LG | RT-42PY10X | LG RT-42PY10X Owner’s Manual

PLASMA TV
OWNER'S MANUAL
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back
mation to your dealer when you
Model number
:
Serial number
:
P/NO
:
3828VA0509A
(RF043B,
cover
and
quote this infor-
require service.
137F
TX, 026H)
e
Safety Warnings
Instructions
Safety
Safety
Use the set at the
-
place
lower than the altitude of 6562 feet
(2000m)
get the best quality
to
of
picture and
sound.
W
WARNING
Do not
place the
sources
such
This may
-
Do not
or
any
registers,
sunlight
or
stove and
near
heat
so on.
damp place such as
likely to get wet.
bathroom
a
fire
could
or
give
an
In
-
Bend
cable
antenna
building
to
prevent
rain from
This may cause water
electric shock.
-
between
damaged
inside
flowing
case
and
cleaning the
damaged
cause
of smoke
or
the set
strange smell
set.
could
or
give
from the
an
electric
set, switch
from the wall outlet and contact your
service center.
,unplug it
dealer
electric shock.
water while
use
This may
shock.
it off
where it is
cause a
Do not
-
fire.
the set in
place
This may
-
cause a
use
set in direct
heat
as
or
This may
cause a
fire
or
could
give
an
electric shock.
outside
Do not
in.
inside the set and could
give
an
attempt
your dealer
-
This may
shock.
or
to service the set
yourself. Contact
service center.
cause
damaged
the set
or
could
give
an
electric
Earth wire should be connected.
If the earth wire is not connected, there is possible
by the current leakage.
-
a
danger
of
electric shock caused
-
If
grounding
er
should be
methods
are
employed
not
possible, a separate circuit breakby a qualified electrician.
and installed
Power
supplier
Short-circuit
breaker
-
Do not connect
ground to telephone wires, lightning
rods
or
gas
pipe.
Do not
place anything containing liquid
on
top
set.
-
This may
cause a
Do not insert any
-
This may
Do not
-
2
cause a
fire
or
could
cause
PLASMA TV
an
electric shock.
object into the exhaust
fire
or
could
place heavy objects
This may
give
serious
injury
give
on
to
a
an
vent.
electric shock.
the set.
child
or
adult.
During
a
lightning thunder, unplug the
wall outlet and don't touch
of the
-
This may
shock.
cause
damaged
an
set from the
antenna cable.
the set
or
could
give
an
electric
Safety Warnings
*
Safety
instructions have two kinds of
information, and each meaning of it is
as
The violation of this instruction may cause serious
WARNING
The violation of this instruction may cause
NOTES
product.
Take
care
of
below.
injuries
light injuries
and
even
damage
or
death.
of the
danger that may happen under specific condition.
NOTES
Never touch the power
-
This may
cause an
plug with
wet hand.
a
Ensure the power cord doesn't trail
like a heater.
electric shock.
-
Disconnect from the mains and
tions before
remove
all
Do not
This may
Do not
moving.
place the
set in
a
built-in installation such
as a
-
Ventilation
cause a
fire
or an
electric shock.
plug
or
the
when the power cord or the plug is damconnecting part of the power outlet is
loose.
-
or
any hot
connec-
aged
bookcase
across
objects
rack.
This may
cause a
fire
or an
electric shock.
required.
Dispose of used batteries carefully
eating them.
to
protect
a
child
from
-
In
case
When
carry
-
When
installing the set on
place the edge of its stand.
-
a
table, be careful
not to
injury to
child
a
see a
doctor
immediately.
moving the set assembled with speakers do
holding the speakers.
This may cause the set to fall, causing serious
adult, and serious damage to the Monitor.
injury to
a
not
child
or
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
-
This may cause the set to fall, causing serious
adult, and serious damage to the set.
that it eats them, take it to
This may
cause
damaged
the set
or
could
give
an
electric shock.
or
Contact the service center
internal
-
part
once
a
year to clean the
of the set.
Accumulated dust
can cause
mechanical failure.
The distance between eyes and the screen should be
7 times as long as diagonal length of the
about 5
~
screen.
-
If not, eyes will strain.
Unplug the
long periods
Accumulated dust may
deterioration or electric
fire
-
Do not
place
an
outside antenna in the
head power lines
cuits.
-
This may
cause an
There should be
or
other electric
of
vicinity
light or power cirover-
set from the wall outlet when it is left unat-
tended and unused for
cause a
or an
of time.
electric shock from
leakage.
electric shock.
enough distance between
an
outside
power lines to keep the former from
the latter even when the antenna falls.
antenna and
touching
-
This may
Do not
-
cause an
electric shock.
pull the cord but the plug
This may
cause a
when
unplugging.
fire.
Owner's Manual
3
Contents
Contents
Contents
Time Menu
Safety Warnings
SafetyInstructions.......................2~3
Introduction
RemoteControlKeyFunctions................6
LocationandFunctionofControls
.
.
.
.
.
.
.
.
.
.
.7~8
Options
SettingtheClock.........................24
SettingtheOn/OffTimer...................24
AutoSleep..............................24
SleepTimer.............................24
Special Menu Options
ChildLock..............................25
ISM
Installation
External
Equipment Viewing Setups
Displayable Monitor Specification
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.9~12
.
.
InstallationOptions.......................15
TurningontheSet........................16
On-Screen Menu Language Selection (option)
.16
Channel Menu Options
AutoProgrammeTuning...................17
ManualProgrammeTuning.................17
FineTuning.............................18
AssigningaStationName..................18
Booster(option)..........................18
ProgrammeEdit..........................19
FavouriteProgramme.....................19
CallingtheProgrammeTable................19
Picture Menu Options
PSM(PictureStatusMemory)...............20
.
.
.
.
..................................20
AdjustingAutoColourControl.
Manual Colour Temperature Control (User option)
sRGB (RGB[PC], DVI[PC] mode only)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.20
.20
.21
Fleshtone...............................21
Manual Picture Control
.21
(User option)
Options
SSM(SoundStatusMemory)................22
.
.
.
.
.
.
.
.
.
Sound Menu
BBE...................................22
AVL(AutoVolumeLeveler).................22
.22
Adjusting Sound Control (User option)
Stereo/DualReception.....................23
NICAMReception(option)..................23
.
After
reading
this
manu-
al, keep it in the place
where the
always
4
user can
contact
easily.
PLASMA TV
.
.
.
.
.
.
.
.
.
.
.
.25
LEDDISPLAYadjustment..................26
Screen Menu Options
Auto adjustment (RGB [PC] mode only)
.27
SettingPictureFormat.....................27
.
Operation
.
Demo.............................26
.13
Accessories.............................14
Method
(Image Sticking Minimization)
LowPower..............................26
.
.
.
.
.
.
ScreenPosition..........................27
Manual Configure (RGB [PC] mode only)
.28
.28
Selecting Wide VGA/XGA mode (RGB [PC] mode only)
ScreenAdjustments.......................28
.
.
.
.
.
.
.
Cinema................................28
Luminance Noise Reduction
.29
(option)
.29
Initializing (Reset to original factory value)
SplitZoom..............................29
PIP (Picture In Picture) Feature
WatchingPIP............................30
.30
Programme Selection for Sub Picture
.30
Selecting an Input Signal Source for the PIP
.30
MovingthePIP(PIPmodeonly).
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PictureSize.............................30
Adjusting PIP Transparency (PIP
(option)
mode
only)
.
.
.
.30
Teletext
Switchon/off............................31
SIMPLEText(option)......................31
TOPText(option).........................31
FASTEXT..............................32
SpecialTeletextFunctions..................32
Miscellaneous
.33~38
ExternalControlDeviceSetup
IRCode(NECformat)..................39~40
TroubleshootingChecklist..................42
ProductSpecifications.....................43
.
.
.
.
.
.
.
.
.
.
.
Introduction
Introduction
What is
a
Plasma
Display
?
If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent substance.
light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160°
Wide
-
A Plasma
angle range
Display provides
At this moment,
of vision
than 160°
more
angle
range of vision
so
that you
get
can
without distortion from any
picture
a
direction.
Easy
installation
A Plasma
Display is
place.
much
lighter
and smaller than other
same
class
products
so
that you
can
install the Plasma
Display
at the desired
Big
screen
The
screen
of
a
Plasma
Multimedia Plasma
A Plasma
and
The
Display
can
Display
is
42", 50"
or
60"
so
that you
can
get vivid experience
as
if you
are
in
a
theater.
Display
be connected with
a
computer
so
that you
it
can use
as a screen
for
conference, game, internet
so on.
explanation
about coloured dots may be present
The PDP which is the
display
device of this
product
is
composed
in the manufacture of the PDP. Several coloured dots visible
on
on
PDP screen
of 0.9 to 2.2 million cells and
the
screen
would be
a
few cell defects
acceptable,
manufacturers and would not mean that the PDP is faulty. We hope you will understand that the product
sponds to this standard is regarded as acceptable. It means that it could not be changed or refunded.
We promise that we'll do our best to develop our technology to minimize the cell defects.
The
explanation
In the
same
way that
a
fan is used in
a
a
PC to
keep
the CPU
corre-
cool, the PDP is equipped with cooling fans
certain level of noise could
occur
to improve the
operated. This noise doesn't have
difficulty while using this product. The
when the fan is
and
liability and it's also determined to have no
operation of this product. We hope you will understand
changeable nor refundable.
noise from the fans is normal in the
It
which
about noise of PDP
reliability of this product. Therefore,
any negative effect on its efficiency
acceptable.
can occur
in line with other PDP
means
that it is not
that
a
certain level of noise is
TO AVOID BURNING IMAGE INTO THE DISPLAY, DO NOT HAVE A STILL IMAGE ON SCREEN FOR EXTENDED PERIOD
OF TIME. IMAGE AFTER BURN WILL NOT BE COVERED UNDER WARRANTY ie.Menus, Video games, Borders
or
LOGOS
WARNING
This is Class B
case
the
user
product. In a domestic environment this product
may be required to take adequate measures.
may
cause
radio interference in which
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Owner's Manual
5
Introduction
Remote Control
Control
-
-
When
Functions
Key
using the remote control aim it at the remote control sensor of the set.
maybe a defect in consecutive operation of remote control in specified brightness according
There's
Displays
the selected device.
POWER
Switches the set
off to standby.
TV
VCR
MODE
CABLE
TV/AV
Component, RGB
or DVI modes.
AUDIO
TV, AV,
on
from
standby
or
DVD
Selects another device.
ARC
STB
Selects the
to this set feature.
MODE
TV/AV
MULTIMEDIA
Selects the Component, RGB or DVI
modes.
POWE
ARC
MULTIMEDIA
the
Changes
MUTE
MUTE
Switches the sound
on or
off.
Q.VIEW
Returns to the
NUMBER buttons
format.
picture
previously
viewed
programme.
123
FAVOURITE
selects
a
SSM
To select the sound
456
favorite programme.
FAVOURITE
the
Q.VIEW
factory preset picture
according to the room.
0
PSM
MENU
Displays
on screen menus one
by
SSM
one.
VOL
EXIT
Clears all
PIP/DW
PIP/DW
picture
Selects PIP
or
on or
TEXT/
MENU
EXIT
TEXT/* (option)
These buttons are used for teletext.
For further details, see the 'Teletext'
section.
Note : In teletext mode, the PIP PR
+/-, SWAP and PIP INPUT buttons are
used for teletext function.
picture.
SWAP
Alternates between main and sub
OK
pic-
ture.
PIP INPUT
Selects the
input
mode for the sub
pic-
ture.
PIP PR-
PIP INPUT
WIN.SIZE
Adjusts
the sub
menu.
off.
DW modes.
program for the sub
a
displays and
viewing from any
on-screen
returns to TV
PIPPR+/Selects
VOL +/- (Volume Up/Down)
Increases/decreases sound level.
PR +/- (Programme Up/Down)
Selects a programme.
PR
Exits the current menu.
Memorizes menu changes.
Switches the sub
picture
PIP PR+
OK
accepts your selection
SWAP
WIN.POSITION
PLAY
PAUSE
REW
FF
STOP
RECORD
direction.
