LG | 20LC1RB | LG 20LC1RB Owner’s Manual

LCD TV
OWNER’S MANUAL
MODELS: 15LC1R
*
20LC1R *
23LC1R *
Please read Information Manual included together
before reading this manual and operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer when you require service.
P/NO : 38289U0018E (0607-REV03)
Printed in Korea
Contents
Installation
3
Location and function of controls
Remote control handset
Battery installation / Front/ Rear
6
Basic operation
On and off
On screen language/ country selection
10
On screen menus
Menu selection / Programme selection
Volume adjustment
11
Setting up TV stations
Auto programme tuning
Manual programme tuning
Assigning a station name
Programme edit
Favourite programme
Calling the programme table
12
Picture adjustment
PSM (Picture Status Memory)
CSM (Colour Status Memory)
Picture adjustment
17
Sound adjustment
SSM (Sound Status Memory)
Sound adjustment / Stereo/ Dual reception
NICAM reception / Sound output selection
18
Time Menu
Clock / On/Off time
Auto sleep / Sleep timer
20
Other functions
TV, AV and PC modes
Auto AV switching / Child lock / Power indicator
22
Teletext
Switch on/off
SIMPLE text / TOP text
FASTEXT / Special teletext functions
24
Connection of external equipment
26
Aerial socket
Euro scart socket (VCR) / S-Video/Audio in sockets (S-Video)
Euro scart socket (DVD)
DVD input sockets (23LC1R*) / DTV in sockets (15/23LC1R*)
Audio/Video in sockets / Headphone socket
2
Connection of PC
PC in socket (15/23LC1R*)
PC Setup
Picture format (23LC1R* only)
28
Troubleshooting check list
31
Product Specifications
32
Installation
Unfolding the stand base
1. Place the set with its front facing downward on a cushion or soft cloth.
2. Hold down the release button inside the stand and strongly pull out the stand with your two hands.
Note: Here shown may be somewhat different from your set.
The stand won't move if you
don't press release button.
Connection of TV
1. Connect the aerial cable to the socket marked +75 Ω on the back. For the best reception an
outdoor aerial should be used.
2. To connect an additional equipment, see the Connection of external equipment section.
3. Connect the power cord.
Note: Here shown may be somewhat different from your set.
(
)
3
Installation
Wall Mount: Horizontal installation
< 20LC1R* only >
2-Ring spacers
4 inches
4 inches
Place the ring spacers on the set before installing the
wall mounting bracket so that the inclination of the
backside of the set can be adjusted perpendicularly.
4 inches
4 inches
4 inches
For proper ventilation, allow a clearance of 4" on each side and from the wall. Detailed installation
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
Desktop Pedestal Installation
4 inches
4 inches
4 inches
4 inches
For proper ventilation, allow a clearance of 4" on each side and from
the wall.
4
Installation
Positioning your display
Adjust the position of the panel in various ways for maximum comfort.
• Tilt range
12
Be careful that your hands are not
pressed down when tilting the screen.
Location
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken
not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is
placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the
back of the TV.
When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.
5
Location and function of controls
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the top
panel of the set. Only the remote control handset supplied will
operate this set.
Remote control handset
MUTE
POWER
1
TV
INPUT
I/II
2
10 Before you use the remote control handset, please install the
batteries. See the next page.
11
1. MUTE
switches the sound on or off.
12
Press the MUTE button. The sound is switched off and the display
appears.
You can cancel it by pressing the MUTE, F / G, I/II, or SSM button.
LIST Q.VIEW MENU
13
3
4
2. TV
returns to the TV mode.
clears the menu from the screen.
switches the set on from standby.
PR
5
OK
VOL
VOL
PR
6
7
8
3. LIST
displays the programme table.
1
2
3
4
5
6
7
8
9
SSM
0
PSM
SLEEP
ARC
4. Q.VIEW
returns to the previously viewed programme.
Press the Q.VIEW button to view the last programme you were
watching.
Note : This function works only when Favourite programme is set
to Off. Otherwise each press of this button will select a stored
14 favorite programme.
TEXT
9
15
UPDATE
TIME
SIZE
MIX
HOLD
REVEAL
?
INDEX
i
MODE
M
5.
D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Down/Up)
adjusts the volume.
adjusts menu settings.
OK
accepts your selection or displays the current mode.
6. NUMBER BUTTONS
switches the set on from standby and selects a programme.
7. SSM (Sound Status Memory)
recalls your preferred sound setting.
8. ARC
select your desired picture format.
[With ARC]
9. SLEEP
sets the sleep timer.
10. INPUT
selects the remote operating mode.
switches the set on from standby.
6
Location and function of controls
11. POWER
switches the set on from standby or off to standby.
12. I/II
selects the language during dual language broadcast.
13. MENU
selects a menu.
MUTE
14. PSM (Picture Status Memory)
recalls your preferred picture setting.
1
15. TELETEXT BUTTONS
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
2
* : No function
COLOURED BUTTONS : These buttons are used for teletext (only
TELETEXT models) or programme edit.
POWER
10
11
TV
INPUT
I/II
12
LIST Q.VIEW MENU
13
3
4
PR
5
OK
VOL
VOL
PR
Battery installation
The remote control handset is powered by two AAA batteries. To load
the batteries, turn the remote control handset over and open the battery compartment. Install two batteries as indicated by the polarity
symbols ( + and - ) marked inside
the compartment.
