Vacuum Cleaner
OWNER'S MANUAL
MODEL
:
V-9000WA
V-9600WA
Please read
carefully and thoroughly the operating
instructions and safety precautions before installing
and operating your vacuum cleaner.
1
2
1
2
2
1
3
4
5
6
7
8
2
1
2
9
11
10
3
1
-2-
Housekeeping
?
Turn the cleaner
off, and disconnect the plug.
?
Press the cord reel button to reel the
?
Place the
?
pipe
cord.(Fig. 25)
holder into the hole at the
rear
side of the
Water may be remained inside the cleaner. In order to
freezing, keep it at 0°C or higher.
-7-
cleaner.(Fig. 26)
prevent the
water remained inside it from
Make the tank empty
When the water in the tank goes to the
from sucking.(Fig. 16)
specific level,
the
device works to
safety
prevent the
water
Then, make the tank empty.
With the power
Open
turn the hose connected with the tank to the left to be
off,
the cover, and disconnect the tank from the main
Make the tank
removed.(Fig. 17)
body.
empty (Fig. 18), and reassemble it.
Shampoo cleaning
?
?
Do the
Open
dry
dust
cleaning.
the cover, and
remove
the filter from the tank.
?
Remove the floor nozzle from the
?
Insert the tube into the holder of the
?
Insert the connector
?
?
on
the
the
and insert the
pipe,
of the tube into the
cap, and fill the
Open
shampoo
shampoo.(Fig. 19)
Read the appropriate
ratio value
Connect the
?
Pull the handle of the hose
?
and insert the spray nozzle.
When you disconnect the connector, press the
?
?
top
pipe,
plug,
and press the
shampoo
on
the
clip
trigger
remove
into the
pipe.
of the hose handle.
button of the
tank with the
trigger.
appropriate
ratio of water and
shampoo.
shampoo button.(Fig. 20)
handle, then the shampoo is sprayed
at the spray
nozzle.(Fig. 21, 22)
Spray the shampoo evenly over the area to be cleaned, and press the power button to suck the
sprayed shampoo. At this time, you should pull to clean toward your body. If you push to clean, you
can not suck the shampoo.(Fig. 6)
When you hear the big noise from the main body during the
because it indicates that the shampoo tank is empty.
Caution
during
Use
the
only
In order to
the
shampoo
the
remove
make the tank
empty,
and
When the
tank is
Cleaning
Separate
Then,
operate
exhaust
cover
Do not clean in
a
a
inside the main
body
after the
empty, do
not
operate for longer than
one
safety filter.(Fig. 23, 24)
and dust off.
soapy water.
dish-washer
washing machine.
sufficiently in shade
or
Remove the moisture and filter
shampoo cleaning,
shampoo cleaning.
about for 30 seconds at the state of the
the exhaust filter and
wash filter in
shampoo tank,
solution dedicated for LG.
shampoo remaining
only.
shampoo
pressed.
refill the
shampoo cleaning
Use the clean water
button
shampoo cleaning,
-6-
for about
a
day.
minute with the
shampoo
12
14
13
Clip
Separation-button
Connector
15
16
Safety
17
device
18
19
21
22
2
1
20
OFF
ON
23
-3-
24
25
26
Red mark
Yellow mark
Handle
Hose
Cord reel button
Cover assy
Hose handle
Shampoo tank cap
Shampoo
tank
Clamp
Shampoo
button
Power switch
button
Inlet dust
Power cord
Outlet cap
Pipe
Spray nozzle
Valve
Dusting
Crevice
Upholstery
brush
tool
nozzle
Floor nozzle
-4-
Cloth filter
Tank
Shampoo bottle
OPERATING INSTRUCTION
Preparation
?
Before
Using
Connect the hose with the tank: Insert the end of the hose into the
of the
opening
tank, and
turn it
right.(Fig. 1)
?
?
?
?
Connect the outlet cap with the valve: Connect the outlet cap with the
Connect the
with the hose handle: There
pipe
pipe holder.(Fig. 2)
Connect the other pipe.(Fig. 3)
Connect the nozzle with the pipe:
two
are
pipes.
valve, and
Connect the
Connect the nozzle which you want to
pipe
use
turn it
right.(Fig. 1)
which dose not have the
with the
pipe. (Fig. 4)
NOZZLE
?
Floor nozzle: Use it to clean the
dry dust.
carpet(without brush) and a tile(with brush).(Fig. 5)
Spray nozzle: Use it to suck water or to do a shampoo cleaning.
You can use it to clean a carpet(without brush) and a tile(with brush).(Fig. 6)
You
?
it to clean
can use
a
ACCESSORY
You
?
?
?
can use
all of accessories with
Upholstery
nozzle: Use it to clean
Crevice tool: Use it to clean
Dusting
How to
Cleaning
?
a
brush: Use it to clean
pipe or directly with a hose handle.
upholstery such as furniture, curtain, etc..
a
crevice such
some
as
window
frame, door crevice,
where difficult to reach such
If not
lampshade, shelf,
etc.
use
a
dry
dust
the cover, and check whether the inside of the tank is empty
empty, make the tank completely empty and make it dry.
Open
etc.
inside of
as
?
Insert the cloth
?
Insert the floor
?
Connect the
Making
dry.(Fig. 7)
filter(Fig. 8), and closer the cover.(Fig. 9)
nozzle.(Fig. 4)
plug, and press power button.(Fig. 10)
the cloth filter empty
When the filter becomes to be
cleaning
or
any
full, the suction power becomes
to
weak, and you
can
not do the
more.
Then, clean the cloth filter.
With the power
Slide out the
Sucking
?
Open
If
?
off, open the
clip
of the
cover
and
filter(Fig. 12),
remove
clean the
the
filter.(Fig. 11)
filter, and reinstall the clip again.
water
the cover, and check whether the cloth filter is installed at the tank
remove the filter.
or
not.
installed,
Insert the spray
nozzle.(Fig. 13)
?
Insert the tube into the holder of the
?
Insert the connector
?
When
?
Connect the
?
You
on
the
pipe,
and insert the
top of the tube into the
clip
trigger of
into the
pipe.(Fig. 13)
handle.(Fig. 14)
trigger.(Fig. 14)
the hose
disconnecting the connector, press the remove button of the
plug, and press the power button.
can suck water only with the hose handle after removing the pipe
-5-
from the hose
handle.(Fig. 15)
P/No.: 3828Fi3741J
Made in KOREA
">
