LG | MT-60PZ11 | LG MT-60PZ11 Owner’s Manual

Please read this owner's manual
operating
carefully
before
the Monitor.
Retain it for future reference.
Record model number and serial number of the
Monitor.
See the label attached
on
the back of the Monitor
and
quote this information to your dealer when you
require service.
Model number
Serial number
:
:
PLASMONITR
MT-60PZ11/B/G/K/S
MZ-60PZ13/B/G/K/S
OWNER'S MANUAL
INPUT
ON/OFF
SELECT
VOLUME
What is
If
voltage
a
is
Plasma
Display
?
inputted to gas in glass panels, ultraviolet rays is outputted and fused with a
light is emitted. A Plasma Display is a next generation flat Display using
At this moment,
160°
Wide
-
A Plasma
phenomenon.
of vision
angle range
Display provides
fluorescent substance.
this
than 160°
more
angle
range of vision
so
that you
get
can
a
picture
without dis-
tortion from any direction.
Easy
installation
A Plasma
Display is much lighter and
Display at the desired place.
Plasma
Big
The
smaller than other
same
class
products
so
that you
install the
can
screen
screen
of
a
Plasma
Display
Multimedia Plasma
A Plasma
Display
The
can
get vivid experience
as
if you
are
in
a
theater.
Display
a
computer
so
that you
about coloured dots may be
The PDP which is the
can occur
that you
can use
it
as a screen
for conference,
so on.
explanation
defects
so
be connected with
can
game, internet and
is 60"
display
device of this
product
is
present
composed
on
PDP
screen
of 0.9 to 2.2 million cells and
in the manufacture of the PDP. Several coloured dots visible
on
the
screen
a
few cell
would be
mean that the PDP is faulty. We hope you
product which corresponds to this standard is regarded as acceptable. It means
that it could not be changed or refunded.
We promise that we'll do our best to develop our technology to minimize the cell defects.
acceptable,
in line with other PDP manufacturers and would not
will understand that the
The
about noise of 60" PDP
explanation
In the
a PC to keep the CPU cool, the PDP is equipped with cooling fans to
product. Therefore, a certain level of noise could occur when the fan is operated. This noise doesn't have any negative effect on its efficiency and liability and it's also determined to
have no difficulty while using this product. The noise from the fans is normal in the operation of this product. We hope you will understand that a certain level of noise is acceptable. It means that it is not changesame
way that
improve
the
able
refundable.
nor
a
reliability
fan is used in
of this
WARNING
This is Class A
in which
case
product.
the
user
In
a
domestic environment this
may be
required
to take
product may
adequate measures.
cause
radio interference
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
ONOFF
INPUT
SELECT
VOLUME
Contents
First step
Safety Instructions ....................................................4
Monitor Overview
Controls of the Monitor .............................................8
Controls of the remote control ................................12
Monitor Installation .................................................14
Equipment Connections and Setup
Watching VCR ........................................................16
Watching Cable TV.................................................17
Watching external AV source..................................18
Watching DVD ........................................................19
Connecting PC .......................................................20
Function checking in PC mode ..............................22
Adjusting in PC mode .............................................23
PIP function ............................................................26
Twin picture mode ..................................................29
Using
the remote control ........................................31
Basic Features Setup and Operation
Turning on the Monitor ...........................................32
Selecting the on screen language ..........................33
Function checking...................................................34
Sleep Timer
Setting Sleep
Timer
(Monitor
turn-off
time)
............35
Picture & Sound
Auto picture control ................................................36
Adjusting picture condition .....................................37
DRP (Digital Reality Picture) ..................................38
Selecting menu options ..........................................39
Adjusting Sound: Bass, Treble, Balance ................40
Auto sound control .................................................41
AVL (Auto volume leveler) ......................................42
Special Features
Using Still function ..................................................43
Adjusting OSD Transparency .................................44
Setting picture format .............................................45
External control device setup .................................46
Others
Troubleshooting check list ......................................54
Product specifications.............................................55
Safety
-
Instructions
It is recommended that this product only be used at an altitude of less than
6562 feet (2000m) to get the best quality picture and sound.
WARNING
Indorstali
NOTES
Do not place the Monitor in
direct sunlight or near heat
sources such as heat registers,
stove and so on.
This may
-
cause a
This plasma
be mounted
display is designed
horizontally (wide
to
viewing).
fire.
WARNING
Do not
the Monitor in
such as a bathany place where it
use
damp place
room or
OutdorInsali
is
likely
to
get
wet.
Bend antenna cable between
inside and outside building to prevent rain from flowing in.
-
This may cause a fire or could
give an electric shock.
-
WARNING
NOTES
Earth wire should be connected.
-
-
Power
-
If the earth wire is not connected,
there is possible a danger of electric
shock caused by the current leakage.
If grounding methods are not possible, a separate circuit breaker should
be employed and installed by a qualified electrician.
Do not connect ground to telephone
wires, lightning rods or gas pipe.
Short-circuit
breaker
4
This may cause water damaged inside
the Monitor and could give an electric
shock.
Never touch the power
with a wet hand
-
This may
cause an
plug
electric shock.
*
Safety
instructions have two kinds of
WARNING
NOTES
information, and each meaning of it is
below.
as
The violation of this instruction may
cause
serious
The violation of this instruction may
cause
light injuries
injuries
or
and
even
damage
death.
of the
product.
Take
care
of
danger that may happen
under
specific condition.
NOTES
Disconnect from the mains
and remove all connections
before moving.
Do not place the Monitor in
built-in installation such as
a bookcase or rack.
a
-
Ventilation
required.
When
installing
the Monitor
on a
table, be careful not to place the
edge
-
of its stand.
This may cause the Monitor to fall,
causing serious injury to a child or
adult, and serious damage to the
Monitor.
NOTES
Do not place an outside antenna in
the vicinity of overhead power lines
other electric light or power circuits.
-
This may
cause an
electric shock.
or
There should be enough distance between an
outside antenna and power lines to keep the former from touching the latter even when the
antenna falls.
-
This may cause
an electric shock.
NOTES
Do not pull the cord but the
when unplugging.
plug
-
This may
cause a
fire.
Ensure the power cord
doesn't trail across any hot
objects like a heater.
-
This may cause
tric shock.
a
fire
or an
elec-
Do not plug when the power
cord or the plug is damaged
or the connecting part of the
power outlet is loose.
-
This may cause a fire
an electric shock.
or
FirstepMonvwCcBaSlmPu&df
Others
5
Safety
Instructions
WARNING
WARNING
Do not placing anything containing liquid
on
-
Using
top of the Monitor.
This may cause a fire
could give an electric
shock.
or
Do not insert any
into the
exhaust vent.
Do not
object
-
place heavy
objects
on
the
Monitor.
This may cause a fire
could give an electric
shock.
or
-
This may
injury
to
a
cause
child
serious
adult.
or
WARNING
Do not use water the Monitor
while cleaning.
-
Cleanig
This may cause damaged the
Monitor or could give an electric
shock.
In case of smoke or strange
smell from the Monitor, switch it
off ,unplug it from the wall outlet
and contact your dealer or service center.
-
This may cause a fire
an electric shock.
or
could
give
WARNING
Do not attempt to service
the Monitor yourself.
Contact your dealer or service center.
Others
6
-
This may cause damaged the
Monitor or could give an electric
shock.
During
unplug
a
lightning thunder,
the Monitor from the
wall outlet and don't touch an
antenna cable.
-
This may cause damaged the
Monitor or could give an
electric shock.
WARNING in U.K.
*
This set is
only
with a BS 1363 approved 13 amp mains plug, fused at 13 amp. When replacing the fuse
always use a 13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To
obtain a replacement fuse cover contact your dealer or "LG Electronics U.K. Ltd." If the type of plug supplied is
not suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted.
A mains plug removed from the mains lead of this set must be destroyed. A mains plug with bared wires is
hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or
with the earth symbol
or coloured green or green and yellow. If any other plug is fitted, use a 13 amp fuse,
either in the plug, or at the distribution board.
The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or coloured red.
supplied
NOTES
NOTES
Dispose of used batteries
carefully to protect a child
from eating them.
-
In
case
to
see a
When moving the Monitor
assembled with speakers do
not carry holding the speak-
Avoid having a fixed image
remain on the screen for a
long period of time. Typically
a frozen still picture from a
VCR, 4:3 picture format or if
a CH label is present; the
fixed image may remain
visible on the screen.
ers.
that it eats them, take it
doctor immediately.
-
This may
cause
the Monitor to
fall, causing serious injury
child or adult, and
to
a
serious
damage
to the
Monitor.
NOTES
Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners
or aerosol cleaners.
-
This may cause damaged the Monitor
an electric shock.
or
could
Contact the service center once a year to
clean the internal part of the Monitor.
-
Accumulated dust
can cause
mechanical failure.
give
NOTES
The distance between eyes
and the screen should be
about5~7timesaslongas
diagonal length of the
screen.
-
If not, eyes will strain.
Unplug the Monitor from the
wall outlet when it is left
unattended and unused for
long periods of time.
-
Accumulated dust may cause
fire or an electric shock from
deterioration or
electric leakage.
a
Only
use
teries.
-
the
specified
bat-
This make cause damaged the
Monitor or could give an electric
shock.
FirstepMonvwCcBaSlmPu&df
Others
7
Controls of the Monitor
<Front Panel Controls>
ON/OFF
INPUT
ON/OFF
SELECT
VOLUME
Main power button
Power standby indicator
Illuminates red in standby
mode Illuminates green
when the Monitor is turned
INPUT
SELECT
VOLUME
on
INPUT SELECT button
Sub power button
VOLUME (Φ,Γ) buttons
8
Remote control
sensor
<Back Panel>
R AUDIO L (MONO) VIDEO
AV INPUT
RL
AUDIO
(MONO) VIDEO
AV INPUT
S-VIDEO
Y
PB
Y
S-VIDEO
PB
PR
COMPONENT(480i/480p)
(DVD INPUT)
PR
COMPONENTI(480i/480p)
(DVD INPUT)
R
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
(+)
AUDIO L
AUDIO INPUT
RS-232C
R
()
()
L
EXTERNAL SPEAKER
(+)
(8Ω)
(+) R ()
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
AUDIO INPUT
AV INPUT /
AC INPUT
RS-232C
() L (+)
EXTERNAL SPEAKER 8Ω
EXTERNAL SPEAKER
(8 ohm output)
COMPONENT (480i/480p)
(DVD INPUT) SOCKETS
Γ The Interface board
(AP-60EA21) is not equipped on MZ60PZ13 series models. Contact your
dealer for buying this optional item.
RGB-PC INPUT
AUDIO INPUT/
RS-232C jacks
(VGA/SVGA/XGA/SXGA)/
AC INPUT
POWER INPUT
SOCKET
This Monitor operates
on an AC mains supply,
the voltage is as indicated as inside back cover
of this manual. Never
apply DC power to the
Monitor.
FirstepMonvwCcBaSlmPu&df
Others
9
Accessories
POWER
SLEEP
INPUT SELECT
PSM
SSM
ARC
STILL
PIP
/TWINPICTURE
PIPINPUT
POSITION
MENU
VOL
POWER
REW
MUTE
OK
STOP
PLAY
VOL
P/STLL
FF
REC
D-sub 15
pin
cable
Power cord
Remote control handset
1.5V
LG TV
1.5V
AS
mark
Owner's Manual
Alkaline batteries
(Optional)
Optional
-
-
Extras
Optional extras can be changed or modified
optional extras can be added.
Contract your dealer for buying these items.
for
quality improvement
without any notification
PR
PB
Y
VIDEO
(MONO)
AUDIO
RL
INPUT
(480i/480p)
COMPONENT
(DVD INPUT)
S-VIDEO
AV
AP-60EA21
AP-60WA20M series
(Tilt
10
wall
mounting bracket)
(interface board)
AP-60WA10 series
(Wall mounting bracket)
new
Optional
-
-
Extras
Optional extras can be changed or modified
optional extras can be added.
Contract your dealer for buying these items.
for
quality improvement
without any notification
AP-60CA10 series
AP-60FA10 series
(Ceiling mounting bracket)
(Floor type stand)
AP-60DA10 series
AP-60SA10 series
(Desktop stand)
(Speakers)
AP-60SA10D series
AP-60SA10F series
(Speaker stand)
(Floor type speaker stand)
new
FirstepMonvwCcBaSlmPu&df
Others
Video cables
Audio cables
11
Controls of the remote control
-
When
using
the remote control aim it at the remote control
sensor
of the Monitor.
POWER
POWER
SLEEP
SLEEP (Refer to
p.35)
PSM (Refer to
p.36)
ARC (Refer to
p.45)
INPUT SELECT
PSM
SSM
ARC
STILL
PIP
PIP
(Refer
to
/ TWIN PICTURE
p.26)
PIP INPUT
PIP INPUT
(Refer
to
POSITION
p.27, 30)
MENU
MUTE
MENU
OK
OK
VOL
POWER
STOP
P/STILL
REW
PLAY
FF
VOL
VOLUME (Φ, Γ)
VCR BUTTONS
controls
a
LG video cassette
recorder.
12
REC
INPUT SELECT button
INPUT SELECT
SSM (Refer to
on
the
remote control
p.41)
Each press of this button
the mode
STILL (Refer to
p.43)
TWIN PICTURE
(Refer
POSITION (Refer to
to
p.29)
as
changes
shown below.
Video
S-Video
RGB
Component
p.27)
MUTE
switches the sound
on or
off.
Video, S-Video, Component
These modes
are
Interface board
(not supplied)
is
installed.
Δ/Ε
selects
:
selected when the
a menu
item.
Γ The Interface board
(AP-60EA21)
is not
equipped
on
MZ-60PZ13 series models.
FirstepMonvwCcBaSlmPu&df
Others
13
Monitor Installation
-
The Monitor
can
desktop type,
be installed in various ways such
as
wall
mounting type,
etc..
Wall Mount Installation
?
The monitor
can
be installed
(For further information,
Guide'.)
on
refer to
the wall
'(Tilt)
the picture above.
mounting bracket Installation
as
wall
and
Setup
Tips
?
Install this monitor
only
in
a
location where
adequate
ventilation is available.
a.
4inch
mount minimum allowable
clearances for adequate
(Wall
1.18inch
ventilation)
4inch
4inch
4inch
14
Desktop pedestal installation
INPUT
ON/OFF
?
The Monitor
(For
can
be installed
SELECT
on a
further information, refer to
desk
as
'Desktop
VOLUME
shown above.
stand Installation and
Setup Guide'.)
b.
(Pedestal
mount minimum
4inch
1.18inch
allowable clearances for
adequate ventilation)
4inch
4inch
FirstepMonvwCcBaSlmPu&df
Others
2.36inch
15
Watching VCR
-
When
(Video
-
-
-
-
connecting the Plasma Monitor with external equipments, match the colours of connecting ports
yellow, Audio(L) white, Audio(R) -red).
have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the
-
-
If you
Plasma Monitor.
If you connect an S-VIDEO VCR to the S-VIDEO
input, the picture quality is improved; compared to
connecting a regular VCR to the Video input.
If 4:3 picture format or still word such as watching VCR or CH label is on the screen for a long time,
that fixed image may remain visible.
Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR, 4:3 picture format or if a CH label is present;
the fixed image may remain visible on the screen.
R AUDIO
L(MONO)VDEO
AV INPUT
Y
R AUDIO L (MONO) VIDEO
AV INPUT
S-VIDEO
PB
Y
S-VIDEO
PR
PB
P R
COMPONENT(480i/480p)
(DVD INPUT)
(+)
R AUDIO L
RGB-PC INPUT
(VGA/SVGAXGA/SXGA)
AUDIO INPUT
RS-232C
R
)
()
L
(+)
EXTERNALSPEAKER
(8Ω)
ACINPUT
(+)
R AUDIO L
RGB-PC INPUT
COMPONENT(480i/480p)
(DVD INPUT)
(VGA/SVGA/XGA/SXGA)
AUDIO INPUT
RS-232C
R
()
()
EXTERNAL
<Back
panel
L
(+)
SPEAKER(8Ω)
AC INPUT
of the Monitor>
To watch VCR
S-VIDEO
(When the Interface board is installed.)
OUT
(R)
AUDIO
(L)
Γ The Interface board
VIDEO
panel
is not
equipped
Press INPUT SELECT button
INPUT SELECT
<Back
(AP-60EA21)
on
MZ-60PZ13 series models.
IN
of VCR>
on
the
remote control and select Video.
1Insert
(When connecting with S-Video,
S-Video.)
select the
2
a video tape into the VCR and
press the PLAY button on the VCR.
See VCR owner's manual.
Tips
?
16
To avoid picture noise
and monitor.
(interference),
leave
an
adequate
distance between the VCR
Watching Cable
-
After
you
to a cable TV service from
watch cable TV programming.
subscribing
can
R
AUDIO
L
(MONO)VIDEO
AV INPUT
S-VIDEO
Y
PB
P R
(DVD INPUT)
Y
R AUDIO L (MONO) VIDEO
AV INPUT
S-VIDEO
PB
R
COMPONENT(480i/480p)
RGB-PC NPUT
a
local
R
(+)
AUDIO L
AUDIO INPUT
EXT
RS-232C
(VGA/SVGA/XGASXGA)
PR
TV
()
RNALSPEA
L
R
provider
R
B-PC INPUT
(8Ω)
(
RS-232C
(VGA/ VGA/XGA/SXGA)
AUDIO
a
converter,
AC INPUT
(+)
AUDIO INPUT
<Back
installing
(+)
R AUDIO L
COMPONENT(480i/480p)
(DVD INPUT)
and
panel
R
()
()
EXTERNAL
L
(+)
SPEAKER(8Ω)
AC INPUT
of the Monitor>
<Cable box>
VO
TV
VCR
RF
To watch cable TV
Γ The Interface board
(AP-60EA21)
is not
1
(When the Interface board is installed.)
equipped
Press INPUT SELECT button
Cable
on
on
MZ-60PZ13 series models.
the
INPUT SELECT
remote control and select Video.
Tune to cable service
2
provided
channels
using
the cable box.
Others
Tips
?
For further information regarding cable TV service, contact your local
cable TV service provider(s).
FirstepMonvwCcBaSlmPu&df
17
external AV
Watching
-
When
connecting
the Plasma Monitor with external
match the colours of
AUDIO
L
(MONO)VIDEO
AV INPUT
AV INPUT
S-VIDEO
Y
PB
panel
Y
S-VDEO
PB
PR
COMPONENT(480i/480p)
(DVD NPUT)
R
RGB-PC INPUT
AUDIO
R
(+)
L
AUDIOINPUT
RS-232C
(VGA/SVGAXGA/SXGA)
PR
EXT
()
RNALSPEA
L
R
+)
(8Ω)
AC NPUT
(+)
R AUDIO L
RGB
COMPONENT(480i/480p)
PC INPUT
(VGA/S
(DVD INPUT)
<Back
equipments,
connecting ports.
R
RL
AUDIO
(MONO) VIDEO
source
GA/XGA/SXGA)
AUDIO INPUT
RS-232C
R
()
()
EXTERNAL
L
(+)
SPEAKER(8Ω)
AC INPUT
of the Monitor>
Camcorder
R
AUDIO
L
VIDEO
Video game set
To watch external AV
Γ The Interface board
1
2
18
(AP-60EA21)
is not
equipped
Press INPUT SELECT button
on
source (When
on
MZ-60PZ13 series models.
the
remote control of the monitor to select
Video.
Operate
the
corresponding
external
the Interface board is
equipment.
INPUT SELECT
installed.)
DVD
Watching
How to connect (When
Γ The Interface board
?
(AP-60EA21)
is not
the Interface board is
equipped
on
MZ-60PZ13 series models.
Connect DVD video inputs to Y, PB, PR of COMPONENT
audio inputs to Audio sockets of AV INPUT.
R
AUDIO
L
(MONO)VIDEO
AV INPUT
Y
R AUDIO L (MONO) VIDEO
AV INPUT
S-VIDEO
PB
Y
S-VIDEO
PB
P R
COMPONENT(480i/480p)
(DVD INPUT)
R
RGB-PC INPUT
R
(+)
AUDIO L
AUDO INPUT
RS-232C
(VGA/SVGA/XGA/SXGA)
PR
COMPONENT(480i/480p)
(DVD INPUT)
installed.)
EXT
()
RNALSPEA
L
R
(+)
(8Ω)
AC INPUT
RS-232C
AUDIO INPUT
Back
<
<
How to
(When
AUDIO
Back
(L)
B
panel
of
a
DVD
use
Γ The Interface board
(AP-60EA21)
installed.)
is not
equipped
on
()
panel
L
(+)
SPEAKER(8Ω)
AC INPUT
of the Monitor>
R
player>
?
the Interface board is
()
EXTERNAL
(VGA/SVGA/XGA/SX A)
(R)
R
(+)
R AUDIO L
RGB-PC INPUT
and
(480i/480p) (DVD INPUT)
Component Input ports
can get better picture quality if you
connect DVD player with component input
You
ports
as
below.
MZ-60PZ13 series models.
Component ports
?
?
Press INPUT SELECT button on the remote control of the
monitor to select Component.
Try this after turning on the DVD player.
of the
Monitor
Video
output ports
of DVD
player
YPBPR
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
19
FirstepMonvwCcBaSlmPu&df
Others
Connecting
-
-
PC
a
Control Source
Computer
You can easily connect the Plasma Display to your PC for outstanding image and sound.
Use the Monitor to display images and sound from a PC Computer source.
Setup
?
Instructions to Connect
PC to your Monitor
a
If the
image output of the PC is set higher than
no picture will appear on the Monitor.
(UXGA is not supported.)
Connect the signal cable from the monitor Output
Default monitor.
UXGA,
?
port
on
not be used for
the Monitor.
quality picture. (Look
not
are
supplied
To set up the Monitor to operate within a PC windows environment, select Normal, Standard or
R AUDIO L
Y
Back
How to
panel
PB
VIDEO
Y
(MNO)
AVINPUT
S-VDEO
PB
PR
COMPONENT(480i480p)
(DVD NPUT)
PR
COMPONENT(480i/480p)
(DVD INPUT)
R
RGB
PC
T
(VGA/SVGA/
R
(+)
R AUDO L
RGBPC NPUT
(VGA/SVGAXGA/SXGA)
AUDIO NPUT
RS-232C
for
a
x
720 to
a
sound card,
EXT
()
RNALSPEA
L
output of the
get the best
video card that
nVIDIA GeForce 2 pro or similar
supports this resolution)
Monitor.)
