LG | GR-762DEQF | Owner's Manual | LG GR-892DEQF Owner’s Manual

LG GR-892DEQF Owner’s Manual
REFRIGERATORFREEZER
OWNER'S MANUAL
PLEASE
READ THIS OWNER'S MANUAL THOROUGHLY
BEFORE OPERATING AND KEEP IT HANDY
FOR REFERENCE AT ALL TIMES.
762-3828JD8157J
MORE FRESH
WITH
FOCUSED COOLING
SYSTEM
CONTENTS
LG Refrigerator
INSTALLATION ................................................. 3
INNER PARTS ................................................... 4
OPERATIONS ................................................... 5
Starting
Display panel & Function Buttons
Door Alarm
Self Test
Focused Cooling
Super Ice Making System
Super Cool
Super Freeze
Temperature Control
Ice Making
Fresh meat
Defrosting
Deodorizer(Optional)
Water Dispenser(Optional)
SUGGESTIONS ON FOOD STORAGE .......... 13
CLEANING ...................................................... 14
GENERAL INFORMATION ............................. 14
LAMP REPLACEMENT .................................. 15
IMPORTANT WARNINGS ............................... 15
BEFORE CALLING FOR SERVICE ............... 16
2
INSTALLATION
SELECT A GOOD LOCATION
NEXT
1. Place your refrigerator where it is easy to use.
1. Wipe off all dust accumulated during shipping
and clean your refrigerator thoroughly.
2. Avoid placing the refrigerator near heat sources,
direct sunlight or moisture.
2. Install accessories such as the ice cube box,
cover evaporating tray, etc., in their proper
places. They are packed together to prevent
possible damage during shipping.
3. To ensure proper air circulation around the
fridge -freezer, please maintain sufficient space
on both the sides as well as top and maintain at
least 2 inches (5 cm) from the rear wall.
3. Connect the power supply cord (or plug) to the
outlet. Don't double up with other appliances
on the same outlet.
4. Prior to use, let the refrigerator run for 2-3
hours.
Check the flow of cold air in the freezer compartment to ensure proper cooling has taken
place.
Your refrigerator is now ready for use.
Clearance
more than
5cm
4. To avoid vibrations, the refrigerator must be
leveled.
If necessary, adjust the leveling screw(s) to
compensate for unevenness of the floor.
To make closing the doors easily, the front
should be slightly higher than the rear.
Leveling screw(s) can be turned easily by
tipping the cabinet slightly.
Turn the leveling screw(s) clockwise to raise the
refrigerator, counterclockwise to lower it.
5. Don't install this appliance below 5˚C.
It may cause the debasement of the refrigerator.
3
INNER PARTS
FREEZER
COMPARTMENT
Lamp
Shelf
Freezer Door Rack
Ice Trays
Ice Cube Box
REFRIGERATOR
COMPARTMENT
Egg Storage Rack
Deodorizer
Water Dispenser
Fresh Meat
Utility Corner
Lamp
Shelves
Bottle Rack
Focused Cooling
Sensor
Vegetable Drawer
Used to keep fruits
and vegetables, etc.
fresh and crisp.
TE
NO
Leveling Screw
Base Cover
• If you found some parts missing from your unit, they may be parts only
used in other models.
4
OPERATIONS
STARTING
When your refrigerator is first installed, allow it 2-3 hours to stabilize at normal operating temperatures
prior to filling it with fresh or frozen foods.
If operation is interrupted, wait 5 minutes before restarting.
DISPLAY PANEL & FUNCTION BUTTONS
●
Super Freeze Button
●
can be used when you
freeze food or ice more
quickly than normal
state.
Whenever you press this
button, the function is on
and off.
If the function is on, the
super freeze leds are on
after shifting 3 times.
●
Freezer
Temperature
Control Button
is used to control
the temperature of
the freezer.
Super Freeze
leds indicates if
●
the super freeze
function operates
or not.
●
Super Cool
Leds indicates
the super cool
function operates
or not.
Temperature leds
●
indicates the temperature status of each
compartment (refrigerator and freezer)
Focused Cooling
Leds turn on if the
door is opened and
change the state for
some minutes after
closed. All leds are
off after certain minutes.
5
●
Super Cool Button
is used to keep in cold
storage more quickly
and effectively.
Whenever you press
this button, the function
is on and off.
If the function is on, the
super cool leds are on
after shifting 3 times.
●
Refrigerator
Temperature
Control Button
is used to control
the temperature of
the refrigerator.
OPERATIONS
DOOR ALARM
When the door of the refrigerator or the freezer is left opened for a while, the alarm sounds three times 1
minute after and then three times every 30 seconds.
