LG | LPP154 | Owner's Manual | LG LPP154 Owner’s Manual

LG LPP154 Owner’s Manual
LPP154_ENG-8861
8/26/09
3:14 PM
Page 1
ENGLISH
FRANÇAIS
Model: LPP154
PORTUGUÊS
As an ENERGY STAR® Partner,
LG has determined that this
product or product models meet
the ENERGY STAR® guidelines for
energy efficiency.
ENERGY STAR® is a U.S. registered mark.
P/NO : MFL39518861
LPP154_ENG-8861
8/26/09
3:14 PM
Page 2
Safety Precaution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined space such as a book case or
similar unit.
CAUTION: Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from over heating. The openings should be
never be blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instruction has been
adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain it for future reference. Should the
unit require maintenance, contact an authorized service center.
Use of controls, adjustments or the performance of procedures other than those
specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible
laser radiation when open. DO NOT STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and
no objects filled with liquids, such as vases, should be placed on the apparatus.
CAUTION: The speakers do not have magnetic shielding. Do not place the unit near
televisions, personal computers or other devices easily influenced by magnetism.
2
CAUTION: This product may receive radio interference caused by mobile telephones
during use. If such interference is apparent, please increase separation between the
product and the telephone.
CAUTION: Excessive sound pressure from earphones and headphones may cause
hearing loss.
CAUTION: Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional
outlets or branch circuits. Check the specification page of this owner's manual to be
certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized service center.
Protect the power cord from physical or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord plug. When installing the
product, ensure that the plug is easily accessible.
POWER: This unit operates on a mains supply of 230V, 50Hz.
WIRING: This unit is supplied with a BSI 1363 approved 13 amp mains plug, fused
at 3 amp. When replacing the fuse always use a 3 amp BS 1362, BSI or ASTA
approved type. Never use this plug with the fuse cover omitted. To obtain a
replacement fuse cover contact your dealer. If the type of plug supplied is not
suitable for the mains sockets in your home, then the plug should be removed and a
suitable type fitted. Please refer to the wiring instructions below:
WARNING: A mains plug removed from the mains lead of this unit must be
destroyed. A mains plug with bared wires is hazardous if inserted in a mains socket.
Do not connect either wire to the earth pin, marked with the letter E or with the earth
symbol
or coloured green or green and yellow.
If any other plug is fitted, use a 3 amp fuse, either in the plug, or at the distribution
board.
IMPORTANT: The wires in this mains lead are coloured in accordance with the
following codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the colours of the wires in the mains lead
of this unit may not correspond with the coloured marking identifying the terminals in
your plug, proceed as follows: The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or coloured black. The wire which is
coloured brown must be connected to the terminal which is marked with the letter L
or coloured red.
LPP154_ENG-8861
8/26/09
3:14 PM
Page 3
Contents
Speaker connection
Safety Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
a
Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Attach the speakers.
Align the speaker with the main unit as shown in the figure, interlock
the grooves and attach the speaker and main unit.
Power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Playing the auxiliary equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Listening to cassette tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
If you want to detach the speakers,
press the speaker release levers and
then detach each speaker and main unit.
Using the microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Other functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Setting the sound mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XDSS (Extreme Dynamic Sound System) . . . . . . . . . . . . . . . . . . . . . . . . .7
Using earphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Troubleshooting
Specifications
b
Connect the speaker cables.
Connect only positive (red) wires to positive (+) terminals and
negative (black) wires to negative (-) terminals.
This product is manufactured to comply with EMC Directive
2004/108/EC and Low Voltage Directive 2006/95/EC.
European representative:
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The Netherlands
(Tel : +31-036-547-8940)
3
LPP154_ENG-8861
8/26/09
3:14 PM
Page 4
Power source
AC Power Cord Connection
1 Connect one end of the AC power
cord (supplied) to the AC IN
socket located at the backside of
your unit.
