 4 times. Dial the number which is connected with air 1 conditioner. After 2 ringing 4 times, "Beep" sound answering machine. and OGM sound from the ON ON 3 Press "0" "0" "7" "8" 4 With the sound 5 2 TURN OFF starts on. Hang up the accordingly. "Beep, Beep" the air conditioner phone. Dial the number which is connected with air 1 conditioner. After 2 ringing 4 times. "Beep" sound answering machine. and OGM sound from the OFF OFF 3 Press "0" "0" "7" "9" 4 With the sound accordingly. "Beep---" the air conditioner is turned off. 5 Hang up the phone. Note: The numbers of response bell should be adjusted to four times if pressing "Out-off-office" button other action for automatic response. The recording time of OGM If it is connected to (Outgoing Message) key phone, should be less than it cannot be worked. 19 approximately 15 seconds. or taking Operation Details ? Cooling Operation When the Mode set temperature, it operates in cooling mode at the set temperature, the set fan speed, and then it will be in automatically turn off when the room temperature reaches the set temperature +0.5°C. room temperature is higher than the ROOM TEMP. More 3 minutes OPERATION START SET TEMP. +0.5°C) OPERATION STOP SET TEMP. -0.5°C) INDOOR FAN OUTDOOR FAN/COMP : SETTING FAN SPEED Helpful : LOW COOL OPERATION :COMPON :COMPOFF information Airflow speed and cooling capacity. The cooling capacity indicated in the specification is the value when the fan speed is set to high, and the capacity will be lower at low or medium fan speed. High fan speed is recommended when you wish to cool the room quickly. ? High Speed After main power is on, Fan will start 7 seconds later. Self-Diagnosis Function 'CH' will flash in the remote controller display when a problem occurs. 20 Then please contact your dealer. Care and Care and maintenance maintenance Caution: Before performing any maintenance, turn off the main power to the system. Indoor Unit Grille, Case, Never and Remote Control Turn the system off before cleaning. To clean, wipe with a soft, dry cloth. Do not use bleach or use any of the followings: Water hotter than 40°C ? Could cause deformation and/or discoloration. abrasives. Note: Volatile substances ? Supply power must be disconnected cleaning the indoor unit. Could before damage the surfaces of the air conditioner. SINNER SCOURING CLBARGER Benzene Air filters 1 Air outlet vent Air Filter Clean the filter with ? The air filters behind Indoor unit suction (the once should be checked and cleaned side) every 2 weeks or more ? often if necessary. a vacuum or warm, soapy water. If very dirty, wash with a solution of detergent in lukewarm water. If hot water (50°C or more) is used, filter may be deformed. 2 After 3 Re-install the air filter. washing with water, dry well in the shade. Air outlet vent PLASMA Filter (Optional) The PLASMA filter should be checked and once every month or more cleaned, often, if necessary. 1 After removing the Cleaner Bracket Panel-Cover, draw the Air slightly sideward to remove the PLASMA filter. 2 Air Inlet Vent PLASMA Filter 3 4 5 Don't touch this PLASMA Filter within 10 seconds after drawing Bracket, it may out Air Cleaner cause an electric shock. 21 Dip mild the PLASMA filter into the water mixed with detergent, for 20~30minutes. Dry the PLASMA filter in the shade for a day. (Especially, the humidity must be removed perfectly from this parts). Be careful not to cut the electric while discharge washing. Re-install the PLASMA filter to the position. original lines Outdoor Unit The heat exchanger coils and panel vents of the regularly. If clogged exchanger and panel vents outdoor unit should be checked with dirt or may be professionally soot, the heat steam cleaned. (Side) (Rear) Air intake vents Note: Dirty or clogged coils will reduce the operating efficiency of the system and cause higher operating costs. Piping Air outlet vents (Side) (Rear) Air intake vents Air outlet vents Piping 22 When the air conditioner is not going to be used for a When it is not a 1 going to be long time. When the air conditioner is to used for be used Operate the air conditioner on Air circulation mode (Refer to page 15) for 2 to 3 hours. This will ? 