LG | 32LG300C | LG 32LG300C Owner’s Manual

ENGLISH
LCD TV
OWNER’S MANUAL
LCD TV MODELS
2 2 L G 3 0* *
2 6 L G 3 0* *
3 2 L G 3 0* *
3 7 L G 3 0* *
4 2 L G 3 0* *
Please read this manual carefully before operating
your TV.
Retain it for future reference.
Record model number and serial number of the TV.
Refer to the label on the back cover and quote this
information.
To your dealer when requiring service.
Trade Mark of the DVB Digital Video
Broadcasting Project (1991 to 1996)
I D N u m b e r ( s ) : 5243: 22LG300C-ZA
5242: 26LG300C-ZA
5382: 32LG300C-ZA
5383: 37LG300C-ZA
5384: 42LG300C-ZA
P/NO: MFL34441619 (0810-REV03)
Printed in Korea
ACCESSORIES
Batteries
Owner’s Manual
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.
The accessories included may differ from the images below.
Dual Lock™
(This feature is not available for
all models.)
(Refer to P.11)
Remote Control
This feature is not available for all models.
Polishing Cloth
Protective Bracket and Bolt for Power Cord
(This feature is not available for all models.)
(Refer to P.10)
Power Cord
Polishing cloth for use on the screen.
Lightly wipe any stains or fingerprints on the surface
of the TV with the polishing cloth.
Do not use excessive force. This may cause scratching
or discolouration.
O n l y 2 2 L G 3 0* *
Cable Management Clip
Protection Cover
O n l y 2 6 / 3 2 / 3 7 / 4 2 L G 3 0* *
(Only 26/32/37/42LG30**)
x4
x4
or
Bolts for stand assembly
(Refer to P.8)
Screw for stand fixing
(Refer to P.11)
Protection Cover
(Refer to P.13)
1
CONTENTS
ACCESSORIES
.............................................
1
CONTENTS
PREPARATION
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 4
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . 6
Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Please set it up carefully so the product
does not fall over . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Back Cover for Wire Arrangement . . . . . . . . . . . . . 10
Attaching the TV to a desk . . . . . . . . . . . . . . . . . . . 11
Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Positioning your display . . . . . . . . . . . . . . . . . . . . . 12
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Kensington Security System . . . . . . . . . . . . . . . . . . 12
Protection cover . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . 14
Wall Mount: Horizontal installation . . . . . . . . . . . . 14
Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . 15
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . 16
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . 22
Insertion of CI Module . . . . . . . . . . . . . . . . . . . . . . 22
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
- Screen Setup for PC Mode . . . . . . . . . . . . . . . 26
WATCHING TV / PROGRAMME CONTROL
2
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
CI Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Selecting the Programme Table . . . . . . . . . . . . . . 45
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Remote Control Key Functions . . . . . . . . . . . . . . . 30
Turning on the TV . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programme Selection . . . . . . . . . . . . . . . . . . . . . . . 32
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 32
On-Screen Menus Selection and Adjustment . . . . 33
Auto Programme Tuning . . . . . . . . . . . . . . . . . . . . . 34
Manual Programme Tuning (In Digital Mode) . . . . 35
Manual Programme Tuning (In Analogue Mode) . . 36
Programme Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
EPG (ELECTRONIC PROGRAMME
GUIDE) (IN DIGITAL MODE)
Switch On/ Off EPG . . . . . . . . . . . . . . . . . . . . . . . . 47
Select Programme . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Button Function in NOW/NEXT Guide Mode . . . . . 47
Button Function in 8 Day Guide Mode . . . . . . . . . . 48
Button Function in Date Change Mode . . . . . . . . . . 48
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . 49
Preset Picture Settings
- Picture Mode-Preset . . . . . . . . . . . . . . . . . . . . 51
- Auto Colour Tone Control (Warm/Medium/Cool) . . . . .52
Manual Picture Adjustment
- Picture Mode-User option . . . . . . . . . . . . . . . . 53
Picture Improvement Technology . . . . . . . . . . . . . . . . . 54
Advanced - Film Mode . . . . . . . . . . . . . . . . . . . . . . 55
Advanced - Black(Darkness) Level . . . . . . . . . . . . . 56
Eye Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
SOUND & LANGUAGE CONTROL
Teletext within Digital Service . . . . . . . . . . . . . . . 78
Teletext in Digital Service . . . . . . . . . . . . . . . . . . 78
APPENDIX
CONTENTS
Auto Volume Leveler . . . . . . . . . . . . . . . . . . . . . . . . 59
Preset Sound Settings - Sound Mode . . . . . . . . . . 60
Sound Setting Adjustment - User Mode . . . . . . . . . . 61
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
I/II
- Stereo/Dual Reception (In Analogue Mode Only) . . . . 64
- NICAM Reception (In Analogue Mode Only) . . . . . . . 65
- Speaker Sound Output Selection . . . . . . . . . . 65
On-Screen Menu Language/Country Selection . . . . . . . . 66
Language selection (In Digital Mode only) . . . . . . 67
DIGITAL TELETEXT
Initializing (Reset to original factory setting) . . . . . 79
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Product Specifications . . . . . . . . . . . . . . . . . . . . . . 83
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
External Control Device Setup . . . . . . . . . . . . . . . 86
TIME SETTING
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Auto On/ Off Timer Setting . . . . . . . . . . . . . . . . . . 69
Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . 70
Time Zone Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . 71
Alarm setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . 72
Block Programme . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
TELETEXT
Switch On/ Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
SIMPLE Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
TOP Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
FASTEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Special Teletext Functions . . . . . . . . . . . . . . . . . . . . 77
3
PREPARATION
FRONT PANEL CONTROLS
■
■
Image shown may differ from your TV.
If your TV has a protection film attached, remove the film and then wipe the TV with a polishing cloth.
PREPARATION
22LG30**
INPUT
MENU
INPUT MENU OK
VOLUME
OK
-
PROGRAMME
+
-
P
+
POWER
Remote Control Sensor
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates blue when the TV is switched on.
Note: You can adjust Power Indicator in the OPTION
Clock LED
4
menu.
PREPARATION
26/32/37/42LG30**
+
P
-
PROGRAMME
+
VOLUME
-
OK
OK
MENU
MENU
Clock LED
INPUT
POWER
Remote Control Sensor
INPUT
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates blue when the TV is switched on.
Note: You can adjust Power Indicator in
the OPTION menu.
5
(
)
PREPARATION
BACK PANEL INFORMATION
A
Image shown may differ from your TV.
PREPARATION
PCMCIA CARD SLOT
22LG30**
1
3
4
5
MONO AUDIO R
VIDEO L/MONO
2
13
HDMI/DVI IN
14
AV
V IN 2
(
6
7
8
9
10
1
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.
2
HDMI Input
Connect a HDMI signal to HDMI IN. Or DVI (VIDEO)
signal to HDMI/DVI port with DVI to HDMI cable.
3
RGB/DVI Audio Input
Connect the audio from a PC or STB with DVI output.
4
11
12
Component Input
Connect a component video/audio input to these
jacks.
10
SPEAKER OUTPUT(MONO)
The phone socket for external speaker is on this
jack.
11
Euro Scart Socket (AV1)
Connect scart socket from an external device to
this jack.
