LG LP-XG2 Owner’s Manual

Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the bottom of the set and
quote this information to your dealer when you
require service.
Model number
:
Serial number
:
LGCDPROJET
LP-XG2
OWNER'S MANUAL
LCD
PROJECTOR
PROJECTOR
1
Safety
CONTENTS
Instructions
3
Names of parts
7
Installation and Connection
11
Desktop
PC
15
Connecting
to a
Connecting
to a Notebook PC
16
Connecting
to a Macintosh
PC
17
Connecting
to a Macintosh PowerBook
20
Desktop
Connecting
to a Video Source
21
Connecting
to a D-TV
22
the
Operating
Turning
on
Function
Box
Projector
the
Projector
source
mode
Still function
Using
Using
Before
operating
unit, please read
manual carefully.
the
this
time
30
Blank function
Selecting
PC
screen
size
screen
Using Tracking
Adjusting
input signal
display
function
Video
Supported
Monitor
31
33
Resize function
Adjusting
27
29
Horizontal / Vertical function
Using Flip
25
28
Selecting language
Checking lamp
23
26
checking
Selecting
Using
Settop
35
36
37
39
41
Display
42
Maintenance
43
Specifications
44
2
Instructions
Safety
Always keep
Safety
the
safety
instructions to
Instructions have two kinds of information, and each
WARNING
NOTES
The
prevent any potential accident
meanings
of
The violation of this instruction may
The violation of this instruction may
symbols
in the manual and the unit
Take
care
of
Take
care
of electric shock that may
After
reading
danger
that may
this manual,
meaning
keep
happen
it in the
under
happen
place
cause
are as
specific
under
that the
misuse of the
or
of it is
as
serious
cause
light injuries
projector.
below.
injuries
or
and
damage
even
of the
death.
projector.
below.
condition.
specific
user
condition.
always
can
contact
easily.
WARNING
Do not attempt to repair or adjust this
equipment. Contact your dealer or Service
center. High risk of electric shock!
Do not
place anything containing liquid
on
top of the projector. High risk of Electric
Shock
or
damage
This may cause
or could give an
a
to the
projector.
fire
BLANK
VOL+
SOURCE
electric shock.
OL
-
ENTER
ENU
BLANK
ENTERVOL+
SOURCE
VOL
MENU
PUSH
Don't insert any
object
into the exhaust vent
.
Don't
This may cause a fire
an electric shock.
or
could
give
the projector in direct sunlight
heat source(radiator or heater).
place
or near a
This may cause
or could give an
a
fire
electric shock.
BLANK
ENTERVOL+
OL
MENU
SOURCE
BLANK
SOURCE
ENTEROL+
VOL
MENU
PSH
PSH
3
ENGLISH
WARNING
Don't
any covers (except lens
risk of Electric Shock!
remove
cover). High
Use
with
air spray or soft cloth that is wet
neutral detergent and water for
removing dust or stains on the projection
lens.
an
a
BLANK
OURCE
OL+
ENTER
BLANK
R
OL+
VOL
MENU
SOURCE
OL
ME
P
PUSH
Only use the correct type of batteries for
the remote control. Dispose of used batteries carefully.
This may cause
or could give an
electric shock.
a
Don't look directly onto the lens when the
is in use. Eye damage may occur!
projector
fire
BLANK
SOURCE
VOL+ENTER
VOL-
MENU
NK
ENTER
VO
SOU
VO-
MENU
PUSH
Don't use the projector in damp place such
bathroom or any place where it is likely to get wet. Serious damage could occur
or risk of Electric Shock!
as a
SOURCE
Don't use the projector if there is smoke
unusual smell from the projector.
Disconnect from the mains and contact
the service center. Risk of fire!
or
BLANK
VOL+
TR
VOL-
ENU
BLANK
VOL+
SOURCE
VOL
-
EN
ER
MENU
PUSH
PUSH
Don't look at laser beam
cause
eye
directly
as
it may
damage.
4
Safety
Instructions
NOTES
No
impact
on
the lens while moved.
No contact while
working,
or
right
after the
lamp
lamp
is off since the exhaust port and the
lid generate heat.
Don't
cover
H
SOURCEBLANK
use the
ble surface.
Only
OLOL+
MEN
U
ENTER
projector
on a
level and sta-
the
It makes internal
It may fall down
or be upset.
and
causes a
project
when in
use.
temperature increase
fire.
NK
BL
SOURCE
VOL+ENTER
L
BLANK
ENTERVOL+
SOURCE
VOL
MENU
USH
PUSH
Never touch the power
It may
cause
plug
with wet hand.
electric shock.
Don't use alcohol, benzene, or thinners to
clean any plastic parts of the projector.
Never use industrial chemicals or deter-
gents.
SOU
Ensure the power lead doesn't trail
any hot objects like a heater.
It may make
covering
and
cause a
Disconnect from the mains and
connections before moving.
of cords may cause
electric shock.
Damage
parts melted
or
across
a
fire
or
fire
electric shock.
UH
L
L+
-
M
5
remove
all
ENGLISH
NOTES
Don't touch the lens of the
damage of it.
projector.
It may
cause
Don't use any sharp tools on the
this will damage the casing.
projector
as
BLANK
SOURCE
ENTERVOL
VO-
MENU
BLANK
ER
VOL+
EN
SOURCE
VOL
MENU
PU
If the
tact
can
projector requires cleaning inside conthe service centre. Accumulated dust
cause mechanical failure.