S-VIDEO
Play
It is recommended that the resolution
?
ports of the Monitor. (Audio cables
AV INPUT
and
adjust
PC should be set to 1280
RAUDIO L (MONO) VIDEO
Plug
If your PC computer is equipped with
the sound output on the PC.
?
Connect the audio cable from the PC to the Audio
with the
?
on
can
functionality.
the PC to the RGB-PC INPUT
(VGA/SVGA/XGA/SXGA) port
?
The Monitor
?
chipset
uses
the
that
(+)
ER
AC NPUT
(8Ω)
(+)
AUDIO
AUD O INPUT
RS-232C
R
()
()
EXTERNAL
SXGA)
L
(+)
AC INPUT
SPEAKER(8Ω)
of the Monitor
use
PC
?
INPUT SELECT
On the remote control
Setup
computer and press the ON/OFF button on the
power to it. Second, turn on the display by pressing
the
button on the Monitor or by pressing the POWER button on
the Monitor's remote control.
Use the INPUT SELECT button on the remote control to select the
RGB input source.
Set the resolution output of the PC to SXGA or under (1280 x 1024,
First,
turn
Monitor to
?
?
on
the PC
apply
75Hz). (Refer
to page
21.)
Tips
?
Avoid
keeping a fixed image on the Monitor's screen
permanently imprinted on the screen; use a
become
?
20
If the resolution
output of the PC computer is
(VGA/SVGA/XGA/SXGA) input port
accordingly.
on
over
for
a
SVGA,
the Monitor.
long period
screen saver
of time. The fixed
when
image
possible.
connect the PC to the RGB-PC
Change
the PC
computer resolution output
may
Monitor
Image Display Specifications
Resolution
Horizontal
Vertical
Frequency (KHz) Frequency (Hz)
640x350
720x400
640x480
800x600
832x624
1024x768
1280x720
1152x864
1152x870
1280x960
1280x1024
31.468
70.09
37.861
85.08
31.469
70.08
37.927
85.03
31.469
59.94
35.000
66.66
37.861
72.80
37.500
75.00
43.269
85.00
45.913
90.03
53.011
100.04
64.062
120.00
35.156
56.25
37.879
60.31
48.077
72.18
46.875
75.00
53.674
85.06
56.000
90.00
64.016
100.00
49.725
74.55
48.363
60.00
56.476
70.06
60.023
75.02
68.677
84.99
52.400
69.98
54.348
60.05
63.995
70.01
67.500
75.00
77.487
85.05
68.681
75.06
60.000
60.00
75.000
75.00
63.981
60.02
79.976
75.02
FirstepMonvwCcBaSlmPu&df
Others
Tips
?
Synchronization input
form
:
separate
21
Function
-
-
Select RGB
input
in PC mode
checking
source.
PIP/DW function is worked when the interface board is installed.
Interface board
(AP-60EA21) is
MENU
not
equipped
on
MZ-60PZ13 series models.
Press the MENU button.
1
2
Press the Δ / Ε button.
?
Each time you press this button you
PSM
Γ
85Γ
Brightness
50Γ
Colour
50Γ
Tint
0Γ
50Γ
Sharpness
OK
ΔΕ Γ
MENU
<Picture
SSM
menu>
Γ
AVL
Γ
Treble
50Γ
Bass
50Γ
Balance
0Γ
OK
Γ
MENU
<Sound
menu>
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
ΔΕ Γ
OK
MENU
<Special
menu>
?
The PIP works in
?
The TWIN PICTURE works in
VGA, SVGA, XGA, 60Hz.
VGA, 60Hz.
Press the Γ button and then press the Δ / Ε
VOL
VOL
223
below.
Γ
DRP
Contrast
ΔΕ
can see menus as
or
Φ / Γ button to select a function you want to use.
?
Press the OK button to exit.
Adjusting
Auto
-
-
-
in PC mode
configure
Select RGB
input source
Automatically adjusts picture position and eliminates any image shaking.
When watching PIP/TWIN PICTURE, Screen option is not available in
menu.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
ΓToSet
VOL
Press the Δ / Ε button to select
Auto-configure and then press
the Γ button.
2
Auto-configure
Γ
ΓToSet
Γ
Γ
Phase
Γ
Reset
Γ
VOL
?
?
If
3
When Auto.configure has finished, "OK" will be shown on screen.
If the position of the image is incorrect, try Auto adjustment again.
needs to be
,and Phase.
picture
Conectis
VOL
Press the Δ / Ε button to select Screen and
then press the Γ button.
1
FirstepMonvw
adjusted
more
after auto
adjustment, adjust
BasicopertnSlmPu&df
Others
Tips
?
If the
image
is still not correct, your Monitor is
functioning properly
but needs further
adjustment. 23
Adjusting
Adjusting
-
and
Only adjust
in PC mode
horizontal / vertical
in
position
component 480i/480p.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
VOL
Press the Δ / Ε button to select Screen and
then press the Γ button.
1
VOL
Press the Δ / Ε button to select
then press the Γ button.
2
or
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
ΓToSet
and
Auto-configure
Γ
Γ
0
Γ
VOL
?
?
3
Select
Select
Γ
Reset
Γ
for vertical position adjustment.
for horizontal position adjustment.
Press the Φ / Γ button to adjust until you get desired horizontal
vertical position and then press the OK button.
?
?
or
The adjustment range of
is -50
+50.
The adjustment range of
is -100
+100.
Based on the input mode, the adjustment range of
or
may change.
Based on the input signal, the position of the picture may not change even
though you have adjusted the horizontal or vertical position with this function.
~
~
?
VOL
24
Phase
VOL
OK
FirstepMonvw
Adjusting phase
-
If the
picture isn't clear after auto adjustment and especially that characters are still
then adjust the picture phase manually.
When watching PIP/TWIN PICTURE, Screen option is not available in Special menu.
trem-
bling,
-
READY
Conectis
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the
(
Γ
MENU
1
button.
)
VOL
Press the Δ / Ε button to select Screen and
then press the Γ button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
BasicopertnSlmPu&df
ΓToSet
VOL
2
Press the Δ / Ε button to select Phase and
then press the Γ button.
Auto-configure
Γ
Γ
Γ
Phase
Reset
VOL
Press the Φ / Γ button to
3
adjust phase
Γ
30
Γ
and then press the OK but-
ton.
?
The
adjustment range
of Phase is 0
63.
~
OK
VOL
VOL
Others
Initializing
?
To initialize the adjusted value, select Reset with the Δ / Ε button and then
press the Γ button.
25
PIP function
-
-
-
-
-
-
-
-
before pressing PIP
only when the interface board is installed.
Interface board (AP-60EA21) is not equipped on MZ-60PZ13 series models.
This function works only in the following resolution;
640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz)
When you select RGB for main picture in PIP/Twin picture, you can watch video, cable TV or DVD
sub picture.
Color of main picture may be different from sub picture's in PIP/Twin picture mode.
If input source for main picture is changed while in PIP/Twin picture mode, sub picture will disappear.
When watching PIP/Twin picture, Screen option is not available in
menu.
With PIP active, not all picture formats can be used for the main/sub picture.
Select RGB
input
source
This function works
Watching
PIP
the PIP
(Picture
in
Press the PIP button.
?
Each time you press PIP
PIP size as below.
PIP
or Φ
/ Γ button, you
PIP [L]
[S]
PIP
Φ
PIP[S]
Γ
<Small PIP>
PIP
Φ
PIP[L]
<Large
PIPΦOff
Γ
PIP>
Γ
<Off>
26
Picture)
can
change
Off
the
for
Selecting
PIP INPUT
the
Press the PIP INPUT button in PIP mode.
?
Each time you press PIP INPUT button, you
S-Video and Component.
Component
PIP
Moving
POSITION
FirstepMonvw
input signal
Input
Φ
source
Video
the Sub
only
toggle Video,
works in 480i mode.
Conectis
Γ
BasicopertnSlmPu&df
picture
Press the POSITION button in PIP mode.
?
Each press of the POSITION button will change the
the sub picture on the screen as shown below.
position
of
Others
27
PIP function
Selecting
-
-
-
-
options
before pressing PIP
only when the interface board is installed.
Interface board (AP-60EA21) is not equipped on MZ-60PZ13 series models.
This function works only in the following resolutions;
640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz)
To use this function, connect PC video port to RGB-PC INPUT(VGA/SVGA/XGA/SXGA)
Select RGB
input
source
This function works
connect PC audio
-
PIP sound
Sound Select is
port
socket and
to AUDIO INPUT.
always
selected
of
Sound[M] regardless
prior
sound choice.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the
(
Γ
MENU
1
)
button.
VOL
Press the Δ / Ε button to select PIP/DW and
then press the Γ button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
VOL
2
Press the Δ / Ε button to select Sound
Select and then press the Γ button.
VOL
3
Press the Δ / Ε button to select Sound [M]
Sound [S] and then press the OK button.
Γ
PIP
Γ
Input
Γ
Sound Select
Γ
Sound
[M]
Position
Γ
Sound
[S]
DW
Γ
PIP
Γ
Input
Γ
Sound Select
Γ
Sound
[M]
Position
Γ
Sound
[S]
or
OK
28
DW
ΓToSet
Twin
-
-
Select RGB
picture
input
mode
FirstepMonvw
source.
This function works
only when the interface board is installed.
(AP-60EA21) is not equipped on MZ-60PZ13 series models.
This function works only in the following resolutions;
640x480 (only in Vertical frequency 60 Hz)
With TWIN PICTURE active, not all picture formats can be used for the main/sub picture.
Interface board
-
-
/ TWIN PICTURE
Conectis
Press the /TWIN PICTURE button.
?
Each time you press /TWIN PICTURE
can select On or Off.
or Φ
Main
/ Γ button, you
picture
Sub
?
DW
ΦOnΓ
<ON>
picture
showing a fixed
image on the screen, sub
picture moves every 2
To avoid
BasicopertnSlmPu&df
hours.
:Center
Downside
?
DW
Center
Sub picture of TWIN PICTURE is always located in
center position at first and
movement of sub picture
operate.
ΦOffΓ
?
<OFF>
Upside
It's not out of order even
a horizontal noise
occur in blanking part of
though
sub
picture.
Others
29
Twin
picture
Selecting
PIP INPUT
mode
a source
picture
Press the PIP INPUT button in TWIN PICTURE mode.
?
Each time you press PIP INPUT button, you
S-Video and Component.
Component
PIP
30
for the Twin
Input
source
Φ
Video
only
Γ
works with 480i
toggle Video,
signal input.
Using
Inserting
the remote control
?
the
Open
battery compartment
cover on
side and insert the batteries with correct
?
Apply
two 1.5V alkaline batteries of AAA
Don't mix the used batteries with
?
Notes for
Make
sure
objects
FirstepMonvw
batteries
using
these
are no
between the
new
Install the batteries with the correct
the back
polarity.
Conectis
type.
batteries.
polarities.
BasicopertnSlmPu&df
the remote control
Don't
place
near a
the remote control
heater
remote control and its
Strong impact
sensor.
trol may
damp place.
or
cause
on
the remote
operation
con-
failure.
Signal
from the remote control
may be disturbed by sun light or
other strong light. In this case,
turn the set to other direction.
Others
31
Turning
-
When
using
Turning
on
control,
aim it at its
the Monitor
just
Connect power cord
1
sensor on
the Monitor
the Monitor.
after installation
correctly.
Press the ON/OFF button on the Monitor. At this moment, the Monitor is
switched to standby mode. Press the
or INPUT SELECT button on the
Monitor or press the POWER or INPUT SELECT button on the remote control
and then the Monitor will be switched on.
2
Turning
1
the remote
on
on
the Monitor
(power
cord is still
If the Monitor is turned off with the
connected)
button
on
the Monitor
Press the
or INPUT SELECT button on the Monitor or press the POWER
INPUT SELECT button on the remote control and then the Monitor will be
switched on.
or
2
3
If the Monitor is turned off with the ON/OFF button
?
Press the ON/OFF button
the Monitor to turn
on
the Monitor
the Monitor.
If the Monitor is turned off with the remote control and also the ON/OFF
button on the Monitor
?
Press the ON/OFF button on the Monitor and then press the
or INPUT
SELECT button on the Monitor or press the POWER or INPUT SELECT button on the remote control and then the Monitor will be switched on.
Tips
Adjusting
Volume(Γ)
?
sound.
32
on
on
volume level
button increases the sound and
volume(Φ)
button decreases the
Selecting
the
on screen
language
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Press the Δ / Ε button to select
Language and then press the Γ button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
VOL
2
3
Press the Δ / Ε button to select the desired
language.
Press the OK button.
OK
FirstepMonvwCcBaSlmPu&df
Others
33
Function
-
Select VIDEO
MENU
input
checking
source.
1
Press the MENU button.
2
Press the Δ / Ε button.
?
Each time you press this button you
shown below.
PSM
Γ
DRP
Γ
Contrast
100
50Γ
Colour
50Γ
Tint
0Γ
50Γ
Sharpness
OK
ΔΕ Γ
MENU
<Picture
SSM
Γ
Treble
50Γ
Bass
50Γ
Balance
0Γ
OK
Γ
MENU
<Sound
Language
Γ
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
OK
MENU
<Special
3
menu>
PresstheΓbuttonandthenpresstheΔ/ΕorΦ/
Γ button to select a function you want to use.
?
34
menu>
ARC
ΔΕ Γ
VOL
menu>
Γ
AVL
VOL
Γ
Brightness
ΔΕ
can see menus
Press the OK button to exit.
Setting sleep time
<
Sleep Timer turns the
SLEEP
Monitor off after
a
preset time.
>
Press the SLEEP button to set sleep time.
Each time you press SLEEP button, the next
preset setting time is changed as shown below.
Φ---Γ
Φ10Γ
Φ20Γ
Φ30Γ
Φ120Γ
Φ90Γ
Φ60Γ
Φ240Γ
Φ180Γ
Φ---Γ
?
To release sleep time setting, press the SLEEP or
Φ / Γ button repeatedly to select Φ
Γ.
1' is displayed, one minute before the Monitor
is due to switch off.
---
'
?
Tips
?
?
?
When the sleep time you want is displayed on the screen, don't press the
SLEEP button. After 20 seconds, the screen display disappears and sleep
time is set.
To check remaining sleep time after setting, press the SLEEP button just once.
If you turn the Monitor off after setting the sleep timer, the setting is erased.
The sleep timer will then have to be set again.
FirstepMonvwCcBaSlmPu&df
Others
35
Auto
picture
control
Use PSM to set the Monitor for the best
-
This function is not available in
RGB, PIP/TWIN PICTURE.
PSM
PSM
1
2
(Picture Status Memory)
Press the PSM button.
Press the PSM or Φ / Γ button to select your
desired picture condition.
PSM
?
Φ
?
?
Dynamic
Γ
Each press of Φ / Γ button
shown below.
Dynamic
changes
Mild
the
screen
display
as
User
You can also select Dynamic, Mild or User in the
Picture menu.
The picture Dynamic, Mild and User are programmed for
good picture reproduction at the factory and cannot be
changed.
36
picture appearance.
Adjusting picture
-
PIP and Twin
picture
inset
settings
are
not
condition
adjustable.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Use the Δ / Ε button to select
Contrast and then press the Γ button.
(to adjust contrast setting)
PSM
Γ
DRP
Contrast
Γ
100
Γ
Brightness
50Γ
Colour
50Γ
Tint
Sharpness
0Γ
50Γ
VOL
?
2
Adjust Brightness, Colour, Tint
Sharpness in the same way.
and
Use the Φ / Γ button to make appropriate adjustments and then press the
OK button.
?
Press the Δ / Ε button to select other items.
PSM
DRP
VOL
Γ
70Γ
Brightness
50Γ
Colour
Tint
Sharpness
VOL
Γ
Contrast
0Γ
0Γ
50Γ
OK
FirstepMonvwCcBaSlmPu&df
Others
37
DRP
Picture)
(Digital Reality
Soft
DRP allows you to select Clear
-
or
for your
picture appearance.
This function works in video, component 480i mode.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Press the Δ / Ε button to select DRP
and then press the Γ button.
PSM
2
Press the Δ / Ε button to select
Dynamic or Mild.
38
OK
Dynamic
Γ
Mild
Colour
50Γ
Sharpness
0Γ
50Γ
APC
Γ
DRP
Contrast
100
Γ
Dynamic
Γ
Mild
Brightness
50Γ
Colour
50Γ
Sharpness
3
Γ
Brightness
Tint
Press the OK button.
100
50Γ
Tint
VOL
Γ
DRP
Contrast
0Γ
50Γ
Selecting
-
Use this
option
when
viewing
menu
the video
options
input.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Use the Δ / Ε button to select Screen
and then press the Γ button.
LANGUAGE
Γ
ARC
Γ
Screen
Γ
TV
Transparency
Γ
VCR
PIP/DW
Γ
Set ID
Γ
VOL
2
UsetheΔ/ΕbuttontoselectTVor
VCR.
?
?
Select the VCR option if watching
Select the TV option for other
a
VCR.
LANGUAGE
Γ
ARC
Γ
Screen
Γ
TV
Transparency
Γ
VCR
PIP/DW
Γ
Set ID
Γ
equipment.(Except VCR)
?
Each time you press the Δ / Ε button you
toggle between TV and VCR.
VOL
3
Press the OK button.
FirstepMonvwCcBaSlmPu&df
Others
OK
39
Adjusting
sound
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Use the Δ / Ε button to select Treble
and then press the Γ button.
(if adjusting treble)
SSM
Γ
AVL
Γ
Treble
50
Bass
50Γ
Balance
Γ
0Γ
VOL
?
2
Adjust
Bass and Balance in the
way.
Use the Φ / Γ button to make appropriate adjustment and then press the
OK button.
?
Press the Δ / Ε button to select other
OK
VOL
40
same
VOL
options.
SSM
AVL
Γ
Γ
Treble
70Γ
Bass
50Γ
Balance
0Γ
Auto sound control
SSM
?
SSM
This function lets you enjoy the best sound without any special adjustment because the Monitor automatically selects the appropriate sound
option based on the program content.
1
Press the SSM button.
2
Press the SSM
desired sound.
SSM
?
or Φ
ΦUserΓ
Each press of SSM
play as below.
or Φ
Flat
?
/ Γ button
changes
the
screen
dis-
Movie
Speech
User
?
/ Γ button to select your
Music
You can also select Flat, Speech, Movie, Music or User
in the Sound menu.
The sound Flat, Speech, Movie and Music are programmed for good sound reproduction at the factory and
cannot be changed.
FirstepMonvwCcBaSlmPu&df
Others
41
AVL
(Auto Volume Leveler)
This feature maintains
an
equal volume level;
even
if you
change channels.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Press the Δ / Ε button to select AVL
and then press the Γ button.
SSM
AVL
Γ
Γ
On
Treble
50Γ
Off
Bass
50Γ
Balance
0Γ
VOL
2
PresstheΔ/ΕbuttontoselectOnor
Off.
SSM
AVL
Γ
On
50Γ
Off
Bass
50Γ
Balance
3
42
Press the OK button.
OK
Γ
Treble
0Γ
Using Still
-
This feature isn't available for RGB
1
STILL
input
function
source.
Press the STILL button.
?
?
You can still the current picture.
The sub picture is stilled in PIP or Twin
picture
mode.
<Moving image>
<Still
2
To return to normal
image>
viewing, press
the STILL button
again.
Tips
?
FirstepMonvwCcBaSlmPu&df
Others
If still picture is on the screen for more than 5 minutes, the image becomes
dark.
If another function is activated, normal brightness of the screen is restored.
43
Adjusting OSD Transparency
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Press the Δ / Ε button to select
Transparency and then press the Γ
button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
5
VOL
2
Press the Φ / Γ button to
transparency.
?
The adjustment range of
0~5.
VOL
3
VOL
Press the OK button.
OK
44
adjust OSD
Transparency
is
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
3
Setting picture format
-
You
are
-
If 4:3 is
-
Don't
ARC
available to 16:9
on
the
display
screen
4:3
or
for
a
4:3 in RGB.
long time,
format
picture
or
that fixed
image may
TWIN PICTURE
remain visible.
on screen
Press the ARC button to select
format.
?
above 10 hours
a
desired
Each time you press ARC or Φ / Γ button, you
select 16:9, 4:3 or Zoom alternatively.
continuously.
picture
can
ARCΦ16:9Γ
<16:9>
ARCΦ4:3Γ
<4:3>
ARCΦZoomΓ
<Zoom>
?
You
can
also select 16:9, 4:3
or
Zoom in the
Special
FirstepMonvwCcBaSlmPu&df
Others
menu.
45
External Control Device
-
Connect the RS-232C input jack to an external control device
and control the Monitor's functions externally.
(such
as a
Setup
computer
or an
A/V control
system)
How to connect external control
?
?
?
Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
RS-232C connection cables are not supplied with the Monitor.
The Monitor remote control and front panel controls (except main power) will not be functional
if the Monitor is controlled by a PC computer or other external device.
RL
AUDO
MONO)VIDEO
AVINPUT
AV INPUT
Y
S-VDEO
YPBPR
RL
AUDIO
(MONO) VIDEO
S-VIDEO
COMPONENT(480i/480p)
(DVD INPUT)
PBR
P
COMPONENT(480i/480p)
(DVDINPUT)
(+)
RL
AUDIO
RGB-PC INPUT
(VGASVGA/XGA/SXGA)
AUDIO INPUT
RS-232C
R
)
EXTERNAL
()
L
(+)
SPEAKER(8Ω)
AC NPUT
(+)
RL
AUDIO
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
AUDIO INPUT
Monitor Rear Connections Panel
46
equipment
R2C
RL
()
()
EXTERNAL
(+)
SPEAKER(8Ω)
AC INPUT
of connector
Type
*
No.
Pin
1
No connection
RXD
3
TXD
9-pin
male
1
5
(Receive data)
(Transmit data)
(DTE side ready)
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
No Connection
a
D-Sub
name
2
Use
:
9
Pin No.4 and Pin
(DCE side ready)
(Ready to send)
(Clear to send)
No.6 must be
connected
6
on
monitor side.
null modem cable.
Wire the 7-Wire cable
so that each pair of data lines cross between the two devices. These data line pairs
(Receive data) and TXD (Transmit data), DTR (DTE side ready) and DSR (DCE side ready), and
RTS (Ready to send) and CTS (Clear to send).
When using the 3-Wire cable connected to RXD, TXD and GND; Pin No. 4 (DTR) and Pin No. 6 (DSR) must
be connected to the monitor. (The cable must be disconnected from the Monitor to be able to use the remote
control and Monitor front panel controls.)
With the RS-232 input connected, the Monitor cannot be controlled by both an external control device and
the remote control at the same time. The Monitor can only be controlled by either the remote control or the
are
*
RXD
external control device.
RS-232C
configurations
3-wire
configuration
(Not standard)
7-wire
configuration
(Standard RS-232C cable)
PC
PDP
PC
RXD
2
TXD
RXD
2
TXD
3
RXD
TXD
3
GND
5
GND
GND
5
DSR
DTR
4
DTR
DSR
6
CTS
RTS
7
RTS
CTS
8
DTR
4
DSR
6
RTS
7
CTS
8
3256487
DB9
PDP
TXD
3254678
DB9
DB9
RXD
GND
DTR
DSR
RTS
CTS
DB9
Control line
7-Wire Cable
?
3-Wire Cable
Configuration
The Monitor is available to switch between external
adjustment
and remote control
adjustment using
a
control line.
Note: If the control line is
trolled
by
?
When
using
Configuration
a
3-Wire cable
configuration
there is
control line. The external control device must
no
put
the
Monitor into the
high,
the monitor is
con-
the external control device. If the control
line is low, the Monitor is controlled
remote control.
by
the Monitor's
"change into remote control adjustment mode" (see page 53). The Monitor will then be
able to be controlled by the remote control. If the
Monitor is turned back on, it will revert back to external device control.
47
FirstepMonvwCcBaSlmPu&df
Others
External Control Device
Adjustments
Set ID
?
Use this function to
specify
a
monitor ID number.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
UsetheΔ/ΕbuttonstoselectSetIDand
then press the Γ button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
1
VOL
2
UsetheΦ/Γ buttontoadjust SetIDto
choose the desired monitor ID number.
?
The
VOL
48
adjustment range
VOL
of Set ID is 1
~
99.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
1
-
The RS-232C
input jack
is used to control the Monitor's functions
Communication Parameters
?
Baud rate
?
Data
:
2400
length
Parity : None
?Stopbit:1bit
Protocol
[Command][ ][Set ID][ ][Data][Cr]
*
Communication code
Receiving
Transmission
bps (UART)
?
?
external control device.
an
Transmission /
8 bits
:
using
:
ASCII code
*
[Command]
[Set ID]
:
To control PDP set.
:
You
can
adjust
the set ID to choose
desired monitor ID number in
*
If the command interval is
seconds, only Command
Be careful when
using
interrupted for more
1 will be recognized.
than 4
See page 48.
is1~99.
menu.
the power command.
When
selecting
Set ID
special
Adjustment range
'0', every connected
PDP set is controlled.
*
[DATA]
:
To transmit command data.
Transmit 'FF' data to read status of
command.
*
[Cr]
:
Carriage
Return
ASCII code '0x0D'
*[]
Command Reference List
:
ASCII code
'space (0x20)'
OK Acknowledgement
[Set ID][:][OK][x][Data][x]
NAME
COMMAND
01. Power
DATA RANGE
*
The Monitor transmits ACK
(acknowledgement) based
receiving normal data. At this
p
0~1
i
0~3
r
0~2
04. Screen mute
m
0~1
05. Volume mute
w
0~1
06. Volume control
v
0~64
07. Contrast
k
0~64
Error Acknowledgement
08.
b
0~64
[Set ID][:][NG][x]
09. Color
c
0~64
10. Tint
t
0~64
02.
03.
Input Select
Aspect Ratio
Brightness
on
time, if the data is data read mode, it indicates present
status data. If the data is data write mode, it returns
the data of the PC computer.
*
11.
s
0~64
12. OSD select
d
0~1
13. Abnormal state
a
0~1
14. PIP/DW
z
0~3
Sharpness
15. PIP
select
e
0~1
16. PIP sound select
u
0~1
17. PIP
x
0~3
j
0~1
input
position
18. remote control
adjustment
this format when
The Monitor transmits ACK
on
this format when
non-viable functions
(acknowledgement) based
receiving abnormal data from
or
communication
errors.
FirstepMonvwCcBaSlmPu&df
Others
mode
49
External Control Device
01. Power
03.
(Command:p)
Aspect
You
[p][ ][Set ID][ ][Data][Cr]
:
[r][ ][Set ID][ ][Data][Cr]
Example : Power on
Type:P31'0x0D'
for set ID No.3.
Data
Acknowledgement
[Set ID][:][OK][x][Data][x]
Data
0
:
In
example
:
0
:
Wide
1
:
Normal
2
:
Full
(16:9)
(4:3)
(Zoom)
screen
screen
screen
Acknowledgement
Power Off
[Set ID][:][OK][x][Data][x]
1:PowerOn
*
format.
also
can
Transmission
Power Off
1:PowerOn
*
(Command:r)
screen
adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in
the Special menu.
Transmission
0
Ratio
Γ To adjust the
Γ To control Power On/Off of the Monitor.
Data
Adjustments
Data
Monitor
Acknowledges
power
on
for set ID
No.3.
Γ To show Power On/Off.
*
0
:
Wide
1
:
Normal
2
:
Full
Using
the PC
(16:9)
(4:3)
(Zoom)
screen
screen
screen
you select either 16:9
input,
or
4:3
screen
aspect ratio.
Transmission
[p][ ][Set ID][ ][FF][Cr]
04. Screen mute
Acknowledgement
[Set ID][:][OK][x][Data][x]
Γ To select
Data
Transmission
*
0
:
Power Off
1
:
Power On
2
:
Power On
3
:
Power On
4
:
Power On
(RGB)
(Video)
(Component)
(S-Video)
In like manner, if other functions transmit 'FF' data
on this format, Acknowledgement data feed
02.
presents
Input
status about each function.
select
Γ To select input
You
can
source
on
an
[i][ ][Set ID][ ][Data][Cr]
0
:RGB
1
:
2
:
3
:
AV
(Video)
Component
S-AV (S-Video)
[Set ID][:][OK][x][Data][x]
50
0:RGB
1
:
2
:
3
:
AV
Screen mute
:
Screen mute off
on
(Picture off)
(Picture on)
[Set ID][:][OK][x][Data][x]
0
:
Screen mute
1
:
Screen mute off
on
(Picture off)
(Picture on)
for the Monitor.
input
source
using
the INPUT
05. Volume mute
Γ To control volume
You
(Video)
Component
S-AV (S-Video)
can
also
(Command:w)
mute on/off.
adjust
mute
using
the MUTE button
remote control.
Transmission
[w][ ][Set ID][ ][Data][Cr]
Data
Acknowledgement
Data
:
1
Acknowledgement
Data
the Monitor's remote control.
Transmission
Data
0
(Command:i)
also select
SELECT button
mute on/off.
[m][ ][Set ID][ ][Data][Cr]
Data
based
back
screen
(Command:m)
0
:
Volume mute
1
:
Volume mute off
on
(Volume off)
(Volume on)
Acknowledgement
[Set ID][:][OK][x][Data][x]
Data
0
:
Volume mute
1
:
Volume mute off
on
(Volume off)
(Volume on)
on
06. Volume control
09. Color
(Command:v)
Γ To adjust volume.
You
on
also
can
(Command:c)
Γ To adjust the
adjust
volume with the volume buttons
remote control.
You
also
can
screen
adjust
color.
color in the Picture
menu.
Transmission
Transmission
[c][ ][Set ID][ ][Data][Cr]
[v][ ][Set ID][ ][Data][Cr]
Data
Data
Refer to 'Real data
*
Refer to 'Real data
*
mapping'
as
shown below.
as
shown below.
[Set ID][:][OK][x][Data][x]
[Set ID][:][OK][x][Data][x]
Data
Min:0~Max:64
Min:0~Max:64
10. Tint
(Command:t)
Γ To adjust the
You
07. Contrast
Γ To adjust
You
screen
also
can
(Command:k)
tint.
tint in the Picture
menu
menu.