2 Plug the other end into the wall
outlet.
Notes:
• Unplug the AC power cord from the wall outlet if you do not to use for an
extended period of time.
• During the AC power cord connect to the wall outlet, the batteries are not
worn out.
Battery Installation
1 Open the battery cover.
2 Put eight “D” (R20) batteries (not supplied) into the battery
compartment making sure the (+) and (-) are correctly positioned.
3 Replace the battery cover.
Notes:
• To avoid damage from possible battery leakage, remove the batteries if
you do not plan to use the unit for an extended period of time.
• When the batteries are weak, replace all the batteries with new ones.
4
DC power cord connection
1 Connect one end of the DC power
cord to the DC power input socket
(DC 12V).
2 Plug the other end into the DC
power output socket (cigarette
lighter socket etc.).
DC 12V
+
LPP154_ENG-8861
8/26/09
3:14 PM
Page 5
Main unit
6
5
4
7
8
3
9
18
17
16
2
15
19
14
20
10
1
11
12
13
21
1
Cassette holder
2
Left speaker (Woofer)
• Playback button (B PLAY)
3
Left speaker (Tweeter)
• Rewind button (bb REW)
4
• BAND switch (FM/MW/SW1/SW2)
• Fast forward button (BB FF)
• XDSS button
• Stop/eject button (x /Z STOP/EJECT)
• Audio input terminal (L-AUX IN-R)
12 • Recording button (z REC)
• Pause button (X PAUSE)
5
Frequency indicator
13 AC IN socket (AC ~)
6
Handle
14 Right speaker cord compartment
7
Operation/battery indicator (OPERATION/BATT)
15 Right speaker release lever
8
• Tuning control (TUNING)
16 DC power input socket (DC 12V)
• Voice optimizer button (VOICE OPT.)
17 Speaker terminals
• Headphones jack (PHONE)
18 Telescopic antenna
• Microphone (MIC.)
19 Left speaker release lever
Right speaker (Tweeter)
20 Left speaker cord compartment
9
10 Right speaker (Woofer)
21 Battery cover
11 • JAZZ/ROCK/POP/CLAS buttons
• FM MODE/RIF switch
• FUNCTION switch (TAPE/OFF, TUNER, AUX IN)
• Volume control (VOLUME)
5
LPP154_ENG-8861
8/26/09
3:14 PM
Page 6
Listening to the radio
Listen to cassette tapes
1 Set [FUNCTION] switch to “TUNER”.
“OPERATION/BATT” lights while the radio is on.
1 Set [FUNCTION] switch to “TAPE/OFF”.
2 Select “FM, MW, SW1 or SW2” by using [BAND] switch.
3 Insert the tape, with the playback side facing down.
3 Select a station by using tuning control (TUNING).
4 Close the cassette holder.
Listening to the radio - more you can do
2 Open the cassette holder by pressing [x /Z STOP/EJECT].
5 Press [B PLAY] to play the tape.
“OPERATION/BATT” lights while the tape is playing.
To turn the radio off
Set [FUNCTION] switch to “TAPE/OFF”.
Listening to cassette tapes - more you can do
To improve reception
To pause play
• FM: Raise and extend the whip antenna.
If stereo reception is poor, set [FM MODE/RIF] switch to “MONO”.
Press [X PAUSE].
Press once again to resume play.
• MW: Turn the unit to face in the direction of best reception.
• SW1/SW2: Raise and extend the whip antenna and keep it vertical.
Playing the auxiliary equipment
To stop play
Press [x /Z STOP/EJECT].
The unit is automatically stopped when the tape playback is completed.
To fast forward or rewind
Press [bb REW] or [BB FF].
Using the microphone
Microphone
1 Connect the auxiliary equipment to Audio input terminal (L-AUX
IN-R) of the unit by using an audio cable.
