LG | WP-860QP | LG WP-860QP Owner’s Manual

LG Electronics
P/No.: 3828EY3002B
Machine
Washing
OWNER'S MANUAL
MODEL
:
WP-850QP/WP-850GP/WP-850NP
WP-860QP/WP-860GP/WP-860NP
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back
cover
and
quote this
information to your dealer when you require service.
This washing machine is designed and manufactured for
household
use
only.
CONTENTS
SAFETY MEASURE
3~4
PARTS IDENTIFICATION
4~5
INSTALLATION
6~7
PREPARATIONS BEFORE WASHING
8
HOW TO WASH
9
HOW TO RINSE
10~11
HOW TO SPIN
11
AFTER FINISHING
12
REFERENCE
12
CARE AND MAINTENANCE
13~14
TROUBLESHOOTING GUIDE
14
SPECIFICATIONS
15
2
SAFETY MEASURE
?
Manufacturer is not responsible for accidents caused
of not following the user's guide.
by
the
user as a
result
CAUTION
In
?
Installation Area
Operation
Do not insert the hand inside
the spin dryer basket while
the machine is in operation
(Do not let children climb
on the machine or
climb into the tub
?
Avoid area exposed to snow, rain,
or where humidity is high.
It may cause electric
shock.
Injury may occur.)
Switch Area
?
Avoid watering
switch area
It may cause
electric shock
or fire.
Spin
on
the
?
Volatile Material
?
Do not
Motor
After continuous using spinning
program 3 times, please stop
spinning more than 1 hour.
Otherwise the spin motor could be
damaged of fired.
Heat
volatile material such
as Benzene, Gasoline, bug killer.
Do not leave strong alkaline
substance such as bleach inside
the tub. Damage on
plastic surface and
rubber parts may
use
?
Avoid electric heater, candle
cigarette light, bug smoker,
light,
etc. near the machine.
It may ignite
deform
or
plastic part.
occur.
Hard
Electric Outlet
?
?
Avoid connecting several electric
devices to single outlet. It may
cause fire.
Power Cord
?
If the power supply cord is
damaged, it must only be replaced
by the manufacture or its service
agent or a similarly qualified
person in order to avoid
a
hazard.
3
objects
Remove pins, buckles and
removable hard objects in the
wash load to avoid damaging the
tub before your washing
CAUTION
Hot water
?
Installation
Avoid using hot water
over 50°C. It may
deform plastic parts
or cause malfunction.
Install the washing machine
horizontal support.
?
on
a
Otherwise,
it may cause
vibration and
noise.
Power Cord
?
Do not treat the power
supply cord with
your wet hand.
out the power supply
cleaning or not
Plug
?
When
cord,
the washing
machine for
a long time.
using
PARTS IDENTIFICATION
1
2
0
3
OFF
15
4
NORMAL
3
STRONG
GENTLE
OFF
N'
WATER SELECTOR
129
DO
6
0
WASH-RINSE
ROTATE
T
WASH
5
OFF
5
1
DRAIN
2
4
3
WASH TIMER
WASH SELECTOR
DRAIN SELECTOR
SPIN TIMER
6
1. Water
Supply
5. Drain Selector
Inlet
Connect here with the inlet hose from the
Select "WASH-RINSE" for
water faucet to feed water to the tub.
rinsing
Select "WASH" to
and
supply water for
rinsing and "SPIN" for spin
pump
6.
shower rinse.
3.Wash Timer
max.
washing
or
4. Wash Selector
Set the selector to "GENTLE", "NORMAL",
"STRONG" according to kinds and
of the
Timer
laundry.
4
spinning.
The
limit is 5 min. Don't rotate the knob
prescribed limit.
Buzzer(Option : Inside)
It is electrically operated to facilitate you
know the completion of washing cycle.
more
rinsing.
quantity
Spin
Select the desired time for
Select the desired time for
and
of the tub, and "OFF" to turn off the drain
2. Water Selector
washing
washing
and "DRAIN" to drain the water out
than
to
PARTS IDENTIFICATION
DRAIN HOSE
WASHING
SPIN DRYER
COVER
COVER
SUPPLY SELECTOR
SAFETY
LEVER
COVER-2
OVER FLOW
SPIN DRYER
FILTER
BASKET
ROTATION
FILTER-C
EARTH WIRE
(For models with
two prong plug)
TUB
SAFETY
COVER-1
PULSATOR
(Vertical movement of smaller
plate can be operated only when
sufficient amount of laundry is
deposited.
only for WP-850QP, WP-860QP, WP-850GP, WP-860GP)
POWER CORD
Accessories
OPTION
Safety
Cover
OPTION
Drain Hose Asm
Wheel Asm ×4
Wheel Shaft
×
4
Adjustable Leg
5
×2
INSTALLATION
Installation
?