6
7
8
1
2
3
4
5
6
7
8
9
SSM
0
PSM
SLEEP
*
TEXT
9
Note : To avoid damage from possible battery leakage, remove the
batteries if you do not plan to use the remote control handset for an
extended period of time.
14
15
UPDATE
TIME
SIZE
MIX
HOLD
REVEAL
?
INDEX
i
MODE
M
[Without ARC]
7
Location and function of controls
Front
Top panel
PR
VOL
OK
MENU
INPUT
/I
6
5
4
3
2
1
7
8
E / D (Programme Down/Up)
selects a programme or a menu item.
switches the set on from standby.
1. ON/OFF (r / I)
switches the set on from standby or off to
standby.
6.
2. INPUT
selects the remote operating mode.
switches the set on from standby.
7. REMOTE CONTROL SENSOR
3. MENU
selects a menu.
4. OK
accepts your selection or displays the current
mode.
5.
8
F / G (Volume Down/Up)
adjusts the volume.
adjusts menu settings.
8. POWER/STANDBY INDICATOR
illuminates orange in standby mode.
illuminates blue when the set is switched on.
Location and function of controls
Rear
23LC1R* only
15/ 23LC1R*
L
COMPONENT
(VIDEO / AUDIO Input)
R
AUDIO
VIDEO
COMPONENT
PC INPUT
JACK
PC INPUT
ANTENNA
INPUT
PC SOUND
INPUT
ANT IN ( 75 ) PC SOUND
AV 1
AC INPUT
H/P
AV 2
AC INPUT
EURO SCART
SOCKET
AUDIO/VIDEO
INPUT
S-VIDEO
S-VIDEO
INPUT
HEADPHONE
JACK
FOR SERVICE ANTENNA
INPUT
JACK
20LC1R*
FOR SERVICE
ANT IN ( 75 )
AV 1
AC INPUT
H/P
AV 2
AC INPUT
EURO SCART
SOCKET
AUDIO/VIDEO
INPUT
S-VIDEO
S-VIDEO
INPUT
HEADPHONE
JACK
9
Basic operation
On and off
1. Press the POWER, D / E, TV, INPUT or NUMBER buttons to
switch it on fully.
2. Press the POWER button. The set reverts to standby mode.
3. Pull out mains plugs to switch the set off.
MUTE
TV
POWER
INPUT
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains plug is
replaced in the mains power socket.
I/II
On-Screen Menu Language / Country Selection
Q.VIEW MENU
Installation guide menu appears on TV screen when it is turned on for the
first time.
1. Press the D / E / F / G button and then, OK button to select your
PR
OK
VOL
VOL
desired language.
2. Press the D / E / F / G button and then, OK button to select your
country.
PR
* If you want to change Language/ Country selection
1
2
3
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Language.
4
5
6
The menus can be shown on the screen in the selected language.
Or, Press the G button and then D / E button to select Country.
7
8
9
SSM
0
3. Press the G button and then D / E / F / G button to select your
desired language or country.
4. Press the OK button.
5. Press the TV button to return to normal TV viewing.
Note:
a. If you don’t finish set up Installation Guide by pressing MENU
button or time out of OSD (On Screen Display) display, it will
continuously appear until completing set up whenever the set
is turned on.
b. If you select wrong local country, the teletext may not appear
correctly on the screen and some problem may happen during
teletext operation.
c. Hebrew is added to Country of Installation Guide according
to the countries which using Hebrew languages.
10
On screen menus
Menu selection
1. Press the MENU button and then D / E button to display each menu.
2. Press the G button and then D / E button to select a menu item.
3. Change the setting of an item in the sub or pull-down menu with
F / G button.
You can move to the higher level menu by pressing the OK
button and to move to the lower level menu by pressing the
MENU button.
Note :
a. In the TV/AV mode, the SCREEN (20LC1R*) menu is not displayed.
b. In the teletext mode, menus are not displayed.
c. On some models, the Language will not be displayed.
MENU
PR
OK
VOL
VOL
PR
Programme selection
You can select a programme number with the
buttons.
D
/
E
or NUMBER
Volume adjustment
Press the
F
/
G
button to adjust the volume.
PICTURE
STATION
Auto programme
Manual programme
Programme edit
Favourite programme
D
E
MENU
FG
SOUND
PSM
CSM
Contrast
Brightness
Colour
Sharpness
D
E
OK
MENU
FG
SSM
AVL
Balance
D
E
OK
PICTURE menu
STATION menu
SPECIAL
MENU
FG
OK
SOUND menu
TIME
Clock
Off time
On time
Auto sleep
Language
Country
Input
Child lock
Power indicator
D
E
MENU
FG
OK
SPECIAL menu
D
E
MENU
FG
OK
TIME menu
11
Setting up TV stations
STATION
Up to 100 TV stations can be stored by programme numbers (0 to 99).
Once you have preset the stations, you will be able to use the D / E
or NUMBER buttons to scan the stations you have programmed.
Stations can be tuned using automatic or manual modes.
Auto programme
Manual programme
Programme edit
Favourite programme
Auto programme tuning
D
E
MENU
FG
All stations that can be received are stored by this method. It is
recommended that you use auto programme during installation
of this set.
OK
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select Auto
programme.
Auto programme
TV
BG
I
DK
L
System
Storage from
Search
MENU
D
E
PR
OK
VOL
VOL
PR
1
2
3
4
5
6
7
8
9
0
MENU
FG
OK
3. Press the G button. Select a TV system with the G button and
then D / E button on the System menu;
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
L
: SECAM L/L’ (France)
4. Press the OK button.
5. Press the D / E button to select Storage from.
6. Select the beginning programme number with the F / G button
or NUMBER buttons on the Storage from pull-down menu. Any
number under 10 is entered with a numeric ‘0’ in front of it, i.e.
