LG F1422TD Owner’s Manual

Add to my manuals
32 Pages

advertisement

LG F1422TD Owner’s Manual | Manualzz
Washing Machine
OWNER'S MANUAL
F1422TD(1~9)
F1222TD(1~9)
F1022TD(1~9) / WD-MD810
Thank you for buying a
LG Fully Automatic Washing machine.
Please read your owner's manual carefully, it provides
instructions on safe installation, use and maintenance.
Retain it for future reference.
Record the model and serial numbers of your washing
machine.
P
roduct Features
Protection against creases
With the alternate rotation of the drum, creasing in the laundry is
minimized.
Built-in Heater
Internal heater automatically heats the water to the best
temperature on selected cycles.
√fl∞°º±≈√ øπæ‡
C
More economical by Intelligent Wash System
Intelligent Wash System detects the amount of load and water
temperature, and then determines the optimum water level and
washing time to minimize energy and water consumption.
Child Lock
The Child lock prevents children from pressing any button to
change the settings during operation.
Low noise speed control system
By sensing the amount of load and balance, it evenly distributes
load to minimize the spinning noise level.
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
ontents
Warnings....................................................................................3
Specifications.............................................................................4
Installation..................................................................................5
Care before washing................................................................11
Adding detergent .....................................................................12
Function ...................................................................................14
How to use washer ..................................................................15
Maintenance ............................................................................22
Troubleshooting guide .............................................................26
Terms of Warranty ...................................................................29
2
W arnings
READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE
!
WARNING!
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following:
• Before installation, check exterior damages. If it has,
do not install.
• Do not install or store the washer where it will
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance instructions
or published user-repair instructions that you
understand and have the skills to carry out.
• Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags, chemicals, etc.
• Close supervision is necessary if this appliance is
used by or near children. Do not allow children to
play on, with, or inside this or any other appliance.
• Keep small animals away from the appliance.
• Do not leave the washer door open.
An open door could entice children to hang on the
door or crawl inside the washer.
• Never reach into washer while it is moving. Wait
until the drum has completely stopped.
• The laundry process can reduce the flame retardant
of fabrics.
• To avoid such a result, carefully follow the garment
manufacturer’s wash and care instructions.
• Do not wash or dry articles that have been cleaned
in, washed in, soaked in, or spotted with
combustible or explosive substances (such as wax,
oil, paint, gasoline, degreasers, dry-cleaning
solvents, kerosene, etc.) which may ignite or
explode. Oil may remain in the tub after a whole
cycle resulting in fire during drying. So, do not load
oiled clothes.
• Do not slam the washer door closed or try to force
the door open when locked. This could result in
damage to the washer.
• When the machine runs high temperature, the front
door may be very hot. Don’t touch it.
• To minimize the possibility of electric shock, unplug
this appliance from the power supply or disconnect
the washer at the household distribution panel by
removing the fuse or switching off the circuit breaker
before attempting any maintenance or cleaning.
• When unplugging power cord, do not pull out by
grasping the cord. Otherwise, the power cord may
be damaged.
• Never attempt to operate this appliance if it is
damaged, malfunctioning, partially disassembled, or
has missing or broken parts, including a damaged
cord or plug.
• Before discarding an old machine unplug it. Render
the plug useless. Cut off the cable directly behind
the appliance to prevent misuse.
• When a product was under water, Please call
service center. The risk of electric shock and fire.
❊ Do not push down the door excessively, when washer door open.
This could topple over the washer.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path
of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
• Do not use an adapter or otherwise defeat the grounding plug.
• If you don’t have the proper outlet, consult an electrician.
:
WARNING Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with
a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify
the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.
3
S
pecifications
■ Name
: Front loading washing machine
■ Power supply
: 220-240V~,50Hz
■ Size
: 600mm(W)
■ Weight/Max.Watt
: 61kg / 2100W
■ Wash capacity
: 8kg
■ Water consumption
: 56ℓ(7ℓ/ kg)
■ Permissible water pressure
: 100-1000kPa (1.0-10kgf/cm2)
■ Spin speed
: No Spin/400/800/1400 [F1422TD(1~9)]
No Spin/400/800/1200 [F1222TD(1~9)]
No Spin/400/800/1000 [F1022TD(1~9) / WD-MD810]
550mm(D) 850mm(H)
The appearance and specifications may be varied without notice to raise the units quality.
