LG | 47LN5400-TA | LG 47LN5400-TA Owner’s Manual

OWNER’S MANUAL
LED TV
*LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating
your set and retain it for future reference.
LN54**
LN565*
LA61**
P/NO : MFL67725403 (1302-REV01)
Printed in Korea
www.lg.com
2
TABLE OF CONTENTS
ENGLISH
ENG
TABLE OF CONTENTS
3
SAFETY INSTRUCTIONS
8
Viewing 3D Imaging (Only 3D models)
9
INSTALLATION PROCEDURE
9
ASSEMBLING AND PREPARING
9
11
12
13
14
14
15
17
18
Unpacking
Separate purchase
Parts and buttons
Lifting and moving the TV
Setting up the TV
- Attaching the stand
Mounting on a table
Mounting on a wall
Tidying cables
19
MAKING CONNECTIONS
19
20
20
21
21
22
22
22
23
Antenna connection
HDMI connection
Component connection
Composite connection
USB connection
Headphone connection
Audio Connection
- Digital optical audio connection
MHL connection
24
REMOTE CONTROL
26
USING THE USER GUIDE
27
MAINTENANCE
27
27
27
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
27
TROUBLESHOOTING
28
SPECIFICATIONS
34
LICENSES
34
OPEN SOURCE SOFTWARE NOTICE
34
EXTERNAL CONTROL DEVICE
SETUP
WARNING
yy If you ignore the warning message, you may
be seriously injured or there is a possibility of
accident or death.
CAUTION
yy If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
yy The note helps you understand and use the
product safely. Please read the note carefully
before using the product.
SAFETY INSTRUCTIONS
ENGLISH
ENG
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
yyDo not place the TV and/
or remote control in the
following environments:
--A location exposed to
direct sunlight
--An area with high humidity
such as a bathroom
--Near any heat source
such as stoves and other
devices that produce heat
--Near kitchen counters or
humidifiers where they can
easily be exposed to steam
or oil
--An area exposed to rain or
wind
--Near containers of water
such as vases
Otherwise, this may result in
fire, electric shock, malfunction
or product deformation.
yyDo not place the product
where it might be exposed to
dust.
This may cause a fire
hazard.
yyMains Plug is the TV
connecting/disconnecting
device to AC mains electric
supply. This plug must
remain readily attached and
operable when TV is in use.
yyDo not touch the power plug
with wet hands. Additionally,
if the cord pin is wet or
covered with dust, dry the
power plug completely or
wipe dust off.
You may be electrocuted
due to excess moisture.
yyMake sure to connect Mains
cable to compliant AC mains
socket with Grounded earth
pin. (Except for devices
which are not grounded on
earth.) Otherwise possibility
you may be electrocuted or
injured.
3
yyInsert power cable plug
completely into wall socket
otherwise if not secured
completely into socket, fire
ignition may break out.
yyEnsure the power cord does
not come into contact with
hot objects such as a heater.
This may cause a fire or an
electric shock hazard.
yyDo not place a heavy object,
or the product itself, on
power cables.
Otherwise, this may result in
fire or electric shock.
yyBend antenna cable between
inside and outside building
to prevent rain from flowing
in.
This may cause water
damaged inside the Product
and could give an electric
shock.
yyWhen mounting TV onto wall
make sure to neatly install
and isolate cabling from
rear of TV as to not create
possibility of electric shock /
fire hazard.
yyDo not plug too many
electrical devices into a
single multiple electrical
outlet.
Otherwise, this may result in
fire due to over-heating.
yyDo not drop the product
or let it fall over when
connecting external devices.
Otherwise, this may result
in injury or damage to the
product.
4
SAFETY INSTRUCTIONS
ENGLISH
ENG
yyKeep the anti-moisture
packing material or vinyl
packing out of the reach of
children.
Anti-moisture material is
harmful if swallowed. If
swallowed by mistake, force
the patient to vomit and
visit the nearest hospital.
Additionally, vinyl packing
can cause suffocation. Keep
it out of the reach of children.
yyDo not spray water on the
product or scrub with an
inflammable substance
(thinner or benzene). Fire or
electric shock accident can
occur.
yyDo not let your children climb
or cling onto the TV.
Otherwise, the TV may
fall over, which may cause
serious injury.
yyNever touch this product or
antenna during a thunder or
lighting storm.
You may be electrocuted.
yyDispose of used batteries
carefully to ensure that
a small child does not
consume them.
Please seek Doctor- Medical
Attention immediately if child
consumes batteries.
yyDo not insert any metal
objects/conductors (like
a metal chopstick/cutlery/
screwdriver) between power
cable plug and input Wall
Socket while it is connected
to the input terminal on the
wall. Additionally, do not
touch the power cable right
after plugging into the wall
input terminal.
You may be electrocuted.
(Depending on model)
yyDo not put or store
inflammable substances
near the product. There is
a danger of combustion/
explosion or fire due to
careless handling of the
inflammable substances.
yyDo not drop metallic objects
such as coins, hair pins,
chopsticks or wire into the
product, or inflammable
objects such as paper and
matches. Children must pay
particular attention.
Electrical shock, fire or injury
can occur. If a foreign object
is dropped into the product,
unplug the power cord and
contact the service centre.
yyDo not allow any impact,
shock or any objects to fall
into the unit, and do not drop
anything onto the screen.
You may be injured or the
product can be damaged.
yyNever touch the wall outlet
when there is leakage of
gas, open the windows and
ventilate.
It may cause a fire or a burn
by a spark.
yyDo not disassemble, repair
or modify the product at your
own discretion.
Fire or electric shock
accident can occur.
Contact the service centre
for check, calibration or
repair.
yyIf any of the following
occur, unplug the product
immediately and contact
your local service centre.
--The product has been
impacted by shock
--The product has been
damaged
--Foreign objects have
entered the product
--The product produced
smoke or a strange smell
This may result in fire or
electric shock.
SAFETY INSTRUCTIONS
yyApparatus shall not be
exposed to dripping or
splashing and no objects
filled with liquids, such as
vases, shall be placed on
the apparatus.
CAUTION
yyInstall the product where no
radio wave occurs.
yyThere should be enough
distance between an outside
antenna and power lines
to keep the former from
touching the latter even
when the antenna falls.
