LG | LND5100 | LG LND5100 Owner's manual

CAUTION
Warning: Do not install this equipment in a
confined space such as a bookcase or similar
unit.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
OWNER'S MANUAL
High Definition Network Dome
Camera
Please read this manual carefully before operating
your set and retain it for future reference.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.
•
Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.
•
Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.
MODEL
LND5100 series
This Class A digital apparatus complies with Canadian ICES-003.
AB28
LND5100 series
Image Device
6.08 mm (1/3 type) Progressive Scan CMOS
(1.3 Mega Pixels)
Lens Type
2.8 mm to 10 mm F1.2
Minimum
Illumination
ICR
Color
Warning: To reduce a risk of fire or electric
shock, do not expose this product to rain or
moisture.
Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.
3.
Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.
Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
4.
To disconnect power from mains, pull
out the mains cord plug. When installing
the product, ensure that the plug is easily
accessible.
LG Electronics hereby declares
that this/these product(s) is/are
in compliance with the essential
requirements and other relevant
provisions of Directive 2004/108/
EC and 2011/65/EU.
Contact office for compliance
of this product :
LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The
Netherlands
When this crossed-out
wheeled bin symbol is
attached to a product
it means the product is
covered by the European
Directive 2002/96/EC.
All electrical and electronic
products should be
disposed of separately from
the municipal waste stream
via designated collection
facilities appointed by the
government or the local
authorities.
The correct disposal of
your old appliance will help
prevent potential negative
consequences for the
environment and human
health.
For more detailed
information about disposal
of your old appliance,
please contact your city
office, waste disposal
service or the shop
where you purchased the
product.
EEE Compliance with Directive.
(for Turkey only)
Important Safety
Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8.
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
Integrated Client
LVi510
a Dome Cover
Remote S/W
LVi510, Mobile application (iPhone, Android, iPad)
b Lens Cover
Connections
Up to 10
Security
Password Protection, HTTPS(SSL, TLS), IEEE 802.1X
Ethernet
10/100 Ethernet
0.3 lx (F1.2, Sens-up off )
0.01 lx (F1.2, Sens-up x60)
B/W
2.
Part Names and Functions
Item
Day/Night
1.
Warning: This is a class A product. In a
domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Specification
Disposal of your old appliance
Protocol
0.005 lx (F1.2, Sens-up off )
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
a
ONVIF 2.2 Profile S, PSIA 1.1
Operation Temperature/Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Image Enhancement
Backlight Compensation, 2D+3D-DNR, Exposure
Control, Sens Up Control, AGC, White Balance,
Privacy Masking, EIS, Sharpness, Digital Zoom,
Scene mode
Power Source
PoE, DC 12 V
e Tilting lock screw
Power Consumption
5.9 W
Input current
DC 12 V
Maximum 440 mA
f Pan adjuster
Adjusts the pan position.
PoE
Maximum 140 mA
Output
RJ-45 (Network), RCA (Installation)
Frame Rate (Maximum)
30 fps @ 1 280 x 1 024, 30 fps @ 720p
Compression
H.264_HIGH, H.264, MJPEG
Multi-Streaming
Dynamic Profile (Up to 7)
ROI (Region of Interest)
Support
Audio In/Out
1/1
Audio Compression
G.711, G.726
2-way Audio
Support
SD Slot
Micro SD
EVENT
Alarm In/Out
1/1
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Dimension (Ø x H)
140 mm x 120 mm
Weight
610 g
•
Use a dry soft cloth to clean the body. If it
is very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.
•
Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.
•
This camera is designed for mounting
on the ceiling or wall. If you install this
camera upside down, it may cause
malfunction.
Operating and storage
location
Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.
•
•
•
•
•
•
Extremely hot or cold places (operating
temperature -10 °C to 50 °C, however, we
recommend that the unit be used within
a temperature range of 0 °C to 45 °C)
Damp or dust place
Places exposed to rain
Places subject to strong vibration
Close to generators of powerful
electromagnetic radiation such as radio
or TV transmitters.
Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates the need
for power outlets at the device locations and enables easier application of uninterruptible
power supplies (LPS).
b
Open Protocol
Up to 1 280 x 1 024
Remove dust or dirt on the surface of the
lens with a blower.
NOTE:
Support
Resolution (Maximum)
•
d ETHERNET/PoE Port
Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached
RJ-45 connector.
0.000 1 lx (F1.2, Sens-up x60)
Motion detection, Intelligent motion detection, Trip
zone, Object counting, Streaming metadata
Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to
fail or to get cause of fire or electric shock.
c Azimuth adjuster
WDR
Video Analytics
Handling of the unit
c
d
e
f
g
h
i
j
k
l
m
g RESET button
Push the button more than 3 seconds, this would restore the factory default network
related settings.
h micro SD card slot
Insert the micro SD card.
i ALARM IN / ALARM IN RETURN
Provides physical interface for sensor.
ALARM OUT / ALARM OUT RETURN
Provides physical interface for Alarm/Relay.
j AUDIO OUT (Line Level Output)
k AUDIO IN (Line Level Input)
l Power input terminal
Connects to a DC 12 V power supply using proper cables. This camera must always be
operated a DC 12 V. Certified/Listed Adaptor which comply with LPS.
m Camera mounting bracket
ETHERNET
With PoE
Connection
Precautions
Connecting Power Source
Connecting Alarm Device
•
Be sure to switch off the unit before
installation and connection.
Connect power, using one of the methods
listed below:
•
The installation should be made by
qualified service personnel or system
installers.
To use the power adapter
Alarm terminals are used to connect the
alarm (relay) devices such as sensors, door
switches, etc.
•
Do not expose the power and
connection cables to moisture, which
may cause damage to the unit.
Connect a DC 12 V power source to the
power input terminal as shown below.
(recommended power adapter is DC 12 V/1.5
A or above)
Connecting Network
You can control and monitor the system
via network. With the remote control
(monitoring), you can change the system
configuration or monitor the image via
network. After the installation, check the
network settings for the remote control and
monitoring work.
Connect the IP camera to your network using
a standard RJ-45 network cable as shown
below.
ALARM IN / ALARM IN RETURN (Sensor
Input)
Connect the alarm (relay) device to the relay
output terminal. Alarm signal is outputted at
an event occurrence.
Connecting Microphone
and Speaker Device
GREEN
BLACK
AUDIO IN
Transcend
Sensor Device
To use the PoE (Power over Ethernet)
device
GREEN-ALARM IN
BLACK-ALARM IN
RETURN
RED-ALARM OUT
WHITE-ALARM
OUT
RETURN
Alarm (relay)
Device
WHITE
NOTE:
The Photo MOS Relay is rated for 100 mA at
20 V DC or 100 mA at 28 V AC.
ETHERNET
With PoE
AUDIO OUT
NOTE:
Keep the microphone away from the speaker
to avoid howling.
Using the micro SD card
You can record your surveillance environment
with the micro SD card even if the network is
disconnected condition.
NOTES:
•
Do not use the power too much when
you insert the micro SD card. The micro
SD card may be damaged.
•
Router
1.
Remove the Dome Cover.
2.
Insert the micro SD card carefully as
shown in the following illustrations.
Make sure the micro SD card terminal
position before insert the micro SD card.
Push the back end of the micro SD card
to fix it at the last step.
NOTE:
If the camera doesn’t work properly after
connecting PoE device, please check if the
PoE device supplies enough power.
If you insert the micro SD card in the
wrong position, the micro SD card
may be damaged or it may cause the
malfunction of the micro SD Card Slot.
•
Keep the terminal part of the micro SD
card in clean. Be careful the terminal part
of the micro SD card not to dusty.
•
As the micro SD card is consumable, the
micro SD card end its days and may be
not able to save data if you use it more
than over certain times. In this case,
replace micro SD card to buy a new one.
To insert the micro SD card
PoE Device
(IEEE802.3af )
Remove the micro SD card
1.
2.
Take the micro SD card out carefully from
the camera. It may cause a malfunction
of the micro SD card or the micro SD
card slot if you use the power too much
at lock status.
CAUTION:
•
If you install the micro SD card on the
camera and remove with the micro SD
card condition indicator lights on, you
must unmount the micro SD card by
using the [System > Storage > Device
Management > Unmount] menu. The
micro SD card data is compromised or
the camera may not operate normally,
if you remove the card without use
[Unmount] function.
•
LG Electronics is not responsible for
deleted data caused by user mishandling
when you insert or remove the micro
SD card.
Press the back end of the micro SD card
to release the lock condition.
PAN
Follow the instructions below to install the camera with camera mounting bracket.
1.
3.
Connect the cables to the cable jacks of the camera body.
Use the installation guide template to check the mounting location. Face the front of the
label toward the area of interest. Using the template as a guide, make a hole through the
ceiling.
NOTE:
To disassemble the camera from the mounting bracket, rotate the camera counterclockwise with
pressing the PUSH button inside the camera body.
2. Adjust the pan/tilt/rotation position of the camera.
TILT
ROTATION
PAN
CAUTION:
Install on a ceiling or wall where can withstand the weight of 5 times of the camera including
mounting bracket.
Camera Adjustment
1.
Connect the portable minitor to the video jack using the test monitor cable.
3. Adjust the zoom and focus.
Install the camera mounting bracket to the ceiling.
4.
Assemble the camera and mounting bracket after align the front part of the camera and
mounting bracket. Connect the unit by following step a and b.
FAR
Test monitor cable
n 10
77
68
FR
03
ON
T
ING
4 Pla SCRE
ce W
62
TA
PP
SELF
MEZ
FAR
NEAR
ION
SIT
SIT
PO
PO
ER
ER
NT
T CE
NT
T CE
UC
OD
PR
OD
UC
PR
CA
BL
CA E HO
BLE LE
HO (LCV
LE 53
(LCD 00
53 )
00
)
03
77
68
ION
SELF
MEZ
TA
62
FR
ON
T
PP
ING
4 Pla SCRE
ce W
n 10
0 Cu
0 Cu
t in
t in
g Li
ne
g Li
ne
TELE
CA
BL
CA E HO
BLE LE
HO (LCV
LE 53
(LCD 00
53 )
00
)
2.
TILT
ROTATION
POWER IN
DC 12 V
Mounting the camera
Capacity
Block Size
(FAT 32)
Less than
32 GB
32 kbyte
NOTE:
Speed of reading and writing more than
10 MB/Sec. (Class 6)
PoE Device
(IEEE802.3af )
Broadband
Service
LG
RED
NOTE:
When the connecting Alarm and Audio,
tighten the screws as shown above.
Broadband
Service
Maker
Sandisk
GREEN-ALARM IN
BLACK-ALARM IN
RETURN
RED-ALARM OUT
WHITE-ALARM
OUT
RETURN
POWER IN
DC 12 V
Recommended the micro SD card
specification
Optionally connect an active speaker and/or
external microphone with a built-in amplifier.
Connect the sensor device to the sensor input
terminal.
Connect the PoE cable to the LAN port on the
unit. You must use the “IEEE802.3af” standard
PoE device.
ETHERNET
With PoE
ALARM OUT / ALARM OUT RETURN (Relay
Output)
TELE
WIDE
NEAR
WIDE
Download PDF