■ Accessories
Inlet hose(1EA)
4
Spanner
I
nstallation
Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other vermin,
pay particular attention to keeping the appliance and its surroundings in clean condition at all times.
Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance
guarantee.
Transit bolts
The appliance is fitted with transit bolts to prevent internal damage during transport.
• Packing and all transit bolts must be removed
before using the washer.
☞ When unpacking the base, be sure to remove the
additional packing support in the middle
of the base packing.
Washer
Base Packing
Removing transit bolts
1. To prevent internal damage during
transport, the special 4 bolts are
locked. Before operating the washer,
remove
the bolts along with the rubber bungs.
3. Take out the 4 bolts along with the
rubber bungs by slightly twisting the
bung. Keep the 4 bolts and the
spanner for future use.
• If they are not removed, it may cause
heavy vibration, noise and malfunction.
• Whenever the appliance is transported,
the transit bolts must be refitted.
2. Unscrew the 4 bolts with
the spanner supplied.
4. Close the holes with the caps supplied.
5
I
nstallation
Installation place requirement
Drain Hose
Washer
Laundry
Tub
approx.
2cm
Level floor :
Allowable slope under entire washer is 1˚
Power outlet :
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with more than one
appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear /2cm:right & left side)
Do not place or store laundry products on top of washer at
any times.
They can damage the finish or controls.
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets,rug etc.
• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar
materials under the washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning
stove,an insulating(85x60cm) covered with aluminum foil on the side facing the cooker or
stove,must be inserted between the two appliance.
• The washer must not be installed in rooms where the temperature can drop below 0°C.
• Please ensure that when the washer is installed, it is easily accessible for the engineer in
the event of a breakdown.
• With the washer installed adjust all four feet using the transit bolt spanner provided
ensuring the appliance is stable, and a clearance of approximately 20mm is left between
the top of the washer and the underside of the work-top.
BS Plug Safety Details (For U.K. User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This appliance must be earthed
Green and Yellow(Earth)
Brown(Live)
Blue(Neutral)
E
L
Fuse
N
Cord
grip
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E
or by the earth symbol
or coloured Green or Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red.
If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
6
I
nstallation
■ Electrical connection
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly
qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Place the washing
machine at room temperature for a few hours before putting it into operation.
CAUTION
This appliance is not intended for use by young children or infirm persons without supervision.
Young Children should be supervised to ensure that they do not play with appliance.
CAUTION
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
■ Washing Machine is to be connected to the water mains using new hose-sets and old hose-sets should
not be used.
■ Connecting water supply hose
▶Water supply pressure must be between 100kPa and 1000kPa
(1.0~10kgf/cm2)
▶Don’t strip or crossthread when connecting Inlet hose to the valve.
▶If the water supply pressure is more than 1000kPa, a decompression
device should be installed.
• Two rubber seals are supplied with the water inlet hoses. They are
used for preventing water leaks.
• Make sure the connection to taps is tight enough.
• Periodically check the condition of the hose and replace the hose if
necessary.
• Make sure that there is no kink on the hose and that it is not crushed.
NOTE
After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type
of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the
faucet into the adaptor.
7
nstallation
I
Normal Tap without thread & screw type inlet hose
1. Unscrew the fixing screw to
attach the tap.
2. Push the connector up till the
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.
3. Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
Normal Tap without thread & one touch type inlet hose (Single inlet models)
1. Untighten the upper connector
screw.
Upper
Connector
Fixing screw
Rubber
packing
Middle
connector
• In case the diameter of the tap is
large remove the guide plate.
Guide plate
2. Push the upper connector up till 3. Connect the water supply hose
the rubber packing is in tight
contact with the tap. Then
tighten the 4 screws.
Upper
Connector
Rubber packing
Plate
Upper
Connector
Water supply
hose
Middle
connector
• Turn the middle connector not
to have water leaked.
Connector
to the middle connector,
pushing the plate down.
• Make sure that the rubber seal
is inside the hose connector.
• To separate the water supply
hose from the middle connector
shut off the tap. Then pull the
inlet hose down, pushing the
plate down.
Hose connector
Rubber seal
Used the horizontal tap
Horizontal tap
Extension tap
Square tap
8
• Make sure that there are no
kinks in the hose and that it is
not crushed.
I
nstallation
Installation of drain hose
9
I
nstallation
Level adjustment
1. Adjusting the washing machine level properly prevents excessive
noise and vibration.