Selects
REVEAL
VCR BUTTONS
LG video cassette
recorder.
Enlarge
menu
SLEEP
?
SLEEP
Sets the
I/II
item.
LIST
SPLIT ZOOM
the screen with regular
ration.
timer.
LIST
the program table.
Batteries
?
Open
the
battery compartment
insert the batteries with correct
?
PLASMA TV
cover on
new
batteries.
the back side and
polarity.
Install two 1.5V alkaline batteries of AA
batteries with
6
sleep
player.
I/II
Selects the language during dual language broadcast.
Selects the sound output.
Displays
Installing
the
SKP
WIN.SIZE WIN.POSITION
SPLIT ZOOM
displays
D/EorF/G
Adjusts menu settings.
DVD BUTTONS
Controls a LG DVD
a
or
current mode.
size.
MovesthesubpicturetoD/EorF/G
Controls
to
789
PSM
Adjusts
appropriate
programme character.
viewing
your
type. Don't mix used
Introduction
Location and Function of
of Controls
Controls
<Front Panel Controls>
Remote Control Sensor
Power
Standby Indicator
standby
Illuminates red in
mode, Illuminates green
when the set is turned on
ON/OFF
TV/AV
MENU
VOL
PR
TV/AV Button
Selects the
RGB
or
TV, AV, Component,
DVI modes. If OSD is dis-
played,
selects
menu
item.
Main Power Button
MENU
Displays
on screen menus one
by
one.
Exits the current menu.
Memorizes menu changes.
D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Up/Down)
adjusts the volume.
adjusts
menu
settings.
Owner's Manual
7
Introduction
Location and Function of
of Controls
Controls
-
-
-
Shown is
a
simplified representation
of the set.
Here shown may be somewhat different from your set.
This manual explains the features available on the RT-42PY10/11 series.
<Back Panel>
S-VIDEO
AV2
VIDEO
L/MON
AUDIO
8
R
VIDEO
AUDIO
(R)
REMOTE
CONTROL
RS-232C INPUT
(CONTROL/SERVICE)
AUDIO INPUT
DVI INPUT
RGB INPUT
AUDIO
(L)
(R)
VIDEO
L/MONO
COMPONENT
INPUT 2
MONITOR
OUTPUT
COMPONENT
INPUT 1
A/V
INPUT 1
Antenna
S-VIDEO
AC INPUT
1
2
3
4
5
1. CONTROL LOCK / REMOTE CONTROL
6. ANTENNA INPUT
2. RS-232C INPUT(CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
7. POWER CORD SOCKET
This Monitor operates on
cated
3. DVI INPUT / AUDIO INPUT / RGB INPUT
Connect the monitor
output socket of the PERSONAL COM-
PUTER to this socket.
along
with
separate cable.
4. COMPONENT INPUT
Connect DVD video
INPUT and audio
outputs to Y, PB, PR of COMPONENT
outputs to Audio sockets of AUDIO INPUT.
5. AUDIO/VIDEO IN SOCKETS (AV1)
Connect the audio/video out sockets of external
equipment
to
these sockets.
S-VIDEO/AUDIO IN SOCKETS
Connect the S-VIDEO out socket of
an
VCR to the S-VIDEO
socket.
Connect the audio out sockets of the VCR to the audio sockets
8
as
in AV1.
PLASMA TV
the
the Monitor
on
7
AC power. The voltage is indipage. Never attempt to operate
an
Specifications
DC power.
8. AUDIO/VIDEO IN SOCKETS
Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or the EMI Filter
core
on
6
(AV2)
S-VIDEO/AUDIO IN SOCKETS
Installation
External
V iewing Setups
Equipment Viewing
Setups
Antenna Connection
-
Be careful for the bronze wire not to be bended in
connecting
to antenna
input port.
Antenna
Apartments
(connecting
to wall antenna
socket)
wall antenna socket
<
RF coaxial wire
Back
panel
of the set
>
(75 ohms)
VHF antenna
UHF antenna
outdoor antenna
Private house
(connecting
Watching
-
When
Audio
-
-
-
the Monitor to external
Connect the VIDEO INPUT socket
equipment,
(yellow)
match the colours of
to the VIDEO INPUT
on
connecting ports (Video
-
yellow,
Audio
If
a
4:3
VCR.
(Refer
to p.
having
a
fixed
image
remain
on
the
screen
for
a
long period
picture format is used; the fixed image may remain visible on the screen.
picture noise (interference), leave an adequate distance between the VCR
of time.
Typically
a
regular
VCR
TV programmes
Turn the set on and select the programme you
<
VIDEO
AUDIO
(R)
want.
RGB INPUT
(L)
on
AUDIO
frozen still
pic-
(R)
Back
panel
of the set
>
VIDEO
L/MONO
COMPONENT
INPUT 2
MONITOR
OUTPUT
COMPONENT
A/V
INPUT 1
INPUT 1
VCR
1. Use the TV/AV button
a
and set.
Watching
Watching
white,
25)
To avoid
-
-
input.
Use the orbiter function to Avoid
a
(L)
the set.
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set.
If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting
ture from
-
antenna)
VCR
connecting
(R) -red).
to the Video
-
to wall outdoor
Antenna
S-VIDEO
the remote control to
selectAV1 orAV2.
-
If both S-VIDEO and VIDEO sockets have been
connected to the S-VHS VCR
the S-VIDEO
2. Insert
a
video
PLAY button
(See
can
simultaneously, only
be received.
tape into the VCR and press the
on
the VCR.
VCR owner's
manual)
<VCR>
Owner's Manual
9
Installation
External
Watching
After
-
V iewing Setups
Equipment Viewing
Setups
Cable TV
subscribing
for
a
local cable TV station and
For further information of cable
-
<
VIDEO
AUDIO
(R)
PUT
RGB INPUT
installing
a
converter you
can
watch cable TV.
contact the local cable TV station.
TV,
AUDIO
(L)
(R)
Back
panel
of the set
To watch cable TV
>
VIDEO
1. Use the TV/AV button
L/MONO
COMPONENT
INPUT 2
MONITOR
OUTPUT
COMPONENT
INPUT 1
A/V
INPUT 1
Antenna
on
the remote control to
selectAV1 orAV2.
S-VIDEO
2. Tune to cable service
provided
channels
using
the cable box.
<
Watching
-
When
on
external AV
connecting
>
source
the set to
the audio/video
How to
Cable box
an
equipment:
external source, match the colours of AUDIO/VIDEO input
yellow, Audio (Left) white, Audio (Right) red.
Video
=
jacks
on
the set with the
<
on
the remote control to
selectAV1 orAV2.
Operate
the
See external
VIDEO
AUDIO
(R)
AUDIO INPUT
RGB INPUT
corresponding external equipment.
equipment operating guide.
(L)
(R)
PLASMA TV
panel
L/MONO
MONITOR
OUTPUT
COMPONENT
INPUT 1
A/V
INPUT 1
VIDEO
of the set
VIDEO
COMPONENT
INPUT 2
AUDIO
RL
Video game set
Back
AUDIO
Camcorder
10
output jacks
=
use
1. Use the TV/AV button
2.
=
An
S-VIDEO
>
Installation
DVD
Watching
How to connect
<
Back
panel
outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of
of the set
>
Connect DVD video
VIDEO
use
1. Turn
on
the DVD
2. Use TV/AV
player,
and insert
a
(R)
VIDEO
L/MONO
MONITOR
OUTPUT
COMPONENT
INPUT 1
A/V
INPUT 1
Antenna
S-VIDEO
DVD.
MULTIMEDIA button
or
AUDIO
(L)
COMPONENT
INPUT 2
RGB INPUT
AUDIO INPUT.
How to
AUDIO
(R)
T
on
the remote
control to select
Refer to
the
Component 1 or Component 2.
DVD player's manual for operating
instructions.
Component Input ports
You can get better picture quality if you
DVD player with component input ports as
?
Component ports
of the
set
Video
of DVD
Watching
-
To watch
YPBPR
Y
Y
Y
Y
output ports
player
connect
below.
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
<
DVD
player
>
DTV (option)
digitally
broadcast programs,
purchase
and connect
a
digital set-top
box.
How to connect
1. Use the monitor 's COMPONENT (Y, PB, PR) INPUT or RGB jack
for video connections, depending on your set-top box connector.
Then, make the corresponding audio connections.
?
Mode
How to use
1. Turn on the digital set-top box. (Refer to the owner's manual for
the digital set-top box.)
2. Use TV/AV or MULTIMEDIA on the remote control to select
Component 1, Component 2 or RGB.
<
Back
panel
of the set
CONTROL/SERVICE)
AUDIO
(R)
AUDIO INPUT
DVI INPUT
(R)
Input signal
Terminal
Component
RGB
(DTV)
576p(50Hz)
o
o
1080i(50Hz)
o
o
>
VIDEO
RS-232C INPUT
DTV
AUDIO
(L)
RGB INPUT
(R)
VIDEO
L/MONO
MONITOR
OUTPUT
COMPONENT
INPUT 1
A/V
INPUT 1
DTV OUTPUT
(R)
<
AUDIO
(L)
COMPONENT
INPUT 2
Digital Set-top
box
AUDIO
(L)
Y
S-VIDEO
P
PBR
>
Owner's Manual
11
Installation
External
Connecting
-
-
-
-
-
V iewing Setups
Equipment Viewing
Setups
PC
To
enjoy vivid picture and sound, connect a PC to the set.
Avoid keeping a fixed image on the set's screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.
Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of
PC accordingly.
There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC
mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until the
picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the
manufacturer of the PC graphic card.
The synchronization input form for Horizontal and Vertical frequencies is separate.
Setup Instructions to Connect a PC to your set
We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.
If the resolution of PC is over UXGA, there will be no picture on the set.
Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set
-
-
-
output port of the PC
-
-
-
-
-
-
-
to the DVI INPUT
port
or
Connect the audio cable from the PC to the Audio
If
using
a
sound
input on the set. (Audio cables are not included
required.
Play Solution. The set provides EDID data to the PC system with a
card, adjust PC sound
This set
the
signal
cable from the DVI
the set.
on
with the
set).
as
DDC protocol. The PC adjusts
apply a VESA Plug and
automatically to use this set.
DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode.
If required, adjust the set settings for Plug and Play functionally.
If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI
INPUT to display the PC on the set.
If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or DVI; (the other mode
is set to Plug and Play automatically by the set.)
DOS mode may not work depending on video card if using a DVI-I cable.