2 dry out the internal long time. again. Check that the air inlet and outlet of the indoor/outdoor unit are not blocked. parts. Turn off the circuit breaker. Helpful CAUTION CAUTION Turn off the circuit breaker when the air conditioner is not going to be used for a Dirt may collect and may long time. cause a information The air filters and your electiric bill. If the air filters become clogged with cooling capacity will drop, electricity used to operate fire. dust, the and 6% of the the air conditioner will be wasted. Operation Tips Do not overcool the room. blinds Keep or This is not good for the health electricity. and wastes room when the air conditioner is in operation. Avoid regularly. Ventilate the room occasionally. Blockages in the air filter reduce the airflow and lower cooling and dehumidifying effects. Clean at least once Since windows closed, it is a are good kept idea to open them and ventilate the room now and then. every two weeks. 23 that the doors opening windows to as keep the room. Clean the air filter sure and windows Do not let direct sunshine enter the Make curtains closed. are shut tight. doors and much as possible cool air in the Troubleshooting Tips Before you call for service... Troubleshooting Tips! Save time and money! Check the following points before requesting repairs service.... If the malfunction or persist, please contact your dealer. Case See page Explanation The air conditioner does not operate. ? Have you made a ? On first the indoor unit starting, mistake in timer 9 operation? operates in fifteen seconds. ? Has the fuse blown has the circuit breaker or - been The room has peculiar odor. a ? tripped? Check that this is not the a smell exuded damp walls, carpet, furniture or by cloth items in the - room. It seems leaking that condensate is ? Air conditioner does not operate for about 3 minutes when restart. Condensation occurs when the airflow from the air conditioner cools the from the air Conditioner. warm room ? This is the ? Wait about three minutes and - air. protector of the mechanism. operation will - begin. Does not cool or heat effectively. ? Is the air filter dirty? See air filter cleaning 21 instructions. ? The may have been very hot when the air conditioner was first turned on. Allow room room time for it to cool down. ? ? Has the setting temperature incorrectly? been set Are the indoor unit's air inlet or 11, 13 outlet vents - obstructed? The air conditioner operation is ? noisy. For a noise that sounds like water -This is the sound of freon flowing flowing. inside the air conditioner unit. ? For a noise that sounds like the releasing into compressed air - atmosphere. -This is the sound of the being processed dehumidifying water conditioning inside the air unit. Crack sound is heard. Remote control no display display ? is faint, or ? This sound is generated by the expansion/contraction of the inlet grille, to changes of temperature. Has the circuit breaker been etc. due tripped? - at all. NOTE WATER RESISTANT: The outdoor side of this appliance is WATER RESISTANT. The indoor side is not water resistant and should not be water. 24 exposed to excess Product Specifications Details of LG serial No. 1 2345 Code Detail 1 Year 67 Code of Model (Digit) Month 2,3 Nation 4 01~12 Month (Digit) ex) A~Z Product of year 7, 2000 digit 1997 ex) March 0 03, August A~Z ex) K Korea, C ex) A Airconditioner Serial No. 0~9 Production PART NAME 1 COMPRESSOR 2 MOTOR 3 MAIN PCB ASSY 4 REMOCON 5 TRANSFORMER China (Alphabet) 6~10 NO 08 Where manufactured (Alphabet) 5 Meaning The last 0~9 Main Service Part List 891 0 Quantity (Digit) H. G. IBRAHIM SHAKER COMPANY, LTD. SERVICE CENTER * JEDDAH P. O. BOX 50, JEDDAH 21411 KINGDOM OF SAUDI ARABIA TEL NO. * RIYADH * AL-KHOBAR : 6422952 / 6425527 P. O. BOX 15, RIYADH 11411 KINGDOM OF SAUDI ARABIA TEL NO. : 4020570 P. O. BOX 78, AL-KHOBAR 31952 KINGDOM OF SAUDI ARABIA TEL NO. : 8943714 Memo
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project