LG | MCD102 | LG MCD202 Owner’s Manual

HISPANO_MCD102-202_ENG_MFL36641616
MINI Hi-Fi SYSTEM
OWNER’S MANUAL
MODEL: MCD202
MCD202-A0U/D0U/X0U
MCS202F
MCD102
MCD102-A0U/D0U/X0U
MCD102-A0/D0/X0
MCS102F
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and
completely.
USB
Safety Precaution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation and
to ensure reliable operation of the product and to protect it from
over heating.
The openings should be never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's
instruction has been adhered to.
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain it for future reference. Should the unit
require maintenance, contact an authorized service center.
Use of controls, adjustments or the performance of procedures
other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the
enclosure. Visible laser radiation when open. DO NOT STARE
INTO BEAM.
2
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as
vases, should be placed on the apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance
and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or
damaged wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such
as being twisted, kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall outlets, and the point
where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord
plug. When installing the product, ensure that the plug is easily
accessible.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste
stream via designated collection facilities appointed
by the government or the local authorities.
3. The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your
old appliance, please contact your city office, waste
disposal service or the shop where you purchased
the product.
This product is manufactured to comply with the
EEC DIRECTIVE 89/336/EEC, 93/68/EEC and
2006/95/EC.
POWER SAVE MODE
You can set up the unit into an economic power save mode.
In the power-on status, press and hold 1/] (POWER) button for
about 3 seconds.
- Nothing is displayed in the display window when the unit
goes into the power save mode.
To cancel power save mode, press 1/ ] (POWER).
Contents
Before use
About the Symbols for instruction /
Notes on Discs / Notes on Tapes . . . . . . . .3
Front / Back Panel . . . . . . . . . . . . . . . . . .4
Remote Control . . . . . . . . . . . . . . . . . . . . .5
Notes on Discs
Before use
Before use
Handling discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on
the disc.
Connections
Speaker System Connections /
Antenna (Aerial) Connections /
Auxiliary Function . . . . . . . . . . . . . . . . . . .6
Operation
USB Function - OPTIONAL /
About MP3/WMA . . . . . . . . . . . . . . . . . . .7
Audio Adjustment / Setting the Clock . . . . .8
Timer Function / Sleep Timer Function . . .9
Presetting the Radio Stations /
Listening to the Radio . . . . . . . . . . . . . . .10
RDS Function - OPTIONAL . . . . . . . . . . .11
Tape Playback / Tape Recording . . . . . . .12
CD Playback . . . . . . . . . . . . . . . . . . . . . .13
To Program Play / Repeat /
To check MP3/WMA file information . . . . .14
Storing discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
Cleaning discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the
disc from the center outward.
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . .15
Specifications . . . . . . . . . . . . . . . . . . . . .16
About the symbols for
instruction
Indicates hazards likely to cause harm to
the unit itself or other material damage.
Indicates special notes and operating
Note
features.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available
cleaners, or anti-static spray intended for older
vinyl records.
Notes on Tapes
Preventing record
Removing the tab(s) of the cassette (with a small
screwdriver) will prevent accidental erasure.
Side A
Tab for side A
Tab for side B
To record again, cover the hole of the tab with an
adhesive tape.