<
Back
panel
of the set
PC
>
COMPONENT
C INPUT
DVI INPUT
AUDIO INPUT
RGB INPUT
YPBPR
LR
L/SERVICE)
L(MONO)
S-VIDEO
Setup
1. Turn
on
the PC and
2. Turn
on
the
AUDIO
VIDEO
AV4
AUDIO
R
Ante
apply power to the set.
display by pressing the POWER
3. Use the TV/AV
or
MULTIMEDIA button
control to select the RGB
4. Set the resolution
(1280
12
PLASMA TV
button
on
the set's remote control.
x
or
DVI
input
on
the remote
source.
output of the PC to SXGA
1024, 60Hz). (Refer to p. 13)
or
under
Installation
Displayable
Monitor
RGB / DVI mode
Resolution
RGB / DVI mode
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
852x480
800x600
832x624
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
70.09
31.468
70.09
37.861
85.08
37.861
85.08
31.469
70.08
31.469
70.08
640x350
720x400
848x480
Resolution
31.468
640x350
640x480
Specification
Specification
720x400
37.927
85.03
37.927
85.03
31.469
59.94
31.469
59.94
35.000
66.66
35.000
66.66
37.861
72.80
37.861
72.80
37.500
75.00
37.500
75.00
43.269
85.00
43.269
85.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
35.156
56.25
35.156
37.879
60.31
37.879
60.31
48.077
72.18
48.077
72.18
46.875
75.00
46.875
75.00
53.674
85.06
53.674
85.06
49.725
74.55
49.725
74.55
48.363
60.00
48.363
60.00
56.476
70.06
56.476
70.06
1024x768
640x480
848x480
852x480
800x600
832x624
56.25
(RGB)
1024x768
60.023
75.02
60.023
75.02
68.677
85.00
68.677
85.00
1360x768
47.700
60.00
47.700
60.00
(RGB)
59.625
75.02
59.625
75.02
1366x768
47.700
60.00
68.500
85.00
(RGB)
59.625
75.02
47.700
60.00
54.348
60.05
59.625
75.02
1152x864
63.995
70.01
69.500
85.00
(RGB)
67.500
75.00
54.348
60.05
77.487
85.00
63.995
70.01
68.681
75.06
67.500
75.00
47.693
60.00
77.487
85.00
60.091
75.00
68.681
75.06
68.504
85.00
47.693
60.00
(RGB)
60.023
60.02
60.091
75.00
(RGB)
63.981
60.02
68.504
85.00
1280x960
60.023
60.02
1280x1024
63.981
60.02
1360x768
1366x768
1152x864
1152x870
(RGB)
1280x768
(RGB)
1280x960
1280x1024
RT-42PY10X/11X series
1152x870
1280x768
RT-50/60PY10/11 series
Owner's Manual
13
Installation
Accessories
TV
VCR
DVD
CABLE
STB
AUDIO
TV/AV
MODE
MULTIMEDIA
ARC
POWER
MUTE
123
456
789
FAVOURITE
Q.VIEW
0
PSM
SSM
VOL
PR
PIPDW
TEXT/
MENU
EXIT
OK
PIPPR-
PP INPUT
PIPPR+
PLAY
LG TV
1.5V
PAUSE
REW
FF
Owner's Manual
LIST
the TV
Joinning
-
Secure the TV
assembly
to the wall to
assembly by joinning
?
?
it to
a
by using
2-TV brackets
2-Wall brackets
set
6-RING SPACER
(optional)
(Only
RT-60PY10/11
series)
tumbling
the TV/Wall brackets.
Secure the TV
assembly to the
product), as shown.
wall with
strong strings
or
wound wire
cables, (not supplied
Extras
Optional
-
Remote Control handset
After the set must be mounted on s desk top, install the TV brackets on the TV as shown.
Insert the 2 bolts and tighten securely, in the holes on the bracket.
(Only RT-50PY10 series: After removing the existing bolts, insert the 4 bolts and tighten securely, in the holes on the bracket.)
Install the wall brackets on the wall with 4 bolts, (not supplied with the product), as shown.
Match the height of the TV brackets and the wall brackets.
Check to be sure the brackets are tightened securely.
with the
Optional
protect the
wall
SLEEP
/II
(or
Power Cord
RECORD
SKP
WN.POSITON
?
Alkaline batteries
2-TV bracket bolts
RT-50PY10 series: 4-TV
bracket bolts)
(Only RT-60PY10/11 series : 6Wall mounting bracket bolts)
STOP
WIN.SIZE
SPLITZOOM
REVEAL
1.5V
ASmark
SWAP
extras
be
can
changed
or
modified for
quality improvement
without any notification
new
optional
extras
can
be
added.
Contract your dealer for
-
50
42
40
40
42
buying
these items.
50
40
42
40
50
Tilt wall
mounting
bracket
Wall
(Only
Ceiling mounting
14
bracket
PLASMA TV
Desktop
mounting
bracket
RT-60PY10/11
stand
series)
(optional)
Tilt wall
(Only
mounting
bracket
RT-60PY10/11
Video cables
42
series)
Ceiling mounting
Audio cables
bracket
Installation
Installation
?
The set
Desktop
?
The set
can
Options
Options
be installed in different ways such
as on a
wall,
or on a
etc.
desktop
Pedestal Installation
can
be mounted
on a
desk
as
shown above.
(For
further
information, refer
to the
optional 'Desktop
Stand
Installation and
?
Speakers
and
Setup Guide'.)
speaker stands shown
are
optional,
and
are
shown for
example only.
To Install
on a
Desktop
Pedestal mount minimum allowable clearances for
adequate
ventilation.
Wall Mount: Horizontal Installation
?
The set
can
be installed
Bracket Installation and
?
Speakers
are
optional,
on a
wall
as
shown above.
(For
further
information, refer
to the
optional
'Wall
Mounting
Setup Guide'.)
and
are
shown for illustration
only.
To Mount
on a
Wall
Wall mount minimum allowable clearances for ade-
quate ventilation.
10cm
3cm
10cm
10cm
10cm
?
Install the RING SPACER with the bolts
on
the set
as
1. Put the RING SPACER in the holes of the bolts before
necting
to the wall
mounting
bracket.
shown.
con-
(Only
RT-60PY10/11
series)
2. When you connect the wall mounting bracket to the set,
connect to it by using the bolts, (supplied with the product),
as
shown.
Owner's Manual
15
Operation
Turning
Turning
When
-
using
Turning
on
the Set
Set
on
on
the remote
the set
control, aim it
just after
1. Connect power cord
button
on
installation
the set
the set. At this moment, the set is switched to
on
or
press the
control and then the set will switch
Turning
on
1. If the set
the set
was
(power
2. If the set
was
on
NUMBER buttons
on
the set
on
or
PR
the remote
connected)
the set to turn the set
on
the set
on.
turned off with the remote control and the ON/OFF button
Press the ON/OFF button
?
mode. Press the TV/AV
or
on.
cord is still
on
standby
POWER, TV/AV, MULTIMEDIA, PR +/-
turned off with the ON/OFF button
Press the ON/OFF button
?
the set.
sensor on
correctly.
2. Press the ON/OFF button
/
at its
the set and then press the TV/AV or PR
button on the set
/
or NUMBER button on the remote control to turn the set on.
or
press the
POWER,
TV/AV, MULTIMEDIA, PR +/-
On-Screen
On-Screen Menu
-
The
menus can
be shown
on
the
screen
1. Press the MENU button and then
2. Press the
3. Press the
From this
4.
16
in the selected
/
use
language.
First select your
button to select the SPECIAL
language.
menu.
button and then
use
/
button to select
button and then
use
/
button to select your desired language.
will be shown in the language of your choice.
point
Repeatedly
Selection (option)
Language Selection
(option)
on, the
Language.
on-screen menus
press the MENU button to return to normal TV
PLASMA TV
viewing.
Operation
Channel
Channel Menu
Auto
-
Options
Options
Programme Tuning
All stations that
be received
can
stored
are
by
this method. It is recommended that you
use
auto programme
during
installation of this set.
1. Press the MENU button and then
2. Press the
button and then
button to select Auto programme.
button to select System. Select a TV system with the
/
3. Press the
4.
button to select the STATION
/
use
L
:
SECAM L/L'
BG
:
PAL
I
:
menu.
BG
Storage from
2
Start
button to select Start.
6. Press the
button to
auto
begin
SPECIAL
SCREEN
/ South
5. Press the
In
System
TIME
/ Ireland /
are
edit
SOUND
(option)
All receivable stations
Programme
Favourite programme
button;
B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
/Australia)
PAL I/II (U.K.
Auto programme
Manual programme
PICTURE
Hong Kong
Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : (USA / Korea / Philippines) (option)
Press the
button to select Storage from. Select the beginning programme
with the
/
button or NUMBER buttons on the Storage from menu.
Note
STATION
/
PIP/DW
MENU Prev.
number
programming.
stored.
:
models, the station name is stored for stations which broadcast VPS (Video
Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If no station name can be assigned to a station, the channel number is assigned and stored as
C (V/UHF 01-69) or S (Cable 01-47), followed by a number.
b. In Australia, if no station name can be assigned to a station, the channel number is
followed by a number see 'Assigning a station name' secassigned and stored as
tion to assign the station name.
a.
some
-----
To
stop
programming, press the MENU button.
programming is completed, the Programme edit menu appears
See the 'Programme edit' section to edit the stored programme.
auto
When auto
screen.
Manual
-
on
the
Programme Tuning
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you
assign a station name with five characters to each programme number.
1. Press the MENU button and then
2. Press the
button and then
3. Press the
button to select
button
/
4. Press the
L
:
BG
/
:
or
SECAM L/L'
PAL
the
on
System.
menu.
Programme.
Select the desired programme number with the
Storage.
NUMBER buttons
button to select
button to select the STATION
/
use
button to select Manual
/
Storage
Select
a
:
PAL I/II
:
PAL
M
:
(USA /
TV
system
with the
/
button;
(option)
/ Ireland /
Storage
2
System
BG
Band
V/UHF
SOUND
TIME
Fine
SPECIAL
Search
1
Name
SCREEN
PIP/DW
(U.K.
edit
Favourite programme
Hong Kong
/ South
C01
Booster
Off
MENU Prev.
Africa)
Korea /
Philippines) (option)
button to select Band. Press the
button to select V/UHF
/
or
Cable
required.
6. Press the
the
Programme
D/K, SECAM D/K (East Europe / China / Africa / CIS)
5. Press the
as
Auto programme
Manual programme
PICTURE
Channel
Australia)
DK
STATION
menu.
B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
I
can
/
button to select Channel. You
button
or
NUMBER buttons. If
can
possible,
select the desired channel number with
select the channel number
directly
with
the number buttons.
7. Press the
a
button to select Search. Press the
station is found the search will
/
button to
commence
searching.
If
stop.
8. Press the OK button to store it.
9. To store another
station, repeat steps
3 to 8.
Owner's Manual
17
Operation
Channel
Channel Menu
Fine
-
Tuning
Normally
1.
Options
Options
fine
Repeat
is
tuning
only
necessary if
reception
is poor.
the 'Manual programme tuning' steps 1 to 2.
button and then
button to select Fine.
/
STATION
Auto programme
Manual programme
PICTURE
Programme
2. Press the
3. Press the
/
button to fine tune for the best
picture
and sound.
Favourite programme
SOUND
4. Press the OK button.
5.
Repeatedly press
finely tuned
The
the MENU button to return to normal TV
viewing.
programme will be indicated
number
by yellow
edit
programme
selection.
1.
Repeat
a
Band
V/UHF
1
Search
SPECIAL
Name
C01
SCREEN
Booster
Off
Store
Station Name
the 'Manual programme tuning' steps 1 to 2.
button and then
button to select Name.
/
STATION
Auto programme
Manual programme
PICTURE
Programme
2. Press the
3. Press the G button to
4. Press the
display
button. You
the Name
can use a
blank,
menu.
+,
-,
edit
Favourite programme
the
alphabet
A to Z and the numeric 0 to
SOUND
With the
button you
5. Select the next
can
select in the
position by pressing
character, and
the
opposite
2
System
BG
Band
V/UHF
1
Fine
Search
SPECIAL
direction.
Storage
Channel
TIME
9.
ond
BG
Fine
PIP/DW
Assigning
2
System
Channel
TIME
during
Storage
Name
button and then take your choice of the
sec-
Booster
PIP/DW
so on.
C01
SCREEN
Off
Prev.
6. Press the OK button in twice.
7.
Repeatedly
Booster
In
some
If the
1.
press the MENU button to return to normal TV
viewing.
(option)
models, Booster is
reception
Repeat
is poor at the
optional function. Only a set with Booster can perform
fringe area of TV signal, select Booster to On.
an
the 'Manual programme tuning' steps 1 to 2.
button and then
button to select Booster.
/
this function.
STATION
Auto programme
Manual programme
PICTURE
Programme
2. Press the
3. Press the
/
button to select On
or
Off.
Favourite programme
SOUND
4. Press the OK button.
5.
Repeatedly
press the MENU button to return to normal TV
edit
viewing.
TIME
Storage
2
System
BG
Band
V/UHF
Channel
1
Fine
Search
SPECIAL
Name
C01
SCREEN
Booster
PIP/DW
18
PLASMA TV
Store
FG
On
Operation
Edit
Programme
-
This function enables you to delete or skip the stored programmes. Also you can move
gramme numbers or copy a blank station data into the selected programme number.
1. Press the MENU button and then use D / E button to select the STATION
2. Press the G button and then D / E button to select Programme edit.
3. Press the G button to
display
the
Programme
edit
some
stations to other pro-
menu.
