LG | LAC2800 | LG LAC2800 Owner’s Manual

LAC2800.DARELLR_ENG_MFL42688952
MODEL : LAC2800
Table of Contents
2
3
4
5
Table of Contents
Safety Note
Front Panel
About Detachable Control Panel
9
10
Pause or restart a CD
Search for a section within a track / file
Skip to another track / file
Intro scan
Repeat
Shuffle
MP3/WMA TRACK -10 / +10
MP3/WMA Folder UP/DOWN
See information about your music
Attaching the control panel
Detaching the control panel
6
Installation
Basic installation
Removing the existing receiver unit
ISO-DIN installation
7
8
Connection
Basic operation
Mute
Changing the general settings
Using the EQ
Adjusting the sound level
XDSS+
Checking the clock
Setting the clock
9
Listening to the radio
Auto search memory
Storing and recalling broadcast frequencies
To scan the preset stations
To tune in the preset stations
2
CAR CD/MP3/WMA Receiver
Connecting an Auxiliary Equipment
Listening a CD
11
12
Troubleshooting
Specifications
This product is manufactured to comply with Directive
2006/28/EEC(ANNEX I , 3.2.9), 72/245/EEC, and 2006/95/EC.
European representative :
LG Electronics Service Europe B.V. Veluwezoom 15, 1327
AE Almere, The Netherlands (Tel : +31-036-547-8940)
Safety Note
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : This product uses a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully
and retain it for future reference.
Should the unit require maintenance, contact an authorized service center.
Performing controls, adjustments, or carrying out procedures other than those
specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible
laser radiation when open. DO NOT STARE INTO BEAM.
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT SPLIT COVER(OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
Always operate the vehicle in a safe manner.
Do not become distracted by the vehicle while driving, and always be fully
aware of all driving condition. Do not change settings, or any functions.
Pull over in a safe and legal manner before attempting such operations.
Do not use for many hours at extremely low or high temperature.
(-10~60°C)
Caution
When being connected in a wrong way, the unit displays as follows.
1. Antenna port short : “ANTENNA ON PORT SHORT CIRCUIT CHECK”
After connecting it again, restart the unit.
You have to set the disc format option to [Mastered] in order to make the
discs compatible with the LG players when formatting rewritable discs.
When setting the option to Live File System, you cannot use it on LG players.
(Mastered/Live File System : Disc format system for Windows Vista)
To reduce the risk of electric shock, do not remove the cover or back of
this product. There are no user-serviceable parts inside.
Refer servicing to qualified service personnel.
To reduce the risk of fire or electric shock, do not expose this product to
dripping or splashing water, rain, or moisture.
The temperature of unit’s outside can be extremely high, please use the
unit after proper installation in your vehicle.
8 cm
This unit cannot play 8cm disc (use 12cm disc only).
CAR CD/MP3/WMA Receiver
3
Front Panel
1
2
3
[PWR]/[MUTE]
Volume UP/DOWN [+/-]
i
• Skip / Search I/i
i
• Seek/ Tune I/i
U/AS]
• Auto Store [U
u/PS]
• Preset Scan [u
u
• MP3/WMA Track +10/-10 U/u
u
• Folder Up/Down U/u
4
5
6
7
8
Disc slot
Display Window
Eject Z
Release
• [MENU]
• Display [DISP]
4
CAR CD/MP3/WMA Receiver
9
10
11
12
13
14
15
AUX In [AUX]
Preset Station [1-6]
Shuffle [SHF]
Repeat [RPT]
Intro Scan [INT]
Play/Pause B/X
• Equalizer [EQ]
• Extreme Dynamic Sound System [XDSS]
16 [BAND]
17 Source [SRC]
18 Select [SEL]
About Detachable Control Panel
Attaching the control panel
1
2
Detaching the control panel
Align the left side of the panel with
the stopper.
Push the right side or panel into the
unit until it clicks.
1
1
2
2
3
4
Press the “
” (RELEASE) to
open the control panel.
Hold the right part of the control
panel.
Pull out the control panel.
Place the control panel in the
supplied protective case.
2
3
1
Caution
• The control buttons may not work properly if the control panel is not attached
properly. If this occurs, gently press the display.
4
• Do not leave the control panel in any area exposed to high temperatures or
direct sunlight.
• Do not drop the control panel or otherwise subject it to strong impact.
• Do not allow such volatile agents as benzine, thinner, or insecticides to come
into contact with the surface of the control panel.
Control panel
Protective Case
Note
Periodically wipe the contacts on the back of the control
panel with a cotton swap moistened with alcohol. For safety,
turn off the ignition before cleaning, and remove the key
from the ignition switch.
CAR CD/MP3/WMA Receiver
5
Installation
ISO-DIN Installation
Basic Installation
1
2
3
4
Remove the existing receiver unit.
Make the necessary connections.
Install the installation sleeve.
Install the unit into the installation
sleeve.
Control panel
If there is already an installation
sleeve for the receiver unit in the
dashboard, it must be removed.