This may cause an electric
shock.
yyDo not install the product
on places such as unstable
shelves or inclined surfaces.
Also avoid places where
there is vibration or where
the product cannot be fully
supported.
Otherwise, the product may
fall or flip over, which may
cause injury or damage to
the product.
yyIf you install the TV on a
stand, you need to take
actions to prevent the
product from overturning.
Otherwise, the product may
fall over, which may cause
injury.
yyIf you intend to mount the product to a wall,
attach VESA standard mounting interface
(optional parts) to the back of the product. When
you install the set to use the wall mounting
bracket (optional parts), fix it carefully so as not
to drop.
yyOnly use the attachments / accessories
specified by the manufacturer.
yyWhen installing the antenna,
consult with a qualified
service technician. If not
installed by a qualified
technician, this may create
a fire hazard or an electric
shock hazard.
yyWe recommend that you
maintain a distance of
at least 2 to 7 times the
diagonal screen size when
watching TV.
If you watch TV for a long
period of time, this may
cause blurred vision.
yyOnly use the specified type
of battery.
This could cause damage to
the remote control.
yyDo not mix new batteries
with old batteries.
This may cause the batteries
to overheat and leak.
yyBatteries should not be exposed to excessive
heat. For example, keep away from direct
Sunlight , open fireplace and electric heaters.
yyDo not place non-rechargeable batteries in
charging device.
yyMake sure there are no
objects between the remote
control and its sensor.
yySignal from Remote Control
can be interrupted due to
external/internal lighting eg
Sunlight, fluorescent lighting.
If this occurs turn off lighting
or darken viewing area.
yyWhen connecting external
devices such as video game
consoles, make sure the
connecting cables are long
enough.
Otherwise, the product
may fall over, which may
cause injury or damage the
product.
yyDo not turn the product
On/Off by plugging-in or
unplugging the power plug to
the wall outlet. (Do not use
the power plug for switch.)
It may cause mechanical
failure or could give an
electric shock.
ENGLISH
ENG
yyUnplug the TV from AC
mains wall socket if you do
not intend to use the TV
for a long period of time.
Accumulated dust can cause
fire hazard and insulation
deterioration can cause
electric leakage/shock/fire.
5
6
SAFETY INSTRUCTIONS
ENGLISH
ENG
yyPlease follow the installation
instructions below to
prevent the product from
overheating.
--The distance between the
product and the wall should
be more than 10 cm.
--Do not install the product in
a place with no ventilation
(e.g., on a bookshelf or in
a cupboard).
--Do not install the product
on a carpet or cushion.
--Make sure the air vent is
not blocked by a tablecloth
or curtain.
Otherwise, this may result in
fire.
yyTake care not to touch the
ventilation openings when
watching the TV for long
periods as the ventilation
openings may become hot.
This does not affect the
operation or performance of
the product.
yyPeriodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer.
yyPrevent dust collecting on
the power plug pins or outlet.
This may cause a fire
hazard.
yyProtect the power cord from
physical or mechanical
abuse, such as being
twisted, kinked, pinched,
closed in a door, or walked
upon. Pay particular
attention to plugs, wall
outlets, and the point where
the cord exits the appliance.
yyDo not press strongly upon
the panel with a hand or
sharp object such as nail,
pencil or pen, or make a
scratch on it, as it may
cause damage to screen.
yyAvoid touching the screen or
holding your finger(s) against
it for long periods of time.
Doing so may produce some
temporary or permanent
distortion/damage to screen.
yyWhen cleaning the product
and its components, unplug
the power first and wipe it
with a soft cloth. Applying
excessive force may cause
scratches or discolouration.
Do not spray with water or
wipe with a wet cloth. Never
use glass cleaner, car or
industrial shiner, abrasives
or wax, benzene, alcohol
etc., which can damage the
product and its panel.
Otherwise, this may result in
fire, electric shock or product
damage (deformation,
corrosion or breakage).
yyAs long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
yyWhen unplugging the cable,
grab the plug and unplug it,
by pulling at the plug. Don’t
pull at the cord to unplug the
power cord from the power
board, as this could be
hazardous.
yyWhen moving the product,
make sure you turn the
power off first. Then, unplug
the power cables, antenna
cables and all connecting
cables.
The TV set or power cord
may be damaged, which
may create a fire hazard or
cause electric shock.
yyWhen moving or unpacking
the product, work in pairs
because the product is
heavy.
Otherwise, this may result in
injury.
SAFETY INSTRUCTIONS
yyRefer all servicing to
qualified service personnel.
Servicing is required when
the apparatus has been
damaged in any way, such
as power supply cord or
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus,
the apparatus has been
exposed to rain or moisture,
does not operate normally,
or has been dropped.
yyIf the product feels cold to
the touch, there may be
a small “flicker” when it is
turned on. This is normal,
there is nothing wrong with
product.
yyThe panel is a high
technology display product
with resolution of two million
to six million pixels. You
may see tiny black dots and/
or brightly coloured dots
(red, blue or green) at a
size of 1 ppm on the panel.
This does not indicate a
malfunction and does not
affect the performance and
reliability of the product.
This phenomenon also
occurs in third-party
products and is not subject
to exchange or refund.
yyYou may find different
brightness and colour of the
panel depending on your
viewing position(left/right/
top/down).
This phenomenon occurs
due to the characteristic
of the panel. It is not
related with the product
performance, and it is not
malfunction.
ENGLISH
ENG
yyContact the service centre
once a year to clean the
internal parts of the product.
Accumulated dust can cause
mechanical failure.
7
yyDisplaying a still image (e.g., broadcasting
channel logo, on-screen menu, scene from a
video game) for a prolonged time may cause
damage to the screen, resulting in retention of
the image, which is known as image sticking.
The warranty does not cover the product for
image sticking.
Avoid displaying a fixed image on your
television’s screen for a prolonged period (2
or more hours for LCD, 1 or more hours for
Plasma).