?
Select flat and firm floor.
Incorrect installation may cause
severe noise and break down.
Leveling
?
?
area
the machine
?
Maintain more than 10cm between
the side of drain hose and the wall.
(Option)
Lift the front of the washing machine and twist the Adjustable
Leg until the washing machine is placed evenly.
If the Adjustable Leg is too short, use the Level Adjusting
Plates as shown.
Connecting
?
the drain hose
Connect the drain hose to the
outlet of the
plunger
?
valve located
at the back side of the
washing
Push the clamp toward the body
of the washing machine as shown
in the figure.
machine.
Voltage Change (only for dual voltage)
This washer is assembled for 220V, but can be changed from 220V to 110V(or 127V).
Check your electrical source and follow the diagram below to convert voltage.
6
Connecting
?
the earth wire
Install the earth wire to prevent short-circuit
leaking current and electric shock.
Gas
due to
?
?
pipe
It is attached at the back of the washer.
Connect it to the metal water pipe. If the water
Earth
wire
pipe is made of plastic, it does not have the
earth effect.
Never connect the earth wire to the gas pipe, lightning arrester.
telephone
connecter, etc.
WARNING-THE APPLIANCE WITH TWO-PRONGED PLUG MUST BE GROUNDED.
Other
?
earthing
After
method
connecting
the
?
earth wire to the earth
Connect to the
only
earthing-
outlet.
When
installing it in an
earthing is
possible, purchase
area
copper plate, bury it at
least 75cm deep under
the wet
?
not
where
a
short-circuit breaker
ground.
(15mA
at
7.5mA at
operation,
idle) and
connect it to the outlet.
Earth
wire
Short-circuit breaker
Earth
wire
75cm
Earth copper
plate
Connecting
?
?
?
?
the power
plug
Insert the power
plug into the outlet.
connecting the power plug, check if the voltage
setting of the washer matches the outlet voltage.
If AC outlet with ground terminal is used, grounding is
not needed. If not, never forget earthing (earthing
method above).
The appliance must be positioned so that the plug is accessible.
Before
7
Ground terminal
PREPARATIONS BEFORE WASHING
Preparation
Connect the water
to the water
supply
hose
Inlet hose
inlet.
supply
Connect the
power cord to the
electrical outlet.
Set the
supply
selector
lever to "WASH" for
washing
and
rinsing,
to "SPIN" for interim
spin
Less than 1m
rinse.
Note: The water selector
lever should not be
placed near the center
(as shown in Fig
Drain hose
Hang up the
drain hose.
otherwise water flows
to the wash and
tub
spin
simultaneously.)
(Fig
Before
)
washing
Remove any objects
Check the washing
123
from the pockets of the
instructions labels
on
be
the clothing
washing
to
clothing. Object left in
pockets may
damage the clothing or
washing machine
(especially cause
clogging of the drain
hose).
the
$
8
After
separating
or dyed
laundry, wash.
oiled
an
1Set
the drain selector to
"OFF"
OFF
position.
0 WASH
2
Set the water selector to
3 Open
the water
tap and
fill water in the wash tub
about halfway to the
"WASH"
desired water level.
RINCE
WASH
WATER SELECTOR
DRAIN SELECTOR
Put the
4
appropriate
detergent and
laundry into the wash
amount of
the
5
Select the wash selector
to
"GENTLE", "NORMAL",
Set the desired wash
6
time.
"STRONG"
tub. And add water to the
desired water level.
according to
quantity of
laundry
kinds and
the
0OFF
15
3
12
6
NORMAL
STRO
GENTLE
NG
WASH TIMER
Refer to TABLE 2 in
REFERENCE on page 12
WASH SELECTOR
for information
Refer to TABLE 2 in REFERENCE
on
page 12.
When
Refer to TABLE 2 in
to select the
REFERENCE
washing
is
page 12
Put the
and drain
the
on
how
appropriate
time.
8 Spinning laundryspin dryer
to
position
on
in the
finished,
7 select washing
the drain selector
"DRAIN"
9
basket.
into
spin dryer basket.
laundry down lightly.
Place the safety cover horizontally
on the laundry.
the water out.
Put the
OFF
0
Set the desired
spin time with
the spin timer.
DRAIN SELECTOR
9
HOW TO RINSE
Interim
?
Interim
spin
laundry
and
1
spin
rinse
rinse
prior to regular rinsing
improve rinsing efficiency.
After washing.
Put the laundry into the
spin dryer basket.
Place the safety cover
horizontally on the
2
?
will
remove
Set the water
sudsy
34
selector to "SPIN"
?
water from the
Allow the water to
flow appropriately.
laundry.
Turn off the water supply,
close the safety cover-2
and spin dryer cover
SPIN
WATER SELECTOR
Set the desired
time
spin
56
with the spin timer
Economical water
?
This
course
appropriate
1
allows you to
RINSE"
position
appropriate
and feed
?
rinse
supply
water as this course is to rinse after
feeding
water to the tub.
Set the drain selector to
"WASH
save
After spinning.
Put the laundry
into the wash tub
and rinse.
Set the rinse time with
2 the wash timer
Put the
laundry
into the
3 spin dryer basket and
set the
the
water to the tub.
0OFF
spin time
spin timer.
with
0OFF
OFF
0
15
3
5
6
4
1
WASH
WATER SELECTOR
12
DRAIN SELECTOR
4
Put the
laundry
WASH TIMER
into the wash tub and
9
repeat
10
2
3
1 to 3
course.
SPIN TIMER
Continuous water
?
This
course
is to rinse while
supply
feeding
water
rinse
continuously.
Set the drain
Put the laundry into the
Set the rinse time with
123
selector to "WASH
wash tub and
the
the wash timer and feed
?
RINSE"
position.
open
water faucet.
water
continuously.
OFF
0OFF
0
15
3
WASH
WATER SELECTOR
12
DRAIN SELECTOR
6
WASH TIMER
9
HOW TO SPIN
1. Put the
dryer
laundry evenly
2. Put the
spin
Safety cover
down
laundry
safety
lightly.
horizontally
on the top of the laundry.
Close the spin dryer cover.
Set the spin timer according to the
following table.
3. Place the
4.
5.
into the
basket.
Spin
time
Type
cover
guide
of
clothing
Thin fabrics (synthetic fabrics,
Sweaters (synthetic fabrics)
Spin
mixed
Cotton underwear
Sheets,
?
?
fabrics)
time
1 minute
1~3minutes
3~5minutes
towels
5 minutes
If the
spin dryer basket is off-balance and vibrates excessively, stop the
spinning, rearrange the clothes evenly, and then resume spinning.
Should spinning fail to stop within 15 seconds after the spin dryer cover is
opened, the brake is out of order. Immediately stop using the machine and
request repair service.
11
1. Remove the laundry from the spin dryer basket and close the spin dryer cover,
2. If there is water in the wash tub, set the drain selector to "DRAIN" in
order to drain it out, and then put it back to "OFF"
3. Disconnect the power cord from the electrical outlet.
4. Clean the washing machine. (Refer to CARE AND
MAINTENANCE on page 13~14.)
5. Ensure without fail the Drain Selector is thrned to "OFF"
position after using the machine.
TABLE 1.
weight guide
of
Type
for clothes
clothing
Type
of fabric
Weight
Cotton
Handkerchief
Cotton
50 g
Bath towel
Cotton
300 g
Shirt
Mixed fabric
200 g
Socks
150 g
Mixed fabric
(1 pair)
Pajama (shirt and pants)
piece
(53oz)
(1.8oz)
(10.6oz)
(7.1oz)
(1.8oz)
(17.6oz)
(21.2oz)
(28.2oz)
(7.1oz)
per
Under shirt
50 g
Cotton
500 g
Winter undershirt
Cotton
600 g
Workclothes
Mixed fabric
800 g
Blouse
Mixed fabric
200 g
TABLE 2. GUIDE FOR WASHING
Type
Wash
selector
of fabric
Silk,
Woolen,
GENTLE
Knits
Cotton, Linen NORMAL
soiled
cotton and
STRONG
linen
Note
:
Amount of
laundry
Water
level
0.5~4.0kg
Synthetics,
Very
Wash time
?
Amount of
?
Detergent
(1.1~8.8lb)
2~5
4.0~4.7kg
(8.8~10.4lb)
min.
