LG STUDIOWORKS 520SI(CB550BN) Owner’s Manual
LG STUDIOWORKS-520SI-CB550BN is a color monitor with a range of features designed to enhance your computing experience. It boasts a user-friendly control panel for easy adjustment of image settings. The monitor's tilt and swivel base allows for flexible positioning, ensuring optimal viewing angles. With its compliance to MPR II standards, it ensures reduced radiation emissions for a healthier work environment. Enjoy vivid visuals and clear display with LG STUDIOWORKS-520SI-CB550BN.
PDF
Download
Document
Advertisement
Advertisement
019S/cover99.11.252:55PM˘`1 Colour Monitor USER GUIDE BENUTZERHANDBUCH MANUEL D'UTILISATION GUIDA UTENTE GUIA DEL USUARIO StudioWorks 520Si http://www.lge.co.kr P/NO : 3828TUL019S (S-9805) AGENCY REGULATORY NOTICE FCC Compliance Statement This equipment has comply with the limits been tested and found to for a Class B digital device to Part 15 of the FCC Rules. These limits pursuant are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by using one or more of the following measures: - - - - Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by LG Electronics Inc. for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded Signal System. i Cables may be used with this Canadian D.O.C. Notice Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This Cet appareil numerique de la classe B respecte exigences du Reglement sur le materiel toutes les brouilleur du Canada. CE Conformity Notice Products with the "CE" Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive (73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity following European Norms : to the ? ? ? ? ? EN 55022 EN 50082-1:1992 EN 60555-2 EN 60555-3 EN 60950 ; Radio ; Frequency Interference Electromagnetic Immunity ; Power Line Harmonics ; Voltage ; Product ii Fluctuations Safety Table of Contents Monitor Registration Notice .......................................................................................................A1 Trademark Important On Acknowledgments..................................................................A1 Precautions safety..................................................................................................A2 On installation ..........................................................................................A3 On On cleaning..............................................................................................A3 repacking............................................................................................A3 Tilt/Swivel Base Installation ................................................................................................A4 Installation Connections .............................................................................................A5 Control Layout and Descriptions Front View ................................................................................................A6 Rear View ................................................................................................A6 Image Control Power Panel ................................................................................A7 Management System, MPR II and DDC Power Management System ....................................................................A9 Low Radiation Compliance (MPR II)........................................................A9 DDC (Display Data Channel) ...................................................................A9 General Video Operation Memory Modes ............................................................................A10 Troubleshooting and Service Troubleshooting......................................................................................A11 Service ...................................................................................................A12 Specifications..........................................................................................A13 iii Monitor Registration The model and serial numbers These numbers You should record as a are found on the rear of this unit. to this unit and not available to others. unique requested are permanent record of your information here and retain this purchase. Staple your receipt Date of Purchase : Dealer Purchased From : Dealer Address : Dealer Phone No. : Model No. : Serial No. : guide here. Notice All rights reserved. Reproduction in any manner, in whole or in part, strictly prohibited without the written permission of LG Electronics Inc. Trademark LG is IBM a is Acknowledgments trademark of LG Electronics Inc. is a registered trademark and VGA is International Business Machines WARNING expose this : To reduce appliance AVERTISSEMENT : Cela peut entrainer un a trademark of Corporation. the risk of fire or electric shock, do not to rain or moisture. Ne pas placer cet appareil dans un endroit humide. incendie ou une decharge electrique. A1 Important Precautions This unit has been engineered and manufactured to assure your personal safety, but improper use can result in potential electrical shock or fire hazard. In order not to defeat the safeguards incorporated in this monitor, observe the following basic rules for its installation, use, and servicing. Also follow all warnings and instructions marked directly on your monitor. On safety 1. Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable standards (UL/CSA or VDE) if not being provided by the supplier. 2. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. 3. Operate the monitor only from a power source indicated in the specifications of this manual or listed on the monitor. If you are not sure what type of power supply you have in your home, consult with your dealer. 4. Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement. 5. DO NOT OPEN THE MONITOR. There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the monitor is not operating properly. 6. To avoid personal injury : Do not place the monitor on a sloping shelf unless properly secured. Use only a stand recommended by the manufacturer. Do not try to roll a stand with small casters across thresholds or deep pile carpets. 7. To prevent Fire Always or Hazards: turn the monitor OFF if you leave the room for more than a short period of time. Never leave the monitor ON when the house. A2 leaving Precautions Important children from Keep cabinet Do not dropping or pushing objects into the monitor's openings. Some internal parts carry hazardous voltages. add accessories that have not been designed for this monitor. During storm or when the monitor is to be left lightning a unattended for extended an period of time, unplug it from the wall outlet. Do not the bring magnetic picture tube. devices such magnets as or motors near On installation 1. Do not allow do not place 2. Do not anything to rest upon or roll over the power cord, and the monitor where the power cord is subject to damage. use this monitor near water such as near a washbowl, kitchen sink, laundry tub, in a wet basement, bathtub, or near a swimming pool. 3. Monitors are openings in the cabinet to generated during operation. If these blocked, built-up heat can cause failures which may provided with ventilation allow the release of heat openings are result in fire hazard. Therefore, NEVER: a Block the bottom ventilation slots by placing the monitor on a bed, sofa, rug, etc. Place the monitor in is provided. openings Cover the Place the monitor On a built-in enclosure unless proper ventilation with cloth or near or over a other material. radiator or heat source. cleaning cleaning the face of the picture tube. slightly damp (not wet) cloth. Do not use an aerosol directly on the picture tube because overspray may cause Unplug Use the monitor before a electrical shock. On repacking Do not throw away the carton and packing materials. They make ideal container in which to transport the unit. When shipping an the unit to another location, repack A3 it in its original material. Tilt/Swivel Base Turn Off the Carefully equipment and all attached options. set the monitor face-down with the underside facing you. Installation 1. Align the hooks on the tilt/swivel stand with the matching slots in the base of the monitor. 2. Insert the hooks into slots. 3. Slide the tilt/swivel stand toward the front of the monitor until the latches click into the locked position. Hole Hooks Hooks Latch A4 Installation supply voltage is marked on the ID label located on the rear panel of the monitor. If your local voltage is different, do not use the monitor and contact your supplier before using the display. The Connections To connect your monitor after the video 1. Turn OFF the power to your 3. Connect board 4. on panel the properly installed: computer so that you can easily get of each. signal your PC is computer and all its attached options. 2. Position the monitor and the to the back adapter as cable with D-sub connector to the graphics described in your PC Owner's Manual. Tighten the screws on from coming loose and the video cable connectors to to keep them prevent radio and TV interference. 5. Connect the power cord to the AC receptacle on the back of the monitor. Plug the other end of the power cord into a properly grounded electrical outlet. 6. The socket-outlet should be installed should be easily near the equipment accessible. D-15P Power Cord Signal A5 Cable and Control Layout and Descriptions Front View Power On/Off Button Power Indicator Image Control Panel Brightness Contrast Rear View ID Label AC Power Connector Signal A6 Cable Control Layout and Description Power On/Off Button This Button is used to turn the power On or Off. Power Indicator The power indicator lights when the power is On, and indicates the operating status of the display. Contrast the display to the contrast desired. Move the thumbwheel located beneath this indicator to increase or decrease the display Adjust contrast. Brightness Used to adjust the brightness of the screen. Move the thumbwheel located beneath this indicator to increase or decrease the display brightness. Image Control Panel 3 2 1 1 Image Selection and Use either the or adjust 2 and Adjustment buttons button to select the icons which you wish to display. -/+ buttons Used to set values for each of the select item button for increment digital by pressing + A7 or - on screen control button for decrement. Image 3 Image Control Listed below Control Panel Icons the icons, icon names, and icon are descriptions of the items. icon Description Horizontal Position To move - + Horizontal Size To To To width. Increases the size of the image image. image. screen screen up and down. Moves the screen Moves the screen image image down. up. Decreases the size of the Increases the size of the To correct the - + - bowing Curves the Curves the To correct + * screen right. image left. image right. adjust image height. - + Trapezoid Moves the move + Side Pincushion screen left and Decreases the size of the - Vertical Size Moves the adjust image - + Vertical Position picture image in and out of the image's edges image's edges geometric image. image. screen screen image. inwards. outwards. distortion. Makes the screen Moves the screen image image narrower at the wider at the top. top. Recall Function When the user wants to recall one of the 6 fatory fixed image modes, push the and + buttons simultaneously. To recall the next image mode, press both the and + buttons again. - - A8 Power Management System conjunction with a PC having power saving circuitry, or screen blanking software this monitor automatically reduces its power consumption when the computer is not in use.The monitor has power-saving states, indicated by the light-emitting diode (LED) on the front panel.These power-saving states exceed the Environmental Protection Agency (EPA) Energy Star requirements using the methodology for Display Power Management Signals(DPMS). Developed by the Video Electronics Standards Association(VESA). When used in a PC running Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limits the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. DDC (Display DDC is a Data Channel) communication automatically informs the host channel over system(PC) which about its the monitor capabilities.This monitor has DDC2B function; DDC2B carry out uni-directional communication between PC and monitor. Under these situations, the PC sends monitor NOTE : display servings. data to the monitor but not commands to control the PC must support DDC functions to do this. Some older computer systems are not compatible with the DDC standard. If your monitor is displaying a monochrome image or the wrong resolution, compatible VGA card. A9 need to change with a DDC General After Operation the installation instructions and following controls, you 1. Turn are ready to the monitor, PC and other on getting peripherals you plan 2. After the PC has booted enter a software familiar with the operate the monitor. (powered up and application that uses the full to use. finished screen self-testing), display. 3. While looking at the image on the screen, adjust the controls for image size, centering, brightness and contrast levels you prefer. the 4. This monitor is with a variety an auto scanning monitor, capable of synchronizing automatically. The Scanning of video standards Mode Table below indicates the resolution, as well as the horizontal and vertical refresh rates, of some of the modes that this monitor can match to the output of your PC's graphics card. Other resolutions and standards can also be synchronized and displays this monitor on and vertical as frequency range long as they are within the horizontal of this monitor. See the specifications for this information. Video Memory Mode Display 1 640 x 2 640 3 Modes Horizontal Vertical Frequency Frequency 480 31.47 kHz 60 Hz x 480 43.27 kHz 85 Hz 720 x 400 31.47 kHz 4 800 x 600 5 800 x 600 6 1024 x Mode 768 Polarity Horiz Sinc Vert Sinc - - - - 70 Hz - + 37.88 kHz 60 Hz + + 53.67 kHz 85 Hz + + 48.36 kHz 60 Hz A10 - Troubleshooting Symptom: Possible The power LED is amber. causes: Display power management mode. There is no sync signal. The signal cable is not fastened securely. Check the computer power and graphics adapters configuration. The frequency of the sync input is outside the operating range of the monitor. HORZ: 30kHz-54kHz VERT: 50Hz-120Hz Symptom: The image on or not a rectangle shape. Possible Causes: the SCREEN is not centered, Image adjustment not been done or yet in the mode. Use the SELECT and +/- buttons to set the operating your liking. Symptom:The (Amber led). Possible monitor doesn't enter the power Causes:Computer standard. Enter the PC or video signal saving A11 current image to off mode is not VESA DPMS the video controller card is not VESA DPMS power management function. too small using the Service 1. Unplug the monitor from the wall outlet and refer service personnel The power cord Liquid has been when servicing to alified : plug is damaged or frayed. spilled into the monitor. The monitor has been exposed to rain or water. The monitor does not operate normally following the operating instructions. Adjust only those controls that are covered in the operating instructions. An improper adjustment of other controls may result in damage and often requires extensive work by a qualified technician to restore the monitor to normal operation. The monitor has been dropped or the cabinet has been damaged. The monitor exhibits a distinct change in performance. Snapping or popping from the monitor is continuous or frequent while the monitor is operating. It is normal for some monitors to make occasional sounds when being turned on or off, or switching video modes. 2. Do not attempt or to service the monitor yourself, as opening or removing may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. covers A12 Specifications Sync Signal type Type Separate Signal sync Connector Pin H. Sync V. Sync H. Sync V. Sync Assignment Pin 1 5 6 11 Separate Sync 10 15 1 Red 2 Green 3 Blue 4 Ground 5 Self-Test 6 Red Ground 7 Green Ground 8 Blue Ground 9NC 10 Ground 11 Ground 12 SDA 13 14 Horiz.Sync Vert.Sync 15 SCL A13 Specifications Picture tube : 15 inch 90 (13.8 degree inches viewable), Tinted, deflection 0.28 mm, Non-Glare Horizontal screen 54 kHz : 30 : 50 Video Bandwidth : 65 MHz Resolution : 1024 Signal connector : 15 Power input : 100-240VAC, 50/60Hz, 1.5A Power Consumption Vertical Frequency Frequency MODE ~ ~ 120 Hz x 768 Non Interlace, 60Hz Refresh Rate pin D-Sub type Table H.sync V.sync Power Video LED Color Consumption Normal On On On ≤ 85W Green Stand-by Suspend Off On Off ≤ 15W Amber On Off Off ≤ 15W Amber Off Off Off Off ≤5W Amber Dimensions : (WXDXH) Weight (net) : 360 represent a commitment 386 x 378 mm 14.2 x 12.5 kg (27.6 lbs) Information in this document is not x on 15.2 subject x (With Tilt/Swivel 14.9 inch to change without notice and does the part of LG Electronics Inc. A14 Stand)) ">

Public link updated
The public link to your chat has been updated.
Advertisement