LG | WD-1055FB | LG WD-1055FB Owner’s Manual

WD-6550FB/WD-8050F(H)B
WD-1050F(H)B/WD-1055F(H)B
WD-1253F(H)B/WD-1255F(H)B
P
roduct Feature
Jumbo drum
40%
LG's
drum
jumbo
can
wash about 40%
conventional
washing
performance.
wash
More economical
Intelligent
Wash
machines. A
more
bigger
load than
drum
the
by Intelligent Wash System
System
detects the amount of load and water
temperature, and then determines the optimum
washing
improves
time to minimize energy and water
water level and
consumption.
Child-Lock
Temp.
The Child-Lock
Eco/Rapid
pressing
system has been used
any button to
Low noise
change
to
prevent children from
the program
during operation.
speed control system
the amount of load and balance, it
load to minimize the spinning noise level.
By sensing
evenly
distributes
Auto Restart
If the
washing machine is
automatically from
restart
turned off
the
by a power failure, it will
position it stopped at adjusting
accordingly.
C
ontents
Warnings....................................................................................3
Specification
..............................................................................4
Installation..................................................................................5
Care before
washing................................................................11
Adding detergent
.....................................................................12
Function ...................................................................................13
How to
use
washer ..................................................................14
Maintenance ............................................................................21
Troubleshooting guide
2
.............................................................24
W arnings
READ ALL INSTRUCTIONS BEFORE USE
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
WARNING!
!
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock,
the
?
Do not install
be
?
?
or
store the washer where it will
?
the weather.
exposed to
Do not
tamper with controls.
repair or replace any part of the washer
attempt any servicing unless specifically
instructions
published user-repair
or
instructions
?
that you understand and have the skills to carry
Keep the area underneath and around your
appliances free of combustible materials such
lint, paper, rags, chemicals, etc.
Close supervision is necessary if this
is used
by
or near
Do not wash
dry
or
articles that have been
or spotted with
explosive substances (such as
wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may
ignite or explode.
To avoid such a result, carefully follow the
garment manufacturer's wash and care
in, washed in, soaked in,
or
on,
with,
this or any
Do not leave the washer door open.
An open door could entice children to
or
appliance
or
?
inside
?
Never reach into washer while it is
?
The
hang
can
try to
To minimize the
this
possibility of electric shock,
appliance from the power supply
or
disconnect the washer at the household
on
?
moving.
completely stopped.
laundry process
retardant of fabrics.
or
distribution
crawl inside the washer.
until the drum has
Do not slam the washer door closed
force the door open when locked. This could
result in damage to the washer.
as
unplug
play
other appliance.
the door
?
children.
Do not allow children to
?
using
instructions.
out.
?
to persons when
combustible
recommended in the user-maintenance
?
injury
cleaned
Do not
or
or
washer, follow basic precautions, including the following:
Wait
reduce the flame
panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This
grounded. In the event of malfunction or breakdown, grounding will reduce the risk
by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
Do not use an adapter or otherwise defeat the grounding plug.
appliance
must be
of electric shock
?
?
If you don't have the proper
WARNING :
outlet, consult
an
electrician.
Improper
connection of the equipment-grounding conductor can result in risk of electric
qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
shock. Check with
a
-
3
S pecification
Power
If the
plug
supply cord is damaged,
replaced by the
it must be
manufacturer
or its service agents
similarly qualified person in
Drawer
or a
(For detergent and
fabric softener)
order to avoid
Control
a
hazard.
panel
Drain hose
Door
Lower
cover
Drum
Adjustable
Drain pump filter
Lower
Drain
cover
cap
plug
Name
Power
supply
:
Front
:
220-240V~,50Hz
600mm(W)
63kg
loading washing
Size
:
Weight
Wash capacity
:
:
Refer to the
Max. Watt
:
2100W
Spin speed
:
Water
consumption
Permissible water pressure
The appearance and
machine
600mm(D)
Rating
850mm(H)
Label.
400/500/650[WD-6550FB]
400/600/800[WD-8050F(H)B]
400/600/800/1000[WD-1050(5)F(H)B]
400/600/800/1000/1200[WD-1253(5)F(H)B]
:67
(9.6 /kg)
: 0.3-10kgf/
(30-1000kPa)
specifications
may be varied without notice to raise the units
Accessories
Inlet
4
feet
hose(1EA)
Option
:
Hot/Cold(2EA)
Spanner
quality.
nstallation
I
or store where it will not be exposed to temperatures below freezing or exposed to the weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
Install
Transit bolts
The
appliance
is fitted with transit bolts to
Removing
prevent internal damage during transport.
transit bolts
1. To
prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts
along
with the rubber
3. Take out the 4 bolts
along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future
?