A
1
2
A
CAR CD/MP3/WMA Receiver
2
4
5
6
Control panel
Removing the existing receiver unit
6
1
Before installing, make sure that the
ignition-switch is set to OFF and
remove the terminal of the car battery
to avoid short-circuiting.
Bend the claws
according to
the thickness
of the
dashboard
3
Remove the rear support from the
unit.
Remove the control panel and trim
ring from the unit.
Insert the lever A into the hole on
one side of the unit.
Perform the same operation on
the other side and pull the unit out
from the mounting sleeve.
1
3
2
4
3
5
6
Slide the unit into the ISO-DIN
frame.
Fit screws removed from the old
unit.
Slide the unit and frame into the
dash opening.
Install the dash panel or adapter
plate.
Install the trim ring to the unit.
Install the control panel to the unit.
Connection
Before connecting, make sure that the ignition switch is set to OFF, and remove the battery # terminal to avoid short circuits.
1
3
5
7
2
4
6
8
1
3
5
7
2
4
6
8
B
A
Power
Antenna
A5
Power Antenna(Blue)
A6
Dimmer(Pink)
A7
To Ignition(Red)
Control Relay
Dimmer Switch
Ignition Switch
A4
To Battery(+)(Yellow)
B 1
A8
Ground(-)(Black)
B 2
B 3
BATTERY
A1, A2, A3 : Not connected
B
B
B
B
B
B
B
B
1
2
3
4
5
6
7
8
Violet : Rear Right +
Violet/ Black Stripe : Rear Right –
Gray : Front Right +
Gray / Black Stripe : Front Right –
White : Front Left +
White/Black Stripe : Front Left –
Green : Rear Left +
Green/ Black Stripe : Rear Left –
B 4
B 5
B 6
B 7
B 8
CAR CD/MP3/WMA Receiver
7
Basic Operation
ON PLAYER
1. Turn the unit on.
2. Select a source.
3. Adjust the volume.
PWR/MUTE
SRC
VOLUME + or -
Basic operation - more you can do
Mute
Note
When XDSS+ is set to “Off”, you can adjust the EQ settings.
Adjusting the sound level
Press SEL repeatedly to select the mode you want to adjust from volume, balance and fader.
Note
When EQ and XDSS+ is set to “Off”, you can adjust the sound level (BAS,
TRB) settings.
Press PWR/MUTE to cut the sound. To cancel it, press again.
XDSS+ (Extreme Dynamic Sound System)
Changing the general settings
Press and hold XDSS/EQ for more 2 seconds. (XDSS+ : Improves the treble,
bass sound.)
1 Press MENU so that one of menu items appears.
2 Press MENU and press + or - to select one of the settings specified belows.
3 Press and hold MENU finish the setting.
AUX (Auxiliary) ON / OFF
It is possible to use auxiliary equipment with this unit. Activate the auxiliary
setting when using auxiliary equipment connected to this unit.
AUX (Auxiliary) 00dB / +6dB
You can adjust the volume level of each source to prevent radical changes
in volume when switching between sources.
You can set to 0 dB or +6 dB. You may be surprised at a loud sound when
you change the source from the external component to another source.
DEMO OFF/ ON
You can change the initial indication on the display to information name
(function name, EQ name, etc...) while listen to a source.
BEEP 2ND / ALL
BEEP 2ND : The beep is generated when a key is long pressed. (1 sec)
BEEP ALL : The beep is generated when any key is pressed.
Using the EQ
EQ is to increase or decrease the signal strength of audio frequencies. The function helps you to enjoy sound more plentifully. Press XDSS/EQ repeatedly. The
indicator lights up in the following order.
POP t CLASSIC t ROCK t OFF(Not displayed.)
8
CAR CD/MP3/WMA Receiver
Checking the clock
You can see the clock pressing DISP.
Setting the clock
1 Press the DISP and then, press and hold DISP for more 1 second.
2 Press the < to adjust the hour.
3 Press the > to adjust the minute.
Listening to the radio
Connecting an Auxiliary Equipment
ON PLAYER
SRC
1. Select a source to tuner.
2. Select a band.
BAND
3. Auto seek.
Manual seek.
</>
< / > (Press and hold)
Auxiliary input
Listening to the radio - more you can do
MP3 Player, etc
ON PLAYER
Auto search memory
Press U/AS. The six strongest broadcast frequencies will be stored under preset
button 1-6 in the order of their signal strength.To cancel, press U/AS.
Storing and recalling broadcast frequencies
Line out
SRC
1. Select a source to AUX.
2. Play the connected Auxiliary Equipment.
3. Adjust the volume.
VOLUME + or -
1 Press BAND to select desired band you want to store.
2 Select the desired frequency and press one of preset buttons 1-6 and hold
until the beep sound.
3 Repeat steps 1-2 to preset other stations.The next time, you press the same
preset button, the radio station frequency is recalled from the memory.
To scan the preset stations
Press u/PS. Each preset station appears. To cancel, press u/PS.