Place the projector where people will not
or tread on the power lead.
trip
LNK
E
V
OUR
VOL
BLANK
VOL+ENTER
SOURCE VL
PSH
Use the indicated type of power source on
the projector. If you are not sure of the type
of power available, consult your dealer or
customer service center.
Don't place the projector or the remote
control on a heater or use in a heated car.
BLANK
OL+
ENTER
SOURCE
OL
MENU
PUSH
Don't use the projector when the power
cord or the plug is damaged or the connecting part of wall socket is loose.
Be sure to unplug when you don't use
the projector for a long period or you are
absent.
It may cause electric shock
fire.
Accumulated dust may
or a
cause a
ANKB
E
ENTER VO
SOUR
VO-
fire,
electric shock from
MENU
deterioration,
USH
or
electric
leakage.
6
Names of parts
Main
Body
Rear remote
control sensor
Power button
Speaker
Control
panel
Indicators
POWER
Handle
SOURCE
BLANK
VOLVOL+
MENU
ENTER
Foot adjusting
button
Horizontal
leveler
Front remote
control sensor
Rear
Zoom
Foot
ring
Focus
Lens
ring
cover
Part
Connecting
Connecting
Computer
Out
Computer
Audio
Mouse
Mouse
Computer
Computer
Audio
Computer
Out
Computer
R Audio
L/MONO Video
In
In
S-Video
S-Video
AC
Audio / Video
K
Main power button
Kensington Security
System Connector
(Refer to page 12)
Rear remote control
7
sensor
ENGLISH
Control
Control Panel
ENTER Button
MENU Button
Selects
or
menus.
Δ,ΕButton
Selects
menus
items in the
Checks
closes
MENU
VOL-
saves
present mode and
the
change
VOLUME Button
Adjusts
menus.
volume level and
functions of
SOURCE Button
PC
of functions.
VOL+
and
SOURCE
Switches to
ENTER
menus.
BLANK
BLANK Button
or
AV mode.
POWER
POWER Button
8
Names of
parts
Remote Control
Control
POWER Button
MENU Button
SOURCE Button
L MOUSE Button
R
(Zoom-out Button)
(Zoom-in Button)
MOUSE Button
POINTER Button
MOUSE DRAG Button
LASER Button
ENTER Button
BLANK Button
STILL Button
RESIZE Button
MUTE Button
VOLUME Button
ZOOM Button
AUTO TRACKING Button
Inserting
1
9
the batteries
Slide the battery cover
in the direction of the
arrow
to remove.
2
Insert the batteries with
correct
polarity.
3
Replace
the
battery
compartment
the
arrow
cover
direction.
to
ENGLISH
Functions
on
on
the
the Remote Control
Control
Button
Function
POWER Button
Selects ON/OFF of power.
SOURCE Button
Switches to PC
MENU Button
Displays
L MOUSE Button
(Zoom-out Button)
R MOUSE Button
(Zoom-in Button)
POINTER Button
*
or
or
AV mode.
hides the
menu.
Corresponds to the Left
registers a menu selection
Click of PC Mouse. This button
and selects other custom functions.
on the zoom function.
-
*
*
Downsizes the
screen
Corresponds to the Right Click of PC Mouse. This button
registers a menu selection and selects other custom functions.
Enlarges the screen size on zoom function.
-
*
*
*
*
After selecting menus, controls selecting and adjusting
functions with the direction of up, down, left, right.
Moves the screen with the direction of up, down, left, right
on zoom function.
Moves and releases the selected icon on PC screen.
icon in PC mode.
MOUSE DRAG Button
Uses to select and
ENTER Button
Checks the present mode and
ZOOM Button
Refer to page 38.
RESIZE Button
Refer to page 36.
drag
an
saves
the
change
of functions.
AUTO TRACKING Button Refer to page 39~40.
BLANK Button
Refer to page 33~34.
STILL Button
Refer to page 28.
MUTE Button
Cuts off audio.
VOLUME Button
Adjusts
LASER Button
Makes
(Don't
volume level.
bright red laser point on the screen for attention.
look at laser beam directly as it causes eye damage.)
a
10
Installation and Connection
Accessories
1.5V
1.5V
Remote Control
Batteries 2
(size AA)
Power Cord
Portable
Bag
Audio/Video Cable
ON
123456789
Audio Cable
Computer
Cable
Mouse
SCART to RCA jack
Connecting
Optional
PC
or
MAC Serial Mouse Cable
Compatible)
Extras
*
Contact your dealer for
*
When
*
Contact your
buying these items.
ceiling installer, use only the ceiling
dealer for replacing a new lamp.
applying
a
installer for LCD
projector.
Ceiling
S-Video Cable
Lamp
Screen for
11
Desktop Adaptor
Cables
PS/2 Mouse Cable
(IBM
MAC
(option)
projecting
installer for LCD
projector
ENGLISH
Using
Security System
System
Using Kensington Security
The
projector has Kensington Security System
Security system cable as below.
Connector
on
the back
panel.
Connect the
Kensington
For the detailed installation and
use of the Kensington Security System, refer to the user's guide
Kensington Security System set.