‘05’ for 5.
7. Press the D / E button to select Search.
Auto programme
System
Storage from
Search
Auto programme
To start
C21
2
BG
5%
MENU : Stop
MENU
8. Press the G button to begin auto programming.
All receivable stations are stored. The station name is stored for
stations which broadcast VPS (Video Programme Service),
PDC (Programme Delivery Control) or TELETEXT data. If no
station name can be assigned to a station, the channel number
is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47),
followed by a number.
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the ‘Programme edit’ section
to edit the stored programme.
9. Press the TV button to return to normal TV viewing.
12
Setting up TV stations
STATION
Manual programme tuning
Auto programme
Manual programme
Programme edit
Favourite programme
Manual programme lets you manually tune and arrange the
stations in whatever order you desire. Also you can assign a station
name with five characters to each programme number.
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select Manual
programme.
3. Press the G button and then D / E button to select Storage.
D
E
MENU
FG
OK
Manual programme
29
Storage
System
Channel
Fine
Search
Name
TV
MENU
D
E
MENU
FG
OK
4. Select the desired programme number (0 to 99) with the F / G
button or NUMBER buttons on the Storage menu. Any number
under 10 is entered with a numeric ‘0’ in front of it, i.e. ‘05’ for 5.
5. Press the D / E button to select System.
6. Select a TV system with the G button and then F / G button on
the System menu;
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
L
: SECAM L/L’ (France)
PR
OK
VOL
VOL
PR
1
2
3
4
5
6
7
8
9
7. Press the OK button.
8. Press the D / E button to select Channel.
9. Press the G button and then D / E button to select VHF/UHF or
Cable on the Channel menu.
If possible, select the channel number directly with the number
buttons. Any number under 10 is entered with a numeric ‘0’ in
front of it, i.e. ‘05’ for 5.
0
10. Press the OK button.
11. Press the D / E button to select Fine.
12. Use the F / G buttons to adjust frequency on your TV.
13. Press the OK button to store it.
14. Press the D / E button to select Search.
15. Press the G button and then F / G button to commence searching on the Search pull-down menu. If a station is found the search
will stop.
Manual programme
Storage
System
Channel
Fine
Search
Name
D
E
MENU
FG
FG
OK
16. Press the OK button to store it.
17. To store another station, repeat steps 3 to 13.
18. Press the TV button to return to normal TV viewing.
13
Setting up TV stations
Assigning a station name
1. Repeat the ‘Manual programme tuning’ steps 1 to 2.
2. Press the G button and then D / E button to select Name.
3. Press the G button and then use the D / E. You can use a blank,
+, -, the number 0 to 9 and the alphabet A to Z.
STATION
Auto programme
Manual programme
Programme edit
Favourite programme
D
E
MENU
FG
A~Z
OK
a~z
[]
0~9
?
!
#
-
+
[ ] : blank
With the F button you can select in the opposite direction.
4. Select the position by pressing the F / G button and then make
your choice of the second character, and so on.
5. Press the OK button to store it.
6. Press the TV button to return to normal TV viewing.
TV
MENU
PR
OK
VOL
VOL
PR
SSM
14
PSM
Setting up TV stations
Programme edit
STATION
Auto programme
Manual programme
Programme edit
Favourite programme
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
insert a blank station data into the selected programme number.
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select Programme
edit.
3. Press the G button to display the Programme edit menu.
D
E
MENU
FG
OK
Programme edit
0
C 03
1 BLN 03
2
C 12
3
S 66
4
S 67
5
6
7
8
9
Delete
Move
D
E
MENU
FG
S 69
S 17
-------------
TV
Copy
Skip
MENU
OK
Deleting a programme
1. Select a programme to be deleted with the D / E or F / G button.
2. Press the RED button twice.
The selected programme is deleted, all the following
programmes are shifted up one position.
Programme edit
0
C 03
1 BLN 03
2
C 12
3
S 66
4
S 67
5
6
7
8
9
PR
OK
VOL
VOL
S 69
S 17
-------------
PR
1
2
3
4
5
6
7
8
9
Delete
D
E
MENU
FG
OK
Copying a programme
1. Select a programme to be copied with the D / E or F / G button.
2. Press the GREEN button.
All the following programmes are shifted down one position.
0
Moving a programme
1. Select a programme to be moved with the D / E or F / G button.
2. Press the YELLOW button.
3. Move the programme to the desired programme number with
the D / E or F / G button.
4. Press the YELLOW button again to release this function.
Skipping a programme number
1. Select a programme number to be skipped with the D / E or F / G
button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be
unable to select it using the D / E button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
Press the TV button to return to normal TV viewing.
15
Setting up TV stations
STATION
Favourite programme
Auto programme
Manual programme
Programme edit
Favourite programme
This function lets you select your favourite programmes directly.
1. Press the MENU button and then D / E button to select the
STATION menu.
D
E
2. Press the G button and then
programme.
MENU
FG
OK
D
/
E
to select Favourite
Favourite programme
On
--------D
E
TV
LIST Q.VIEW MENU
3.
4.
5.
6.
---------------------------------
MENU
FG
OK
Press the G button and then F / G button to select On or Off.
Press the D / E button to select - - - - - - - .
Select a desired programme with the F / G button.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
7. Press the TV button to return to normal TV viewing.
Repeatedly press the YELLOW button to select stored favourite
programmes.
PR
OK
VOL
VOL
PR
Calling the programme table
You can check the programmes stored in the memory by displaying
the programme table.
Displaying programme table
Press the LIST button to display the Programme table menu.
The programme table appears on the screen. One programme
table contains ten programmes as below.
0 C 03
1 BLN 03
2 C 12
3 S 66
4 S 67
D
E
MENU
FG
5
6
7
8
9
S
S
S
C
C
69
17
22
09
11
OK
Note :
a. You may find some blue programmes. They have been set up to
be skipped by auto programming or in the programme edit mode.
b. Some programmes with the channel number shown in the
programme table indicate there is no station name assigned.
Selecting a programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
The set switches to the chosen programme number.
Paging through a programme table
There are 10 programme table pages in which contain 100
programmes.
Pressing the D / E or F / G button repeatedly turns the pages.
Press the TV button to return to normal TV viewing.
16
Picture adjustment
PICTURE
PSM (Picture Status Memory)
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select PSM.
3. Press the G button and then D / E button to select a picture setting on the PSM menu.
4. Press the OK button.
PSM
CSM
Contrast
Brightness
Colour
Sharpness
D
E
MENU
FG
OK
PICTURE
Dynamic
Standard
Mild
Game
User
PSM
CSM
Contrast
Brightness
Colour
Sharpness
D
E
MENU
FG
OK
TV
5. Press the TV button to return to normal TV viewing.
MENU
You can also recall a desired picture (Dynamic, Standard, Mild,
Game or User) with PSM button on the remote control. The picture
Dynamic, Standard, Mild and Game are programmed for optimum
picture reproduction at the factory and cannot be changed.
PR
CSM (Colour Status Memory)
OK
VOL
VOL
Selecting a factory setting colour set.
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select CSM.
3. Press the G button and then D / E button to select a color setting on the CSM menu: Cool, Normal, Warm or User (Red,
Green, Blue).
4. Press the OK button.
5. Press the TV button to return to normal TV viewing.
Picture adjustment
PR
PSM
You can adjust picture contrast, brightness, colour intensity,
sharpness to the levels you prefer.
1. Press the MENU button and then
PICTURE menu.
D
/
button to select the
E
PICTURE
PSM
CSM
Contrast
Brightness
Colour
Sharpness
D
E
MENU
FG
Contrast
47
D
Contrast
85
F
G
E
OK
2. Press the D / E button to select the desired picture item.
3. Press the F / G button to make appropriate adjustments.
4. Press the TV button to return to normal TV viewing.
17
Sound adjustment
SSM (Sound Status Memory)
SOUND
SSM
AVL
Balance
You can select your preferred sound setting; Flat, Music, Movie or
Sports and you can also adjust the sound frequency of the equalizer.
1. Press the MENU button and then D / E button to select the
SOUND menu.
SOUND
D
E
MENU
FG
Flat
Music
Movie
Sports
User
SSM
AVL
Balance
OK
D
E
TV
MENU
MENU
FG
G
OK
2. Press the G button and then D / E button to select SSM.
3. Press the G button and then D / E button to select a sound
setting on the SSM menu.
Sound Frequency Adjustment
a. Press the OK button in User.
b. Select a sound band by pressing the F / G button.
c. Make appropriate sound level with the D / E button.
d. Press the OK button to store it for the sound User.
PR
OK
VOL
VOL
PR
0.1
D
E
SSM
MENU
0.3
FG
1
3
8
Khz
OK
Press the TV button to return to normal TV viewing.
You can also recall a desired sound setting (Flat, Music, Movie, Sports
or User) with SSM button on the remote control. The sound settings
Flat, Music, Movie and Sports are programmed for optimum sound
reproduction at the factory and cannot be changed.
Note : If you press the SSM button after making appropriate
adjustment on the User sub menu, the display User automatically
appears even though you have already set a factory preset setting;
Flat, Music, Movie or Sports.
SOUND
SSM
AVL
Balance
D
E
MENU
FG
On
Off
OK
Sound adjustment
You can adjust balance, AVL (Auto Volume Leveler).
AVL automatically keeps on an equal volume level even if you
change programmes.
1. Press the MENU button and then D / E button to select the
SOUND menu.
2. Press the G button and then D / E button to select the desired
sound item; AVL or Balance.
3. Make desired adjustment with the F / G, D / E and then press
the OK button.
4. Press the TV button to return to normal TV viewing.
18
Sound adjustment
Stereo/Dual reception
When a programme is selected, the sound information for the
station appears after the programme number and station name
disappear.
Broadcast
Mono
Stereo
Dual
On Screen Display
MONO
STEREO
DUAL I
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II
button twice again.
I/II
Language selection for dual language broadcast
If a programme is received in two languages (dual language), you
can switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II
button repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the
loudspeakers.
DUAL I+II sends a separate language to each loudspeaker.
NICAM reception
If your set is equipped with the receiver for NICAM reception, the
high quality NICAM (Near Instantaneous Companding Audio
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
1. When NICAM mono is received, you can select NICAM MONO
or FM MONO.
2. When NICAM stereo is received, you can select NICAM
STEREO or FM MONO. If the stereo signal is weak, switch to
FM mono.
3. When NICAM dual is received, you can select NICAM DUAL I,
NICAM DUAL II or NICAM DUAL I+II or MONO. When FM
mono is selected the display MONO appears on the screen.