?
If
they
are
not
removed, it may
use.
bungs.
cause
heavy
Whenever the
appliance
is
transported,
the
transit bolts must be refitted.
vibration, noise and malfunction.
cap
2. Unscrew the 4 bolts with
the spanner
4. Close the holes with the caps
supplied.
supplied.
5
nstallation
I
Installation
place requirement
Level floor
Drain Hose
Allowable
Washer
:
under entire washer is 1˚
slope
Power outlet
:
Must be within 1.5 meters of either side of location
of washer. Do not overload the outlet with
than
Laundry
one
Additional Clearance :
For wall, door and floor modeling is
Tub
approx.
2cm
more
appliance.
(10cm
: rear
Do not
place
/2cm:right
or
store
& left
required.
side)
laundry products
washer at any times.
They can damage the finish
or
on
top of
controls.
650
850
600
BS
Plug Safety
Details (For U.K. User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This
appliance
Green and Yellow(Earth)
must be earthed
E
Brown(Live)
L
Blue(Neutral)
Fuse
N
Cord
grip
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the
identifying
letter E
or
by
the earth
symbol (
)
or
coloured Green
or
Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N
or
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L
If
a
13 amp
6
(BS 1363) plug
is
used, fit
a
13 amp BS 1362 fuse.
coloured Black.
or
coloured Red.
nstallation
I
Electrical connection
1. Do not
use an extension cord or double adapter.
supply cord is damaged, it must be replaced by the
or similarly qualified person in order to avoid a hazard.
Always unplug the machine and turn off the water supply
2. If the
3.
4. Connect the machine to
5. The
appliance
Washing
must be
an
manufacturer
after
so
that the
plug
is
easily
its service
agents
use.
earthed socket in accordance with current
positioned
or
wiring regulations.
accessible.
Machine is to be connected to the water mains using
new
hose-
sets and that old hose-sets should not be used.
Connecting
water
supply hose
Water
supply pressure must be between
(0.3~10kg.f/cm2)
30kPa and 1000kPa
Don't
strip or crossthread when connecting
Inlet hose to the valve.
If the water supply pressure is more than
1000kPa, a decompression device should be
installed.
?
Two rubber seals
are
supplied with
the
water inlet hoses these are in order to
prevent
?
Hose connector
Rubber seal
water leaks.
Check water tightness of washing
machine connections by turning the
completely
?
tap
on.
Periodically check the condition of the
replace the hose if necessary.
hose and
?
Hose connector
Make sure that there is no kink
hose and that it is not crushed.
on
the
Rubber seal
When your washer has two valve,
Hot water
tap
?
Cold
Cold
Hot(option)
water
tap
?
The Inlet hose which has red connector is
for the hot water tap.
If the washer has two valves, the energy
is saved by using hot valve.
7
nstallation
I
Normal Tap without thread &
1. Unscrew the fixing
attach the tap.
screw
to
2.
screw
type inlet hose
Push the connector up till the
rubber
packing
with the
3.
is in
tap. Then
tight contact
tighten the 4
screws.
Normal Tap without thread &
1. Untighten the upper
connector
2.
touch type inlet hose
one
Push the upper connector up till
the rubber
screw.
packing
contact with the
Upper
Rubber
Connector
Fixing
tighten
packing
screw
Middle
the 4
Rubber
connector
Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
is in
3.
Connect the water
to the middle
tight
tap. Then
pushing
the
supply
hose
connector,
plate
down.
screws.
Upper
Connector
packing
Plate
Upper
?
In
case
large
the diameter of the
remove
Guide
the
tap is
Connector
Water
hose
Middle
guide plate.
connector
plate
Turn the middle connector not
?
to have water leaked.
Connector
?
Make
sure
that the rubber seal
is inside the hose connector.
?
To
supply
separate the
water
supply
hose from the middle connector
shut off the
inlet hose
plate
tap. Then pull the
down, pushing the
down.
Hose connector
Rubber seal
Used the horizontal
Horizontal
tap
tap
?
Your machine
comes
with
only
cold water connection.
?
Extension
tap
Make
sure
that there
not crushed.
Square tap
8
are no
kinks in the hose and that it is
I
nstallation
Installation of drain hose
ca.
ca.
145
100
cm
cm
?
max.10cm min.60cm
ca.
