LG | 55SE3B-B | LG 55SE3B Owner’s Manual

OWNER’S MANUAL
MONITOR
SIGNAGE
Please read this manual carefully before operating the your set and retain it
for future reference.
32SE3B
43SE3B
49SE3B
55SE3B
65SE3B
32SE3KB
43SE3KB
49SE3KB
55SE3KB
65SE3KB
www.lg.com
2
TABLE OF CONTENTS
ENGLISH
TABLE OF CONTENTS
3
SAFETY PRECAUTIONS
30ENTERTAINMENT
3
4
Precautions in installing the product
Precautions to the AC adapter and
electrical power
Precautions in moving the product
Precautions in using the product
Mounting on a wall
30
30
32
32
32
34
36
39
41
43
Using the Network
- Connecting to a Network
- Network Status
Using the My Media
- Connecting USB storage devices
- Browsing Files
- Viewing Movies
- Viewing Photos
- Listening to Music
- Viewing the Contents List
44
CUSTOMIZING SETTINGS
44
45
48
49
50
53
Accessing Main Menus
- PICTURE Settings
- AUDIO Settings
- TIME Settings
- OPTION Settings
- NETWORK Settings
5
5
5
6LICENSES
7
ASSEMBLY AND PREPARATION
7Accessories
8
Optional Accessories
10
Parts and Buttons
12
Connecting the Stand
13
Connecting the Speakers
14
Using the IR Receiver
15
Portrait Layout
16
Attaching and removing the LG Logo
Bracket
17
Installing on a Wall
54TROUBLESHOOTING
56
PRODUCT SPECIFICATIONS
19
REMOTE CONTROL
21
68
IR CODES
21
22
Displaying the Device Name
Connected to an Input Port
White Balance Adjust Menu
Using Picture ID
70
TO CONTROL MULTIPLE
PRODUCTS
23
MAKING CONNECTIONS
23
25
Connecting to a PC
External Device Connection
28
USING THE MONITOR
28
28
Using the Input List
Adjusting Aspect Ratio
70
71
71
71
71
72
74
Connecting the Cable
RS-232C Configurations
- 4P Cable
- RS-232C Cable
Communication Parameter
Command Reference List
Transmission / Receiving Protocol
SAFETY PRECAUTIONS
Please read these safety precautions carefully before using the
product.
WARNING
If you ignore the warning message, you may be seriously injured
or there is a possibility of accident or death.
CAUTION
If you ignore the caution message, you may be slightly injured or
the product may be damaged.
WARNING
•• Indoor Use Only.
Precautions in installing the product
WARNING
•• Keep away from heat sources like electrical heaters.
•• Leaving a fixed image on the screen for a long time may cause
damage to the screen and cause image burn-in. To use the product
for a long period of time, use a screen saver on the PC or utilize
the residual image prevention function on the product, and when
the product is not used, turn off the power. Burn-in and related
problems are not covered by the warranty on this product.
•• Do NOT install this product on a wall where there is high risk of
exposure to oil fumes or mist.
►►
This may damage product and cause is to fail.
CAUTION
•• Make sure the product ventilation hole is not blocked. Install the
product in a suitably wide place (more than 10 cm from the wall)
►►
If you install the product too close to the wall, it may be deformed or
fire can break out due to internal heat.
•• Do not block the ventilation hole of the product by a tablecloth
or curtain.
►►
The product can be deformed or fire can break out due to overheating
inside the product.
•• Install the product on a flat and stable place that has no risk of
dropping the product.
►►
If the product is dropped, you may be injured or the product may
be broken.
►►
Electrical shock, fire, malfunction or deformation may occur.
•• Install the product where no EMI occurs.
•• Keep the product away from direct sunlight.
►►
Anti-moisture material is harmful if swallowed. If swallowed by
mistake, force the patient to vomit and visit the nearest hospital.
Additionally, vinyl packing can cause suffocation. Keep it out of the
reach of children.
•• If you install the product in a place that does not meet the
recommended conditions, this may cause serious damage to the
product’s picture quality, life cycle and appearance. Please check
with LG or a qualified installer before installing. This caution
applies to a place where there is an abundance of fine dust or oil
mist, chemical substances are used, the temperature is very high
or low, the humidity is very high, or the product is likely to remain
turned on for a long period of time (airport and train station),
failure to do so will invalidate the warranty.