RJP INTERFACE
Connect control line (RJ45) for RJP(Remote Jack pack)
12
Antenna Input
Connect RF antenna to this jack.
5
Remote Control Port
13
6
RGB Input
Connect the output from a PC.
PCMCIA (Personal Computer Memory Card
International Association) Card Slot
(This feature is not available in all countries.)
14
Audio/Video Input(AV2)
Connect audio/video output from an external
device to these jacks.
VIDEO L/MONO AUDIO R
PCMCIA CARD SLOT
9
AV IN 2
7
8
6
)
SERVICE ONLY PORT
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
(
1
3
4
5
MONO AUDIO R
VIDEO L/MONO
2
13
PREPARATION
PCMCIA CARD SLOT
26/32/37/42LG30**
)
14
AV
V IN 2
(
6
7
8
9
1
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.
2
HDMI Input
Connect a HDMI signal to HDMI IN. Or DVI (VIDEO)
signal to HDMI/DVI port with DVI to HDMI cable.
3
RGB/DVI Audio Input
Connect the audio from a PC or STB with DVI output.
4
)
10
11
12
Component Input
Connect a component video/audio input to these
jacks.
10
SPEAKER OUTPUT(MONO)
The phone socket for external speaker is on this
jack.
11
Euro Scart Socket (AV1)
Connect scart socket from an external device to
this jack.
RJP INTERFACE
Connect control line (RJ45) for RJP(Remote Jack pack)
12
Antenna Input
Connect RF antenna to this jack.
5
Remote Control Port
13
6
RGB Input
Connect the output from a PC.
PCMCIA (Personal Computer Memory Card
International Association) Card Slot
(This feature is not available in all countries.)
14
Audio/Video Input(AV2)
Connect audio/video output from an external
device to these jacks.
7
8
VIDEO L/MONO AUDIO R
PCMCIA CARD SLOT
9
AV IN 2
SERVICE ONLY PORT
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
7
Stand installation
A
Image shown may differ from your TV.
For 22LG30**
For 26/32/37/42LG30**
PREPARATION
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Assemble the parts of the S T A N D B O D Y with
C O V E R B A S E of the TV. Insert the S T A N D
B O D Y into a C O V E R B A S E until clicking sound.
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV.
STAND BODY
STAND BODY
COVER BASE
COVER BASE
3
8
3
Assemble the TV as shown.
4
Fix the 4 bolts securely using the holes in the
back of the TV.
Assemble the TV as shown.
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT
FALL OVER.
■
■
1
PREPARATION
■
You should purchase necessary components to fix the TV to the wall on the market.
Position the TV close to the wall to avoid the possibility of it falling when pushed.
The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the
possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This
will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
2
1
Use the eye-bolts or TV brackets/bolts to fix the TV to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen these bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
2
Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the
wall.
3
3
Use a sturdy rope to tie the TV. It is safer to tie the rope so it becomes horizontal between the wall and the
TV.
! NOTE
G
G
G
When moving the TV undo the cords first.
Use a platform or cabinet strong and large enough to support the size and weight of the TV.
To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
9
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
A
Image shown may differ from your TV.
For 22LG30**
For 26/32/37/42LG30**
PREPARATION
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the PROTECTIVE
BRACKET and the screw as shown. It will help prevent
the power cable from being removed by accident.
1
1
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the PROTECTIVE
BRACKET and the screw as shown. It will help prevent
the power cable from being removed by accident.
PROTECTIVE
BRACKET
(This feature is not
available for all models.)
2
PROTECTIVE
BRACKET
(This feature is not
available for all models.)
Install the CABLE MANAGEMENT CLIP as shown.
2
Install the CABLE MANAGEMENT CLIP as
shown.
CABLE MANAGEMENT CLIP
3
Fit the CABLE MANAGEMENT CLIP as shown.
CABLE MANAGEMENT CLIP
3
Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.
How to remove the
CABLE MANAGEMENT CLIP
G
Hold the CABLE MANAGEMENT CLIP with both hands
and pull it backward.
! NOTE
G
10
Do not hold the CABLE MANAGEMENT CLIP when moving the TV.
- If the TV is dropped, you may be injured or the product may be broken.
Attaching the TV to a desk (Only 26/32/37/42LG30**)
The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product. Use only an attached screw.
Stand
PREPARATION
1-Screw
(provided as parts of the product)
Desk
! WARNING
G
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.
Swivel Stand (Only 26/32/37/42LG30**)
After installing the TV, you can adjust the TV manually
to the left or right direction by 20 degrees to suit your
viewing position.
How to use Dual Lock™ (This feature is not available for all models.)
Fix the set-top box to the TV and use it when you want to.
1
After removing the protection paper from
the Dual Lock, stick it to the TV and the
set-top box as shown.
2
Attach the set-top box to the TV by pressing
the Velcro strips together.
11
PREPARATION
POSITIONING YOUR DISPLAY (Only 22LG30**)
• Tilt range
■
■
PREPARATION
Image shown may differ from your TV.
Adjust the position of the panel in various ways for
maximum comfort.
12
0
0
3
LOCATION (Only 22LG30**)
Position your TV so that no bright light or sunlight falls directly onto the screen. Care should be taken not to
expose the tv to any unnecessary vibration, moisture, dust or heat. Also ensure that the TV is placed in a position
to allow a free flow of air. Do not cover the ventilation openings on the back cover.
If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the back of
the TV.
When you install the TV to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.
KENSINGTON SECURITY SYSTEM (Only 22LG30**)
The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington
Security System cable as shown below.
For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with
the Kensington Security System.
For further information, contact http://www.kensington.com, the internet homepage of the Kensington
company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD
projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the TV feels cold to the touch, there may be a small “flicker” when
when it is turned on.
This is normal, there is nothing wrong with TV.
b. Some minute dot defects may be visible on the screen, appearing as
tiny red, green, or blue spots. However, they have no adverse effect on
the monitor's performance.
c. Avoid touching the LCD screen or holding your finger(s)
against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
12
PROTECTION COVER
■
Image shown may differ from your TV.
For 22LG30**
For 26/32/37/42LG30**
Loose the bolts from TV.
2
Bend the H I N G E B O D Y and pull it backward.
When installing the wall-mounted unit, use the protection cover for desk-type stand installation. Insert
the P R O T E C T I O N C O V E R into the TV until clicking sound.
PREPARATION
1
or
HINGE BODY
3
Insert the P R O T E C T I O N C O V E R into the TV.
PROTECTION COVER
4
Fix the 4 bolts securely using the holes in the
back of the TV.
13
■
■
The TV can be installed in various ways such as on a wall, or on a desktop etc.
The TV is designed to be mounted horizontally.
EARTHING
PREPARATION
Ensure that you connect the earth wire to prevent possible
electric shock. If grounding methods are not possible, have a
qualified electrician install a separate circuit breaker.
Do not try to earth the TV by connecting it to telephone
wires, lightening rods or gas pipes.
Power Supply
Circuit
breaker
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV.
4 inches
4 inches
4 inches
4 inches
WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV. We recommend that you
use a wall mounting bracket of LG brand when mounting the TV to a wall.
