LG | LD-2161WH | LG LD-2161WH Owner’s Manual

3828DD3009H
2008.11.10 4:58 PM
˘
` 1
‰¯¿ł– •¡˙¨‰”
DISHWASHER
OWNER'S MANUAL
MODEL : LD-2160(1)W(S,M,L,T)H
LD-2160(1)W(S,M,L)HB
LD-2160(1)W(S,M,L,T)HU
Please read this manual carefully before operating your
dishwasher. Retain it for future reference.
3828DD3009H
2008.11.10 4:58 PM
˘
` 2
‰¯¿ł– •¡˙¨‰”
CONTENTS
SAFETY AND CAUTION
3
INSTALLATION INSTRUCTIONS
5
PARTS NAME
9
FUNCTION OF CONTROL BUTTON
10
HOW TO USE AND OPERATE
12
OPERATING SEQUENCE
18
PROGRAM
19
USER MAINTENANCE INSTRUCTIONS
20
TROUBLE SHOOTING GUIDE
21
SPECIFICATION
3828DD3009H
2008.11.10 4:58 PM
˘
` 3
‰¯¿ł– •¡˙¨‰”
SAFETY AND CAUTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING - When using your dishwasher, follow basic precautions,
including the following:
• Please read this manual carefully before
using the dishwasher for the first time.
• This manual contains very important notes
regarding the installation, use and
maintenance of your dishwasher.
• The manufacturer can not be responsible
for problems caused by ignoring these
safety and caution instructions.
• This dishwasher is designed for normal
household use.
• Do not use the dishwasher for industrial
and commercial use, or other purpose.
• The appliance is not intended for use by
young children or infirm persons without
supervision.
be placed in the dishwasher.
(Please avoid utensils; that are nonheatresistant, metal decorated, etc.)
• Do not use any kinds of solvent in your
dishwasher. They may cause an explosion
or fire.
• Do not spray water on the appliance.
It may cause the failure of electric parts or
electric shock.
• Do not push down or sit on the inner door
when the door opened. It may cause the
deformation or failure of your dishwasher.
• Do not use the detergent for hand
washing.
The detergent for dishwasher should be
used for normal operation.
• This appliance is fitted with a safety
function that automatically stops the
operation of the dishwasher when it is
exposed to heavy disturbance on its
mains.
• Dishwasher detergents are strongly
alkaline. They can be extremely
dangerous if swallowed. Avoid contact
with skin and eyes and keep children
away from the dishwasher when the door
is open.
Check that the detergent receptacle is
empty after completion of the wash cycle.
During installation
• Electrical connection must be in
accordance with the rating label.
• Electrical safety is only guaranteed when
the earth system of your house is in
accordance with the related local
regulations.(Do not use an extension cable
or cord.)
• If the hot water exceeds 65ºC, adjust the
water heater setting. If the hot water
temperature can not be maintained below
65ºC, the dishwasher must be connected
to cold water.
• If power supply cord is damaged, it must
only be replaced by the manufacturer or
its service agent or a similar qualified
person in order to avoid a hazard.
• This appliance must be positioned so that
the plug is accessible.
• The appliance is to be connected to the
water mains using new hose-sets and that
old hose-sets should not be reused.
Child Safety
• Controls may be locked using “Child
Lock” mode to prevent from all the setting
from being changed by a child.
• Keep children away from detergents and
rinse-aids.
• Do not allow children to operate the
dishwasher.
• Young children should be supervised to
ensure that they do not play with the
appliance.
During use
• Only suitable household utensils should
3
3828DD3009H
2008.11.10 4:58 PM
˘
` 4
‰¯¿ł– •¡˙¨‰”
SAFETY AND CAUTION
CAUTION
concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional outlets or branch circuits. Check the specification page
of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord
exits the appliance.
CAUTION
The instructions shall state the substance of the following :
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of least resistance for electric current.
This appliance is equipped with a cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service representative if you
are in doubt whether the appliance is properly grounded. Do not modify the plug
provided with the appliance; if it will not fit the outlet have a proper outlet installed
by a qualified electrician.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a
product it means the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will help prevent
potential negative consequences for the environment and human
health.
4. For more detailed information about disposal of your old
appliance, please contact your city office, waste disposal service
or the shop where you purchased the product.