To tune in the preset stations
Press BAND to select the desired band and press the desired preset button 16.
Note
• Up to 24 stations, 6 for each of three FM bands and 6 MW(AM) stations can
be stored in the memory.
• When a station is stored on the preset numbers on which another station of
the same band has already been preset, the previously preset station is automatically erased.
CAR CD/MP3/WMA Receiver
9
Listening a CD
ON PLAYER
1. Insert a CD.
2. Adjust the Volume.
VOLUME + or -
Note
During random playback, if you press < , you won’t go back to the previous
track.
MP3/WMA Track -10 / +10
(If there is no folder or one folder.) During playback press u/PS to go back 10
tracks, and press U/AS to go forward 10 tracks.
Listening a CD - more you can do
MP3/WMA Folder UP/DOWN
Pause or restart a CD
(If there are more than two folders.) During playback, press u/PS to go back to
the previous folder, and press U/AS to go forward to the next folder.
Press B[] on the player during playback. Press this button again to resume play.
Search for a section within a track / file
Press and hold < / > on the player for about 1 second during playback and then
release at the point you want.
Skip to another track / file
Press < / > on the player. If you want to skip to previous track or file, press briefly
< within 3 seconds of playing time.
Intro scan
Press or press and hold INT on the player. Each files in the current selected
folder (
INT) or the first 10 seconds of each tracks/files (INT) on the disc are
played. Press the INT again to cancel it.
Repeat
Press or press and hold RPT on the player. The current selected tracks/files (1
RPT) or folder (
RPT) on the disc is played repeatedly. Press RPT again to
cancel it.
Shuffle
Press or press and hold SHF on the player. Each files in the current selected
folder (
SHF) of all of the tracks/files (SHF) on the disc is played randomly.
Press SHF again to cancel it.
10
CAR CD/MP3/WMA Receiver
See information about your music
MP3/WMA files often come with tags. The tag gives the Title, Artist or Album.
Press DISP repeatedly during MP3/WMA/CD TEXT file playback. If there is no
information, “NO TEXT” will be shown in the display window.
Note
•
: The icon is displayed during MP3/WMA playback.
• MP3/WMA Disc compatibility with this unit is limited as follows:
1. Sampling Frequency / 8 - 48kHz (MP3) 22.05 - 48kHz (WMA)
2. Bit rate / within 8 - 320kbps (include VBR) (MP3) 32 -320kbps (WMA)
3. CD-R/CD-RW file system should be “ISO 9660”
4. If you record MP3/WMA files using software which cannot create a FILE
SYSTEM, for example “Direct-CD” etc., it will not be possible to playback
MP3/WMA files. We recommend that you use “Easy-CD Creator” which creates an ISO9660 file system.
5. WMA decoder is supported until “Class 2A”.
Customers should also note that permission is required in order to download MP3/WMA files and music from the Internet. Our company has no
right to grant such permission. Permission should always be sought from
the copyright owner.
Troubleshooting
Symptom
General
CD
Cause
Power doesn’t turn on / The Leads and connectors are not properly.
unit doesn’t operate.
The fuse is blown.
No sound is heard / The
volume level will not rise.
There’s audio skipping.
The playback is not possi
ble.
Noise and other factors are causing the builtin microprocessor to operate incorrectly.
Cables are not connected correctly.
This unit is not firmly secured.
The disc is dirty.
The loaded disc is of a type this unit cannot
play.
Correction
Confirm once more that all connections are
correct.
Rectify the problem that caused the fuse to
blow, and then replace it. Be very sure to
install the correct fuse with the same rate.
Turn the unit off and then on.
Connect the cables correctly.
Secure this unit firmly.
Clean disc.
Check what type the disc.
CAR CD/MP3/WMA Receiver
11
Specifications
General
Output Power
Power Source
Speaker impedance
Ground System
Dimensions (W x H x D)
Net Weight
Tuner
FM
Frequency Range
S/N Ratio
Distortion
Usable Sensitivity
AM (MW)
Frequency Range
S/N Ratio
Distortion
Usable Sensitivity
50W x 4CH (Max.)
DC 12V
4Ω
Negative
180 x 50 x 176 mm (Without Control Panel)
1.3 kg
87.5-107.9, 87.5-108, 65-74 or 87.5-108 MHz
55 dB
0.7%
12 dBµV
520-1720 or 522-1620 kHz
50 dB
1.0%
28 dBµV
CD
Frequency Response
S/N Ratio
Distortion
Channel Separation (1kHz)
20 Hz-20 kHz
80 dB
0.12%
55 dB
AUX
Frequency Response
S/N Ratio
Distortion
Channel Separation (1kHz)
Max Input Level (1kHz)
20 Hz-20 kHz
80 dB
0.12 %
45 dB
1.2V (35KΩ)
Designs and specifications are subject to change without notice.
P/N : MFL42688952
12
CAR CD/MP3/WMA Receiver
Download PDF

advertising