Sound output selection
In AV mode, you can select output sound for the left and right loudspeakers.
Repeatedly press the I/II button to select the sound output.
L+R : Audio signal from audio L input is sent to left loud-speaker
and audio signal from audio R input is sent to right loudspeaker.
L+L : Audio signal from audio L input is sent to left and right loudspeakers.
R+R : Audio signal from audio R input is sent to left and right loudspeakers.
19
TIME Menu
Clock
TIME
Clock
Off time
On time
Auto sleep
D
E
You must set the time correctly before using on/off time function.
1. Press the MENU button and then D / E button to select the
TIME menu.
2. Press the G button and then D / E button to select Clock.
Time
MENU
FG
OK
Clock
Off time
On time
Auto sleep
D
E
MENU
FG
-i-i:i-i-
OK
3. Press the G button and then D / E button to adjust the hour.
4. Press the G button and then D / E button to adjust the minute.
5. Press the MENU button to save.
MENU
On/Off time
The off timer automatically switches the set to standby at the
preset time.
PR
OK
VOL
VOL
PR
1. Press the MENU button and then D / E button to select the
TIME menu.
2. Press the G button and then D / E button to select Off time or
On time.
3. Press the G button and then D / E button to select On.
To cancel On/Off time function, press the D / E button to
select Off.
Time
Clock
Off time
On time
Auto sleep
D
E
MENU
FG
-i-i:i-iPr.
0
Vol. 30
On
OK
4. Press the G button and then D / E button to adjust the hour.
5. Press the G button and then D / E button to adjust the minute.
6. Only On time function; Press the G button and then D / E
button to adjust volume level and programe number.
7. Press the MENU button to save.
Note :
a. In the event of power interruption (disconnection or power
failure), the clock must be reset.
b. Two hours after the set is switched on by the on time function it
will automatically switch back to standby mode unless a button
has been pressed.
c. Once the on or off time is set, these functions operate daily at
the preset time.
d. Off Timer function overrides On Timer function if they are set to
the same time.
e. The set must be in standby mode for the On Timer to work.
20
TIME Menu
TIME
Auto sleep
Clock
Off time
On time
Auto sleep
If you select On on the Auto sleep menu, the set will automatically switch itself to standby mode approximately ten minutes after a
TV station stops broadcasting.
1. Press the MENU button and then D / E button to select the
TIME menu.
2. Press the G button and then D / E button to select Auto sleep.
3. Press the G button and then D / E button to select On or Off.
D
E
MENU
FG
OK
Time
Clock
Off time
On time
Auto sleep
D
E
MENU
FG
On
Off
OK
MENU
4. Press the MENU button to save.
Sleep timer
You don’t have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the preset time has elapsed.
Press the SLEEP button to select the number of minutes.
The display ‘
--- Min’ will appear on the screen, followed by 10,
20, 30, 60, 90, 120, 180 and 240. The timer begins to count down
from the number of minutes selected.
Note :
a. To view the remaining sleep time, press the SLEEP button
once.
b. To cancel the sleep time, repeatedly press the SLEEP button
until the display ‘
--- Min’ appears.
c. When you switch the set off, the set releases the preset sleep
time.
PR
OK
VOL
VOL
PR
SLEEP
21
Other functions
SPECIAL
TV, AV and PC modes
Language
Country
Input
Child lock
Power indicator
D
E
MENU
FG
Inputs can be set for TV, AV or PC mode. AV mode is used when a
video cassette recorder (VCR), or other equipment is connected to
the set.
Note : When a VCR is connected via the aerial socket the set is
used in TV mode. See the ‘Connection of external equipment’ section.
OK
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Input.
3. Press the G button and then D / E button to select TV, AV1,
AV2, RGB-DTV, RGB-PC or Component.
SPECIAL
TV
Language
Country
Input
Child lock
Power indicator
MENU
D
E
PR
OK
VOL
VOL
PR
MENU
FG
TV
AV1
AV2
RGB-DTV
RGB-PC
Component
OK
The AV and PC modes are :
AV 1 : VCR connected to the Euro scart socket of the set.
AV 2 : VCR connected to the AV2 or S-Video of the set.
RGB-DTV : SET TOP connected to the PC INPUT and PC
SOUND socket of the set. (15/23LC1R*)
RGB-PC : PERSONAL COMPUTER connected to the PC
socket of the set. (15/23LC1R*)
Component : DVD connected to the COMPONENT sockets on
the back of set. (23LC1R only)
*
4. Press the TV button to return to normal TV viewing.
Auto AV switching
SSM
PSM
If your VCR outputs an AV switching voltage when connected to the
Euro scart socket, the set will switch to AV1 mode automatically. But
if you want to keep on watching TV mode, press the D / E or NUMBER buttons.
22
Other functions
SPECIAL
Child lock
Language
Country
Input
Child lock
Power indicator
The TV can be set so that the remote control handset is needed to
control it. This feature can be used to prevent unauthorized viewing.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Child lock.
3. Press the G button and then D / E button to select On or Off
on the Child lock menu.
D
E
MENU
FG
OK
SPECIAL
Language
Country
Input
Child lock
Power indicator
D
E
MENU
FG
On
Off
TV
MENU
OK
4. Press the TV button to return to normal TV viewing.
With the lock on, the display Child lock on appears on the screen
if any button on the top panel is pressed while viewing the TV.