Install the appliance on a solid and level floor surface, preferably in a
corner of the room.
NOTE
Timber or suspended type flooring may contribute to
excessive vibration and unblance errors.
2. If the floor is uneven, adjust the adjustable feet as required. (do not
insert pieces of wood etc. under the feet)
Make sure that all four feet are stable and resting on the floor and
then check that the appliance is perfectly level. (use a spirit level)
※ After the washer is level, tighten the lock nuts up towards of the base of
the washer. All lock nuts must be tightened.
Adjustable
feet
NOTE
Adjustable
feet
In the case that the washing machine is installed on a raised
platform, it must be securely fastened in order
to eliminate the risk that it might fall off.
❊ Diagonal Check
When pushing down the edges of the washing machine top plate diagonally, the machine
should not move up and down at all. (Please, check both of two directions)
If machine rocks when pushing the machine top plate diagonally, adjust the feet again.
Concrete floors
• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.
Tile floors (Slippery floors)
• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm
sections and stick the pieces on to the dry tile where machine is to be placed.)
※ Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.
Wooden floors (Suspended floors)
Rubber Cup
• Wooden floors are particularly susceptible to vibration.
• To prevent vibration we recommend you place rubber cups under each foot,
at least 15mm thick under the washer, secured to at least 2 floor beams with screws.
• If possible install the washer in one of the corners of the room, where the floor is more stable.
※ Insert the rubber cups to reduce vibration.
※ You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept.
Important!
• Proper placement and levelling of the washer ensure long,regular and reliable operation.
• The washer must be absolutely horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.
10
C
are before washing
Before the first washing
Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash
without clothing. This will remove residues and water from the drum that may have been left
during manufacturing.
Caring before washing
1. Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and
how it should be washed.
2. Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can
occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly
soiled one.
Soil (Heavy, Normal, Light)
Separate clothes according to amount of soil.
Color (White, Lights, Darks)
Separate white fabrics from colored fabrics.
Lint (Lint producers, Collectors)
Wash lint producers and lint collectors
separately.
3. Caring before loading
Combine large and small items in a load. Load large items first. Large items should not be more than half
the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
• Check all pockets to make sure that they
are empty. Items such as nails, hair clip,
matches, pens, coins and keys can damage
both your washer and your clothes.
• Close zippers, hooks and strings to
make sure that these items don’t
snag on other clothes.
• Pre treat dirt and stains by brushing a little
detergent dissolved in water onto stains like
collars and cuffs to help shift dirt.
• Check the folds of the flexible gasket (gray) and
remove any small articles,if any.
• Check inside of the drum and remove any left
items in it for next wash cycle.
• Remove any clothing or items on the flexible
gasket to prevent clothing and the gasket
damages.
11
A dding detergent
Adding detergent and fabric softener
1. The Dispenser Drawer
• Main wash only ➔
MAX
• Pre Wash + Main Wash ➔
max
Detergent for
main wash
Fabric
softener
Detergent for
pre wash
2. Adding Fabric Softener
• Do not exceed the maximum fill line.
Close the dispenser drawer slowly.
Overfilling can cause early dispensing
of the fabric softener which could stain
clothes.
• Do not leave the fabric softener in the
detergent drawer for more than 2 days.
(Fabric softener could harden)
• Softener will automatically be added
during the last rinse cycle.
• Do not open the drawer when water is
supplied.
• Solvents(benzene, etc) are not
allowable.
NOTE
12
Do not pour fabric softener
directly on the cloths
A dding detergent
3. Detergent dosage
• The detergent should be used according to the
instruction of the detergent manufacture.
• If too much detergent is used, too many suds
can occur and this will decrease the washing
result or cause heavy load to the motor.
• Use powder detergent only for the front
loading washer.
❇ If suds occur too much, pleas reduce the
detergent amount.
• Detergent usage may need to be adjusted
for water temperature, water hardness,
size and soil level of the load. For best
results, avoid oversudsing.
❋ Tips
Full load : according to
manufacturer’s recommendation.
Part load : 3/4 of the normal
amount.
Minimum load : 1/2 of full load.
• Detergent is flushed from the dispenser
at the beginning of the cycle.
5. Using the Tablets
1) Open the door and Tablets into the
drum.
MAX
4. Water softener
max
2) Load the laundry into the drum.
• A water softener, such as Anti limescale
(Calgon) can be used to cut down on the
use of detergent in extremely hard water
areas. Dispense according to the amount
specified on the packaging.