Adhesive tape
3
Front / Back Panel
1
12
2
11
3
10
4
9
5
8
6
7
13
14
16
15
1. DISPLAY WINDOW
2. • 1/ ] (POWER) button
• Z OPEN/CLOSE button
3. • XDSS/MP3 OPT. button
• XTS - PRO button
4. • USB (OPTIONAL)/DEMO button
•
USB connector (OPTIONAL)
• PHONES (HEADPHONE JACK)
: 3.5mm
5. • TUNER button
• AUX button
6. Z PUSH EJECT position - TAPE 1
7. Z PUSH EJECT position - TAPE 2
8. • TUNING (-/+) buttons
bb/B
BB (REWIND/FAST FORWARD)
buttons
bb/B
BB> (CD SKIP/SEARCH)
.b
buttons
• PRESET (-/+) buttons
B) button
FORWARD PLAY (B
• x STOP button
4
9. • CD button
• TAPE button
10. • CLOCK button
• TIMER button
• RDS(OPTIONAL)/SET/CD[] button
• EQ. button
• CD SYNC./DUBB/ST./MONO button
• REC/ [] button
• VOLUME CONTROL KNOB
11. DISC SELECT (DISC1, DISC2, DISC3) buttons
12. DISC TRAY
13. AM/FM ANTENNA TERMINAL
14. AUX IN (AUXILIARY INPUT) connector
15. POWER CORD
16. SPEAKER TERMINAL
Before use
Remote Control
MUTE button
POWER button
PRESET/FOLDER(
) buttons
• USB (OPTIONAL) button
• FUNCTION button
VOLUME (
) buttons
SLEEP button
DIMMER button
CD FUNCTION buttons
PLAY/PAUSE (B
B/ []) button •
CD STOP(x) button •
CD SKIP/SEARCH •
bb/B
BB>) buttons
(.b
TUN.(-/+) buttons •
REPEAT button •
D.SKIP button
EQ button •
XTS Pro button •
XDSS plus button •
NUMERIC buttons
3
Detach the battery cover on
the rear of the remote control,
and insert two R03 (size AAA)
batteries with 3 and #
aligned correctly.
AAA
AAA
Remote Control battery installation
PROGRAM/MEMO button
TAPE FUNCTION buttons
B) button
• FORWARD PLAY (B
bb) button
• FAST REWIND PLAY (b
BB) button
• FAST FORWARD PLAY (B
• TAPE-1/2 SELECT buttons
• RECORD/RECORD PAUSE (z/ [])
button
• TAPE STOP (x) button
RANDOM button
INFO (MP3/WMA file information
display) button
Remote Control Operation Range
Point the remote control at the remote sensor
and press the buttons.
• Distance : About 23 ft (7 m) from the front of
the remote sensor.
• Angle
: About 30° in each direction of the
front of the remote sensor.
#
Caution
Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).
5
Connections
Speaker System Connections
Connect the speaker cables to the speaker terminal.
Front speaker
(Right)
Front speaker
(Left)
Notes:
• Be sure to match the speaker cord to the appropriate terminal on the components: + to + and – to –.
If the cords are reversed, the sound will be distorted and will lack base.
• If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speaker.
• Connect the Left/Right speaker correctly. If it reversed, the sound may be distorted.
Antenna (Aerial) Connections
Auxiliary Function
Connect the supplied FM/AM antennas for
radio reception.
Connect an auxiliary device such as a TV or VCR
via the rear mounted AUX connector and press
FUNCTION.
FM wire antenna (supplied)
To AUDIO in
AM(MW)
loop antenna
(aerial) (supplied)
For AM(MW) reception,
connect the loop antenna
(aerial) to the terminal marked AM.
Notes:
• To prevent noise pickup, keep the AM loop
antenna away from the unit and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it
as horizontal as possible.
6
Auxiliary Device
To AUDIO out
Note:
Turn the unit off and then connect an auxiliary
device before you connect an auxiliary device.
Because it may be made a noise.
USB Function - OPTIONAL
You can enjoy MP3/WMA media file saved on
MP3 player or USB memory device by connecting the device to the USB port of this unit.
USB Memory, MP3 Player
(or Memory Card Reader,
etc.)
Compatible Devices
1. Devices which require additional program
installation when you have connected it to a
computer, are not supported.
2. MP3 Player : Flash type MP3 player.
• The MP3 player requiring installation of a driver
is not supported.
3. USB Flash Drive : Devices that support
USB2.0 or USB1.1.
Basic Playback
1. Connect the USB device to the USB connector of your unit.
2. Press USB to select USB function.
“CHECKING” appears in the display window,
and then the total number of files is displayed.
3. Press PLAY/PAUSE (B/[[]).
In addition, you can also play using the
NUMERIC buttons.
To Remove the USB from the unit
1. Choose an other function except USB
in order to remove the USB.