Also, if you watch the TV at a ratio of 4:3 for
a long time, image sticking may occur on the
borders of the panel.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
yyGenerated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to temperature and humidity. This noise is common for
products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a high-speed
switching circuit, which supplies a large amount
of current to operate a product. It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
8
SAFETY INSTRUCTIONS
ENGLISH
ENG
Viewing 3D Imaging (Only 3D
models)
WARNING
Viewing Environment
yy Viewing Time
-- When watching 3D contents, take 5 - 15 minute
breaks every hour. Viewing 3D contents for
a long period of time may cause headache,
dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or
chronic illness
yy Some users may experience a seizure or other
abnormal symptoms when they are exposed to a
flashing light or particular pattern from 3D contents.
yy Do not watch 3D videos if you feel nausea, are
pregnant and/ or have a chronic illness such as
epilepsy, cardiac disorder, or blood pressure disease,
etc.
yy 3D Contents are not recommended to those who
suffer from stereo blindness or stereo anomaly.
Double images or discomfort in viewing may be
experienced.
yy If you have strabismus (cross-eyed), amblyopia (weak
eyesight) or astigmatism, you may have trouble
sensing depth and easily feel fatigue due to double
images. It is advised to take frequent breaks than the
average adult.
yy If your eyesight varies between your right and left
eye, revise your eyesight prior to watching 3D
contents.
Symptoms which require discontinuation or
refraining from watching 3D contents
yy Do not watch 3D contents when you feel fatigue from
lack of sleep, overwork or drinking.
yy When these symptoms are experienced, stop using/
watching 3D contents and get enough rest until the
symptom subsides.
-- Consult your doctor when the symptoms persist.
Symptoms may include headache, eyeball
pain, dizziness, nausea, palpitation, blurriness,
discomfort, double image, visual inconvenience
or fatigue.
CAUTION
Viewing Environment
� Viewing Distance
- Maintain a distance of at least twice the screen
diagonal length when watching 3D contents.
If you feel discomfort in viewing 3D contents,
move further away from the TV.
Viewing Age
yy Infants/Children
-- Usage/ Viewing 3D contents for children under
the age of 5 are prohibited.
-- Children under the age of 10 may overreact
and become overly excited because their vision
is in development (for example: trying to touch
the screen or trying to jump into it. Special
monitoring and extra attention is required for
children watching 3D contents.
-- Children have greater binocular disparity of 3D
presentations than adults because the distance
between the eyes is shorter than one of adults.
Therefore they will perceive more stereoscopic
depth compared to adults for the same 3D
image.
yy Teenagers
-- Teenagers under the age of 19 may react with
sensitivity due to stimulation from light in 3D
contents. Advise them to refrain from watching
3D contens for a long time when they are tired.
yy Elderly
-- The elderly may perceive less 3D effect
compared to the youth. Do not sit closer to the
TV than the recommended distance.
Cautions when using the 3D glasses
� Make sure to use LG 3D glasses. Otherwise, you
may not be able to view 3D videos properly.
� Do not use 3D glasses instead of your normal
glasses, sunglasses or protective goggles.
� Using modified 3D glasses may cause eye strain or
image distortion.
� Do not keep your 3D glasses in extremely high or low
temperatures. It will cause deformation.
� The 3D glasses are fragile and are easy to be
scratched. Always use a soft, clean piece of cloth
when wiping the lenses. Do not scratch the lenses of
the 3D glasses with sharp objects or clean/wipe them
with chemicals.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
Image shown may differ from your TV.
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
The available menus and options may differ from the input source or product model that you are using.
New features may be added to this TV in the future.
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned
off if it will not be watched for some time, as this will reduce energy consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced,
and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to upgrade of product
functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm
width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your
TV’s USB port.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
ENGLISH
ENG
NOTE
yy
yy
yy
yy
yy
9
10
ASSEMBLING AND PREPARING
ENGLISH
ENG
Remote control and
batteries (AAA)
(See p.24, 25)
Owner’s manual
Cable holder
(Depending on model)
(See p.18)
Power Cord
Stand Screws
3EA, P5 x 25
4EA, M4 x 14
(Only LN54**, LN565*)
(See p.14)
Desk-mount Screw
(2EA : Only LA61**)
(1EA : Only
32/37/39/42/47/50/
60LN54**, LN565*)
(See p.16)
Stand Screws
8EA, M4 x 14
(Only LA61**)
(See p.14)
Desk-mount Cable
2EA
(Only LA61**)
(See p.16)
Bracket Screw
2EA, M4 x 8
(Only 32/42LA61**)
2EA, P4 x 8
(Only 50LA61**)
(See p.16)
Stand Body /
Stand Base
(Only LA61**)
(See p.14)
Stand Body /
Stand Base
(Only LN54**, LN565*)
(See p.14)
Cinema 3D Glasses
The number of 3D glasses may differ depending
on the model or country.
(Only LA61**)
ASSEMBLING AND PREPARING
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AG-F***
Cinema 3D glasses
Compatibility
AG-F***DP
Dual play glasses
LG Audio Device
LA61**
AG-F***
Cinema 3D glasses
•
AG-F***DP
Dual play glasses
•
LG Audio Device
•
LN54**, LN565*
The model name or design may be changed depending on the upgrade of product functions, manufacturer’s
circumstances or policies.
ENGLISH
ENG
Separate purchase
11
12
ASSEMBLING AND PREPARING
Screen
Only LA61**
OK
SETTINGS
INPUT
Power indicator and
Remote control sensor
Speakers
Buttons
Screen
Only LN54**, LN565*
OK
SETTINGS
INPUT
Power indicator and
Remote control sensor
Speakers
Buttons
Button
Description
H
Scrolls through
the saved programmes.
USB IN
S
the volume level.
Selects the highlighted menu option or confirms an input.
3 USB Appps
HAdjusts
H
Accesses the main menu, or saves your input and exits the menus.
Changes the input source.
H
Turns the power on or off.
NOTE
or off by selecting OPTION in the main menus.
yy You can set the power indicator light to onOK
SETTINGS
USB IN
INPUT
4(PC) 1 HDD IN 2 USB Hub
ENGLISH
ENG
Parts and buttons
ASSEMBLING AND PREPARING
Please note the following advice to prevent the
TV from being scratched or damaged and for safe
transportation regardless of its type and size.
yy When transporting a large TV, there should be at
least 2 people.
yy When transporting the TV by hand, hold the TV as
shown in the following illustration.
CAUTION
yy Avoid touching the screen at all times, as this may
result in damage to the screen.
yy It is recommended to move the TV in the box or
packing material that the TV originally came in.
yy Before moving or lifting the TV, disconnect the power
cord and all cables.
yy When holding the TV, the screen should face away
from you to avoid damage.
yy Hold the top and bottom of the TV frame firmly. Make
sure not to hold the transparent part, speaker, or
speaker grill area.
yy When transporting the TV, do not expose the TV to
jolts or excessive vibration.
yy When transporting the TV, keep the TV upright, never
turn the TV on its side or tilt towards the left or right.
yy Do not apply excessive pressure to cause flexing /
bending of frame chassis as it may damage screen.
ENGLISH
ENG
Lifting and moving the TV
13
14
ASSEMBLING AND PREPARING
ENGLISH
ENG
Setting up the TV
Image shown may differ from your TV.
Attaching the stand
LN54**, LN565*
LA61**
3EA
1
1
P5 x 25
4 EA
M4 x 14
Stand Body
Stand Body
Stand Base
Stand Base
2
2
3
3
4EA
M4 x 14
4EA
M4 x 14
ASSEMBLING AND PREPARING
15
yy When attaching the stand to the TV set, place the
screen facing down on a cushioned table or flat
surface to protect the screen from scratches.
yy Make sure that the screws are inserted correctly
and fastened securely. (If they are not fastened
securely enough, the TV may tilt forward after
being installed.)
Do not use too much force and over tighten the
screws; otherwise screw may be damaged and
not tighten correctly.
(This feature is not available for all models.)
The Kensington security system connector is located at
the rear of the TV. For more information of installation and
using, refer to the manual provided with the Kensington
security system or visit http://www.kensington.com.
Connect the Kensington security system cable between
the TV and a table.
NOTE
yy Remove the stand before installing the TV on a
wall mount by performing the stand attachment in
reverse.
Mounting on a table
1 Lift and tilt the TV into its upright position on a table.
-- Leave a 10 cm (minimum) space from the wall
for proper ventilation.
10 cm
10 cm
m
10 c
Adjusting the angle of the TV to suit view
(Only LA61**)
Swivel 15 degrees to the left or right and adjust the angle
of the TV to suit your view.
15
15
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
yy Do not place the TV near or on sources of heat,
as this may result in fire or other damage.
CAUTION
»»When adjusting the angle adof the product, watch
out for your fingers.
»»Personal injury may occur if hands or fingers are
pinched. If the product is tilted too much, it may fall,
causing damage or injury.
<Rear>
<Front>
ENGLISH
ENG
Using the Kensington security system
CAUTION
16
ASSEMBLING AND PREPARING
ENGLISH
ENG
Securing the TV to a table
Securing the TV to a wall
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
To secure the TV to a table, insert and tighten the
supplied screw on the rear of the stand.
(Only 32/37/39/42/47/50/60LN54**, LN565*)
(This feature is not available for all models.)
(Only LA61**)
1 Insert and tighten the eye-bolts, or TV brackets and
bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eyebolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly with a
sturdy rope.
Make sure to keep the rope horizontal with the flat
surface.

CAUTION
yy Make sure that children do not climb on or hang
on the TV.
2EA
M4 x 8 (Only 32/42LA61**)
P4 x 8 (Only 50LA61**)
CAUTION
(Only LA61**)
How to fix the TV to a table
1.Connect the Desk-mount Cables to the Stand
Base using the Bracket Screws.
2.Fix the Desk-mount Cables to a table using the
Desk-mount Screws.
3.Once the TV is fixed, move the table close to the
wall. Children may go in, causing injuries.
WARNING
yy To prevent TV from falling over, the TV should be
securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the TV
may cause injury.
NOTE
yy Use a platform or cabinet that is strong and large
enough to support the TV securely.
yy Brackets, bolts and ropes are not provided. You
can obtain additional accessories from your local
dealer.
ASSEMBLING AND PREPARING
yy If a television is not positioned in a sufficiently
stable location, it can be potentially hazardous
due to falling. Many injuries, particularly to
children, can be avoided by taking simple
precautions such as:
»» Using cabinets or stands recommended by
the manufacturer of the television.
»» Only using furniture that can safely support
the television.
»» Ensuring the television is not overhanging the
edge of the supporting furniture.
»» Not placing the television on tall furniture (for
example, cupboards or bookcases) without
anchoring both the furniture and the television
to a suitable support.
»» Not standing the televisions on cloth or other
materials placed between the television and
supporting furniture.
»» Educating children about the dangers of
climbing on furniture to reach the television or
its controls.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the
TV carefully and install the wall mount bracket on a solid
wall perpendicular to the floor. When you attach the
TV to other building materials, please contact qualified
personnel.
LG recommends that wall mounting be performed by a
qualified professional installer.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that
meet the VESA standard. Standard dimensions for the
wall mount kits are described in the following table.
Separate purchase(Wall Mounting Bracket)
Model
32LN54**
32LN565*
32LA61**
VESA (A x B)
200 x 100
Standard screw
M4
Number of screws 4
Wall mount bracket LSW130B
37/39/42LN54**
42LA61**
200 x 200
M6
4
LSW230B
Model
47/50/55/60LN54**
50LA61**
VESA (A x B)
400 x 400
Standard screw
M6
Number of screws
4
Wall mount bracket LSW430B
A
B
ENGLISH
ENG
WARNING
17
18
ASSEMBLING AND PREPARING
ENGLISH
ENG
CAUTION
yy Disconnect the power first, and then move or
install the TV. Otherwise electric shock may occur.
yy If you install the TV on a ceiling or slanted wall, it
may fall and result in severe injury.
Use an authorized LG wall mount and contact the
local dealer or qualified personnel.
yy Do not over tighten the screws as this may cause
damage to the TV and void your warranty.
yy Use the screws and wall mounts that meet the
VESA standard. Any damages or injuries by
misuse or using an improper accessory are not
covered by the manufacturer’s warranty.
Tidying cables
(Only LA61**)
1 Use Cable Holder to neatly secure and position
cables together.
2 Fix the Cable Management firmly to the TV.
NOTE
yy Use the screws that are listed on the VESA
standard screw specifications.
yy The wall mount kit includes an installation manual
and necessary parts.
yy The wall mount bracket is not provided. You can
obtain additional accessories from your local
dealer.
yy The length of screws may differ depending on the
wall mount. Make sure to use the proper length.
yy For more information, refer to the manual supplied
with the wall mount.
Cable Management
Cable Holder
(Only LN54**, LN565*)
Use Cable Holder to neatly secure and position cables
together.
Cable Holder
CAUTION
yy Do not move the TV by holding the cable holder,
as the cable holders may break, and injuries and
damage to the TV may occur.
MAKING CONNECTIONS
This section on MAKING CONNECTIONS
mainly uses diagrams for the LN54** models.
Connect various external devices to the TV and switch
input modes to select an external device. For more
information of external device’s connection, refer to the
manual provided with each device.
Available external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
Antenna connection
Connect the TV to a wall antenna socket with an RF
cable (75 Ω).
ANTENNA/
CABLE IN
NOTE
yy The external device connection may differ from
the model.
yy Connect external devices to the TV regardless of
the order of the TV port.
yy If you record a TV programme on a DVD recorder
or VCR, make sure to connect the TV signal input
cable to the TV through a DVD recorder or VCR.
For more information of recording, refer to the
manual provided with the connected device.
yy Refer to the external equipment’s manual for
operating instructions.
yy If you connect a gaming device to the TV, use the
cable supplied with the gaming device.
yy In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast or
brightness. If noise is present, change the PC
output to another resolution, change the refresh
rate to another rate or adjust the brightness and
contrast on the PICTURE menu until the picture is
clear.
yy In PC mode, some resolution settings may not
work properly depending on the graphics card.
NOTE
yy Use a signal splitter to use more than 2 TVs.
yy If the image quality is poor, install a signal
amplifier properly to improve the image quality.
yy If the image quality is poor with an antenna
connected, try to realign the antenna in the correct
direction.
yy An antenna cable and converter are not supplied.
yy Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
ENGLISH
ENG
MAKING CONNECTIONS
19
20
MAKING CONNECTIONS
ENGLISH
ENG
HDMI connection
Component connection
Transmits the digital video and audio signals from an
external device to the TV. Connect the external device
and the TV with the HDMI cable as shown.
Transmits analog video and audio signals from an
external device to the TV. Connect the external device
and the TV with a component cable as shown.
IN
DVD/ Blu-Ray / HD Cable
Box / HD STB / PC
RED
WHITE
RED
BLUE
GREEN
(*Not Provided)
(*Not Provided)
L
VIDEO
RED
WHITE
NOTE
yy It is recommended to use the TV with the HDMI
connection for the best image quality.
yy Use the latest High Speed HDMI™ Cable with
CEC (Customer Electronics Control) function.
yy High Speed HDMI™ Cables are tested to carry
an HD signal up to 1080p and higher.
yy Supported HDMI Audio format : Dolby
Digital, DTS, PCM (Up to 192 kHz,
32k/44.1k/48k/88k/96k/176k/192k)(Only LA61**,
LN565*)
yy Supported HDMI Audio format : Dolby Digital,
PCM (Up to 192 kHz, 32k/44.1k/48k/88k/96k/17
6k/192k) *DTS Not Supported. (Only LN54**)
yy If you use DVI to HDMI cable for PC, you have
to use external speaker for PC audio sound.
RED
BLUE
GREEN
HDMI
R
AUDIO
DVD/ Blu-Ray / HD Cable Box
NOTE
yy If cables are not installed correctly, it could cause
this image to display in black and white or with
distorted colours.
MAKING CONNECTIONS
21
Transmits analog video and audio signals from an
external device to the TV. Connect the external device
and the TV with the composite cable as shown.
Connect a USB storage device such as a USB flash
memory, external hard drive, or a USB memory card
reader to the TV and access the My media menu to use
various multimedia files.
USB IN
USB connection
USB
(*Not Provided)
RED
WHITE
YELLOW
(*Not Provided)
L (MONO) AUDIO R
DVD/ Blu-Ray / HD Cable Box / VCR
RED
WHITE
YELLOW
VIDEO
ENGLISH
ENG
Composite connection
22
MAKING CONNECTIONS
Audio Connection
Transmits the headphone signal from the TV to
an external device. Connect the external device
and the TV with the headphone as shown.
(Only LA61**)
You may use an optional external audio system instead
of the built-in speaker.
Digital optical audio connection
H/P OUT
ENGLISH
ENG
Headphone connection
Transmits a digital audio signal from the TV to an
external device. Connect the external device and the TV
with the optical audio cable as shown.
OPTICAL
DIGITAL
AUDIO OUT
(*Not Provided)
NOTE
yyAUDIO menu items are disabled when connecting
a headphone.
yyWhen changing AV MODE with a headphone
connected, the change is applied to video but not
to audio.
yyOptical Digital Audio Out is not available when
connecting a headphone. (Only LA61**)
yyHeadphone impedance: 16 Ω
yyMax audio output of headphone: 9 mW to 15 mW
yyHeadphone jack size: 0.35 cm
(*Not Provided)
OPTICAL AUDIO IN
Digital Audio System
NOTE
yyDo not look into the optical output port. Looking at
the laser beam may damage your vision.
yyAudio with ACP (Audio Copy Protection) function
may block digital audio output.
MAKING CONNECTIONS
IN 2 (MHL)
Mobile High-definition Link (MHL) is an interface for
transmitting digital audiovisual signals from mobile
phones to television sets.
MHL passive cable
(*Not Provided)
Mobile phone
NOTE
yyConnect the mobile phone to the HDMI IN 2
(MHL) port to view the phone screen on the TV.
yyThe MHL passive cable is needed to connect the
TV and a mobile phone.
yyThis only works for the MHL-enabled phone.
yySome applications can be operated by the
remote control.
yyRemove the MHL passive cable from the TV
when:
-- The MHL function is disabled.
-- Your mobile device is fully charged in standby
mode.
ENGLISH
ENG
MHL connection
23
24
REMOTE CONTROL
ENGLISH
ENG
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote
control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA)
matching the
and
ends to the label inside the compartment, and close
the battery cover.
To remove the batteries, perform the installation actions in reverse.
or
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
yyIn Analogue TV and some countries, some remote control buttons may not work.
Make sure to point the remote control toward the remote control sensor on the TV.
(Only LA61**)
(POWER)
TV/RAD
RATIO
INPUT
AV MODE
TV/
RAD
1
4
7
LIST
2
5
8
0
3
6
9
INPUT
Changes the input source.
AV MODE
Selects an AV mode.
Number buttons
Enters numbers.
LIST
Accesses the saved programme list.
Q.VIEW
Returns to the previously viewed programme.
FAV
Accesses your favourite programme list.
Q.MENU
OK
Scrolls through the saved programmes.
P
A
G
E
PAGE
GUIDE
EXIT
1
Accesses the main menus.
INFO
Views the information of the current programme and
screen.
Q.MENU
Accesses the Quick menus.
3D OPTION
Use this to view 3D video.
Navigation buttons
(up/down/left/right)
Scrolls through menus or options.
OK
Selects menus or options and confirms your input.
2
T.OPT
SUBTITLE
Returns to the previous level.
GUIDE
Shows programme guide.
EXIT
Clears on-screen displays and return to TV viewing.
1 Coloured buttons
TEXT
Moves to the previous or next screen.
SETTINGS
BACK
BACK
Mutes all sounds.
Adjusts the volume level.
P
3D OPTION
SETTINGS INFO
Resizes an image.
Used for viewing 3D video.
FAV
MUTE
Selects Radio, TV and DTV programme.
RATIO
MUTE
Q.VIEW
P
Turns the TV on or off.
These access special functions in some menus.
2 TELETEXT BUTTONS
(
: Red,
: Green,
: Yellow,
These buttons are used for teletext.
: Blue)
SUBTITLE
Recalls your preferred subtitle in digital mode.
Control buttons
(
)
Controls the MY MEDIA menus, or the SIMPLINK
compatible devices (USB,SIMPLINK).
Accesses the AV devices connected with the HDMI
cable through HDMI-CEC.
Opens the SIMPLINK menu.
REMOTE CONTROL
25
(Only LN54**, LN565*)
TV/
RAD
RATIO
SUBTITLE
INPUT
AV MODE
1
4
7
LIST
2
5
8
0
3
6
9
Q.VIEW
FAV
GUIDE
1
TEXT
INFO
SETTINGS
T.OPT
Q.MENU
EXIT
SLEEP
TV/RAD
SUBTITLE
Selects Radio, TV and DTV programme.
AV MODE
Selects an AV mode.
RATIO
INPUT
Recalls your preferred subtitle in digital mode.
Resizes an image.
Changes the input source.
Number buttons
Enters numbers.
LIST
Accesses the saved programme list.
Q.VIEW
Returns to the previously viewed programme.
FAV
Accesses your favourite programme list.
GUIDE
Shows programme guide.
MUTE
Mutes all sounds.
P
MUTE
Turns the TV on or off.
Adjusts the volume level.
P
Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
1 TELETEXT BUTTONS
These buttons are used for teletext.
INFO
Views the information of the current programme and
screen.
SETTINGS
Accesses the main menus.
Q.MENU
Accesses the Quick menus.
Navigation buttons (up/
down/left/right)
Scrolls through menus or options.
OK
BACK
Selects menus or options and confirms your input.
EXIT
Clears on-screen displays and return to TV viewing.
2
Returns to the previous level.
Accesses the AV devices connected with the
HDMI cable through HDMI-CEC.
Opens the SIMPLINK menu.
SLEEP
Sets the sleep timer.
Control buttons
(
)
Controls the MY MEDIA menus, or the SIMPLINK
compatible devices (USB,SIMPLINK).
2 Coloured buttons
These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
ENGLISH
ENG
(POWER)
26
USING THE USER GUIDE
ENGLISH
ENG
USING THE USER GUIDE
User Guide allows you to more easily access the detailed TV information.
Press SETTINGS to access the main menus.
Press the RED button to access the Customer
Support menus.
Press the Navigation buttons to scroll to User Guide
and press OK.
1
2
3
User Guide
1
PROGRAMME Setting
PICTURE, SOUND Setting
OPTION
OPTION > To set language
SETTINGS  OPTION  Language
You can select the language of the menu displayed on the screen and the digital
sound broadcasting.
 Menu Language : Selects a language for the display text.
 Audio Language [In Digital mode Only] : Select the desired language when
watching digital broadcasting containg several voice languages.
 Subtitle Language [In Digital mode Only] : Use the Subtitle function when two
or more subtitle languages are broadcast.
✎ If subtitle data in a selected language is not broadcast, the default
language subtitle will be displayed.
Advanced Function
PICTURE
AUDIO
SETUP
TIME
LOCK
OPTION
INPUT
MY MEDIA
Information
Zoom In
Close
SETTINGS  OPTION  Language
You can select the language of the menu displayed on the screen and the digital
sound broadcasting.
 Menu Language : Selects a language for the display text.
 Audio Language [In Digital mode Only] : elect the desired language when
watching digital broadcasting containg several voice languages.
 Subtitle Language [In Digital mode Only] : Use the Subtitle function when two
or more subtitle languages are broadcast.
✎ If subtitle data in a selected language is not broadcast, the default
language subtitle will be displayed.
Press OK() to set picture settings.
Customer Support
2
Exit
Software Update
Picture Test
Sound Test
2
Signal Test
Zoom Out
Close
Product/Service Info.
User Guide
Close
User Guide
3
2
To use input device
To set time options
PROGRAMME Setting
To set TV lock options
PICTURE, SOUND Setting
OPTION
To set language
To set country
Advanced Function
To set subtitle
Information
1
To set other options
1
Allows to select the category you want.
2
Allows to select the item you want.
You can use ꕌ/ꕍ to move between pages.
3
Allows to browse the description of the function
you want from the index.
1
Shows the description of the selected menu.
You can use ꕌ/ꕍ to move between pages.
2
Zooms in or out the screen.
MAINTENANCE / TROUBLESHOOTING
ENGLISH
ENG
MAINTENANCE
27
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
y y Make sure to turn the power off and disconnect the power cord and all other cables first.
y y When the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to
prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
y y To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
y y To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then
wipe immediately with a dry cloth.
CAUTION
y y Avoid touching the screen at all times, as this may result in damage to the screen.
y y Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in scratches
and image distortions.
y y Do not use any chemicals as this may damage the product.
y y Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Problem
Solution
Cannot control the
TV with the remote
control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
to ,
to
yy Check if the batteries are still working and properly installed (
No image display and
no sound is produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Auto sleep or Off time feature is activated in the Time settings.
yy If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes
of inactivity.
When connecting
to the PC (HDMI),
‘No signal’ or ‘Invalid
Format’ is displayed.
yy Turn the TV off/on using the remote control.
yy Reconnect the HDMI cable.
yy Restart the PC with the TV on.
).
28
SPECIFICATIONS
ENGLISH
ENG
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
MODELS
32LN54**
37LN54**
39LN54**
32LN5400-TA
32LN541B-TB
32LN5420-TC
32LN542B-TC
32LN5430-TD
32LN543B-TD
32LN5440-TJ
32LN544B-TJ
32LN542Y-TC
32LN542Z-TC
32LN543Y-TD
32LN543Z-TD
32LN544Y-TJ
32LN544Z-TJ
32LN541B-TC
32LN541Y-TC
32LN540B-TA
32LN5460-TA
32LN546B-TA
32LN5460-TM
32LN546B-TM
32LN546Y-TM
32LN546Z-TM
37LN5400-TA
37LN541B-TB
37LN5420-TC
37LN542B-TC
37LN5430-TD
37LN543B-TD
37LN5440-TJ
37LN544B-TJ
37LN542Y-TC
37LN542Z-TC
37LN543Y-TD
37LN543Z-TD
37LN544Y-TJ
37LN544Z-TJ
37LN541B-TC
37LN541Y-TC
37LN540B-TA
37LN5460-TA
37LN546B-TA
37LN5460-TM
37LN546B-TM
37LN546Y-TM
37LN546Z-TM
39LN5400-TA
39LN541B-TB
39LN5420-TC
39LN542B-TC
39LN5430-TD
39LN543B-TD
39LN5440-TJ
39LN544B-TJ
39LN542Y-TC
39LN542Z-TC
39LN543Y-TD
39LN543Z-TD
39LN544Y-TJ
39LN544Z-TJ
39LN541B-TC
39LN541Y-TC
39LN540B-TA
39LN5460-TA
39LN546B-TA
39LN5460-TM
39LN546B-TM
39LN546Y-TM
39LN546Z-TM
Dimensions
(W x H x D)
With stand (mm)
738.0 x 497.0 x 207.0
849.0 x 561.0 x 236.0
894.0 x 587.0 x 236.0
Without stand(mm)
738.0 x 449.0 x 79.0
849.0 x 512.0 x 79.0
894.0 x 537.0 x 79.0
Weight
With stand (kg)
7.0
9.1
9.7
Without stand (kg)
6.4
8.0
8.6
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power requirement
SPECIFICATIONS
47LN54**
50LN54**
42LN5400-TA
42LN541B-TB
42LN5420-TC
42LN542B-TC
42LN5430-TD
42LN543B-TD
42LN5440-TJ
42LN544B-TJ
42LN542Y-TC
42LN542Z-TC
42LN543Y-TD
42LN543Z-TD
42LN544Y-TJ
42LN544Z-TJ
42LN541B-TC
42LN541Y-TC
42LN540B-TA
42LN5460-TA
42LN546B-TA
42LN5460-TM
42LN546B-TM
42LN546Y-TM
42LN546Z-TM
47LN5400-TA
47LN541B-TB
47LN5420-TC
47LN542B-TC
47LN5430-TD
47LN543B-TD
47LN5440-TJ
47LN544B-TJ
47LN542Y-TC
47LN542Z-TC
47LN543Y-TD
47LN543Z-TD
47LN544Y-TJ
47LN544Z-TJ
47LN541B-TC
47LN541Y-TC
47LN540B-TA
47LN5460-TA
47LN546B-TA
47LN5460-TM
47LN546B-TM
47LN546Y-TM
47LN546Z-TM
50LN5400-TA
50LN541B-TB
50LN5420-TC
50LN542B-TC
50LN5430-TD
50LN543B-TD
50LN5440-TJ
50LN544B-TJ
50LN542Y-TC
50LN542Z-TC
50LN543Y-TD
50LN543Z-TD
50LN544Y-TJ
50LN544Z-TJ
50LN541B-TC
50LN541Y-TC
50LN540B-TA
50LN5460-TA
50LN546B-TA
50LN5460-TM
50LN546B-TM
50LN546Y-TM
50LN546Z-TM
Dimensions
(W x H x D)
With stand (mm)
968.0 x 629.0 x 236.0
1080.0 x 694.0 x 264.0
1136.0 x 727.0 x 264.0
Without stand(mm)
968.0 x 579.0 x 79.0
1080.0 x 642.0 x 80.5
1136.0 x 673.0 x 82.1
Weight
With stand (kg)
10.7
14.5
15.6
Without stand (kg)
9.6
13.1
14.2
Power requirement
MODELS
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
55LN54**
60LN54**
32LN565*
55LN5400-TA
55LN541B-TB
55LN5420-TC
55LN542B-TC
55LN5430-TD
55LN543B-TD
55LN5440-TJ
55LN544B-TJ
55LN542Y-TC
55LN542Z-TC
55LN543Y-TD
55LN543Z-TD
55LN544Y-TJ
55LN544Z-TJ
55LN541B-TC
55LN541Y-TC
55LN540B-TA
55LN5460-TA
55LN546B-TA
55LN5460-TM
55LN546B-TM
55LN546Y-TM
55LN546Z-TM
60LN5400-TA
60LN541B-TB
60LN5420-TC
60LN542B-TC
60LN5430-TD
60LN543B-TD
60LN5440-TJ
60LN544B-TJ
60LN542Y-TC
60LN542Z-TC
60LN543Y-TD
60LN543Z-TD
60LN544Y-TJ
60LN544Z-TJ
60LN541B-TC
60LN541Y-TC
60LN540B-TA
60LN5460-TA
60LN546B-TA
60LN5460-TM
60LN546B-TM
60LN546Y-TM
60LN546Z-TM
32LN5650-TA
Dimensions
(W x H x D)
With stand (mm)
1250.0 x 790.0 x 297.0
1359.0 x 852.0 x 297.0
743.0 x 499.0 x 206.0
Without stand(mm)
1250.0 x 737.0 x 79.1
1359.0 x 799.0 x 67.2
743.0 x 451.0 x 96.0
Weight
With stand (kg)
21.2
26.3
8.8
Without stand (kg)
19.1
24.2
8.3
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power requirement
ENGLISH
ENG
MODELS
42LN54**
29
30
SPECIFICATIONS
ENGLISH
ENG
MODELS
32LA61**
42LA61**
50LA61**
32LA6130-TB
32LA6150-TC
32LA615B-TC
32LA613B-TB
32LA615Y-TC
32LA613Y-TB
32LA6160-TD
32LA616B-TD
32LA6170-TE
32LA617B-TE
32LA616Y-TD
42LA6130-TB
42LA6150-TC
42LA615B-TC
42LA613B-TB
42LA615Y-TC
42LA613Y-TB
42LA6160-TD
42LA616B-TD
42LA6170-TE
42LA617B-TE
42LA616Y-TD
50LA6130-TB
50LA6150-TC
50LA615B-TC
50LA613B-TB
50LA615Y-TC
50LA613Y-TB
50LA6160-TD
50LA616B-TD
50LA6170-TE
50LA617B-TE
50LA616Y-TD
Dimensions
(W x H x D)
With stand (mm)
733.0 x 499.0 x 242.0
964.0 x 631.0 x 294.0
1131.0 x 725.0 x 327.0
Without stand(mm)
733.0 x 444.0 x 78.0
964.0 x 573.0 x 78.0
1131.0 x 667.0 x 80.9
Weight
With stand (kg)
7.6
11.8
17.0
Without stand (kg)
6.4
10.0
14.5
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power requirement
SPECIFICATIONS
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Digital TV
New Zealand,
Singapore
Television System
Programme Coverage
Australia
Television System
Programme Coverage
Indonesia, Israel,
Television System
Myanmar, Sri Lanka
Programme Coverage
Vietnam, Malaysia
Television System
Programme Coverage
Iran, Algeria,
Tunisia, Digital
model
Television System
Programme Coverage
Analogue model,
India, Thailand,
South Africa, --
Television System
Programme Coverage
External Antenna
Impedance
ENGLISH
ENG
Environment
condition
31
Analogue TV
DVB-T
PAL/SECAM-B/G/D/K, PAL-I
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
DVB-T
PAL B/B
VHF 06 to 12,
UHF 27 to 69
B/B : VHF/UHF 0 to 75, CATV : 2 to 44
DVB-T
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
DVB-T
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
VHF 6 to 12,
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
DVB-T
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
VHF 5 to 12,
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
-
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
-
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
75 Ω
75 Ω
32
SPECIFICATIONS
ENGLISH
ENG
Component port connecting information
HDMI-DTV supported mode
Resolution
Horizontal
Vertical
Frequency (kHz) Frequency (Hz)
720x480
31.469
31.5
59.94
60
720x576
31.25
50
1280x720
37.5
44.96
45
50
59.94
60
1920x1080
33.72
33.75
28.125
26.97
27
33.716
33.75
56.25
67.43
67.5
59.94
60
50
23.97
24
29.976
30.00
50
59.94
60
HDMI-PC supported mode
Resolution
Horizontal
Vertical
Frequency (kHz) Frequency (Hz)
640x350
31.468
70.09
720x400
31.469
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1152x864
54.348
60.053
1360x768
47.712
60.015
1280x1024
63.981
60.020
1920x1080
67.50
60.00
(Except for 32LN565*, 32/37LN541B, 32LN542B,
32/37LN543B, 32LN544B, 32LN542Z, 32LN543Z,
32LN544Z, 37LN541Y, 37LN543Y, 32LN540B,
32LN546B, 32LA613B, 32LA613Y, 32LA616B,
32LA617B, 32LA616Y )
Component ports on the TV
Video output ports on DVD
player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
SPECIFICATIONS
yy Video, which is input as below media contents is switched into the 3D screen automatically.
yy The method for 3D digital broadcast may differ depending on the signal environment. If video is not switched
automatically into 3D, manually convert the settings to view 3D images.
Input
Signal
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
50
60
50
59.94 / 60
50
60
24
30
23.98 / 24
50
60
50
50
30
DTV
720p
1080i
1280X720
1920X1080
37.5
45
75
89.9 / 90
28.125
33.7
27
33.7
53.95 / 54
56.3
67.5
37.5
28.125
USB
1080p
1920X1080
33.75
720p
HDMI
1080i
1080p
1280X720
1920X1080
1920X1080
Playable 3D video format
Side by Side(half),
Top and Bottom
Frame packing
Side by Side(half),
Top and Bottom
Side by Side(half),
Top and Bottom
Frame packing
Side by Side(half),
Top and Bottom
Side by Side, Top and Bottom
Side by Side, Top and Bottom,
MPO(Photo)
ENGLISH
ENG
3D supported mode (Only 3D model)
33
34
LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of
Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.
com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order
to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code,
locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274”
(Only LA61**)
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other
U.S. and worldwide patents issued & pending. DTS, the Symbol & DTS and the Symbol
together are registered trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product
includes software. © DTS, Inc. All Rights Reserved.
(Only LN565*)
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other
U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol
together are registered trademarks & DTS 2.0 Channel is a trademark of DTS, Inc. Product
includes software. © DTS, Inc. All Rights Reserved.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product,
please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for
download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is
valid for three (3) years from the date on which you purchased the product.
EXTERNAL CONTROL DEVICE SETUP
To obtain the external control device setup information, please visit www.lg.com
For any Suggestion, Opinion,
Complaints, Please Call
800 54 in UAE
0800 54 54 54 in South Africa
080 100 54 54 in Morocco
19960 in Egypt
Other countries, Please contact our
local dealer or log into
http://www.lg.com
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring any
service.
MODEL
SERIAL
(Only DTV)
Download PDF