•• Do not install the product in an area with poor ventilation (e.g.on
a bookshelf, in a closet) or outside and avoid placing on cushions
or carpets.
•• In addition, do not install it where there are heating objects such
as lighting equipment.i
•• Keep the packing anti-moisture material or vinyl packing out of
the reach of children.
•• Do not put heavy objects on the product or sit upon it.
►►
If the product collapses or is dropped, you may be injured. Children
must pay particular attention.
•• Do not leave the power or signal cable unattended on the
pathway.
►►
The passerby can falter, which can cause electrical shock, fire, product
breakdown or injury.
•• Install the product in a neat and dry place.
►►
Dust or moisture can cause electrical shock, fire or product damage.
•• If you can smell smoke or other odors or hear a strange sound
unplug the power cord and contact the service center.
►►
If you continue to use without taking proper measures, electrical
shock or fire can occur.
•• If you dropped the product or the case is broken, turn off the
product and unplug the power cord.
►►
If you continue to use without taking proper measures, electrical
shock or fire can occur. Contact the service center.
•• Do not drop an object on or apply impact to the product. Do not
throw any toys or objects on the product screen.
►►
It can cause injury to human, problem to product and damage the
display.
•• Do not let the product fall or drop when connecting it with an
external device.
►►
This may cause injury and/or damage to the product.
•• When connecting it with a game device, keep a distance of four
times as long as the diagonal measurement of the screen from
the device.
►►
If the product falls because of the short cable, this may cause injury
and/or damage to the product.
►►
The product can be damaged.
ENGLISH
Safety precautions
3
4
SAFETY PRECAUTIONS
ENGLISH
Precautions to the AC adapter and
electrical power
WARNING
•• If water or any foreign substance goes inside the product (TV,
monitor, power cord, or AC adapter), disconnect the power cord
immediately and contact the service center.
►►
Otherwise, this may cause a fire or electric shock due to damage to
the product.
•• Do not touch the power plug or AC adapter with wet hands. If the
pins of the plug are wet or dusty, wipe and dry them before use.
►►
Otherwise, this may cause a fire or electric shock.
•• Make sure to completely insert the power cord into the AC adapter.
►►
If loosely connected, the poor connection may cause a fire or electric
shock.
•• Be sure to use power cords and AC adapters provided or approved
by LG Electronics, Inc.
►►
The use of non-approved products may cause a fire or electric shock.
•• When unplugging the power cord, always pull it by the plug. Do
not bend the power cord with excessive force.
►►
The power line can be damaged, which may cause electric shock
or fire.
•• Be careful not to step or place heavy objects (electronic appliances,
clothing, etc.) on the power cord or AC adapter. Be careful not to
damage the power cord or AC adapter with sharp objects.
►►
Damaged power cords may cause a fire or electric shock.
•• Never disassemble, repair or modify the power cord or AC adapter.
►►
This may cause a fire or electric shock.
•• Make sure to connect the power cable to the grounded current.
►►
You may be electrocuted or injured.
•• Use the rated voltage only.
►►
The product can be damaged, or you may be electrocuted.
•• In the presence of thunder and lightning, never touch the power
cord and signal cable because it can be very dangerous.
►►
It can cause electric shock.
•• Do not connect several extension cords, electrical appliances
or electrical heaters to a single outlet. Use a power bar with a
grounding terminal designed for exclusive use with the computer.
►►
A fire can break out due to overheating.
•• Do not touch the power plug with wet hands. Additionally, if
the cord pin is wet or covered with dust, dry the power plug
completely or wipe dust off.
►►
You may be electrocuted due to excess moisture.
•• If you don't intend to use the product for a long time, unplug the
power cable from the product.
►►
Covering dust can cause a fire, or insulation deterioration can cause
electric leakage, electric shock or fire.
•• Fix the power cable completely.
►►
If the power cable is not fixed completely, a fire can break out.
•• Do not insert a conductor (like a metal chopstick) into one end
of the power cable while the other end is connected to the input
terminal on the wall. Additionally, do not touch the power cable
right after plugging into the wall input terminal.
►►
You may be electrocuted.
•• The appliance coupler is used as the disconnect device.
•• Please make sure the device is installed near the wall outlet to
which it is connected and that the outlet is easily accessible.
•• As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if the unit is turned
off.
CAUTION
•• Be sure to keep the outlet, AC adapter, and pins of the power plug
clean from dust and etc.
►►
This may cause a fire.
•• Do not unplug the power cord while the product is in use.
►►
Electrical shock can damage the product.
•• Use only the power cord supplied with the unit. If you use another
power cord, make sure that it is certified by the applicable national
standards when not provided by the supplier. If the power cable is
faulty in any way, please contact the manufacturer or the nearest
authorized repair service provider for a replacement.
SAFETY PRECAUTIONS
WARNING
•• Make sure to turn off the product.
►►
You may be electrocuted or the product can be damaged.
•• Make sure to remove all cables before moving the product.
►►
You may be electrocuted or the product can be damaged.
•• Make sure the panel faces forward and hold it with both hands to
move. If you drop the product, the damaged product can cause
electric shock or fire. Contact an authorized the service center for
repair.
•• Make sure the product is turned off, unplugged and all cables
have been removed. It may take 2 or more people to carry larger
apparatus. Do not press against or put stress on the front panel of
the apparatus.
CAUTION
•• Do not shock the product when moving it.
•• Set the appropriate resolution and clock by referring to the User’s
Guide.
►►
Your vision can be impaired.
•• Use authorized detergent only when cleaning the product. (Do not
use benzene, thinner or alcohol.)
►►
Product can be deformed.
•• Do not expose to dripping or splashing and do not place objects
filled with liquids, such as vases, cups, etc. on or over the
apparatus (e.g. on shelves above the unit).
•• Batteries should not be exposed to excessive heat. For example,
keep away from direct sunlight, open fireplace and electric
heaters.
•• Do NOT place non-rechargeable batteries in charging device.
•• Using headsets (earphones) for a long time or listening loudly can
cause damage to your hearing.
•• Spray water onto a soft cloth 2 to 4 times, and use it to clean the
front frame; wipe in one direction only. Too much moisture may
cause staining.
►►
You may be electrocuted or the product can be damaged.
•• Do not dispose the product-packing box. Use it when you move.
Precautions in using the product
WARNING
•• Do not disassemble, repair or modify the product at your own
discretion.
►►
Fire or electric shock accident can occur.
►►
Contact the service center for check, calibration or repair.
•• When the display is to be left unattended for an extended period
of time, unplug it from the wall outlet.
•• Keep the product away from water.
►►
Fire or electric shock accident can occur.
•• Do not shock or scratch the front and sides of the screen with
metallic objects.
►►
Otherwise, it may cause damage to the screen.
•• Avoid high temperatures and humidity.
CAUTION
•• Do not put or store inflammable substances near the product.
►►
There is a danger of explosion or fire due to careless handling of the
inflammable substances.
•• When cleaning the product, unplug the power cord and scrub
gently with a soft cloth to prevent scratching. Do not clean with a
wet cloth or spray water or other liquids directly onto the product.
An electric shock may occur. (Do not use chemicals such as
benzene, paint thinners or alcohol)
•• Take a rest from time to time to protect your vision.
•• Keep the product clean at all times.
•• Take a comfortable and natural position when working with a
product to relax the muscles.
•• Take a regular break when working with a product for a long time.
•• Do not press strongly upon the panel with a hand or sharp object
such as nail, pencil or pen, or make a scratch on it.
•• Keep the proper distance from the product.
►►
Your vision may be impaired if you look at the product too closely.
•• Do not use products using high voltage around the Monitor.
(e.g., a bug zapper)
►►
Monitor may have malfunction as its electrical shock.
Mounting on a wall
•• Do NOT install this product by yourself as you may injure yourself
or cause damage to product. Please contact Service personnel
authorised by Manufacturer.
ENGLISH
Precautions in moving the product
5
6
LICENSES
ENGLISH
LICENSES
Supported licenses may differ by model. For more information of the licenses, visit www.lg.com.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
This DivX Certified® device has passed rigorous testing to ensure it plays DivX®
video.
To play purchased DivX movies, first register your device at vod.divx.com. Find your
registration code in the DivX VOD section of your device setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX, LLC and are
used under license.
Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274.
Manufactured under license from Dolby Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
ASSEMBLY AND PREPARATION
Accessories
Check your product box for the following items. If there are any missing accessories, contact the local dealer
where you purchased your product. The illustrations in this manual may differ from the actual product and
accessories.
Remote Control,
Batteries (AAA) 2 EA
Power Cord
D-sub 15-pin Signal
Cable
Card and the Letter of
Warranty
RS-232C Gender
IR Receiver
CAUTION
•• Always use genuine components to ensure safety and product performance.
•• The product warranty will not cover damage or injury caused by the use of counterfeit components.
NOTE
•• The accessories provided with your product may vary depending on the model or region.
•• Product specifications or contents in this manual may be changed without prior notice due to upgrade of
product functions.
•• SuperSign Software & Manual
- Downloading from the LG Electronics website.
- Visit the LG Electronics website (www.lgecommercial.com/supersign) and download the latest software
for your model.
ENGLISH
ASSEMBLY AND PREPARATION
7
8
ASSEMBLY AND PREPARATION
ENGLISH
Optional Accessories
Without prior notice, optional accessories are subject to change to improve the performance of the product,
and new accessories may be added. The illustrations in this manual may differ from the actual product and
accessories.
Screws
Stand
Spacers
Diameter 4.0 mm x Pitch 0.7 mm
Length
Model
Stand
ST-322T
32SE3*
ST-432T
ST-492T
ST-652T
43SE3*
49SE3*/55SE3*
65SE3*
32SE3*
43SE3*
49SE3*
55SE3*
65SE3*
-
32SE3*
43SE3*
49SE3*
55SE3*
65SE3*
2 EA
(including
spring washer)
Quantity
10 mm
14 mm
14 mm
14 mm
16 mm
6 EA
8 EA
8 EA
8 EA
8 EA
Stand kit
Speakers
SP-5000
Cable holder/
Cable Tie
Screws
Diameter 4.0 mm x Pitch
0.7 mm x Length 8 mm
(including spring washer)
Screws
Diameter 4.0 mm x Pitch
1.6 mm x Length 10 mm
Speaker kit
(Only for **SE3B model)
NOTE
•• Cable holder/cable tie may not be available in some areas or for some models.
•• Optional accessories are available for some models. If necessary, please purchase them separately.
ASSEMBLY AND PREPARATION
9
ENGLISH
Media Player
MP500/ MP700
Screws
CD (Owner's Manual)/
Cards
Media Player kit
( It may not be supported depending on the model.)
AN-WF500
Wi-Fi Dongle kit
NOTE
•• Optional accessories are available for some models. If necessary, please purchase them separately.
10
ASSEMBLY AND PREPARATION
- The image may be different according to the model
43SE3B
49SE3B
55SE3B
32SE3KB
43SE3KB
49SE3KB
55SE3KB
RGB IN
LAN
USB 1
USB 2
32SE3B
DVI-D IN
ENGLISH
Parts and Buttons
SPEAKER
OUT
RS-232C
IN
RS-232C
OUT
EXT IR
IN
AUDIO AUDIO
IN
OUT
Buttons
(Only for **SE3B model)
Buttons
Description
INPUT
Changes the input source.
MENU
Accesses the main menus, or saves your input and exits the menus.
Adjust the up and down.
Moves left and right.
AUTO/SET
/I
Displays the current signal and mode.
Turns the power on or off.
Connection
Panel
ASSEMBLY AND PREPARATION
ENGLISH
65SE3KB
DVI-D IN
RGB IN
LAN
USB 1
USB 2
65SE3B
11
SPEAKER
OUT
RS-232C
IN
RS-232C
OUT
EXT IR
IN
AUDIO AUDIO
IN
OUT
Buttons
(Only for **SE3B model)
Buttons
Description
INPUT
Changes the input source.
MENU
Accesses the main menus, or saves your input and exits the menus.
Adjust the up and down.
Moves left and right.
AUTO/SET
/I
Displays the current signal and mode.
Turns the power on or off.
Connection
Panel
12
ASSEMBLY AND PREPARATION
ENGLISH
Connecting the Stand
43SE3*
- For certain models only.
- The image may be different according to the
model
65SE3*
1
32SE3*
1
49SE3*
55SE3*
Place a soft cloth on the table and place the
product with the screen facing downward.
Place a soft cloth on the table and place the
product with the screen facing downward.
2Tighten stand spacers on the back of the
product as shown below.
2
Use the screws to secure the stand to the back
of the product as shown below.
3
Use the screws to secure the stand to the back
of the product as shown below.
ASSEMBLY AND PREPARATION
- For certain models only. (Only for **SE3B model)
- The image may be different according to the
model.
43SE3B
55SE3B
65SE3B
1
Connect an input signal cable before installing
the speakers.
32SE3B
1
49SE3B
Connect an input signal cable before installing
the speakers.
2
Mount the speakers by using screws as
shown below. Make sure the power cable is
disconnected before making a connection.
2
Mount the speakers by using screws as
shown below. Make sure the power cable is
disconnected before making a connection.
3
Then connect the speaker cable. After installing
your speakers, use holders and cable ties to
3
Then connect the speaker cable. After installing
your speakers, use holders and cable ties to
organize the speaker cables.
organize the speaker cables.
ENGLISH
Connecting the Speakers
13
14
ASSEMBLY AND PREPARATION
ENGLISH
NOTE
•• Please turn off the power before removing the
cable. Connecting or removing the speaker
cable while turned on may result in no sound.
Using the IR Receiver
- The image may be different according to the
model.
This allows a remote control sensor to be placed
in a custom location. Then that display can control
other displays via an RS-232C cable. Install the IR
receiver towards the front of the set.
IR Receiver cable
NOTE
•• When you see from the back of the set, if the
IR receiver cable does not face front, the signal
reception range may shorten.
•• The IR receiver is made with a magnet.It is
detachable at the bottom (typical installation)
or back (wall installation) of the set.
•• Make sure that you unplug the power cord
before connecting or removing the IR Receiver.
ASSEMBLY AND PREPARATION
When installing in a portrait layout, rotate the
monitor counterclockwise 90 degrees (when facing
the screen).
Using Kensington Lock
(This is not available for all models.)
The Kensington security system connector is
located at the back of the monitor. For more
information on installation and use of this system,
refer to the manual provided with the Kensington
security system or visit http://www.kensington.
com.
Connect the Kensington security system cable
between the monitor and a table.
NOTE
•• The Kensington security system is optional. You
can obtain additional accessories from most
electronics retail stores.
ENGLISH
Portrait Layout
15
16
ASSEMBLY AND PREPARATION
ENGLISH
Attaching and removing the LG Logo Bracket
- For certain models only.
- The image may be different according to the model.
Removing the LG Logo
1Lay a clean cloth on the floor, and then put the
monitor on it with the screen face down. Using
a screwdriver, remove the screw that secures
the LG Logo Bracket to the bottom rear of the
monitor.
Attaching the LG Logo on the right side
1Lay a clean cloth on the floor, and then put the
monitor on it with the screen face down. Using
a screwdriver, remove the screw that secures
the LG Logo Bracket to the bottom rear of the
monitor.
LG Logo Bracket
2
After removing the screw, remove the LG Logo.
When re-attaching the LG Logo, repeat the process
in reverse order.
2
After removing the screw, remove the LG Logo.
Attach the LG Logo Bracket with a screw, aligning it
with the hole on the right side.
ASSEMBLY AND PREPARATION
CAUTION
For proper ventilation, allow a clearance of 10
cm on each side and from the wall. Detailed
installation instructions are available from your
dealer, see the optional Tilt Wall Mounting Bracket
Installation and Setup Guide.
10 cm
10 cm
10 cm
10 cm
10 cm
•• Disconnect the power cord before moving or
installing the monitor to avoid risk of electric
shock.
•• If you install the monitor on a ceiling or slanted
wall, it may fall and result in injury. Use an
authorized LG wall mount and contact your
local dealer or qualified personnel to assist with
the installation.
•• Do not over tighten the screws as this may
damage the monitor and void your warranty.
•• Use only screws and wall mounting brackets
that meet the VESA standard. Any damage or
injuries caused by misuse or use of improper
accessories are not covered by the warranty.
•• To prevent injury, this apparatus must be
securely attached to the wall in accordance
with the installation instructions. (This pertains
only to Australia and New Zealand.)
To install your monitor on a wall, attach a wall
mounting bracket (optional part) to the back of the
monitor.
Make sure that the wall mounting bracket is
securely fixed to the monitor and to the wall.
1
Use only screws and wall mounting brackets
that conform to VESA standards.
2Screws which are longer than standard length
may damage the inside of the monitor.
3
A non-VESA standard screw may damage
the product and cause the monitor to fall. LG
Electronics is not liable for any accidents related
to the use of non-standard screws.
4
Please use VESA standard as below.
•• 785 mm and above
* Fixing screws: Diameter 6.0 mm x Pitch
1.0 mm x Length 12 mm
785 mm
NOTE
•• The wall mount kit includes the installation
guide and all necessary parts.
•• The wall mounting bracket is optional. You can
obtain additional accessories from your local
dealer.
•• The length of screws required may differ
depending on the wall mount. Be sure to use
the correct length.
•• For more information, please refer to the guide
provided with the wall mount.
•• The warranty will not cover any damages
caused by using the product in an excessively
dusty environment.
ENGLISH
Installing on a Wall
17
18
ASSEMBLY AND PREPARATION
ENGLISH
Securing the monitor to a wall (optional)
Procedure may differ depending on the model.
1
Insert and tighten the eyebolts, or brackets and
bolts on the back of the monitor.
- If there are already bolts inserted in the
eyebolts’ position, remove the other bolts first.
2
Mount the wall brackets with the bolts to the
wall. Match the location of the wall bracket and
the eyebolts on the rear of the monitor.
3
Connect the eyebolts and wall brackets tightly
with a sturdy cord.
Make sure the securing cord is horizontal with
the flat surface.
CAUTION
•• Make sure that children do not climb on or
hang from the monitor.
NOTE
•• Use a platform or cabinet that is large and
strong enough to support the monitor securely.
•• Brackets, bolts, and cords are sold separately.
You can obtain additional accessories from your
local retail store.
•• The illustration shows a general example of
installation and may look different from the
actual product.
WARNING
•• If the monitor is not positioned in a
sufficiently stable location, there is a danger
that it will fall. Many injuries, particularly to
children, can be avoided by taking simple
precautions such as:
»»Using cabinets or stands recommended
by the manufacturer.
»»Only using furniture that can safely
support the monitor.
»»Ensuring the monitor is not overhanging
the edge of the supporting furniture.
»»Not placing the monitor on tall furniture
(for example, cupboards or bookcases)
without anchoring both the furniture and
the monitor to a suitable support.
»»Not placing cloth or other materials
between the monitor and supporting
furniture.
»»Educating children about the dangers
of climbing on furniture to reach the
monitor or its controls.
REMOTE CONTROL
19
The descriptions in this manual are based on the buttons on the remote control. Please read this manual
carefully to use the monitor correctly.
To install batteries, open the battery cover, place batteries (1.5 V AAA) matching
labels inside the compartment, and close the battery cover.
and
terminals to the
To remove the batteries, perform the installation actions in reverse. The illustrations may differ from the actual
accessories.
CAUTION
•• Do not mix old and new batteries, as this may
damage the remote control.
•• Be sure to point the remote control toward the
remote control sensor on the monitor.
(POWER) Turns the monitor on or off.
MONITOR ON Turns the monitor on.
MONITOR OFF Turns the monitor off.
ENERGY SAVING( ) A
djusts the brightness of the picture to reduce
energy consumption.
INPUT Selects the input mode.
3D Used for viewing 3D videos. (This model does not support this.)
1/a/A Toggles between numerical and alphabetical.
(Depending upon the model, this feature may not be supported.)
Number and Alphabet buttons Enters numerical or alphabetical characters depending upon the setting.
(Depending upon the model, this feature may not be supported.)
CLEAR Deletes the entered numerical or alphabetical character.
(Depending upon the model, this feature may not be supported.)
Volume Up/Down Button Adjusts the volume.
ARC Selects the Aspect Ratio mode.
AUTO Automatically adjusts picture position and minimizes image
instability (available for RGB input only). (Depending upon the
model, this feature may not be supported.)
MUTE Mutes all sounds.
BRIGHTNESS Adjust the brightness by pressing the Up and Down
buttons on the remote control. In USB mode, the OSD
menu has the Page function to move to the next file list.
(Depending upon the model, this feature may not be
supported.)
BACK
TILE
ID
ON
OFF
EXIT
ENGLISH
REMOTE CONTROL
20
REMOTE CONTROL
ENGLISH
PSM Selects the Picture Mode.
INFO Views the information of the currently program and the screen.
W.BAL Enters the White Balance menu.
SETTINGS A
ccesses the main menus or saves your input and exit menus.
S.MENU S uperSign menu key (Depending upon the model, this feature
may not be supported.)
Navigation Buttons Scrolls through menus or options.
OK Selects menus or options and confirms your input.
BACK A
llows you to move back one step in the user interaction function.
EXIT Quit all OSD tasks and applications.
A
llows you to control various multimedia devices to enjoy
multimedia simply by using the remote control through the
SimpLink menu. (Depending upon the model, this feature
may not be supported.)
TILE Selects the TILE Mode.
PICTURE ID ON/OFF W
hen the Picture ID number matches the Set ID
number, you can control whichever monitor you
want in multi-display format.
USB Menu Control Buttons Controls media playback.
REMOTE CONTROL
Display which devices are connected to which
external input ports.
1
Access the Input list screen and press the red
(input label) button on the remote control.
2
You can assign an input label for every input
except USB.
NOTE
•• External inputs supported : HDMI, DVI-D
•• Labels available : PC, DTV
•• The input labels are displayed on the Input Label
screen or at the top left of the screen when you
change the external input setting.
•• For DTV/PC-compatible signals, such as
1080p 60 Hz, the screen settings may change
according to the input label. The Just Scan
option is available if a PC is connected as an
external device.
White Balance Adjust Menu
Press the W.BAL button on the remote control.
djusts the level of red. The higher
yyR-Gain : A
the number, the redder the set.
Decrease the number if the screen
looks too red.
djusts the level of green. The
yyG-Gain : A
higher the number, the greener
the set. Decrease the number if the
screen looks too green.
djusts the level of blue. The higher
yyB-Gain : A
the number, the bluer the set.
Decrease the number if the screen
looks too blue.
djusts the brightness. The
yyBacklight : A
higher the number, the brighter
the set. This works in the same
way as the backlight of the user
menu.
esets the white balance value to
yyReset : R
the factory settings.
ENGLISH
Displaying the Device Name
Connected to an Input Port
21
22
REMOTE CONTROL
ENGLISH
Using Picture ID
NOTE
Picture ID is used to change the settings of a
specific display using a single IR receiver for
multi-vision. The set receiving the IR signal
communicates with another set via an RS-232C
connection. Each set is identified by a Set ID. If you
assign the Picture ID using the remote control, only
displays with the same Picture ID and Set ID can be
controlled remotely.
AUDIO
(RGB/DVI)
RS-232C OUT
RS-232C OUT
RS-232C OUT
RS-232C IN
RS-232C IN
RS-232C IN
REMOTE
CONTROL IN
IR Receiver
RS-232C
Picture ID
Off
Close
2X2 Multi-Vision
Set IDs are assigned as shown in the picture.
1Press the red ON button on the remote control
to assign the Picture ID.
2
To change the Picture ID, press the ON
button, or the left and right arrow buttons
continuously. Assign the ID you want.
•• If you assign the Set ID to each set with multivision, and then assign the Picture ID using
the red button on the remote control, the key
command is displayed for the set with the same
Set ID and Picture ID. A set with different Set
IDs and Picture IDs cannot be controlled by IR
signals.
•• For example, if the Picture ID is assigned to
2, the upper right display (Set ID: 2) can be
controlled by IR signals.
•• For each set, you can change the settings for
the PICTURE, AUDIO, TIME, NETWORK and MY
MEDIA menus or the hot keys on the remote
control.
•• If you press the green OFF button for Picture IDs,
the Picture IDs for all sets are turned off. If you
then press any button on the remote control, all
sets will start working again.
•• Picture ID will be disabled while using the MY
MEDIA menu.
USB 1
LAN
You can connect various external devices to your monitor. Change the input mode and select the external
device you want to connect.
USB 2RGB IN
For more information about external device connections, see the user manual provided with each device.
Connecting to a PC
The illustrations may differ from the actual accessories. Some of the cables are not provided.
This monitor supports the Plug & Play* feature.
* Plug & Play: a feature that enables a PC to recognize devices attached by the user without device
configuration or user intervention when powering up.
RGB OUT
49SE3*
55SE3*
LAN
43SE3*
DVI-D
IN 1
USB
AUDIO OUT
32SE3*
RS-232C
IN
SPEAKER
OUT
RS-232C
OUT
EXT IR
IN
AUDIO AUDIO
IN
OUT
(not included)
RGB IN
Mac
RGB OUT
DVI-D IN
HDMI OUT AUDIO OUT
AUDIO OUT
DVI OUT
(not included)
SPEAKER
OUT
RS-232C
IN
RS-232C
OUT
EXT IR
IN
AUDIO AUDIO
IN
OUT
(not included)
(Only for **SE3B model)
HDMI OUT
(not included)
AUDIO OUT
(not included)
DVI OUT
23
ENGLISH
MAKING CONNECTIONS
MAKING CONNECTIONS
USB
MAKING CONNECTIONS
AUDIO OUT
RGB OUT
65SE3*
RS-232C
IN
RS-232C
OUT
EXT IR
IN
AUDIO AUDIO
IN
OUT
LAN
SPEAKER
OUT
(not included)
(not included)
HDMI OUT
AUDIO OUT
Mac
DVI OUT
AUDIO OUT
HDMI OUT
RGB IN
(not included)
DVI OUT
RGB OUT
DVI-D IN
ENGLISH
DVI-D
USB
1 IN
24
(not included)
(not included)
SPEAKER
OUT
RS-232C
IN
RS-232C
OUT
EXT IR
IN
AUDIO AUDIO
IN
OUT
(Only for **SE3B model)
AUDIO OUT
DVI OUT
MAKING CONNECTIONS
25
Connect a HD receiver, DVD, or VCR player to the monitor and select an appropriate input mode.
The illustrations may differ from the actual accessories. Some of the cables are not provided. For the best
picture and sound quality, connecting external devices to your monitor using HDMI cables is recommended.
43SE3*
49SE3*
55SE3*
USB 2
32SE3*
OR
03
USB 1
USB
(not included)
LAN
(not included)
RGB IN
Direct Connection/
Using the Router/
Using the Internet
HDMI OUT
HD Receiver/DVD/VCR
DVI-D IN
Camcorder/Camera/Gaming Device
Network
SPEAKER
OUT
RS-232C
IN
RS-232C
OUT
EXT IR
IN
AUDIO AUDIO
IN
OUT
AV Receiver
(Only for **SE3B model)
(not included)
ENGLISH
External Device Connection
26
MAKING CONNECTIONS
USB 2
OR
03
USB 1
USB
LAN
(not included)
(not included)
RGB IN
HDMI OUT
Network
HD Receiver/DVD/VCR
Camcorder/Camera/Gaming Device
SPEAKER
OUT
RS-232C
IN
RS-232C
OUT
Direct Connection/
Using the Router/
Using the Internet
DVI-D IN
ENGLISH
65SE3*
EXT IR
IN
AUDIO AUDIO
IN
OUT
(Only for **SE3B model)
AV Receiver
(not included)
MAKING CONNECTIONS
27
•• Use the standard Macintosh adapter since an incompatible adapter is available in the
market. (Different signaling system)
•• Apple computers may require an adapter to connect to this monitor. Call or visit their
web site for more information.
CAUTION
•• Connect the signal input cable and tighten it by turning the screws clockwise.
•• Do not press the screen with your finger for a long time as this may result in
temporary distortion on the screen.
•• Avoid displaying a fixed image on the screen for a long period of time to prevent
image burn. