Specification
Item
OWNER’S MANUAL
High
Definition
Network
Camera
Camera
Video
Event
Please read this manual carefully before operating
your set and retain it for future reference.
To view the instructions of advanced features,
visit http://www.lgecommercial.com and then download Owner’s Manual.
MODEL
LND3110R series
Network
LND3110R series
OPEN SOURCE SOFTWARE NOTICE
Power Source
DC 12 V
Maximum Power
Consumption
5.4 W
Maximum
Input Current
450 mA (DC 12 V)
Operation
Temperature/
Humidity
-10 ºC to 55 ºC / 0 % RH to 80 % RH
Digital (Dynamic Range Enhancer)
Dimension
(Ø x H)
140 mm x 122 mm
Image
Enhancement
Backlight Compensation, DNR, Exposure Control, AGC, White
Balance, Privacy Masking, Sharpness
Weight
465 g
Compression
H.264_HIGH, H.264, MJPEG
Resolution
1280 x 1024 / 1280 x 720 / D1 (704 x 480) / CIF (352 x 240)
Maximum
Frame Rate
30 fps @ 1280 x 1024
Multi-Streaming
Up to 2
Video Analytics
Motion detection, Tampering alarm
Event
Notification
Email, FTP
Pre Event
Buffering
Support
Ethernet
RJ-45 10 / 100BASE-T
Security
Password Protection, HTTPS(SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6: TCP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP,
QoS, UPnP
Image Device
6.28 mm (1/3 type) CMOS
Lens Type
4 mm F2.0
Day/Night
ICR (Auto / Day / Night)
Minimum
Illumination
Color: 0.03 lx @ F2.0 (1/30 sec, 50 IRE)
IR Distance
20 m
WDR
General
B/W: 0 lx @ IR LED on
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in
this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices
are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the
cost of performing such distribution (such as the cost of media, shipping and handling) upon email
request to opensource@lge.com. This offer is valid for three (3) years from the date on which you
purchased the product.
Note that design and specification of this unit may change from the manual as quality and improvement without prior notice.
Component
Camera, Installation Manual, Screws (4 EA), Installation sticker, Camera mounting bracket
Символ «не для пищевой
продукции» применяется в
соответствие с техническим
регламентом Таможенного
союза «О безопасности
упаковки» 005/2011 и указывает
на то, что упаковка данного
продукта не предназначена для
повторного использования и
подлежит утилизации. Упаковку
данного продукта запрещается
использовать для хранения
пищевой продукции.
Символ Кедендік одақтың
005/2011 техникалық
регламентіне сәйкес
қолданылады және осы
өнімнің қаптамасын екінші рет
пайдалануға арналмағанын
және жоюға жататынын
көрсетеді. Осы өнімнің
қаптамасын азық-түлік өнімдерін
сақтау үшін пайдалануға тыйым
салынады.
Символ «петля Мебиуса»
указывает на возможность
утилизации упаковки.
Символ может быть дополнен
обозначением материала
упаковки в виде цифрового и/или
буквенного обозначения.
Символ қаптаманы жою
мүмкіндігін көрсетеді. Символ
сандық код және/немесе әріп
белгілері түріндегі қаптама
материалының белгісімен
толықтырылуы мүмкін.
IPv4: FTP, SMTP, NTP, ARP, SNMPv1/v2c/v3, DDNS(LG)
*MFL69355806*
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad,
Android)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
•
Integrated
Software
Warning: Do not install this equipment in a
confined space such as a bookcase or similar
unit.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
•
Up to 10
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
•
Connections
A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.
Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.
Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Warning: This is a class A product. In a
domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.
Warning: To reduce a risk of fire or electric
shock, do not expose this product to rain or
moisture.
The Power Plug is the disconnecting device.
In case of an emergency, the Power Plug
must remain readily accessible.
Contact office for compliance of this product:
LG Electronics European Shared Service Center B.V.
European Standard Team
Krijgsman 1
1186 DM Amstelveen
The Netherlands
Disposal of your old appliance
1.
Warning: Please adopt the power adapter
which can meet the safety extra low voltage
(SELV) standard. And source with DC 12 V or
AC 24 V (depending on models) according
to the IEC60950-1 and Limited Power Source
standard.
Warning: Install the camera on a ceiling or wall
where can withstand the weight of 5 times of
the camera including mounting bracket.
2.
Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.
Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.
Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be placed
on the apparatus.
Caution: Make sure the power supply voltage
is correct before using the camera.
Caution: Do not drop the camera or subject it
to physical shock.
Caution: The sensor may be burned out by
a laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.
Caution: While shipping, the camera should be
packed in its original packing.
3.
This crossed-out
wheeled bin symbol
indicates that waste
electrical and electronic
products (WEEE)
should be disposed
of separately from the
municipal waste stream.
Old electrical products can contain
hazardous substances so correct disposal
of your old appliance will help prevent
potential negative consequences for the
environment and human health. Your old
appliance may contain reusable parts that
could be used to repair other products,
and other valuable materials that can be
recycled to conserve limited resources.
You can take your appliance either to the
shop where you purchased the product,
or contact your local government waste
office for details of your nearest authorised
WEEE collection point. For the most up to
date information for your country please
see www.lg.com/global/recycling
Important Safety
Instructions
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
8.
9.
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
Handling of the unit
Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the
lens with a blower.
•
Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.
•
•
Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.
This camera is designed for mounting on
the ceiling or wall. If you install this camera
upside down, it may cause malfunction.
Operating and storage
location
Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.
•
Extremely hot or cold places (operating
temperature -10 °C to 55 °C, however, we
recommend that the unit be used within a
temperature range of 0 °C to 45 °C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful
electromagnetic radiation such as radio or
TV transmitters.
•
Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.
Part Names and Functions
Connection
a Dome Cover
Precautions
Connecting Network
Connecting Power Source
b IR LED
• Be sure to switch off the unit before installation and
connection.
• The installation should be made by qualified service
personnel or system installers.
• Do not expose the power and connection cables to moisture,
which may cause damage to the unit.
You can control and monitor the system via network. With the
remote control (monitoring), you can change the system
configuration or monitor the image via network. After the
installation, check the network settings for the remote control
and monitoring work.
Connect the IP camera to your network using a standard RJ-45
network cable as shown below.
Connect a DC 12 V power source to the power input terminal as
shown below.
(Recommended power adapter is DC 12 V/ 1.5 A or above)
.
Do not stare at operating IR LED within hazard distances (1 m).
c IR Sensor
a
d Camera mounting bracket
You can lock the camera mounting bracket by tighten the screws.
,
b
c
To disassemble the camera from the mounting bracket, rotate the camera
counterclockwise with pressing the PUSH button inside the camera body.
,
Ethernet device
(IEEE802.3af )
e Power input terminal
Connects to a DC 12 V power supply using proper cables. This camera must always be operated
a DC 12 V. Certified/Listed Adaptor which comply with LPS.
Broadband
Service
fETHERNET
Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached
RJ-45 connector.
• When the connecting power adapter, tighten the
screws as shown above.
• Put your finger between the power connector and the
camera body to pull out the connector.
Router
g RESET button
Push the button more than 3 seconds, this would restore the factory default network related
settings.
Broadband
Service
d
e f
g
Installation
Mounting the camera
3.
Connect the cables to the cable jacks of the camera body.
4.
Follow the instructions below to surface mount the camera with supplied camera mounting
bracket.
1.
Assemble the camera and mounting bracket after align the front part of the camera and
mounting bracket. Connect the unit by following step a and b.
Camera Adjustment
Adjust the Pan/Tilt/Rotation position of the camera.
Use the installation guide template to check the mounting location. Face the front of the label
toward the area of interest. Using the template as a guide, make a hole through the ceiling.
ROTATION
PAN 270°
2.
TILT
PAN 90°
Disassemble the camera from the mounting bracket. Install the camera mounting bracket to
the ceiling.
,
• Be careful of sharp edge after removing the cap of cable conduit.
• Arrange the cables by cable tie after installation.
,
• When you assemble the dome cover, make sure the arrow of base bracket position is
aligned with the LG logo.
• Manual adjustment: PAN: 360° / TILT: 75° / ROTATION: 355°
• When you adjust PAN/TILT/ROTATION manually, be careful your hand is not to hurt by
protrusions of other part.
• When you adjust PAN/TILT/ROTATION manually, be careful the cable is not damaged or
pinched.
Download PDF

advertising