LG | 26LN4500 | LG 26LN4500 Owner’s Manual

OWNER’S MANUAL
LED TV
*LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating
your set and retain it for future reference.
LN45**
P/NO : MFL67605616 (1302-REV00)
Printed in Korea
www.lg.com
2
TABLE OF CONTENTS
ENGLISH
ENG
TABLE OF CONTENTS
3
SAFETY INSTRUCTIONS
30
OPEN SOURCE SOFTWARE NOTICE
8
INSTALLATION PROCEDURE
30
EXTERNAL CONTROL DEVICE
SETUP
8
ASSEMBLING AND PREPARING
8
11
12
13
13
13
14
15
16
Unpacking
Parts and buttons
Lifting and moving the TV
Setting up the TV
- Attaching the Stand Base
- Detaching the Stand Base
Mounting on a table
Mounting on a wall
Tidying cables
17
MAKING CONNECTIONS
17 Antenna connection
18Adapter connection
18 HDMI connection
19 DVI to HDMI connection
19 RGB connection
20 Component connection
20 Composite connection
21 Headphone connection
21 MHL connection
22 USB connection
23
REMOTE CONTROL
24
USING THE USER GUIDE
25
MAINTENANCE
25
25
25
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
25
TROUBLESHOOTING
26
ENVIRONMENTAL INFORMATION
26
WEEE
27
SPECIFICATIONS
30
LICENSES
WARNING
yy If you ignore the warning message, you may
be seriously injured or there is a possibility of
accident or death.
CAUTION
yy If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
yy The note helps you understand and use the
product safely. Please read the note carefully
before using the product.
SAFETY INSTRUCTIONS
ENGLISH
ENG
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
yyDo not place the TV and
remote control in the following
environments:
--A location exposed to
direct sunlight
--An area with high humidity
such as a bathroom
--Near any heat source
such as stoves and other
devices that produce heat
--Near kitchen counters or
humidifiers where they can
easily be exposed to steam
or oil
--An area exposed to rain or
wind
--Near containers of water
such as vases
Otherwise, this may result in
fire, electric shock, malfunction
or product deformation.
yyDo not place the product
where it might be exposed to
dust.
This may cause a fire hazard.
yyMains Plug is the
TV connecting/
disconnecting device to AC
mains electric supply. This
plug must remain readily
attached and operable when
TV is in use.
yyDo not touch the power plug
with wet hands. Additionally, if
the cord pin is wet or covered
with dust, dry the power plug
completely or wipe dust off.
You may be electrocuted due
to excess moisture.
yyMake sure to connect Mains
cable to compliant AC mains
socket with Grounded earth
pin. (Except for devices which
are not grounded on earth.)
Otherwise possibility you
may be electrocuted or
injured.
3
yyInsert power cable plug
completely into wall socket
otherwise if not secured
completely into socket, fire
ignition may break out.
yyEnsure the power cord does
not come into contact with
hot objects such as a heater.
This may cause a fire or an
electric shock hazard.
yyDo not place a heavy object,
or the product itself, on power
cables.
Otherwise, this may result in
fire or electric shock.
yyBend antenna cable between
inside and outside building to
prevent rain from flowing in.
This may cause water
damaged inside the Product
and could give an electric
shock.
yyWhen mounting TV onto wall
make sure to neatly install
and isolate cabling from
rear of TV as to not create
possibility of electric shock /
fire hazard.
yyDo not plug too many
electrical devices into a single
multiple electrical outlet.
Otherwise, this may result in
fire due to over-heating.
yyDo not drop the product or let
it fall over when connecting
external devices.
Otherwise, this may result
in injury or damage to the
product.
4
SAFETY INSTRUCTIONS
ENGLISH
ENG
yyKeep the packing antimoisture material or vinyl
packing out of the reach of
children.
Anti-moisture material is
harmful if swallowed. If
swallowed by mistake, force
the patient to vomit and
visit the nearest hospital.
Additionally, vinyl packing can
cause suffocation. Keep it out
of the reach of children.
yyDo not spray water on the
product or scrub with an
inflammable substance
(thinner or benzene). Fire or
electric shock accident can
occur.
yyDo not let your children climb
or cling onto the TV.
Otherwise, the TV may
fall over, which may cause
serious injury.
yyNever touch this product or
antenna during a thunder or
lighting storm.
You may be electrocuted.
yyDispose of used batteries
carefully to protect a child
from eating them.
Please seek Doctor- Medical
Attention immediately if child
consumes batteries.
yyDo not insert any metal
objects/conductors (like
a metal chopstick/cutlery/
screwdriver) between power
cable plug and input Wall
Socket while it is connected
to the input terminal on the
wall. Additionally, do not
touch the power cable right
after plugging into the wall
input terminal.