105
When
installing the drain hose sink,
it tightly with a string.
secure
cm
?
Proper securing the drain hose will protect
damage due to water
leakage.
the floor from
Laundry tub
ca.
100
cm
Hose
ca.
145
Retainer
cm
Tie
max.
ca.
?
than 100
Proper securing
protect
water
?
cm
placed
?
above the floor.
the drain hose will
the floor from
damage
due to
leakage.
When the drain hose is too
100cm
min. 60cm
strap
min. 60cm
min.60cm max.10cm
cm
The drain hose should not be
higher
?
105
100cm
max.
When
installing the drain hose sink,
it tightly with a string.
secure
?
Proper securing the drain hose will protect
damage due to water
leakage.
the floor from
long, please
don't fill into the washer. This will
cause
abnormal noise.
9
I
nstallation
Level
adjustment
1.
Leveling
a
the
washing
machine
properly
prevents excessive noise and vibration.
Install the
floor
the
appliance
on a
solid and level
surface, preferably in
a corner
of
room.
2. If the floor is uneven, adjust the
adjustable feet as required. (do not insert
pieces
Make
of wood etc. under the
sure
and
that all four feet
that the
adjustable
Higher
adjustable
stable
the floor and then check
resting
appliance
a spirit level)
on
feet)
are
is
perfectly
level.
(use
feet
Lower
feet
Diagonal Check
When pushing down the edges of the
washing machine top plate diagonally,
machine should not
move
the
up and down at
(Please, check both of two directions)
If machine rocks when pushing the machine
top plate diagonally, adjust the feet again.
all.
10
C
before
are
washing
Caring before washing
1. Care Labels
Look for
garment
2.
label on your clothes. This will tell you about the fabric content of your
and how it should be washed.
a care
Sorting
To
get the best results, Sort clothes into loads that can be washed with the same wash cycle.
temperature and spin speed and different fabrics need to be washed in different ways.
Water
Always
transfer
sort dark colors from
soiled items with
Soil
3.
pale
colors and whites. Wash
discoloration of white etc. If
causing
lightly soiled
can occur
separately as dye and lint
possible, do not wash heavily
one.
(Heavy, Normal, Light)
(White, Lights, Darks)
(Lint producers, Collectors)
Color
Separate
Separate
Lint
Wash lint
clothes
according
to amount of soil.
white fabrics from colored fabrics.
and lint collectors
producers
separately.
Caring before loading
Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
?
Check all the
that
as
pockets
to make sure
empty. Things such
nails, hair clip, matches, pens,
they
are
coins and
keys
can
damage
both
your washer and your clothes.
?
Close
zippers,
make
sure
snag
?
on
hook and
little
to
other clothes.
Pre treat dirt and stains
a
strings
that these items don't
detergent
by brushing
dissolved in water
onto stains like collars and cuffs to
help
shift dirt.
11
A dding detergent
Adding detergent
1. The
and fabric softener
3. Detergent
Dispenser Drawer
?
The
dosage
detergent should be used according to
of the detergent manufacture.
the
instruction
max
?
If too
much
detergent is
used more than the
recommended amount, too many suds can
occur and this will decrease the washing result
heavy load to the
malfunction)
or cause
?
Use powder
loading
?
Main wash
only
U
?
(Causing
a
detergent only for the front
washer.
Detergent
for water
?PreWash+MainWashU
motor.
usage may need to be
temperature,
water
adjusted
hardness,
size and soil level of the load. For best
2.
results, avoid oversudsing.
Adding Fabric Softener
(
)
MAX
MAX
125 ml
125ml
Tips
Full load
Part load
?
Do not exceed the maximum fill line.
Overfilling
can cause
clothes.
Do not leave the fabric softener in the
Softener will
during
?
automatically
cycle.
2
days.
be added
last rinse
Do not open the drawer when water is
supplied.
?
Solvents(benzene, etc)
are
not
allowable.
NOTE
Do not pour fabric softener
directly
12
on
:
3/4 of the normal amount.
Minimum load
?
:
1/2 of full load.
Detergent is flushed from the dispenser
beginning of the cycle.
the
detergent drawer for more than
(Fabric softener could harden)
?
to
early dispensing
of the fabric softener which could stain
?
according
:
manufacturer's recommendation.
the cloths
at
F
unction
Recommended
courses
Fabric
laundry type
Washing
Proper
Temp.