4 inches
4 inches
4 inches
4 inches
4 inches
14
■
To prevent damage do not connect to the mains outlet until all connections are made between the devices.
ANTENNA CONNECTION
For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
■
PREPARATION
Wall
Antenna
Socket
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
HDMI/DVI IN
(
)
(
)
VIDEO L/MONO AUDIO R
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
PCMCIA CARD SLOT
RF Coaxial Wire (75 ohm)
Outdoor
Antenna
(VHF, UHF)
AV IN 2
UHF
Antenna
HDMI/DVI IN
Signal
Amplifier
VHF
PCMCIA CARD SLOT
■
In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the
antenna as shown above.
If signal needs to be split for two TVs, use an antenna signal splitter for connection.
VIDEO L/MONO AUDIO R
■
AV IN 2
15
EXTERNAL EQUIPMENT SETUP
■
■
To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 26LG30** models.
HD RECEIVER SETUP
■
PREPARATION
16
This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive
Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.
Connecting with a component cable
1
Connect the video outputs (Y, PB, PR) of the digital set
top box to the C O M P O N E N T I N V I D E O jacks on the TV.
2
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O jacks on the TV.
3
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
4
Select C o m p o n e n t input source using the I N P U T button
on the remote control.
Signal
Component
HDMI
480i/576i
Yes
No
480p/576p
Yes
Yes
720p/1080i
Yes
Yes
1080p
Yes
Yes
1
2
HDMI/DVI IN
Connecting a set-top box with an HDMI cable
1
Connect the HDMI output of the digital set-top box to the
H D M I / D V I I N 1 ( D V I ) or H D M I / D V I I N 2 jack on the
TV.
EXTERNAL EQIPMENT SETUP
2
HDMI/DVI IN
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
1
3
Select HDMI1 or HDMI2 input source using the I N P U T button on the remote control.
Connecting with a HDMI to DVI cable
1
Connect the digital set-top box to H D M I / D V I I N
1 ( D V I ) jack on the TV.
2
Connect the audio output of the digital set-top box to
the A U D I O I N ( R G B / D V I ) jack on the TV.
3
Turn on the digital set-top box. (Refer to the owner’s
manual for the digital set-top box.)
4
Select H D M I 1 input source using the I N P U T button
on the remote control.
1
2
17
HDMI/DVI IN
EXTERNAL EQUIPMENT SETUP
DVD SETUP
When connecting with a component cable
EXTERNAL EQIPMENT SETUP
1
Connect the video outputs (Y, PB, PR) of the DVD to the
C O M P O N E N T I N V I D E O jacks on the TV.
2
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O jacks on the TV.
3
Turn on the DVD player, insert a DVD.
4
Select C o m p o n e n t input source using the I N P U T button
on the remote control.
5
Refer to the DVD player's manual for operating instructions.
1
2
Component Input ports
To achieve better picture quality, connect a DVD player to
the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Connecting with a Euro Scart cable
1
Connect the Euro scart socket of the DVD to the A V 1
Euro scart socket on the TV.
2
Turn on the DVD player, insert a DVD.
3
Select A V 1 input source using the I N P U T button on the
remote control.
4
HDMI/DVI IN
1
Refer to the DVD player's manual for operating instructions.
! NOTE
G
18
Any Euro scart cable used must be signal shielded.
AUDIO/
VIDEO
(R) AUDIO (L)
Connecting the HDMI cable
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1 ( D V I ) or H D M I / D V I I N 2 jack on
the TV.
2
Select H D M I 1 or H D M I 2 input source using the
I N P U T button on the remote control.
3
Refer to the DVD player's manual for operating instructions.
1
! NOTE
G The
TV can receive video and audio signals simultaneously
when using a HDMI cable.
G If the DVD does not support Auto HDMI, you must set the
output resolution appropriately.
EXTERNAL EQIPMENT SETUP
1
HDMI/DVI IN
SPEAKER OUTPUT SETUP
1
Connect the external speaker to the S p e a k e r
o u t p u t ( M O N O ) jack on the TV.
2
Refer to the ‘Speaker & Speaker Stand’ manual for
operating instructions.
(
)
1
19
EXTERNAL EQUIPMENT SETUP
VCR SETUP
■
■
To avoid picture noise (interference), allow adequate distance between the VCR and TV.
If 4:3 picture format is used for an extended period the fixed images on the sides of the screen may remain
visible.
When connecting with a RF Cable
EXTERNAL EQIPMENT SETUP
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
VIDEO
L
1
2
Wall Jack
Antenna
20
1
Connect the A N T O U T socket of the VCR to the A N T E N N A I N socket on the
TV.
2
Connect the antenna cable to the A N T I N socket of the VCR.
3
Press the PLAY button on the VCR and match the appropriate channel between
the TV and VCR for viewing.
R
Connecting with a Euro Scart cable
Connect the Euro scart socket of the VCR to the A V 1
Euro scart socket on the TV.
2
Insert a video tape into the VCR and press PLAY on
the VCR. (Refer to the VCR owner’s manual.)
3
Select A V 1 input source using the I N P U T button on
the remote control.
EXTERNAL EQIPMENT SETUP
1
1
! NOTE
G
Any Euro scart cable used must be signal shielded.
AUDIO/
VIDEO
(R) AUDIO (L)
Connecting with a RCA cable
L
V I D E O jacks between TV and
Connect the A U D I O/V
VCR. Match the jack colours (Video = yellow, Audio Left
= white, and Audio Right = red)
2
Insert a video tape into the VCR and press PLAY on
the VCR. (Refer to the VCR owner’s manual.)
3
Select A V 2 input source using the I N P U T button on
the remote control.
OUTPUT
SWITCH
VIDEO S-VIDEO
ANT IN
ANT OUT
L/MONO
MONO AUDIO R
VIDEO L/
1
R
AV IN 2
! NOTE
G
If you have a mono VCR, connect the audio cable from the
VCR to the A U D I O L / M O N O jack of the TV.
21
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
Camcorder
Video Game Set
1
V I D E O jacks between TV and
Connect the A U D I O/V
external equipment. Match the jack colours. (Video =
yellow, Audio Left = white, and Audio Right = red)
EXTERNAL EQIPMENT SETUP
2
3
Select A V 2 input source using the I N P U T button on
the remote control.
Operate the corresponding external equipment.
Refer to external equipment operating guide.
L/MONO
MONO AUDIO R
VIDEO L/
VIDEO
1
AV
V IN 2
- To view the encrypted (pay) services in digital TV
mode.
- This feature is not available in all countries.
1
Insert the CI Module to P C M C I A (Personal Computer
Memory Card International Association) C A R D S L O T
of TV as shown.
For further information, see p.44
22
PCMCIA CARD SLOT
INSERTION OF CI MODULE
1
TV
L
R
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
Connecting with a D-sub 15 pin cable
Connect the RGB output of the PC to the R G B I N
( P C ) jack on the TV.
2
Connect the PC audio output to the A U D I O I N
( R G B / D V I ) jack on the TV.
3
Turn on the PC and the TV
4
Select R G B input source using the INPUT button on
the remote control.
1
RGB OUTPUT
EXTERNAL EQIPMENT SETUP
1
2
AUDIO
Connecting with a HDMI to DVI cable
1
Connect the DVI output of the PC to the H D M I / D V I I N
1 ( D V I ) jack on the TV.