You may be electrocuted.
(Depending on model)
yyDo not put or store
inflammable substances
near the product. There is
a danger of combustion/
explosion or fire due to
careless handling of the
inflammable substances.
yyDo not drop metallic objects
such as coins, hair pins,
chopsticks or wire into the
product, or inflammable
objects such as paper and
matches. Children must pay
particular attention.
Electrical shock, fire or injury
can occur. If a foreign object
is dropped into the product,
unplug the power cord and
contact the service centre.
yyDo not allow any impact,
shock or any objects to fall
into the unit, and do not drop
anything onto the screen.
You may be injured or the
product can be damaged.
yyNever touch the wall outlet
when there is leakage of
gas, open the windows and
ventilate.
It may cause a fire or a burn
by a spark.
yyDo not disassemble, repair
or modify the product at your
own discretion.
Fire or electric shock accident
can occur.
Contact the service centre for
check, calibration or repair.
yyIf any of the following
occur, unplug the product
immediately and contact your
local service centre.
--The product has been
impacted by shock
--The product has been
damaged
--Foreign objects have
entered the product
--The product produced
smoke or a strange smell
This may result in fire or
electric shock.
SAFETY INSTRUCTIONS
yyApparatus shall not be
exposed to dripping or
splashing and no objects
filled with liquids, such as
vases, shall be placed on the
apparatus.
CAUTION
yyInstall the product where no
radio wave occurs.
yyThere should be enough
distance between an outside
antenna and power lines
to keep the former from
touching the latter even when
the antenna falls.
This may cause an electric
shock.
yyDo not install the product
on places such as unstable
shelves or inclined surfaces.
Also avoid places where
there is vibration or where
the product cannot be fully
supported.
Otherwise, the product may
fall or flip over, which may
cause injury or damage to the
product.
yyIf you install the TV on a
stand, you need to take
actions to prevent the product
from overturning. Otherwise,
the product may fall over,
which may cause injury.
yyIf you intend to mount the product to a wall,
attach VESA standard mounting interface
(optional parts) to the back of the product. When
you install the set to use the wall mounting
bracket (optional parts), fix it carefully so as not
to drop.
yyOnly use the attachments / accessories specified
by the manufacturer.
yyWhen installing the antenna,
consult with a qualified
service technician. If not
installed by a qualified
technician, this may create
a fire hazard or an electric
shock hazard.
yyWe recommend that you
maintain a distance of at least
2 to 7 times the diagonal
screen size when watching
TV.
If you watch TV for a long
period of time, this may
cause blurred vision.
yyOnly use the specified type of
battery.
This could cause damage to
the remote control.
yyDo not mix new batteries with
old batteries.
This may cause the batteries
to overheat and leak.
yyBatteries should not be exposed to excessive
heat.eg keep away from direct Sunlight, open
fireplace and electric heaters.
yyDo not place non-rechargeable batteries in
charging device.
yyMake sure there are no
objects between the remote
control and its sensor.
yySignal from Remote Control
can be interrupted due to
external/internal lighting eg
Sunlight, fluorescent lighting.
If this occurs turn off lighting
or darken viewing area.
yyWhen connecting external
devices such as video game
consoles, make sure the
connecting cables are long
enough.
Otherwise, the product may
fall over, which may cause
injury or damage the product.
yyDo not turn the product
On/Off by plugging-in or
unplugging the power plug to
the wall outlet. (Do not use
the power plug for switch.)
It may cause mechanical
failure or could give an
electric shock.
ENGLISH
ENG
yyUnplug the TV from AC
mains wall socket if you do
not intend to use the TV
for a long period of time.
Accumulated dust can cause
fire hazard and insulation
deterioration can cause
electric leakage/shock/fire.
5
6
SAFETY INSTRUCTIONS
ENGLISH
ENG
yyPlease follow the installation
instructions below to prevent
the product from overheating.
--The distance between the
product and the wall should
be more than 10 cm.
--Do not install the product in
a place with no ventilation
(e.g., on a bookshelf or in
a cupboard).
--Do not install the product
on a carpet or cushion.
--Make sure the air vent is
not blocked by a tablecloth
or curtain.
Otherwise, this may result in
fire.
yyTake care not to touch the
ventilation openings when
watching the TV for long
periods as the ventilation
openings may become hot.
This does not affect the
operation or performance of
the product.
yyPeriodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized servicer.
yyPrevent dust collecting on the
power plug pins or outlet.