First add detergent and then the water
softener.
3) Close the door.
• Use the quantity of detergent as for soft
water.
13
F
unction
Recommended courses according to the laundry type
Program
Fabric Type
Proper Temp.
Cotton
Color fast garments
(shirts, night dresses,
pajamas...)and lightly soiled white
cotton(underwear)
60˚C
(Cold, 30˚C,
40˚C, 95°C)
Synthetic
Polyamide, Acryic, Polyester
Cotton which is lightly soiled
40˚C
(Cold, 30˚C,
60˚C)
Quick 30
Colored Laundry which is lightly
soiled fast.
30˚C
(Cold, 40˚C)
Delicate
Delicate laundry easily damaged
(silk, curtains...)
Hand Wash /
Wool
Hand wash marked delicate and
machine wash wool laundry
Duvet
Cotton bedding with filling duvet,
pillow, blanket, sofa cover with
light filling
Bulky
Thick laundry absorbing much
water(Jumper)
Cotton Quick
Baby Care
Laundry for infant
Bio Care
For elimination of protein stains
Boiling Care
For elimination of remnant
detergent after boiling wash
Option
Maximum Load
Less than
8.0 kg
- Medic Rinse
- Intensive
- Pre Wash
- Crease Care
Less than
4.0 kg
Less than
8.0 kg
Less than
2.0 kg
Less than
2.0 kg
40˚C
(Cold, 30˚C)
- Intensive
- Crease Care
Less than
2.0 kg
1 Single size
30˚C
(Cold)
60˚C
(40˚C, 95°C) - Medic Rinse
- Intensive
60˚C
- Pre Wash
(95˚C)
- Crease Care
95˚C
Less than
8.0 kg
Less than
6.0 kg
Less than
8.0 kg
Less than
8.0 kg
❋ Water Temperature : Select the water temperature to the wash cycles.
Always follow garment manufacture’s care label or instructions when laundering.
❋ Medic Rinse : For high effectiveness or more purity in rinse operation you can choose Medic Rinse option.
❋ Pre Wash : If the laundry is heavily soiled, “Pre Wash” Course is recommended.
❋ Intensive : When washing heavily soiled laundry you can increase effectiveness by choosing “Intensive” option.
❋ Program setting with “Cotton 60˚C+Intensive” option for test in accordance or in conformity with EN60456 and
IEC60456.
❋ Crease Care : If you want to prevent crease, select Crease Care button.
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine
washable Woolmark products provided that the products are washed according to the instructions
on the garment label and those issued by the manufacturer of this washing machine M0806.
❋ Notes : Neutral detergent is recommended.
The wool cycle features gentle tumbling and low-speed spin for garment care.
14
H ow to use washer
1. Cotton automatically
selected upon power on.
• Press the Power button to start.
• Press the Start/Pause button.
• Initial conditions
- Wash : main wash
- Rinse : 3 times
- Spin :
2. Manual Selecting
• Press the Power button to start.
• Select the conditions which you want to use,
by turning the program dial and pressing
each button.
For selecting the each conditions, please refer to
the page16~page21
• Press the Start/Pause button.
3. Beep on/off
• 1400 rpm [F1422TD(1~9)]
• 1200 rpm [F1222TD(1~9)]
• 1000 rpm [F1022TD(1~9) / WD-MD810]
- Water temperature : 60˚C
- Program : Cotton
• The Beep on/off function can be set only
during the washing cycle.
• To set the Beep On/Off function follow the
below steps.
1. Turn on the washing machine (by pressing
the Power button).
2. Press the Start/Pause button.
3. Press and hold the Time Delay button
simultaneously for three seconds to set
Beep on/off function.
• Once the Beep on/off function is set, the
setting is memorized even after Power is off.
15
H ow to use washer
(1) Dial : Program
(2) Button : Start / Pause
(3) Button : Spin
(4) Button : Temperature
(5) Button : Power
(6) Button : Medic Rinse
(7) Button : Pre Wash
(8) Button : Intensive
Power
(9) Button : Crease Care
(10) Child Lock
(11) Tub Clean
(12) Button : Time Delay
Program
1. Power
• Press the Power button to turn power on and off.
• To cancel the Time Delay function, the power
button should be pressed.
2. Initial Program
• 13 programs are available according to the
laundry type.
• When the Power button is pressed, the
washer is ready for Cotton program. And the
other initial conditions as follows.