(Option)
Program
Type
Coloreds
to the
according
Maximum
Time
Washing
in
(Option)
Load
Minutes
(Cold, 60˚C)
Main(+Pre)
Rating
106
95˚C
Main(+Pre)
Rating
140
Color fast garments
40˚C
(shirts, night dresses,
pajamas...)and lightly
soiled white cotton
(underwear...)
Whites
First check if
laundry is
machine washable.
(white cotton, linen
towels and sheets...)
Synthetic
Delicate
Wool
Polyamide, Acrylic,
Polyester
laundry easily
damaged
(silk, curtains...)
Cold
:
For
heavily
Temperature
:
Cold
new
soiled and
protein-stained
Select the water
garment
care
kg
kg
Less than
2.0
kg
106
69
46
items.
temperature
manufacture's
4.0
3.0
Main
(40˚C)
Less than
Less than
Main
(40˚C)
Machine washable
Pre Wash
Main(+Pre)
(Cold, 60˚C)
Delicate
woolens with pure
wool only
Water
40˚C
to the wash
label
or
cycles. Always
follow
instructions when
laundering.
13
H
(
ow
to
washer
use
) : WD-6550FB/WD-8050F(H)B
Coloreds
no
inlet
imbalance
no
Time Left
Super
Pre
Main
drain
40
Hold
Door
Lock
400
30
600
800
1000 1200
Synthetic
Delicate
Wool
Eco
95
60
Normal
Whites
Rapid
Child Lock
Cold
Programme
Wash
Rinse
Spin
Time
Delay Temp. Eco/Rapid
(Temp.)
1. For
use
in the initial
?
?
Start /Pause
(Rapid)
2. Manual
To start press the Power button.
Press the Start/Pause button.
?
?
Initial condition
-
Wash
:
Main wash
-
Rinse
:
3 times
-
-
Spin : 800(650) rpm
Water temperature
:
Program : Coloreds
14
To start press the Power button.
Select the conditions which you want to
use, by pressing each button.
For selecting the each conditions, please
refer to the page15~page20
?
-
Selecting
(Coloreds)
programme
?
(Eco)
40˚C
Press the Start/Pause button.
to
ow
H
(
washer
use
) : WD-6550FB/WD-8050F(H)B
Whites
Coloreds
no
no
Time Left
Super
Pre
inlet
imbalance
Main
drain
60
400
Lock
Child Lock
30
600
800
1000 1200
Wool
Rapid
40
Hold
Door
Delicate
Eco
95
Normal
Synthetic
Cold
Programme
Wash
Rinse
Spin
Time
Delay Temp. Eco/Rapid
(Temp.)
(1)
(1)
(2)
(3)
(4)
Button
:
Wash
Button
:
Rinse
Button
:
Spin
Button
:
Time
(2)
(3)
(4)
(Eco)
Start /Pause
(Rapid)
(5) (6) (7)
(8)
(9)
(5) Button : Temp.(Eco)
(6) Child lock
(7) Button : Eco/Rapid(Rapid)
(8) Button : Programme
Delay(Temp.)
Wash
?
Pre
By pressing
can
(9) Button : Start/Pause
(10) Button : Power
Rinse
the Wash
?
Time Left
Super
button, the wash type
Main
(10)
button, the
Rinse type can be
Hold
-
selected.
Main Wash
-
Wash
-
Pre
+
Main Wash
-
Rinse
-
-
1. Main Wash
?
Main Wash
course
is available for
lightly
normally soiled laundry.
2. Pre
?
If the
+
Main Wash"
?
is
course
Normal
Super
Normal
+
Hold
Super + Hold
1. Normal
?
heavily soiled,
Coloreds / Whites / Synthetic / Delicate
performs 3 Rinses
"Pre
?
+
Wool performs 2 Rinses
is effective.
Pre Wash is available in
and
or
Main Wash
laundry
the
Rinse
Normal
be selected.
By pressing
Coloreds,
Whites
2.
Super
Synthetic program.
?
If lamp
turns on,
selected.
that function has been
?
Normal
+
1
more
rinse time.
Use the Super rinse when additional
rinsing is desired to remove excess dirt
and detergent soiled loads.
15
to
ow
H
use
washer
3. Rinse Hold
?
1.
If you desire to leave fabrics in the
machine without spinning after rinse to
prevent them from getting wrinkled, you
may select rinse hold
Rinse button.
by pressing
the
?
hold
according
Coloreds / Whites /
Synthetic
800U 1000U 1200U 400U 600
-
Delicate / Wool
400U 600
lamp.
If lamp
rpm is available
as follows.