This may cause a fire hazard.
yyProtect the power cord from
physical or mechanical
abuse, such as being twisted,
kinked, pinched, closed in a
door, or walked upon. Pay
particular attention to plugs,
wall outlets, and the point
where the cord exits the
appliance.
yyDo not press strongly upon
the panel with a hand or
sharp object such as nail,
pencil or pen, or make a
scratch on it, as it may
cause damage to screen.
yyAvoid touching the screen or
holding your finger(s) against
it for long periods of time.
Doing so may produce some
temporary or permanent
distortion/damage to screen.
yyWhen cleaning the product
and its components, unplug
the power first and wipe it
with a soft cloth. Applying
excessive force may cause
scratches or discolouration.
Do not spray with water or
wipe with a wet cloth. Never
use glass cleaner, car or
industrial shiner, abrasives
or wax, benzene, alcohol
etc., which can damage the
product and its panel.
Otherwise, this may result in
fire, electric shock or product
damage (deformation,
corrosion or breakage).
yyAs long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
yyWhen unplugging the cable,
grab the plug and unplug it,
by pulling at the plug. Don’t
pull at the cord to unplug the
power cord from the power
board, as this could be
hazardous.
yyWhen moving the product,
make sure you turn the power
off first. Then, unplug the
power cables, antenna cables
and all connecting cables.
The TV set or power cord
may be damaged, which may
create a fire hazard or cause
electric shock.
yyWhen moving or unpacking
the product, work in pairs
because the product is heavy.
Otherwise, this may result in
injury.
SAFETY INSTRUCTIONS
yyRefer all servicing to
qualified service personnel.
Servicing is required when
the apparatus has been
damaged in any way, such
as power supply cord or
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus, the
apparatus has been exposed
to rain or moisture, does not
operate normally, or has been
dropped.
yyIf the product feels cold to the
touch, there may be a small
“flicker” when it is turned
on. This is normal, there is
nothing wrong with product.
yyThe panel is a high
technology display product
with resolution of two million
to six million pixels. You
may see tiny black dots and/
or brightly coloured dots
(red, blue or green) at a
size of 1 ppm on the panel.
This does not indicate a
malfunction and does not
affect the performance and
reliability of the product.
This phenomenon also occurs
in third-party products and is
not subject to exchange or
refund.
yyYou may find different
brightness and colour of the
panel depending on your
viewing position(left/right/top/
down).
This phenomenon occurs due
to the characteristic of the
panel. It is not related with
the product performance, and
it is not malfunction.
ENGLISH
ENG
yyContact the service centre
once a year to clean the
internal parts of the product.
Accumulated dust can cause
mechanical failure.
7
yyDisplaying a still image (e.g., broadcasting
channel logo, on-screen menu, scene from a
video game) for a prolonged time may cause
damage to the screen, resulting in retention of
the image, which is known as image sticking. The
warranty does not cover the product for image
sticking.
Avoid displaying a fixed image on your
television’s screen for a prolonged period (2
or more hours for LCD, 1 or more hours for
Plasma).
Also, if you watch the TV at a ratio of 4:3 for
a long time, image sticking may occur on the
borders of the panel.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
yyGenerated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to temperature and humidity. This noise is common for
products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a high-speed
switching circuit, which supplies a large amount
of current to operate a product. It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
8
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENGLISH
ENG
NOTE
yy
yy
yy
yy
yy
Image shown may differ from your TV.
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
The available menus and options may differ from the input source or product model that you are using.
New features may be added to this TV in the future.
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned
off if it will not be watched for some time, as this will reduce energy consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced,
and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to upgrade of product
functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm
width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your
TV’s USB port.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
ASSEMBLING AND PREPARING
9
ENGLISH
ENG
or
Remote control and
batteries (AAA)
( See p.23)
Owner’s manual
Cable Tie
(Depending on model)
( See p.16)
Isolator
(Depending on model)
( See p.10)
AC-DC Adapter
(Depending on model)
( See p.18)
Stand Base
( See p.13)
or
Power Cord
AC-DC Adapter
(Depending on model)
( See p.18)
( See p.18)
10
ASSEMBLING AND PREPARING
ENGLISH
ENG
NOTE
yy Antenna Isolator Installation Guide
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be
heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is
recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid
disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
1. Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
2. Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a cable
distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection
to a cable distribution system has therefore to be provided through a device providing electrical
isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ASSEMBLING AND PREPARING
ENGLISH
ENG
Parts and buttons
Screen
Remote control Sensor
Speakers
OK
SETTINGS
INPUT
Touch buttons1
Touch Buttons
Description
Scrolls through the saved programmes.
H
Adjusts the volume level.