• So, if you want to advance into the ashing
cycle without changing the program, just
press the Start/Pause button and then the
washer will proceed.
■ Initial program
• [F1422TD(1~9)]
- Cotton Program / Main wash /
Normal Rinse / 1400 rpm / 60˚C
• Lamp will light up to indicate selected program.
• [F1222TD(1~9)]
- Cotton Program / Main wash /
Normal Rinse / 1200 rpm / 60˚C
Regarding to the laundry type for each program
Please refer to the page14.
• [F1022TD(1~9) / WD-MD810]
- Cotton Program / Main wash /
Normal Rinse / 1000 rpm / 60˚C
16
• When Start/Pause button is pressed, the
Cotton program is automatically selected.
- By turning the Program dial, the program is
selected in order of
“ Cotton – Cotton Quick – Synthetic – Duvet –
Bulky – Quick 30 – Rinse+Spin – Spin –
Delicate – Hand Wash/Wool – Bio Care –
Boiling Care – Baby Care”.
H ow to use washer
Start/Pause
Option
• By pressing the
Option button, all
Option functions
may be selected.
1. Start
• This Start/Pause button is used to start
wash cycle or pause the wash cycle.
2. Pause
1. Medic Rinse
• If temporary stop of wash cycle is
needed, press the Start/Pause button.
• For high effectiveness or more purity in rinse
operation you can choose Medic Rinse
option.
• When in Pause, the power is turned off
automatically after 4 minutes.
• NB. The door will not open before 1 to 2
minutes when Pause is selected,
or at the end of the wash cycle.
Detecting
• It can be chosen in all course with the
exception of Cotton Quick, Quick 30,
Hand Wash/Wool, Duvet, Delicate and Bulky.
2. Pre Wash
• If the laundry is heavily soiled, “Pre Wash”
course is effective.
• Pre Wash is available in Cotton, Cotton
Quick, Synthetic, Bio Care, Baby Care and
Boiling Care.
3. Intensive
• While the "Detecting" is shown in the display
the machine rotates slowly and detects how
many laundries are loaded in the drum. It will
take a few seconds.
• Available in Cotton, Cotton Quick and Synthetic.
Door Lock
• If the laundry is heavily soiled “Intensive”
option is effective.
• By selecting the Intensive option, the wash
time may be extended, depending on the
program selected.
4. Crease Care
• Lights whenever the door of the washer is
locked.
• The door can be unlocked by pressing the
Start/Pause button to stop the washer.
• The door can be opened after a short delay.
• If you want to prevent crease, select this
button with spin speed.
The required lamp will light up for identification.
17
H ow to use washer
Child Lock
If you choose to lock the buttons on the control
assembly to prevent tampering this function
may be selected.
• Child Lock can be set by pressing the Medic
Rinse button and Pre Wash button
simultaneously. (About three seconds)
• To deactivate Child Lock system, press
Medic Rinse and Pre Wash buttons
simultaneously again. (About three seconds)
• To change to the desired program, whilst in
child lock mode.
1. Press both Medic Rinse and Pre Wash
together once again. (About three seconds)
2. Press the Start/Pause button.
3. Select the desired program and press the
Start/Pause button again.
• The child lock can be set at any time and it
can be deactivated only by using child lock
cancel process. Turning the power off and
operational errors will not affect child lock.
18
Tub Clean
Tub Clean course can be set by pressing
and holding Intensive and Pre Wash button
simultaneously.
When Tub Clean course is set, display
“
”, and all buttons are inoperable.
TUB CLEAN is special cycle to clean the
inside of the washer. This cycle uses higher
water level with higher spin speed. Perform
this cycle regularly.
How to use the Tub Clean cycle:
1. Remove any clothing or items from the
washer and close the door.
2. Open the dispenser drawer and add Anti
limescale (Calgon) to the Main wash
compartment.
NOTE: Do not add any detergent to the
detergent compartments. Excessive
suds may generate and leak from the
washer.
3. Close the dispenser drawer slowly.
4. Power On and then press and hold
Intensive and Pre Wash button for 3 seconds.
then “
” is displayed in LED
5. Press the Start/Pause button to start.
6. After the cycle is complete, leave the door
open to dry around the washer door
opening, flexible gasket and door glass.
! CAUTION: If there is a small child, be
careful not to leave the door
open for too long.
H ow to use washer
Spin
• After selecting the spin course, the
spin speed can be chosen by
pressing the spin button.
[F1422TD(1~9)]
[F1222TD(1~9)]
[F1022TD(1~9) /
WD-MD810]
1. Spin selection
• Spin Speed is available according to
the program as follows.
F1422TD(1~9)
- Cotton, Cotton Quick, Rinse+Spin, Quick 30,
Bio Care, Bulky
Rinse Hold - No Spin - 400 - 800 - 1400
- Delicate, Duvet, Baby Care, Boiling Care,
Synthetic, Hand Wash/Wool
Rinse Hold - No Spin - 400 - 800
- Spin
No Spin - 400 - 800 - 1400
F1022TD(1~9) / WD-MD810
- Cotton, Cotton Quick, Rinse+Spin, Quick 30,
Bio Care, Bulky
Rinse Hold - No Spin - 400 - 800 - 1000
- Delicate, Duvet, Baby Care, Boiling Care,
Synthetic, Hand Wash/Wool
Rinse Hold - No Spin - 400 - 800
- Spin
No Spin - 400 - 800 - 1000
2. No spin
• If No spin is selected, the washer stops
after draining water.
F1222TD(1~9)
- Cotton, Cotton Quick, Rinse+Spin, Quick 30,
Bio Care, Bulky
Rinse Hold - No Spin - 400 - 800 - 1200
- Delicate, Duvet, Baby Care, Boiling Care,
Synthetic, Hand Wash/Wool
Rinse Hold - No Spin - 400 - 800
- Spin
No Spin - 400 - 800 - 1200
3. Rinse Hold
• Rinse Hold is selected by pressing the
spin button repeatedly this function
leaves clothes in the machine;
suspended in the water after a rinse
without entering into spin.
• To proceed through to a drain or spin,
once the rinse hold function is completed
using to Program dial and Spin button to
the required program.
(Spin)
The required lamp will light up for
identification.
19
H ow to use washer
Water Temp.
• By pressing the Temp.
button, the water
temperature can be
selected.
- Cold
- 30˚C / 40˚C / 60˚C / 95˚C
Time Delay
Preparing washing before starting
“Time Delay”
- Turn on the water tap.
- Load laundry and close the door.
• Water temperature can be selected
according to the program.
The required temperature lamp will light up
for identification.
For the more detailed information, please
refer to the page14.
- Place the detergent and fabric softener in
the drawer.
• How to set “Time Delay”
- Press Power button.
- Turn the Program dial to select
the program you require.
- Press Time Delay button and set the
desired time.
- Press the Start/Pause button.
(“:” blinks.)
• If Time Delay button is pressed, “3:00” is
displayed. The maximum delayed time is
19 hours and the minimum time is 3 hours.
• Each pressing of the button advances on
time delay by one hour.
• To cancel the time delay, press the Power
button.
• Time Delay is ‘expected time’ from the
present to the completion of washing cycle
or selected process (Wash, Rinse, Spin).
• According to the condition of water supply
and temperature, the delayed time and the
actual washing time may vary.
20
H ow to use washer
Display
3. Completion of washing
• When washing cycle is completed,
“
” is displayed on the “Multi
display”.
1. Special function display
4. Time left
• When child lock is selected, the
“
” is displayed.
• During washing cycle, the remaining washing
time is displayed.
• Recommended program by manufacturer.
• When time delay is selected, it shows
the remaining time to finish the selected
program.
2. Self diagnosis display
• If the machine encounters a fault during
operation, the associated fault will be
displayed.
“
“
“
“
“
“
“
“
“
“
” : Water pressure sensing error
” : Problem of overfilling water
” : Door is not closed
” : Over load in motor
” : Over load in motor
” : Water inlet trouble
” : Drainage trouble
” : Unbalanced load
” : Water temperature trouble
” : The washer experienced a
power failure.
If these error letters are displayed, please
refer to the troubleshooting page26 and
follow the guide.
- Cotton : around 1 hour and 52 minutes
- Cotton Quick : around 1 hour and 26 minutes
- Synthetic : around 1 hour and 15 minutes
- Quick 30 : around 30 minutes
- Hand Wash/Wool : around 51 minutes
- Delicate : around 57 minutes
- Duvet : around 1 hour and 9 minutes
- Bulky : around 59 minutes
- Baby Care : around 1 hour and 54 minutes
- Bio Care : around 2 hours and 14 minutes
- Boiling Care : around 2 hours and 17 minutes
- Rinse+ Spin : around 20 minutes
- Spin : around 15 minutes
• The washing time may vary by the amount of
laundry, water pressure, water temperature and
other washing conditions.
• If an unbalanced load is detected or if the suds
removing program operates, the wash time may
be extended.
(Max. increasing time is 45 minutes.)
21
M aintenance
❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical
shock to avoid electrical shock hazards.
❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable
the door lock to prevent young children being trapped inside.
The water inlet filter
-"
" error message will blink on the control panel when water does not enter the
detergent drawer.
- If water is very hard or contains traces of lime deposit, the water inlet filter may
become clogged.
It is therefore a good idea to clean it from time to time.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter using a hard bristle
brush.
4. Tighten up the inlet hose.
22
M aintenance
The drain pump filter
❋ The drain filter collects threads and small objects left in the laundry.
Check regularly that the filter is clean to ensure smooth running of your machine.
! CAUTION
First drain using the drain hose and then open the pump filter to
remove whatever any threads or objects.
Be careful when draining if the water is hot.
❋ Allow the water to cool down before cleaning the drain pump, carrying out
emergency emptying or opening the door in an emergency.
1. Open the lower cover cap. Drain plug
to pull out the hose.
001
1
2. Unplug the drain plug (②), allowing the
water to flow out. At this time use a vessel
to prevent water flowing on to the floor.
When water does not flow any more, turn
the pump filter (③) open to the left.
3
2
3. Remove out any foreign material from
the pump filter (③).
4. After cleaning, turn the pump filter (③)
clockwise and insert the drain plug (②)to
the original place. close the lower cover
cap.
3
2
23
M aintenance
■ Dispenser drawer
❋ After a while detergents and fabric softeners leave a deposit in the drawer.
• It should be cleaned from time to time with a jet of running water.
• If necessary it can be removed completely from the machine by pressing the catch
downwards and by pulling it out.
max
MAX
MAX
• To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
max
■ The drawer recess
❋ Detergent can also accumulate inside the recess which should
be cleaned occasionally with an old toothbrush.
• Once you have finished cleaning, replace the drawer and run a
rinse cycle without laundry.
■ The washing drum
• If you live in a hard water area, limescale may continuously build up in places where it cannot be
seen and thus not easily removed.
Over time the build up of scale clogs appliances, and if it is not kept in check these may have to
be replaced.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small
metal articles (paper clips, safety pins) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine
use.
❋ Descaler may contain chemicals that may damage part of your washing machine.
❋ Remove any spots with a stainless steel cleaning agent.
❋ Never use steel wool.
24
M aintenance
■ Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machine can be cleaned with warm water and a neutral non abrasive
household detergent.
Immediately wipe off any spills. Wipe with damp cloth.
Try not to hit surface with sharp objects.
❋ IMPORTANT: Do not use methylated spirits, diluents or similar products.
2. Interior
Dry around the washer door opening, flexible gasket and door glass.
Run washer through a complete cycle using hot water.
Repeat process if necessary.
NOTE
Remove hard water deposits using only cleaners labeled as washer safe.
■ Cold condition
If the washer is stored in an area where freezing may occur or moved in freezing
temperatures, follow these instructions to prevent damage to the washer:
1. Turn off water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into an empty wash drum.
Close the door.
5. Set spin cycle and let washer spin for 1minute to drain out all water.
Not all of the RV antifreeze will be expelled.
6. Unplug electrical power cord, dry the drum interior, and close the door.
7. Remove dispenser drawer drain and dry excessive water from the compartments.
8. Store washer in an uprignt position.
9. To remove antifreeze from washer after storage, run empty washer
through a complete cycle using detergent. Do not add wash load.
25
roubleshooting guide
T
❋ This washing machine is equipped with automatic safety functions which detect and diagnose faults at an
early stage and react appropriately
When the machine does not function properly or does not function at all, check the following points before
you contact your service provider.
Symptom
Possible Cause
Solution
Rattling and
clanking noise
• Foreign objects such as coins or
safety pins maybe in drum or
pump.
Stop washer and check drum
and drain filter.
If noise continues after washer
is restarted, call your authorised
service centre.
Thumping sound
• Heavy wash loads may produce
a thumping sound. This is usually
normal.
If sound continues, washer is
probably out of balance. Stop and
redistribute wash load.
Vibrating noise
• Have all the transit bolts and
packing been removed?
• Are all the feet resting firmly on
the ground?
If not removed during
installation. Refer to Installation guide
for removing transit bolts.
Wash load may be unevenly
distributed in drum. Stop washer and
rearrange wash load.
Water leaks.
• Fill hoses or drain hose are loose
at tap or washer.
Check and tighten hose connections.
• House drain pipes are clogged.
Unclog drain pipe. Contact plumber
if necessary.
Too much detergent or unsuitable
detergent may cause excessive
foaming which may result in water
leaks.
Oversudsing
Water does not enter
washer or it enters
slowly
Water in the washer
does not drain or
drains slowly.
26
• Water supply is not adequate in
area.
Check another tap in the house.
• Water supply tap is not
completely open.
Fully open tap.
• Water inlet hose(s) are kinked.
Straighten hose.
• The filter of the inlet hose(s)
clogged.
Check the filter of the inlet hose.
• Drain hose is kinked or clogged.
Clean and straighten the drain hose.
• The drain filter is clogged.
Clean the drain filter
T
roubleshooting guide
Symptom
Washer does not start
Possible Cause
• Electrical power cord may not
be plugged in or connection
may be loose.
Make sure plug fits tightly in wall
outlet.
• House fuse blown, circuit
breaker tripped,or a power
outage has occurred.
Reset circuit breaker or replace fuse.
Do not increase fuse capacity.
If problem is a circuit overload, have
it corrected by a qualified electrician.
Turn on water supply tap.
• Water supply tap is not turned
on.
Washer will not spin
Solution
❋ Check that the door is firmly
shut.
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the clothes
washer begins to spin. The door
must lock before spin can be
achieved.
Door does not open
Once started, the door can not be
opened for safety reasons.
Wait one or two minutes before
opening the door to give the electric
locking mechanism time to release.
Wash cycle time
delayed
The washing time may vary by the
amount of laundry, water
pressure, water temperature and
other usage conditions.
If the imbalance is detected or if the
suds removing program works, the
wash time shall be increased.
27
T
roubleshooting guide
Symptom
Possible Cause
Solution
• Water supply is not adequate in area.
• Water supply taps are not completely open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are clogged.
Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose.
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
• Load is too small.
• Load is out of balance.
• The appliance has an imbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, bath robe,
etc.) this system may stop spinning or even
interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning
• Is the door opened?
Close the door.
❋ If “
” is not released, call for
service.
Unplug the power plug and call for
service.
• Water overfills due to the faulty water valve. Close the water tap.
Unplug the power plug.
Call for service.
• Water level sensor has malfunctioned.
• Over load in motor.
• Over load in motor.
• The washer experienced a power failure.
28
Restart the cycle.
T
erms of Warranty
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a
product it means the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will help prevent
potential negative consequences for the environment and
human health.
4. For more detailed information about disposal of your old
appliance, please contact your city office, waste disposal
service or the shop where you purchased the product.
What Is Not Covered:
• Service trips to your home to teach you how to use the product.
• If the product is connected to any voltage other than that shown on the rating plate.
• If the fault is caused by accident, neglect, misuse or Act of God.
• If the fault is caused by factors other than normal domestic use or use in accordance
with the owner's manual.
• Provide instruction on use of product or change the set-up of the product.
• If the fault is caused by pests for example, rats or cockroaches etc..
• Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
• Correcting the installation for example, levelling the product, adjustment of drain.
• Normal maintenance which recommended by the owner's manual.
• Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
• Replace fuses in or correct house wiring or correct house plumbing.
• Correction of unauthorized repairs.
• Incidental or consequential damage to personal property caused by possible defects
with this appliance.
• If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training
center, dormitory)
If the product is installed outside the normal service area, any cost of
transportation involved in the repair of the product, or the replacement of a
defective part, shall be borne by the owner.
29
M emo
30
M emo
31
For U.K. Customer
P/No.: MFL49491538
CUSTOMER SERVICES Tel. : +44-(0) 844 847 LGLG(5454)
Fax.
: +44-(0) 844 847 1413
LGEUK SERVICE WEB-SITE : http://www.lge.co.uk

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Freestanding Front-load 8 kg 1200 RPM Silver
  • LED
  • Hygiene/anti-allergy, Black
  • Load balancing system Foam control system
  • Delayed start timer Remaining time indication Child lock
  • 56 L

Related manuals

Download PDF

advertisement