Programme
0-
menu.
-
-
-
edit
5C05
-
1BLN2
6C07
2C01
7C55
Deleting
a
3C04
8S27
1. Select
a
4C05
programme
programme to be deleted with the D / E or F / G button.
2. Press the RED button twice.
The selected programme is deleted, all the following programmes
are
shifted up
one
Copying
a
1. Select
a
programme
programme to be
copied
2. Press the GREEN button.
All the following programmes
Moving
1.
2.
3.
4.
Copy
Move
Skip
MENU
position.
with the D
/ E or F / G
shifted down
are
one
9S29
Delete
Prev.
button.
position.
a
programme
Select a programme to be moved with the D / E or F / G button.
Press the YELLOW button.
Move the programme to the desired programme number with the
Press the YELLOW button again to release this function.
D / E or F / G
button.
programme number
programme number to be skipped with the D / E or F / G button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be unable to select it using
the D / E button during normal TV viewing. If you want to select the skipped programme,
directly enter the programme number with the NUMBER buttons or select it in the programme edit or table menu.
Skipping
a
1. Select
Favourite
-
a
Programme
This function lets you select your favourite programmes
1. Press the MENU button and then
2.
3.
4.
5.
6.
7.
8,
E
--
Repeatedly
Calling
-
directly.
button to select the STATION menu.
/
Press the G button and then D / E button to select Favourite programme.
Press the G button to display the Favourite programme menu.
Press the D / E button to select
-----.
Select a desired programme with the F / G button or NUMBER buttons. Any number
under 10 is entered with a numeric '0' (or '00') in front of it, i.e. '05' (or '005') for 5.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
Press the OK button.
Repeatedly press the MENU button to return to normal TV viewing.
use D
You
the
can
?
Auto programme
Manual programme
Programme
PICTURE
edit
Favourite programme
FG
0BLN2
--
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
SOUND
TIME
SPECIAL
SCREEN
PIP/DW
Prev.
press the SWAP button to select stored favorite programmes.
Programme
Table
check the programmes stored in the memory
Displaying programme table
Press the LIST button to display the Programme table
The programme table appears on the screen.
?
STATION
by displaying
the programme table.
menu.
You may find some blue highlighted programmes shown. They have been set up in the
programme edit mode.
Some programmes with the channel number shown in the programme table indicate
there is no station name assigned.
0-
-
-
-
-
5C05
1BLN2
6C07
2C01
7C55
3C04
8S27
4C05
9S29
a programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
The Plasma Display switches to the chosen programme number.
Selecting
Paging through
There
a
programme table
10 programme table pages in which contain 100 programmes.
the D / E or F / G button repeatedly turns the pages.
are
Pressing
Press the LIST button to return to normal TV
viewing.
Owner's Manual
19
Operation
Picture Menu
PSM
-
-
(Picture
Status
This function
Options
Options
Memory)
the set to the best
adjusts
picture appearance.
adjusting picture options (contrast, brightness, colour, sharpness
automatically changed to User.
When
is
and tint
(NTSC input only)) manually,
PSM
1. Press the PSM button
Each press of the PSM button
?
changes
You
?
Picture
the
-
-
You
can
screen
display
shown below.
as
Mild
Standard
Dynamic
?
the
also select Dynamic, Standard, Mild
options Dynamic, Standard
factory and cannot be changed.
and Mild
or
are
User in the PICTURE
User
menu.
preset and programmed for good picture quality
at
enjoy the vivid and hi-definition picture with LG's excellent Digital Reality processor technology.
selecting picture options (Dynamic, Standard and Mild) in PICTURE menu, XD is automatically changed
can
When
to On.
1. Press the MENU button and then
use
button to select the PICTURE
/
menu.
STATION
PSM
PICTURE
CSM
On
2. Press the
3. Press the
button and then
4.
button and then
use
/
use
button to select XD.
button to select On
/
Repeatedly
press the MENU button to return to normal TV
Off
Fleshtone
SOUND
Contrast
Brightness
60
TIME
Colour
50
Sharpness
50
Off.
or
viewing.
100
SPECIAL
SCREEN
PIP/DW
Adjusting
-
MENU Prev.
Auto Colour Control
To initialize values
(reset
to default
settings),
1. Press the MENU button and then
2. Press the
3. Press the
button and then
button and then
use
use
/
use
/
select the Normal
option.
button to select the PICTURE
/
menu.
button to select CSM.
STATION
PSM
PICTURE
CSM
SOUND
Contrast
Brightness
60
Warm
TIME
Colour
50
User
Sharpness
50
Cool
Fleshtone
button to select the desired colour
tempera-
ture.
Normal
100
Red
SPECIAL
4.
?
press the MENU button to return to normal TV
Repeatedly
Each press of
/
button
Cool
Manual Colour
-
You
can
changes
Temperature
green,
or
button and then
button and then
Control
shown below.
PIP/DW
?
5.
20
The
button and then
adjustment
Repeatedly
use
/
button to select the PICTURE
/
menu.
MENU Prev.
STATION
PSM
PICTURE
CSM
SOUND
Contrast
/
/
button to make
Cool
Fleshtone
button to select User.
appropriate adjustments.
range of Red, Green and Blue is -30~+30.
press the MENU button to return to normal TV
PLASMA TV
10
temperature you prefer.
TIME
4. Press the
0
Blue
User
button to select CSM.
/
/
-10
Green
SCREEN
(User option)
use
use
use
display
as
Warm
blue to any colour
1. Press the MENU button and then
3. Press the
screen
Normal
adjust red,
2. Press the
the
viewing.
viewing.
Normal
100
Brightness
60
Warm
Colour
50
User
Sharpness
50
SPECIAL
Red
-10
Green
0
Blue
10
SCREEN
PIP/DW
MENU Prev.
Operation
sRGB
-
(RGB[PC], DVI[PC]
When the set
the
was
equal image
mode
only)
connected to external
equipment
with sRGB
function, It's adjusted
a
colour difference to
1. Press the MENU button and then
use
button to select the PICTURE
/
2. Press the
button and then
use
/
button to select sRGB.
3. Press the
button and then
use
/
button to select On
menu.
STATION
PSM
PICTURE
CSM
or
Off.
TIME
Repeatedly
press the MENU button to return to normal TV
On
sRGB
SOUND
4.
display
each other.
viewing.
Contrast
100
Brightness
60
Colour
50
Off
SPECIAL
SCREEN
PIP/DW
MENU Prev.
Fleshtone
-
-
Adjust the Fleshtone to select the desired skin colour option.
This function works in the following mode:
TV, AV1, AV2, COMPONENT 480i/480p/576i/576p/720p/1080i.
1. Press the MENU button and then
2. Press the
button and then
3. Press the
button and then
use
use
use
button to select the PICTURE
/
menu.
button to select Fleshtone.
/
button to make
/
STATION
PSM
PICTURE
CSM
Fleshtone
SOUND
appropriate adjustments.
TIME
?
4.
The
adjustment
Repeatedly
range of Fleshtone is 0
3.
~
viewing.
-
You
can
In the
Colour
50
Sharpness
50
MENU Prev.
(User option)
adjust picture contrast, brightness, colour, sharpness and tint (NTSC input only) to the levels you prefer.
broadcasting system PAL/SECAM,
1. Press the MENU button and then
use
2. Press the
button and then
use
/
3. Press the
button and then
use
/
4.
60
SCREEN
PIP/DW
-
0
100
Brightness
SPECIAL
press the MENU button to return to normal TV
Manual Picture Control
Contrast
Repeatedly
the
/
picture
item Tint doesn't work.
button to select the PICTURE
button to select the desired
button to make
menu.
picture option.
STATION
PSM
PICTURE
CSM
SOUND
Contrast
Brightness
60
TIME
Colour
50
Sharpness
50
Fleshtone
appropriate adjustments.
press the MENU button to return to normal TV
viewing.
100
SPECIAL
SCREEN
PIP/DW
MENU Prev.
Owner's Manual
21
Operation
Sound
Sound Menu
SSM
-
-
(Sound
Status
Options
Options
Memory)
This function lets you enjoy the best sound without any special adjustment because the set automatically selects the
appropriate sound option based on the program content.
When adjusting sound options (treble and bass) manually, SSM is automatically changed to User.
1. Press the SSM button.
2. Press the SSM button to select your desired sound.
Flat
SRS TSXT
Music
Movie
?
You
?
The sound SRS TSXT, Flat, Music, Movie and Speech
and cannot be changed.
can
also select SRS TSXT, Flat, Music, Movie, Speech
are
or
User
Speech
User in the SOUND
programmed
for
good
menu.
sound
reproduction
at the
factory
R
is
-
-
a
trademark of SRS
TruSurround XT
technology
is
Labs, Inc.
incorporated
under license from SRS
Labs, Inc.
BBE
-
BBE
High
Definition Sound restores
1. Press the MENU button and then
clarity
use
and presence for better
speech intelligibility
button to select the SOUND
/
menu.
and musical realism.
STATION
SSM
PICTURE
AVL
BBE
2. Press the
button and then
use
button to select BBE.
/
Balance
SOUND
3. Press the
button and then
use
button to select On
/
or
Off.
On
Off
0
Treble
50
Bass
50
TIME
4.
Repeatedly
press the MENU button to return to normal TV
viewing.
SPECIAL
SCREEN
PIP/DW
Manufactured under license from BBE
AVL
-
(Auto
Volume
MENU Prev.
Sound, Inc.
Leveler)
This feature maintains
an
equal
volume
1. Press the MENU button and then
level;
use
/
even
if you
change
channels.
button to select the SOUND
menu.
STATION
SSM
PICTURE
AVL
SOUND
Treble
50
Bass
50
BBE
2. Press the
3. Press the
button and then
button and then
use
use
/
/
button to select AV L
button to select On
On
.
or
Balance
Off.
0
TIME
4.
Repeatedly
press the MENU button to return to normal TV
viewing.
SPECIAL
SCREEN
PIP/DW
Adjusting
Sound Control
MENU Prev.
(User option)
1. Press the MENU button and then
use
/
button to select the SOUND
menu.
STATION
SSM
PICTURE
AVL
SOUND
Treble
50
Bass
50
BBE
2. Press the
button and then
use
/
button to select the desired sound item.
3. Press the
button and then
use
/
button to make
4.
Repeatedly
appropriate adjustments.
press the MENU button to return to normal TV
viewing.
Balance
TIME
SPECIAL
SCREEN
Note
22
:
Treble, Bass
PLASMA TV
or
BBE aren't suitable to
use
SRS TSXT.
PIP/DW
MENU Prev.
0
Off
Operation
Stereo / Dual
-
When
tion
Reception
programme is
a
name
selected, the sound information for the station appears after the programme number and
sta-
disappear.
On Screen
Display
Press the I/II button to received broadcast state.
Broadcast
On
Mono
MONO
Stereo
STEREO
Dual
DUAL I
screen
Display
Mono Sound Selection
In stereo
if the stereo
reception
I/II button twice. In
signal is weak, you can switch to mono by pressing the
reception the depth of sound is improved. To switch back to
button twice again.
mono
stereo, press the I/II
Language Selection
If
for Dual
Language Broadcast
programme received in two languages (dual language), you
DUAL II or DUAL I + II by pressing the I/II button repeatedly.
a
?
DUAL I sends the
?
DUAL II sends the
?
DUAL I
NICAM
-
+
sends
II
Sound
output
pressing
?
?
switch to DUAL I,
primary broadcast language to the loudspeakers.
secondary broadcast language to the loudspeakers.
a separate language to each loudspeaker.
Reception (option)
If your Plasma
Instantaneous
?
can
Display is equipped with the PDP Tuner for NICAM reception,
Companding Audio Multiplex) digital sound can be received.
can
be selected
the I/II button
When NICAM
according
repeatedly.
to the
type of received broadcast
as
the
high quality
follows
NICAM
(Near
by
received, you can select NICAM MONO or FM MONO.
received, you can select NICAM STEREO or FM MONO. If
the stereo signal is weak, switch to FM mono.
When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II,
mono
is
When NICAM stereo is
NICAM DUAL I
appears
on
the
+
II,
or
MONO. When FM
mono
is selected the
display
MONO
screen.
Sound
In
output selection
AV, Component, RGB or DVI mode, you
loudspeakers.
Repeatedly press
?
L+R
:
audio R
?
L+L
:
?
R+R
:
Audio
can
select
the I/II button to select the sound
output.
input is sent to left loud-speaker and audio signal
input is sent to right loud-speaker.
Audio signal from audio L input is sent to left and right loud-speakers.
Audio signal from audio R input is sent to left and right loud-speakers.
signal
from audio L
output sound for the left and right
from
Owner's Manual
23
Operation
T ime Menu
Setting
-
Options
Options
the Clock
If current time
setting
is erased
by
a
power
failure, if TV is unplugged
or
if the set is turned off with the ON/OFF button
the set, reset the clock.
on
1. Press the MENU button and then
button to select the TIME
/
use
menu.
STATION
Clock
00
00
:
Off time
PICTURE
2. Press the
button and then
use
/
button to select Clock.
3. Press the
button and then
use
/
button to
adjust
the hour.
4. Press the
button and then
use
/
button to
adjust
the minute.
On time
Auto
sleep
SOUND
5.
Repeatedly
TIME
press the MENU button to return to normal TV
SPECIAL
viewing.
SCREEN
PIP/DW
Setting
-
-
the On/Off Timer
Timer function
operates only if
Off Timer function overrides
-
MENU Prev.
The set must be in
standby
current time has been
Timer function if
on
they
already
are
set.
set to the
same
time.
mode for the On Timer to work.
1. Press the MENU button and then
button to select the TIME
/
use
menu.
STATION
Clock
Off time
2. Press the
button and then
3. Press the
button and then
/
use
/
use
button to select Off time
or
PICTURE
On time.
On time
On
Auto
Off
sleep
SOUND
button to select On.
12
TIME
4. Press the
button and then
use
/
button to
5. Press the
button and then
use
/
button to
6.
Only
On time function; Press the
gramme number or volume level.
7.
Repeatedly
To cancel
-
Auto
/
use
Programme
SPECIAL
SCREEN
button to
adjust
PIP/DW
pro-
MENU Prev.
viewing.
Off/On time function
button has been
step
by
3.
the
on
time function it will
automatically
switch back to
standby
mode
pressed.
Sleep
If there is
-
a
adjust
the minute.
press the MENU button to return to normal TV
button to select Off in
/
Two hours after the set is switched on
unless
the hour.
button and then
Press the
-
adjust
no
input signal,
the monitor turn off
1. Press the MENU button and then
use
automatically
/
after 10 minutes.
button to select the TIME
menu.
STATION
Clock
Off time
2. Press the
button and then
use
/
PICTURE
button to select Auto sleep.
On time
Auto
sleep
4.
button and then
Repeatedly
use
/
button to select On
or
press the MENU button to return to normal TV
Off.
TIME
viewing.
SPECIAL
SCREEN
PIP/DW
Sleep
-
-
timer turns the set off at the
preset time.
Press the SLEEP button to select the number of minutes. The
lowed
by
zz
display
begins
10, 20, 30, 60, 90, 120, 180 and 240 minutes. The timer
---
Min will appear
on
the screen, fol-
to count down from the number of minutes
selected.
a.
To check the
remaining sleep time, press the OK button once.
sleep time, repeatedly press the SLEEP button until the display
the set off after setting the sleep timer, the setting will be erased.
b. To cancel the
c.
24
MENU Prev.
Timer
Sleep
If you turn
PLASMA TV
zz
---
Min appears.
On
Off
SOUND
3. Press the
:
Volume
00
30
1
Operation
Menu
Special
Special
Options
Options
Child Lock
The set
-
be set up
can
so
that it
only
can
1. Press the MENU button and then
2. Press the
button and then
be used with the remote control.
button to select the SPECIAL
/
/
3. Press the
button and then
4.
press the MENU button to return to normal TV
Repeatedly
menu.
STATION
button to select Child lock.
button to select On
/
or
PICTURE
Language
Child lock
On
ISM Method
Off
Low power
SOUND
Set ID
TIME
Index
Off.
Demo
viewing.
SPECIAL
SCREEN
PIP/DW
-
-
-
ISM
-
This set
programmed
to remember which
In Child lock 'On', if the set is turned
TIMEDIA, PR+/- or NUMBER buttons
With the Child lock On, the display
pressed while viewing the set.
(Image Sticking Minimization)
option
it
was
on
'
TV/AV, MUL-
the remote control.
Child lock on' appears
on
the
screen
if any button
on
the front
panel
is
Method
Frozen still picture from a PC/video game displayed
image remaining even when you change the image.
a long period of time.
1. Press the MENU button and then
last set to event if you turn the set off.
button on the set or POWER,
/
off, press the TV/AV, PR
MENU Prev.
use
/
the screen for prolonged periods will result in an ghost
Avoid allowing a fixed image to remain on the set's screen for
on
button to select the SPECIAL
menu.
STATION
Language
Child lock
2. Press the
button and then
PICTURE
ISM Method
Normal
Low power
White wash
SOUND
Set ID
Orbiter
TIME
Index
button to select ISM Method.
/
Demo
3. Press the
Orbiter
button and then
or
button to select either Normal, White wash,
Inversion. If you unnecessary to set this function, set Normal.
/
Inversion
SPECIAL
SCREEN
?
White Wash
White Wash
:
permanent images from the screen.
Note: An excessive permanent image may be impossible to clear entirely with White
removes
PIP/DW
MENU Prev.
Wash.
?
Orbiter
:
Orbiter may help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
screen
?
will
move
Inversion
every 2 minutes.
:
This is the function to invert the
ically
4.
panel
color of the
screen.
The
panel
color is automat-
inverted every 30 minutes.
Repeatedly
press the MENU button to return to normal TV
viewing.
Owner's Manual
25
Operation
Special
Special
Menu
Options
Options
Low Power
-
This is the function to reduce the power
1. Press the MENU button and then
consumption
use
/
of the set.
button to select the SPECIAL
menu.
STATION
Language
Child lock
2. Press the
button and then
3. Press the
button and then
use
use
button to select Low power.
/
button to select On
/
or
PICTURE
ISM Method
Low power
On
SOUND
Set ID
Off
Off.
Demo
TIME
4.
Repeatedly
press the MENU button to return to normal TV
viewing.
Index
SPECIAL
SCREEN
PIP/DW
MENU Prev.
Demo
-
Use it to
see
the difference between XD demo
1. Press the MENU button and then
use
/
on
and XD Demo off.
button to select the SPECIAL
menu.
STATION
Language
Child lock
2. Press the
3. Press the
4. To
stop
XD
button and then
button to
use
button to select XD Demo.
/
PICTURE
ISM Method
SOUND
Set ID
TIME
Index
Low power
XD Demo.
begin
Demo
Demo, press the EXIT button.
To start
SPECIAL
SCREEN
PIP/DW
LED DISPLAY
-
You
can
MENU Prev.
adjustment
switch LED DISPLAY
on or
1. Press the MENU button and then
off.
use
/
button to select the SPECIAL
menu.
STATION
Language
Child lock
2. Press the
3. Press the
button and then
button and then
When you select On
use
use
/
/
button to select Index.
button to select On
or
PICTURE
ISM Method
SOUND
Set ID
TIME
Index
Low power
Off.
mode, The LED DISPLAY illuminates brightly.
Demo
4.
Repeatedly
press the MENU button to return to normal TV
viewing.
SCREEN
PIP/DW
26
PLASMA TV
On
Off
SPECIAL
MENU Prev.
Operation
Screen
Screen Menu
Auto
-
adjustment (RGB [PC]
Options
Options
mode
Automatically adjusts picture position
1. Press the MENU button and then
only)
and minimizes
use D
/ E
image shaking.
button to select the SCREEN
menu.
STATION
Auto
config.
To set
ARC
2. Press the
button and then
G
button to select Auto
/ E
use D
config..
PICTURE
Manual
SOUND
3. Press the G button to start Auto config..
?
When Auto config. has finished, Ok will be shown on screen.
?
If the position of the image is still not correct, try Auto adjustment again.
4. If picture needs to be adjusted
the Manual config..
5.
-
-
Repeatedly
after Auto
in RGB
adjustment
TIME
SPECIAL
(PC),
you
can
adjust
SCREEN
PIP/DW
press the MENU button to return to normal TV
config.
Reset
MENU Prev.
viewing.
Although the image is still not correct, your set is functioning properly but needs further adjustment.
The Auto config. and the Manual config. functions don't need to be run for DVI mode.
Setting
-
more
Position
You
Picture Format
can
watch the
screen
in various
1. Press the MENU button and then
picture formats; Spectacle, Full, Original, 4:3, 16:9 (Wide),
button to select the SCREEN
/
use
menu.
14:9 and Zoom.
STATION
Auto
config.
Spectacle
ARC
2. Press the
3. Press the
16:9, 14:9
?
button and then
button and then
or Zoom.
use
button to select ARC.
/
use
PICTURE
Position
Manual
button to select Spectacle, Full,
/
Original, 4:3,
SOUND
config.
Full
Original
4:3
Reset
16:9
14:9
TIME
Zoom
SPECIAL
Spectacle
When your TV receives the wide screen signal, following selection will lead you to
the picture horizontally, in a linear proportion, to fill the entire screen.
Full
When your TV receives the wide screen signal, following selection will lead you to
the picture horizontally or vertically, in a linear proportion, to fill the entire screen
adjust
SCREEN
PIP/DW
MENU Prev.
?
?
Original
When your TV receives the wide
screen
signal,
it will be
adjust
fully.
automatically changed to the pic-
ture format to be sent.
?
4:3
Following
gray bars
selection will lead you to view
at both the left and
appearing
16:9 (Wide)
Following selection
a picture with
right sides.
an
original
4:3
aspect ratio, with
?
to fill the entire
will lead you to adjust the picture horizontally, in
(useful for viewing 4:3 formatted DVDs).
a
linear
proportion,
screen
14:9
You can enjoy the picture format of 14:9 or general TV programme through the 14:9
mode. The screen 14:9 is viewed just like that the screen 4:3 is magnified to the left /
?
right.
?
Zoom
Following
the entire
4.
-
-
selection will lead you to view the picture without any alternation, while filling
However, the top and bottom portions of the picture will be cropped.
screen.
Repeatedly
You
You
can
can
only
only
press the MENU button to return to normal TV
viewing.
select 4:3 and 16:9 (Wide) in RGB, DVI.
select 4:3, 16:9 (Wide) and Zoom in Component
480p/576p/720p/1080i.
Screen Position
-
This function works in the following mode:
RGB-PC or COMPONENT 480p/576p/720p/1080i.
1. Press the MENU button and then
button to select the SCREEN
/
menu.
STATION
Auto
config.
ARC
2. Press the
button and then
/
button to select Position.
3. Press the
button and then
/
4.
press the MENU button to return to normal TV
or
/
button to
adjust
the
PICTURE
Position
Manual
SOUND
config.
Reset
position.
TIME
Repeatedly
viewing.
SPECIAL
SCREEN
PIP/DW
MENU Prev.
Owner's Manual
27
Operation
Screen
Screen Menu
Manual
-
-
mode
Configure (RGB [PC]
If the
isn't clear after auto
picture
phase manually.
To correct the
Options
Options
only)
adjustment
and
especially
that characters
are
still
trembling, adjust
the
picture
size, adjust Clock.
screen
1. Press the MENU button and then
button to select the SCREEN
/
menu.
STATION
Auto
config.
ARC
2. Press the
button and then
3. Press the
button and then
button to select Manual
/
config.
PICTURE
Manual
SOUND
button to select Phase
/
or
Position
.
Clock.
config.
Phase
0
Clock
0
Reset
TIME
4. Press the
5.
?
The
?
The
-
To
In
see a
some
button to make
adjustment
adjustment
Repeatedly
Selecting
-
/
appropriate adjustments.
SPECIAL
30.
range of Phase is 0
+128.
range of Clock is -127
SCREEN
~
PIP/DW
~
press the MENU button to return to normal TV
Wide VGA/XGA mode
normal
picture,
models, it's
(RGB[PC]
mode
MENU Prev.
viewing.
only)
match the resolution of RGB mode and selection of VGA/XGA mode.
not available to selection of XGA mode.
1. Press the MENU button and then
use
/
button to select the SCREEN
menu.
STATION
Auto
config.
ARC
2. Press the
button and then
use
/
button to select VGA Mode
3. Press the
button and then
use
/
4.
press the MENU button to return to normal TV
(or
XGA
Mode).
button to select the desired VGA/XGA resolution.
PICTURE
Position
Manual
SOUND
config.
Reset
VGA Mode
Repeatedly
640x480
848x480
TIME
852x480
viewing.
SPECIAL
SCREEN
PIP/DW
Screen
-
-
MENU Prev.
Adjustments
Use this function to correct
jittering or picture instability
following mode:
Component 480i/576i.
while
viewing
a
video
tape.
This function works in the
TV, AV1, AV2
or
1. Press the MENU button and then
use
/
button to select the SCREEN
menu.
STATION
Screen
adj.
button and then
3. Press the
button and then
use
button to select Screen
/
PICTURE
adj..
?
Select the VCR
?
Select the TV
button to select TV
/
or
Cinema
YNR
SOUND
use
TV
VCR
ARC
2. Press the
VCR.
Reset
TIME
option if watching a VCR.
option for other equipment.(Except VCR)
SPECIAL
SCREEN
4.
Repeatedly
press the MENU button to return to normal TV
viewing.
PIP/DW
MENU Prev.
Cinema
-
-
When you watch the movie, this function adjusts the set to the best
This function works in the following mode:
TV, AV1, AV2
or
picture
appearance.
COMPONENT 480i/576i.
1. Press the MENU button and then
use
/
button to select the SCREEN
menu.
STATION
Screen
PICTURE
Cinema
On
YNR
Off
adj.
ARC
2. Press the
button and then
use
/
button to select Cinema.
SOUND
3. Press the
4.
Repeatedly
button and then
use
/
button to select On
press the MENU button to return to normal TV
or
Reset
Off.
TIME
viewing.
SPECIAL
SCREEN
PIP/DW
28
PLASMA TV
MENU Prev.
Operation
Luminance Noise Reduction
-
-
You
can
select On
(option)
Off to reduce the
picture
following mode:
Component 480i/576i.
or
noise which may appear
on
the
screen
during watching
the TV.
This function works in the
TV, AV1, AV2
or
1. Press the MENU button and then
use
button to select the SCREEN
/
menu.
STATION
Screen
adj.
ARC
2. Press the
button and then
3. Press the
button and then
use
button to select YNR.
/
use
button to select On
/
or
PICTURE
SOUND
Off.
Cinema
YNR
On
Reset
Off
TIME
4.
Repeatedly
press the MENU button to return to normal TV
viewing.
SPECIAL
SCREEN
PIP/DW
to
Initializing (Reset
This function
original factory value)
operates in
To initialize the
MENU Prev.
current mode.
value
adjusted
1. Press the MENU button and then
button to select the SCREEN
/
menu.
STATION
Screen
adj.
ARC
2. Press the
button and then
3. Press the
button.
/
button to select Reset.
PICTURE
Cinema
SOUND
Reset
YNR
To set
TIME
?
You
can
and sub
initialize
Position, SPLIT ZOOM, PIP size, PIP position, PIP Transparency
size of twin
picture
SPECIAL
picture.
SCREEN
PIP/DW
Split
-
Zoom
This is the function to
-I t 's available to
-
-
use
enlarge
ZOOM, you
If
enlarged,
a screen
is
the
screen
this function in every
With 2-SPLIT
1.
MENU Prev.
can
only
move
with
input
the
a screen can move
ration.
regular
source.
into upside or downside.
selecting a section of screen.
screen
without
Press the SPLIT ZOOM button.
?
Each press of SPLIT ZOOM button
changes
2-Split zoom
the
screen
4-Split
1
display
as
shown below.
9-Split
zoom
1
2
4
5
456
FG
4
In
case
of
9-Split
the
9-Split
/
Zoom:
or
/
enlarged
screen
with
button.
In
zoom
FG
789
Press the number button to select the section you want to enlarge.
If you choose No.5, the 5 section is enlarged and also can move the
using
zoom
123
case
of
choosing
the No.5
123
456
FG
789
The 5 section is
changed
to
a
full
screen.
Owner's Manual
29
Operation
PIP
(Picture-in-Picture)
(Picture-in-Picture) Feature
PIP lets you view 2 different inputs (sources) on your set screen at the
-I t 's not available to use this function in TELETEXT mode.
-
time.
PIP
Watching
Press the PIP/DW button to show the sub
?
same
Each press of PIP/DW button
changes
picture.
the
screen
display
as
shown below.
PIP
DW1
DW2
Off
Selection for Sub Picture
Programme
Press the PIP PR
+
/- button to select
a
Moving
programme for the sub
picture.
mode
(PIP
/
Repeatedly press the
tion is achieved. The sub
Selecting
Input Signal
an
only)
or
picture
/
button until desired
moves
up/down
or
posileft/right.
Source for the PIP
Press the PIP INPUT button to select the
sub
the PIP
Press the WIN.POSITION button.
input
source
for the
picture.
Win.
position
D
FG
E
RGB
AV1
10:30
Picture Size
Press the WIN.SIZE button and then
?
In
RGB, DVI and COMPONENT 480p/576p/720p/1080i for
picture, you can select TV, AV1, AV2 and COMPO-
main
NENT 480i/576i for sub
?
In
TV, AV1,
ture, you
picture.
AV2 and COMPONENT 480i/576i for main
can
select
pic-
TV, AV1, AV2, COMPONENT
480i/480p/576i/576p/720p/1080i,
RGB and DVI for sub
sub
picture
With WIN.SIZE button in
picture
PIP
You can't select the
same
modes for main
pictue
pic-
and sub
picture simultaneously. (except TV)
Win. size
Adjusting
PIP
Transparency (PIP
1. Press the MENU button and then
2. Press the
button and then
3. Press the
button and then
?
4.
30
The
adjustment
Repeatedly
range of PIP
mode
/
only)
button to select the PIP/DW
/
button to select PIP
Transparency.
/
button to
transparency.
adjust
Transparency is
0
PIP
~
10.
press the MENU button to return to normal TV
PLASMA TV
menu.
viewing.
button to
adjust the
DW1, DW2 modes, main and sub
adjusted simultaneously.
mode, sub picture is adjusted.
are
ture.
?
/
size.
With WIN.SIZE button in
Operation
eletext (option)
Teletext
T
(option)
-
Teletext
(or
TOP
text)
is
an
optional function,
therefore
only
the set with the teletext
system
can
receive the teletext
broadcast.
-
-
Teletext is
a
free service broadcast
by
most TV stations which
gives up-to-the-minute
television programmes, share prices and many other topics.
The teletext decoder of this set can support the SIMPLE, TOP and FASTEXT
consists of
TEXT
are
information
on
news,
weather,
systems. SIMPLE (standard teletext)
number of pages which are selected by directly entering the corresponding page number. TOP and FASmore modern methods allowing quick and easy selection of teletext information.
a
Switch on/off
Press the TEXT/* button to switch to teletext.
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time
?
line. The first page number indicates your
are
displayed
on
the
screen
selection, while the second shows the
head-
current
page displayed.
Press the TEXT/* button to switch off teletext.
SIMPLE Text
Page
(option)
selection
1. Enter the desired page number as
during selection you press a wrong
a
three
digit
number, you
and then reenter the correct page number.
2. The PR +/- button can also be used to select the
TOP Text
The
The
number with the NUMBER buttons. If
must
complete
preceding
or
the three
following
digit
number
page.
(option)
guide displays four fields-red, green, yellow and blue at the bottom of the screen.
yellow field denotes the next group and the blue field indicates the next block.
user
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the
yellow
button to
proceed
to the next group with automatic overflow to the next
block.
3. With the green button you can proceed to the next existing page with automatic overflow to the next group. (Alternatively the PR + button can be used.)
4. The red button permits to return to previous selection. (Alternatively the PR button can
-
be
used.)
Direct page selection
Corresponding to the SIMPLE text mode, you can select
digit number using the NUMBER buttons in TOP mode.
a
page
by entering
it
as a
three
Owner's Manual
31
Operation
FASTEXT
The teletext pages are colour coded along the bottom of the
pressing the corresponding coloured button.
screen
and
are
selected
by
Page selection
1. Press the
2. You
button to select the index page.
are colour coded
i
select the pages which
coloured buttons.
3.
4.
can
the bottom line with the
along
Corresponding to the SIMPLE text mode, you can select a page by entering
digit page number with the NUMBER buttons in FASTEXT mode.
The PR+/- button can also be used to select the preceding or following page.
Special
same
its three
Teletext Functions
REVEAL
Press this button to
display
concealed
information, such
as
solutions of riddles
or
puzzles.
Press this button
again
to
remove
the information from the
display.
SIZE
Selects double
height text.
enlarge the top half of the page.
button again to enlarge the bottom half of the
button again to return to the normal display.
Press this button to
Press this
Press this
page.
UPDATE
Displays
the TV
picture
on
the
Press this button to view the
screen
updated
while
waiting
for the
new
teletext page.
teletext page.
HOLD
the automatic page change which will occur if a teletext page consists of 2 or
sub pages. The number of sub pages and the sub page displayed is, usually,
shown on the screen below the time. When this button is pressed the stop symbol
Stops
more
is displayed at the top
change is inhibited.
left-hand
To continue press this button
corner
of the
screen
and the automatic page
again.
MIX
Displays
the teletext pages superimposed on the TV
picture off press this button again.
picture.
To switch the TV
TIME
This button has two functions:
a) When viewing a TV programme, press this button to display the time at the top
right hand corner of the screen. Press this button again to remove the display.
b) In teletext mode, press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or change the sub page,
press the RED/ GREEN or PR+/- buttons. Press this button again to exit this function.
32
PLASMA TV
Miscellaneous
External Control
Control Device Setup
-
Connect the RS-232C
input jack to an external
externally.
control device
(such
as a
computer
or an
A/V control
system)
and control the set's functions
How to connect external control
?
Connect the serial
?
RS-232C connection cables
?
equipment
port of the control device
are
The set remote control and front
computer
or
Back
panel
REMOTE
CONTROL
of the set
panel.
not be functional if the Monitor is controlled
by
a
PC
No.
Pin
1
No connection
>
RS-232C INPUT
DVI INPUT
AUDIO INPUT
RGB INPUT
(CONTROL/SERVICE)
of connector; D-Sub
9-pin
male
1
name
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
5
(Receive data)
(Transmit data)
(DTE side ready)
9
(DCE side ready)
(Ready to send)
(Clear to send)
7
RTS
8
CTS
9
No Connection
RS-232C
Monitor back
other external device.
<
Type
to the RS-232C jack on the
supplied with the set.
panel controls (except main power) will
not
6
configurations
7-wire
(Standard
PC
3-wire
configuration
(Not standard)
configuration
RS-232C cable)
PDP
PC
RXD
2
TXD
RXD
2
TXD
3
RXD
TXD
3
GND
5
GND
GND
5
DSR
DTR
4
DTR
DSR
6
CTS
RTS
7
RTS
CTS
8
DTR
4
DSR
6
RTS
7
CTS
8
D-Sub 9
3256487
D-Sub 9
D-Sub 9
PDP
TXD
RXD
3254678
GND
DTR
DSR
RTS
CTS
D-Sub 9
Owner's Manual
33
Miscellaneous
Set ID
-
-
Use this function to
specify a set ID number.
Mapping 1'. See page 38.
Refer to 'Real Data
1. Press the MENU button and then
use
the
button to select the SPECIAL
/
menu.
STATION
Language
Child lock
2. Press the
button and then
3. Press the
button and then
use
use
button to select Set ID.
/
F / G button to
adjust Set
PICTURE
ISM Method
SOUND
Set ID
TIME
Index
Low power
ID to choose the desired
1
Demo
monitor ID number.
SPECIAL
?
4.
The
adjustment
range of Set ID is 1
99.
~
SCREEN
press the MENU button to return to normal TV
Repeatedly
viewing.
PIP/DW
MENU Prev.
Communication Parameters
?
Baud rate
?
Data
?
*
:
9600
bps (UART)
length : 8
Parity : None
bits
Use
(reverse)
a
crossed
?Stopbit:1bit
?
Communication code
Transmission /
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
[Command1][Command2][ ][Set ID][ ][Data][Cr]
a
0~1
Input Select
Aspect Ratio
k
b
0~6
k
c
0~6
*
04. Screen Mute
k
d
0~1
*
05. Volume Mute
k
e
0~1
06. Volume Control
k
f
0~64
07. Contrast
k
g
0~64
08.
03.
Protocol
Receiving
Transmission
k
02.
ASCII code
cable.
Command Reference List
01. Power
:
*
[Command 1]
First command to control PDP set.
:
(jork)
[Command 2]
[Set ID]
:
Second command to control PDP set.
:
You
can
adjust
the set ID to choose
desired monitor ID number in
menu.
See
special
previous
page.
99.
Adjustment range is 1
When selecting Set ID '0', every
~
k
h
0~64
09. Colour
k
i
0~64
Set ID is indicated
10. Tint
k
j
0~64
menu
11.
k
k
0~64
Brightness
Sharpness
12. OSD Select
k
l
0~1
13. Remote control lock mode
k
m
0~1
14. PIP/DW
k
n
0~3
k
p
0~99
16. PIP Position
k
q
0~3
17. Treble
k
r
0~64
18. Bass
k
s
0~64
19. Balance
k
t
0~64
15.
Split
Zoom
20. Colour
Temperature (CSM) k
u
0~3
21. Red
k
v
0~3C
22. Green
k
w
0~3C
23.
k
$
0~3C
Adjustment
Adjustment
Blue Adjustment
PIP input Source
k
y
0~6
25. Abnormal Status
k
z
0~a
26. ISM Method
j
j
j
j
j
24.
27. Low Power
28. Orbiter Time
29. Orbiter
Setting
Pixel Setting
Size Setting for
30. Picture
DW Mode
p
0~3
q
0~1
r
1~FE
s
1~9
0~1E
t
(or 20)
connected PDP set is controlled.
on
*
[DATA]
command.
*
[Cr]
*[]
[Command2][ ][Set ID][ ][OK][Data][x]
*
The Monitor transmits ACK
(acknowledgement)
this format when
receiving
normal data. At this
data is data read
mode, it indicates present status data. If
mode, it returns the data of the PC
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
*
The Monitor transmits ACK
(acknowledgement)
this format when
abnormal data from
m
b
0~63
3: Wait
34
PLASMA TV
a menu
doesn't
display
Data
on
receiving
non-viable functions
2: not
33,
on
computer.
1
~
based
time, if the
the data is data write
0~63
the 25
'space (0x20)'
OK Acknowledgement
a
setting
ASCII code
:
u
screen.
Return
ASCII code '0x0D'
m
When
Carriage
:
j
*
as
Hexa decimal
Transmit 'FF' data to read status of
32.
33.
as
To transmit command data.
:
31. Auto
Configure
Programme selection
Programme selection
for sub picture
decimal
(1~99)on
(0x0~0x63)
transmission/receiving protocol.
and
1:
Illegal
or
communication
Code
support function
more
time
errors.
based
on
Miscellaneous
01. Power
2
04. Screen Mute
(Command
G To control Power On/Off of the Monitor.
G To select
mute on/off.
Transmission
Transmission
(Command
:
a)
[k][a][ ][Set ID][ ][Data][Cr]
Data
0
d)
:
[k][d][ ][Set ID][ ][Data][Cr]
Power Off
:
screen
2
Data
1:PowerOn
0
:
Screen mute off
1
:
Screen mute
(Picture on)
(Picture off)
on
Ack
Ack
[a][ ][Set ID][ ][OK][Data][x]
[d][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Transmission
05. Volume Mute
(Command
[k][a][ ][Set ID][ ][FF][Cr]
G To control volume
mute on/off.
Ack
You
adjust
mute
the MUTE button
using
on
Transmission
In like manner, if other functions transmit '0xFF' data
based on this format, Acknowledgement data feed back
[k][e][ ][Set ID][ ][Data][Cr]
Data
status about each function.
presents
also
e)
:
remote control.
[a][ ][Set ID][ ][OK][Data][x]
*
can
2
0
:
Volume mute
1
:
Volume mute off
(Volume off)
(Volume on)
on
Ack
02.
Select
Input
G To select input
You
(Command
source
also select
can
SELECT button
on
an
2
:
[e][ ][Set ID][ ][OK][Data][x]
b)
for the Monitor.
input
source
using
the INPUT
the Monitor's remote control.
You
on
[k][b][ ][Set ID][ ][Data][Cr]
0
:TV
4
:
(Command
Component2
can
also
adjust
Transmission
1
:AV1
5
:RGB
[k][f][ ][Set ID][ ][Data][Cr]
:AV2
6
:DVI
Data
3
:
Component1
Min:0~Max:64
*
Refer to 'Real data
mapping
Ack
[b][ ][Set ID][ ][OK][Data][x]
[f][ ][Set ID][ ][OK][Data][x]
07. Contrast
Ratio
G To adjust the
(Command
2
:
Picture
c) (Main
Size)
format. (Main picture format)
adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
You
screen
also
can
SCREEN
menu.
G To adjust
You
:
Spectacle
1:full
2
:
Original
3
:
Normal
screen
4
:
Wide
screen
5
:
Wide
screen
6
:
Full
screen
(16:9)
(14:9)
(Zoom)
(4:3)
the PC
aspect ratio.
input,
contrast.
adjust
contrast in the PICTURE
menu.
Min:0~Max:64
Refer to 'Real data
mapping
1'. See page 38.
you select either 16:9
[g][ ][Set ID][ ][OK][Data][x]
08.
Brightness (Command
G To adjust
[c][ ][Set ID][ ][OK][Data][x]
Using
also
g)
:
Ack
Ack
*
screen
2
[k][g][ ][Set ID][ ][Data][Cr]
*
[k][c][ ][Set ID][ ][Data][Cr]
can
(Command
1'. See page 38.
Transmission
Data
Transmission
Data 0
f)
volume with the volume buttons
2
Aspect
:
remote control.
Ack
03.
2
G To adjust volume.
Transmission
Data
06. Volume Control
You
or
4:3
screen
can
2
brightness.
adjust brightness
:
h)
screen
also
in the PICTURE
menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Refer to 'Real data
mapping
1'. See page 38.
Ack
[h][ ][Set ID][ ][OK][Data][x]
Owner's Manual
35
Miscellaneous
09. Colour
(Command
G To adjust the
You
can
also
screen
adjust
2
i)
:
14.PIP/DW(Command2:n)
G To control the PIP (Picture In picture)/DW.
colour.
colour in the PICTURE
You
menu.
on
Transmission
Refer to 'Real data
the PIP/DW button
menu.
[k][n][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
*
using
in the PIP/DW
or
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data
also control the PIP/DW
can
the remote control
mapping
1'. See page 38.
Data
0: PIP/DW off
Ack
1: PIP
[i][ ][Set ID][ ][OK][Data][x]
2: DW1
3: DW2
10. Tint
(Command
G To adjust the
You
can
also
screen
adjust
2
:
Ack
j) (option)
[n][ ][Set ID][ ][OK][Data][x]
tint.
tint in the PICTURE
menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data
15.
Red:0~Green:64
*
Refer to 'Real data
mapping
Split
Zoom
(Command
G To operate split
1'. See page 38.
zoom
2
:
p)
function and select the
split
section number.
Ack
Transmission
[j][ ][Set ID][ ][OK][Data][x]
[k][p][ ][Set ID][ ][Data][Cr]
Data
11.
Sharpness (Command
G To adjust the
You
can
also
2
Min: 0
k)
:
sharpness.
adjust sharpness in
?
menu.
Transmission
Max: 99
Selection 1 of 2
Refer to 'Real data
screen
the PICTURE
~
Data 21:
ex.
split
zoom.
2'.
mapping
Ack
[p][ ][Set ID][ ][OK][Data][x]
[k][k][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Refer to 'Real data
Real data
*
mapping
1'. See page 38.
0
Ack
Reset
:
split
zoom
21: Selection 1 of 2
[k][ ][Set ID][ ][OK][Data][x]
zoom
91: Selection 1 of 9
split
split
split
split
split
split
split
99: Selection 9 of 9
split
zoom
24: Selection 4 of 2
41: Selection 1 of 4
42: Selection 2 of 4
12. OSD Select
(Command
2
:
l)
44: Selection 4 of 4
G To select OSD (On Screen Display) on/off when
45: Selection 5 of 4
con-
trolling remotely.
Transmission
2
mapping
zoom
zoom
zoom
zoom
zoom
zoom
[k][l][ ][Set ID][ ][Data][Cr]
Data0
:OSDoff
1:OSDon
Ack
16. PIP Position
[l][ ][Set ID][ ][OK][Data][x]
You
13. Remote control lock mode
G To lock the front panel controls
(Command
on
2
:
m)
the monitor and remote
control.
:
PIP/DW
Lock off
1:Lockon
Ack
[m][ ][Set ID][ ][OK][Data][x]
*
If
you're
not
using
the remote
When main power is
released.
36
also
adjust
the sub
on
PLASMA TV
2
:
q)
picture position using
the remote control
menu.
Transmission
Data
[k][m][ ][Set ID][ ][Data][Cr]
0
can
WIN.POSITION button
[k][q][ ][Set ID][ ][Data][Cr]
Transmission
Data
(Command
G To select sub picture position for PIP.
control, use this mode.
on/off, external control lock is
down
0
:
Right
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
Ack
[q][ ][Set ID][ ][OK][Data][x]
or
in the
zoom
Miscellaneous
17. Treble
(Command
2
22. Green
:r)
G To adjust treble.
You
can
also
adjust
treble in the SOUND
menu.
w)
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
[k][r][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
:
G To adjust green in colour temperature.
Transmission
Data
2
Adjustment (Command
Refer to 'Real data
Min:0~Max:3C
Refer to 'Real data
*
mapping
1'. See page 38.
Ack
mapping
3'. See page 38.
Ack
[w][ ][Set ID][ ][OK][Data][x]
[r][ ][Set ID][ ][OK][Data][x]
23. Blue
18. Bass
(Command
2
:
s)
can
also
adjust
Transmission
bass in the SOUND
menu.
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data
Refer to 'Real data
Refer to 'Real data
3'. See page 38.
mapping
Ack
Min:0~Max:64
*
Min:0~Max:3C
*
[k][s][ ][Set ID][ ][Data][Cr]
Data
$)
:
G To adjust blue in colour temperature.
G To adjust bass.
You
2
Adjustment (Command
mapping
1'. See page 38.
[$][ ][Set ID][ ][OK][Data][x]
Ack
24. PIP
[s][ ][Set ID][ ][OK][Data][x]
Input
Select
G To select input
19. Balance
(Command
2
:
t)
ture mode. You
picture using
G To adjust balance.
You
can
also
adjust
balance in the SOUND
menu.
can
y)
:
for sub
also
picture in PIP/Twin picadjust input source for sub
PIP INPUT button
remote control.
on
Transmission
Data
[k][t][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
*
source
2
[k][y][ ][Set ID][ ][Data][Cr]
Transmission
Data
(Command
Refer to 'Real data
mapping
1'. See page 38.
Ack
0
:TV
4
:
1
:AV1
5
:RGB
2
:AV2
6
:DVI
3
:
Component2
Component1
Ack
[t][ ][Set ID][ ][OK][Data][x]
20. Colour
[y][ ][Set ID][ ][OK][Data][x]
Temperature (Command
2
:
u)
G To adjust colour temperature.
You
can
also
adjust
CSM in the PICTURE
menu.
25. Abnormal State
G To recognize
an
(Command
:
z)
abnormal state.
Transmission
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
[k][z][ ][Set ID][ ][FF][ ][Cr]
Data
Data
0: Cool
2
1: Normal
2: Warm
3: User
FF
:
Read
Ack
Ack
[z][ ][Set ID][ ][OK][Data][x]
[u][ ][Set ID][ ][OK][Data][x]
Data
0: Normal
(Power on and signal exist)
signal (Power on)
Turn the monitor off by remote control
Turn the monitor off by sleep time function
Turn the monitor off by RS-232C function
1: No
21. Red
Adjustment (Command
2
:
v)
2:
3:
G To adjust red in colour temperature.
4:
Transmission
5: 5V down
6: AC down
[k][v][ ][Set ID][ ][Data][Cr]
Data
7: Turn the monitor off
Min:0~Max:3C
*
Refer to 'Real data
mapping
8: Turn the monitor off
3'. See page 38.
9: Turn the monitor off
Ack
[v][ ][Set ID][ ][OK][Data][x]
a:
*
Turn the monitor off
This function is "read
by
by
by
by
Fan Alarm function
Off time function
Auto
sleep
function
On time function
only".
Owner's Manual
37
Miscellaneous
Data
26. ISM Method
(Command
1
:
j,
Command 2
G To control the ISM method. You
Method in SPECIAL
:
Min: 0
*
p)
~
Max: 1E
(or 20)
mapping
Refer to 'Real data
1'. See page 38.
Ack
also
can
adjust
ISM
[t][ ][Set ID][ ][OK][Data][x]
menu.
Transmission
31. Auto
Configure
(Command 1 : j,
[j][p][ ][Set ID][ ][Data][Cr]
Data
0
:
1
:
Normal Mode
2
:
White Wash
3
:
Orbiter
Command 2
:
u)
G To adjust picture position and minimize image shaking
Inversion
automatically.
Ack
It works
only
in RGB
(PC)
mode.
Transmission
[p][ ][Set ID][ ][OK][Data][x]
[j][u][ ][Set ID][ ][Data][Cr]
Data
27. Low Power
(Command
1
:
j,
Command 2
:
q)
G To reduce the power consumption of the monitor. You
also
can
Low Power in SPECIAL
adjust
[u][ ][Set ID][ ][OK][Data][x]
menu.
32.
Transmission
Programme selection
(Command 1 : m, Command
[j][q][ ][Set ID][ ][Data][ ][Cr]
Data
1: To set
Ack
0:Off
G To select
1:On
Transmission
Ack
2
programme for the main
a
:
a)
picture.
[m][a][ ][Set ID][ ][Data][Cr]
[q][ ][Set ID][ ][OK][Data][x]
Data
Min:0~Max:63(0~C7,200Prison)
Refer to 'Real data mapping 1'.
*
28. Orbiter Time
(Command
Setting
: j, Command
1
G To adjust orbiter operation time
Ack
2
:
r)
[a][ ][Set ID][ ][OK][Data][x]
term.
Transmission
33.
Programme selection for sub picture
(Command 1 : m, Command 2 : b)
[j][r][ ][Set ID][ ][Data][ ][Cr]
Data
Min: 1
*
~
Max: FE
Refer to 'Real data
G To select
mapping
1'.
programme for the sub
a
picture.
Transmission
Ack
[m][b][ ][Set ID][ ][Data][Cr]
[r][ ][Set ID][ ][OK][Data][x]
Data
Min:0~Max:63(0~C7,200Prison)
Refer to 'Real data mapping 1'.
*
29. Orbiter Pixel
(Command
Setting
: j, Command
1
2
:
Ack
s)
G To adjust pixel number in orbiter function.
[b][ ][Set ID][ ][OK][Data][x]
Transmission
[j][s][ ][Set ID][ ][Data][Cr]
*
Data
Min:1~Max:9
*
Refer to 'Real data
mapping
1'.
Real data
mapping
1
Real data
0
:Step0
0:-30
A
:Step10(SetID10)
2:-28
1:-29
Ack
[s][ ][Set ID][ ][OK][Data][x]
30. Picture Size
(Command
1
F :Step15(SetID15)
10:Step16(SetID16)
for DW Mode
Setting
: j, Command
2
:
You
can
also select the PIP
WIN.SIZE
on
picture
64
:
Step
100
6E
:
Step
110
73
:
:
Step
Step
115
74
C7
:
Step
199
using
the
[j][t][ ][Set ID][ ][Data][Cr]
PLASMA TV
3B:+29
3C:+30
format
the remote control.
Transmission
1E:0
3A:+28
t)
G To select the PIP picture format.
38
*
116
mapping
3
Miscellaneous
IR Code
Code
(NEC
(NEC Format)
How to connect
G
Connect your wired remote control to the Remote Control
Remote Control IR Code
port
on
the Monitor.
(NEC Format)
G Output waveform
Single pulse,
modulated with 37.917KHz
at 455KHz
signal
TC
Carrier
frequency
FCAR
1/TC
Duty
T1
=
ratio
=
=
fOSC/12
T1/TC
1/3
=
G Configuration of frame
?
1st frame
Lead
Low
High
code
custom code
custom code
Data code
Data code
C0 C1C2C3C4C5C6C7C0C1C2C3C4C5C6C7D0D1D2D3D4D5D6D7D0D1D2D3D4D5D6D7
?
Repeat
frame
Repeat
code
Tf
G Lead code
9ms
4.5
ms
0.55
G Repeat code
ms
9ms
2.25
ms
G Bit description
?
?
Bit "0"
0.56
0.56
1.12
G Frame interval
:
Bit "1"
ms
ms
2.24
ms
ms
Tf
The waveform is transmitted
Tf
as
long
as a
key
is
depressed.
Tf
Tf=108ms @455KHz
Owner's Manual
39
Miscellaneous
Code
Note
00
PR+
R/C Button
01
PR-
R/C Button
02
VOL+
R/C Button
03
VOL-
R/C Button
40
Up (D)
Down (E)
Right (G)
Left (F)
R/C Button
08
POWER
R/C Button
C4
POWER ON
Discrete IR Code
C5
POWER OFF
Discrete IR
09
MUTE
R/C Button
10
Number
11
Number
12
Number
13
Number
14
Number
15
Number
16
Number
17
Number
18
Number
19
Number
0B
TV/AV
R/C Button
98
MULTIMEDIA
R/C Button
BF
COMPONENT1
Discrete IR Code
D4
COMPONENT2
Discrete IR Code
C6
DVI
Discrete IR Code
D5
RGB
Discrete IR Code
41
06
07
40
Function
(Hexa)
Key
Key
Key
Key
Key
Key
Key
Key
Key
Key
R/C Button
R/C Button
R/C Button
0
R/C Button
1
R/C Button
2
R/C Button
3
R/C Button
4
R/C Button
5
R/C Button
6
R/C Button
7
R/C Button
8
R/C Button
9
R/C Button
(Power On/Off)
(Only Power On)
Code (Only Power Off)
D6
TV
Discrete IR Code
5A
AV1
Discrete IR Code
D0
AV2
Discrete IR Code
0A
I/II
R/C Button
0E
SLEEP
R/C Button
43
MENU
R/C Button
44
OK( )
R/C Button
4D
PSM
R/C Button
52
SSM
R/C Button
53or70
LIST
R/C Button
20
TEXT/*
R/C Button
2A
REVEAL
R/C Button
22
MODE
R/C Button
24
MIX
R/C Button
26
TIME
R/C Button
62
UPDATE / WIN.POSITION
R/C Button
64
SIZE / WIN.SIZE
R/C Button
65
HOLD
R/C Button
70
INDEX
R/C Button
60
PIP/DW
R/C Button
61
PIP INPUT
R/C Button
63
SWAP
R/C Button
71
PIP PR+
R/C Button
72
PIP PR-
R/C Button
7B
SPLIT ZOOM
R/C Button
79
ARC
R/C Button
76
ARC
77
ARC
AF
ARC
PLASMA TV
(4:3)
(16:9)
(Zoom)
Discrete IR Code
Discrete IR Code
Discrete IR Code
(Input
(Input
(Input
(Input
(Input
(Input
(Input
(Only
(Only
(Only
COMPONENT1
COMPONENT2
DVI
Selection)
Selection)
TV Selection)
AV1 Selection)
AV2 Selection)
RGB
4:3
mode)
mode)
Zoom mode)
16:9
Selection)
Selection)
Miscellaneous
Notes
Owner's Manual
41
Miscellaneous
Checklist
Checklist
Troubleshooting
Troubleshooting
No
picture
&
?
Check whether the set is turned
?
Power cord inserted into wall outlet?
on.
No sound
?
another
was
?
Sound muted? Press MUTE button.
Check to
causing
?
The remote control
see
to
p.6)
No
new
batteries.
as
the
(Refer
to
image
is muted
p.6)
during the startup process of
picture has not appeared
Please contact your service centre, if the
minutes.
Select Colour in the PICTURE
to
menu
Keep
?
Activate any function to restore the
still
one
of the
Unusual sound from
inside the set
picture
is
on
the
screen
for
?
Check for local interference such
?
Adjust
?
A
PLASMA TV
Balance in the SOUND
change
in ambient
at the time of
the set.
after five
and press the G button.
certain distance between the set and the VCR.
?
a
the set.
p.21)
of the
brightness
more
as an
than 5
menu.
electrical
(Refer
picture.
minutes, the
picture shaking
output from
polarities.
This is normal
speakers
42
installed with the correct
are
?
(If
or
if the batteries
Install
picture
Horizontal/vertical bars
between the set and the remote control
object
Check if the remote control handset is set up to correct mode.
(Refer
Poor colour
if there is any
see
?
?
Poor
button.
?
Picture appears slowly,
after switching on
or
(+)
obstruction.
Check to
(Refer
doesn't work
or
power cord into the wall outlet where the set's power
Press the VOLUME
?
No
product's
plugged in.
?
Picture OK &
No sound
Plug
cord
to
appliance
screen
or
gets dark.)
power tool.
p.22)
humidity or temperature may result in an unusual noise
switching off or on of the set and does not indicate a fault with
Miscellaneous
Product
Specifications
MODEL
Width
RT-42PY10X/H
RT-42PY11X/H
(inches
/
mm)
48 / 1216
48 / 1216
Height (inches
/
mm)
27/691
25/630
Depth (inches
/
mm)
10.7 / 271.4
3.8/96
Weight (pounds
Power
/
86/39
kg)
70.5 / 32
AC100-240V, 50/60Hz
requirement
Resolution
1024
768
Colour
16,770,000 (256 steps
Operating Temperature Range
32
MODEL
Width
104°F
(0
R, G and B)
40°C)
~
RT-50PY10/H
RT-50PY11/H
(inches
/
mm)
Height (inches
/
mm)
31.4 / 798.5
29/734
Depth (inches
/
mm)
12 / 302.5
3.9/98
/
122 / 55.3
98 / 44.5
Weight (pounds
Power
kg)
55 / 1402
55 / 1402
AC100-240V, 50/60Hz
requirement
Resolution
1366
Colour
32
768
(Dot)
MODEL
~
104°F
(0
40°C)
~
Less than 80%
Operating Humidity Range
Width
x
16,770,000 (256 steps of each R, G and B)
Operating Temperature Range
RT-60PY10/H
RT-60PY11/H
(inches
/
mm)
67 / 1708
67 / 1708
Height (inches
/
mm)
37/931
34/862
Depth (inches
/
mm)
13 / 320.7
3.9/99
188.5 / 85.5
146 / 66.2
Weight (pounds
Power
/
kg)
AC100-240V, 50/60Hz
requirement
Resolution
1366
Colour
32
shown above may be
768
(Dot)
~
104°F
(0
40°C)
~
Less than 80%
Operating Humidity Range
specifications
x
16,770,000 (256 steps of each R, G and B)
Operating Temperature Range
The
~
(Dot)
of each
Less than 80%
Operating Humidity Range
?
x
changed
without notice for
quality improvement.
Owner's Manual
43
Download PDF

advertising