PR
OK
VOL
VOL
Power indicator
PR
Use this function to set the power indicator on the front side of the
product to On or Off. If you set On at any time, the power indicator
will automatically be turned on. Although you select Off, set front
light turns on for a moment when the set turns on.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Power indicator.
3. Press the G button and then D / E button to select On or Off
on the Power indicator menu.
SSM
PSM
SPECIAL
Language
Country
Input
Child lock
Power indicator
D
E
MENU
FG
On
Off
OK
4. Press the TV button to return to normal TV viewing.
23
Teletext
- This feature is not available in all countries.
Teletext (or TOP text) is an optional function, therefore only a set with the teletext system can receive the teletext broadcast.
Teletext is a free service broadcast by most TV stations which gives up-to-theminute information on news, weather, television programmes, share prices
and many other topics.
The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT
systems. SIMPLE (standard teletext) consists of a number of pages which are
selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext
information.
Switch on/off
PR
OK
VOL
VOL
PR
1
2
3
4
5
6
7
8
9
Press the TEXT button to switch to teletext. The initial page or last page
appears on the screen.
Two page numbers, TV station name, date and time are displayed on the
screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the TEXT button to switch off
teletext. The previous mode reappears.
SIMPLE text
Page selection
1. Enter the desired page number as a three digit number with the NUMBER
buttons. If during selection you press a wrong number, you must complete
the three digit number and then re-enter the correct page number.
2. The D / E button can be used to select the preceding or following page.
0
TEXT
24
UPDATE
TIME
SIZE
MIX
HOLD
REVEAL
?
INDEX
i
MODE
M
Programming a colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
ton to switch to LIST mode.
M but-
Four teletext page numbers of your choice can be colour coded and easily
selected by pressing the corresponding coloured button on the remote control
handset.
1. Press a coloured button.
2. Using the NUMBER buttons, select the page you wish to programme.
3. Press the OK button. Then the selected page is stored as the selected
page number by blinking once. From now on, you can select this page
with the same coloured button.
4. The three other coloured buttons are programmed in this way.
Teletext
TOP text
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field
denotes the next group and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next block.
3. With the green button you can proceed to the next existing page with automatic overflow to the next
group. Alternatively the D button can be used.
4. The red button permits to return to previous selection. Alternatively the E button can be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by pressing the
corresponding coloured button.
Page selection
1. Press the i button to select the index page.
2. You can select the pages which are colour coded along the bottom line with the same coloured buttons.
3. Corresponding to the SIMPLE teletext mode, you can select a page by entering its three digit page
number with the NUMBER buttons in FASTEXT mode.
4. The D / E button can be used to select the preceding or following page.
Special teletext functions
?
REVEAL
Press this button to display concealed information, such as solutions of riddles or puzzles.
Press this button again to remove the information from the display.
SIZE
Selects double height text.
Press this button to enlarge the top half of the page.
Press this button again to enlarge the bottom half of the page.
Press this button again to return to the normal display.
UPDATE
Displays the TV picture on the screen while waiting for the new teletext page.
The display
will appear at the top left hand corner of the screen. When the updated page
is available then display
will change to the page number.
Press this button to view the updated teletext page.
HOLD
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub
pages.
The number of sub pages and the sub page displayed is, usually, shown on the screen below
the time. When this button is pressed the stop symbol is displayed at the top left-hand corner
of the screen and the automatic page change is inhibited.
To continue press this button again.
MIX
Displays the teletext pages superimposed on the TV picture.
To switch the TV picture off press this button again.
TIME
When viewing a TV programme, press this button to display the time at the top right hand corner of the screen. Press this button again to remove the display. In the teletext mode, press this
button to select a sub page number. The sub page number is displayed at the top left hand corner of the screen. To hold or change the sub page, press the NUMBER buttons.
Press again to exit this function.
25
Connection of external equipment
You can connect additional equipment, such as VCRs, camcorders
etc. to your set. Examples are shown below.
(- This part of Connection of external equipment mainly use pictures for the 23LC1R*.)
Aerial socket
PC INPUT
ANT IN ( 75 ) PC SOUND
1. Connect the RF out socket of the VCR to the aerial socket of
the set.
2. Connect the aerial cable to the RF aerial in socket of the VCR.
3. Store the VCR channel on a desired programme number using
the ‘Manual programme tuning’ section.
4. Select the programme number where the VCR channel is
stored.
5. Press the PLAY button on the VCR.
AV 1
H/P
S-VIDEO
AV 2
VCR
Euro scart socket (VCR)
PC INPUT
ANT IN (
AV 1
1. Connect the Euro scart socket of the VCR to the Euro scart
socket of the set.
2. Press the PLAY button on the VCR.
If your VCR outputs an AV switching signal via the Scart lead the
set will auto switch to AV 1 mode on start of playback, but if you
want to keep on watching in TV mode, press the D / E or NUMBER buttons.
S-VIDE
AV 2
Otherwise press the INPUT button on the remote control
handset to select AV1. The VCR play back picture appears on
the screen.
You can also record programmes received by the TV on video
tape.
VCR
Note :
a. Signal type RGB, i.e. the signals red, green and blue can only
be selected for the Euro scart and the AV 1 can be received.
These signals are transmitted, for example, by a pay TV
decoder, game machine or photo CD unit, etc.
b. If the S-VHS signal is received through the S-VIDEO, you must
change to the S-Video mode.
C. Please use shielded scart cable.
S-Video/Audio in sockets (S-Video)
PC INPUT
ANT IN ( 75 ) PC SOUND
AV 1
H/P
AV 2
S-VIDEO
S-VIDEO VCR
26
When connecting an S-VIDEO VCR to the S-VIDEO socket, the
picture quality will be further improved.