4
3828DD3009H
2008.11.10 4:58 PM
˘
` 5
‰¯¿ł– •¡˙¨‰”
INSTALLING INSTRUCTIONS
Step 2 :
PREPARATION FOR ELECTICAL WIRING
WARNING
A qualified electrician/plumber or
competent person should carry out any
electrical/plumbing work required to
install this appliance.
CAUTION
For personal safety, remove house fuse
or open circuit breaker before installation.
Do not use an extension cord or adapter
plug with this appliance. Electrical and
earthing connections must comply with
the national electrical code/provincial and
municipal code and/or other local codes.
Step 1 :
PREPARE CUPBOARD OPENING
1 This dishwasher is designed to fit the size
shown as below.
2 Select a location as close to sink as
possible for ease of connection to the
water and drain pipes.
1 This appliance must be supplied with
correct rating voltage and hertz as shown
on instruction manual, and connected to
an individual, properly earthed branch
circuit, protected by a minimum 15 amp
circuit breaker or time delay fuse.
Wiring must be 2 wire with Earth.
3 To ensure good drainage, the dishwasher
should not be installed more than 3 meters
away from the sink.
4 If dishwasher is installed in a corner, a
minimum of 5cm of space is required
between the washer and an adjacent
cabinet or wall.
2 The power plug must be in a accessible
location adjacent to and not behind the
dishwasher and within 1.2 meters of the
dishwasher side.(See page 7 Fig.A)
3 The power plug must be correctly
earthed, if in doubt, have it checked by a
qualified Electrician. No other appliance
should be connected to the same plug
outlet by a double adapter or similar
plug.
Dangerous voltage
To indicate hazards arising from
dangerous voltages.
Note – In case of application in a
warning sign the rules according
to ISO 3864 shall be adhered to.
Unit:mm
Any bare wood surrounding the dishwasher
should be sealed with a waterproof paint or
sealant to prevent swelling.
5
3828DD3009H
2008.11.10 4:58 PM
˘
` 6
‰¯¿ł– •¡˙¨‰”
INSTALLATION INSTRUCTIONS
Step 3 :
PREPARING THE DISHWASHER
FOR INSTALLATION
Step 4 :
INSTALLING THE DISHWASHER
IN CUPBOARD
1 Lay the dishwasher on its back.
1 Before sliding the dishwasher into the
cupboard opening, all necessary height and
balancing adjustments should be made
using a spanner.
2 Adjust the legs to the required height
as shown in below figure.
2 Slide the dishwasher into the cabinet
opening carefully. Make sure that the
drain hose inside the cabinet is not
kinked or stretched.
CAUTION
If the height of the cupboard is below 850mm,
you should remove the top table by
unscrewing the 2 screws. (Two of rear)
6
3828DD3009H
2008.11.10 4:58 PM
˘
` 7
‰¯¿ł– •¡˙¨‰”
INSTALLATION INSTRUCTIONS
Step 5 :
DRAIN LINE CONNECTION
1 If the end of drain hose does not fit to
the drain line, use a rubber
connector(not supplied) that is
resistant to heat and detergent.
This should be available from a
plumbing shop or DIY merchants.
When the drain hose is connected to a
separate standpipe, it is essential that an
airtight connection be made.
Refer to Fig.B
2 There are two typical connections as
shown in Figure A, B.
The “S” trap spigot must be drilled out
cleanly and free of obstruction to its
maximum internal diameter, if used for
drainage.
To prevent siphoning, one of the following
methods must be used:
When the drain hose is connected to a
sink “s” trap or waste disposal unit, the
hose must be looped up to the underside
of the bench top and secured.
Fig. B : Drainage connection - stand pipe.
Drain hose Extension
Extend drain hose as shown below.
Fig. A
CAUTION
When you connect or extend drain hose,
make sure that drain hose is not kinked.
(Bends should have a 40 mm radius.)
7
3828DD3009H
2008.11.10 4:58 PM
˘
` 8
‰¯¿ł– •¡˙¨‰”
INSTALLATION INSTRUCTIONS
Step 6 :
WATER SUPPLY CONNECTION
Step 8 :
HOW TO LEVEL THE DISHWASHER
1 Connect the water supply hose to the
water tap as shown.(Some models consist
of an inlet valve and hose.)