2
Connect the PC audio output to the A U D I O I N
( R G B / D V I ) jack on the TV.
3
Turn on the PC and the TV.
4
Select H D M I 1 input source using the I N P U T button
on the remote control.
HDMI/DVI IN
HDMI/DVI IN
1
2
DVI-PC OUTPUT
AUDIO
23
EXTERNAL EQUIPMENT SETUP
Supported Display Resolution
RGB[PC], HDMI[PC] mode
Resolution
720x400
EXTERNAL EQIPMENT SETUP
640x480
800x600
832x624
1024x768
1280x768
1360x768
1366x768
1400x1050
1680x1050
HDMI[DTV] mode
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.469
31.469
37.684
37.879
46.875
49.725
48.363
56.470
60.123
47.78
47.72
47.56
64.744
62.290
70.08
59.94
75.00
60.31
75.00
74.55
60.00
70.00
75.029
59.87
59.8
59.6
59.948
59.954
* Only 22LG30**
24
Resolution
640x480
720x480
720x576
1280x720
1920x1080
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.469
31.469
31.47
31.50
31.25
37.500
44.96
45.00
33.72
33.75
28.12
27.000
33.75
56.25
67.43
67.5
59.94
60.00
59.94
60.00
50.00
50
59.94
60.00
59.94
60.00
50.00
24.00
30.00
50.00
59.94
60.00
! NOTE
G To
G If
using a sound card, adjust PC sound as required.
TV uses a VESA Plug and Play Solution. The
TV provides EDID data to the PC system with a
DDC protocol. The PC adjusts automatically when
using this TV.
G DDC protocol is preset for RGB (Analog RGB),
HDMI (Digital RGB) mode.
G If required, adjust the settings for Plug and Play
functionality.
G If the graphic card on the PC does not output
analogue and digital RGB simultaneously, connect
only one of either RGB or HDMI IN (or HDMI/DVI
IN) to display the PC output on the TV.
G If the graphic card on the PC does output
analogue and digital RGB simultaneously, switch
the TV to either RGB or HDMI; (the other mode is
set to Plug and Play automatically by the TV.)
G DOS mode may not work depending on the video
card if you use a HDMI to DVI cable.
G If you use too long an RGB-PC cable, there may be
interference on the screen. We recommend using
under 5m of cable. This provides the best picture
quality.
G This
EXTERNAL EQIPMENT SETUP
enjoy vivid picture and sound, connect a PC to
the TV.
G Avoid keeping a fixed image on the TV’s screen for
prolonged periods of time. The fixed image may
become permanently imprinted on the screen; use
a screen saver when possible.
G Connect the PC to the RGB (PC) or HDMI/DVI IN
port of the TV; change the resolution.
G There may be interference relating to resolution,
vertical pattern, contrast or brightness in PC
mode. Change the PC mode to another resolution
or change the refresh rate to another rate or
adjust the brightness and contrast on the menu
until the picture is clear. If the refresh rate of the
PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of
the PC graphic card.
synchronization input waveform for
G The
Horizontal and Vertical frequencies are separate.
G Connect the signal cable from the monitor output
port of the PC to the RGB (PC) port of the TV or
the signal cable from the HDMI output port of the
PC to the HDMI/DVI IN port on the TV.
G Connect the audio cable from the PC to the Audio
input on the TV. (Audio cables are not included
with the TV).
25
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Screen Reset
Returns to the default settings Position, Size and Phase at the factory.
This function works in the following mode : RGB[PC].
EXTERNAL EQIPMENT SETUP
PICTURE
Move
OK
SCREEN
Move
BACK
Prev.
D
• Contrast
: 70
• Brightness
: 50
• Sharpness
: 50
• Colour
: 50
• Tint
:0
• Advanced Control
• Picture Reset
Screen
1MENU
Resolution
Auto Config.
To Set
Position
Size
Phase
Reset
G
Select PICTURE.
2
OK
Select SCREEN.
OK
Select Reset.
OK
Select Yes.
3
4
5
OK
Run Reset.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
26
Adjustment for screen Position, Size, Phase
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the
picture phase manually.
This function works in the following mode : RGB[PC].
Move
OK
SCREEN
BACK
Move
Prev.
D
• Contrast
: 70
• Brightness
: 50
• Sharpness
: 50
• Colour
: 50
• Tint
:0
• Advanced Control
• Picture Reset
Resolution
Auto Config.
D
Position
F
G
E
Size
Phase
Screen
1MENU
G
EXTERNAL EQIPMENT SETUP
PICTURE
Reset
Select PICTURE.
2
OK
Select SCREEN.
OK
Select Position, Size or Phase.
3
4
Make appropriate adjustments.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
27
EXTERNAL EQUIPMENT SETUP
Selecting Resolution
To view a normal picture, match the resolution of RGB mode and selection of PC mode.
This function works in the following mode: RGB[PC] mode.
EXTERNAL EQIPMENT SETUP
PICTURE
Move
OK
SCREEN
Move
BACK
Prev.
D
• Contrast
: 70
• Brightness
: 50
• Sharpness
: 50
• Colour
: 50
• Tint
:0
• Advanced Control
• Picture Reset
Resolution
Auto Config.
Position
1024 x 768
1280 x 768
1360 x 768
1366 x 768
Size
Phase
Screen
1MENU
G
Reset
Select PICTURE.
2
OK
Select SCREEN.
OK
Select Resolution.
3
4
Select the desired resolution.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
28
Auto Configure (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, your TV is functioning properly but needs further adjustment.
PICTURE
Move
OK
SCREEN
Move
BACK
Prev.
D
• Contrast
: 70
• Brightness
: 50
• Sharpness
: 50
• Colour
: 50
• Tint
:0
• Advanced Control
• Picture Reset
Resolution
Auto Config.
Position
To Set
Size
Phase
Screen
1MENU
G
EXTERNAL EQIPMENT SETUP
Auto configure
This function is for automatic adjustment of the screen position, clock, and phase The displayed image will
be unstable for a few seconds while the auto configuration is in progress.
Reset
Select PICTURE.
• If the position of the image is still not correct,
try Auto adjustment again.
2
• If picture needs to be adjusted again after Auto
OK
Select SCREEN.
OK
Select Auto Config..
adjustment in RGB (PC), you can adjust the
P o s i t i o n, S i z e or P h a s e.
3
4
OK
Select Yes.
5
OK
Run Auto Config..
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
29
WATCHING TV / PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
POWER Switches the TV on from standby or off to standby.
D/A TV Selects digital or analogue mode.
Switches the TV on from standby.
INPUT External input mode rotate in regular sequence.
Switches the TV on from standby.
WATCHING TV / PROGRAMME CONTROL
TV/RADIO Selects Radio or TV channel in digital mode.
I/II Selects the sound output.
MUTE Switches the sound on or off.
0~9 number Selects a programme.
button Selects numbered items in a menu.
LIST Displays the programme table.
Q.VIEW Returns to the previously viewed programme.
MENU Selects a menu.
EXIT Clears all on-screen displays and returns to TV viewing
from any menu.
INFO i Shows the present screen information.