2 Set [FUNCTION] switch to “AUX IN”.
3 Turn the auxiliary equipment on and play it.
If you record through the auxiliary equipment, Refer to the
“Recording” on the page 7.
6
1 Play a source (Radio or tape).
2 Speak or sing into the microphone.
LPP154_ENG-8861
8/26/09
3:14 PM
Page 7
To record again, cover the hole of the tab with adhesive tape.
Recording
You can record from a source to tape.
1 Open the cassette holder and insert a blank tape.
Adhesive tape.
2 Close the cassette holder.
3 Select a source (FM, MW, SW1, SW2, AUX IN or MIC) in which
you want to record.
When recording the auxiliary equipment, Set [FUNCTION] switch to
“AUX IN” and then play it.
When recording through the microphone, Set [FUNCTION] switch to
“TAPE/OFF” and then speak or sing into the microphone.
4 Press [z REC].
Recording - more you can do
To pause recording
Press [X PAUSE].
To resume recording, press [X PAUSE] again.
Setting the sound mode
You can select five types of sound effects by pressing JAZZ, ROCK, POP,
CLAS or VOICE OPT. buttons.
The selected sound effect button lights.
-
JAZZ: Optimized for jazz music.
ROCK: Optimized for Hard Rock and Heavy Metal.
POP: Optimized for R&B, Soul and Country music.
CLAS: Optimized for orchestral music.
VOICE OPT.: No sound effects used.
XDSS (Extreme Dynamic Sound System)
To stop recording
Press [x /Z STOP/EJECT].
The unit is automatically stopped when the tape playback is completed.
Note
• Changes to volume and tone will not affect the recording.
• Wind up the leader tape before recording.
• When recording MW, set [FM MODE/RIF] to the position where there is
less noise.
• Removing the tab(s) of the cassette (with a small screwdriver) will
prevent accidental erasure.
Side A
Other functions
Press XDSS to reinforce treble, bass and the surround effect. The XDSS
button lights. To cancel, press XDSS again.
Using earphone
Connect a stereo headphone jack ( 3.5mm) to the Headphones jack
(PHONE) to listen to the sound through headphones. No sound can be
heard from speakers.
Avoid listening for prolonged periods of time to prevent hearing damage.
Tab for side A
Tab for side B
7
LPP154_ENG-8861
8/26/09
3:14 PM
Page 8
Troubleshooting
Symptom
Specifications
Cause
Correction
POWER
No power
The power cord is not plugged in.
The battery is not inserted
correctly.
The battery is not remaining.
Plug in the power cord.
Align the (+) and (-) polarities
properly when inserting the
batteries. Disconnect the AC
power cord when powered by
batteries.
Change the battery with a new
one.
RADIO
No sound
Some noise
occurs.
The function switch is not set to
the Radio mode.
There are electronic devices near
the player.
Set the switch to the Radio mode.
Record protect tabs are removed.
Cover holes on back edge of tape
with tap.
Set the player far from the
devices.
TAPE
Unable to record
General
Power supply
230 V, 50 Hz
Power consumption
25 W
Net Weight
5.2 kg
External dimensions (W x H x D)
566 x 270 x 239 mm
Output Power (T.H.D 10%)
5WX2
Speakers
8ΩX2
AC Operation
230 V, 50 Hz
Battery Operation
DC 12V, eight “D” (R20) batteries
(not supplied)
DC Operation
12 - 13.2 V
Tuner
FM
Tuning Range
Intermediate Frequency
MW
Tuning Range
Intermediate Frequency
SW1
Tuning Range
Intermediate Frequency
SW2
Tuning Range
Intermediate Frequency
Cassette tape player
Frequency Response
Signal to Noise Ratio
Designs and specifications are subject to change without notice.
88 - 108 MHz
10.7 MHz
530 - 1600 kHz
455 kHz
2.3 - 7.0 MHz
455 kHz
7.0 - 22 MHz
455 kHz
125 - 8000 Hz
40 dB
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising