Thank you for purchasing a high resolution monitor. It will give you high resolution performance and convenient reliable operation in a variety of video operating modes. Features The monitor is 17 inches (15.9 inches viewable ) intelligent, microprocessor compatible analog RGB (Red, Green, Blue) display standards, including IBM PC , PS/2 , Apple , Macintosh , Centris , Quadra , and Macintosh II family. a based monitor with most The monitor provides crisp text and vivid color graphics with VGA, SVGA, XGA, Ergonomic modes (non-interlaced), and most Macintosh compatible color video cards when used with the appropriate adaptor. The monitor's wide compatibility makes it possible to upgrade video cards or software without purchasing a new monitor. and VESA Digitally controlled auto-scanning is done with the micro-processor for horizontal frequencies between 30 and 96kHz, and vertical scan frequencies scan between 50-160Hz. This monitor is dots and a capable of producing a maximum horizontal resolution of 1600 maximum vertical resolution of 1200 lines. The microprocessor-based digital controls allow you to adjust conveniently a variety of image controls by using the OSD (On Screen Display). Plug and play capability if supported by your system This monitor has DDC 1 and DDC 2B function.* Compliant with - - - the following regulated specifications :* EPA ENERGY STAR Swedish MPR II Swedish TCO'99 * For detailed information, please refer to the Reference Guide provided . Connecting the Monitor On the back of the monitor power 1 2 cord, are plug-in connections; one for the AC signal cable from the video card. two and the other for the Power off both the monitor and PC. Connect the 15 pin VGA connector of VGA video connector on the supplied signal cable to the output only one way. If the PC. The connectors will mate you cannot attach the cable easily, turn the connector upside down and try again. When mated, tighten the thumbscrews to secure the connection. 2' appropriate MAC to VGA adapter block at your local computer adapter changes the high density 3 row 15 pin VGA connector to the correct 15 pin 2 row connection to mate with your MAC. Attach the other end of the signal cable to the side of the adapter block with 3 rows. Locate the store. This Connect the attached cable to the video output adapter block/signal on your MAC. 3 One end of the AC power cord is connected into the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. 4 5 Power ON the PC, then the monitor. If you see the SELF DIAGNOSTICS message, check the signal cable and connectors. 6 After using the system, power OFF the monitor, then the PC. IBM PC MACINTOSH 2' 2 Mac D-15P Adapter MAC6 D-15P 3 Power Cord Signal Cable * NOTE : For Apple Macintosh use, separate plug adapter is needed change the 15 pin high density (3 row) on the supplied pin 2 row connector. D-sub VGA connector cable to A2 a 15 a to Location and Function of Controls Front View Front Panel Controls Rear View ID Label D-Sub AC Power Socket A3 Signal Cable Control Panel Function Front Panel Controls Button Power (DPMS) Indicator Power Button Brightness Buttons Button Contrast Control Function Button Use this button to enter or exit the on screen display. Buttons Use these buttons to choose the Button on screen Use this button to enter adjust items in a selection in the on display. screen Brightness Used to Contrast Adjust Power (DPMS) Indicator This Indicator adjust the the display brightness of the screen. to the contrast desired. lights up green when the monitor operates normally. If the monitor is in DPM (Energy Saving) mode this indicator color Power Button or display. (stand-by/suspend/off), changes to amber. Use this button to turn the monitor A4 on or off. On Screen Display (OSD) Control Adjustment Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system. A quick example is given below to familiarize you with the use of the controls. Following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the monitor to stabilize for at least 30 minutes before To make 12 3 45 adjustments Press the To control, use highlighted, Use the Accept Display, Button, then the main acces a becomes in the On Screen the the Buttons to changes by pressing Exit the OSD by Pressing the follow these steps: of the OSD appears. Buttons. When the icon you want or press the menu making image adjustment. Button. adjust the the item to the desired level. Button. Button. A5 On Screen You were Display(OSD) introduced to the Selection and Adjustment procedure of selection and adjusting an item the OSD using descriptions system. Listed below are the icons, icon names, and icon of the items that are shown on the Menu. OSD Adjust Description H POSITION To 43.2kHz/85Hz H move POSITION 50 picture image Moves the screen Moves the screen left and right. left. image image right. U H SIZE To 43.2kHz/85Hz H adjust image width. SIZE Decreases the size of the 50 screen image. Increases the size of the U screen image. V POSITION To 43.2kHz/85Hz V move image up and down. POSITION 50 Moves the screen Moves the screen image image down. up. U V SIZE 43.2kHz/85Hz V To SIZE adjust image height. Decreases the size of the 50 screen image. Increases the size of the U screen image. PINCUSHION 43.2kHz/85Hz To correct the PINCUSHION image. bowing in and out of the 50 Curves the image's edges inwards. U Curves the outwards. A6 image's edges On Screen Display(OSD) OSD Selection and Adjust Adjustment Description TRAPEZOID 43.2kHz/85Hz To correct TRAPEZOID geometric Makes the 50 at the the screen image narrower screen image wider at top. Moves the U distortion. top. PIN BALANCE To correct the balance of both sides 43.2kHz/85Hz PIN BALANCE bowing. 50 Curvature of the sides to the right. Curvature of the sides to the left. U PARALLELOGRAM 43.2kHz/85Hz This control PARALLELOGRAM the screen 50 adjusts image. Tilts the screen Tilts the screen U for a skewing of image leftward. image rightward. TILT To correct 43.2kHz/85Hz image rotation. TILT 50 Tilts the screen Tilts the screen image left. image right. U H MOIRE 43.2kHz/85Hz Reduce horizontal moire when H interference MOIRE patterns of dark steady wary lines appear on your screen. The moire adjustments may affect the focus of the screen. 0 U V MOIRE 43.2kHz/85Hz Reduce vertical moire when V interference MOIRE patterns of dark steady wary lines appear on your screen. The moire adjustments may affect the focus of the screen. 0 U A7 On Screen Display(OSD) OSD Selection and Adjust Adjustment Description H CONVERGENCE This item allows you to adjust the horizontal convergence. 43.2kHz/85Hz H CONVERGENCE The horizontal convergence control adjust the alignment of the red and 50 blue horizontal fields. U COLOR ? 9300 : To appear the display's color temperature. Slightly ? 6500 : To appear the display's color temperature. K : 43.2kHz/85Hz COLOR bluish white. Slightly reddish white. Temperature range is from U ? 5000K to 10000K. So, user easily color set without 43.2kHz/85Hz COLOR 9300 6500 K adjustment Red, Blue (R/G/B). RGB ? RGB Green and To set your own color levels. Allow for specific : adjustments to Red, and Blue (R/G/B). ? Green To exit the COLOR OSD. : RECALL You can use 43.2kHz/85Hz this function when you want to go back to the RECALL display purchased the product adjusting to modify it in the screen of the time you after Preset Mode. U When you can are in the User mode, you recall only using Recall, adjust the display again if necessary. , , , items. After screen If you want more information on Preset Mode, refer to A10 page. A8 the On Screen Display(OSD) OSD Selection and Adjust Adjustment Description LANGUAGE 43.2kHz/85Hz To choose the LANGUAGE control language in which displayed. the names are OSD Menus available in 8 are languages : English, German, French, Spanish, Italian, Svenska, Suomi and Portugues. U 43.2kHz/85Hz LANGUAGE ENGLISH DEUTSCH AIS FRANC ESPAN OL ITALIANO VIDEO LEVEL 43.2Hz/85Hz VIDEO This item is used to select the LEVEL monitor's 0.7V 1.0V input signal level. The normal level used for most PC's is 0.7V. When the screen suddenly gets brightened or blurry, please select 1.0V and try again. U DEGAUSS 43.2kHz/85Hz To manually demagnetize the some image incorrectly. screen DEGAUSS which may show or 43.2kHz/85Hz To inform user INFORMATION mode data. color U INFORMATION U 43.2kHz/85Hz INFORMATION PRESET MODE 1 43.2kHz / 85Hz 2 53.6kHz / 85Hz 3 68.6kHz / 85Hz 4 91.1kHz / 85Hz 5 93.7kHz / 75Hz A9 users of preset and : USER MODE : PRESET MODE The monitor has 30 memory locations for factory preset to popular video modes. display modes, 5 of which are Preset Modes (Resolution) 1 2345 VESA 640 x VESA 800 x VESA 480 43.269 85 600 53.674 85 768 68.677 85 VESA 1280 x 1024 91.146 85 VESA 1600 x 1200 93.750 75 1024 x User Modes Modes 6-30 are empty and can accept new video data. If the monitor detects a video mode that has not been present before or is not one of the preset modes, it stores the new mode automatically in one of the empty modes new starting with mode 6. If you use up the 25 blank modes and still have more new video modes, the monitor replaces the information in the user modes starting with mode 6. Recalling Display Modes When your monitor detects a mode it has seen before, it automatically recalls the image settings you may have made the last time you used that mode. You may, however, manually force a recall of each of the 5 preset modes by pressing the Recall button. All preset modes are automatically recalled as the monitor The senses ability to the incoming signal. recall the preset modes is dependent on the signal coming from factory your PC's video card or system. If this signal does not match any of the modes, the monitor automatically sets itself to display the image. Check the following before calling for service. SELF DIAGNOSTICS message. The signal cable is not connected, or is loose. Check and secure the connection. OUT OF FREQUENCY message appears. The frequency of the signal from the video card is outside the operating range of the monitor. * * Horizontal Frequency : 30-96kHz Vertical Frequency : 50-160Hz Use the graphics to the manual for board's utility software graphics board). to change the frequency setting (Refer The power LED is illuminated amber. Display power management mode. There is no active signal coming from the PC. The signal cable is not fastened securely. Check the computer power and graphics image on the SCREEN rectangle shape. The Image adjustment and adapter configuration. is not centered, not been done yet in the buttons to set the image or too current to your The monitor doesn't enter the power operating liking. saving off small, or not a mode. Use the mode (Amber). Computer video signal is not VESA DPMS standard. Either the PC or the video controller card is not using the VESA DPMS power management function. , Specifications Picture Tube 17 inch 90 (15.9 degree inches viewable) FST deflection 0.26mm dot pitch ARAS(Anti-Reflective Anti-Static) coating, U-coating Horizontal Sync Input Vertical Input 30 Freq. 50 Freq. - 96kHz (Automatic) 160Hz (Automatic) Separate TTL, Positive/Negative Composite TTL, Positive/Negative Form - SOG (Sync On Green) 15 pin D-Sub Connector Signal Input Video Input Form Separate, RGB Analog, 0.7Vp-p/75 ohm, Resolution(max) 1600 x 1200@75Hz Input Power Normal ≤ 110W Consumption Stand-by/Suspend ≤ Power Off ≤3W Width 41.6 cm / 16.4 inches Height Depth 43.2 cm / 17.0 inches 44.0 cm / 17.3 inches Europe AC 200-240V 50Hz 1.5A Dimensions tilt/ swivel Power (with stand) Input Others The 8W AC 100-240V 50/60Hz 2.0A should be used products requirements of according to the Power each ID LABEL. Weight Net Environmental Operating Condition 10 ˚C to 40 ˚C Temperature 10 % to 90 % non-Condensing Humidity Storage Condition 0 ˚C to 60 ˚C Temperature 5 % to 90 % non-Condensing Humidity Conditions 18 kg (39.68 lbs) NOTE Information in this document is Positive subject to change without A12 notice.