4.7~5.5kg
(10.4~12.1lb)
0.5~4.0kg
(1.1~8.8lb)
5~10
4.0~4.7kg
(8.8~10.4lb)
min.
4.7~5.5kg
(10.4~12.1lb)
0.5~4.0kg
(1.1~8.8lb)
10~15 4.0~4.7kg
(8.8~10.4lb)
min.
4.7kg~
(10.4lb~)
laundry is a weight of dry laundry.
a general synthetic detergent.
is
12
Amount of
Amount of
water
detergent
L
46
M
54
H
61
L
46
M
54
H
61
L
46
M
54
H
61
42~46g
(1.5~1.6oz)
51~55g
(1.8~1.9oz)
56~60g
(2.0~2.1oz)
42~46g
(1.5~1.6oz)
51~55g
(1.8~1.9oz)
56~60g
(2.0~2.1oz)
42~46g
(1.5~1.6oz)
51~55g
(1.8~1.9oz)
56~60g
(2.0~2.1oz)
CARE AND MAINTENANCE
?
Be
to disconnect the power cord from the electric outlet before
and maintenance.
sure
care
Washing
?
starting
machine
If the washing machine itself becomes dirty.
The washing machine can be cleaned with a mild liquid detergent. Never
abrasive cleanser or chemicals such as benzene or thinner to clean the
washing machine, because these materials will damage both the painted
surfaces and the plastic parts.
use
Pulsator
If a button or some other object gets caught in the pulsator.
1.Take out the pulsator cap with "-" type driver.
(only for WP-850Q, WP-860Q, WP-850G, WP-860G)
2.Use a screwdriver to loosen the screw in the center
of the pulsator, and lift the pulsator straight up in order
to remove the button or other object.
3. Replace the pulsator and tighten the screw.
4. Replace the pulsator cap.
Overflow filter & Rotation filter-C
123
A
?
Lift up the area
of the
flow filter.
Take out the rotation filter-C
by pulling in direction shown.
?
over
?
Pull the overflow filter
forward from the wash tub
in the direction of the
?
Tum the net over and
rinse in water
arrow.
456
?
Use
brush or your hand
all of the lints
which has adhered to the
overflow filter.
to
?
If
a
remove
only
rotation filter-C need
?
Insert the over flow filter
back into the wash tub.
washing, proceed
13
the process 1
?
Insert the rotation filter-C
back into the overflow
filter.
3
6
on
the upper
figure.
CARE AND MAINTENANCE
Spin dryer
If
becomes
clothing
1. Unscrew the
basket
trapped
screw
between the
2. Take hold of the front of the
3. Pull the tub
spin dryer
safety
at the left corner in the
safety
basket and the
spin
tub.
cover-1.
cover-1.
the other hand.
by
safety cover-1 upward.
Remove the article of clothing.
Close the safety cover-1, pressing down on it so that it fits securely
the spin tub.
Tighten the screw at the left corner in the safety cover-1.
4. Pull the
5.
6.
7.
into
Safety cover-1
Tub
TROUBLESHOOTING GUIDE
Before
Type
of
Requesting Service
Checking point
clothing
Motor does not operate,
?
?
Spin dryer
not
basket does
?
Is the power cord firmly plugged in?
Is the timer turned to a suitable point except "OFF"?
Is there any cloth dropped between the basket
and tub?
operate.
?
Is the
?
Is the
spin dryer cover closed?
laundry gathered to one side
of the
spin dryer
basket?
No
draining
?
?
plunger valve?
drain hose guide located
Is the lint stuck to the
Is the end of the
height?
?
Is the drain pump
14
operated?
at an exceed
W
D
H
Power
On SPECIFICATION LABEL
source
Water level
Water Pressure
Less than 100kPa
(1kgf/cm 2)
WP-850QP:820×482×983mm.(W×D×H)
Dimensions
WP-860QP:820×482×995mm.(W×D×H)
Weight (Net)
33
kg
How to read the manufactured month and year from the label stuck
back of the product.
on
the
EX)911TW00001
Serial No.
Product code
Month
Year
(The
last
Main service parts list
service call.
:
digit
to
year)
Refer to below listed parts
Part name
WASH MOTOR
SPIN MOTOR
-SDBASKET
CYCLE TIMER ASM
CAPACITOR
GEAR CASE ASM
name
Remark
90W
40W
PLASTIC
-
-
-
-
-
15
when you need
Download PDF

advertising