WD-1253(5)F(H)B
To drain and
or
Spin
program
-
spin, press the Rinse button
Start/Pause button to turn off the rinse
Spin selection
turns on,
WD-1050(5)F(H)B
that function has been
selected.
-
Coloreds / Whites /
Synthetic
800U 1000U 400U 600
-
Spin
Delicate / Wool
400U 600
Time Left
Time Left
WD-8050F(H)B
-
Coloreds / Whites /
Synthetic
800U 400U 600
400
400
600
800
600
1000 1200
800
1000
-
Delicate / Wool
400U 600
Spin
Spin
WD-6550FB
-
Fuzzy Logic & Quiet
Fuzzy Logic & Quiet
-
400
600
800
400
Spin
?
By pushing
can
the
Spin button,
the
spin
rpm
be chosen.
[WD-1050(5)F(H)B]
400
-
400
600
-
600
-
800
-
800
-
1000
-
1000
-
1200
-
650
Spin
[WD-1253(5)F(H)B]
-
500
[WD-8050F(H)B]
[WD-6550FB]
-
400
-
400
-
600
-
500
-
800
-
650
16
Coloreds / Whites /
650U 400U 500
Delicate / Wool
400U 500
Synthetic
to the
to
ow
H
use
Time
washer
Water
Delay
Temp.
?
Time Left
Super
95
Time Left
Time Left
Super
60
Normal
Normal
40
Hold
Hold
30
water
-
1. Water
Delay
?
Preparing washing before starting
Turn on the water tap.
"Time Delay"
-
-
-
Load
laundry and close the door.
detergent and fabric softener
Place the
95˚C
-
-
-
-
Delay"
-
Press the Power button.
Turn the
Programme
dial to select
-
the program you require.
Press the Time Delay button and set the
Press the Start/Pause button.
(":" blinks.)
If Time
Delay button is pressed, "3:00" is
displayed. The maximum delayed time is
-
19:00 hours and the minimum time is 3:00
Each
pressing of the
delay by one hour.
To cancel the time
button advances time
delay,
?
Time
press the Power
'expected time' from the
present to the completion of washing cycle
selected process (Wash, Rinse, Spin).
Delay
According to
as
Synthetic
60˚C
U
U
Cold
U
30˚C
Whites
95˚C
Delicate & Wool
U 30˚C U 40˚C
Coloreds &
Synthetic
60˚C
U
U
Cold
Whites
Delicate & Wool
U 40˚C
Selected
is
the condition
be selected
Cold
button.
?
can
to the program.
95˚C
-
?
Coloreds &
40˚C
hours.
?
according
WD-1050(5)F(H)B /
WD-8050F(H)B / WD-6550FB
-
?
temperature
below
Cold
desired time.
-
Water
40˚C
How to set "Time
Temperature
WD-1253(5)F(H)B
in the
drawer.
?
Cold
-30˚C/40˚C/60˚C/
Time De
Temp.
1. Time
temperature
be selected.
can
Cold
Time De
By pressing the
Temp button, the
temperature's lamp
For the
more
refer to
the page13.
detailed
turns
on.
information, please
or
of water supply and
temperature, the delayed time and the actual
washing time
may vary.
17
H
ow
to
use
washer
Child lock
Change the
desired
Tem
E
program
o/Rapid
Start /Pause
Temp.
?
Eco/Rapid
If you want to lock all the buttons to prevent
operation by a child or infirm persons, this
function
WD-6550FB/WD-8050F(H)B
1. Child lock
?
Child lock
The child lock can be set at any time and it
is automatically canceled when operational
errors occur. Also Child lock works when
power is off.
be used.
can
?
Child lock
can
be set
holding the Eco
simultaneously.
by pressing and
holding
Temp.
Eco/Rapid
button simultaneously.
can
be set
the
Start /Pause
button and
by pressing and
Rapid button
button and
Child Lock
Eco
Rapid
Child Lock
E
Tem
o/Rapid
?
When child lock is set, all buttons
are
inoperable.
?
When child lock is set, all buttons
are
?
inoperable.
?
To deactivate Child lock
hold Eco and
To deactivate Child lock
system, press and
hold Temp. and Eco/Rapid
simultaneously again.
Rapid
system, press and
button
simultaneously
again.
button
Child Lock
Eco
Rapid
Child Lock
Tem
?
E
o/Rapid
?
If you want to change the program when
Child lock is active,
1. Press both
Temp.
and
Eco/Rapid
If you want to change the program when
Child lock is active,
1. Press both Eco and
Rapid together.
2. Press the Start/Pause button.
3.
together.
