LG | FLATRON-795FT-PLUS-FB795CP | LG FLATRON 795FT PLUS(FB795CP) Owner’s Manual

Table of Contents
Introduction
Introduction
Important
Installation
Operation
Technical Information
Precautions
A4
Making use of USB (Universal Serial Bus)*
A6
Location and Function of Controls
A8
Control Panel Function
A9
On Screen
Display (OSD) Control Adjustment
A10
On Screen
Display(OSD)
Appendix
795FT
Selection and
Adjustment
Energy Saving Design
Video
Applies to
A2
Connecting the Monitor
Low Radiation
*
A1
plus only.
i
A11
A15
Compliance (MPR II) and
DDC (Display Data Channel)
Memory Modes
A16
A17
Troubleshooting
A18
Service
A19
Specifications
A20
Communications Regulation Information
See back of manual
Environmental
See back of manual
Labelling of
Personal
Computers
ENGLISH
Introduction
Thank you for purchasing a high resolution monitor. It will give you
high resolution performance and convenient reliable operation in a
variety of video operating modes.
Features
The monitor is
17 inches
(16.0 inches viewable ) intelligent,
microprocessor based monitor compatible with most analog RGB (Red,
Green, Blue) display standards, including IBM PC , PS/2 , Apple ,
Macintosh , Centris , Quadra , and Macintosh II family.
USB
a
(Universal Serial Bus) ports
for the USB cable and hub. You
at the back of the monitor are
can
designed devices-such as a mouse,
for true Plug and Play function.*
prepared
easily and flexibly connect USBkeyboard or printer- to the monitor
The monitor
provides crisp text and vivid color graphics with VGA,
SVGA, XGA, and VESA Ergonomic modes (non-interlaced), and most
Macintosh
adaptor.
compatible
color video cards when used with the
The monitor's wide
video cards
compatibility makes it possible
or software without purchasing a new monitor.
appropriate
upgrade
to
Digitally controlled auto-scanning is done with the micro-processor for
scan frequencies between 30 and 96kHz, and vertical scan
frequencies between 50-160Hz. The microprocessor-based intelligence
allows the monitor to operate in each frequency mode with the
precision of a fixed frequency monitor.
horizontal
*
Applies to
Monitor
795FT
plus only.
We
Registration
accomplished
to
adapt
the advanced
monitor. Soft touch buttons
The model and serial numbers
the
rear
are
unique to this unit
requested
guide as a
your purchase. Staple
information here and retain this
permanent
receipt
on
are
to
conveniently adjust
screen
and
screen
a
the front
variety of image
design and technology to the
panel are simple and allow you
controls. The absolute flat
surface treatment eliminate
distracting glares.
and not available to
others. You should record
your
found
of this unit. These numbers
on
record of
here.
Date of Purchase
:
Dealer Purchased From
:
Dealer Address
:
Dealer Phone No.
:
Model No.
:
Serial No.
:
This monitor is
capable
1600 dots and
a
of
producing
a
maximum horizontal resolution of
maximum vertical resolution of 1200 lines. It is well
suited for CAD work and
For low cost of monitor
sophisticated windowing
environments.
operation, this monitor is certified as meeting
Energy Star requirements, and utilizes the VESA Display Power
Management Signalling (DPMS) protocol for power saving during nonuse periods.
the EPA
Important
Precautions
This unit has been
engineered and manufactured to assure your
personal safety, but improper use can result in potential electrical
shock or fire hazard. In order not to defeat the safeguards
incorporated in this monitor, observe the following basic rules for its
installation, use, and servicing. Also follow all warnings and
instructions marked directly on your monitor.
On
Safety
Use only the power cord supplied with the unit. In case you use another
power cord, make sure that it is certified by the applicable national
standards if not being provided by the supplier. If the power cable is
faulty in any way, please contact the manufacturer or the nearest
authorized repair service provider for a replacement.
Operate the monitor only from a power source indicated in the
specifications of this manual or listed on the monitor. If you are not sure
what type of power supply you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords
are
dangerous. So
power cords and broken plugs. They may result in
Call your service technician for replacement.
Do not
Open
a
shock
or
are
frayed
fire hazard.
the Monitor
There
are no user
There
are
serviceable components inside.
Dangerous High Voltages inside, even when the power is
OFF.
Contact your dealer if the monitor is not
operating properly.
To Avoid Personal
Injury :
place the monitor on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not try to roll a stand with small casters across thresholds or deep
pile carpets.
Do not
To Prevent Fire
or
Hazards:
Always turn the monitor OFF if you leave the room for more than a
short period of time. Never leave the monitor ON when leaving the
house.
Keep
children from
cabinet
openings.
dropping or pushing objects into the monitor's
Some internal parts carry hazardous voltages.
Important
Precautions
Do not add accessories that have not been
During
for this monitor.
Do not
lightning
period of time, unplug it from the wall outlet.
bring magnetic devices such as magnets or motors near the
picture
tube.
for
On Installation
designed
storm or when the monitor is to be left unattended
an
a
extended
Do not allow
place
anything to rest upon or roll over the power cord, and do not
the monitor where the power cord is subject to damage.
Do not
use
this monitor
near
water such as near a
bathtub, washbowl,
kitchen sink,
laundry tub, in
Monitors
provided with ventilation openings in the cabinet to allow the
generated during operation. If these openings are blocked,
are
a wet
basement,
or near a
swimming pool.
release of heat
built-up
heat
can cause
failures which may result in
a
fire hazard.
Therefore, NEVER:
Block the bottom ventilation slots
by placing
the monitor
on a
bed,
sofa, rug, etc.
Place the monitor in
a
built-in enclosure unless proper ventilation is
provided.
Cover the
openings with
Place the monitor
On
On
cloth
or
near or over a
other material.
radiator
or
heat
source.
Cleaning
Unplug the monitor before cleaning the face of the picture tube.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on
the picture tube because overspray may cause electrical shock.
Repacking
Do not throw away the carton and packing materials. They make an
ideal container in which to transport the unit. When shipping the unit
to another
location, repack it in its original material.
Installation
Connecting the Monitor
Connection to any IBM
VGA PC compatible
Figure 1 shows the signal cable connections from the monitor to the
Video Graphics Array (VGA) port typical in an IBM PC or PC
compatible. This also applies to any graphics video card for PC-CAD
or workstation that has a 15 pin high density (3 row) d-Sub connector.
system
1.
Power off both the monitor and PC.
2.
Connect the 15
pin VGA
connector of the
supplied signal
cable to the
connector on the rear of the monitor. The connectors
matching input
only one way. If you cannot attach the cable easily, turn
connector upside down and try again. When mated, tighten
will mate
thumbscrews to
secure
the connection.
3.
Power ON the PC, then the monitor.
4.
If you
see
the
the
the SELF DIAGNOSTICS message, check the
signal
cable
and connectors.
5.
*
Applies to
795FT
After
using
the system, power OFF the monitor, then the PC.
plus only.
*
D-15P
Signal
Power Cord
Figure
A4
1.
Cable
Installation
Connecting the Monitor
Connecting
to
an
Figure 2 shows the connection to an Apple Macintosh, using a
separately purchased adapter.
Apple
Macintosh PC
1.
Power OFF both the monitor and the PC.
2.
Locate the
computer
appropriate MAC
to VGA
adapter
block at your local
store. This
adapter changes the high density 3 row 15 pin
pin 2 row connection to mate with
the other end of the signal cable to the side of the
VGA connector to the correct 15
your MAC. Attach
adapter block with 3
3.
rows.
Connect the attached
adapter block/signal
cable to the video output
on
your MAC.
4.
Power ON the PC, then the monitor.
5.
If you
see
the SELF DIAGNOSTICS message, check the
signal
cable
and connectors.
6.
*
Applies to
795FT
After
using
the system, power OFF the monitor, then the PC.
Adapter
*
plus only.
15P
MAC6
D-15P
Power Cord
Signal
Figure 2.
A5
Cable
Installation
Making use of USB (Universal Serial Bus)
*
Bus) is an innovation in connecting your different
desktop peripherals conveniently to your computer. By using the USB,
you will be able to connect your mouse, keyboard, printer, and other
peripherals to your monitor instead of having to connect them to your
computer. This will give you greater flexibility in setting up your system.
USB (Universal Serial
USB allows you to connect chain up to 120 devices on a single USB port,
and you can "hot" plug (attach them while the computer is running) or
unplug them while maintaining Plug and Plug auto detection and
configuration. This monitor has an integrated self-powered USB hub,
allowing up to 4 other USB devices to be attached it.
1.
USB connection
Connect the upstream port of the monitor to the downstream port of
the USB
compliant PC or
port).
another hub
the USB cable
using
(Computer
must have a USB
2.
Connect the USB
compliant peripherals
the monitor.
to the downstream
ports of
USB downstream Ports
connect the cables from USB
compliant peripherals-such
keyboard, mouse, printer,
as
scanner, etc
USB upstream Port
etc.
mouse
keyboard
*
printer
to 795FT
Applies
plus
only(A6~A7page).
To USB downstream
the USB
compliant
port of
PC
or
another hub cable
USB
A6
Upstream connector
USB Downstream connector
Installation
*
Making use of USB (Universal Serial Bus)
Example of connection
monitor
scanner
computer
keyboard
mouse
printer
NOTE
To activate the USB hub function, the monitor must be connected to
compliant PC(OS) or another hub with the USB cable(enclosed).
a
USB
When connecting the USB cable, check that the shape of the connector at the
cable side matches the shape at the connecting side.
When the monitor is not plugged into an electric socket, the
connected to the downstream ports will not operate.
peripherals
Even if the monitor is in a power saving mode, USB compliant devices will
function when they are connected the USB ports(both the upstream and
downstream) of the monitor.
USB
specifications
USB standard
Rev. 1.0
Downstream power
Communication
*
Applies to 795FT plus
only(A6~A7page).
USB
port
supply
speed
complied self-powered
500mA for each
12
1
Mbps (full),
Mbps (low)
Upstream port
4 Downstream
A7
(MAX)
1.5
ports
hub
Operation
Location and Function of Controls
Front View
?
?
?
Power Button
Power Indicator
SET Button
Buttons
OSD Button
Rear View
ID Label
?
?
?
USB upstream port
*
Applies to
795FT
plus only.
?
USB downstream ports
AC Power
Socket
A8
*
D-Sub
Signal
Cable
*
Operation
Control Panel Function
Front Panel Controls
Power Indicator
OSD Button
Use this button to enter
exit the
on screen
The power indicator
or
light
is shown in the
power button. This indicator
display.
when the monitor
lights
up green
operates normally. If the
monitor is in DPM
(Energy Saving) mode
(stand-by/ suspend/ off), this indicator color
changes to amber.
?
?
OSD
SET
??
?
?
?
?
Buttons
Power Button
Use these buttons to
Use this button to enter
choose
a
in the
A9
SET Button
or
adjust
on screen
items
display.
selection in the
screen
display.
on
Use this button to turn
the monitor
on or
off.
Operation
On Screen
Display (OSD) Control Adjustment
Making adjustments to the image size, position and operating
parameters of the monitor are quick and easy with the On Screen
Display Control system. A quick example is given below to familiarize
you with the use of the controls. Following section is an outline of the
available adjustments and selections you can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
making image
adjustment.
To make
adjustments
in the On Screen
Display,
SET
OSD
OSD
1
2
acces a
control,
want becomes
A10
SET
Touch the OSD Button, then the main
To
3
Use the
4
Accept
5
5
Exit the OSD
the
follow these steps:
use
the
highlighted,
or
of the OSD appears.
Buttons. When the icon you
touch the SET Button.
Buttons to
changes by touching
by touching
menu
adjust
the item to the desired level.
the SET Button.
the OSD Button.
Operation
On Screen
Display(OSD) Selection and
Adjustment
You
item
introduced to the
were
procedure of selection and adjusting an
using the OSD system.
SET
OSD
Listed below
items that
OSD
are
are
the
icons, icon names, and icon descriptions of the
shown
on
the Menu.
SET
OSD
Adjust
Description
BRIGHTNESS CONTRAST
BRIGHTNESS/CONTRAST
Brightness
Used to
adjust
the
brightness
of the
screen.
66
92
Contrast
the
desired.
Adjust
COLOR
COLOR
PRESET
6500K
PRESET
displays
color
temperature.
?6500K:Slightly
?9300K:Slightly
RED
GREEN
BLUE
POSITION
reddish white.
bluish white.
TEMP
User easily color set without
adjustment Red, Green and Blue
(R/G/B).
RED
To set your
own
color levels.
GREEN
To set your
own
color levels.
BLUE
To set your
own
color levels.
Vertical Position
To
66
45
move
image
up and down.
Horizontal Position
To
move
right.
A11
to the contrast
6500K/ 9300K
To appear the
9300K
TEMP
POSITION
display
picture image
left and
Operation
On Screen
Display(OSD) Selection and
Adjustment
SET
OSD
OSD
SET
OSD
Adjust
Description
SIZE
Vertical Size
To
49
SIZE
adjust image height.
64
Horizontal Size
To
SHAPE
adjust image
width.
Side Pincushion
To correct the
bowing
in and out of the
image.
Side
SHAPE
pincushion
balance
To correct the balance of both sides
bowling.
Trapezoid
SHAPE
To correct
geometric
distortion.
Parallelogram
This control
of the
Top
adjusts for
image.
skewing
Corner
To correct the
the
a
screen
irregular
displayed image.
distortion of
Bottom Corner
To correct the
the
irregular
displayed image.
distortion of
Tilt
To correct
Pin W
image
rotation.
Adjust
To correct the balance of both sides
W
bowing.
Pin S
Adjust
To correct the balance of both sides
S
A12
bowing.
Operation
On Screen
Display(OSD) Selection and
Adjustment
SET
OSD
OSD
SET
OSD
Adjust
Description
SETUP
VIDEO LEVEL
0.7V
DDC
ON
LANGUAGE
ENGLISH
OSD POSITION
SETUP
CLAMP
SEP
BEEP
ON
VIDEO LEVEL This item is used to select the
monitor's input signal level. The
normal level used for most PC's is
0.7V.
When the screen suddenly gets
brightened or blurry, please select
1.0V and try again.
DDC
LANGUAGE
To select the DDC
function(ON/OFF).
To choose the language in which
the control names are displayed.
OSD Menus
are
available in 8
language: English, Deutsch,
Francais, Espanol, Italiano,
Svenska, Suomi and Portugues.
OSD POSITION To adjust position of the OSD
window on the screen.
CLAMP
In
case
Green)
of
input SOG(Sync On
Signal, the back
Video
raster will appear the green.
to select the
BEEP
A13
SOG(Sync
clamp, will
original back
On
Then,
Green)
in the
take you back to
the
raster.
To select
beep
ON
or
OFF.
Operation
On Screen
Display(OSD) Selection and
Adjustment
SET
OSD
OSD
SET
OSD
Adjust
Description
SPECIAL
DEGAUSS
DEGAUSS
ON
RECALL
ON
MOIRE
H:0V:0
CONVERGENCE
H:50
PURITY
50
To
manually demagnetize
screen
image
the
which may show some
or color incorrectly.
54.4kHz/60.0Hz
USER MODE
SPECIAL
RECALL
If the monitor is operating in a
factory preset mode, this control
will reset the image to the factory
preset mode.
MOIRE
This item allows you to reduce the
moire (Moire is caused by
interference Horizontal Scan Line
with the
periodical dot screen). It is
normally OFF(H:0/V:0).
The moire adjustments may affect
the focus of the
The
slightly
screen.
may shake
while the moire reduction
screen
function is
image
on.
CONVERGENCE This item allows you to adjust the
horizontal convergence.
The horizontal convergence control
adjust the alignment of the red and
blue horizontal fields.
PURITY
Use to
the
adjust the overall purity
image if the color appears
uneven.
A14
of
Energy Saving Design
complies with the EPA's Energy Star program, which is a
program designed to have manufacturers of computer equipment build
circuitry into their products to reduce power consumption during time of
This monitor
non-use.
This monitor also goes into its energy saving mode if you exceed the
monitor's operating limits, such as the maximum resolution of 1600x1200
or
the
frequency
refresh rates of 30-96kHz horizontal
When this monitor is used with
with
a
Green
or
50-160Hz vertical.
Energy Star PC, or a PC
the VESA Display Power
or
EPA
blanking software following
Management Signalling (DPMS) protocol, this monitor can conserve
significant energy by reducing power consumption during periods of nonuse. When the PC goes into the energy saving mode, the monitor will go
into a suspended operation state, indicated by the Power LED light
changing from a green color to an amber color. After an extended period
in the suspended mode, the monitor will then enter a semi-OFF mode to
a screen
energy. In the semi-OFF mode or DPMS OFF mode as we
specifications, the Power LED will still show an amber color.
conserve more
call it in
our
When you awaken your PC by hitting a key or moving the mouse, the
monitor will also awaken to its normal operating mode, indicated by the
green Power LED
consumption
Power
can
light. By following
be reduced to the
these conventions, the power
following levels:
Consumption
≤110W(120W)
Green
≤
8W(30W)
Amber
Off
≤
8W(30W)
Amber
Off
≤
3W(20W)
Amber
*(
):withUSB
Normal(Max.)
On
On
Normal
Stand-by
Off
On
Off
Suspend
On
Off
Off
Off
Off
Technical Information
Low Radiation Compliance (MPR II) and
DDC (Display Data Channel)
Low Radiation
This monitor meets
Compliance
(MPR II)
Sweden, limit the
Frequency (ELF)
DDC
one
of the strictest
guidelines
available
today for
low
radiation emissions, offering the user extra shielding and an antistatic
screen coating. These guidelines, set forth by a government agency in
(Display Data
Channel)
DDC is
a
amount of emission allowed in the
and
Very
Low
Extremely Low
Frequency (VLF) electromagnetic range.
communication channel
over
which the monitor
automatically
informs the host system (PC) about its capabilities. This monitor has two
DDC function; DDC1 and DDC2B. DDC1 and DDC2B carry out unidirectional communication between the PC and the monitor. Under these
situations, the PC sends display data to the monitor but not commands to
control the monitor
settings.
NOTE
PC must
support DDC functions to do this.
If your monitor is displaying a mono chrome
select the DDC OFF function.
A16
image or the wrong resolution,
Video
Memory Modes
The monitor has 37 memory locations for display
are factory preset to popular video modes.
Display Modes
(Resolution)
User Modes
modes, 12 of which
832
x
624
49.725
75
VESA 1280
x
1024
79.976
75
123456789
VESA
720
x
400
31.469
70
VESA
640
x
480
31.469
60
VESA
640
x
480
43.269
85
MAC
1152
870
68.681
75
1024
91.146
85
864
77.487
85
MAC
VESA 1280
VESA
x
x
1152
x
VESA 1600
x
1200
93.750
75
10
VESA
800
x
600
53.674
85
11
VESA
1024
x
768
60.023
75
12
VESA
1024
x
768
68.677
85
Modes 13-37
detects
one
are
empty and
can
accept
new
video data. If the monitor
video mode that has not been present before or is not
of the preset modes, it stores the new mode automatically in one
a new
of the empty modes
If you
use
starting
with mode 13.
up the 25 blank modes and still have
more new
modes, the monitor replaces the information in the
user
video
modes
starting
with mode 13.
Recalling Display
Modes
When your monitor detects a mode it has seen before, it automatically
recalls the image settings you may have made the last time you used
that mode.
You may, however, manually force a recall of each of the 12 preset
modes by pressing the Recall button. All preset modes are
automatically
recalled
as
the monitor
senses
the
incoming signal.
The
ability to recall the preset modes is dependent on the signal
coming from your PC's video card or system. If this signal does not
match any of the factory modes, the monitor automatically sets itself
display the image.
to
Technical Information
Troubleshooting
Check the
following before calling for service.
SELF DIAGNOSTICS message.
The signal cable is not connected.
OUT OF FREQUENCY message appears.
The frequency of the sync input is outside the operating range of the
monitor.
*Horizontal
*Vertical
Frequency : 30-96kHz
Frequency : 50-160Hz
Use the
graphics board's utility software to change
setting (Refer to the manual for graphics board).
the
frequency
The power LED is illuminated amber.
Display power management mode.
There is
no sync signal and the signal cable is not fastened securely.
Check the computer power and graphics adapter configuration.
The
or
image on the SCREEN
rectangle shape.
is not centered,
or
too
small,
not a
Image adjustment
not been done
Use the OSD, SET and
yet in the current operating mode.
buttons to set the
The monitor doesn't enter the power
image
to your
saving off
mode
liking.
(Amber).
Computer video signal
is not VESA DPMS standard. Either the PC
the video controller card is not
using
or
the VESA DPMS power
management function.
NOTE
If the power indicator(LED)
condition of the monitor.
light
is
blinking amber,
Then press a power ON/OFF button on the front
service technician for more information.
A18
may result in abnormal
panel
control and call your
Service
Unplug the monitor from the wall outlet and refer servicing to
qualified service personnel when :
The power cord or plug is damaged or frayed.
Liquid has been spilled into the monitor.
The monitor has been exposed to rain or water.
The monitor does not operate normally following the operating
instructions. Adjust only those controls that are covered in the
operating instructions. An improper adjustment of other controls may
result in damage and often requires extensive work by a qualified
technician to restore the monitor to normal operation.
The monitor has been dropped or the cabinet has been damaged.
The monitor exhibits a distinct change in performance.
Snapping or popping from the monitor is continuous or frequent while
the monitor is operating. It is normal for some monitors to make
occasional sounds when being turned on or off, or when changing
video modes.
Do not attempt to service the monitor
removing
covers
hazards. Refer all
yourself, as opening or
dangerous voltage or other
qualified service personnel.
may expose you to
servicing
to
Technical Information
Specifications
Sync Signal Types
H.Sync.
V.Sync.
Separate Sync.
H.
V.
Composite Sync.
H/V.
Priority
Type
123
(N.C
Signal Connector
Pin Assignment
Sync.
No
:
On Green
Sync.
Sync.
N.C.
Sync.
N.C.
N.C.
Connection)
15pin VGA Connector
5
1
6
10
15
Pin
NOTE
12345678
11
Signal(D-Sub)
Red
9
N.C.
Green
10
Ground
Blue
11
Ground
Ground
12
SDA
Self-Test
13
H.
Sync.
Red Ground
14
V.
Sync.
Green Ground
15
SCL
Blue Ground
No. 5 Pin have to
A20
Pin
Signal(D-Sub)
ground
on
the PC side.
Technical Information
Specifications
Picture Tube
17 inch
90
(16.0 inches viewable)
degree deflection
Perfect Flat Tube
0.24mm Slot
pitch
W-ARAS(Wide Anti-Reflective Anti-Static) coating
Sync Input
Horizontal
30
Vertical
50
Input
Freq.
Freq.
Form
Input
96kHz
160Hz
(Automatic)
(Automatic)
Input Form
Separate, RGB Analog, 0.7Vp-p/75 ohm,
Resolution(max) 1600 x 1200 @75Hz
Dimensions
(with tilt/swivel stand)
Power
-
Separate TTL, Positive/Negative
Composite TTL, Positive/Negative
SOG (Sync On Green)
15 pin D-Sub Connector
Signal Input
Video
-
Input
Width
41.50
cm
/ 16.3 inches
Height
Depth
43.90
cm
/ 17.3 inches
43.50
cm
/ 17.1 inches
Europe
AC 200-240V 50Hz 1.5A
Others
The
Positive
AC100-240V 50/60Hz 2.0A
products
should be used
according
to the Power
requirements
of each ID LABEL.
Weight
Net
Environmental Conditions
19.2
kg ( 42.3lbs)
Condition
Operating
Temperature
Humidity
10 ˚C to 40 ˚C
10 % to 90 %
non-Condensing
Storage Condition
0 ˚C to 60 ˚C
Temperature
5 % to 90 % non-Condensing
Humidity
NOTE
Information in this document is
A21
subject
to
change without
notice.
Download PDF

advertising