1. Connect the S-Video socket of the VCR to the S-VIDEO socket
of the set.
2. Connect the audio cable from the S-VIDEO VCR to the AUDIO
sockets of the set.
3. Press the INPUT button to select AV2.
4. Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Connection of external equipment
Euro scart socket (DVD)
PC INPUT
ANT IN ( 75 ) PC SOUND
AV 1
1. Connect the Euro scart socket of the DVD to the Euro scart
socket of the set.
2. Press the INPUT button to select AV1.
3. Press the PLAY button on the DVD.
The DVD playback picture appears on the screen.
H/P
AV 2
S-VIDEO
DVD
DVD input sockets (23LC1R*)
COMPONENT
L
R
AUDIO
VIDEO
1. Connect the DVD output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y
or Y PB PR) of the DVD to the COMPONENT/VIDEO sockets (Y
PB PR) of the set.
2. Connect the audio cable from the DVD to COMPONENT/
AUDIO sockets of the set.
3. Press the INPUT button to select Component.
4. Press the PLAY button on the DVD.
The DVD playback picture appears on the screen.
DVD
DTV in sockets (15/23LC1R*)
PC INPUT
ANT IN ( 75 )
PC SOUND
AV 1
H/P
1. Connect the SET TOP outputs to the COMPONENT/VIDEO
sockets (Y PB PR) on the set. (or, connect the SET TOP with the
D-Sub output socket to PC INPUT socket on the set and audio
cable of the SET TOP to the PC SOUND. (15/23LC1R*))
2. Connect the audio cable from the SET TOP to COMPONENT/
AUDIO sockets of the set.
3. Press the INPUT button to select Component (23LC1R* only)
or RGB-DTV (15/23LC1R*).
S-VIDEO
AV 2
DTV Reciever
AUDIO
1. Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set.
2. Press the INPUT button to select AV2.
3. Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
R
Audio/Video in sockets
L
VIDEO
COMPONENT
DTV Reciever
Note : If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket of the set.
PC INPUT
ANT IN ( 75 ) PC SOUND
AV 1
H/P
AV 2
S-VIDEO
Headphone socket
VCR
Insert the headphone plug to the headphone socket of the set. You
can listen to the sound through the headphone. To adjust the headphone volume, press the F / G button. If you press the MUTE button, the sound from the headphone is switched off.
PC INPUT
ANT IN ( 75 ) PC SOUND
AV 1
H/P
AV 2
S-VIDEO
27
Connection of PC
PC INPUT
ANT IN ( 75 ) PC SOUND
AV 1
H/P
AV 2
S-VIDEO
PERSONAL COMPUTER
PC in socket (15/23LC1R*)
1. Connect the signal cable from the monitor output socket of the
PERSONAL COMPUTER to the PC input socket of the set.
2. Connect the audio cable from the PC to the PC SOUND
sockets of the set.
3. Press the INPUT button to select RGB-PC.
4. Switch on the PC, and the PC screen appears on the set.
The set can be operated as the PC monitor.
Displayable Monitor Specification
MODE Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
VGA
640x480
31.4
60
SVGA
800x600
800x600
35.1
37.8
56
60
XGA
1024x768
48.3
60
WXGA
1360x768
47.6
60
23” only
(Synchronization input form : separate)
Note :
a. If the set is cold, there may be a small “flicker” when the set is switched on. This is normal, there
is nothing wrong with the set.
b. If possible, use the VESA 1024x768@60Hz (15") / 1360x768@60Hz (23”) video mode to obtain the
best image quality for your LCD monitor. If used under the other resolutions, some scaled or
processed pictures may appear on the screen. The set has been pre-adjusted to the mode VESA
1024x768@60Hz (15") / 1360x768@60Hz (23”).
c. Some dot defects may appear on the screen, like Red, Green or Blue spots. However, this will have
no impact or effect on the monitor performance.
d. Do not press the LCD screen with your finger for a long time as this may produce some temporary
distortion effects on the screen.
e. When the PC screen appears on the set, a message may appear on the screen, and the message
will differ according to the Window system version. If a message appears click “Next” until the
message finishes.
f. If the message “out of range” appears on the screen, adjust the PC as in the ‘Displayable Monitor
Specification’ section.
DPM (Display Power Management) mode
When the PC is in the power saving mode, automatically the monitor goes into DPM mode to save the
energy.
Note : Use the supplied signal cable with the set. Otherwise, DPM mode may not work.
28
Connection of PC
PC Setup (15/23LC1R*)
SCREEN
ARC *
Auto configure
Manual configure
Reset
D
E
MENU
FG
You can adjust auto configure, manual configure and reset as you
prefer.
OK
* : 23LC1R* only
1. Press the INPUT button and then D / E button to select the
RGB-PC.
2. Press the MENU button and then D / E button to select the
SCREEN menu.
3. Press the G button and then D / E button to select the desired
screen function.
SCREEN
ARC *
Auto configure
Manual configure
Reset
To start
INPUT
D
E
MENU
MENU
FG
OK
4. Make appropriate adjustments.
Auto configure
This function is for the automatic adjustment of the screen position, clock and phase. The displayed image will disappear for a
few seconds while the Auto-configuration is in progress.
PR
OK
VOL
VOL
Manual configure
PR
This function is for the manual adjustment of the screen position, clock and phase. Press the F / G button to make appropriate adjustments.