And for further information, contact http://www.kensington.com, the internet homepage of the
Kensington company that deals with expensive electronic equipments such as notebook PCs or LCD
projectors.
attached to the
Kensington Security System
is
an
optional
item.
K
AC
12
Installation and Connection
Status
Projector Status
*
Lamp Indicator, operation
projector.
Indicators
indicator and
temperature indicator
at the
top of the projector show the
user
the
operating
of the
Lamp
Indicator
Temperature indicator
Operation
indicator
MENU
VOL-
Orange
Operation
Lamp
Indicator
Green
Standby.
On operation.
Off
Power off.
Red
to be
Indicator
Red(flashing)
Green(flashing)
ENTE
VOL+
Projection lamp is reaching the end of its life and needs
replaced with a new lamp.(over 1400 hours)
Arrange lamp-replacement through service center.
"Replace the Lamp"
The projector has trouble in the lamp or around it.
Contact the service center.
The
lamp cover is not closed.
projector is in high temperature. If you don't
turn off the projector, it'll be turned off automatically.
"Temperature is Too High"
The projector is turned off as its high temperature.
Power is turned off as the trouble of internal cooling
This
Orange
Temperature
Indicator
Red
Red
"
13
"
is the
warning
message
(flashing)
on screen.
fan. Contact your service center.
status
ENGLISH
Basic
of
of the
Operation
Operation
Projector
POWER
BLANK
SOURCE
VOLVOL+
MENU
ENTER
1.
Place the
projector
on a
surface with the PC
22.
Place the
the
and the
the
projector
screen.
or
sturdy
AV
and horizontal
source.
in the correct distance from
The distance between the
screen
projector
determines the actual size of
image.
Screen size
610x460cm(300inch)
410x300cm(200inch)
200x150cm(100inch)
160x120cm(70inch)
120x90cm(50inch)
81x61cm(40inch)
Horizontal distance from
projector
to
screen
12.55m~16.35m
8.35m~10.87m
4.16m~5.42m
2.90m~3.78m
2.06m~2.69m
1.64m~2.15m
3.
3
Turn the
44.
Connect the cables of the
projector so that the lens can be at a
right angle to the screen. If the projector is not
at a right angle, the screen image will be
crooked. At this time perform keystone function.
(Refer to page 37.)
projector
power socket and other connected
to
a
wall
sources.
14
Connecting
*
You
can
*
You
can use
*
connect the
projector to
to a
Desktop PC
computer of VGA, SVGA, XGA and SXGA output.
a
resize function for VGA, SVGA output.
Refer to page 42 for the projector supported monitor
display.
Mouse
Computer
Co
Out
C
Au
R
dio
L/M
deo
In
S
e
AC
K
d
c
a
b
<
How to connect
>
a.
Connect either end of the computer cable to
b.
Connect the monitor cable from the PC monitor to
projected image
c.
15
In of the
Computer
projector.
Out of the
projector
if you want to
see
the
PC monitor.
Connect the audio cable from the PC
*
d.
on
Computer
(LINE
OUT sound
port)
to
Computer Audio
of the
projector.
If the PC has two audio out ports of SPEAKER OUT and LINE OUT, connect the LINE OUT port to get
better sound quality.
Connect the PS/2
mouse(for
IBM PC
or
compatible) cable(6 pin)
to the Mouse of the
projector.
Connecting
to a Notebook PC
ENGLISH
Mouse
Computer
Computer Out
Au
R
C
dio
L/M
deo
n
S
eo
AC
K
a
b
c
<
How to connect
>
a.
Connect either end of the computer cable to
b.
Connect the audio cable from the PC to
c.
Connect the PS/2
mouse(for
IBM PC
or
Computer
In of the
Computer Audio
of the
compatible) cable(6 pin)
projector.
projector.
to the Mouse of the
projector.
16
to a Macintosh
Connecting
*
You must
the Macintosh
use
desktop adaptor
to connect the
projector
to
a
Desktop PC
Macintosh PC.
Mouse
Computer
Com
r
Out
Co
Aud
R
dio
L/M
In
deo
K
ON
123456789
c
b
a
d
f
e
<
How to connect
a.
b.
Connect either end of the computer cable to
Computer
the
Set the
projected image
adjusting
you want to
use
on
number and letter of the Macintosh
and connect the
adaptor
Computer
Out of the
projector
e.
Connect the audio cable from the PC to
f.
Connect the
cable(4 pin)
desktop adaptor in accordance
(Refer to page 18 19)
to the Macintosh.
Connect the computer cable to the Macintosh
mouse
projector.
if you want to
Macintosh monitor.
d.
17
In of the
Connect the monitor cable from the Macintosh monitor to
see
c.
>
with the resolution
~
desktop adaptor.
Computer Audio
from the Macintosh
of the
mouse
port
projector.
to the Mouse of the
projector.
ENGLISH
How to
use
use
the
the Macintosh
Adjusting
desktop
desktop adaptor
letter
ON
123456789
Adjusting
a.
How to
use
Usually set 1
the adjusting
b.
number
Notes for
~
6 to OFF status and 7
~
9 to ON status of the
adjusting numbers. And select
(Refer to page 19.)
letter which is correct to the Macintosh and the monitor.