This dishwasher may be fed with either
hot or cold water. If the water can not be
maintained below 65ºC, the dishwasher
must be connected to cold water.
After installing the dishwasher, you may notice
a slight sticking of the door to the dishwasher,
when you open or close the door. If this does
happen you need to adjust the level of the
dishwasher.
Case 1. In case the door is slanted to the right
2 When connecting, the sealant tape or
sealing compound to avoid water leaks.
Make sure that the line is not kinked or
sharply bent.
Fig. C
• If the door slants to the right, see fig, C and
follow these instructions:
1) Unscrew(counter-clockwise) the left leg of
the back side and correct the level.
2) Check the opening of door and repeat if
necessary until the door opens and closes
properly.
• When the product is correctly leveled, There
should be no slant , stickiness or friction sound.
Water tap
Water supply
hose
Case 2. In case the door is slanted to the left
Step 7 :
FINAL CHECK AND ASSEMBLING
1 Securely hand tighten supply hose to the
water supply.
Plug the power supply cord into an
earthed electrical point and switch on.
Fig. D
2 After installing and prior to using the
dishwasher with crockery, we
recommend that you use the dishwasher
on ‘Quick’ mode to rinse through. At this
stage it is useful to ensure that there are
no operating problems or water leaks.
When the dishwasher is used for the first,
there may be a loud noise, if this
happens, turn off the power and restart
the dishwasher.
• If the door slants to the left, see fig. D and
follow these instructions:
1) Check the opening of door if there still
remains sticky or friction sound.
2) Check the opening of door and repeat if
necessary until the door opens and closes
properly.
• When the product is correctly leveled, There
should be no slant , stickiness or friction
sound.
8
3828DD3009H
2008.11.10 4:58 PM
˘
` 9
‰¯¿ł– •¡˙¨‰”
PARTS NAME
10. Adjust Leg
11. Upper Rack
12. Cutlery Basket
13. Detergent And Rinse Aid Dispenser
14. Vapor Vent Cover
15. Upper Spray Arm
16. Lower Spray Arm
17. Filter ASM
18. Lower Rack
19. Salt Container Cap
1. Control Panel
2. Door Handle
3. Front Cover
4. Lower Cover
5. Process Monitor
6. Power Switch
7. Drain Hose
8. Inlet Hose
9. Power Cord
Funnel
The appearance and specifications may vary without notice.
9
3828DD3009H
2008.11.10 4:58 PM
˘
` 10
‰¯¿ł– •¡˙¨‰”
FUNCTION OF CONTROL BUTTON
TRIPLE SPRAY
RINSE
• With each press, the level
of water jet is changed to
Strong, Normal and Soft
in a sequence.
• Repeated pressing of the
Rinse button will select
Extra Hot, Rinse+.
• If you select the Extra
Hot function, the
operationg temperature
will be up to 80 .
(Intensive, Auto, Eco)
• When you select Rinse +
an additional rinse cycle is
added.
10
3828DD3009H
2008.11.10 4:58 PM
INDICATOR
• Refill with
special salt
• Refill with
rinse aid
˘
` 11
‰¯¿ł– •¡˙¨‰”
TIME LEFT
DELAY START
• Before starting, the display window shows the running time of
the selected program.
• After starting, the display window shows the remaining time.
• If the dishwasher has a trouble, the trouble type is displayed.
• If you want to delay the
start of selected program,
press this button before
pressing program button.
• Pressing the Delay Start
will increase time by 1
hour.
• The delay start time can be
adjusted from 1 hour to 19
hours.
• Child Lock
If this error letters are displayed, please refer to the trouble
shooting guide page 21 and follow the guide.
“ ” : No error message (See page 18)
PROGRAM
CHILD LOCK
BEEP ON/OFF
POWER
• When you want to
select program, press
each button.
• Used to lock or unlock the
control buttons to prevent
all the setting from being
changed by a child.
• This function is
automatically canceled
when power failure occur.
• For locking/ unlocking,
press Intensive and
Auto button for a few
seconds simultaneously.
• The dishwasher must be
switched on.
• The beep on/off function
can be set by pressing the
Intensive and Pre-wash
button simultaneously for
a few seconds. Then, a
“on” will appear in the
time display.
• The beep on/off function
is automatically canceled
when power failure occur.
• For operating, press this
button first for power on.
• After operating, this
button automatically
switches off for safety and
energy saving.
• In case of irregular surge
disturbance to the
machine, the power may
be automatically turned off
for safety.
11
3828DD3009H
2008.11.10 4:58 PM
˘
` 12
‰¯¿ł– •¡˙¨‰”
HOW TO USE AND OPERATE
Take care not to obstruct the rotation
of the spray arms and ensure that large
items do not prevent the detergent
dispenser lid from opening.
1. Loading your Dishwasher
For better washing performance, always load
the dishwasher according to the instructions.
Before loading items into the dishwasher
clean off large particles of food, in particular
insoluble items such as bones, pips, etc.
3. Using the Cutlery Basket
Cutlery should be mixed within each
section of the cutlery basket to prevent
nesting of similar items. Place the cutlery in
the cover with the handles down. The cover
can be hinged and clipped away from the
basket if you choose not to use them.
Place knives in the separate rack for located
in the top of the dishwasher.
When loading the dishwasher, please act
accordingly:
Position crockery such that water will
contact all surfaces.
Deep based items should be placed at an
angle to help water run off and dry
properly.
Items with burnt on food should be
soaked prior to loading in the dishwasher.
Take care when loading and unloading
sharp items.
2. Loading the Lower Rack
The lower basket is best loaded with dinner
plates, soup bowls, dishes, pots, pans, lids
and even the grill tray.
Plates should be positioned upright and
facing the centre of the rack and pots, pans
and large dishes must be turned upside
down.
WARNING
Knives and other utensils with sharp points
must be loaded in the basket with their
points down or placed in a horizontal
position.
12
3828DD3009H
2008.11.10 4:58 PM
˘
` 13
‰¯¿ł– •¡˙¨‰”
HOW TO USE AND OPERATE
4. Loading the Upper Rack
5. Adjusting the Upper Rack
It is best to load this with more delicate
items such as, small plates, long cutlery,
cups, glasses and dishwasher safe plastic
items. Plates should be positioned upwards
with the plate bottom facing the front of the
rack.
Cups, glasses and bowls must be positioned
upside down.
Extra cups or cooking utensils can be laid on
the fold down cup racks, which also provides
support for long stem glasses.
Take care not to obstruct the rotation of the
spray arm under the upper rack.
Your upper rack can be raised or lowered to
cater for different sized crockery. Before
adjusting, ensure that the rack is empty.
You can change the position of the upper
rack by lifting the rack upward, into the
upper position, or by pulling on the two
levers on either side of the rack to move it
down to its lower position.
We recommend that where possible the
upper rack remains level.
And when you pull the rack upward, hold
the middle location of the upper rack
(
marked position)
After adjusting the rack levels, check that
the spray arm is free to rotate.
Front
Non Dishwasher Safe Items
The combination of high water temperatures and
dishwasher detergent may damage particular
items, therefore we do not recommend using the
dishwasher to wash the following:
■ Copper or anodized aluminum
■ Hand painted silver or gold leaf crockery
■ Wood or bone handled utensils
■ Iron or non rust proof utensils
■ Plastic items that which are not dishwasher safe.
WARNING
Before adjusting, ensure the rack is
empty of all crockery.
Otherwise crockery may be damaged
or you may be injured.
13
3828DD3009H
2008.11.10 4:58 PM
˘
` 14
‰¯¿ł– •¡˙¨‰”
HOW TO USE AND OPERATE
6. Adding Detergent
Dispenser
Push latch to open
• Detergent must be put into the detergent
chamber before starting every program
except the Pre-Wash.
• Please follow the manufacturer’s instructions
within the manual, when determining the
correct amount of detergent to use.
• If your dishes are moderately dirty, you may
use slightly less detergent than
recommended.
• Chambers hold 15g and 25g.
• The amount of detergent required depends on
the program. Please refer to the guide table.
PROGRAM
AMOUNT OF DETERGENT
Intensive
25g
Auto
20g
Eco
15g
Quick
10g
Pre-wash
No detergent
Place proper
detergent into this
compartment
WARNING
The detergent used is a special
Dishwasher detergent and like all
household chemicals it should be
treated as harmful and kept out of reach
of children. After completion of the wash
program, the detergent compartment
should be checked and any remaining
detergent removed.
• After the detergent is supplied, the
chamber lid should be closed.
• The detergent is dispensed automatically
during the operation.
• The chamber lid remains open after
operation.
WARNING
# Attention : Using combined detergent
products(ex.3 in 1)
Some products integrated rinse aid work
best specific programs only.
You will obtain optimum rinsing and
drying results by using conventional and
separate salt and rinse aid.
Products that replace regeneration salt
can only be used within a specific water
hardness range.
Please contact the detergent
manufacturer if the drying performance
is very poor or you find the white film,
when you use the combined detergent
products.
We do not warrant the complaints that
are directly related to the use of these
products.
Detergent Information
Use only the detergent intended for
household dishwashers. (Ordinary handwashing detergent should not be used,
because the foam can interfere with proper
operation.)
14
3828DD3009H
2008.11.10 4:58 PM
˘
` 15
‰¯¿ł– •¡˙¨‰”
HOW TO USE AND OPERATE
7. Adding Rinse Aid
Dispenser
For filling
To fill the Rinse Aid chamber, rotate the
round cap counter clockwise and remove.
Fill the container to the maximum level
with a good quality Rinse Aid, then replace
and lock the cap.
The Rinse Aid is automatically dispensed
during the final rinse cycle.
The dosage is factory set to suit most
installations. If, after washing, you notice
cloudy spots, streaks or water marks on
your glassware, it may be necessary to
increase the setting. To do this, remove the
cap and rotate the indicator arrow to a
higher setting then replace the cap . If the
glasses are smeared or foam is present on
the bottom of the glass or the bottom of the
machine, select a lower setting.
For refilling
Depending on the dosage setting and the
number of washes, the chamber may need
to be topped up, approximately once a
month. The rinse aid level can be checked
by two methods.
• By the indicator window on the dispenser
when the dishwasher door is fully open.
● Black indicates sufficient Rinse Aid
O Clear indicates Rinse Aid required
• By the light on the control panel, being
lit, when the dishwasher is working on.
Rinse Aid Information
Rinse Aid is necessary to remove spots and
streaks from dishes as well as improved
drying. Using the correct amount will
improve wash performance. However, using
too much can produce excess foam leading
to possible water leaks.
When the lamp is lit, it means the rinse aid
is almost empty. Refill the Rinse Aid
chamber as soon as possible.
15
3828DD3009H
2008.11.10 4:58 PM
˘
` 16
‰¯¿ł– •¡˙¨‰”
HOW TO USE AND OPERATE
8. Salt Filling
This model has a water softener to soften hard water.
Please read these notes carefully for correct operation.
In order to provide satisfactory rinsing results, the dishwasher requires soft water, i.e.,containing little
or no lime, otherwise water stains will be left behind on the dishes and interior containers.
If the tap water exceeds a certain level of hardness, it must be softened, i.e.,decalcified.
This is achieved by adding a special salt to the water softener inside the dishwasher.
The required amount of salt is set up according to how hard your tap water is.
Filling with Salt for the first time
• Check the water hardness of your area. (Your water supplier will be able to tell you this.)
• Set the water hardness according to the setting method of the water softener.
• Remove lower rack and unscrew the cap of salt container.
• Before using your dishwasher for the first time, fill with salt, the container has a capacity of 1.9kg.
Use a funnel for ease and clean filling, ensuring that coarse salt or regenerating salt intended for
dishwashers is used.
• After filling, wipe off any spilled salt to seal the cap properly.
• Screw the cap tightly to prevent any suds from penetrating into the container.
Setting up the water softening system
Adjust the water softener to the setting to the corresponding hardness of the water in your area. The
water softener has 8 adjustment levels.
The dishwasher is programmed at the factory for a water hardness level of “
”.
This can be checked and altered by using the buttons on the control panel.
1. First, ensure the dishwasher is switched off.
2. Press Delay Start and Power button simultaneously and keep them pressed.
A “ ” and 1 figure will appear in the time display.
3. To change the setting:
Simply press the Quick button and the figure will change one by one.
The display will change between “
” and “
”.
4. Once the hardness setting is correctly adjusted, press the Pre-wash button.
The hardness setting is then saved.
16
3828DD3009H
2008.11.10 4:58 PM
˘
` 17
‰¯¿ł– •¡˙¨‰”
HOW TO USE AND OPERATE
For refilling
When the salt container is empty, the salt refill lamp will automatically turn on during operation.
The salt should be refilled after the cycle has finished. We recommended the salt refill should
always be carried out, as mentioned previous page, prior to starting the next operation. This will
immediately thin and drain away any excess salt solution.
When the lamp is lit, this means that the salt
aid is almost empty. Refill the Salt Aid
chamber as soon as possible.
Note
• After filling with salt, it may take a little while before the indicator light turns off.
• When the control is set to “ ”, it is not necessary to fill up with salt as no salt is consumed while the dishwasher is operating.
If the control is set between “ ” and “ ”, then salt must be added to the dispenser.
WARNING
Do not pour detergent into the salt container. This will destroy the water softener.
9. Fold down dividers.
10. Drying
■ Fold-down dividers at the lower rack can
be lowered to improve stacking of pots
and pans.
■ At the end of the program, it is
recommended to fully open the door to
assist in drying.
11. Energy Test(EN50242)
■ Appliance loaded in accordance with
standard specifications.
• Example of loaded dishwasher : p.12~13
• Capacity : 12 place settings
• Comparability course : Eco
• Rinse aid setting : 3
• Reference cleaner : 6g of detergent onto
the inside surface of the door and fill 24g
into the detergent dispenser.
• Height-adjustable Rack-U must be
inserted in the uppermost position.
17
3828DD3009H
2008.11.10 4:58 PM
˘
` 18
‰¯¿ł– •¡˙¨‰”
OPERATING SEQUENCE
After starting, the display window shows
the remaining time.
The time in the display window will start
to decrease minute by minute.
If the door is opened during the program a
safety device ensures that the machine
stops.
Once the door is re-closed the program
will start from where it was interrupted.
Press the “Power” button
Check there is rinse aid
and salt
The corresponding indicator lights will
illuminate if refilling is required.
Open the door and check
the filters
At the end of the washing
program
Ensure they are clean and properly
positioned (See “User Maintenance
Instructions”).
“
”is displayed on the digital display
and a buzzer sounds. The display then
shows “
” to indicate that the
dishwasher is in “Cool dry” mode.
Load the dishes
Remove any excess food.
Pull the lower rack out and arrange the
dishes and cutlery.
Pull the upper rack out and arrange the
cups, glasses, etc.
Cool dry-“Cd”
This process is not part of the program.
At the end of the program, the fan will
continue to operate for about an hour to
diminish any remaining moisture.
If you want, you can now open and unload
the dishwasher.
Otherwise the dishwasher automatically
switches off for safety and energy saving
later.
CAUTION
Do not load the items in upper rack with
the lower rack is pulled out and loaded.
Ensure the spray arms can
freely rotate
CAUTION
Empty the lower rack first and then the upper
one. This will avoid water dripping from the
upper rack onto the dishes below.
Measure out detergent
Add the required amount of detergent into
the dispenser and close the lid.
WARNING
In general it is not advisable to open the door
while the machine is working.
If the door is opened, a safety device
ensures that the machine stops.
Care must be taken if the door is opened
during the hot phase or immediately after a
program has finished, as steam may escape.
Setting and starting the
program
Press the program button to select the
desired program.
After 3 seconds, the machine will start.
If necessary, select the option function
corresponding to the desired program.
The indicator lights of the program and all
the phases of the program will come on.
Before starting, the display window shows
the running time of the selected program.
CAUTION
That the door should not be left in the open
position since this could present a tripping
hazard.
18
3828DD3009H
2008.11.10 4:58 PM
˘
` 19
‰¯¿ł– •¡˙¨‰”
PROGRAM
Running time may vary according to the water temperature, water pressure and voltage.
Running time doesn’t include “Cool dry - 60 min”.
Program
WASH
Pre Wash
50
Main
Wash
RINSE
Rinse 1
Rinse 2
Rinse 3
70
Heating
Rinse
DRY
Cool
dry
70
Intensive
Auto
The program sequence is optimized and adapted in accordance
with how dirty the dishes are.
45
65
35
40
Eco
Quick
Pre-wash
Intensive Wash
Eco Wash
This program offers the most efficient
energy and water consumption for a good
washing performance. It is recommended
that it will be used every time.
This program is ideal for very dirty
crockery, in particular pots, pans and
casserole dishes.
Auto Wash
During the Auto program, the degree of
soiling in the dishes is determined by the
amount of clouding of the water.
According the degree of soiling, the
program automatically adjust the washing
time, temperature. As a result, the energy
and water consumption is kept as low as
possible. The “F” on display means that
the sensor is sensing the status of the
dishwasher.
Quick Wash
Can use for lightly soiled recently used
dishes and cutlery.
Pre-wash
Can use this program for only removing
soil before washing dishes by hand.
“Cool dry” is not part of the operating program.(See page 18)
Auto Restart
If the dishwasher is turned off by a power failure, it will restart
automatically from the position it stopped at adjusting accordingly.
19
3828DD3009H
2008.11.10 4:58 PM
˘
` 20
‰¯¿ł– •¡˙¨‰”
USER MAINTENANCE INSTRUCTIONS
To prevent trouble and poor operating, it is important to check filters and spray
arms at regular intervals.
Filters
Upper Spray Arm
• Remove the lower rack first.
• Turn the mesh filter counterclockwise.
• Take out the mesh filter, upper STS filter
and outer filter.
• Clean them if necessary.
• Replace them in the reverse order.
• Pull the upper rack forwards.
• Check that the water jet holes are not
blocked.
• If cleaning is required, remove the arm by
unscrewing the nut.
• Clean the spray arm and replace it in the
reverse order.
mesh filter
upper STS filter
Upper spray arm
outer filter
Lower Spray Arm
• Check that the water jet holes are not
blocked.
• If cleaning is required, remove the arm by
pulling up.
• Clean the spray arm and replace it pulling
down.
20
3828DD3009H
2008.11.10 4:58 PM
˘
` 21
‰¯¿ł– •¡˙¨‰”
TROUBLE SHOOTING GUIDE
■ If a problem occurs check below to see whether this can be solved.
■ In the unlikely event that the problem cannot be rectified, please contact a
service engineer.
Possible Causes
Problem
No lights come on when the
power is turned on.
• Plug is not properly inserted into the socket.
• Fuse blown or circuit breaker tripped.
• The electricity of the house was cut off.
The machine does not start.
• Door is not fully closed.
• The start button is not pressed.
Water is not pumped away.
(The display show “ ” code.)
• The drain hose is kinked.
• The filter is clogged. (Clean the filter.)
The display shows “
(Automatically Drain Pump operated.)
• Excessive water is supplied than the normal water level.
• There is a problem with the inlet valve.
The display shows “
• Water is not supplied. (Water tap is not opened.)
The display shows “
The display shows “
” code.
” code.
” code.
” code.
• Water is leaking from the Hose connections.
• Damage to the unit has been caused by a water leak.
• The water heater circuit is damaged.
The spray arms do not rotate
smoothly.
• The mounting of the spray arms is blocked by food
particles. (Clean the holes of the spray arm.)
White deposits are left on the
dish washer after washing.
• The amount of detergent or rinse-aid set incorrectly.
• The salt container is empty.
• The salt container cap is not securely screwed on.
Streaks are left on glassware.
• Too little Rinse-Aid dispensed.
Dry results are not satisfactory.
• Too little Rinse-Aid dispensed.
Washing results are not
satisfactory.
• Incorrect amount of detergent.
• Utensils incorrectly arranged or overloaded.
• Filters are clogged.
• Water jet holes of spray arms blocked.
• Spray arms’ rotation obstructed by utensils.
• Unsuitable program selected.
The display shows “
”code.
• No error message.(See page 18.)
21
3828DD3009H
2008.11.10 4:58 PM
˘
` 22
‰¯¿ł– •¡˙¨‰”
MEMO
22
3828DD3009H
2008.11.10 4:58 PM
˘
` 23
‰¯¿ł– •¡˙¨‰”
MEMO
23
3828DD3009H
2008.11.10 4:58 PM
˘
` 1
‰¯¿ł– •¡˙¨‰”
LD-2160(1)W(S,M,L,T)H
LD-2160(1)W(S,M,L)HB
LD-2160(1)W(S,M,L,T)HU
P/No.: 3828DD3009H
Capacity
12 Place settings
Weight
See rating label
Power Supply
See rating label
Power Consumption
See rating label
Water Feed Pressure
50 ~ 800 kPa
Download PDF

advertising