Change the desired program and press
the Start/Pause button.
2. Press the Start/Pause button.
3.
Change the desired program and press
the Start/Pause button.
Change the
desired
program
Eco
Rapid
Start /Pause
?
18
Start /Pause
The child lock can be set at any time and it
is automatically canceled when operational
errors occur. Also Child lock works when
power is off.
to
ow
H
use
washer
Start/Pause
Eco/Rapid
(
) : WD-6550FB/WD-8050F(H)B
?
Eco
button in White
program, Eco function
is selected. Eco
function gives you
almost the same
washing effect as that
in 95 C with less
Rapid
Child Lock
Temp.
(Eco)
If you press the
Eco/Rapid(Rapid)
Eco/Rapid
(Rapid)
consumption.
If you press the Eco/Rapid(Rapid) button
in Coloreds or Synthetic program, Rapid
function is selected. Rapid function reduces
the whole time including the washing and
rinsing time about by half an hour.
Start /Pause
1. Start
?
cycle
or
?
If
5 programs
are
available
laundry type.
-
-
-
-
-
Coloreds
press the "Start/Pause" button.
?
After the pause button is pressed, the
power is turned off automatically 4 minutes
later.
Power
according
Whites
Synthetic
to the
Delicate
Wool
Coloreds
Whites
Synthetic
1. Power
Delicate
Programme
Wool
?
(Programme)
Program
When Start/Pause button is
By turning
the
pressed,
automatically selected.
Program dial,
the program is
U Whites
Synthetic
U
to the
Regarding
Please refer to
Delicate
U
?
?
the page13.
Program
When the Power button is
pressed,
the
So, if you
want to advance into the
washing cycle without selecting the
program, just press the Start/Pause
button and then the washer will proceed.
-
Coloreds
-
-
Whites
-
Synthetic
it
ready for Coloreds program.
And the other initial conditions as follows.
2. Course
-
Delay function,
washer is
Wool".
laundry type for each program
on
also be used.
2. Initial
selected in orders of "Coloreds
U
To cancel the Time
can
Coloreds program is
-
Press the Power button to turn power
and off
?
1.
?
cycles.
temporary stop of wash cycle is needed,
Programme
?
pause the
2. Pause
energy
?
This Start/Pause button is used to start
wash
Delicate
Wool
Initial program
-
Coloreds Program / Main wash /
Normal Rinse/800(650) rpm / 40˚C
19
ow
H
to
use
washer
3. Time left
Display
WD-1050(5)F(H)B/WD-1253(5)F(H)B
Time Left
Super
?
95
60
Normal
During washing cycle, the remaining
washing time is displayed.
Recommended program
?
Hold
30
-
Cold
400
600
800
1000 1200
-
-
1. Self
diagnose display
-
-
?
If the washer has
a
"
"
"
"
"
"
"
"
"
"
"
"
"
If this
to the
?
:
Sensing
:
Problem of
:
Door is not closed
:
Over load in motor
:
Over load in motor
water pressure error
overfilling
?
:
Water temperature trouble
:
Motor is not
operating
error letters are displayed, please refer
troubleshooting page24 and follow the
Completion of washing
When
washing cycle is completed,
is displayed on the "Multi
display".
"
20
"
:
around 1 hour and 46 minutes
Whites
:
around 2 hours and 20 minutes
Synthetic
:
around 1 hour and 46 minutes
Delicate
:
around 1 hour and 9 minutes
Wool
:
around 46 minutes
The
washing time may vary by the
laundry, water pressure,
water temperature and other washing
amount of
water
guide.
2.
Coloreds
trouble, the trouble
type is displayed.
"
by
manufacturer.
40
conditions.
?
If the imbalance is detected
suds
or
if the
removing program works, the
wash time shall be
(Max. increasing
longer.
45minutes.)
time is
aintenance
M
Before
cleaning
the washer interior,
the electrical power cord to avoid electrical
unplug
shock to avoid electrical shock hazards.
The water inlet filter
-
"no inlet"
error
detergent
-
message will blink
the control
on
when water does not enter the
panel
drawer.
If your water is very hard
or
contains traces of lime
deposit,
the water inlet filter may
become
It
clogged.
is therefore a good
idea to clean it from time to time.
2. Unscrew the
1. Turn off the
water
water inlet
tap.
hose.
3. Clean the
filter
4.
using
Tighten
up
the inlet
a
hard bristle
hose.
brush.
The drain pump filter
The drain filter collects threads and small
Check
!
regularly
CAUTION
that the filter is clean to
First drain it
using
1.
