LG | LM-D6960A | LG LM-D6960A Owner’s Manual

INTROPA_LM-D6960A_ENG_MFL38637153
MINI HOME THEATER
OWNER’S MANUAL
MODEL : LM-D6960
LM-D6960A
LMS-D6960V, LMS-D6960C
LMS-D6960S, LMS-D6960W
Please read this manual carefully before operating your set.
Retain it for future reference.
Designs and specifications are subject to change without
notice for improvement.
CD - R/R
R/RW
R
USB
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance
and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or
damaged wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous. Any of
these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with
an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets, and
the point where the cord exits the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
CAUTION: Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it
from over heating.
The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product
should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to.
CAUTION:
This Product employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference, should the unit
require maintenance, contact an authorized service locationsee service procedure.
Use of controls, adjustments or the performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
CAUTION: The apparatus shall not be exposed to water,
dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
CAUTION:
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED
2
Power Save Mode
You can set up the unit into an economic power save
mode.
In power-on status, press and hold POWER
( STANDBY/ON) button for about 3 seconds.
- Nothing is displayed on the display window when the
goes into the power save mode.
To cancel power save mode, press POWER ( STAND-
BY/ON), CLOCK, TIMER or DEMO.
Table of Contents
Before Use
Introduction
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2
3
3
4
5
DVD
(8 cm / 12 cm disc)
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Before Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-18
Audio CD
(8 cm / 12 cm disc)
Preparation
Operation
Operation with DVD and Video CD . . . . . . . . . . . . . . . . 18-21
Operation with Audio CD and MP3/WMA Disc . . . . . . . 21-22
Programmed Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Operation with JPEG Disc . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operation with DivX Disc . . . . . . . . . . . . . . . . . . . . . . . . . 24
Operation with RADIO . . . . . . . . . . . . . . . . . . . . . . . . . 25-26
Operation with TAPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Language Code List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Area Code List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Specifications
About Symbols
About the
symbol display
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbol is
applicable only to the disc represented by the symbol.
DVD DVD
VCD Video CDs
CD
Audio CDs
MP3 MP3 disc
WMA WMA disc
JPEG JPEG disc
DivX DivX disc
Video CD (VCD)
(8 cm / 12 cm disc)
In addition, this unit can play a DVD±R, DVD±RW,
SVCD, and CD-R or CD-RW that contains audio titles,
MP3, WMA, JPEG or DivX files.
Notes
– Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself,
some CD-R/RW (or DVD±R/RW) discs cannot be
played on the unit.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregularly shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
Notes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs
may be intentionally fixed by software manufacturers. As
this unit plays DVDs and Video CDs according to disc
content designed by the software manufacturer, some
playback features of the unit may not be available or
other functions may be added.
Refer also to the instructions supplied with the DVDs
and Video CDs. Some DVDs made for business purposes may not be played on the unit.
Regional code of the DVD player and DVDs
This DVD player is designed and manufactured
for playback of region “5” encoded DVD software. The region code on the labels of some
DVD discs indicates which type of player can play those
discs. This unit can play only DVD discs labeled “5” or
“ALL”. If you try to play any other discs, the message
“Check Regional Code” will appear on the TV screen.
Some DVD discs may not have a region code label even
though their playback is prohibited by area limits.
5
About the symbols for instructions
Indicates hazards likely to cause harm to the unit itself or
other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
ote on DTS-encoded CDs
When playing DTS-encoded CDs, excessive audio level
may be heard from the analog stereo output. To avoid
possible damage to the audio system, turn down the
volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy
DTS Digital SurroundTM playback, an external 5.1 channel DTS Digital SurroundTM decoder system must be
connected to the digital output of the unit.
3
INTRODUCTION
Playable Discs
Safety Precautions. . . . .
Table of Contents. . . . . .
Before Use . . . . . . . . . .
Front Panel/ Rear Panel.
Remote Control . . . . . . .
Front Panel/ Rear Panel
13
1
2
12
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Pr
14
3
4
Pb
S-VIDEO
OUT
OPTICAL
IN
Y
11
18
10
5
6
7
AUX IN
REAR
R (8 )
REAR
L (8 )
CENTER
(8 )
WOOFER
(3 )
FRONT
R (4 )
FRONT
L (4 )
17
9
8
15
16
1.
DISPLAY WINDOW
2.
3.
POWER ( STANDBY/ON) button
• PROGRAM/MEMORY (PROG./MEMO.) button
• STEREO/MONO (ST./MO.),
HIGH DUBBING (HI-DUBB.) button
• CD SYNCHRO RECORDING (CD SYNC.),
NORMAL DUBBING (NOR-DUBB.) button
• RECORD/RECORD PAUSE (zREC/[]) button
HEADPHONE SOCKET (PHONES): 3.5 mm
USB connector
• FUNCTION SELECT buttons
(TUNER, DVD/CD, TAPE, USB, AUX)
• SET/CD[], RDS (OPTIONAL) button
• XDSS plus button
• XTS Pro button
• Virtual E.X button
• EQ master button
• VOLUME knob
Z PUSH EJECT position (TAPE 1)
Z PUSH EJECT position (TAPE 2)
• PRESET (-/+) buttons
b) button
• TAPE REVERSE PLAY (b
B) button
• PLAY (B
• STOP (xSTOP) button
BB >), TAPE
• CD SKIP/SEARCH (. bb/B
BB >),
REWIND/ FAST FORWARD (. bb/B
TUNING (-/+) buttons
4.
5.
6.
7.
8.
9.
4
10. • MIC VOLUME KNOB (MIC VOL.)
• MIC JACKS (MIC1, MIC2): 6.3 mm : OPTIONAL
11. • DISC SKIP (D.SKIP) button
• CLOCK button
• TIMER button
• PLAY MODE, DEMO button
12. • OPEN/CLOSE (ZOP./CL.) button
• DISC SELECT buttons (DISC1, DISC2, DISC3)
13. DISC DOOR
14. • COMPONENT VIDEO OUT (PROGRESSIVE SCAN)
(Y Pb Pr) Connector
• VIDEO OUT Connector
15. • FM/AM ANTENNA Connector
• AUXILIARY INPUT (AUX IN) connector
16. POWER CORD
17. SPEAKER Connectors
18. • S-VIDEO OUT Connector
• OPTICAL IN Connector
Remote Control
1
TUNER/BAND
DVD
AUX
22
USB
1.
2.
3.
4.
2
SLEEP
21
DIMMER
3
20
4
5.
6.
1 - TAPE - 2
5
SETUP
DISPLAY
PRESET +
19
TUN. -
TUN. +
6
7.
8.
SELECT
/ENTER
7
8
MENU
9
STOP
PRESET PAUSE/STEP PLAY
PROG./MEMO.
SCAN
REPEAT
SKIP
10
TITLE
18
17
REPEAT A-B MARKER
SEARCH
EQ master
XTS Pro
XDSS plus VIRTUAL E.X
SOUND
AUDIO
RETURN
ZOOM
S-TITLE
CLEAR
RDS
PTY
MUTE
15
12.
13.
14.
15.
16.
14
17.
18.
16
11
12
ECHO VOL.
MIC VOL.
9.
10.
11.
13
19.
20.
21.
22.
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
• Distance: About 23 ft (7 m) from the front of the
remote sensor
• Angle: About 30° in each direction of the front of the
remote sensor
POWER button
FUNCTION SELECT buttons
(TUNER/BAND, DVD, AUX, USB)
NUMERIC buttons (0-9)
TAPE FUNCTION buttons
- REVERSE PLAY (F)
- PLAY (G)
- REWIND/ FAST FORWARD PLAY (FF/GG)
- TAPE 1-2 SELECT buttons (1-TAPE-2)
- RECORD/ RECORD PAUSE (z/[])
- TAPE STOP (x)
SET UP button
INTRODUCTION
D.SKIP
POWER
• ARROW buttons ( /
/ / )
(For use in highlighting a selection on a GUI
menu screen, TITLE and MENU screen.)
• PRESET (-/+) buttons ( / )
• TUN. (-/+) buttons ( / )
SELECT/ENTER button
MENU button
(Use the MENU button to display the menu screen
included on DVD video discs.)
STOP (x), PAUSE([])/ STEP, PLAY (G) buttons
PROG./MEMO., REPEAT, REPEAT A-B buttons
EQ master, XTS Pro, SOUND, AUDIO, SUBTITLE
(S-TITLE), CLEAR buttons
ECHO VOL. ( / ) buttons
MIC VOL. ( / ) buttons
RDS, PTY buttons (OPTIONAL)
XDSS plus, VIRTUAL E.X,RETURN, ZOOM buttons
SCAN (FF/GG)/ SCAN (-/+)/ SKIP (-/+)/ SKIP
(./>), MARKER, SEARCH, MUTE buttons
VOLUME -/+ buttons
TITLE button
(Use the TITLE button to display the title screen
included on DVD video discs.)
DISPLAY button
DIMMER button
SLEEP button
DISC SKIP (D.SKIP) button
Remote control battery installation
Detach the battery cover on
the rear of the remote control, and insert two R03 (size
AAA) batteries with
and
aligned correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
5
Connections
Connecting to a TV
• Make one of the following connections, depending on
the capabilities of your existing equipment.
ips
• Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the unit. Use one of the connections described below.
• Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the
best connections.
Caution
– Make sure the unit is connected directly to the TV.
Select the correct AV input on your TV.
– Do not connect your unit to TV via your VCR. The
DVD image could be distorted by the copy protection
system.
Progressive Scan (ColorStream® pro) connection
• If your television is a high-definition or “digital ready”
television, you may take advantage of this unit’s
progressive scan output for higher video resolution.
• If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try
Progressive Scan on the unit.
Connect the COMPONENT VIDEO OUT (PROGRESSIVE SCAN) (Y Pb Pr) jacks from the unit to the corresponding in jacks on the TV using an optional Y Pb Pr
cable (C).
otes
– Set the Progressive to “On” in the Setup menu for
progressive signal, see page 15.
Video connection
Connect the VIDEO OUT jack from the unit to the
VIDEO IN jack on the TV using the video cable supplied
(V).
S-Video connection
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Connect the S-VIDEO OUT jack on the unit to the SVIDEO IN jack on the TV using the S-Video cable (S).
Pr
Pb
S-VIDEO
OUT
OPTICAL
IN
Y
Component Video (Color Stream®) connection
WOOFER
PRE-OUT
Connect the COMPONENT VIDEO OUT (PROGRESSIVE SCAN) (Y Pb Pr) jacks from the unit to the corresponding in jacks on the TV using an Y Pb Pr cable (C).
C
H
A
N
N
E
L
REAR
R (8 )
REAR
L (8 )
CENTER
(8 )
WOOFER
(3 )
FRONT
R (4 )
FRONT
L (4 )
MIC ANT.
AUX IN
C
COMPONENT VIDEO /
PROGRESSIVE SCAN INPUT
Pr
S
V
Y
VIDEO
IN
Pb
L
Rear of TV
6
S-VIDEO
IN
Connecting to Antenna
Connecting to Auxiliary Equipment
Connect the supplied FM/AM antennas for listening to
the radio.
- Connect the AM loop antenna to the AM antenna
connector.
- Connect the FM wire antenna to the FM antenna
connector.
You can use VCR or other unit connected to the AUX
connector.
This unit receives the analog signal from auxiliary
equipment.
AUX IN
REAR
R (8 )
REAR
L (8 )
CENTER
(8 )
WOOFER
(3 )
FRONT
R (4 )
FRONT
L (4 )
AM(MW) loop
antenna (aerial)
(Supplied)
VCR (or Auxiliary
Device, etc)
IN
To AUDIO IN
OUT
VIDEO
AUDIO (L)
AUDIO (R)
For AM(MW) reception, connect the
loop antenna (aerial) to the terminal
marked AM
To AUDIO OUT
EURO AV
COMPONENT VIDEO OUT
Pr
TO TV
S-VIDEO
OUT
OPTICAL
IN
Y
FM wire
antenna
(supplied)
AUX IN
REAR
R (8 )
REAR
L (8 )
CENTER
(8 )
WOOFER
(3 )
1
the AUX button on the front panel or the
2 Press
remote control until the “AUX” indicator is
Connect a VCR or auxiliary device, etc to the
AUX connector.
Pb
FRONT
R (4 )
FRONT
L (4 )
displayed in the display window.
otes
• To prevent noise pickup, keep the AM loop antenna
away from the unit and other component.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as
horizontal as possible.
7
PREPARATION
Connections
Connections
Connecting to Optional Equipment
Connecting USB
You can use an optical output of a Digital Device to the
OPTICAL IN connector.
This unit receives the optical digital signal from optional
equipment.
OPTICAL
OUT
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Pr
Pb
S-VIDEO
OUT
Y
OPTICAL
IN
USB Memory,
MP3 Player (or
Memory Card
Reader, etc.)
DVD Player
(or Digital Device,
etc)
WOOFER
1
the AUX button on the front panel or the
2 Press
remote control until the “OPT IN” indicator is
Connect an optical output of DVD Player (or
Digital Device etc) to the OPTICAL IN connector.
1
displayed in the display window.
USB function by pressing the USB
2 Select
button on the front panel or the remote control.
Connect the USB port of USB memory (or MP3
player, etc) to the USB connector on the front
panel.
The “USB” is displayed in the display window.
To Remove the USB from the unit
1. Choose a different function mode or press the STOP
(x) twice in a row.
2. Remove the USB from the unit.
otes
• Don’t extract the USB device in operating.
• Music files (MP3/WMA), image files (JPEG) and
Video files can be played.
• This unit can not use USB HUB.
• Recommended Memory Card
Compact Flash Card (CFC), Micro Drive (MD), Smart
Media Card (SMC), Memory Stick (MS), Secure Digital
Card (SD), Multi Media Card (MMC), Memory Stick Pro
(MS-Pro)
- Compatable with : FAT16,32
- Only use the memory cards recommended.
• Devices which require additional program installation
when you have connected the unit to a computer are
not supported.
• In case of a USB HDD, make sure to connect an auxiliary power cord to the USB HDD for porper operation.
A primary partition of drive is supported up to four. If
there is an extention partition it is not supported.
• If the drive of USB device is two or more, a drive
folder is displayed on the screen. If you want to
move to the previous menu after you select a folder,
press RETURN.
• Digital camera and mobile phone are not supported.
8
Connections
Speaker System Connection
PREPARATION
Connect the speakers using the supplied speaker cables by matching the colors of the terminals and those of the
cords. To obtain the best possible surround sound, adjust the speaker parameters (distance, level, etc.).
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Pr
Pb
S-VIDEO
OUT
OPTICAL
IN
Y
AUX IN
REAR
R (8 )
REAR
L (8 )
CENTER
(8 )
WOOFER
(3 )
FRONT
R (4 )
FRONT
L (4 )
otes
• Be sure to match the speaker cables to the appropriate terminal on the components: + to + and – to –. If the
cables are reversed, the sound will be distorted and will lack base.
• If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on
the speakers.
• Connect the Front Left/Right speaker correctly. If it is reversed, the sound may be distorted.
9
Before Operation
Volume Adjustment
XDSS (Extreme Dynamic Sound System)
• Turn VOLUME knob clockwise to increase the sound
level, or counterclockwise to decrease it.
• Press VOLUME + to increase the sound level, or use
VOLUME - to decrease it on the remote control.
You can improve the sound quality during playback.
Press XDSS plus repeatedly on the remote contol.
DVD/VCD/DivX/CD
NORMAL y XDSS ON
MP3/WMA NORMAL → XDSS ON → MP3 - OPT ON
MUTE
Press MUTE to turn off the sound, press again to
restore.
“ ” indicator flashes in the display window.
Headphone Jack
XTS/XTS pro
Each time you press XTS pro the setting changes in
the following order.
XTS ON → NORMAL → XTS-P ON → XTS ON ...
Connect a stereo headphone plug ( 3.5mm) into the
headphone jack.
The speakers are automatically disabled when you plug
in headphones (not supplied).
EQUALIZER Effect
You can choose 7 fixed sound impressions and adjust
the BASS, MIDDLE and TREBLE.
- You can select a desired sound mode by using EQ
master button on the front panel or the remote
control.
When you want to change a sound mode press the
EQ master button repeatedly within 3 seconds.
Each time you press the button the setting changes in
the display window as shown below.
• XTS-P ON
The unique sound quality of the LG Technology creates the optimum sound for you to play the perfect
playback of the original sound and to feel the living
sound source.
• XTS ON
When playing the movie with the weak bass sound
relatively to the general music, it enforces the sense
of sound at woofer for you to satisfy with.
In the mode of 2 CH BYPASS, It creates the high display effect by playing the sound source via the rear
speakers same as the front speakers.
otes
• The XTS mode is temporarily disabled when changing from 2.1
CH to 5.1 CH and it is enabled when changing it to 2.1 CH.
NORMAL → USER EQ → POP → CLASSIC
↑
• This function does not work when the microphone is in use.
JAZZ
VIRTUAL sound
←
DRAMA
←
ROCK
- You can set the BASS, MIDDLE and TREBLE on the
USER EQ mode.
1. Select the USER EQ mode by using EQ master
button.
“USER EQ” will be displayed in the display window.
2. Press the SET/CD[[ button on the front panel when
“USER EQ” is displayed in the display window.
“BASS 0” will be displayed in the display window.
3. Select the BASS, MIDDLE or TREBLE you want by
pressing the PRESET (-/+) buttons on the front
panel.
4. Press the TUNING (-/+) buttons on the front panel
to set the sound level you want. (MIN, -4 ~ +4,
MAX steps)
5. Repeat the 3-4 steps as above.
6. When the sound level is completed, press the the
SET/CD[[ button on the front panel.
DEMO
Press DEMO in power off state to demonstrate the
function in the display window.
To cancel, press POWER ( STANDBY/ON) or DEMO
again.
10
Press VIRTUAL E.X the setting VIRTUAL sound.
Source
2.1 ch.
5.1 ch
Display
VIRTUAL
VIRTUAL
Effect
3D STEREO
Multichannel sound
• 3D STEREO
Realtime 3D positioned sound rendering technology
with stereo sources, optimized for stereo speakers.
Listeners may experience amazing virtual surround
effects with their own multimedia players.
• Multichannel sound
The multichannel sound makes a 5.1 ch feel 10.1 ch
sound therefore this mode provides a emotion which
you are involved with sound and you can feel
detailed sound.
DIMMER
This function dims the LED (Light-emitting diode) of
front panel by half in power-on status.
Press DIMMER once. The LED (Light-emitting diode) of
front panel is turned off and the display window will be
darken by half. To cancel, press the button again.
Setting the Clock
Using Microphone
1
You can sing to a music source by connecting a
microphone to the unit.
Press CLOCK.
(If the clock requires setting, press and hold CLOCK
for more than 2 seconds.)
- The hours display begins to blink.
2 pressing . bb/BBB > on the front panel.
Select a 24 hour cycle or 12 hour cycle by
(12HR)
or
(24HR)
1 “ ” will be shown in the display window.
Play the music you want.
2
Sing along with the accompaniment.
the microphone volume by turning MIC
3 Adjust
VOLUME KNOB. (MIN,1 - 14, MAX steps)
Connect your microphone to the MIC socket.
3 cycle.
BB > on the front panel to set
Use . bb/B
4 the correct hours.
Press SET/CD[[.
5
BB > on the front panel to set
. Use . bb/B
6 the correct minutes.
Press SET/CD[[ and the correct time is shown in
7 the display window.
otes
• When not using the microphone, set the MIC volume
knob to minimum or turn off the MIC and remove the
microphone from the MIC socket.
• If the microphone is set too near the speaker, a
howling sound may be produced. In this case, move
the microphone away from the speaker or decrease
the sound level by using the MIC volume control.
• If sound through the microphone is extremely loud, it
may be distorted. In this case, turn the MIC volume
control toward minimum.
Sleep Timer Function
To Adjust ECHO Volume
Press SET/CD[[ to confirm the selected hour
When the sleep timer is set, the unit automatically turns
off after the specified time has elapsed.
1
To specify the time delay before the power is
turned off, press SLEEP.
In the display window you can see SLEEP 180 for
about 5 seconds. This means that the system turns
off automatically after 180 minutes.
You can give an echo effect to the sound from the
microphones.
Press the ECHO VOL. ( / ) on the remote control to
increase the echo volume or decrease it. (MIN,1 - 14,
MAX steps)
time you press SLEEP the setting changes
2 Each
in the following order.
3
SLEEP 180 →150 → 120 →90→80→70 → 60→ 50 →
40 → 30 → 20 →10 → OFF (No display) →SLEEP 180...
To check the remaining time until the power is
turned off.
While the sleep function is active press SLEEP
briefly. The time remaining until the unit turns off is
displayed for about 5 seconds.
ote
If you press SLEEP while the sleep time is displayed,
the SLEEP time is reset.
To cancel Sleep Timer setting
If you wish to stop the function, press the SLEEP button
repeatedly until “SLEEP 10 ” appears, and then press
SLEEP once again after “SLEEP 10 ” shows on the
display.
11
PREPARATION
Before Operation
Before Operation
Timer Function
With the TIMER function you can have the radio reception, CD play, USB play and TAPE play turned on and
off at the time desired.
1
Press CLOCK to check the current time.
For your reference
If you don’t set clock, timer function doesn’t work.
tUSBtTAPE” flash in the
2 “TUNERtDVD/CD
display window in turn.
Press TIMER to enter the timer setting mode.
For your reference
If you want to correct the previous memorized TIMER
setting, press and hold the TIMER button more than 2
seconds.
- The previous memorized timer setting for on Time and
“ ” indicator appears in the display window.
3 es.
Press SET/CD[[ when the desired function flash-
4
1. a. When you select TUNER function, ‘PLAY’
and ‘REC’ indicator flash in the display
window alternately for about 3 seconds.
‘PLAY’ indicator : TUNER play only
‘REC’ indicator : TUNER play and recording
b.Press SET/CD[[ when the desired function
flashes.
c.Select the previous memorized preset
BB > on the
number by pressing . bb/B
front panel and press SET.
‘ON TIME’ indicator appears for about 0.5
seconds in the display window and then
disappears.
2. When you select DVD/CD, USB or TAPE
function,
‘ON TIME’ indicator appears for about 0.5
seconds in the display window and then
disappears.
5 . bb/BBB > on the front panel.
Set the hour to switch on by pressing
6 time.
Press SET/CD[[ to confirm the turn on hour
12
7
Set the minute to switch on by pressing
. bb/B
BB > on the front panel.
8 time.
‘OFF TIME’ indicator appears for about 0.5
Press SET/CD[[ to confirm the turn on minutes
seconds in the display window and then
disappears.
9 . bb/BBB > on the front panel.
10 Press SET/CD[[.
the minute to switch off by pressing .
11 Set
bb/B
BB > on the front panel.
12 Press SET/CD[[.
the volume level by pressing
13 Adjust
. bb/B
BB > on the front panel.
SET/CD[[.
14 “Press
” appears in the display window and the timer
Set the hour to switch off by pressing
setting has been completed.
15
Turn the system off.
The selected timer functions are automatically
switched on and off at the preset times.
To cancel or check the timer
Each time the TIMER button is pressed you can select
the timer set or cancel. You can also check the timer
setting status.
To activate or check the timer, press the TIMER
button repeatedly so that “ ” appears in the display window.
To cancel the TIMER, press the TIMER button
repeatedly so that “ ” disappears from the display
window.
otes
• If you insert the DVD,VCD or DivX except audio
CD/MP3/WMA on the unit, the timer function will be
operated to the TUNER.
• This is not supported in the multi card reader.
Before Operation
Allows you to enjoy 5.1(or 6) discrete channels of high quality digital audio from DTS program sources such as discs, DVD and
compact discs, etc.bearing the trademark. DTS Digital Surround
delivers up to 6 channels of deemed audibly in distinguishable
from the master (which means identical to the original masters)
and results in exceptional clarity throughout a true 360 degree
sound field. “Manufactured under license from Digital Theater
Systems, Inc. US Pat. No’. 5,451,942; 5,956,674; 5,974,380;
5,978,762;6 and world-wide patents issued and pending. “DTS”
and “DTS Digital Surround” are registered trademarks of Digital
Theater Systems, Inc. Copyright 1996, 2003 Digital Theater
Systems, Inc. All rights Reserved.”
Sound Mode
DVD
VCD
You can enjoy surround sound simply by selecting one
of the pre-programmed sound fields according to the
program you want to listen to.
When DVD is inserted
You can change the Digital Audio Output mode by
pressing the AUDIO button on the remote control during
playback. Although the DVD contents differ from disc to
disc, the following explains the basic operation when
this feature is used.
a) After you select 2 channel (For example
or
) by pressing AUDIO button, press
SOUND button repeatedly.
2 ENG
D
2 CH
3 ENG
D
2 CH
TV screen
Bypass
STAGE
MATRIX
The Dolby Digital surround format lets you enjoy up to 5.1 channels of digital surround sound from a Dolby Digital program
source. If you play DVDs with “
” mark, you can enjoy even
better sound quality, greater spatial accuracy, and improved
dynamic range. Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and double-D symbol are
trademarks of Dolby Laboratories. Confidential Unpublished works.
Copyright 1992-1997 Dolby Laboratories. All rights reserved.
Use this mode when playing movie or Dolby Digital 2 channel
which carries the “
” mark. This mode provides the effect of
being in a movie theatre or live concert house-an effect with an
intensity which can only be obtained through DOLBY PRO LOGIC
SURROUND. The effect of the front/back/left/right movement of
the sound image, as well as the sense of fixed position in the
sound image, is much clearer and more dynamic than before.
II
Dolby Pro Logic II creates five full-bandwidth output channels
from two-channel sources. This is done using an advanced, highpurity matrix surround decoder that extracts the spatial properties
of the original recording without adding any new sounds or tonal
colorations.
MOVIE mode:
The Movie mode is for use with stereo television shows and all
programs encoded in Dolby Surround. The result is enhanced
soundfield directionality that approaches the quality of discrete
5.1-channel sound.
MUSIC mode:
The Music mode is for use with any stereo music recordings.
MATRIX mode:
The Matrix mode is the same as the Music mode except that
the directional enhancement logic is turned off. It may be used
to enhance mono signals by making them seem “larger.” The
Matrix mode may also find use in auto systems, where the fluctuations from poor FM stereo reception can otherwise cause
disturbing surround signals from a logic decoder. The ultimate
“cure” for poor FM stereo reception may be simply to force the
audio to mono.
BYPASS
Outputs the sound from the front left and right speakers and
subwoofer.
CD
MOVIE
MUSIC
b) After you select 5.1 channel (For example
4 ENG
DTS
5.1 CH
1 ENG
D
5.1 CH
or
) by pressing AUDIO button, press SOUND button.
- “ ” indicator will be displayed on the TV screen.
- “BYPASS” indicator will be only displayed in the display
window.
When Video CD is inserted
Each time you press SOUND button, the sound mode
of Video CD is changed in the display window in the
following order.
BYPASS → ON STAGE → STUDIO → CLUB → HALL →
THEATER 1 → CHURCH → PLII MOVIE → PLII MUSIC
→ PLII MTRX →BYPASS...
ote
After you select the “Bypass” of sound mode by
pressing SOUND button, press AUDIO button.
The Left, Right and Stereo of audio channel will be
displayed on the TV screen.
When CD is inserted
Each time you press SOUND button, the sound mode
of Audio CD is changed in the display window in the
following order.
BYPASS → ON STAGE → STUDIO → CLUB → HALL →
THEATER 1 → CHURCH → PLII MOVIE → PLII MUSIC
→ PLII MTRX →BYPASS...
For your reference
• Initial sound mode is BYPASS.
• You can identify the encoding format of program
software by looking at its packaging.
- Dolby Digital discs are labelled with the
logo.
- Dolby Surround encoded programs are labelled with
the
logo.
- DTS Digital Surround discs are marked with DTS.
otes
• When you play sound tracks with 96kHz sampling frequency,
the output signals will be converted to 48kHz (sampling frequency).
• When you use a microphone, you can’t enjoy 5.1 channel
output. Only 2 channel sound will out by the influence of the
microphone system.
13
PREPARATION
Mini Glossary for Audio Stream &
Surround mode
Before Operation
Caution:
Before using the remote control, press the DVD button to
select the device to be operated.
General Explanation
This manual gives basic instructions for operating the
unit. Some DVDs require specific operation or allow
only limited operation during playback.
When this occurs, the symbol
appears on the TV
screen, indicating that the operation is not permitted by
the unit or is not available on the disc.
On-Screen Display
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
On-screen display operation
1 Press DISPLAY during playback.
/
to select an item.
2 Press
The selected item will be highlighted.
or
to change the setting of an item.
3 Press
The number buttons can be also be used for setting numbers (e.g., title number). For some functions, press SELECT/ENTER to execute the setting.
Temporary Feedback Field Icons
Title
A-B
Example: On-Screen Display during
playing DVD
Items
Selection Method
Title Number
1/3
Chapter Number
1 / 12
Time search
Audio language
and Digital Audio
Output mode
Subtitle
language
0:20:09
Resume play from this point
Action prohibited or not available
ABC
Angle
1 ENG
Sound
Bypass
/ or
S-TITLE
/
/ or
SOUND
Example: On-Screen Display during playing
VCD
Selection Method
Items
1/3
Track Number
0:20:09
Time
/ , Numbers or
SELECT/ENTER
Numbers, SELECT/ENTER
/
Audio Channel
or
AUDIO
Bypass
Sound
/ or
SOUND
Example: On-Screen Display during playing
DivX movie disc
Selection Method
Title Number
1/3
Chapter Number
1 / 12
Time search
Audio language
and Digital Audio
Output mode
Subtitle
language
Sound
14
Numbers, SELECT/ENTER
1/3
Items
Notes
• Some discs may not provide all of the features on the
on-screen display example shown below.
• If no button is pressed for 10 seconds, the on-screen
display disappears.
/ , Numbers or
SELECT/ENTER
/ or
AUDIO
Repeat title
Repeat sequence
/ , Numbers or
SELECT/ENTER
0:20:09
/ , Numbers or
SELECT/ENTER
/ , Numbers or
SELECT/ENTER
Numbers, SELECT/ENTER
/ or
AUDIO
ABC
1 ENG
Bypass
/ or
S-TITLE
/ or
SOUND
Before Operation
DISPLAY
By using the Setup menu, you can make various adjustments to items such as picture and sound. You can also
set a language for the subtitles and the Setup menu,
among other things. For details on each Setup menu
item, see pages 15 to 18.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
Press on the remote control.
To go back to the previous level:
Press on the remote control.
General Operation
1
2
3
4
5
DISPLAY
TV Aspect
16 : 9
Display Mode
Widescreen
Progressive Scan
Off
Move
PREPARATION
Initial Settings
Select
TV Aspect DVD
4:3: Select when a standard 4:3 TV is connected.
16:9: Select when a 16:9 wide TV is connected.
Display Mode DVD
Press SETUP.
The setup menu appears.
Use
/
to select the desired option then
press to move to the second level.
The screen will be shown the current setting for the
selected item, as well as alternate setting(s).
Use
/
to select the second desired option
then press to move to the third level.
Use
/
to select the desired setting then
press SELECT/ENTER to confirm your selection.
Some items require additional steps.
Press SETUP or PLAY to exit the setup menu.
Display Mode setting works only when the TV Aspect
mode is set to “4:3”.
Letterbox: Displays a wide picture with bands on the
upper and lower portions of the screen.
Panscan: Automatically displays the wide picture on
the entire screen and cuts off the portions that do not fit.
Progressive Scan DVD
Progressive Scan Video provides higher quality pictures
with less flickering.
If you are using the Component Video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set Progressive Scan to On.
To Turn ON progressive scan:
LANGUAGE
Connect component out of the DVD to the input of your
monitor/television, set your television or monitor to
Component Input.
1. Select “Progressive Scan” in the DISPLAY menu
then press .
2. Select “On” using the
/
buttons.
3. Press SELECT/ENTER to confirm your selection.
The confirm menu will appear.
LANGUAGE
OSD
English
Disc Audio
Original
Disc Subtitle
Off
Disc Menu
Original
Move
Select
OSD
Select a language for the Setup menu and on-screen display.
4. When the confirm menu appears on your screen
“Cancel” is highlighted as default. Use the /
buttons to highlight “Enter”.
5. Pressing SELECT/ENTER will set the player to
Progressive scan mode.
Disc Audio / Subtitle / Menu DVD
Select the language you prefer for the audio track (disc
audio), subtitles, and the disc menu.
Original: Refers to the original language in which the
disc was recorded.
Other: To select another language, press number buttons to enter the corresponding 4-digit number according to the language code list on page 29. If you enter
the wrong language code, press CLEAR on the remote
control.
Caution
Once the setting for progressive scan output is entered,
an image will only be visible on a progressive scan
compatible TV or monitor. If you set Progressive Scan
to On in error, you must reset the unit.
1) Remove any disc from the unit and close the disc tray.
See that “NO DISC” is displayed in the display window
2) Press and hold STOP (x) for five seconds then
release it. The video output will be restored to the
standard setting, and a picture will once again be
visible on a conventional analog TV or monitor.
15
Before Operation
Size
Press
/ to set a mode. (Large, Small or None)
• You cannot change the size of the front L/R speaker,
which is set to “Large”.
• The size of the Subwoofer can be selected to “Large”
or “None”.
• Since the size of the Center and Rear L/R speaker
are fixed to “Small”, you can not change settings.
AUDIO
AUDIO
5.1 Speaker Setup
Select
DRC
On
Vocal
On
Move
Select
5.1 Speaker Setup DVD
Select speaker settings, including volume balance and
distance, or test the speaker settings.
Speaker settings are only active on the Analog MultiChannel Output.
Speaker Setup
Adjust the following settings for the built-in 5.1 channel
surround decoder.
Size
Front L
Small
Volume
0
dB
Distance
0
m
Test
Off
Select
Return
ENTER
2. Use
/
to select the AUDIO option then press
to move to the second level.
3. Use
/
to select the Speaker Setup option then
press to move to the third level. “Select” is highlighted.
4. Press SELECT/ENTER and 5.1 Speaker Setup
menu appears.
/
Test
Front L → Center → Front R → Rear R →Rear L → Woofer
Move
1. Press SET UP.
The setup menu appears.
5. Use
Distance
If you connected speakers to your DVD/CD Receiver,
setting the distance lets the speakers know how far the
sound has to travel to reach your set listening point.
This allows the sound from each speaker to reach the
listener at the same time.
Press / to adjust the Distance of the selected
speaker.
Select “All” to test the signals of each speaker.
Adjust the volume to match the volume of test signals
memorized in the system.
The subwoofer will not work when the size of the subwoofer is set to “None”.
AUDIO
Speaker
Volume
Press / to adjust the output level of the selected
speaker. (-5dB ~ +5dB)
to select the desired speaker.
6. Adjust options using
/
/ / buttons.
7. Press SELECT/ENTER to confirm your selection.
The unit returns to the previous menu.
Dynamic Range Control (DRC) DVD
With the DVD format, you can hear a program’s soundtrack in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing dialog intelligibility. Set
DRC to On for this effect.
Notes
• The DRC function works only during playback of
Dolby Digital recorded discs.
• The level of Dynamic Range Compression may differ
depending on the DVD disc.
Speaker
Vocal DVD
Select a speaker that you want to adjust.
[Front speaker (Front L), Front speaker (Front R),
Center Speaker (Center), Subwoofer (Woofer), Rear
speaker (Rear L), Rear speaker (Rear R)]
Set Vocal to On only when a multi-channel Karaoke
DVD is playing. The karaoke channels on the disc will
mix into a normal stereo sound.
ote
Certain speaker settings are prohibited by the Dolby
Digital licensing agreement.
16
Before Operation
Password (Security Code)
LOCK (Parental Control)
Rating
Unlock
Password
****
Area Code
RU
AO
Move
1 Select Password on the LOCK menu then press .
2 Follow step 2 as shown left (Rating). “Change” or
“New” is highlighted.
3 Enter the new 4-digit code, then press
SELECT/ENTER. Input it again to verify.
4 Press SETUP to exit the menu.
Select
Rating DVD
Some movies contain scenes that may not be suitable
for children to view. Many of these discs contain parental
control information that applies to the complete disc or to
certain scenes on the disc. Movies and scenes are rated
from 1 to 8, depending on the country. Some discs offer
more suitable scenes as an alternative.
The parental control feature allows you to block access
to scenes below the rating you input, thereby preventing
your children from being able to view material you
believe is unsuitable.
“Rating” on the LOCK menu then press
1 Select
.
access the Rating, Password and Area Code
2 Tofeatures,
you must input the 4-digit security
code you created.
If you have not yet entered a security code you are
prompted to do so.
Input a 4-digit code and press SELECT/ENTER.
Enter it again and press SELECT/ENTER to verify.
If you make a mistake before pressing
SELECT/ENTER, press CLEAR.
a rating from 1 to 8 using the
/
3 Select
buttons.
Rating 1-8: Rating one (1) has the most restrictions
and rating eight (8) is the least restrictive.
Unlock
If you select unlock, parental control is not active
and the disc plays in full.
If you forget your Security Code
If you forget your security code you can clear it using
the following steps:
1 Select Password on the LOCK menu.
2 Input the 6-digit number “210499” on the setup menu
and the security code is cleared.
3 Enter a new code as described above.
ote
When “ PASSWD
” appears on the TV screen, press
STOP (x) and then press SETUP to move to the setup
menu.
Area Code DVD
Enter the code of the country/area whose standards
were used to rate the DVD video disc, based on the list
in the reference chapter.
“Area Code” on the LOCK menu then
1 Select
press .
2 Follow step 2 as shown left (Rating).
3 Select the first character using / buttons.
the cursor using button and select the
4 Shift
second character using
/
buttons.
To complete the area code selection, press
5 SELECT/ENTER.
ote
If you set a rating for the player, all disc scenes with the
same rating or lower are played. Higher rated scenes
are not played unless an alternate scene is available on
the disc. The alternative must have the same rating or a
lower one. If no suitable alternative is found, playback
stops. You must enter the 4-digit password or change
the rating level in order to play the disc.
SELECT/ENTER to confirm your rating
4 Press
selection, then press SETUP to exit the menu.
17
PREPARATION
You can enter or change password.
LOCK
Before Operation
Operation with DVD and Video CD
OTHERS
Playing a DVD and Video CD
OTHERS
Playback Setup DVD
PBC
On
DivX(R) Registration
Select
Move
Select
PBC VCD
Set Playback Control (PBC) to On or Off.
On:Video CDs with PBC are played according to the
PBC.
Off:Video CDs with PBC are played the same way as
Audio CDs.
DivX(R) Registration
VCD
• Turn on the TV and select the video input source
connected to the unit.
• Audio system: Turn on the audio system and select
the input source connected to the unit.
1 Press ZOP./CL. button to open the disc tray.
your chosen disc in the tray, with the
2 Load
playback side facing down.
Press ZOP./CL. button to close the tray.
3 Playback
starts automatically. If playback does not
start, press PLAY.
In some cases, the disc menu might appear
instead.
DivX
You can show the DivX DRM (Digital Right
Management) Registration code for your unit only.
Your registration code is : XXXXXXXX
Please use this code to register this player with
the DivX(R) Video On Demand service.
This will allow you to rent and purchase videos
using the DivX(R) Video On Demand format.
To learn more go to www.divx.com/vod
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD or Video CD which contains a menu.
DVD
Use the
/
/ / buttons to select the title/chapter
you want to view, then press SELECT/ ENTER to start.
Press TITLE or MENU to return to the menu screen.
VCD
The Registration code is used for VOD (Video-OnDemand) service agent. You can purchase or rental an
encrypt movie file.
Notes
If you rent the DivX VOD file, it has several options of
viewing limits as show below.
• Display the number which you can watch the file.
! This rental video has 3 views left. A view
ends when you stop playback, play a different
video, or turn off your player.
Do you want to use one of your 3 views now
Yes
No
• The rental has been expired.
!
This rental is expired.
• Display the authorization error.
!
This video player is not authorized to
play this video.
18
Use the number buttons to select the track you want to
view and press RETURN to return to the menu screen.
Menu setting and the exact operating procedures for
using the menu may differ depending on the disc.
Follow the instructions on the each menu screen.
You also may set PBC to Off.
Notes
– If parental control is set and the disc is not within the
rating settings you must input the password.
(See “LOCK” on page 17.)
– DVDs may have a region code. Your player will not
play discs that have a region code different from your
player. The region code for this player is 5 (five).
To Select a disc directly
Press DISC 1, DISC 2 or DISC 3 on the front panel
during playing or stopping.
The unit will automatically start playing the selected
disc.
Operation with DVD and Video CD
Slow Motion
ote
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
Moving to another TITLE
DVD
DivX
When a disc has more than one title, you can move to
another title. Press DISPLAY while playback is stopped
then the appropriate number (0-9) or use / to move
to another title.
You can play any title by inputting its number while playback is stopped.
Moving to another CHAPTER/TRACK
DVD
VCD
DVD
VCD
VCD
1 Press PAUSE/STEP on the remote control during
playback.
The player will now go into PAUSE mode.
2 Use the m or M to select the required speed: t
1/2, t 1/4, t 1/8 or t 1/16 [(backward) - DVD
only] or T 1/2, T 1/4, T 1/8 or T 1/16
(forward).
3 To return to normal PLAY, press PLAY.
ote
Slow motion playback in reverse is not applicable for
Video CD.
Repeat
DVD
VCD
DivX
You can play a title/chapter/all/track on a disc.
Press REPEAT during playback to select a desired
repeat mode.
DivX
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
• Press . or > briefly during playback to select
the next chapter/track or to return to the beginning of
the current chapter/track.
• Press . twice briefly to step back to the previous
chapter/track.
• To go directly to any chapter during DVD playback,
press DISPLAY and press
/
to select the chapter/track icon. Then, input the chapter/track number or
use / .
Search
DVD
DivX
1 Press m or M during playback.
The player will now go into SEARCH mode.
2 Press m or M repeatedly to select the required
speed: mX2, mX4, mX8, mX16, mX100
(backward) or MX2, MX4, MX8, MX16,
MX100 (forward).
With a DivX/ Video CD, the Search speed changes:
mX2, mX4, mX8, mX16 (backward) or MX2,
MX4, MX8, MX16 (forward).
DVD Video Discs - Repeat Chapter/Title/Off
• Chapter: repeats the current chapter.
• Title: repeats the current title.
• Off : does not play repeatedly.
DivX/ Video CDs - Repeat Track/All/Off
• Track : repeats the current track
• All : repeats all the tracks on a disc.
• Off : does not play repeatedly.
ote
– On a Video CD with PBC, you must set PBC to Off on
the setup menu to use the repeat function (See “PBC”
on page 18).
Repeat A-B
DVD
VCD
To repeat a sequence in a title:
1 Press REPEAT A-B at your chosen starting point.
“ A - ” appears briefly on the TV screen.
2 Press REPEAT A-B again at your chosen end point.
“A - B” appears briefly on the TV screen, and the
repeat sequence begins.
3 To cancel the sequence, press REPEAT A-B.
Still Picture and Frame-by-frame playback
DVD
VCD
DivX
1 Press PAUSE/STEP on the remote control during
playback.
The player will now go into PAUSE mode.
2 You can advance the picture frame-by-frame by
pressing PAUSE/STEP repeatedly on the remote control.
3 To exit still motion mode, press PLAY.
19
OPERATION
General Features
Operation with DVD and Video CD
General Features (continued)
To clear a Marked Scene
1 During disc playback, press SEARCH.
Time Search
DVD
VCD
DivX
The Time Search function allows you to start playing at
any chosen time on the disc.
1 Press DISPLAY during playback. The on-screen
display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
2 Within 10 seconds, press
/
to select the Time
Search icon in the on-screen display.
The MARKER SEARCH menu will appear on the screen.
2 Press / to select the Marker number that you
want to erase.
3 Press CLEAR.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
The “-:--:--” appears in the Time Search box.
3 Within 10 seconds, use the number buttons to enter
the required start time. Enter hours, minutes, and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
4 Within 10 seconds, press SELECT/ENTER to confirm
the start time.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
Zoom
DVD
VCD
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
1 Press ZOOM during playback or still playback to
activate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to four steps.
100% size → 400% size → 800% size →
1600% size → 100% size
2 Use the
/
/ / buttons to move through the
zoomed picture.
ote
– On a Video CD with PBC, you must set PBC to Off on
the setup menu to use the time search function (See
“PBC” on page 18).
Special DVD Features
Checking the contents of DVD Video
discs: Menus
DVDs may offer menus that allow you to access special
features. To use the disc menu, press MENU. Then,
press the appropriate number button to select an option.
Or, use the
/
/ / buttons to highlight your
selection, then press SELECT/ENTER.
Title Menu
DVD
DivX
1 Press TITLE.
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
ote
The zoom function may not work for some DVDs.
3 To remove the title menu, press TITLE again.
Marker Search
Disc Menu
DVD
VCD
DivX
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when
playback reaches the spot that you want to
memorize.
The Marker icon will appear on the TV screen briefly.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
To Recall a Marked Scene
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
2 Within 10 seconds, press / to select a Marker
number that you want to recall.
3 Press SELECT/ENTER.
Playback will start from the Marked scene.
4 To remove the MARKER SEARCH menu, press
SEARCH.
20
DVD
DivX
Press MENU.
The disc menu is displayed.
Camera Angle
DVD
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
1 Press DISPLAY and then press the
/
to select
a angle.
The number of the current angle appears in the display
window.
2 Select a desired angle pressing the
/
buttons.
Operation with DVD and Video CD
Operation with Audio CD and MP3/WMA Disc
Special DVD Features (continued) Playing an Audio CD and MP3/WMA
DVD
DivX
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
Changing the Audio Channel
VCD
Press AUDIO repeatedly during playback to hear a
different audio channel (STER., LEFT or RIGHT).
file
CD
MP3
WMA
The unit can play audio CD and MP3/WMA.
Audio CD
Once you insert an audio CD a menu appears on the TV
screen. Press
/
to select a track then press PLAY
or SELECT/ENTER and playback starts.
1:04:36
1 / 12
Audio CD
Subtitle
DVD
Program
List
DivX
Track1
Track2
Track3
Press S-TITLE repeatedly during playback to see the
different subtitle languages.
Track4
Track5
Track6
Track7
Track8
If
ote
appears, the feature is not available on the disc.
Last Scene Memory
DVD
This player memorizes last scene from the last disc that
is viewed. The last scene remains in memory even if
you remove the disc from the player or switch off the
player. If you load a disc that has the scene memorized,
the scene is automatically recalled.
MP3 / WMA
1. Press
/
to select a folder, and press
SELECT/ENTER to see the folder contents.
2. Press
/
to select a track then press PLAY or
SELECT/ENTER. Playback starts.
0:00:00
MUSIC
1 / 104
PHOTO
MOVIE
Program
List
Music1
Music2
Music3
ote
This player does not memorize the scene of a disc if
you switch off the player before commencing to play the
disc.
Screen Saver
The screen saver appears when you leave the DVD
player in Stop mode for about five minutes.
Music4
Music5
Music6
Music7
otes
• If you are in a file list on the MUSIC menu and want to
return to the Folder list, use the
/
to highlight
on the stop mode and press SELECT/ENTER.
• Press MENU to move to the next page.
• On a CD with MP3/WMA file and JPEG file, you can
switch MP3/WMA and JPEG menu. Press TITLE on
the stop mode and MP3/WMA or JPEG word on top of
the menu is highlighted. Then, use
/
to select
MP3/WMA or JPEG then press SELECT/ENTER.
• The MP3 file name and ID3 TAG should be named
using English.
Pause
CD
MP3
WMA
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP again.
Moving to another Track
CD
MP3
WMA
• Press . or > briefly during playback to go to the
next track or to return to the beginning of the current
track.
• Press . twice briefly to step back to the previous track.
• In case of audio CD, to go directly to any track, enter
the track number using the numbered buttons (0-9)
during playback.
21
OPERATION
Changing the Audio Language
Programmed Playback
Operation with Audio CD and MP3/WMA Disc
Repeat Track/All/Off
CD
MP3
WMA
You can play a title/chapter/all/track on a disc.
1 Press REPEAT when playing a disc. The repeat icon
appears.
2 Press REPEAT to select a desired repeat mode.
• Track: repeats the current track
• All: repeats all the tracks on a disc.
• Off (No display) : does not play repeatedly.
CD
MP3
WMA
The Program function enables you to store your favorite
tracks from any disc in the player memory.
A program can contain 300 tracks (Audio CD/MP3/WMA).
Insert a disc.
1
Audio CD and MP3/WMA Discs:
Audio CD or MP3/WMA menu appears as below.
1:04:36
0:00:00
1 / 12
MUSIC
Audio CD
List
1 / 104
PHOTO
List
Program
MOVIE
Program
Track1
Music1
Track2
Music2
Track3
Music3
Track4
Search
CD
MP3
Music4
Track5
WMA
Music5
Track6
Music6
Track7
Music7
Track8
1 Press m or M during playback.
The player will now go into SEARCH mode.
2 Press m or M repeatedly to select the required
speed: mX2, mX4,mX8 (backward) or MX2,
MX4, MX8 (forward).
3 To exit SEARCH mode, press PLAY.
MP3 / WMA disc compatibility with this player is
limited as follows:
• Sampling frequency: within 32 - 48 kHz (MP3),
within 24 - 48kHz (WMA)
• Bit rate: within 32 - 320kbps (MP3),
40 - 192kbps (WMA)
• The player cannot read an MP3/WMA file that has a
file extension other than “.mp3” / “.wma”.
• CD-R physical format should be ISO 9660
• If you record MP3 / WMA files using software that
cannot create a file system (eg. Direct-CD) it is
impossible to playback MP3 / WMA files. We recommend that you use Easy-CD Creator, which creates an ISO 9660 file system.
• File names should have a maximum of 8 letters and
must incorporate an .mp3 or .wma extension.
• They should not contain special letters such as / ?
* : “ < > l etc.
• The total number of files on the disc should be less
than 999.
This unit requires discs and recordings to meet certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically set to these standards. There are many different
types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain
pre-existing conditions (see above) to ensure compatible playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has no
right to grant such permission. Permission should
always be sought from the copyright owner.
Audio CD Menu
MP3/WMA Menu
2 Select a track on the List.
PROG./MEMO.. Or, select “
(Add)” icon
3 Press
then SELECT/ENTER to place the selected track
on the Program list. Repeat to place additional
tracks on the list.
ote
You can add all tracks in the disc. Select “
(Add All)”
icon then press SELECT/ENTER.
Select the track you want to start playing on the
Program list.
4
Tip
Press MENU to move to the next page.
PLAY or SELECT/ENTER to start.
5 Press
Playback begins in the order in which you programmed the tracks and “PROG.” appears in the
display window. Playback stops after all of the tracks
on the Program list have played once.
ote
To resume normal playback from programmed playback, select
a track of AUDIO CD (or MP3/WMA) list and then press PLAY.
Repeat Programmed Tracks
You can play a title/chapter/all/track on a disc.
1 Press REPEAT when playing a disc. The repeat icon
appears.
2 Press REPEAT to select a desired repeat mode.
• TRACK: repeats the current track
• ALL: repeats all the tracks on a disc.
• Off (No display): does not play repeatedly.
Erasing a Track from Program List
1 Use
/
/ / to select the track that you wish to
erase from the Program list.
2 Press CLEAR. Or, select “
(Delete)” icon then Press
SELECT/ENTER to place the selected track on the
Program list. Repeat to erase additional tracks on the list.
Erasing the Complete Program List
Select “
(Del all)”, then press SELECT/ENTER. The
complete Program for the disc is erased.
ote
The programs are also cleared when the disc is removed.
22
Operation with JPEG Disc
JPEG
Slide Show JPEG
This unit can play discs with JPEG files.
Before playing JPEG recordings, read the notes on
JPEG Recordings on right.
Use
/
/ / to highlight the
then press SELECT/ENTER.
1
Moving to another File JPEG
Insert a disc and close the tray.
The PHOTO menu appears on the TV screen.
(Slide Show)
OPERATION
Viewing a JPEG disc
Press . or > once during viewing a picture to
advance to the next file or to the previous file.
PHOTO
List
Preview
JPEG Folder 1
JPEG Folder 2
Still Picture
JPEG
JPEG Folder 3
JPEG Folder 4
JPEG Folder 5
JPEG Folder 6
JPEG Folder 7
JPEG Folder 8
/
to select a folder, and press
2 Press
SELECT/ENTER. A list of files in the folder
appears.
Tip
If you are in a file list and want to return to the Folder
list, use the
/
buttons on the remote control to
highlight “
” and press SELECT/ENTER to return to
the previous menu screen.
you want to view a particular file, press
3 IfSELECT/ENTER
/
to highlight a file and press
or PLAY.
Slide Show starts from the selected file if Speed
option is not Off.
While viewing a file, you can press STOP(x) to
move to the previous menu (JPEG menu).
Tip
• Press MENU to move to the next page.
• There are four Slide Speed options:
:
> (Slow), >> (Normal), >>> (Fast) and II (off).
Use
/
/ / to highlight the Speed. Then, use
/ to select the option you want to use then press
SELECT/ENTER.
• If you set Speed option to Off, Slide Show is not
active.
1 Press PAUSE/STEP during slide show.
The player will now go into PAUSE mode.
2 To return to the slide show, press PLAY or press
PAUSE/STEP again.
To rotate picture JPEG
Press
/
/ / during showing a picture to rotate
the picture clockwise or counter-clockwise.
Zoom JPEG
The Zoom function allows you to enlarge or reduce the
video image.
1 Press ZOOM repeatedly.
Zoom on y Zoom off
2 Use the
/
/ / buttons on the “Zoom on”
mode.
JPEG disc compatibility with this player is limited
as follows:
• Depending upon the size and number of JPEG files,
it could take a long time for the DVD player to read
the disc’s contents. If you don’t see an on-screen
display after several minutes, some of the files may
be too large — reduce the resolution of the JPEG
files to less than 2760 x 2048 pixels and burn
another disc.
• The total number of files and folders on the disc
should be less than 999.
• Some discs may be incompatible due to a different
recording format or the condition of disc.
• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
• If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” file.
• File names without “.jpg” extension will not be able
to be read by this DVD player. Even though the files
are shown as JPEG image files in Windows
Explorer.
23
Operation with DivX Disc
The unit can play the DivX files.
1
Insert a disc and close the tray.
The DivX menu appears on the TV screen.
0:00:00
1 / 12
DivX disc compatibility with this player is limited
as follows:
• Available resolution size of the DivX file is under
720x576 (W x H) pixel.
MOVIE
List
Movie Folder 1
Movie Folder 2
Movie Folder 3
Movie Folder 4
Movie Folder 5
Movie Folder 6
Movie Folder 7
• The file name of the DivX subtitle is available by
20-40 characters (differs from language).
• If there is impossible code to express in the DivX
file, it may be displayed as " _ " mark in the
display.
Movie Folder 8
• If the number of the screen frame is over 30 per
1 second, this unit may not operate normally.
/
to select a folder, and press
2 Press
SELECT/ENTER to see the folder contents.
Tip
If you are in a file list and want to return to the Folder
list, use the
/
buttons on the remote control to
highlight “
” and press SELECT/ENTER to return to
the previous menu screen.
to view a particular file, press
3 If you/ want
to highlight a file and press
SELECT/ENTER or PLAY.
Playback starts.
4
• If the video and audio structure of recorded file
is not interleaved, either video or audio is outputted.
Playable DivX subtitle file
z SubRip(*.srt/*.txt)
SAMI(*.smi)
SubStation Alpha(*.ssa/*.txt)
MicroDVD(*.sub/*.txt)
SubViewer 2.0(*.sub/*.txt)
VobSub(*.sub)
Playable DivX file
z ".avi ", ".mpg ", ".mpeg "
x) to exit.
Press STOP(x
Playable Codec format
otes
z "DIVX3.xx ", "DIVX4.xx ", "DIVX5.xx ", "XVID ",
"MP43 ", "3IVX ", "MP42 ".
• Be sure to select “SUBTITLE ON” mode by pressing the
subtitle file every time before playing a DivX file .
• When the subtile has more than two languages in the file,
original subtile is only available.
• The DivX files in your memory card can not be played.
• The microphone does not work during playing a DivX file.
• You can not adjust the sound mode and VIRTUAL sound
during playing a DivX file.
Notice for displaying the Divx subtitle
If the subtitle does not display properly during playback,
press and hold S-TITLE about 3 seconds then press STITLE to select another language code until the subtitle is
displayed properly.
24
Playable Audio format
z "AC3 ", "DTS ", "PCM ", "MP3 ", "WMA ".
• Sampling frequency: within 32 - 48 kHz (MP3),
within 24 - 48kHz (WMA)
• Bit rate: within 32 - 320kbps (MP3),
40 - 192kbps (WMA)
Operation with RADIO
Listening to the radio
You can preset 50 stations for FM and AM.
Before tuning, make sure that you have turned the volume down to the minimum level.
1
Press TUNER/BAND on the remote control to
show either FM or AM in the display window. Or
Press TUNER on the front panel.
Every time you press this button, AM and FM
changes alternately.
2 remote
TUNING (-/+) on the front panel or
control.
Select a station you want by pressing
/
Press TUNER/BAND on the remote control to
show either FM or AM in the display window. Or
Press TUNER on the front panel.
The last received station is tuned in.
the preset station you want.
2 toEachselect
time you press this button, the unit tunes in
Press
/
on the remote control repeatedly
the next preset station.
KNOB (or pressing VOLUME (-/+) on
3 CONTROL
the remote control) repeatedly.
Adjust the volume by rotating VOLUME
on the
To listen to non-preset radio stations
otes
• Automatic Tuning
Press TUNING (-/+) or / for more than 0.5
second.
- Scanning stops when the unit tunes in a station.
• Manual Tuning
Press TUNING (-/+) or
1
/
briefly and repeatedly.
3
Press
/
on the remote control to select the
4 preset number you want.
Press PROG./MEMO. again.
5 The station is stored.
Repeat steps 1 (or 2) to 5 to store other stations.
6
Press PROG./MEMO. on the remote control.
A preset number will flash in the display window.
To clear all memorized stations
Press and hold PROG./MEMO. on the remote control for
about two seconds, “ERASE ALL” appears in the display
window and then press PROG./MEMO. on the remote
control, the stations are cleared.
• For manual tuning, see “Manual Tuning”.
• For automatic tuning, see “Automatic Tuning”.
To select a preset radio station directly
You can use the number buttons on the remote control
to select a preset radio station directly.
For example, to listen to preset station 4, press 4 on the
remote control. To listen to preset station 19, press 1
then 9 (within 3 seconds).
To turn the radio off
Press POWER to turn off the unit or select another
function mode (DVD, TAPE, AUX or USB).
For your reference
• If a FM program is noisy
Press ST./MO. repeatedly so that that “
”
disappears in the display window. There will be no
stereo effect, but the reception will improve. Press
ST./MO. again to restore the stereo effect.
• To improve reception
Reposition the supplied antennas.
For your reference
If all stations have already been entered, “FULL”
message will appear in the display window for a
moment and then a preset number will flash.
To change the preset number, follow the steps 4-5 .
To recall preset numbers
Press and hold
/
on the remote control until the
desired preset number appears or press the button
repeatedly.
25
OPERATION
Presetting the radio stations
Operation with RADIO
RDS Function : OPTIONAL
Programme Search (PTY) : OPTIONAL
About RDS : OPTIONAL
A major benefit of RDS is its ability to encode broadcasts with Programme Type (PTY) codes that indicate
the type of material being broadcast. The following list
shows the abbreviations used to indicate each PTY
along with an explanation of the PTY.
This unit is equipped with RDS (Radio Data System),
which brings a wide range of information from FM radio.
RDS is a system for transmitting station call signs or
network information, a description of station programme
type text message about the station or specifics of
musical selection and the correct time.
RDS Tuning : OPTIONAL
When a FM station containing RDS data is tuned in, the
unit will automatically display the station’s call sign and
the RDS indicator will light in the Display Window as
well as indicators for the programme type recognition
(PTY), Radio Text (RT), Clock Time (CT) and RDS
services programme (PS) if transmitted by the station.
RDS Display Options : OPTIONAL
The RDS system is capable of transmitting a wide
variety of information in addition to the initial call sign
that appears when a station is first tuned. In normal
RDS operation the display will indicate the station name,
broadcast network or call letters. Pressing RDS on the
front panel enables you to cycle through the various
data types in the sequence:
(FREQUENCY
PTY
RT
CT
PS)
• PTY (Programme type recognition)The programme type is shown in the display window.
• RT (Radio text recognition)- The radio station’s
name is displayed in the display window.
• CT (Time controlled by the channel)- Enable the
unit to receive the actual time and show it on the
display window.
• PS (Programme Service name)- The programme
title is displayed in the display window.
ote
Some RDS stations may not choose to include some of
these additional features. If the data required for the
selected mode is not being transmitted, the Display
Window will show a PTY NONE, RT NONE, CT NONE,
PS NONE message.
You may search for a specific Programme Type (PTY)
by following these steps:
TUNER (or TUNER/BAND) to select FM
1 Press
mode.
PTY on the remote control, the display
2 Press
will show the last PTY in use.
3 Press PTY repeatedly to select a desired PTY.
4 When the PTY is selected, press and hold PTY.
The unit will go into an automatic search mode.
When a station is tuned, the search will stop.
26
Basic Playback
To Stop Play
1
Open cassette TAPE1-2 by pushing to the
2 PUSH EJECT position.
one or two cassettes with the tape side to
3 Insert
the bottom and then close the TAPE 1 (and/or 2)
Press STOP( ) on the front panel or TAPE STOP( )
on the remote control during playback.
Press TAPE1-2 (or TAPE) to select tape function.
(“NO TAPE ” appears in the display window.)
4
To Play Rewind or Fast Forward
door.
BB > on the front panel or
After press . bb/B
FF/GG on the remote control during playback,
press G (or F) at the tape position you want.
Press G (or F: OPTIONAL).
Dubbing
This function shows how to record from tape to tape.
AUTO STOP DECK (TAPE 1)
After auto stop deck plays front side of cassette, the unit
stops automatically.
AUTO REVERSE DECK (TAPE 2)
You can select direction of the cassette you want by
pressing PLAY MODE.
Pressing
Display
Function
-
After the cassette of TAPE 1 or 2
plays front or reverse (backward
play) side, stops automatically.
Once
After the cassette of TAPE 1 or 2
plays front and reverse side,
stops automatically.
Twice
After the cassette of TAPE 1 or 2
plays six times repeatedly front and
reverse side, stops automatically.
1
Press TAPE1-2 (or TAPE).
• Cassette TAPE 1- Insert the playback tape to dub.
• Cassette TAPE 2- Insert a blank tape to copy on.
DUBBING - Normal speed copying
2 •• NORMAL
HIGH DUBBING - Double speed copying
Press NOR-DUBB./HI-DUBB..
To stop recording, press STOP (x).
Recording
Basic Setting
1
2
Select a function you want to record except tape
function.
Open the cassette deck TAPE 2 and insert a
blank cassette into the cassette compartment.
Set the recording direction
Press PLAY MODE repeatedly to set the recording
direction.
Recording from Radio, CD or Auxiliary source
1
2
Press zREC/[] on the front panel or z/[] on the
remote control.
“REC” flashes and holds the cassette in pause
mode.
Press G (or F).
The recording begins.
To pause the recording
CD to Tape Synchronized Recording
The CD synchro recording function dubs a complete CD
and programmed titles automatically into a cassette.
1
2
3
Press DVD button on the remote zcontrol.
Press CD SYNC. in stop mode.
“REC” flashes and “CD SYNC” displays in the display window.
The synchronized recording is started
automatically after about 7 seconds.
otes
• If you wish to record from the desired track, select
the desired track with . bb/BB > or FF/GG
before commencing CD synchro recording.
• A function change is not possible during recording.
Press z/[] or zREC/[].
To Stop the recording
Press STOP(x).
27
OPERATION
Operation with TAPE
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Symptom
Correction
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet
securely.
The power is on, but the
unit does not work.
• No disc is inserted.
• Insert a disc. (Check that the DVD or, audio
CD indicator in the DVD display is lit.)
No picture.
• The TV is not set to receive DVD signal output.
• Select the appropriate video input mode on
the TV so the picture from the unit appears on
the TV screen.
• The video cable is not connected securely.
• Connect the video cable into the jacks securely.
• The connected TV power is turned off.
• Turn on the TV.
• The equipment connected with the audio
cable is not set to receive DVD signal output.
• Select the correct input mode of the audio so
you can listen to the sound from the unit.
• The audio cables are not connected securely
.
• Connect the audio cable into the jacks
securely.
• The power of the equipment connected with
the audio cable is turned off.
• Turn on the equipment connected with the
audio cable.
There is no sound or only
a very low-level sound is
heard.
• The audio connecting cord is damaged.
• Replace it with new one.
The playback picture is poor.
• The disc is dirty.
• Clean the disc.
The unit does not start
playback.
• No disc is inserted.
• Insert a disc. (Check that the DVD, or audio
CD indicator in the DVD display is lit.)
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc type,
color system and Regional code.)
• The disc is placed upside down.
• Place the disc with the playback side down.
• The disc is not placed within the guide.
• Place the disc on the disc tray correctly inside
the guide.
• The disc is dirty.
• Clean the disc.
• A menu is on the TV screen.
• Press the SET-UP button to turn off the menu
screen.
• The Rating level is set.
• Cancel the Rating function or change the rating level.
• The plugs and jacks are dirty.
• Wipe them with a cloth slightly moistened with
alcohol.
• The disc is dirty.
• Clean the disc.
• The speakers and components are
connected poorly.
• Connect the speakers and components
securely.
• The unit is located with too close to the TV.
• Move your TV away from the audio components.
• The antenna is positioned or connected
poorly.
• Connect the antenna securely.
• The signal strength of the stations is too
weak (when tuning in with automatic tuning).
• Tune in the station manually.
• No stations have been preset or preset stations have been cleared (when tuning by
scanning preset stations).
• Preset the stations.
• The remote control is not pointed at the
remote sensor of the unit.
• Point the remote control at the remote sensor
of the unit.
• The remote control is too far from the unit.
• Operate the remote control within about 23 ft
(7 m).
• There is an obstacle in the path of the
remote control and the unit.
• Remove the obstacle.
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
• The DVD/CD function is not selected.
• Select the DVD/CD function by pressing DVD
Severe hum or noise is
heard.
Radio stations cannot be
tuned in.
The remote control does
not work properly.
The disc tray is not
opened
28
• Adjust the antennas and connect an external
antenna if necessary.
button. And then press the ZOP./CL. button.
Language Code List
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Code
6566
6565
6570
8381
6577
6582
7289
6583
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
7074
Language
Finnish
French
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Lingala
Lithuanian
Code
7073
7082
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
7678
7684
Language
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Singhalese
Slovak
Code
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
8373
8375
Language
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Area Code List
Choose an area from this list.
Country
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
Country
Code
Ethiopia
ET
Fiji
FJ
Finland
FI
France
FR
Germany
DE
Great Britain
GB
Greece
GR
Greenland
GL
Heard and McDonald
Islands
HM
Hong Kong
HK
Hungary
HU
India
IN
Indonesia
ID
Israel
IL
Italy
IT
Jamaica
JM
Japan
JP
Kenya
KE
Kuwait
KW
Libya
LY
Luxembourg
LU
Country
Code
Malaysia
MY
Maldives
MV
Mexico
MX
Monaco
MC
Mongolia
MN
Morocco
MA
Nepal
NP
Netherlands
NL
Dutch Antilles
AN
New Zealand
NZ
Nigeria
NG
Norway
NO
Oman
OM
Pakistan
PK
Panama
PA
Paraguay
PY
Philippines
PH
Poland
PL
Portugal
PT
Romania
RO
Russian Federation RU
Country
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
Code
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
29
REFERENCE
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Specifications
General
Power supply
Power consumption
Net Weight
External dimensions (W x H x D)
Refer to the main label.
90 W
6.5 kg
272 X 322 X 354 mm
Tuner/Amplifier
FM
Tuning Range
Intermediate Frequency
Signal to Noise Ratio
Frequency Response
AM Tuning Range
Intermediate Frequency
Signal to Noise Ratio
Frequency Response
Output Power
T.H.D
Frequency Response
Signal-to-noise ratio
87.5 - 108.0 MHz or 65 -74 MHz, 87.5 -108.0 MHz
10.7 MHz
60/55 dB (Mono/Stereo)
140 - 10000 Hz
522 - 1620 kHz or 520 - 1720 kHz
450 kHz
30 dB
140 - 1800 Hz
Front: 130 W + 130 W (4 Ω, THD 10 %)
Center: 60 W (8 Ω, THD 10%)
Rear: 60 W + 60 W (8 Ω, THD 10 %)
Subwoofer: 180 W (3 Ω, THD 10 %)
0.5 %
140 - 20000 Hz
75 dB
DVD/VCD/CD player
Frequency response (audio)
Signal-to-noise ratio (audio)
Signal-to-noise ratio (video)
Dynamic range (audio)
Video output
S-video output
Component Video output
Cassette tape player
40 - 20000 Hz
More than 75 dB (1 kHz)
More than 55 dB (1 kHz)
More than 80 dB
1.0 V (p-p), 75 Ω
(Y) 1.0 V (p-p), 75 Ω
(C) 0.3 V (p-p), 75 Ω
(Y) 1.0 V (p-p), 75 Ω
(Pb)/(Pr) 0.7 V (p-p), 75 Ω
Tape Speed
Wow Flutter
F.F/REW. Time
Frequency Response
Signal to Noise Ratio
Channel Separation
Erase Ratio
3000 ± 3 % (MTT-111.
NORMAL-SPEED)
0.25 %
(MTT -111, JIS-WTD)
120 sec (C-60)
250 - 8000 Hz
43 dB
50 dB (P/B)/45 dB (R/P)
55 dB (MTT-5511)
Speakers
Speaker Name
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max. Input Power
Net Dimensions (W x H x D)
Net Weight
Front Speaker (L/R)
Bass Reflex 2Way 3Speaker
4Ω
55 - 20000 Hz
86 dB/W (1m)
130 W
260 W
214 X 386 X 318 mm
6.3 kg
Center Speaker
Bass Reflex 2Way 3Speaker
8Ω
130 - 20000 Hz
84 dB/W (1m)
60 W
120 W
310 X 115 X 136 mm
1.5 kg
Speaker Name
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max. Input Power
Net Dimensions (W x H x D)
Net Weight
Rear Speaker (L/R)
Bass Reflex 2Way 2Speaker
8Ω
60 - 20000 Hz
83 dB/W (1m)
60 W
120 W
194 X 325 X 280 mm
3.6 kg
Subwoofer
Bass Reflex 1Way 1Speaker
3Ω
50 - 15000 Hz
84 dB/W (1m)
180 W
360 W
273 X 325 X 384 mm
6.5 kg
P/NO : MFL38637153
Download PDF

advertising