GUIDE Shows programme schedule.
THUMBSTICK Allows you to navigate the on-screen menus and adjust
(Up/Down/Left the system settings to your preference.
Right)
OK Accepts your selection or displays the current mode.
VOLUME UP Adjusts the volume.
/DOWN
BACK Allows the user to move back one step in an interactive
application, EPG or other user interaction function.
ALARM Sets the alarm function.
FAV Displays the selected favourite programme.
Programme Selects a programme.
UP/DOWN
30
1
TELETEXT These buttons are used for teletext.
BUTTONS For further details, see the ‘Teletext’ section.
1
Coloured These buttons are used for teletext (on T E L E T E X T
buttons models only) or P r o g r a m m e e d i t.
SLEEP Sets the sleep timer.
SUBTITLE Recalls your preferred subtitle in digital mode.
WATCHING TV / PROGRAMME CONTROL
RATIO Selects your desired picture format.
1
Installing Batteries
■
Open the battery compartment cover on the back and install the
batteries matching correct polarity (+with +,-with -).
■
Install two 1.5V AAA batteries. Do not mix old or used batteries
with new ones.
■
Close cover.
31
WATCHING TV / PROGRAMME CONTROL
TURNING ON THE TV
- When your TV is turned on, you will be able to use its features.
WATCHING TV / PROGRAMME CONTROL
1
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
2
In standby mode to turn TV on, press the r / I, INPUT or P + button on the TV or press the POWER, INPUT, P + - or NUMBER
button on the remote control and the TV will switch on.
Initializing setup
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the
L a n g u a g e, C o u n t r y, T i m e Z o n e, A u t o p r o g r a m m e t u n i n g.
Note:
a. It will automatically disappear after approx. 40 seconds unless a button is pressed.
b. Press the BACK button to change the current OSD to the previous OSD.
c. For those countries without confirmed DTV broadcasting standards, some DTV features might not work,
depending on the DTV broadcasting environment.
PROGRAMME SELECTION
1
Press the P + - or NUMBER buttons to select a programme number.
VOLUME ADJUSTMENT
1
Press the
+ - button to adjust the volume.
If you wish to switch the sound off, press the MUTE button.
You can cancel this function by pressing the MUTE,
button.
32
+ -, or I/II
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
SETUP
Move
OK
PICTURE
Aspect Ratio
Picture Mode
Move
: 16:9
: Vivid
• Backlight
• Contrast
• Brightness
• Sharpness
• Colour
• Tint
100
100
50
70
70
0
OK
R
G
E
AUDIO
SETUP
PICTURE
TIME
Auto Volume
Balance
Sound Mode
AUDIO
OPTION
LOCK
Move
OK
: Off
: Standard
• 120Hz
• 200Hz
• 500Hz
• 1.2KHz
• 3KHz
0
L
R
0
0
0
0
0
-
+
-
+
-
+
-
+
-
+
E
TIME
Move
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
Time Zone
OPTION
OK
Move
Menu Language : English
Audio Language : English
Subtitle Language : English
Hard of Hearing( ) Off
Country
:UK
Input Label
Key Lock
: Off
Set ID
:1
: Off
: Off
: Off
: Off
: Canary GMT
OK
LOCK
Move
WATCHING TV / PROGRAMME CONTROL
Auto tuning
Manual tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
OK
Lock System
: Off
Set Password
Block Programme
Parental Guidance : Off
E
1MENU
Display each menu.
2
OK
Select a menu item.
3
OK
Move to the pop up menu.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
33
WATCHING TV / PROGRAMME CONTROL
AUTO PROGRAMME TUNING
Use this to automatically find and store all available programmes.
When you start auto programming in digital mode, all previously stored service information will be deleted.
WATCHING TV / PROGRAMME CONTROL
SETUP
Move
SETUP
OK
Auto
Autotuning
tuning
Manual tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
1MENU
Move
Auto
Autotuning
tuning
Manual tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
Select SETUP.
OK
All service-information will be updated.
Continue?
Yes
No
SECAM L Search
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
2
• If you wish to keep on auto tuning select YES
OK
Select Auto Tuning.
OK
Select Yes.
OK
Run Auto tuning.
using the F G button. Then, press the OK
button. Otherwise select NO.
3
4
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
34
MANUAL PROGRAMME TUNING (IN DIGITAL MODE)
Manual Tuning lets you manually add a programme to your programme list.
Move
SETUP
OK
Auto tuning
Manualtuning
tuning
Manual
Move
Auto tuning
Manual
Manualtuning
tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
OK
F
DTV
G
Your receiver will add this
channel to your channel list.
UHF CH.
Bad
30
Normal
Good
ADD
Close
1MENU
Select SETUP.
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
2
OK
Select Manual Tuning.
OK
Select DTV.
WATCHING TV / PROGRAMME CONTROL
SETUP
3
4
Select the desired channel number.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
35
WATCHING TV / PROGRAMME CONTROL
MANUAL PROGRAMME TUNING (IN ANALOGUE MODE)
Manual Tuning lets you manually tune and arrange the stations in whatever order you desire.
WATCHING TV / PROGRAMME CONTROL
SETUP
Move
SETUP
OK
Auto tuning
Manualtuning
tuning
Manual
Move
OK
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
TV
F
Auto tuning
Manual
Manualtuning
tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
G
Storage
2007
System
BG
Band
V/UHF
Channel
Fine
Search
Name
0
F G
F G
C 02
Store
Close
1MENU
6
Select SETUP.
Select V/UHF or Cable.
7
2
or
Select Manual Tuning.
OK
1
2
4
5
6
7
8
9
3
Select the desired
channel number.
0
8
3
OK
Commence searching.
Select TV.
4
or
1
2
4
5
6
7
8
9
0
3
9
Select the desired programme number on.
OK
Select Store.
5
Select a TV system.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
• Use NUMBER buttons to input a 4-digit password in Lock System ‘On’.
• L : SECAM L/L’ (France)
BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa / Australia)
I : PAL I/II (U.K. / Ireland / Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
• To store another channel, repeat steps 4 to 9.
36
A
Assigning a station name
You can assign a station name with five characters to each programme number.
1MENU
5
Select SETUP.
OK
OK
Select Manual Tuning.
6
3
OK
OK
Select Close.
OK
Select Store.
Select TV.
7
4
Select Name.
A
Fine Tuning
WATCHING TV / PROGRAMME CONTROL
2
Select the position and make
your choice of the second character, and so on.
You can use an the alphabet A
to Z , the number 0 to 9 , +/ -,
and blank.
Normally fine tuning is only necessary if reception is poor.
1MENU
4
Select SETUP.
Select Fine.
2
5
OK
Select Manual Tuning.
OK
Select TV.
3
Fine tune for the best picture and
sound.
6
OK
Select Store.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
37
WATCHING TV / PROGRAMME CONTROL
PROGRAMME EDIT
When a programme number is skipped, it means that you will be unable to select it using P + / - button during TV
viewing.
If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or
select it in the Programme edit menu
This function enables you to skip the stored programmes.
In some countries it is possible to move a programme number by using the YELLOW button only.
WATCHING TV / PROGRAMME CONTROL
SETUP
Move
OK
Auto tuning
Manual tuning
Programme
ProgrammeEdit
Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
1MENU
Select SETUP.
