LG | WZ-6807WFL | LG WZ-6807WFL Owner's manual

DISHWASHER
OWNER'S MANUAL
MODEL : D1422W(L,M,T,B,C,D,A)F(B,U)
D1423W(L,M,T,B,C,D,A)F(B,U)
WZ-6807WFL
WZ-6807MFL
Please read this manual carefully before operating your
dishwasher. Retain it for future reference.
C
ONTENTS
SAFETY AND CAUTION
3
INSTALLATION INSTRUCTIONS
5
PARTS NAME
9
FUNCTION OF CONTROL BUTTON
10
BEFORE USING FOR THE FIRST TIME
13
HOW TO USE AND OPERATE
15
OPERATING SEQUENCE
21
PROGRAM
22
USER MAINTENANCE INSTRUCTIONS
23
TROUBLE SHOOTING GUIDE
24
SPECIFICATION
S
AFETY AND CAUTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING - When using your dishwasher, follow basic precautions,
including the following:
During use
• Please read this manual carefully before using
the dishwasher for the first time.
• This manual contains very important notes
regarding the installation, use and maintenance
of your dishwasher.
• The manufacturer can not be responsible for
problems caused by ignoring these safety and
caution instructions.
• This dishwasher is designed for normal
household use.
• Do not use the dishwasher for industrial and
commercial use, or other purpose.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• Check packaging and dishwasher immediately
for signs of transport damage. If the appliance
is damaged, do not put it into use but contact
your supplier without delay.
• Only suitable household utensils should be
placed in the dishwasher.
(Please avoid utensils; that are nonheatresistant, metal decorated, etc.)
• Do not use any kinds of solvent in your
dishwasher. They may cause an explosion or
fire.
• Do not spray water on the appliance.
It may cause the failure of electric parts or
electric shock.
• Do not push down or sit on the inner door
when the door opened. It may cause the
deformation or failure of your dishwasher.
• Do not use the detergent for hand washing.
The detergent for dishwasher should be used
for normal operation.
• This appliance is fitted with a safety function
that automatically stops the operation of the
dishwasher when it is exposed to heavy
disturbance on its mains.
• Dishwasher detergents are strongly alkaline.
They can be extremely dangerous if
swallowed. Avoid contact with skin and eyes
and keep children away from the dishwasher
when the door is open.
Check that the detergent receptacle is empty
after completion of the wash cycle.
During installation
• Electrical connection must be in accordance
with the rating label.
• Electrical safety is only guaranteed when the
earth system of your house is in accordance
with the related local regulations.(Do not use
an extension cable or cord.)
• If the hot water exceeds 65ºC, adjust the water
heater setting. If the hot water temperature can
not be maintained below 65ºC, the dishwasher
must be connected to cold water.
• If power supply cord is damaged, it must only
be replaced by the manufacturer or its service
agent or a similar qualified person in order to
avoid a hazard.
• This appliance must be positioned so that the
plug is accessible.
• The appliance is to be connected to the water
mains using new hose-sets and that old hosesets should not be reused.
Child Safety
• Controls may be locked using “Child Lock”
mode to prevent from all the setting from
being changed by a child.
• Keep children away from detergents and rinseaids.
• Do not allow children to operate the
dishwasher.
• Young children should be supervised to ensure
that they do not play with the appliance.
3
S
AFETY AND CAUTION
CAUTION
concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the
cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
CAUTION
The instructions shall state the substance of the following :
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of least resistance for electric current. This
appliance is equipped with a cord having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet that is installed and grounded in
accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service representative if you are in doubt
whether the appliance is properly grounded. Do not modify the plug provided with the appliance;
if it will not fit the outlet have a proper outlet installed by a qualified electrician.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product
it means the product is covered by the European Directive
2002/96/EC.
2. All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will help prevent
potential negative consequences for the environment and human
health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
4
I
NSTALLATION INSTRUCTIONS
WARNING
A qualified electrician/plumber or competent person should carry out any electrical/plumbing
work required to install this appliance.
Step 1 :
PREPARE CUPBOARD OPENING
Step 2 :
PREPARATION FOR ELECTICAL WIRING
CAUTION
1 This dishwasher is designed to fit the size
shown as below.
For personal safety, remove house
fuse or open circuit breaker before
installation. Do not use an extension
cord or adapter plug with this
appliance. Electrical and earthing
connections must comply with the
national electrical code/provincial and
municipal code and/or other local
codes.
2 Select a location as close to sink as
possible for ease of connection to the
water and drain pipes.
3 To ensure good drainage, the dishwasher
should not be installed more than 3 meters
away from the sink.
4 If dishwasher is installed in a corner, a
minimum of 5cm of space is required
between the washer and an adjacent
cabinet or wall.
1 This appliance must be supplied with
correct rating voltage and hertz as shown
on instruction manual, and connected to
an individual, properly earthed branch
circuit, protected by a minimum 15 amp
circuit breaker or time delay fuse.
Wiring must be 2 wire with Earth.
2 The power plug must be in a accessible
location adjacent to and not behind the
dishwasher and within 1.2 meters of the
dishwasher side.(See page 7 Fig.A)
3 The power plug must be correctly
earthed, if in doubt, have it checked by a
qualified Electrician. No other appliance
should be connected to the same plug
outlet by a double adapter or similar
plug.
Dangerous voltage
Unit:mm
To indicate hazards arising
from dangerous voltages.
Note – In case of application
in a warning sign the rules
according to ISO 3864 shall
be adhered to.
Any bare wood surrounding the
dishwasher should be sealed with a
waterproof paint or sealant to prevent
swelling.
5
I
NSTALLATION INSTRUCTIONS
Step 3 :
PREPARING THE DISHWASHER
FOR INSTALLATION
Step 4 :
INSTALLING THE
DISHWASHER IN CUPBOARD
1 Lay the dishwasher on its back.
1 Before sliding the dishwasher into the
cupboard opening, all necessary height
and balancing adjustments should be
made using a spanner.
2 Adjust the legs to the required height
as shown in below figure.
2 Slide the dishwasher into the cabinet
opening carefully. Make sure that the
drain hose inside the cabinet is not
kinked or stretched.
Adjust
leg
CAUTION
If the height of the cupboard is below
850mm, you should remove the top table
by unscrewing the 2 screws. (Two of rear)
6
I
NSTALLATION INSTRUCTIONS
Step 5 :
DRAIN LINE CONNECTION
When the drain hose is connected to a
separate standpipe, it is essential that an
airtight connection be made.
Refer to Fig.B
1 If the end of drain hose does not fit to
the drain line, use a rubber
connector(not supplied) that is
resistant to heat and detergent.
2 This should be available from a
plumbing shop or DIY merchants.
3 There are two typical connections as
shown in Figure A, B.
The “S” trap spigot must be drilled out
cleanly and free of obstruction to its
maximum internal diameter, if used for
drainage.
Fig. B : Drainage connection - stand pipe.
To prevent siphoning, one of the following
methods must be used:
Drain hose Extension
When the drain hose is connected to a
sink “s” trap or waste disposal unit, the
hose must be looped up to the underside
of the bench top and secured.
Extend drain hose as shown below.
CAUTION
Fig. A
When you connect or extend drain hose,
make sure that drain hose is not kinked.
(Bends should have a 40 mm radius.)
7
I
NSTALLATION INSTRUCTIONS
Step 6 :
WATER SUPPLY CONNECTION
Step 8 :
HOW TO LEVEL THE DISHWASHER
1 Connect the water supply hose to the
water tap as shown.(Some models
consist of an inlet valve and hose.)
This dishwasher may be fed with either
hot or cold water. If the water can not be
maintained below 65ºC, the dishwasher
must be connected to cold water.
After installing the dishwasher, you may
notice a slight sticking of the door to the
dishwasher, when you open or close the door.
If this does happen you need to adjust the level
of the dishwasher.
Case 1. In case the door is slanted to the right
2 When connecting, the sealant tape or
sealing compound to avoid water leaks.
Make sure that the line is not kinked or
sharply bent.
The new hose-sets supplied with the
appliance are to be used and that old
hose-sets should not be reused.
Fig. C
• If the door slants to the right, see fig, C and
follow these instructions:
1) Unscrew(counter-clockwise) the left leg of
the back side and correct the level.
2) Check the opening of door and repeat if
necessary until the door opens and closes
properly.
• When the product is correctly leveled, There
should be no slant , stickiness or friction
sound.
Water tap
Water supply
hose
Case 2. In case the door is slanted to the left
Step 7 :
FINAL CHECK AND ASSEMBLING
1 Securely hand tighten supply hose to the
water supply.
Plug the power supply cord into an earthed
electrical point and switch on.
Fig. D
2 After installing and prior to using the
dishwasher with crockery, we recommend
that you use the dishwasher on ‘Quick’
mode to rinse through. At this stage it is
useful to ensure that there are no operating
problems or water leaks.
When the dishwasher is used for the first,
there may be a loud noise, if this happens,
turn off the power and restart the
dishwasher.
8
• If the door slants to the left, see fig. D and
follow these instructions:
1) Check the opening of door if there still
remains sticky or friction sound.
2) Check the opening of door and repeat if
necessary until the door opens and closes
properly.
• When the product is correctly leveled, There
should be no slant , stickiness or friction
sound.
P
ARTS NAME
1. Control Panel
2. Door Handle
3. Front Cover
4. Lower Cover
5. Display Window
6. Power Button
7. Drain Hose
8. Inlet Hose
9. Power Cord
10. Adjustable Leg
11. Upper Rack
12. Cutlery Basket
13. Detergent And Rinse Aid Dispenser
14. Vapor Vent Cover
15. Upper Spray Arm
16. Lower Spray Arm
17. Filter ASM
18. Lower Rack
19. Salt Container Cap
Funnel
The appearance and specifications may vary without notice.
9
F
UNCTION OF CONTROL BUTTON
MODEL : D1423W(L,M,T,B,C,D,A)F(B,U)
Program
MODEL : D1422W(L,M,T,B,C,D,A)F(B,U)
WZ-6807WFL / WZ-6807MFL
Program
10
UV
Indicator
Time Left
Delay Start
Cool Dry
Indicator
Time Left
Delay Start
Beep On/Off
Spray
Beep On/Off
Spray
11
Rinse
Power
Rinse
Power
Half Load
Child Lock
Half Load
Child Lock
F
UNCTION OF CONTROL BUTTON
Program
• When you want to select program, press this button.
UV
• If you want to sterilize the dishes, press UV button.
• After drying cycle, sterilizer will be performed by UV lamp.
• At this time, “St” code is displayed in display window.
• When you open the door of dishwasher, UV lamp is turned off.
Don’t look at the lamp directly with the naked eye.
Cool Dry
• When you want better drying performance, press this button.
• This process is not part of the program.
• After drying cycle, the fan will operate for a few more minutes to diminish any remaining moisture.
At this time, “Cd” code is displayed in display window.
• If you want, you can open the door and unload the dishes at any time.
Indicator
• Child Lock.
• Refill with special salt.
• Refill with rinse aid.
Time Left
• Before starting, the display window shows the running time of the selected program.
• After starting, the display window shows the remaining time.
• If the dishwasher has a trouble, the trouble type is displayed.
“OE”, “FE”, “IE”, “EI”, “HE”, “CE”, “LE”, “tE”
• If this error letters are displayed, please refer to the trouble shooting guide page 25 and follow the guide.
Beep On/Off
• The dishwasher must be switched on.
• The beep on/off function can be set by pressing the Half Load and Spray button simultaneously for a
few seconds. Then, a “On” will appear in the display.
• The beep on/off function is automatically canceled when power failure occur.
Rinse
• Repeated pressing of the Rinse button will select Extra Hot, Rinse+, Extra Hot & Rinse+.
• If you select the Extra Hot function, the operating temperature will be up to 80 . (Dual wash, Auto, Eco)
• When you select Rinse + an additional rinse cycle is added.
Half Load
• In case of small load, use upper or lower rack only to save energy.
• With each press, can select Upper or Lower rack only.
• In case you don’t select this button, the machine always works vario washing, which operate upper and
lower spray arm alternately.
Child Lock
• Used to lock or unlock the control buttons to prevent all the setting from being changed by a child.
• This function is automatically canceled when power failure occur.
• For locking/ unlocking, press Half Load and Rinse button for a few seconds simultaneously.
Power
• For operating, press this button first for power on.
• After operating, this button automatically switches off for safety and energy saving.
• In case of irregular surge disturbance to the machine, the power may be automatically turned off for safety.
Spray
• With each press, the level of water jet is changed to Strong, Medium and Soft in a sequence.
Delay Start
• If you want to delay the start of selected program, press this button.
• Pressing this button will increase time by 1 hour.
• The delay start time can be adjusted from 1 hour to 19 hours.
12
B
EFORE USING FOR THE FIRST TIME
Hardness setting
You have to check your water hardness and set the softening system level before
operating your dishwasher.
< Water hardness level >
Step 1. Check and find water hardness level
Method 1
1) Check the water hardness of your area.
(Your water utility company can help you with this.)
2) Set the softening system level of your dishwasher
according to the water hardness level.
Refer to the Step 2.
(*L : Softening system level)
Method 2
1) Check your water hardness by using test strip. (
)
2) Test Procedure
Immerse all reaction zones of the test strip for approx.1sec (not in running water!).
Shake off excess liquid from the strip and wait for 1min.
Then, the green color of the reaction zone will change to the red-violet.
Count the number of red-violet from the strip.
< Water hardness level >
Number of
the areas
(red-violet)
Hardness range
°d
°e
°f
mmol/l mg/l
(Ca+Mg) Ca
Water
quality
<7
<9
<12,5
<1,3
<50
soft
7 - 14 9 - 17,5 12,5 - 25 1,3 - 2,5 50 - 100 moderately hard
hard
14 - 21 17,5 - 26 25 - 37 2,5 - 3,8 100 - 150
>21
>26
>37
>3,8
>150
very hard
Softening
system
level
H0, H1
H2, H3
H4, H5
H6, H7
1 °e = 14.25 mg/l CaCO3
1 °f = 10 mg/l CaCO3
1 °d = 10 mg/l CaO (=1,78 °f) (=1,25 °e)
3) Set the softening system level of your dishwasher according to the water hardness level.
Refer to the Step 2.
Step 2. Setting up the softening system level of your dishwasher
Adjust the water softener to the setting to the corresponding hardness of the water in your area.
The water softener has 8 adjustment levels.
The dishwasher is programmed at the factory for a water hardness level of “ ”.
This can be checked and altered by using the buttons on the control panel.
1. First, ensure the dishwasher is switched off.
2. Press UV(Cool Dry) and Power button simultaneously and keep them pressed.
3. To change the setting:
Simply press the UV(Cool Dry) button, then the figure will change one by one.
The display will change between “ ” and “ ”.
4. Once the hardness setting is correctly adjusted, press the Spray button.
The hardness setting is then saved.
13
B
EFORE USING FOR THE FIRST TIME
Step 3. Salt Filling
This model has a water softener to soften hard water.
Please read these notes carefully for correct operation.
In order to provide satisfactory rinsing results, the dishwasher requires soft water, i.e., containing
little or no lime, otherwise water stains will be left behind on the dishes and interior containers.
If the tap water exceeds a certain level of hardness, it must be softened, I.e.,decalcified.
This id achieved by adding a special salt to the water softener inside the dishwasher.
The required amount of salt is set up according to how hard your tap water is.
Filling with Salt
• Remove lower rack and unscrew the cap of salt container.
• Before using your dishwasher for the first time, fill with salt.
The container has a capacity of 1.9kg salt.
Use a funnel for ease and clean filling, ensuring that coarse salt
or regenerating salt intended for dishwashers is used.
• After filling, wipe off any spilled salt to seal the cap properly.
• Screw the cap tightly to prevent any suds from penetrating into
the container.
Step 4. Adding Rinse Aid
For filling
To fill the Rinse Aid chamber, rotate the round cap counter clockwise and remove. Fill the container
to the maximum level with a good quality Rinse Aid, then replace and lock the cap.
The Rinse Aid is automatically dispensed during the final rinse cycle.
The dosage is factory set to suit most installations. If, after washing, you notice cloudy spots, streaks
or water marks on your glassware, it may be necessary to increase the setting. To do this, remove the
cap and rotate the indicator arrow to a higher setting then replace the cap . If the glasses are smeared
or foam is present on the bottom of the glass or the bottom of the machine, select a lower setting.
14
H
OW TO USE AND OPERATE
How to use
[D1423W(L,M,T,B,C,D,A)F(B,U)]
1. Loading your Dishwasher
For better washing performance, always load
the dishwasher according to the instructions.
Before loading items into the dishwasher clean
off large particles of food, in particular
insoluble items such as bones, pips, etc.
When loading the dishwasher, please act
accordingly:
Position crockery such that water will
contact all surfaces.
Deep based items should be placed at an
angle to help water run off and dry properly.
Items with burnt on food should be soaked
prior to loading in the dishwasher.
Fold-down dividers at the lower and the upper
rack can be lowered to improve stacking of
pots and pans.
Loading examples (Energy test)
c
d
d
e
d
g
d
2. Loading the Lower Rack
f
The lower basket is best loaded with dinner
plates, soup bowls, dishes, pots, pans, lids and
even the grill tray.
Plates should be positioned upright and facing
the centre of the rack and pots, pans and large
dishes must be turned upside down.
d
a
d
g
How to use
[D1422W(L,M,T,B,C,D,A)F(B,U)
WZ-6807WFL / WZ-6807MFL]
f
Milk
Egg
d
b
e
e
Tea
Oat
c
f
Meat
Spinach
Margarine
Take care not to obstruct the rotation of the
spray arms and ensure that large items do
not prevent the detergent dispenser lid from
opening.
15
H
OW TO USE AND OPERATE
3. Using the Cutlery Basket
Loading examples (Energy test)
Cutlery should be mixed within each section
of the cutlery basket to prevent nesting of
similar items. Place the cutlery in the cover
with the handles down. The cover can be
hinged and clipped away from the basket if
you choose not to use them.
Place knives in the separate rack for located in
the top of the dishwasher.
Take care when loading and unloading
sharp items.
How to use
3
3
3
4
4
4
4
3
3
1 2 3 4 5 6 7
Slide two baskets in opposite directions, then
pull them apart.
3
3
4
1
1
1
1
1
1
1
2
2
2
2
2
2
2
5
7
4
4
4
4
4
1
1
1
3
6
3
1
1
1
1
2
2
2
2
2
2
2
5
3
4
4
4
4
3
3
3
3
WARNING
Knives and other utensils with sharp
points must be loaded in the basket with
their points down or placed in a
horizontal position.
16
H
OW TO USE AND OPERATE
4. Loading the Upper Rack
Loading examples (Energy test)
It is best to load this with more delicate items
such as, small plates, long cutlery, cups, glasses
and dishwasher safe plastic items. Plates should
be positioned upwards with the plate bottom
facing the front of the rack.
Cups, glasses and bowls must be positioned
upside down.
Extra cups or cooking utensils can be laid on
the fold down cup racks, which also provides
support for long stem glasses.
Take care not to obstruct the rotation of the
spray arm under the upper rack.
d
c
b
a
How to use
[D1422W(L,M,T,B,C,D,A)F(B,U)
WZ-6807WFL / WZ-6807MFL]
b
a
d
g
Milk
Egg
b f
b
e
Tea
Oat
f
c
f
Meat
Spinach
Margarine
Non Dishwasher Safe Items
The combination of high water temperatures and
dishwasher detergent may damage particular items,
therefore we do not recommend using the
dishwasher to wash the following:
Copper or anodized aluminum
Hand painted silver or gold leaf crockery
Wood or bone handled utensils
Iron or non rust proof utensils
Plastic items that which are not dishwasher safe.
How to use
[D1423W(L,M,T,B,C,D,A)F(B,U)]
Fold-down dividers at the upper rack can be
lowered to improve stacking of dishes.
17
H
OW TO USE AND OPERATE
5. Adjusting the Upper Rack
WARNING
Before adjusting, ensure the rack is
empty of all crockery.
Otherwise crockery may be damaged
or you may be injured.
Your upper rack can be raised or lowered to
cater for different sized crockery. Before
adjusting, ensure that the rack is empty.
You can change the position of the upper rack
by lifting the rack upward, into the upper
position, or by pulling on the two levers on
either side of the rack to move it down to its
lower position.
6. Adding Detergent
• Detergent must be put into the detergent
chamber before starting every program except
the Pre Wash.
• Please follow the manufacturer’s instructions
within the manual, when determining the correct
amount of detergent to use.
• If your dishes are moderately dirty, you may use
slightly less detergent than recommended.
• Chambers hold 15g and 25g.
• The amount of detergent required depends on
the program. Please refer to the guide table.
We recommend that where possible the upper
rack remains level.
And when you pull the rack upward, hold the
middle location of the upper rack
(
marked position)
After adjusting the rack levels, check
that the spray arm is free to rotate.
PROGRAM
AMOUNT OF DETERGENT
Dual Wash
25g
Auto
20g
Eco
15g
Gentle
15g
Quick
10g
Pre Wash
No detergent
• After the detergent is supplied, the chamber
lid should be closed.
• The detergent is dispensed automatically
during the operation.
• The chamber lid remains open after
operation.
Detergent Information
Use only the detergent intended for
household dishwashers. (Ordinary handwashing detergent should not be used,
because the foam can interfere with proper
operation.)
18
H
OW TO USE AND OPERATE
7. Refilling
Push latch to open
For refilling Rinse Aid
Depending on the dosage setting and the
number of washes, the chamber may need to
be topped up, approximately once a month.
The rinse aid level can be checked by two
methods.
• By the indicator window on the dispenser
when the dishwasher door is fully open.
Black indicates sufficient Rinse Aid
Clear indicates Rinse Aid required
Place proper
detergent into this
compartment
WARNING
The detergent used is a special
Dishwasher detergent and like all
household chemicals it should be
treated as harmful and kept out of
reach of children. After completion of
the wash program, the detergent
compartment should be checked and
any remaining detergent removed.
• By the light on the control panel, being lit,
when the dishwasher is working on.
When the lamp is lit, it means the rinse
aid is almost empty. Refill the Rinse Aid
chamber as soon as possible.
ATTENTION
Using combined detergent products
(ex.3 in 1)
Some products integrated rinse aid
work best specific programs only.
Yow will obtain optimum rinsing and
drying results by using conventional
and separate salt and rinse aid.
Products that replace regeneration salt
can only be used within a specific
water hardness range.
Please contact the detergent
manufacturer if the drying performance
is very poor or you find the white film,
when you use the combined detergent
products.
We do not warrant the complaints that
are directly related to the use of these
products.
Rinse Aid Information
Rinse Aid is necessary to remove spots and
streaks from dishes as well as improved
drying. Using the correct amount will improve
wash performance. However, using too much
can produce excess foam leading to possible
water leaks.
19
H
OW TO USE AND OPERATE
8. Drying
For refilling Salt
When the salt container is empty, the salt refill
lamp will automatically turn on during
operation. The salt should be refilled after the
cycle has finished. We recommended the salt
refill should always be carried out, as
mentioned previous page, prior to starting the
next operation. This will immediately thin and
drain away any excess salt solution.
To assist drying, we recommend that the
door be fully opened after the cycle.
9. Energy Test(EN50242)
Appliance loaded in accordance with
standard specifications.
• Example of loaded dishwasher : p.15~17
• Capacity : 14 place settings
• Comparability course : Eco
• Rinse Aid setting : 4
• Reference cleaner : 8g of detergent onto the
inside surface of the door and fill 27g into
the detergent dispenser.
• Height-adjustable Rack-U must be inserted
into the uppermost position.
When the lamp is lit, this means that the
salt aid is almost empty. Refill the Salt
Aid chamber as soon as possible.
Note
• After filling with salt, it may take a little
while before the indicator light turns off.
• When the control is set to “ ”, it is not
necessary to fill up with salt as no salt is
consumed while the dishwasher is
operating. If the control is set between
“ ” and “ ”, then salt must be added
to the dispenser.
WARNING
Do not pour detergent into the salt
container. This will destroy the water
softener.
20
O PERATING SEQUENCE
The corresponding indicator lights will
illuminate if refilling is required.
The time in the display window will start
to decrease minute by minute.
If the door is opened during the program
a safety device ensures that the machine
stops.
Once the door is re-closed the program
will start from where it was interrupted.
Open the door and check
the filters
At the end of the
washing program
Ensure they are clean and properly
positioned (See “User Maintenance
Instructions”).
“End”is displayed on the digital display
and a buzzer sounds.
And the dishwasher automatically
switches off for safety and energy saving
later.
Press the “Power” button
Check there is rinse aid
and salt
Load the dishes
If you select “UV” function, the dishwasher
automatically switches off after sterilizing
action.
Remove any excess food.
Pull the lower rack out and arrange the
dishes and cutlery.
Pull the upper rack out and arrange the
cups, glasses, etc.
If you selected “Cool Dry” function, the
display then shows “Cd” to indicate that
the dishwasher is in “Cool Dry” mode.
And then the dishwasher automatically
switches off later.
CAUTION
Do not load the items in upper rack with
the lower rack is pulled out and loaded.
CAUTION
Empty the lower rack first and then the
upper one;this will avoid water dripping
from the upper rack onto the dishes
below.
Ensure the spray arms can
freely rotate
Measure out detergent
Add the required amount of detergent into
the dispenser and close the lid.
WARNING
In general it is not advisable to open
the door while the machine is working.
If the door is opened, a safety device
ensures that the machine stops.
Care must be taken if the door is
opened during the hot phase or
immediately after a program has
finished, as steam may escape.
Setting and starting the
program
Press the program button to select the
desired program.
After 5 seconds, the machine will start.
If necessary, select the option function
corresponding to the desired program.
The indicator lights of the program and all
the phases of the program will come on.
Before starting, the display window shows
the running time of the selected program.
After starting, the display window shows
the remaining time.
CAUTION
That the door should not be left in the
open position since this could present a
tripping hazard.
21
P
ROGRAM
Running time may vary according to the water temperature, water pressure and voltage.
Running time doesn’t include “Cool Dry - 30min”.
Program
Dual Wash
Auto
WASH
Pre Wash Main Wash
40
RINSE
Rinse 1
Rinse 2
Rinse 3
60
Heating
Rinse
DRY
COOL
DRY
70
The program sequence is optimized and adapted in accordance with how dirty the
dishes are.
Eco
Gentle
Quick
43
60
45
70
50
50
65
Pre Wash
Dual Wash
and water consumption for a good washing
performance. It is recommended that it will be
used every time.
This program is ideal for very dirty crockery, in
particular pots, pans and casserole dishes.
This program will be able to control the water jet
level of each spray arm differently.
Gentle
This program is for washing delicate items like
glasses.
Auto
During the Auto program, the degree of soiling
in the dishes is determined by the amount of
clouding of the water.
According the degree of soiling, the program
automatically adjust the washing time,
temperature. As a result, the energy and water
consumption is kept as low as possible. The “F”
on display means that the sensor is sensing the
status of the dishwasher.
Quick
Can use for lightly soiled recently used dishes
and cutlery.
When you select “Quick” program, After
finishing, “Cool Dry” function is automatically
performed for the better drying result.
Pre Wash
Eco
Can use this program for only removing soil
before washing dishes by hand.
This program offers the most efficient energy
Auto Restart
If the dishwasher is turned off by a power failure, it will restart from the position it stopped at
adjusting accordingly when you press the Power button again.
22
U
SER MAINTENANCE INSTRUCTIONS
To prevent trouble and poor operating, it is important to check filters and spray
arms at regular intervals.
Filters
Lower Spray Arm
• Remove the lower rack first.
• Turn the mesh filter counterclockwise.
• Take out the mesh filter, upper STS filter
and outer filter.
• Clean them if necessary.
• Replace them in the reverse order.
• Check that the water jet holes are not
blocked.
• If cleaning is required, remove the arm by
pulling up.
• Clean the spray arm and replace it pulling
down.
mesh filter
upper STS filter
outer filter
Upper Spray Arm
• Pull the upper rack forwards.
• Check that the water jet holes are not
blocked.
• If cleaning is required, remove the arm by
unscrewing the nut.
• Clean the spray arm and replace it in the
reverse order.
After each cycle, clean the filter for
the better washing result.
Before starting, check that the filter is
assembled well. If the filter is not
assembled correctly, you might have
a poor cleaning result.
23
T
ROUBLE SHOOTING GUIDE
If a problem occurs check below to see whether this can be solved.
In the unlikely event that the problem cannot be rectified, please contact a
service engineer.
Problem
Possible Causes
Solution
No lights come on when
the power is turned on.
• Plug is not properly inserted into
the socket.
• Fuses blown or circuit breaker
tripped.
• The electricity of the house was
cut off.
• Check the plug.
• Check the electricity.
• Call for service.
The machine does not
start.
• Door is not fully closed.
• The start button is not pressed.
• Close the door.
• Press the start button.
The spray arms do not
rotate smoothly.
• The mounting of the spray arms is
blocked by food particles.
• Clean the holes of the
spray arm.
White deposits are left
on the dishwasher after
washing.
• The amount of detergent or rinseaid set incorrectly.
• The salt container is empty.
• The salt container cap is not
securely screwed on.
• Check the detergent
or rinse-aid.
• Check the salt
container or cap.
Streaks are left on
glassware.
• Too little Rinse-Aid dispensed.
Dry results are not
satisfactory.
• Too little Rinse-Aid dispensed.
Washing results are not
satisfactory.
• Incorrect amount of detergent.
• Utensils incorrectly arranged or
overloaded.
• Filters are clogged.
• Water jet holes of spray arms
blocked.
• Spray arm's rotation obstructed by
utensils.
• Unsuitable program selected.
24
• Fill the rinse-aid.
• Adjust the level of
rinse-aid container.
T
ROUBLE SHOOTING GUIDE
Problem
Possible Causes
Solution
The display shows "OE"
code. (Water is not
pumped away.)
• The drain hose is kinked.
• The filter is clogged.
• Motor trouble.
(Washing motor or Drain motor)
• Straighten hose(s).
• Clean the filter.
• If you can not solve
the problem, call for
service.
The display shows "IE"
code.
• Water is not supplied.
• Water tap is not opened.
• Water sensor has a trouble.
• Check the water tap.
• If you can not solve
the problem, call for
service.
The display shows "EI"
code.
(Automatically Drain
pump operated.)
• Water is leaking from the hose
connections.
• Damage to the unit has been
caused by a water leak.
The display shows "FE"
code. (Automatically
Drain pump operated.)
• Excessive water is supplied than
the normal water level.
• There is a problem with the inlet
valve.
The display shows "HE"
code.
• The water heater circuit is damaged.
The display shows "tE"
code.
• Thermistor trouble or very high inlet
water temperature.
The display shows "LE"
code.
• Motor trouble.
The display shows "CE"
code.
• Motor trouble.
25
• Close the water tap
and unplug the power
plug.
• Call for service.
M EMO
26
M EMO
27
D1422W(L,M,T,B,C,D,A)F
D1423W(L,M,T,B,C,D,A)F
WZ-6807WFL / WZ-6807MFL
D1422W(L,M,T,B,C,D,A)B
D1423W(L,M,T,B,C,D,A)B
600mm
598mm
600mm
567mm
850mm
819mm
D1422W(L,M,T,B,C,D,A)U
D1423W(L,M,T,B,C,D,A)U
598mm
567mm
819mm
P/No.: MFL62077145
Capacity
14 Place settings
Weight
See rating label
Power Supply
See rating label
Power Consumption
See rating label
Water Feed Pressure
50 ~ 800 kPa
Download PDF