H
11
OK ꔉ
Selects the highlighted menu option or confirms an input.
SETTINGS
Accesses the main menu, or saves your input and exits the menus.
INPUT
Changes the input source.
/I
Turns the power on or off.
1 All of the buttons are touch sensitive and can be operated through simple touch with your finger.
12
ASSEMBLING AND PREPARING
ENGLISH
ENG
Lifting and moving the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for safe
transportation regardless of its type and size.
yy When transporting a large TV, there should be
at least 2 people.
yy When transporting the TV by hand, hold the TV
as shown in the following illustration.
CAUTION
yy Avoid touching the screen at all times, as this may
result in damage to the screen.
yy It is recommended to move the TV in the box
or packing material that the TV originally came
in.
yy Before moving or lifting the TV, disconnect the
power cord and all cables.
yy When holding the TV, the screen should face
away from you to avoid damage.
yy Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
yy When transporting the TV, do not expose the
TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the
left or right.
yy Do not apply excessive pressure to cause
flexing /bending of frame chassis as it may
damage screen.
ASSEMBLING AND PREPARING
13
ENGLISH
ENG
Setting up the TV
Image shown may differ from your TV.
Attaching the Stand Base
1
Detaching the Stand Base
1
Stand Base
Stand Base
NOTE
yy When Detaching the stand from TV, Detach the
stand with lifting up the lever in the direction of the
arrow.
2
2
CAUTION
yy Lay a foam mat or soft protective cloth on the
surface to protect the screen from damage.
yy When attaching the stand to the TV set, place the
screen facing down on a cushioned table or flat
surface to protect the screen from scratches.
CAUTION
yy Lay a foam mat or soft protective cloth on the
surface to protect the screen from damage.
yy When Detaching the stand to the TV set, place the
screen facing down on a cushioned table or flat
surface to protect the screen from scratches.
14
ASSEMBLING AND PREPARING
ENGLISH
ENG
Mounting on a table
1 Lift and tilt the TV into its upright position on a table.
-- Leave a 10 cm (minimum) space from the wall
for proper ventilation.
CAUTION
yy Make sure that children do not climb on or hang
on the TV.
NOTE
10 cm
10 cm
m
10 c
10 cm
yy Use a platform or cabinet that is strong and large
enough to support the TV securely.
yy Brackets, bolts and ropes are not provided. You
can obtain additional accessories from your local
dealer.
WARNING
2 Connect the AC-DC Adapter and Power Cord to a
wall outlet.
CAUTION
yy Do not place the TV near or on sources of heat,
as this may result in fire or other damage.
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV brackets and
bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eyebolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly with a
sturdy rope.
Make sure to keep the rope horizontal with the flat
surface.
yy If a television is not positioned in a sufficiently
stable location, it can be potentially hazardous
due to falling. Many injuries, particularly to
children, can be avoided by taking simple
precautions such as:
»» Using cabinets or stands recommended by the
manufacturer of the television.
»» Only using furniture that can safely support the
television.
»» Ensuring the television is not overhanging the
edge of the supporting furniture.
»» Not placing the television on tall furniture (for
example, cupboards or bookcases) without
anchoring both the furniture and the television
to a suitable support.
»» Not standing the televisions on cloth or other
materials placed between the television and
supporting furniture.
»» Educating children about the dangers of
climbing on furniture to reach the television or
its controls.
ASSEMBLING AND PREPARING
(This feature is not available for all models.)
The Kensington security system connector is located at
the rear of the TV. For more information of installation and
using, refer to the manual provided with the Kensington
security system or visit http://www.kensington.com.
Connect the Kensington security system cable between
the TV and a table.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the
TV carefully and install the wall mount bracket on a solid
wall perpendicular to the floor. When you attach the
TV to other building materials, please contact qualified
personnel.
LG recommends that wall mounting be performed by a
qualified professional installer.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that
meet the VESA standard. Standard dimensions for the
wall mount kits are described in the following table.
Separate purchase(Wall Mounting Bracket)
Model
22/24/26/28/29LN45**
VESA (A x B)
Standard screw
Number of screws
Wall mount bracket
100 x 100
M4
4
LSW130B
A
B
ENGLISH
ENG
Using the Kensington security system
15
16
ASSEMBLING AND PREPARING
ENGLISH
ENG
CAUTION
yy Disconnect the power first, and then move or
install the TV. Otherwise electric shock may occur.
yy If you install the TV on a ceiling or slanted wall, it
may fall and result in severe injury.
Use an authorized LG wall mount and contact the
local dealer or qualified personnel.
yy Do not over tighten the screws as this may cause
damage to the TV and void your warranty.
yy Use the screws and wall mounts that meet the
VESA standard. Any damages or injuries by
misuse or using an improper accessory are not
covered by the manufacturer’s warranty.
Tidying cables
Use Cable Tie to neatly secure and position cables
together.
NOTE
yy Use the screws that are listed on the VESA
standard screw specifications.
yy The wall mount kit includes an installation manual
and necessary parts.
yy The wall mount bracket is not provided. You can
obtain additional accessories from your local
dealer.
yy The length of screws may differ depending on the
wall mount. Make sure to use the proper length.
yy For more information, refer to the manual supplied
with the wall mount.
Cable Tie
CAUTION
yy Do not move the TV by holding the cable tie,
as the cable ties may break, and injuries and
damage to the TV may occur.
MAKING CONNECTIONS
This section on MAKING CONNECTIONS
mainly uses diagrams for the LN45** models.
Connect various external devices to the TV and switch
input modes to select an external device. For more
information of external device’s connection, refer to the
manual provided with each device.
Available external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
Antenna connection
Connect the TV to a wall antenna socket with an RF
cable (75 Ω).
NOTE
yy The external device connection may differ from
the model.
yy Connect external devices to the TV regardless of
the order of the TV port.
yy If you record a TV programme on a DVD recorder
or VCR, make sure to connect the TV signal input
cable to the TV through a DVD recorder or VCR.
For more information of recording, refer to the
manual provided with the connected device.
yy Refer to the external equipment’s manual for
operating instructions.
yy If you connect a gaming device to the TV, use the
cable supplied with the gaming device.
yy In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast or
brightness. If noise is present, change the PC
output to another resolution, change the refresh
rate to another rate or adjust the brightness and
contrast on the PICTURE menu until the picture is
clear.
yy In PC mode, some resolution settings may not
work properly depending on the graphics card.
ANTENNA
/CABLE IN
(*Not Provided)
NOTE
yy Use a signal splitter to use more than 2 TVs.
yy If the image quality is poor, install a signal
amplifier properly to improve the image quality.
yy If the image quality is poor with an antenna
connected, try to realign the antenna in the correct
direction.
yy An antenna cable and converter are not supplied.
yy Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus
ENGLISH
ENG
MAKING CONNECTIONS
17
18
MAKING CONNECTIONS
ENGLISH
ENG
Adapter connection
HDMI connection
Transmits the digital video and audio signals from an
external device to the TV. Connect the external device
and the TV with the HDMI cable as shown.
DC-IN
(19V
)
AC-DC Adapter
or
(MHL)
IN
DC-IN
(19V
)
(*Not Provided)
AC-DC Adapter
HDMI
CAUTION
yy Please be sure to connect the TV to the ACDC power adapter before connecting the TV’s
power plug to a wall power outlet.
DVD/ Blu-Ray / HD Cable Box / HD STB / PC
NOTE
yy It is recommended to use the TV with the HDMI
connection for the best image quality.
yy Use the latest High Speed HDMI™ Cable with
CEC (Customer Electronics Control) function.
yy High Speed HDMI™ Cables are tested to carry
an HD signal up to 1080p and higher.
yy Supported HDMI Audio format : Dolby Digital,
PCM (Up to 192 KHz, 32k/44.1k/48k/88k/96k/17
6k/192k) *DTS Not Supported.
MAKING CONNECTIONS
Transmits the digital video signal from an external device
to the TV. Connect the external device and the TV with
the DVI-HDMI cable as shown. To transmit an audio
signal, connect an audio cable.
Transmits the analog video signal from your PC to the
TV. Connect the PC and the TV with the D-sub 15 pin
cable. To transmit an audio signal, connect an audio
cable.
(MHL)
AUDIO
IN
(PC)
AUDIO
IN
(PC)
RGB connection
IN
RGB IN (PC)
(*Not Provided)
DVI OUT
(*Not Provided)
AUDIO OUT
RGB OUT(PC)
AUDIO OUT
DVD/ Blu-Ray / HD Cable Box / HD STB / PC
PC
NOTE
yy Depending on the graphics card, DOS mode
may not work if a HDMI to DVI Cable is in use.
NOTE
yy If you do not use an optional external speaker,
connect the PC to the TV with the optional audio
cable.
ENGLISH
ENG
DVI to HDMI connection
19
20
MAKING CONNECTIONS
ENGLISH
ENG
Component connection
Composite connection
Transmits analog video and audio signals from an
external device to the TV. Connect the external device
and the TV with a component cable as shown.
Transmits analog video and audio signals from an
external device to the TV. Connect the external device
and the TV with the composite cable as shown.