Connecting
to the Macintosh PowerBook
If you get problems when connecting it to the
status and restart the Macintosh PowerBook.
projector,
set the
adjusting
number 9 to OFF
18
Connecting
to a Macintosh
Desktop PC
of MAC desktop adaptor in accordance
accordance with
with kinds of
of MAC and
and output
Adjusting letters of
output spec.
spec.
output
resolution
12￥RGB
13￥x14￥RGB
15￥Portrait
VGA
SVGA
SVGA
16￥Color
19￥Color
19￥Color
2Page Mono
21￥Color
NTSC
PAL
512x384
640x480
640x870
640x480
800x600
800x600
832x624
1024x768
1024x768
1150x870
1152x870
NTSC
PAL
frequency(KHz)
frequency(Hz)
24.5
35
68.8
31
35
50
60
68.7
68.7
15.7
16
60
66
75
60
56
56or72
75
75
60or70
75
75
60
50
letter
N
J
O
G
G
G
F
D
G
M
P
L
H
llci, llsi
N
J
O
llvi, llvx
N
J
G
LC
N
J
M
LCII
N
J
G
LCIII
N
J
O
G
LC 475, LC 550
N
J
O
G
G
F
LC 575
N
J
O
G
G
F
M
P
L
H
400,405,410,430,600,600CD
N
J
450
N
J
O
G
700,900
N
J
O
G
G
F
M
P
L
H
605,610,650,800,950
N
J
O
G
G
F
D
M
P
L
H
840AV
N
J
O
G
G
F
D
M
P
L
H
610,650
N
J
O
G
G
F
D
M
P
L
H
660AV
N
J
O
G
G
F
D
M
P
L
H
N
J
O
G
G
F
N
J
O
G
G
F
N
J
O
M
P
L
H
output spec
horizontal
vertical
MACS
adjusting
MAC
MAC
F
D
Performa
G
F
Quadra
G
G
Centris
G
G
PowerBook
160,165C,180,180C
DUO
DOC, MINI DOC
8 24 BOARD
19
F
Connecting
to a Macintosh PowerBook
ENGLISH
Mouse
Computer
Computer Out
Aud
R
Co
o
dio
L/MO
In
deo
K
b
ON
123456789
c
a
d
e
<
How to connect
>
a.
Connect either end of the computer cable to
b.
Set the
adjusting
Computer
number and letter of the Macintosh
you want to use and connect the
adaptor
In of the
desktop adaptor in accordance with
PowerBook.(Refer to page 18
to the Macintosh
c.
Connect the other end of the computer cable to the Macintosh
d.
Connect the audio cable from the PC to
e.
Connect the
mouse
projector.
Computer Audio
cable from the Macintosh
mouse
port
the resolution
~
19)
desktop adaptor.
of the
projector.
to the Mouse of the
projector.
20
to a Video Source
Connecting
*
*
In AV input mode, if the auto video
AUTO TRACKING button on the
You
can
connect
a
VTR,
system recognition fails
camcorder,
a
a
to detect a correct video system type, please press the
projector executes the fine auto video system recognition.
other compatible video image source to the projector.
Then the
remocon.
LDP
or
any
Mouse
Computer
Computer Out
Audio
R
Audio
Computer
L/MONO Video
In
S-Video
S VIDEO
(R) AUDIO (L)
VIDEO
OUT
K
IN
a
b
<Howtoconnect1>
a.
When
connecting
the
projector
to an A/V source, connect the A/V
put ports of the A/V source with A/V cables of the
is white and right audio is red.
same
input ports
of the
color. The video cable is
projector to the outyellow and the left audio
<Howtoconnect2>
b.
Connect S-Video
*
*
*
21
You
input port
of the
projector
to S-Video
output port of A/V
source
with S-Video cable.
get better picture quality when connecting S-Video source to the projector.
If you connect S-Video cable and Video cable simultaneously, you will get only the playing
Video source.
can
If the Audio output of other external
port(Audio L) of the projector.
equipments
is mono, do connect Audio cable
only
image
of S-
to the white
Connecting
*
*
to a D-TV
Settop
Box
To receive the DTV program, it is necessary to purchase DTV receiver (Settop Box) and
connect it to the projector.
Please refer to the owner's manual of the DTV Settop Box for the connection between LCD
projector and DTV Settop Box.
Mouse
<D-TV
Computer
Computer
Out
Audio
R Audio
Co
L/MONO Video
Settop
Box
rear>
n
S-V
o
K
)
AUDIO (
DTV OUT
b
a
<
How to connect
>
Computer In of the projector to DTV OUT of the
input ports (R, L/Mono) of the projector to
a.
Connect the
b.
Connect the Audio
Settop
D-TV
Settop
Box.
the Audio output ports
(R, L)
of the D-TV
Box.
22
ENGLISH
the
Operating
Focusing
When
an
and
image appears
Projector
Positioning
on
the Screen
Screen
Image
the screen, check if it is in proper focus and fits well to the
screen.
POWER
SOURCE
BLANK
VOLVOL+
MENU
ENTER
Zoom
To
To
adjust the
adjust the
To raise
ring
Focus
ring
focus of the
size of the
or
by pushing
image, rotate the focus ring which is the outer ring on the lens.
image, rotate the zoom ring which is the inner ring on the lens.
lower the
foot
image on the screen,
adjuster button as below.
extend
or
retract the foot at the bottom of the
projector
Push
1.
Press the foot
adjuster button while you support the other side of the projector.
freely. Take care not to drop the projector.
While pressing the foot adjuster button, raise or lower the projector to place the
Release the button to lock the foot in its new position.
To fine-tune the height of the projector, rotate the front foot to raise or lower it.
After raising the front foot, do not press down on the projector.
This unlocks the foot and
can
make it
move
2.
3.
4.
23
screen
image
in the proper
position.
ENGLISH
If the
projector
is installed
on a
place
that is not stable
or
horizontal, the projected
screen
shape
will be distorted.
POWER
SOURCE
BLANK
VOL-
MENU
VOL+
ENTER
Horizontal leveler
Adjust
the
screen
shape to
be horizontal and
rectangular
with horizontal leveler
as
above.
24
Turning
the
on
1
Remove the lens
2
Press the main power button
on
Press the POWER button
up of the
the remote control
3
cover
during warming
of the
Projector
on
projector.
the back
panel.
or
top cover.(Green operation indicator flashes
lamp.)
It will take about 1 minute to
display
the
picture
after power
on
because the
lamp
of the
projector
needs
preheating.
image appears
An
Select the
4
source
after the green power indicator is flashed for
mode with the SOURCE button.
some
time.
volume level.
Adjust
If you press VOLUME Γ button, sound and volume level number
If you press VOLUME Φ button, sound and volume level number
are
are
increased.
decreased.
24
*
POWER
SOURCE
BANK
VO
L
-
VOL+
ENTER
25
MENU
Don't turn main power off and don't
is working.
pan(inlet/outlet)
unplug
the power cord while the ventilation
Function
*
1
2
Without PC
or
Video
checking
signal
ENGLISH
the OSD doesn't appear.
Press the MENU button.
Move the POINTER button up or down to select
press the button you can see menus as below.
u
exit
and press the ENTER button. Each time you
a menu
enter
move
exit
u
Γ VIDEO
move
adjust
VIDEO
Ε
Γ POSITION
Contrast
Γ SPECIAL
Color R
Color G
Color B
Reset
80
Brightness
Γ TRACKING
Γ POSITION
Γ SPECIAL
Γ TRACKING
u
exit
move
enter
u
exit
select
move
u
exit
move
Γ VIDEO
Γ VIDEO
Γ VIDEO
Γ POSITION
Γ POSITION
Ε
Γ SPECIAL
Ε
Ε
TRACKING
SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
Press Enter to Start
Auto Tracking
Clock
Phase
English
Horizontal
Vertical
Γ
adjust
POSITION
0
Keystone
Zoom
Resize
Γ SPECIAL
VGA Text
Γ TRACKING
Γ TRACKING
3
Move the POINTER button up
To finish the
*
In AV mode,
menu are
*
menu
The sub
not
display,
[Horizontal]
or
down to select
press the MENU button
/
[Vertical]
a
function that you want to
use or
adjust.
repeatedly.
in POSITION menu,
[VGA Text]
in SPECIAL
menu
and TRACKING
displayed.
menus
of VIDEO
menu
in AV mode
are
different from those in the PC mode.
(Refer to
page
41).
26
1
Press the SOURCE button
2
Each press of the SOURCE button
PC
27
changes
the
AV
display
as
below.
Using Still
1
function
Press the STILL button.
*
You
can
still the
input image
from PC
or
AV
source.
<Still
<Moving Image>
2
ENGLISH
To finish this function, press the STILL button
Image>
again.
28
Selecting language
1
Press the MENU button and
below.
the POINTER button up
move
or
down to select the SPECIAL
or
down to select
menu
as
u
exit
enter
move
Γ VIDEO
Γ POSITION
Γ SPECIAL
Γ TRACKING
2
3
Press the ENTER button and
Move the POINTER button left
move
the POINTER button up
right
or
to select the
you want to
On-Screen-Display(OSD) is marked in the selected language from
menu display, press the MENU button repeatedly.
To finish
u
exit
move
select
Γ VIDEO
Γ POSITION
Ε
SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
Γ TRACKING
29
language
English
Γ
this
point.
use.
[Language]
item.
Checking lamp
1
Press the MENU button and
below.
time
ENGLISH
the POINTER button up
move
or
down to select the SPECIAL
menu
as
u
exit
enter
move
Γ VIDEO
Γ POSITION
Γ SPECIAL
Γ TRACKING
2
Press the ENTER button and
item.
move
u
the POINTER button up
exit
or
down to select the
[Lamp Time]
move
Γ VIDEO
Γ POSITION
Ε
SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
0Hr
Γ TRACKING
You
can see
When the
the used
lamp
time is
lamp time.
reaching 1400 hours,
the
lamp
indicator is turned to red color.
30
Horizontal / Vertical function
Using Flip
Flip
*
Horizontal Function
This function
onto
1
a
reverses
transparent
the left and the
screen
being
right side
of the
viewed from the
Press the MENU button and
move
Use this function when
projected image.
opposite side.
the POINTER button up
u
exit
move
or
projecting from
down to select the SPECIAL
behind
menu.
enter
Γ VIDEO
Γ POSITION
Γ SPECIAL
Γ TRACKING
2
Press the ENTER button and
move
the POINTER button up
u
exit
move
or
down to select
[Flip Horizontal]
enter
Γ VIDEO
Γ POSITION
Ε
SPECIAL
Language
Flip Horizontal
Press Enter to
Flip Vertical
Blank Image
Lamp Time
Flip
VGA Text
Γ TRACKING
3
Press the ENTER button to
see
reversed
image.
Each time you press the button, the image will be reversed.
menu display, press the MENU button repeatedly.
To finish
u
exit
move
enter
enter
move
Γ VIDEO
Γ POSITION
Ε
Flip Vertical
Blank Image
Lamp Time
VGA Text
Γ TRACKING
31
n
POSITION Γ
SPECIAL
Language
Flip Horizontal
exit
VIDEO Γ
Press Enter to
Flip
SPECIAL
Language
Flip
to Enter Press
Ε
Horizontal Flip
Vertical Flip
Image Blank
Time Lamp
Text VGA
TRACKING Γ
item.
Vertical
Flip Vertical
*
*
ENGLISH
Function
This function reverses the upper and the lower side of the projected image.
When you hang the projector upside down from the ceiling for using, you need to
lower) of the image.
1
Press the MENU button and
move
the POINTER button up
exit
u
move
reverse
all the
sides(left, right,
down to select the SPECIAL
or
upper,
menu.
enter
Γ VIDEO
Γ POSITION
Γ SPECIAL
Γ TRACKING
2
Press the ENTER button and
move
the POINTER button up
u
exit
move
or
down to select
[Flip Vertical]
item.
enter
Γ VIDEO
Γ POSITION
Ε
SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
Press Enter to
Flip
Γ TRACKING
3
Press the ENTER button to
see
reversed
image.
Each time you press the button, the image will be reversed.
menu display, press the MENU button repeatedly.
To finish
u
exit
move
enter
Γ TRACKING
Γ VIDEO
VGA Text
Lamp Time
Γ POSITION
Ε
Image
Flip Vertical
Flip Horizontal
Blank
SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
Press Enter to
Flip
Language
Press Enter to
Flip
Ε
SPECIAL
Γ POSITION
Γ VIDEO
Γ TRACKING
u
M
exit
move
enter
32
Using
*
1
2
This function may be effective if you need to
get attention of the attendants in meetings
Press the BLANK button.
*
The
*
You
screen
can
turns to be covered with
choose the
background
background
color and sound becomes off.
color. Refer to page 34.
To exit the blank status, press the BLANK button
*
33
Blank function
If
exiting
the blank status sound also becomes
on.
again.
or
briefings.
ENGLISH
Selecting
Selecting
1
Blank
color
color
Image
Press the MENU button and
the POINTER button up
move
exit
u
move
or
down to select the SPECIAL
menu.
enter
Γ VIDEO
Γ POSITION
Γ SPECIAL
Γ TRACKING
2
Press the ENTER button and
item.
3
Move the POINTER button left
Background
To exit
menu
color will be
display,
move
or
the POINTER button up
right
or
press the MENU button
u
[Blank Image]
to select the color you want to use.
to the selected color from this
changed
down to select the
exit
move
point.
repeatedly.
select
Γ VIDEO
Γ POSITION
Ε
SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
Blue
Γ
Γ TRACKING
34
Selecting
*
PC
screen
size
input signal
When PC
input mode, select the appropriate screen size in SPECIAL menu as below before turning on the
get the image size of PC on DOS mode to be fit on the projected screen.
In other screen size signals except 640X400 70Hz and 720X400 70Hz, the projected screen sizes are adjustPC to
*
ed
1
automatically.
Press the MENU button and
below.
the POINTER button up
move
or
down to select the SPECIAL
menu
as
u
exit
move
enter
Γ VIDEO
Γ POSITION
Γ SPECIAL
Γ TRACKING
2
Press the ENTER button and
item.
3
Move the POINTER button left
move
or
the POINTER button up
right
u
or
down to select the
[VGA Text]
to select the screen size you want to use.
exit
move
select
Γ VIDEO
Γ POSITION
Ε
SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
720X400
Γ
Γ TRACKING
a.
Selecting 720X400
: When input signals
are
720X400 70Hz
or
640X400 70Hz
,
the
projected
screen
size is
always adjusted
or
640X400 70Hz
,
the
projected
screen
size is
always adjusted
to the format of 720X400 70Hz.
b.
Selecting 640 X 400
: When input signals
are
720X400 70Hz
to the format of 640X400 70Hz.
To exit
35
menu
display,
press the MENU button
repeatedly.
Resize function
Using
*
1
You
can use
this function
only
under SVGA
(800x600)
mode in
case
ENGLISH
of LP-XG2 model.
Press the RESIZE button.
Each press of the button
changes
the
display
as
<PCmode>
SOURCE
BLANK
VOL-
VOL+
ENTER
<
AV/DTV mode
Scaled
4:3
Original
16:9
*
POWER
below.
You
can
also
use
this function
by using
>
the MENU button.
MENU
36
Adjusting
screen
display
Positioning
*
*
If the image size does not fit the screen in accordance with the input source, set the position of the
image by selecting Horizontal / Vertical position.
Keystone function adjusts the upper and lower width of the projected image to prevent the image
shape from being a trapezoid shape. Use this function when the screen or the projector is slanted
and cannot make rectangular projection angle.
1
Press the MENU button and
move
the POINTER button up
u
exit
or
down to select the POSITION
menu.
enter
move
Γ VIDEO
Γ POSITION
Γ SPECIAL
Γ TRACKING
2
Press the ENTER button and
or (Keystone) item.
the POINTER button up
move
or
down to select
(Horizontal),
(Vertical)
PCmode
<
u
exit
move
>
adjust
Γ VIDEO
Ε
POSITION
Horizontal
Vertical
0
Keystone
Zoom
Resize
Γ SPECIAL
Γ TRACKING
3
Press the POINTER button and move the button left
adjust the screen condition as you want.
(Horizontal), (Vertical) (Keystone)
,
To exit the
37
or
right
or
press the VOLUME
to
menu
display,
are
adjusted
press the MENU button
from -50 to +50.
repeatedly.
(Φ,Γ)
button
ENGLISH
Zoom Function
1
2
3
Press the ZOOM button.
Move the POINTER button to
to zoom the
target
move
the
rectangular zooming
Press the L MOUSE
R MOUSE button to
or
*
L MOUSE button makes the
*
R MOUSE button makes the
image
image
Move to the
position
left,right,up,
or
5
Press the ZOOM button
*
L+VO
ENTER
MENU
you want to
see
the
down.
POWER
VOL-
adjust
the
zoom
level.
larger.
25/25
4
SOURCE
and press the ENTER button
look smaller.
look
11/25
BLANK
area
area.
*
You
again
can use
In the
zoom
enlarged display by moving
the POINTER button
to finish the zoom function.
this function
mode, you
by using
adjust
can
the MENU button.
horizontal / vertical
position
with the POINTER
button.
38
Using Tracking
Auto Tracking
Tracking
*
Auto
Tracking
This function
1
signals
Function
Function
assures
and tremor of the
ic
function
you of getting the best video quality by automatically adjusting the difference of horizontal width
This difference is caused by disaccord of the internal signal of the projector and diverse graph-
image.
of PC.
Press the AUTO TRACKING button.
Auto
*
2
Image positioning
and tremor
are
automatically performed.
Adjust [Clock] or [Phase] in TRACKING menu after operation of [Auto Tracking] if you want
get better picture quality in accordance with diverse PC input modes. (Refer to page 40.)
*
POWER
*
SOURCE
BLANK
VOLVOL+
ENTER
MENU
You
can
also
use
by using the MENU button.(PC mode)
stopped image because you may not get
moving image of PC graphic signal.
quality
on a
to
this function
Perform this function while
video
39
adjusting
Tracking
on
the best
ENGLISH
Clock
Clock / Phase Function
*
Clock Function
This function
*
adjusts
the horizontal width of the
projected image
to
get the image
to fit
on
the
screen
size.
Phase Function
This function is for the detailed
1
adjustment
Press the MENU button and
of the clock function.
move
the POINTER button up
or
down
to select the TRACKING
menu.
u
exit
move
enter
Γ VIDEO
Γ POSITION
Γ SPECIAL
Γ TRACKING
2
Press the ENTER button and
item.
move
the POINTER button up
or
down to select the
(Clock)
or
(Phase)
u
exit
move
adjust
Γ VIDEO
Γ POSITION
Γ SPECIAL
Ε
TRACKING
Auto Tracking
Clock
Phase
3
Move the POINTER button left
condition.
To exit the
menu
display,
or
right
or
0
press the VOLUME
press the MENU button
(Φ,Γ)
button to
adjust
the
screen
repeatedly.
40
Adjusting
1
Video
Press the MENU button and
move
the POINTER button up
or
<PC Mode>
exit
u
move
down to select each VIDEO
menu.
<AV Mode>
enter
u
exit
Γ VIDEO
Γ VIDEO
Γ POSITION
Γ POSITION
Γ SPECIAL
Γ SPECIAL
enter
move
Γ TRACKING
2
Press the ENTER button.
<PC Mode>
u
Ε
exit
move
<AV Mode>
adjust
u
VIDEO
Contrast
Ε
exit
move
Brightness
adjust
VIDEO
Contrast
80
80
Brightness
Color R
Color G
Color B
Reset
Color
Tint
Reset
Γ POSITION
Γ POSITION
Γ SPECIAL
Γ SPECIAL
Γ TRACKING
3
Move the POINTER button up
or
down to select
4
Move the POINTER button left
video item as you want.
or
right
To restore the
To finish
41
or
a
video item you want to
press the VOLUME
(Φ,Γ)
original image condition after changing it, press ENTER
display, press the MENU button repeatedly.
menu
adjust.
button to
button after
adjust the
selected
selecting (Reset)
item.
*
The
projector displays images at a
images(1152x864mode, 1280x1024mode),
display formats supported by the projector.
resolution
the
of
projector
1024x768
pixels.
To
display higher resolution
following table lists the
compresses it to 1024x768. The
Vertical
Horizontal
Freq. (kHz)
Sources
Format
VGAEGA
640X350
70.090Hz
31.468kHz
640X350
85.080Hz
37.861kHz
640X400
85.080Hz
37.861kHz
720X400
70.082Hz
31.469kHz
720X400
85.039Hz
37.927kHz
640X480
59.940Hz
31.469kHz
640X480
66.667Hz
35.00kHz
640X480
72.800Hz
37.861kHz
640X480
75.00Hz
37.500kHz
640X480
85.008Hz
43.269kHz
640X480
100.040Hz
53.011kHz
640X480
120.00Hz
64.062kHz
800X600
56.250Hz
35.156kHz
800X600
60.317Hz
37.879kHz
800X600
72.188Hz
48.077kHz
800X600
75.00Hz
46.875kHz
800X600
85.061Hz
53.674kHz
800X600
90.00Hz
56.00kHz
800X600
100.00Hz
64.016kHz
1024X768
43.479Hz
35.522kHz
1024X768
60.004Hz
48.363kHz
1024X768
70.069Hz
56.476kHz
1024X768
75.029Hz
60.023kHz
1024X768
84.997Hz
68.677kHz
1152X864
60.053Hz
54.348kHz
1152X864
70.016Hz
63.995kHz
1152X864
75.00Hz
67.500kHz
1152X864
85.057Hz
77.487kHz
1280X960
60.00Hz
60.00kHz
1280X960
75.00Hz
75.00kHz
1280X960
85.002Hz
85.938kHz
1280X1024
60.020Hz
63.981kHz
1280X1024
75.025Hz
79.976kHz
1280X1024
85.024Hz
91.146kHz
1600X1200
60.00Hz
75.00kHz
832X624
74.550Hz
49.725kHz
1024X768
60.004Hz
48.363kHz
1024X768
75.029Hz
60.023kHz
1152X870
75.062Hz
68.681kHz
1920X1080i
60.00Hz
33.750kHz
1280X720p
60.00Hz
45.00kHz
PC98 / VGA text
VGA
SVGA
XGA
SXGA
UXGA
MAC 16￥
19￥
20￥
HD
*
If the
*
The
Freq.(Hz)
projector does not support the input signal, "CHECK INPUT SIGNAL" message appears on
projector supports DDC1/2B type as Plug & Play function.(Auto recognition of PC monitor)
the
screen.
42
Maintenance
*
The
needs little maintenance. You should
projector
the
keep the lens clean because any dirt
You will also need to clean the air filter attached at the bottom of the
or
stains may appear
projector periodically
because a clogged air filter prevents proper ventilation that is necessary to cool the projector and prevents it
from overheating. If any parts need to be replaced, contact your dealer. When cleaning any part of the
projector, always turn the power off and unplug the projector first.
on
screen.
the
the lens
Cleaning
Cleaning
Clean the lens whenever you notice dirt
or a soft, dry lint-free cloth.
or
dust
on
the surface of it.
Wipe
the lens surface
gently with
an
air
spray
To
remove
surface
dirt
or
stains
the
the
Cleaning
Cleaning
To clean the
Projector
and then
Do not
the lens, moisten
a
soft cloth with water and
a
neutral
detergent
and
wipe
the lens
wipe
use
Case
Case
projector case,
lint-free cloth. To
dry,
on
gently.
the
first
remove
unplug
the power cable. To remove dirt or dust, wipe the
or stains, moisten a soft cloth with water and
stubborn dirt
casing with a soft,
a neutral detergent
casing.
alcohol, benzene, thinners
or
other chemical
detergents
as
these
can cause
the
casing
to be
warped.
Cleaning
Cleaning
the
the Air Filter
The air filter, which is located at the bottom of the projector, should be cleaned after every 100 hours' use.
If it is not cleaned periodically, it can become clogged with dust and prevent the projector from being ventilated
properly.
This may
To clean the air filter
cause
and
damage
of the
projector.
:
Switch the
projector off and unplug the power cable from the wall socket.
Stand the side of the projector so that the handle can be at the top, and you
Push the opening tip of the air filter cover and remove the cover.
1.
2.
3.
4. The air filter is in the
computers
or
If it is difficult to
6.
Plug
POWER
SOURCE
BLANK
VOL+
VOL- MENU
ENTER
cover
other office
5. Close the filter
43
overheating
remove
cover
easily
access
of it. To clean the filter, you'd better use a small vacuum cleaner
If not, you may use a dry, lint-free cloth.
the air filter.
designed
equipments.
dirt
after
can
or
the filter is torn, contact your dealer
or
the service center to
replace
it
.
cleaning.
the power cable back into the wall socket.
*
When
*
Contact your dealer to
explanation to install.
installing
the
projector on
get
the
screwes
ceiling use screws of which length is within 5
fixing, the ceiling installer and the detailed
for
mm.
for
Specifications.
LP-XG2
22.9mm(0.9 inches)
LP-XG2
:
1024(Horizontal)
x
768(Vertical)pixel
1.01~7.6m(40~300
inches)
1.64~16.35m(5.03~54.08
feet)
12m
1W
4:3(horizontal:vertical)
LCD
panel
resolution
projecting
remote control distance
speaker system
horizontal / vertical ratio
NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N
Video
compatibility
Operating
-
240V~50/60Hz
front
foot)
operation
:
Power
height
breadth
329.5mm(including lens)
length
3.4kg
weight
Condition
temperature
Projection Lamp
lamp
32~104°F(0°C~35°C)
: -4~140°F(-20°C~60°C)
humidity
80% relative
~
10
humidity by dry hygrometer
humidity by dry hygrometer
model
TP-L2
In storage and transit
operation : 20
operation :
distance
ratio
238mm
In
size
screen
zoom
98.5mm(including
Not in
size
1:1.3
AC 110
In
Model
power
consumption
150W
90% relative
~
44
">