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
2
OK
Select Programme Edit.
3
OK
Enter the Programme Edit.
4
Select a programme to be stored or skipped.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
38
(IN DTV/RADIO MODE)
A
Skipping a programme number
1
Select a programme number to be skipped.
BLUE
Turn the skipped programme number to blue.
3
BLUE
A
that you will be unable to select it using the P
+ / - button during normal TV viewing.
• If you wish to select a skipped programme, directly
enter the programme number with the NUMBER
buttons or select it in the programme edit or EPG.
Release the skipped programme.
Selecting favourite programme
1
FAV
Select your favourite programme number.
• It will automatically include the selected
programme into your favourite programme list.
WATCHING TV / PROGRAMME CONTROL
2
• When a programme number is skipped it means
39
WATCHING TV / PROGRAMME CONTROL
IN TV MODE
This function enables you to delete or skip the stored programmes.
You can also move some channels to other programme numbers.
A
Auto Sort
1
GREEN
Start Auto Sort.
• After activating Auto Sort once, you can no longer
edit programmes.
WATCHING TV / PROGRAMME CONTROL
Deleting a programme
A
1
Select a programme number to be deleted.
• The selected programme is deleted, all the fol-
lowing programmes are shifted up one
2
RED
Turn the deleted programme number to red.
3
RED
A
Release the deleted programme.
Moving a programme
1
Select a programme number to be moved.
2
Turn the moved programme number to YELLOW.
YELLOW
3
YELLOW
A
Release the moved programme.
Skipping a programme number
1
Select a programme number to be skipped.
2
BLUE
Turn the skipped programme number to blue.
3
BLUE
A
that you will be unable to select it using the P
+ / - button during normal TV viewing.
• If you wish to select a skipped programme, directly
enter the programme number with the NUMBER buttons or select it in the programme edit or EPG.
Release the skipped programme.
Selecting a Favourite Programme
1
FAV
40
• When a programme number is skipped it means
Select your favourite programme number.
• The selected programme will be added to the
favourite programme list.
BOOSTER (IN DIGITAL MODE ONLY)
If reception is poor, selectBooster to On.
When the signal is strong, select “Off”.
Move
OK
Auto tuning
Manual tuning
Programme Edit
Booster
:: On
Booster
On
Software Update : Off
Diagnostics
CI Information
1MENU
SETUP
Move
Auto tuning
Manual tuning
Programme Edit
Booster
:: On
Booster
On
Software Update : Off
Diagnostics
CI Information
OK
Off
On
On
Select SETUP.
2
OK
Select Booster.
OK
Select On or Off.
WATCHING TV / PROGRAMME CONTROL
SETUP
3
4
OK
Save.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
41
WATCHING TV / PROGRAMME CONTROL
SOFTWARE UPDATE
Software Update means software can be downloaded through the digital terrestrial broadcasting system.
SETUP
Move
SETUP
OK
WATCHING TV / PROGRAMME CONTROL
Auto tuning
Manual tuning
Programme Edit
Booster
: On
Software
Software Update
Update :: Off
Off
Diagnostics
CI Information
1MENU
Auto tuning
Manual tuning
Programme Edit
Booster
: On
Software
Software Update
Update :: Off
Off
Diagnostics
CI Information
3
Select SETUP.
Select Software Update.
OK
Off
Off
On
Select On or Off.
• If you select On, a user
confirm message box will be
displayed to notify that new
software is found.
OK
2
OK
Move
4
OK
Save.
* When setting “Software Update”
Occasionally, a transmission of
updated digital software information will result in the following
menu on the TV screen.
Select the Y E S using the F G
button and when you see the
following picture.
After Software Update is completed, the System takes about
one minute to restart.
- During Progress of a Software Update, please note the following:
• Power to the TV must not be interrupted.
• The TV must not be switched off.
• The antenna must not be disconnected.
• After Software Update, you can confirm the updated software version in Diagnostics menu.
42
DIAGNOSTICS (IN DIGITAL MODE ONLY)
This function enables you to view information on the Manufacturer, Model/Type, Serial Number and Software
Version.
This displays the information and signal strength of the tuned MUX.
This displays the signal information and service name of the selected MUX.
SETUP
Move
Engineering Diagnostics
OK
: LG Electronics Inc.
: 22LG300C
: 708KGKG00019
: V1.18.1
D
CH 30
CH 34
CH 36
CH 38
CH 54
CH 60
E
BACK Prev.
1MENU
EXIT Exit
Select SETUP.
2
Select Diagnostics.
OK
3
OK
WATCHING TV / PROGRAMME CONTROL
Manufacturer
Model/Type
Serial No.
Software Version
Auto tuning
Manual tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
Diagnostics
CI Information
Display Manufacturer, Model/Type, Serial Number and Software Version.
4
OK
Display the information of Channel.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
43
WATCHING TV / PROGRAMME CONTROL
CI [COMMON INTERFACE] INFORMATION
This function enables you to watch some encrypted services (pay services). If you remove the CI Module, you
cannot watch pay services.
When the module is inserted into the CI slot, you can access the module menu.
To purchase a module and smart card, contact your dealer. Do not repeatedly insert or remove a CAM module
from the TV. This may cause a malfunction. When the TV is turned on after inserting a CI Module, you may not
have any sound output.
This may be incompatible with the CI module and smart card.
CI (Common Interface) functions may not be possible depending upon the country broadcasting circumstances.
WATCHING TV / PROGRAMME CONTROL
Viaccess Module
SETUP
Move
OK
Consultations
Authorizations
Auto tuning
Manual tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
Information
CI
1MENU
Module information
Select the item
• This OSD is only for illustration and the menu options
and screen format will vary according to the Digital pay
services provider.
• It is possible for you to change CI (Common Interface)
menu screen and service by consulting your dealer.
Select SETUP.
2
OK
3
OK
4
OK
Select CI Information.
Select the desired item: Module information, smart card
information, language, or software download etc.
Save.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
44
SELECTING THE PROGRAMME TABLE
You can check which programmes are stored in the memory by displaying the programme table.
Displayed when the
Locked Programme.
Displaying programme LIST
1
LIST
A
have been set up to be skipped by auto
programming or in the programme edit mode.
• Some programmes with the channel number
shown in the programme LIST indicate there is
no station name assigned.
Selecting a programme in the programme list
1
TV/RADIO
Select a programme.
2
OK
A
display the PROGRAMME LIST.
• You may find some blue programmes. These
From the programme you are currently watching, the mode will change
from TV to DTV to Radio.
WATCHING TV / PROGRAMME CONTROL
A
Switch to the chosen programme number.
Displaying the favourite programme table
1
FAV
Display the Favourite Programme table.
45
WATCHING TV / PROGRAMME CONTROL
INPUT LABEL
Selects a label for each input source.
WATCHING TV / PROGRAMME CONTROL
OPTION
Move
OPTION
OK
Menu Language : English
Audio Language : English
Subtitle Language : English
Hard of Hearing( ) Off
Country
:UK
Input
Input Label
Label
Key Lock
: Off
Set ID
:1
Menu Language : English
Audio Language : English
Subtitle Language : English
Hard of Hearing( ) Off
Country
:UK
Input
Input Label
Label
Key Lock
: Off
Set ID
:1
E
1MENU
Move
E
OK
AV1
AV2
Component
RGB
HDMI1
HDMI2
Close
Select OPTION.
2
Select Input Label.
OK
3
OK
Select the source.
4
Select the label.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
46
EPG (ELECTRONIC PROGRAMME GUIDE)
(IN DIGITAL MODE)
This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options.
The EPG supplies information such as programme listings, start and end times for all available services. In addition,
detailed information about the programme is often available in the EPG (the availability and amount of these programme details will vary, depending on the particular broadcaster).
This function can be used only when the EPG information is broadcasted by broadcasting companies.
The EPG displays the programme description for next 8 days.
Switch on/off EPG
1 GUIDE
Programme Guide
1 YLE TV1
1
2
4
5
6
8
06 Mar. 2006 15:09
D
06 Mar.
14:00
15:00
YLE TV1
No Information
Kungskonsumente
YLE TV2
No Information
TV2: Farmen No Information
TV..
No Information
YLE FST
No Information
CNN
No Information
YLE24
... ... No Information ... ...
Tänään otsikoissa
E
TV/RAD Radio
FAV Favourite
Mode
INFO
Inforrmation
Date
Select a programme
1
or
P
Select desired programme.
2
OK
Display the selected programme.
Pr. Change
EPG (ELECTRONIC PROGRAMME GUIDE)
ALL
Switch on or off EPG.
Button Function in NOW/NEXT Guide Mode
RED
OK
Change EPG mode.
Change to the selected programme.
Select NOW or NEXT Programme.
PR
P
GUIDE
TV/RADIO
INFO i
Select the Broadcast Programme.
Page Up/Down.
or
EXIT
Switch off EPG.
Select TV or RADIO Programme.
The detail information on or off.
47
EPG (ELECTRONIC PROGRAMME GUIDE)
(IN DIGITAL MODE)
Button Function in 8 Day Guide Mode
RED
GREEN
Change EPG mode.
Select the Broadcast Programme.
Enter Date setting mode.
PR
P
GUIDE
OK
EPG (ELECTRONIC PROGRAMME GUIDE)
48
Change to the selected programme.
Select NOW or NEXT Programme.
Page Up/Down.
or
TV/RADIO
EXIT
Switch off EPG.
Select TV or RADIO Programme.
INFO i
The detail information on or off.
Button Function in Date Change Mode
GREEN
Switch off Date setting mode.
OK
Change to the selected date.
Select a date.
Switch off Date setting mode.
GUIDE
or
EXIT
Switch off EPG.
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO) CONTROL
You can watch the screen in various picture formats; 16:9, Just Scan, Original, 4:3, 14:9 and Zoom1/2.
If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the
screen and remain visible.
You can adjust the enlarge proportion using DE button.
This function works in the following signal.
PICTURE CONTROL
1
Press the RATIO button repeatedly to select the desired
picture format.
You can also adjust Aspect Ratio in the PICTURE menu.
• 16:9
The following selection will allow you to
adjust the picture horizontally, in linear
proportion, to fill the entire screen(useful for
viewing 4:3 formatted DVDs).
• 4:3
The following selection will allow you to view
a picture with an original 4:3 aspect ratio,
grey bars will appear on both the left and
right of the screen.
49
PICTURE CONTROL
• Original
When your TV receives a wide screen signal it
will automatically change to the picture
format broadcast.
• Zoom2
Choose Zoom 2 when you wish the picture to
be altered, both horizontally extended and
vertically cropped. The picture adopting a
compromise between alteration and screen
coverage.
Original
PICTURE CONTROL
• 14:9
You can view a picture format of 14:9 or a
general TV programme in the 14:9 mode. The
14:9 screen is viewed in the same way as in
4:3, but is magnified to the left and right.
• Just Scan
Following Selection will lead to you view the
picture of best quality without loss of original
picture in high resolution image.
Note: If there are interference in original picture, you can view interference at the edge.
Just Scan
• Zoom1
The following selection will allow you to view
the picture without any alteration, while filling
the entire screen. However, the top and
bottom of the picture will be cropped.
! NOTE
G
G
G
G
50
You can only select 16:9 (Wide), Original, 4:3, 14:9, Zoom 1/2 in Component (under 720p) mode.
You can only select 4:3, 16:9 (Wide) in RGB/HDMI[PC] mode only.
In HDMI/Component (over 720p) mode, Just Scan is available.
You can only select Original in UK digital teletext (MHEG-5).
PRESET PICTURE SETTINGS
Picture Mode-Preset
PICTURE
Move
100
100
50
70
70
0
R
G
E
1MENU
Move
Aspect Ratio : 16:9
Picture
PictureMode
Mode :: Vivid
Vivid
• Backlight
• Contrast
• Brightness
• Sharpness
• Colour
• Tint
100
100
50
70
70
0
OK
Vivid
Vivid
Standard
Cinema
Sport
Game
E
PICTURE CONTROL
Aspect Ratio : 16:9
Picture
PictureMode
Mode :: Vivid
Vivid
• Backlight
• Contrast
• Brightness
• Sharpness
• Colour
• Tint
PICTURE
OK
• Picture Mode adjusts the TV for the best pic-
Select PICTURE.
ture appearance. Select the preset value in the
Picture Mode menu based on the programme
category.
2
OK
Select Picture Mode.
OK
Select desired picture value.
3
4
OK
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
51
PICTURE CONTROL
Auto Colour Tone Control (Warm/Medium/Cool)
Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red, or set to
cool to see less intense colours with more blue.
PICTURE
Move
PICTURE
OK
D
PICTURE CONTROL
Picture Mode : Vivid
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
R
G
E
1MENU
Move
D
Picture Mode : Vivid
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
OK
Colour Temperature
F
Fresh Contrast
High
Fresh Colour
High
Noise Reduction
Medium
Gamma
Medium
Black Level
High
Eye Care
Off
Film Mode
Off
E
Close
Select PICTURE.
2
OK
Select Advanced Control.
OK
Select Colour Temperature.
3
4
Select either Cool, Medium or Warm.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
52
Cool
G
MANUAL PICTURE ADJUSTMENT
Picture Mode-User option
PICTURE
Move
100
70
50
50
50
0
R
G
Aspect Ratio : 16:9
Picture
PictureMode
Mode :: Vivid
Standard (User)
• Backlight
• Contrast
• Brightness
• Sharpness
• Colour
• Tint
E
1MENU
Move
100
70
50
50
50
0
OK
Vivid
Standard
Cinema
Standard (User)
Sport
Game
E
PICTURE CONTROL
Aspect Ratio : 16:9
Picture
PictureMode
Mode :: Vivid
Standard (User)
• Backlight
• Contrast
• Brightness
• Sharpness
• Colour
• Tint
PICTURE
OK
Select PICTURE.
2
OK
Select Picture Mode.
OK
Select desired picture value.
OK
Select Backlight, Contrast, Brightness, Sharpness, Clolour or Tint.
OK
Make appropriate adjustments.
3
4
5
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
! NOTE
G
You can not adjust colour, sharpness and tint in the RGB-PC mode.
53
PICTURE CONTROL
PICTURE IMPROVEMENT TECHNOLOGY
Fresh Contrast
Optimizes the contrast automatically according to the brightness of the reflection.
Fresh Colour
Adjusts the colour of the reflection automatically to reproduce as close as possible natural colours.
Noise Reduction
Removes interference up to the point where it does not damage the original picture.
Gamma
High gamma values display whitish images and low gamma values display high contrast images.
PICTURE CONTROL
PICTURE
Move
PICTURE
OK
D
Picture Mode : Vivid
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
R
G
E
1MENU
Move
D
Picture Mode : Vivid
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
OK
Colour Temperature
Fresh Contrast
Cool
F
Fresh Colour
High
Noise Reduction
Medium
Gamma
Medium
Black Level
High
Eye Care
Off
Film Mode
Off
E
Close
Select PICTURE.
2
OK
Select Advanced Control.
OK
Select Fresh Contrast, Fresh Colour, Noise Reduction or Gamma.
3
4
Select your desired Source.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
54
High
G
ADVANCED - FILM MODE
To set the TV up for the best picture quality for viewing films.
This feature operates only in TV, AV and Component 480i/576i/1080i mode.
PICTURE
Move
PICTURE
OK
D
R
G
E
1MENU
Picture Mode : Vivid
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
OK
Colour Temperature
Cool
Fresh Contrast
High
Fresh Colour
Noise Reduction
Gamma
Black Level
Eye Care
Film Mode
E
High
Cool
Medium
F
High
Medium
High
High
Medium
Off
Medium
F
G
Off
High
Close Off
PICTURE CONTROL
Picture Mode : Vivid
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
Move
D
Select PICTURE.
2
OK
Select Advanced Control.
OK
Select Film Mode.
3
4
Select On or Off.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
55
PICTURE CONTROL
ADVANCED - BLACK(DARKNESS) LEVEL
When you view a film this function adjusts the TV to best picture quality.
This function works in the following mode: AV (NTSC-M), HDMI or Component.
PICTURE
Move
PICTURE
OK
D
PICTURE CONTROL
Picture Mode : Vivid
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
R
G
Picture Mode : Vivid
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
E
1MENU
Move
D
OK
Colour Temperature
Cool
Fresh Contrast
High
Fresh Colour
High
Noise Reduction
Medium
Gamma
Black Level
Medium
F
High
Eye Care
Off
Film Mode
Off
E
G
Close
• L o w : The reflection of the screen gets darker.
• H i g h : The reflection of the screen gets
Select PICTURE.
brighter.
2
• A u t o : Realizing the black level of the screen
OK
Select Advanced Control.
OK
Select Black Level.
and set it to High or Low automatically.
3
4
Select Low or High.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
56
EYE CARE
It helps you adjust brightness to prevent dazzling when the screen is too bright.
PICTURE
Move
PICTURE
OK
D
R
G
E
1MENU
Picture Mode : Standard
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
OK
Colour Temperature
Cool
Fresh Contrast
High
Fresh Colour
High
Noise Reduction
Medium
Gamma
Medium
Black Level
Eye Care
High
F
Film Mode
E
Off
Off
Close
G
PICTURE CONTROL
Picture Mode : Standard
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
Control
Move
D
Select PICTURE.
2
OK
Select Advanced Control.
OK
Select Eye Care.
3
4
Select On or Off.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
57
PICTURE CONTROL
PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
PICTURE
Move
PICTURE
OK
D
PICTURE CONTROL
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
70
• Colour
70
• Tint
0
• Advanced Control
• Picture Reset
1MENU
Move
OK
D
R
G
• Backlight
100
• Contrast
100
• Brightness
50
•i Sharpness
70
Resetting video configuration...
• Colour
70
R
• Tint
0
• Advanced Control
• Picture Reset
G
Select PICTURE.
2
OK
Select Picture Reset.
3
OK
Initialize the adjusted value.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
58
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER
AVL automatically remains on the same level of volume if you change programmes.
Move
Auto
: Off
AutoVolume
Volume : Off
Balance
Sound Mode
: Standard
• 120Hz
• 200Hz
• 500Hz
• 1.2KHz
• 3KHz
0
L
R
0
0
0
0
0
-
+
-
+
-
+
-
+
-
+
E
1MENU
AUDIO
OK
Move
Auto
: Off
AutoVolume
Volume : Off
Balance
Sound Mode
: Standard
• 120Hz
• 200Hz
• 500Hz
• 1.2KHz
• 3KHz
OK
0
L
Off
Off
On
R
0
0
0
0
0
-
+
-
+
-
+
-
+
-
+
PICTURE CONTROL
AUDIO
E
Select AUDIO.
2
OK
Select Auto Volume.
3
OK
Select On or Off.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
59
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS-SOUND MODE
You can select your preferred sound setting; SRS TruSurround XT or Clear Voice, Standard, Music, Cinema,
Sport or Game and you can also adjust the frequency of the equalizer.
Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound
options based on the programme content.
SRS TruSurround XT or Clear Voice, Standard, Music, Cinema, Sport and Game are preset for optimum sound
quality at the factory.
AUDIO
SOUND & LANGUAGE CONTROL
Auto Volume
Balance
Sound
SoundMode
Mode
Move
AUDIO
OK
: Off
Standard
: :Standard
• 120Hz
• 200Hz
• 500Hz
• 1.2KHz
• 3KHz
0
L
R
0
0
0
0
0
-
+
-
+
-
+
-
+
-
+
Auto Volume
Balance
SoundMode
Mode
Sound
Move
: Off
0
: :Standard
Standard
• 120Hz
• 200Hz
• 500Hz
• 1.2KHz
• 3KHz
E
1MENU
OK
0
0
0
0
0
SRS TruSurround XT
Clear Voice
Standard
Standard R
L
Music
Cinema
Sport
Game
E
• If you select C l e a r V o i c e, S R S
Select AUDIO.
T r u S u r r o u n d X T feature will not work.
2
OK
3
OK
Select Sound Mode.
Select SRS TruSurround XT or Clear Voice , Standard, Music,
Cinema, Sport or Game.
• Press the MENU or EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
G
G
60
are a trademark of SRS Labs, Inc.
TruSurround XT and TruSurround HD technology is incorporated under license from SRS Labs, Inc.
SOUND SETTING ADJUSTMENT -USER MODE
Adjusting the audio equalizer.
AUDIO
OK
: Off
0
R
-
+
-
+
-
+
-
+
-
+
E
1MENU
Auto Volume
Balance
SoundMode
Mode
Sound
: Off • 120Hz
• 200Hz 0
: :Standard
(User)
Standard
• 500Hz
• 120Hz
• 1.2KHz 0
• 200Hz
0
• 3KHz
• 500Hz
• 7.5KHz 0
• 1.2KHz
0
• 12KHz
• 3KHz
0
E
00
0
0
0L
0
0
0
OK
-
+
-
+
-
+
R
+
-
+
-
+
Close
Select AUDIO.
2
OK
3
OK
+
-
Select Sound Mode.
Select SRS TruSurround XT or Clear Voice, Standard, Music, Cinema, Sport or
Game.
SOUND & LANGUAGE CONTROL
: :Standa
Download PDF