COMPONENT IN
VIDEO
COMPONENT IN
AUDIO
VIDEO
AUDIO
L
L
L
R
(MONO)
L
RED
WHITE
YELLOW
RED
WHITE
RED
BLUE
GREEN
R
VIDEO(MONO)
VIDEO
RED
WHITE
YELLOW
RED
WHITE
RED
BLUE
GREEN
(*Not Provided)
(*Not Provided)
L
R
(MONO)
L AUDIO R
AUDIO
DVD/ Blu-Ray / HD Cable Box / VCR
DVD/ Blu-Ray / HD Cable Box
NOTE
yy If cables are not installed correctly, it could cause
this image to display in black and white or with
distorted colours.
MAKING CONNECTIONS
Transmits the headphone signal from the TV to
an external device. Connect the external device
and the TV with the headphone as shown.
Mobile High-definition Link (MHL) is an interface for
transmitting digital audiovisual signals from mobile
phones to television sets.
H/P
MHL connection
(MHL)
(*Not Provided)
NOTE
yyAUDIO menu items are disabled when connecting
a headphone.
yyWhen changing AV MODE with a headphone
connected, the change is applied to video but not
to audio.
yyHeadphone impedance: 16 Ω
yyMax audio output of headphone: 9 mW to 15 mW
yyHeadphone jack size: 0.35 cm
IN
MHL passive cable
(*Not Provided)
Mobile phone
NOTE
yyConnect the mobile phone to the HDMI IN (MHL)
port to view the phone screen on the TV.
yyThe MHL passive cable is needed to connect the
TV and a mobile phone.
yyThis only works for the MHL-enabled phone.
yySome applications can be operated by the remote
control.
yyRemove the MHL passive cable from the TV
when:
-- The MHL function is disabled.
-- Your mobile device is fully charged in standby
mode.
ENGLISH
ENG
Headphone connection
21
22
MAKING CONNECTIONS
Connect a USB storage device such as a USB flash
memory, external hard drive, or a USB memory card
reader to the TV and access the My media menu to use
various multimedia files.
USB IN
5V
0.5A
ENGLISH
ENG
USB connection
USB
(*Not Provided)
REMOTE CONTROL
23
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the
ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
ENGLISH
ENG
REMOTE CONTROL
and
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
yyIn Analogue TV and some countries, some remote control buttons may not work.
Make sure to point the remote control toward the remote control sensor on the TV.
(POWER)
TV/
RAD
INPUT
SUBTITLE
1
4
7
LIST
AD/PIP
2
5
8
0
3
6
9
Q.VIEW
FAV
GUIDE
P
MUTE
1
TEXT
INFO
SETTINGS
T.OPT
Q.MENU
EXIT
TV/PC
2
Turns the TV on or off.
TV/RAD
SUBTITLE
Selects Radio, TV and DTV programme.
AD/PIP
AD : Switches the Audio Description On or Off.
PIP : Turns the PIP mode on or off.
Recalls your preferred subtitle in digital mode.
(User Guide)
INPUT
Sees user-guide.
Number buttons
Enters numbers.
LIST
Accesses the saved programme list.
Q.VIEW
Returns to the previously viewed programme.
FAV
Accesses your favourite programme list.
GUIDE
Shows programme guide.
MUTE
Mutes all sounds.
Changes the input source.
Adjusts the volume level.
P
Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
1 TELETEXT BUTTONS
These buttons are used for teletext.
INFO
Views the information of the current programme and
screen.
SETTINGS
Accesses the main menus.
Q.MENU
Accesses the Quick menus.
Navigation buttons (up/
down/left/right)
Scrolls through menus or options.
OK
BACK
Selects menus or options and confirms your input.
EXIT
Clears on-screen displays and return to TV viewing.
Returns to the previous level.
Accesses the AV devices connected with the
HDMI cable through HDMI-CEC.
Opens the SIMPLINK menu.
TV/PC
Selects TV or PC mode.
Control buttons
(
)
Controls the MY MEDIA menus, or the SIMPLINK
compatible devices (USB,SIMPLINK).
2 Coloured buttons
These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
(Backlight)
Adjusts the brightness of the screen by controlling the
screen backlight.
24
USING THE USER GUIDE
ENGLISH
ENG
USING THE USER GUIDE
User Guide allows you to more easily access the detailed TV information.
Press SETTINGS to access the main menus.
Press the RED button to access the Customer
Support menus.
Press the Navigation buttons to scroll to User Guide
and press OK.
1
2
3
User Guide
1
PROGRAMME Setting
PICTURE, SOUND Setting
OPTION
OPTION > To set language
SETTINGS  OPTION  Language
You can select the language of the menu displayed on the screen and the digital
sound broadcasting.
y Menu Language : Selects a language for the display text.
y Audio Language [In Digital mode Only] : Select the desired language when
watching digital broadcasting containg several voice languages.
y Subtitle Language [In Digital mode Only] : Use the Subtitle function when two
or more subtitle languages are broadcast.
✎ If subtitle data in a selected language is not broadcast, the default
language subtitle will be displayed.
Advanced Function
PICTURE
AUDIO
SETUP
TIME
LOCK
OPTION
INPUT
MY MEDIA
Press OK() to set picture settings.
Customer Support
Information
FAQ
2
Zoom In
Close
SETTINGS  OPTION  Language
You can select the language of the menu displayed on the screen and the digital
sound broadcasting.
yy Menu Language : Selects a language for the display text.
yy Audio Language [In Digital mode Only] : elect the desired language when
watching digital broadcasting containg several voice languages.
yy Subtitle Language [In Digital mode Only] : Use the Subtitle function when two
or more subtitle languages are broadcast.
✎ If subtitle data in a selected language is not broadcast, the default
language subtitle will be displayed.
Exit
Software Update
Picture Test
Sound Test
Signal Test
2
Product/Service Info.
Zoom Out
Close
User Guide
Close
User Guide
3
2
To use input device
To set ODC (Over Driving Circuit)
PROGRAMME Setting
To use PIP (Picture In Picture)
PICTURE, SOUND Setting
To set time options
OPTION
To set TV lock options
Advanced Function
To set language
Information
1
To set country
1
Allows to select the category you want.
2
Allows to select the item you want.
You can use ꕌ/ꕍ to move between pages.
3
Allows to browse the description of the function
you want from the index.
1
Shows the description of the selected menu.
You can use ꕌ/ꕍ to move between pages.
2
Zooms in or out the screen.
MAINTENANCE / TROUBLESHOOTING
ENGLISH
ENG
MAINTENANCE
25
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yy Make sure to turn the power off and disconnect the power cord and all other cables first.
yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to
prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in scratches
and image distortions.
yy Do not use any chemicals as this may damage the product.
yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Problem
Solution
Cannot control the
TV with the remote
control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
to ,
to
yy Check if the batteries are still working and properly installed (
No image display and
no sound is produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Auto sleep feature is activated in the Time settings.
yy If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes
of inactivity.
When connecting to
the PC (RGB/HDMI),
‘No signal’ or ‘Invalid
Format’ is displayed.
yy Turn the TV off/on using the remote control.
yy Reconnect the RGB/HDMI cable.
yy Restart the PC with the TV on.
).
26
ENVIRONMENTAL INFORMATION
ENGLISH
ENG
ENVIRONMENTAL INFORMATION
(India only)
WEEE
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product
is covered by the e-waste (Management and Handling) Rules, 2011.
2. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the government
or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal
service or the shop where you purchased the product.
5. This product does not contain any of the hazardous substances as specified in the rule 13 (1) and (2) of
the e-waste (Management and Handling) Rules, 2011.
i;kZoj.kh; tkudkjh
WEEE
vius iqjkus midj.k dk fuiVku
ƒ. tc ;g dkVs x;s ifg;s okys fcu dk fpg+u fdlh mRikn ds lkFk layXu gksrk gS rks bldk vFkZ gS mRikn
¼izca/ku vkSj gFkkyu½ fu;e „Œƒƒ ds varxZr lfEefyr fd;k x;k gSA
„. lHkh bysfDVªdy ,oa vkSj bysDVªkfud mRiknkas dks ljdkj ;k LFkkuh; vf/kdkfj;ksa }kjk fu;qDr uxjikfydk
ls vyx izkf/kd`r dh xbZ laxzg lqfo/kkvksa ds ek/;e ls fuiVk;k tkuk pkfg,A
/kkjk …. lgh rjhds ls vius iqjkus midj.kksa dk fuiVku okrkoj.k vkSj ekuoh; LokLF; dss fy, laHkkfor udkjkRed ifj.kkeksa dks jksdus esa enn djsxkA
†. vius iqjkus midj.kksa ds fuiVku ds lac/k esa vkSj vf/kd folr`r tkudkjh ds fy,] d`i;k vius uxj dk;kZy;]
ls vkius mRikn [kjhnk Fkk] ogka laidZ djsaA
‡. bl mRikn esa