• H-Position / V-Position
This function is to adjust picture to left/right and up/down as you
prefer.
SSM
PSM
• Clock
This function is to minimize any vertical bars or stripes visible on
the screen background. And the horizontal screen size will also
change.
• Phase
This function allows you to remove any horizontal noise and
clear or sharpen the image of characters.
Reset
This function allows you to return to the good picture reproduction programmed at the factory and cannot be changed.
Note : Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your monitor’s position, clock and phase manually.
5. Press the OK button to store it for the PC monitor picture.
29
Connection of PC
Picture format (23LC1R* only)
You can watch TV in various picture formats; Full, 16:9, 14:9,
Zoom, Spectacle, Original, 4:3.
Repeatedly press the ARC button to select your desired picture
format.
Full
When your TV receives the wide screen signal, it will lead you to
adjust the picture horizontally or vertically, in a linear proportion, to
fill the entire screen fully. (Not available in all countries)
TV
MENU
16:9
You can enjoy the cinema (the picture format of 16:9) or general TV
programme through the 16:9 mode.
The screen 16:9 is viewed just like that but the screen 4:3 is
magnified to the left and right so that the screen 16:9 is full.
14:9
You can enjoy the picture format of 14:9 or general TV programme
through the 14:9 mode.
The screen 14:9 is viewed just like that the screen 4:3 is magnified
to the upper / lower and left / right.
PR
OK
VOL
VOL
PR
Zoom
You can enjoy the cinema in a vast screen through the Zoom mode.
The screen 4:3 is magnified to the upper / lower and left / right sides
so that the screen 16:9 is full. The bottom and top of the picture
may be lost.
Spectacle
When your TV receives the wide screen signal, it will lead you to
adjust the picture horizontally, in a nonlinear proportion, to fill the
entire screen.
ARC
Original
When your TV receives the wide screen signal, it will be automatically
changed to the picture format to be sent. (Not available in all countries)
4:3
This picture format is 4 to 3 of general TV.
Note : ARC menu is not available in RGB-PC mode.
30
Troubleshooting Checklist
The operation does not work normally.
The remote control
doesn’t work
• Check to see if there is any object between the product and the remote
control causing obstruction.
• Are batteries installed with correct polarity (+ to +, - to -)?
• Correct remote operating mode set: TV, VCR etc.?
• Install new batteries.
Power is suddenly
turned off
• Is the sleep timer set?
• Check the power control settings. Power interrupted
• No broadcast on station tuned with Auto off activated.
The video function does not work.
No picture &
No sound
• Check whether the product is turned on.
• Try another channel. The problem may be with the broadcast.
• Is the power cord inserted into wall power outlet?
• Check your antenna direction and/or location.
• Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
Picture appears
slowly after
switching on
• This is normal, the image is muted during the product startup process.
Please contact your service center, if the picture has not appeared after five
minutes.
No or poor color
or poor picture
• Adjust Color in menu option.
• Keep a sufficient distance between the product and the VCR.
• Try another channel. The problem may be with the broadcast.
• Are the video cables installed properly?
• Activate any function to restore the brightness of the picture.
Horizontal/vertical bars or picture shaking
• Check for local interference such as an electrical appliance or power tool.
Poor reception on
some channels
Lines or streaks
in pictures
• Station or cable product experiencing problems, tune to another station.
• Station signal is weak, reorient antenna to receive weaker station.
• Check for sources of possible interference.
• Check antenna (Change the direction of the antenna).
31
The audio function does not work.
Picture OK &
No sound
No output from one
of the speakers
Unusual sound
from inside the
product
• Press the VOL (or Volume) button.
• Sound muted? Press MUTE button.
• Try another channel. The problem may be with the broadcast.
• Are the audio cables installed properly?
• Adjust Balance in menu option.
• A change in ambient humidity or temperature may result in an unusual
noise when the product is turned on or off and does not indicate a fault with
the product.
There is a problem in PC mode.
(Only PC mode applied)
The signal is out of
range.
• Adjust resolution, horizontal frequency, or vertical frequency.
• Check it whether the signal cable is connected or loose.
• Check the input source.
Vertical bar or
stripe on background &
Horizontal Noise &
Incorrect position
• Work the Auto configure or adjust clock, phase, or H/V position.
Screen color is
unstable or single
color
• Check the signal cable.
• Reinstall the PC video card.
Product Specifications
Power Requirement/
Power Consumption
Dimensions
(Width x Depth x Height)
Weight (Net)
Television System
Programme Coverage
External Antenna Impedance
15LC1R*
20LC1R*
23LC1R*
15LC1R*
: AC100-240V~ 50/60Hz 0.8A / 40W
: AC100-240V~ 50/60Hz 1.2A / 65W
: AC100-240V~ 50/60Hz 1.4A / 120W
: 377.6mm x 242.8mm x 394.5mm
14.9inches x 9.6inches x 15.5inches
20LC1R* : 492.2mm x 272.8mm x 483.3mm
19.3inches x 10.7inches x 19.0inches
23LC1R* : 611.0mm x 273.0mm x 485.0mm
24.0inches x 10.7inches x 19.0inches
15LC1R* : 5.6kg (12.3lbs)
20LC1R* : 8.7kg (19.1lbs)
23LC1R* : 10.4kg (22.9lbs)
PAL/SECAM B/G/D/K, PAL I/II, SECAM L/L’
VHF: E2 ~ E12, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S47
75 Ω
* The specifications shown above may be changed without prior notice for quality improvement.
Download PDF