Open the lower cover
cap( )byusing
2.
laundry.
running of your machine.
plug(
water
use a
flowing
remove
it up.
if the water is hot.
Unplug the drain plug ( ),
allowing the water to flow out.
this time
the hose.
stopped
draining
coin. Turn the drain
)topullout
left in the
smooth
the drain hose and then open the pump filter to
whatever may have
Be careful when
objects
ensure
vessel to
on
3. Take out any
At
prevent
to the floor. If the
foreign material
( ). After
turn
the
cleaning,
pump filter ( )
from the pump filter
clockwise and insert the drain
water does not flow any more, turn
plug ( )to the original place.
the pump filter
close the lower
( )
open to the left.
cover
cap.
100
3
1
3
2
2
21
aintenance
M
Dispenser drawer
After
a
while
detergents
and fabric softeners leave
a
deposit
?
It should be cleaned from time to time with
a
?
If necessary it
from the machine
can
be removed
completely
water.
by pressing
the catch
downward and
?
by pulling it out.
cleaning, the upper part
jet of running
in the drawer.
To facilitate
of the fabric softener
compartment
can
be removed.
max
max
The drawer
Detergent
can
recess
also accumulate inside the
should be cleaned
?
rinse
cycle
without
The
washing
If you live in
a
and it is not
easily
cleaning, replace
laundry.
the drawer and
run
drum
hard water area, limescale
continuously
builds up in
places where
clogs appliances,
and if it is not
kept
in check these will
Although the washing drum is made of Stainless steel, specks of rust
articles (paper clips, safety pins) which have been left in the drum.
?
The
washing
If you
use
can
be caused
descaling agents, dyes
or
bleaches, make
Descaler could contain
components that
Remove the
a
22
eventually
use
by
small metal
drum should be cleaned from time to time.
sure
they
are
suitable for
washing
use.
Never
seen
replaced.
?
?
it cannot be
removed.
Over time the build up of scale
have to be
which
old toothbrush.
Once you have finished
a
?
with
recess
an
occasionally
spots
with
steel wool.
stainless steel
can
attack
part of your washing machine.
cleaning agent.
machine
aintenance
M
Cleaning
your washer
1. Exterior
of your washer
can
extend its life.
The outside of the machine
can
be cleaned with
Proper
care
household
water and a neutral non abrasive
detergent.
Immediately wipe
Try
warm
off any
not to hit surface with
IMPORTANT: Do not
spills. Wipe
with
damp
cloth.
sharp objects.
methylated spirit,
use
diluents
or
similar
products.
2. Interior
Dry around the washer door opening, flexible gasket
always be clean to ensure a water tight seal.
Run washer
through
a
complete cycle using
Repeat
process if necessary.
NOTE
Remove hard water
Winterizing
winterizing
1. Turn off water
an area
4. Add
where
instructions to
areas
should
labeled
as
washer safe.
freezing
can occur or
prevent damage
moved in
freezing temperatures,
to the washer:
supply tap.
electrical cord into
Plug
These
hot water.
deposits using only cleaners
2. Disconnect hoses from water
3.
glass.
instructions
If the washer is stored in
follow these
and door
1gallon(3.8L)
a
supply
and drain water from hoses.
properly grounded
nontoxic recreational
electrical outlet.
vehicle(RV)
antifreeze to
empty wash drum. Close
door.
5. Set
spin cycle
and let washer
spin
Not all of the RV antifreeze will be
6.
Unplug
electrical power
7. Remove
Replace
dispenser
remove
through
a
expelled.
cord, dry drum interior, and close door.
drawer. Drain any water in
compartments and dry compartments.
drawer.
8. Store washer in
9. To
for 1minute to drain out all water.
an
uprignt position.
antifreeze from washer after
storage,
complete cycle using detergent.
run
empty washer
Do not add wash load.
23
T roubleshooting guide
This
washing machine is equipped with automatic safety functions which detect and diagnose faults at an
early stage and react appropriately
When the machine does not function properly or does not function at all, check the following points before
you call the Service Department.
Possible Cause
Symptom
Rattling and
clanking noise
?
Solution
Foreign objects such as coins
safety pins maybe in drum or
or
Stop
washer and check drum
and drain filter.
If noise continues after washer
pump.
is restarted, call your authorized
service.
Thumping
Vibrating
sound
noise
?
?
a
Heavy wash loads may produce
thumping sound. This is usually
probably
normal.
redistribute wash load.
Have all the transit bolts and
packing
?