Data
Red:0~Green:64
Refer to 'Real data
*
mapping'
as
shown below.
Acknowledgement
[Set ID][:][OK][x][Data][x]
Min:0~Max:64
Refer to 'Real data
adjust
[t][ ][Set ID][ ][Data][Cr]
contrast in the Picture
[k][ ][Set ID][ ][Data][Cr]
*
screen
Transmission
contrast.
adjust
also
can
Transmission
Data
mapping'
Acknowledgement
Acknowledgement
Data
Min:0~Max:64
Min:0~Max:64
mapping'
as
shown below.
Data
Red:0~Green:64
Acknowledgement
[Set ID][:][OK][x][Data][x]
Data
11.
Min:0~Max:64
Sharpness (Command:s)
Γ To adjust the
You
can
also
sharpness.
adjust sharpness in
screen
the Picture
menu
Transmission
08.
[s][ ][Set ID][ ][Data][Cr]
Brightness (Command:b)
Data
Γ To adjust
You
*
also
can
Min:0~Max:64
brightness.
adjust brightness
screen
in the Picture
menu.
Refer to 'Real data
[Set ID][:][OK][x][Data][x]
[b][ ][Set ID][ ][Data][Cr]
Data
shown below.
Min:0~Max:64
Min:0~Max:64
*
Refer to 'Real data
Acknowledgement
[Set ID][:][OK][x][Data][x]
Data
as
Acknowledgement
Transmission
Data
mapping'
mapping'
as
shown below.
*
Real data
0
mapping
:Step0
A:Step10
Min:0~Max:64
Others
F:Step15
10:Step16
64
:
Step
FirstepMonvwCcBaSlmPu&df
100
51
External Control Device
12. OSD select
(Command:d)
Γ To select OSD (On Screen Display) on/off.
14. PIP / DW
Data
You
:OSDoff
1
:OSDon
[Set ID][:][OK][x][Data][x]
*
:OSDoff
1
:OSDon
main
or
0
:PIP/DWoff
1
:
2
:
3
:
PIP
(small)
(large)
Twin picture (DW)
PIP
Acknowledgement
The remote control and Monitor front
(except
remote control
on
[z][ ][Set ID][ ][Data][Cr]
Acknowledgement
0
or twin picture (DW).
using the pip/twin picture
in the Special menu.
also control PIP/DW
Transmission
Data
Data
can
button
0
(Command:z)
Γ To control PIP (Picture-in-Picture)
Transmission
[d][ ][Set ID][ ][Data][Cr]
Adjustments
power)
are
is set up to be controlled
not
by
panel controls
operable when the Monitor
the PC
[Set ID][:][OK][x][Data][x]
Data
computer.
*
PIP
0
:PIP/DWoff
1
:
2
:
3
:
PIP
(small)
(large)
Twin picture (DW)
PIP
following resolutions:
(VGA) / 800x600(SVGA) / 1024x768
(XGA) (only in vertical frequency 60Hz),
Component 480p / 720p / 1080i.
Twin picture works only in the following resolutions:
RGB PC 640x480 (VGA) (only in vertical frequency 60Hz),
Component 480p.
only
works in the
RGB PC 640x480
*
13. Abnormal state
Γ To recognize
an
(Command:a)
abnormal state.
Transmission
15. PIP
input
[a][ ][Set ID][ ][FF][Cr]
Γ To select input
Acknowledgement
You
[Set ID][:][OK][x][Data][x]
Data
0
:OK
1
:
2
:5Vdown
3
:ACdown
source
also select
can
the remote control
(Command:e)
for sub
source
or
in the
picture in PIP mode.
using PIP input button on
Special menu.
Transmission
Fan alarm
[e][ ][Set ID][ ][Data][Cr]
Data
*
select
This function is "read
only".
0
:
AV
1
:
COMPONENT
2
:
S-AV
(VIDEO)
(S-VIDEO)
Acknowledgement
[Set ID][:][OK][x][Data][x]
Data
*
52
0
:
AV
1
:
COMPONENT
2
:
S-AV
(VIDEO)
(S-VIDEO)
COMPONENT
source
only
works with 480i
input signal.
16. PIP sound select
Γ To select main
You
can
special
or
sub
18.
(Command:u)
(inset)
sound for PIP/Twin
also select sound select in PIP/DW
on
Change into Remote control
adjustment mode (Command:j)
picture.
the
Γ
menu.
To control the Monitor with the remote control while
the cable is still connected.
Transmission
Transmission
[u][ ][Set ID][ ][Data][Cr]
Data
[j][ ][Set ID][ ][Data][Cr]
picture sound
1 : Sub picture sound
Acknowledgement
0
:
Main
Data
*
0
:
Main
1
:
Sub
source
Remote control
adjustment
mode
[Set ID][:][OK][x][Data][x]
picture sound
picture sound
COMPONENT
:
Acknowledgement
[Set ID][:][OK][x][Data][x]
Data
1
only
Data
works in 480i
input signal.
*
0
:
PC
1
:
Remote control
If external
"change
Monitor
adjustment
equipment
mode
adjustment
mode
commands the Monitor to
into remote control
can
only
be
adjustment mode", the
adjusted by the remote control.
To revert the Monitor control to external control device
adjustment,
17. PIP
turn the Monitor off and then
on
again.
position (Command:x)
Γ To select sub picture position for PIP.
You
can also adjust the sub picture position using the
position button on the remote control or in PIP/DW on
the Special menu.
Transmission
[x][ ][Set ID][ ][Data][Cr]
Data
down
0
:
Right
1
:
Left down
2
:
Left up
3
:
on screen
on screen
on screen
Right up on
Acknowledgement
screen
[Set ID][:][OK][x][Data][x]
Data
down
0
:
Right
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
FirstepMonvwCcBaSlmPu&df
Others
53
check list
Troubleshooting
No
picture
&
?
Check whether the Monitor is turned
?
Power cord inserted into wall outlet?
on.
No sound
?
?
Press the VOLUME
?
Sound muted? Press MUTE button.
Picture OK &
No sound
?
The remote control
?
doesn't work
?
or
or
Poor color
Poor
picture
Check to
Install
output from one
of the speakers
Strange
sound
from the Monitor
54
button.
if the batteries
(Refer to p.31)
see
new
batteries.
(Refer
are
to
Select Colour in the Picture
(Γ) button. (Refer to p.37)
installed with the correct
p.31)
menu
and press the VOLUME
certain distance between the Monitor and the VCR.
?
Keep
?
Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the
a
screen
No
(Γ)
Check to see if there is any object between the Plasma
Display and the remote control causing obstruction.
polarities.
?
No
Plug another product's power cord into the wall outlet where
the Monitor's power cord was plugged in.
?
Adjust
?
Typical
faulty.
gets dark.)
Balance in the Sound
menu.
sound due to normal Monitor
(Refer
to
operation,
p.40)
Monitor is not
Product
specifications
MT-60PZ11/B/G/K/S
MZ-60PZ13/B/G/K/S
MODEL
(inches
/
mm)
57.3 / 1455
Height (inches
/
mm)
34.8 / 883
Depth (inches
/
mm)
3.9/99
Width
Weight (pounds
Power
/
154.3 / 70
kg)
110-240V~50/60Hz
requirement
1280
Resolution
Color
specifications
improvement.
(Dot)
0~40°C
under 80%
Humidity
The
720
16,770,000 (256 steps of each R, G and B)
Temperature
?
x
shown above may be
changed
without notice for
quality
FirstepMonvwCcBaSlmPu&df
Others
55
P/NO
:
3828VA0303A
a
(NP00KB, 067M TX, 373-026H)
Download PDF