2. Remove the USB from the unit.
Note:
Besides Basic Playback, if you want to operate
other functions, see the CD Playback section.
Moving to other cards
In the case that more than two memory cards
are connected to the USB port, press D.SKIP on
the remote control to select a cards you want to
use.
Notes:
• Do not extract the USB device in operating.
• A back up demands to prevent a data damage.
• If you use a USB extension cable or USB hub,
the USB device might not be recognized.
• A device using NTFS file system is not
supported (Only the FAT (16/32) file system is
supported.).
• The USB function of this unit does not support
all USB devices.
• Digital camera and mobile phones are not
supported.
• This unit is not supported when the total
number of files is 1000 or more.
Operation
Operation
About MP3/WMA
MP3/WMA Disc compatibility with this unit is
limited as follows:
1. Sampling Frequency
8 - 48kHz(MP3), 32 - 48kHz(WMA)
2. Bit rate
8 - 320kbps(MP3), 48 - 320kbps(WMA)
3. CD-R physical format should be “ISO 9660”
4. If you record MP3/WMA files using the software which cannot create a FILE SYSTEM,
for example “Direct-CD” etc., it is impossible
to playback MP3 files. We recommend that
you use “Easy-CD Creator”, which creates
an ISO 9660 file system.
5. File names should be named using 30 letters or less and must incorporate
“.mp3”,“.wma” extension e.g. “********.MP3”
or “********.WMA”
6. Do not use special letters such as
“/ : * ? “ < >”etc.
7. Even if the total number of files on the disc
has more than 1000, it will only be shown
up to 999.
About MULTI SESSION
- This function recognizes the multi session disc
according to a disc of CD-ROM type.
ex) If there are MP3/WMA files in the first session, the MP3/WMA file in the first session
are only played.
If there are only MP3/WMA files in the
whole session, all of the MP3/WMA files in
the session are played.
If there is an Audio CD in the first session,
only the Audio CD in the first session is
played.
7
XDSS plus
(Extreme Dynamic Sound System)
Connect a stereo headphone plug ( 3.5 mm) into
the headphone jack to listen to the sound through
headphones. The speakers are automatically disconnected when you plug in the headphones (not
supplied).
MUTE
Press MUTE to temporarily stop the sound.
The “ ” indicator flashes in the display window.
To cancel it, press VOLUME (
again.
) or MUTE
EQUALIZER Effect
DRAMA
→
→
JAZZ
→
→
You can choose 7 fixed sound impressions and
adjust the BASS, MIDDLE and TREBLE.
- You can select a desired sound mode by using
EQ. on the front panel or EQ on the remote
control.
NORMAL → USER EQ → POP → CLASSIC
ROCK
MP3 Optimizer
This function is optimized for compressible MP3
file. It improves the bass sound to make sweet
sound.
Each time you press MP3 OPT. on the front
panel the setting changes in the following order.
XDSS ON → MP3 -- OPT ON → NORMAL
DIMMER
This function is turns off the LED (Light-emitting
diode) on the front panel and darkens the display
window by half in power-on status.
Press DIMMER once.
To cancel it, press DIMMER again.
8
XTS Pro
This unique sound quality developed by our
technology creates the optimum sound for you to
play the perfect playback of the original sound
and to feel the living sound source.
Each time you press XTS Pro the setting
changes in the following order.
XTS -- PRO ON ↔ XTS -- PRO OFF
Note:
The XTS Pro function will not be operated when
a headphone has been connected.
DEMO
Press DEMO in power off state to demonstrate
the function in the display window. To cancel it,
press / ] (POWER) or DEMO again.
Setting the Clock
1. Press CLOCK.
2. Select a 24 hour time system or a 12 hour
time system by pressing .bb/BB>.
v v v v v v v v
v v
- Press EQ. or EQ to select USER EQ.
1. When USER EQ is displayed, press SET.
“BASS 0” will be appeared in the display
window.
2. Press .bb/BB> to select the setting
you want (MIN, -4 ~ +4, MAX steps).
3. Select the BASS, MIDDLE or TREBLE you
want by press PRESET (-/+) on the front
panel.
4. Adjust the MIDDLE and TREBLE as shown
above.
Press XDSS on the front panel to reinforce treble, bass and the surround effect. The “XDSS
ON” or “NORMAL” indicator lights.
Or press XDSS plus on the remote control.
Audio CD : XDSS ON ↔ NORMAL
MP3/WMA : XDSS ON → MP3 -- OPT ON
→ NORMAL → XDSS ON ...
v v
Headphone jack
or
v v v v v v v
Audio Adjustment
(12HR)
(24HR)
3. Press SET to confirm the selected hour time
system.
4. Press .bb/BB> on the front panel to
set the correct hours.
5. Press SET.
6. Press .bb/BB> on the front panel to
set the correct minutes.
7. Press SET and the correct time is shown on
the display window.
8. Press CLOCK at any time, to display the
time for about 5 seconds.
Note:
If you want to reset the clock, press and hold
CLOCK for more than 2 seconds.
With the TIMER function you can have the radio
reception, CD play, TAPE play and USB (in the
USB supplied models) play turned on and off at
the desired time.
1. Press CLOCK to check the current time.
(If you don’t set clock, the timer function
doesn’t work.)
2. Press TIMER to enter the timer setting
mode.
If you want to correct the previously
memorized TIMER setting, press and hold
the TIMER for more than 2 seconds.
- The previous memorized time and “ ”
indicator appear in the display window.
3. Each function [TUNER → CD → USB (in the
USB supplied models) → TAPE] flashes in
the display window in turn. Press SET when
the desired function is flashing.
4. a. 1) When you select the TUNER function,
‘PLAY’ and ‘REC’ indicator flash in the
display window alternately for about 3
seconds.
‘PLAY’ indicator : TUNER play only
‘REC’ indicator : TUNER play and
recording
2) Press SET when the desired function
is flashing.
3) Select the previous memorized preset
number with .bb/BB> and
press SET.
b. When you select the CD, TAPE or USB (in
the USB supplied models) function,
- ‘ON TIME’ indicator appears for about
0.5 seconds in the display window and
then disappears.
5. Set the hour to switch on by pressing
.bb/BB> on the front panel.
6. Press SET.
7. Set the minute to switch on by pressing
.bb/BB> on the front panel.
8. Press SET to confirm the minute to switch on.
- ‘OFF TIME’ indicator appears for about
0.5 seconds in the display window and
then disappears.
9. Set the hour to switch off by pressing
.bb/BB> on the front panel.
10. Press SET.
11. Set the minute to switch off by pressing
.bb/BB> on the front panel.
12. Press SET.
13. Adjust the volume level by pressing
.bb/BB> on the front panel.
14. Press SET.
“ ” appears in the display window and the
timer setting has been completed.
15. Switch the system off.
The selected function is automatically
switched on and off at the time set.
To cancel or check the timer
Each time TIMER is pressed, you can select the
timer set or cancel. You can also check the timer
setting status.
To activate or check the timer, press TIMER so
that “ ” appears in the display window.
To cancel the TIMER, press TIMER so that “ ”
disappears in the display window.
Operation
Timer Function
Sleep Timer Function
When the sleep timer is used, the power is
automatically turned off after the specified time
has elapsed.
1. Press SLEEP to set the desired sleep time.
The SLEEP indicator and sleep time appear
in the display window.
2. Each time you press SLEEP, the setting
changes in the following order.
SLEEP 180 → 150 → 120 → 90 → 80
→ 70 → 60 → 50 → 40 → 30 → 20 → 10
→ OFF (No display) → SLEEP 180 ...
Note:
If you press SLEEP while the sleep time is
displayed, the SLEEP time is reset.
To cancel the sleep timer mode
If you have to stop the function, press the
SLEEP repeatedly until “SLEEP 10” appears,
and then press SLEEP once again while “SLEEP
10” is displayed.
9
Presetting the Radio Stations
You can preset 50 stations for FM and AM.
1. Press TUNER on the front panel or FUNCTION on the remote control to select the frequency (AM or FM) you want.
2. Select a station you want by using TUNING
(-/+) on the front panel. Or press the TUN.
(-/+) on the remote control.
Tuning in automatically
- Press TUNING (-/+) on the front panel for
more than 0.5 second.
Or press TUN. (-/+) on the remote control
for more than 0.5 second. Scanning stops
when the unit tunes in a station.
Tuning in manually
- Press TUNING (-/+) on the front panel
[Or press TUN. (-/+) on the remote control]
briefly and repeatedly.
3. Press PROGRAM/MEMO on the remote
control. A preset number will flash in the display window.
4. Press PRESET (-/+) [or PRESET/FOLDER
(
) on the remote control] to select the
preset number you want.
5. Press PROGRAM/MEMO again.
The station is stored.
6. Repeat the steps 1 (or 2) to 5 to store other
stations.
To delete all the memorized stations
Press and hold PROGRAM/MEMO on the
remote control for two seconds, “ERASE ALL”
appears in the display window.
And then PROGRAM/MEMO on the remote
control again, the stations are deleted.
For your reference
If all stations have already been entered, “FULL”
message will appear in the display window for a
moment and then a preset number will flash.
To change the preset number, follow the steps
4 - 5.
To recall presets
Press and hold PRESET/FOLDER (
) on
the remote control until the desired preset number appears. Or press it repeatedly.
10
Listening to the Radio
1. Press TUNER on the front panel or FUNCTION on the remote control to select the frequency (AM or FM) you want.
The last received station is tuned in.
2. Press PRESET/FOLDER (
) on the
remote control repeatedly to select the preset station you want.
- Each time you press the button, the unit
tunes in one preset station at a time.
3. Adjust the volume by rotating the VOLUME
control knob [or pressing VOLUME
(
) on the remote control] repeatedly.
To listen to non-preset radio stations
• For manual tuning, see “Tuning in manually” in
the step 2 on the left.
• For automatic tuning, see “Tuning in automatically” in the step 2 on the left.
To turn off the radio
Press 1/ ] (POWER) to turn the unit off or select
another function mode [CD, AUX, TAPE, USB (in
the USB supplied models)].
For your reference
• If an FM program is noisy;
Press ST./MONO so that “STEREO”
disappears in the display window. There will be
no stereo effect, but the reception will be
improved. Press ST./MONO again to restore
the stereo effect.
• To improve reception;
Reposition the supplied antennas.
About RDS
This unit is equipped with RDS (Radio Data
System), which brings a wide range of
information to FM radio. RDS, now in use in
many countries, is a system for transmitting
station call signs or network information, a
description of station programme type text
message about the station or specifics of musical
selection and the correct time.
RDS Tuning
When a FM station is tuned in and it contains
RDS data, the unit will automatically display the
station’s call sign and the RDS indicator will light
in the Display Window as well as indicators for
the programme type recognition (PTY), Radio
Text (RT), Clock Time (CT) and RDS services
programme (PS) if transmitted by the station.
RDS Display Options
The RDS system is capable of transmitting a
wide variety of information in addition to the initial
call sign that appears when a station is first
tuned. In normal RDS operation the display will
indicate the station name, broadcast network or
call letters. Pressing RDS enables you to cycle
through the various data types in the sequence:
(FREQUENCY → PTY → RT → CT → PS)
• PTY (Programme type recognition)- The name
of the programme type is shown in the Display
Window.
• RT (Radio text recognition)- The name of the
radio text is shown in the Display Window.
• CT (Time controlled by the channel)- Enables
the unit to receive the actual time and show it
in the Display Window.
• PS (Programme Service name)- The name of
the channel is shown in the Display Window.
Note:
Some RDS stations may not choose to include
some of these additional features. If the data
required for the selected mode is not being transmitted, the Display Window will show a PTY
NONE, RT NONE, CT NONE or PS NONE
message.
Programme Search (PTY)
A major benefit of RDS is its ability to encode
broadcasts with Programme Type (PTY) codes
that indicate the type of material being broadcast. The following list shows the abbreviations
used to indicate each PTY along with an explanation of the PTY.
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
EASY M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATION M
OLDIES
FOLK M
DOCUMENT
TEST
ALARM !
News
Current Affairs
Information
Sports
Educational
Drama
Culture
Science
Varied Speech Programme
Popular Music
Rock Music
Easy Listening Music
Light Music
Classical Music
Other Music
Weather Information
Financial Programmes
Children’s Programmes
Social Affairs Programmes
Religious Broadcasts
Phone-In Programmes
Travel and Touring
Leisure and Hobby
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary Programmes
Station Alarm Test Message
Emergency Broadcast Information
Operation
RDS Function - OPTIONAL
You may search for a specific Programme Type
(PTY) by following these steps.
1. Press TUNER (or FUNCTION) to select FM
mode.
2. Press RDS, the display will show the last
PTY in use.
3. Press PRESET (-/+) repeatedly to select a
desired PTY.
4. When the PTY is selected, press and hold
TUNING (-/+). The unit will go into an automatic search mode.
5. When a station is tuned, the search will
stop.
11
Tape Playback
Tape Recording
Use only normal tapes.
Wind the tape to the point recording starts.
Use only normal tapes.
Basic Playback
1. Press TAPE (or FUNCTION) to select
TAPE function.
(“NO TAPE” appears in the display
window.)
2. Load a tape.
B).
3. Press PLAY(B
To Stop Play
Press x STOP during playback.
To Play Rewind or Fast Forward
After pressing .bb/BB> on the front
panel or bb/BB on the remote control during
B) at the point you want.
playback, press PLAY(B
AUTO STOP DECK (TAPE 1/2)
After auto stop deck plays only the front side, the
unit stops automatically.
Dubbing
This function shows how to record from tape to
tape.
1. Press TAPE (or FUNCTION) to select tape
function.
• Cassette TAPE 1- Insert a playback tape to
dub.
• Cassette TAPE 2- Insert a blank tape.
2. Press DUBB as shown below.
To stop dubbing, press x STOP.
Basic Setting
1. Select a function you want to record except
tape function.
2. Open the cassette TAPE 2 and insert a
blank cassette into the cassette compartment.
General Recording
1. Press REC/[[] on the front panel or z/[] on
the remote control.
- “REC” flashes and holds the cassette in
pause mode.
2. Press REC/[[] on the front panel or z/[] on
the remote control again, then press PLAY
B) to start playing the source you want to
(B
record. The recording begins.
To pause recording
Press z/[] during recording.
- “REC” flashes in the display window.
To stop recording
Press x STOP.
CD to Tape Synchronized Recording
The CD synchro recording function dubs a complete CD and programmed titles automatically
into a cassette.
1. Press CD and load a disc you want to
record.
2. Press CD SYNC. in stop mode.
“REC” flashes and “CD SYNC” indicator
lights.
3. The synchronized recording is started
automatically after about 7 seconds.
Notes:
• If you wish to record from the desired track,
select the desired track with CD SKIP/
SEARCH (.bb/BB>) before
commencing CD synchro recording.
• You cannot change any mode during
recording.
12
Note:
To load an 8cm (3 inch) disc, put it onto the inner
circle of the tray.
3. Press Z OPEN/CLOSE to close the disc
compartment.
Audio CD : “READING” appears in the display window, and then the total
number of tracks and the playing
time are displayed.
MP3/WMA CD : “READING” appears in the
display window, and then
the total number of files is
displayed.
B) on the front panel or
4. Press PLAY (B
PLAY/PAUSE (B
B/[[]) on the remote control.
In addition, you can also play an Audio CD
or MP3/WMA CD using the NUMERIC
buttons.
Pause Playback
Press CD[[] on the front panel or PLAY/PAUSE
(B
B/[[]) on the remote control during playback.
Press this button again to resume play.
Stop Playback
x)
Press x STOP on the front panel or CD STOP(x
on the remote control during playback.
Searching a Track
Press .bb/BB> on the front panel, and
then press once more at the point you want.
Or hold .bb/BB> on the remote control
during playback, then release at the point you
want.
Note:
This function is only available for Audio CD’s.
title
To select a disc directly
Press DISC SELECT or D.SKIP during playing
or stopping.
When you press DISC 1-3 before playing a disc,
the unit will automatically start playing the selected disc.
Operation
With the label side up
To exchange discs during playback
You can open the disc tray while playing a disc
to check what discs are to be played next and
exchange discs, without interrupting playback of
the current disc.
1. Press Z OPEN/CLOSE.
The disc tray is opened. Two disc compartments appear. Even if the unit is playing a
disc, it doesn’t stop playing.
2. Replace discs in the compartments with other
ones.
The unit plays the disc in the left compartment after the current disc, and then the
one in the right compartment.
3. Press Z OPEN/CLOSE.
The CD door closes.
title
DISC 1
To go to the next discs
Press DISC SELECT or D.SKIP during playing
or stopping.
Notes:
• Do not place more than one disc on one disc
tray at the same time.
• Do not push on the disc tray to close CD door,
you may damage the unit.
title
Basic Playback
1. Press CD (or FUNCTION) to select CD
function. If no disc is loaded then “NO
DISC” is displayed.
2. Press Z OPEN/CLOSE and place the disc
into the disc tray.
The disc on the left (DISC 1) is played first.
Skipping a Track
• Press BB> to go to the next track.
• When the .bb on the remote control is
pressed once midway through a track, the
player returns to the start of that track.
When it is pressed again, a track is skipped
each time the button is pressed.
RANDOM
Press RANDOM on the remote control during
playback. The tracks/files on the CD/MP3/WMA/
USB (in the USB supplied models) will all play in
random order.
“RANDOM” appears in the display window.
To cancel it, press RANDOM again.
MP3/WMA file folder function
Press PRESET/FOLDER (
) on the remote
control to select the folder you want.
Note:
It is applied in the case that has several folder in
MP3/WMA file.
title
CD Playback
13
To Program Play
Repeat
You can arrange the order of the tracks on the
discs and create your own program. The program can contain up to 20 tracks.
1. Press PROGRAM/MEMO on the remote
control on stop mode.
“PROG.” appears in the display window.
a. Audio/MP3/WMA CD
Press REPEAT during playback.
Audio CD
1) Press D.SKIP or DISC SELECT (DISC
1/2/3) to select the disc.
REPEAT ALL DISC :To play all tracks on all
discs repeat.
OFF(No display) : To cancel repeat play.
→
Program number
REPEAT DISC : To play one disc repeatedly.
→
Track Number
: To play one track repeatedly.
→
Disc Number
→REPEAT
MP3/WMA
→REPEAT
: To play one file repeatedly.
→
→
REPEAT FOLDER :To play one folder
repeatedly.
REPEAT DISC : To play one disc repeatedly.
→
2) Press .bb/BB> to select the
track.
→
REPEAT ALL DISC :To play all files on all discs
repeat.
OFF(No display) : To cancel repeat play.
b. USB (in the USB supplied models)
file Number
Program number
: To play one file repeatedly.
→
- Press .bb/BB> to select the file.
USB (in the USB supplied models)
→REPEAT
→
REPEAT FOLDER :To play one folder
repeatedly.
REPEAT ALL
: To play all files repeatedly.
To add program contents
1. Press PROGRAM/MEMO repeatedly in the
program stop mode until the Track Number
blinks.
2. Repeat the steps 2 - 4 above.
To modify program contents
1. Press PROGRAM/MEMO to display the
program number you want to modify.
2. Repeat the steps 2 - 4 above.
14
→REPEAT
: To play one track (file)
repeatedly.
REPEAT ALL DISC(CD)
or REPEAT ALL(USB) : To play all program
repeatedly.
OFF(No display) : To cancel program repeat
play.
→
To clear program contents
Press PROGRAM/MEMO on stop mode. And
x).
then press CD STOP(x
OFF(No display) : To cancel repeat play.
Program repeat play
→
To check program contents
Press PROGRAM/MEMO on stop mode.
- The disc, track and program number will be
displayed in the display window.
→
2. Press PROGRAM/MEMO.
3. Repeat the steps 1 - 2 above.
4. Press PLAY/PAUSE (B
B/[[]) on the remote
B) on the front panel.
control or PLAY (B
To check MP3/WMA file information
Press INFO during MP3/WMA file playback.
- The information (Title, Artist or Album) of the
MP3/WMA file will be shown in the display
window.
- If there is no the information of the MP3/WMA
file, “NO ID3 TAG” or “NO WMA TAG” indicator
will be shown in the display window.
Note:
This unit can play a CD-R or CD-RW that
contains audio titles or MP3/WMA files.
Reference
Troubleshooting
Cause
• The power cord is disconnected.
Reference
Correction
• Plug the power cord into the wall outlet
No power
securely.
• The audio cables are not connected
• Connect the audio cable into the jacks
securely.
securely.
• The power of the external source
• Switch on the external source
No sound
equipment is switched off.
equipment.
• The speaker cable is set to a wrong
• Set the speaker cable to the correct
position.
position, then turn on the unit again by
pressing POWER.
• An unplayable disc is inserted.
• Insert a playable disc.
• The disc is placed upside down.
• Place the disc with the playback side
down.
The unit does not
start playback • The disc is not placed within the guide. • Place the disc on the disc tray correctly
inside the guide.
• The disc is dirty.
• Clean the disc.
• The remote control is not pointed at the • Point the remote control at the remote
remote sensor of the unit.
sensor of the unit.
• The remote control is too far from the
• Operate the remote control within about
The remote
unit.
23 ft (7 m).
control does not
•
There
is
an
obstacle
in
the
path
of
the
•
Remove the obstacle.
work properly
remote control and the unit.
• The batteries in the remote control are • Replace the batteries with new ones.
exhausted.
Symptom
15
Specifications
General
Power supply
Power consumption
Net Weight
External dimensions (WxHxD)
Refer to the back panel of the unit.
Refer to the back panel of the unit.
5.57kg (MCD202 Model)
5.36kg (MCD102 Model)
273 x 371 x 326mm
Tuner
FM Tuning Range
Intermediate Frequency
Signal to Noise Ratio
Frequency Response
AM Tuning Range
Intermediate Frequency
Signal to Noise Ratio
Frequency Response
87.5 - 108.0MHz or 65 - 74MHz, 87.5 - 108.0MHz
10.7MHz
60/55dB
50 - 10000Hz
522 - 1620kHz or 520 - 1720kHz
450kHz
30dB
140 - 1800Hz
Amplifier
Output Power
T.H.D
Frequency Response
Signal-to-noise ratio
100W + 100W (MCD202 Model)
50W + 50W (MCD102 Model)
0.5%
40 - 20000Hz
75dB
CD
Frequency response
Signal-to-noise ratio
Dynamic range
40 - 20000Hz
75dB
75dB
Cassette tape player
Tape Speed
Wow Flutter
F.F/REW Time
Frequency Response
Signal to Noise Ratio
Channel Separation
Erase Ratio
3000 ± 3% (MTT-111. NORMAL-SPEED)
0.25% (MTT -111, JIS-WTD)
120sec (C-60)
250 - 8000Hz
43dB
50dB (P/B)/45dB (R/P)
55dB (MTT-5511)
Speakers
Speaker Name
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max. Input Power
Net Dimensions (WxHxD)
Net Weight (1EA)
MCS202F
Bass Reflex 2Way 2 Speaker
4Ω
60 - 20000Hz
84dB/W (1m)
100W
200W
220 x 342 x 270mm
3.46kg
MCS102F
Bass Reflex 2Way 2Speaker
4Ω
60 - 20000Hz
85dB/W (1m)
50W
100W
200 x 337 x 228mm
2.92kg
Designs and specifications are subject to change without notice.
P/NO : MFL36641616
Download PDF

advertising