fuiVku lsok ;k tgka ¼izca/ku vkSj gFkkyu½ fu;e] „Œƒƒ ds fu;e ƒ… ¼ƒ½ vkSj ¼„½ esa funsZ’kkuqlkj dksbZ Hkh gkfudkjd inkFkZ “kkfey ugha gSA
SPECIFICATIONS
27
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
MODELS
22LN45**
24LN45**
26LN45**
22LN4500-TA
22LN4500-TB
24LN4500-TA
24LN4500-TB
26LN4500-TA
26LN4500-TB
Dimensions
(W x H x D)
With stand (mm)
513.0 x 362.0 x 140.0
557.0 x 390.0 x 140.0
621.0 x 431.0 x 162.1
Without stand(mm)
513.0 x 320.0 x 63.0
557.0 x 348.0 x 62.3
621.0 x 386.0 x 72.9
Weight
With stand (kg)
3.4
3.7
4.2
Without stand (kg)
3.2
3.5
4.0
Power requirement
19 V
19 V
19 V
AC/DC Adapter
Manufacturer : Lien Chang
Model : LCAP16B-E, LCAP16B-A, LCAP25B
Manufacturer : LG Innotek
Model : PSAB-L205B, PSAB-L205C, PSAB-L204B
Manufacturer : APD
Model : DA-40E19
MODELS
28LN45**
29LN45**
28LN4500-TA
28LN4500-TB
29LN4500-TA
29LN4500-TB
Dimensions
(W x H x D)
With stand (mm)
645.3 x 447.9 x 182.1
669.0 x 456.0 x 182.0
Without stand(mm)
645.3 x 401.6 x 78.7
669.0 x 411.0 x 82.0
Weight
With stand (kg)
5.2
5.8
Without stand (kg)
4.8
5.4
Power requirement
19 V
19 V
AC/DC Adapter
Manufacturer : Lien
Chang
Model : LCAP16B-E,
LCAP16B-A, LCAP25B
Manufacturer : LG
Innotek
Model : PSAB-L205B,
PSAB-L205C, PSABL204B
Manufacturer : APD
Model : DA-40E19
Manufacturer : LG
Innotek
Model : PSAB-L206A
Manufacturer : LG Innotek
Model : PSAB-L101A
Manufacturer : Lite-On
Model : PA-1650-64
ENGLISH
ENG
SPECIFICATIONS
28
SPECIFICATIONS
ENGLISH
ENG
Environment
condition
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Digital TV
New Zealand,
Singapore
Television System
Programme Coverage
Australia
Television System
Programme Coverage
Indonesia, Israel,
Myanmar, Sri
Lanka
Television System
Vietnam, Malaysia
Television System
Programme Coverage
Programme Coverage
Iran, Algeria,
Tunisia, Digital
model
Television System
Analogue model,
India, Thailand,
South Africa, --
Television System
Programme Coverage
Programme Coverage
External Antenna
Impedance
Analogue TV
DVB-T
PAL/SECAM-B/G/D/K, PAL-I
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
DVB-T
PAL B/B
VHF 06 to 12,
UHF 27 to 69
B/B : VHF/UHF 0 to 75, CATV : 2 to 44
DVB-T
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
DVB-T
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
VHF 6 to 12,
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
DVB-T
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
VHF 5 to 12,
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
-
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
-
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
75 Ω
75 Ω
29
SPECIFICATIONS
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
720 x 400
31.468
70.080
640 x 480
31.469
59.940
640 x 480
37.500
75.000
800 x 600
37.879
60.317
800 x 600
46.875
75.000
1024 x 768
48.363
60.004
1024 x 768
60.023
75.029
1280 x 800
49.702
59.810
1366 x 768
47.717
59.790
NOTE
yyThe optimal display resolution is
1366 X 768@60Hz.
yyThe optimal timing in each mode is vertical
frequency 60Hz.
HDMI-DTV supported mode
Resolution
Horizontal
Vertical
Frequency (kHz) Frequency (Hz)
720x480
31.469
31.500
59.940
60.000
720x576
31.250
50.000
1280x720
37.500
44.960
45.000
50.000
59.940
60.000
1920x1080
33.720
33.750
28.125
27.000
33.750
56.250
67.430
67.500
59.940
60.000
50.000
24.000
30.000
50.000
59.940
60.000
Component port connecting information
Component ports on the TV
Video output ports on DVD
player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
ENGLISH
ENG
RGB (PC) / HDMI (PC) supported mode
30
LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAl CONTROL DEVICE SETUP
ENGLISH
ENG
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of
Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.
com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order
to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code,
locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274”
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product,
please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for
download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is
valid for three (3) years from the date on which you purchased the product.
EXTERNAL CONTROL DEVICE SETUP
To obtain the external control device setup information, please visit www.lg.com
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring any
service.
MODEL
SERIAL
(Only DTV)
Download PDF

advertising