If not removed
been removed?
Are all the feet
the
resting firmly
If sound continues, washer is
out of balance. Stop and
during
installation. See Installation for
on
removing
transit bolts.
Wash load
ground?
in drum.
unevenly distributed
Stop washer and
rearrange wash load.
Water leaks.
?
Fill hose connection is loose at
tap
?
or
Check and
tighten
hose connections.
washer.
House drain
pipes
are
clogged.
Unclog
drain
pipe.
Contact
plumber
if necessary.
Too much
Oversudsing
detergent?
can cause
Water does not enter
washer
or
?
it enters
slowly
Water
supply
it not
adequate
in
detergent
or
unsuitable
The formation of foam
water leaks.
Check another
tap in the house.
area.
?
Water
?
Water inlet hose
?
The filter of the inlet hose
supply tap
completely open.
is not
are
Fully
kinked.
open tap.
Straighten
hose.
Check the filter of the inlet hose.
clogged.
Water in the washer
does not drain
drains
24
slowly.
?
Drain hose is kinked
?
The drain filter is
or
clogged.
Clean and
straighten
or
clogged.
Clean the drain filter.
the drain hose.
T roubleshooting guide
Possible Cause
Symptom
Washer does not start
?
Electrical power cord may not
plugged in or connection
be
Solution
Make
plug
sure
fits
tightly
in wall
outlet.
may be loose.
?
House fuse blown, circuit
Reset circuit breaker
breaker
Do not increase fuse
tripped,or
a
power
outage has occurred.
If
problem
is
a
replace
capacity.
or
fuse.
circuit overload, have
it corrected
?
Water
supply tap
is not turned
by a qualified electrician.
on water supply tap.
Turn
on.
Washer won't
spin
Check that the door is
shut.
firmly
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the clothes
washer
begins to spin. The door
spin can be
must lock before
achieved.
Door does not open
Once started, the door can not be
for safety reasons.
opened
Wait
one or
two minutes before
opening the door to give the electric
locking mechanism time to release.
Wash
cycle
delayed
time
The
washing time may vary by the
laundry, water
amount of
pressure, water temperature and
other using conditions.
If the imbalance is detected
suds
or
if the
program works, the
wash time shall be increased.
removing
25
T roubleshooting guide
Possible Cause
Symptom
no
no
inlet
drain
?
Water
?
Water
supply it not adequate in area
supply taps are not completely
?
Water inlet hose
?
The filter of the inlet hose
are
Solution
Check another tap in the house.
open.
kinked.
Fully open tap.
Straighten hose.
Check the filter of the inlet hose.
clogged.
Clean and
straighten
?
Drain hose is kinked
?
The drain filter is
?
Load is too small.
Add 1
?
Load is out of balance.
balance the load.
?
The
Rearrange
spinning
appliance
clogged.
clogged.
has
or
an
imbalance detection
and correction
system. If individual heavy
articles are loaded bath mat, both robe, etc.
this system may stop spinning or even
imbalance
interrupt the spin cycle altogether,
imbalance is too
spin
?
great
even
the drain hose.
Clean the drain filter.
or
2 similar items to
help
load to allow proper
if the
after several
starts.
If the
laundry is still too wet at the end of
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
the
?
Is the door
opened?
Close the door.
If"
Door
"is not released, call for service.
Lock
(WD-6550FB/
WD-8050F(H)B)
Unplug the
service.
95
60
Fuzzy Logic &
40
Quiet
Cold
(WD-6550FB/
WD-8050F(H)B)
26
power
plug
and call for
T roubleshooting guide
Possible Cause
Symptom
?
If the water overfills due to the
Solution
faulty water
valve, you will get
"
"
?"
"
Pre
Close the water tap.
Unplug the power
Call for service.
display.
plug.
Main
(WD-6550FB/
WD-8050F(H)B)
is
displayed
if the water level
sensor
malfunction.
Super
Normal
Fuzzy Logic &
Hold
Quiet
(WD-6550FB/
WD-8050F(H)B)
Fuzzy Logic &
400
?
Over load in motor.
?
Over load in motor.
?
Motor is not
Quiet
600
800
(WD-6550FB/
WD-8050F(H)B)
95
60
40
Fuzzy Logic & Quiet
Cold
400
600
800
(WD-6550FB/
WD-8050F(H)B)
operating.
Super
Normal
Hold
Fuzzy Logic & Quiet
400
600
800
(WD-6550FB/
WD-8050F(H)B)
27
P/No.: 3828ER3007G
Download PDF

advertising