SELF TEST
● When
a trouble is occured, this function indicates it. In this case, if you press any operating button, the
refrigerator does not operate and displays abnormal.
● At this time, don't disconnect the power cord from the outlet and inquire to the service center.
● If
you press the 'FRZ. TEMP' button and 'SUPER FREEZE' button at the same time for 2 seconds over,
all lamps on control panel turn on. It checks only the function, not trouble. Unpressing the two buttons, it
turns to the normal condition.
FOCUSED COOLING
● When
you insert new(warmer) food on a shelf, a
focused cooling sensor' senses it and blows out
the cooling air concentrically. So the food is
cooled more quickly.
If you insert some food on the 'shelf 2', the 'sensor 2' senses it and blows out the cooling air
focusingly at 'shelf 2'.
● The 'Focused Cooling System' operates automatically.
● You can cool more effectively as put the food
near to a sensor.
Focused Cooling
Sensor 1
Sensor 2
Sensor 3
Shelf 1
Shelf 2
G
NG
IN
OLLI
OO
C
CO
D
D
E
SE
M
EM
US
CU
STTE
OC
YS
FFO
S
SY
Shelf 3
6
OPERATIONS
SUPER COOL
● This
refrigerator can be operated the cooling fan two speed
(rpm), -'normal' and 'quick'- with 'Super Cool System'. You
can cool the food more quickly because the cooling fan can
operate a quick speed.
● The super cool system operates, when the power is supplied
first. So, you can store food more fresh. The super cool system is released when the temperature of refrigerator compartment get specified degree.
● If needed press the 'SUPER COOL' button on the display
panel.
The function on and off whenever the button is pressed.
The function is released (off) if you don't cease the function
and the food is cooled sufficiently.
SUPER FREEZE
● This
function can be used when you want to freeze or water
more quickly.
● Press the 'SUPER FREEZE' button on the display panel and
the super freeze system is on. This function is on and off
whenever the button is pressed. The function is released (off)
if you don't cease the function and pass some hour
(about 3 hours).
● The noise can be increased instantly because of the quick
speed of the fan.
7
POWER
ON
OPERATIONS
TEMPERATURE CONTROL
You can set each compartment temperature using the
'REF. TEMP' and 'FRZ. TEMP' button .
Whenever pressing the button, the LEDs emit light two
steps.
The temperature of each compartment is lowered as
each LEDs luminesce from "COLD" to "COLDEST".
You can select the desired setting point five steps(from
the COLD to the COLDEST).
For the economic electricity, set each leds to the 'COLD'
position.
ICE MAKING
To make ice cubes, fill the ice tray with water and place
it in the freezer.
● To remove ice cubes, hold the tray at its ends and twist
gently.
●
TIP
●
●
To remove ice cubes easily, run water on the
tray before twisting.
You can disassemble the Ice Tray to secure space in the
freezer.
“Twisting Ice Serve Type: Remove 1 and 2”
1. Ice Tray
1
2. Ice Cube Box
2
8
OPERATIONS
FRESH MEAT
When the door is opened, the warmer air don't influence
in the fresh meat. So you can store food more fresh in it.
● The shelf and inserted fresh meat must be placed at its
position. If it is moved, the fresh meat can't fill the role of
it.
●
DEFROSTING
●
Defrosting takes place automatically.
●
The defrosted water flows down to the evaporating tray which located in the lower back side of the refrigerator and is evaporated automatically.
DEODORIZER(OPTIONAL)
●
By using an "TiO2 catalyst," deodorizing performance is guaranteed.
●
Unpleasant odor of food in fresh food compartment is deodorized with no harm to you and the food.
How to use
As the catalyst is located in cooling air outlet for circulating air in fresh food compartment, there is no
need for any handling.
● Do not prick the cooling air outlet with a sharp tip because the deodorizing catalyst may be damaged.
●
●
When storing food with a strong odor, wrap it or store it in a container with a lid because odor may be
passed on to other foods.
Re-using of the Catalyst
Used some length and the odor is strong, the catalyst can be revived and re-used.
Separate deodorizer in ceiling of refrigerator compartment, dry using hair drier to remove moisture or malodor and oxidize under sunlight to decomposing malodor by ultraviolet.
9
OPERATIONS(water dispenser)
WATER DISPENSER(OPTIONAL)
Features
EXTERIOR
DISPENSER PAD
GRILLE
DRIP TRAY
INTERIOR
HOLE
TAB
HOLDER RING
MOTOR(INSIDE)
WATER TANK
HOLDER
WATER TANK
LOCK DIAL
TAB
CAP
HANDLE
WATER TANK
10
OPERATIONS(water dispenser)
Putting The Water In The Water Tank
1
Turn the lock dial in the direction of the
arrow as shown to remove it and pour water
into the dispenser water tank.
2
3
Place the water tank in the tank holder
inside the refrigerator. Make sure that the
groove on the connecting part is in position
with the tab. Push the connecting part into
the hole until it "Clicks".
4
Close the cap by tilting it and putting one
side in first and then the other side as
shown.
Fix the connecting part in place by means
of the holder ring as shown.
Tab
Groove
ION
UT
CA
• Do not use anything other than water including soft drinks, milk and juices.
• Hot water needs to be cooled before being put in the water tank.
• Always use the holder ring to fix the water tank in place to prevent the tank from moving or
getting loose.
Drinking
1
Press the dispenser pad with the glass.
TE
NO
2
The water is released when the dispenser pad
is pressed. The pad returns to its original position when the glass is removed, and the water
stops its flow.
• The motor rotates in reverse for a few seconds after the dispenser is released to dispose of
any water remaining in the tubes. (This may cause the sound of water being sucked back
inside)
11
OPERATIONS(water dispenser)
CLEANING
Grille and Drip Tray
1
Pull the drip tray out and remove with the grille.
2
Dispose of the water in the kitchen sink, wash
the drip tray and the grille with a mild detergent and rinse thoroughly.
2
Clean the inside and outside of the water tank
with dishwashing detergent and rinse
thoroughly under running water.
Water Tank
1
Remove the cap.
Other Parts
Remove the cap and clean the cap and connecting
part with a mild detergent and rinse thoroughly.
ION
UT
CA
• Use lukewarm water when cleaning.
• Do not use anything other than water. If it is used with soft drinks, put water in the
water tank and discharge three or four cups of water shortly.
12
SUGGESTIONS ON FOOD STORAGE
STORING FOOD
●
Store fresh food in the refrigerator compartment. How food is frozen and thawed is an important factor
in maintaining its freshness and flavor.
●
Do not store food which goes bad easily at low temperatures, such as bananas, pineapples, and melons.
●
Allow hot food to cool prior to storing. Placing hot food in the refrigerator could spoil other food, and lead
to higher electric bills!
●
When storing the food, cover it with vinyl wrap or store in a container with a lid. This prevents moisture
from evaporating, and helps food to keep its taste and nutrients.
●
Do not block air vents with food. Smooth circulation of chilled air keeps refrigerator temperatures even.
●
Do not open the door frequently. Opening the door lets warm air enter the refrigerator, and cause temperatures to rise.
FREEZER COMPARTMENT
●
Do not store bottles in the freezer compartment - they may break when frozen.
●
Do not refreeze food that has been thawed. This causes loss of taste and nutrition.
●
When storing frozen food like ice cream for a long period, place it on the freezer shelf, not in the door
rack.
REFRIGERATOR COMPARTMENT
●
Avoid placing moist food deep inside refrigerator shelves, it could freeze upon direct contact with chilled
air.
●
Always clean food prior to refrigeration. Vegetables and fruits should be washed and wiped, and packed
food should be wiped clean, to prevent adjacent food from spoiling.
●
When storing eggs in their storage rack, ensure that they are fresh, and always store them in a up-right
position, which keeps them fresh longer.
13
CLEANING
Wash all compartments with a baking soda solution.
Rinse and dry.
It is important that your refrigerator be kept clean to
prevent undesirable odors. Spilled food should be
wiped up immediately, since it may acidify and
stain plastic surfaces if allowed to settle.
INTERIOR PARTS - Wash compartment shelves,
door racks, storage trays and magnetic door seals
etc. with the baking soda solution or a mild detergent and warm water. Rinse and dry.
Never use metallic scouring pads, brushes, coarse
abrasive cleaners or strong alkaline solutions on
any surface.
Before you clean, however, remember that damp
objects will stick or adhere to extremely cold surfaces. Do not touch frozen surfaces with wet or
damp hands.
WARNING
EXTERIOR - Use a lukewarm solution of mild soap
or detergent to clean the durable finish of your
refrigerator. Wipe with a clean, damp cloth and
then dry.
Always remove power cord from the wall
outlet prior to cleaning in the vicinity of electrical parts (lamps, switches, controls, etc.).
Wipe up excess moisture with a sponge or
cloth to prevent water or liquid from getting
into any electrical part and causing a electric
shock. Do not use flammable or toxic cleaning liquids.
INTERIOR - Regular cleaning of the interior and
interior parts is recommended. If you have the No
Frost model which defrosts automatically, leave
both doors open during the entire cleaning process.
Disconnect the power supply, and remove food and
all compartment shelves, storage trays etc.
GENERAL INFORMATION
VACATION TIME
IF YOU MOVE
During average length vacations, you will probably
find it best to leave the refrigerator in operation.
Place freezable items in freezer for longer life.
When you plan to be away for an extended period,
remove all food, disconnect the power cord, clean
the interior thoroughly, and leave each door OPEN
to prevent odor formation.
Remove or securely fasten down all loose items
inside the refrigerator.
To avoid damaging the leveling screw(s), turn them
all the way into the base.
ANTI-CONDENSATION PIPE
The outside wall of the refrigerator cabinet may
sometimes get warm, especially just after
Anti-Condensation
Pipe
installation.
Don't be alarmed.
This is due to the anti-condensation pipe, which
pumps hot refrigerant to
prevent "sweating" on the
outer cabinet wall.
POWER FAILURE
Most power failures are corrected in an hour or two
and will not affect your refrigerator temperatures.
However, you should minimize the number of door
openings while the power is off. During power failures of longer duration, place a block of dry ice on
top of your frozen packages.
14
LAMP REPLACEMENT
FREEZER LAMP
1. Unplug the power cord from the outlet.
2. Remove the room lamp lid by taking down while pulling it forward with your
hand after inserting finger into the inside hole as shown in the figure at right.
3. Remove the lamp by turning it counterclockwise and replace new one.
4. Assemble in reverse order of disassembly. Replacement bulb must be the
same specification as original.
REFRIGERATOR LAMP
1. Unplug the power cord from the outlet.
2. Remove the up most refrigerator shelf.
3. Remove the room lamp lid by taking down while pulling it forward with your
hand after inserting finger into the inside hole as shown in the figure at right.
4. Turn the lamp counterclockwise and replace new one.
5. Assemble in reverse order of disassembly. Replacement bulb must be the
same specification as original.
IMPORTANT WARNINGS
DO NOT USE AN EXTENSION CORD
ABOUT GROUNDING (EARTHING)
If possible, connect the refrigerator to its own individual electrical outlet to prevent it and other appliances or household lights from causing an overload that could cause a power outage.
In the event of an electric short circuit, grounding
(earthing) reduces the risk of electric shock by
providing an escape wire for the electric current.
In order to prevent possible electric shock, this appliance must be grounded.
Improper use of the grounding plug can result in an
electric shock. Consult a qualified electrician or service person if the grounding instructions are not completely understood, or if you have doubts on whether
the appliance is properly grounded.
POWER CORD REPLACEMENT
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
DO NOT MODIFY OR EXTEND THE
POWER CORD LENGTH
It will cause electric shock or fire.
VERY DANGEROUS ATTRACTION
An empty refrigerator can be a dangerous attraction
to children. Remove either gaskets, latches, lids or
the entire door from your unused appliance,or take
some other action to make it harmless.
This appliance must be grounded (earthed).
DON'T WAIT! DO IT NOW!
Please don't stain the area near to door switch
with any sweet food so that ants can't interrupt
the normal operation of door switch.
Do not store inflammable materials, explosives
or chemicals in the refrigerator.
Disposal of the old appliance
This appliance contains fluid (refrigerant, lubricant) and is made of parts and materials which are reusable
and/or recyclable.
All the important materials should be sent to the collection center of waste material and can be reused after
rework (recycling). For take back, please contact with the local agency.
15
BEFORE CALLING FOR SERVICE
SERVICE CALLS CAN OFTEN BE AVOIDED!
IF YOU FEEL YOUR REFRIGERATOR IS NOT OPERATING PROPERLY, CHECK THESE POSSIBLE
CAUSES FIRST :
PROBLEM
POSSIBLE CAUSES
REFRIGERATOR DOES
●
NOT OPERATE
●
Has a house fuse blown or circuit breaker tripped?
Has the power cord plug been removed or loosened
from the electrical wall outlet?
REFRIGERATOR OR FREEZER
●
Temperature control not set on proper position.
COMPARTMENT TEMPERATURE
●
Appliance is placed close to wall or heat source.
TOO WARM
●
Warm weather-frequent door openings.
●
Door left open for a long time.
●
Large amount of foods are kept in the refrigerator.
ABNORMAL NOISE(S)
●
Refrigerator is installed in a weak or uneven place,
or leveling screw needs adjusting.
●
Unnecessary objects placed in the back side of the
refrigerator.
REFRIGERATOR
●
HAS ODOR
Foods with strong odors should be tightly covered
or wrapped.
●
Interior needs cleaning.
DEW FORMS ON THE
●
Not unusual during periods of high humidity.
CABINET SURFACE
●
Door may have been left ajar.
16
1
2
2 1
1
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising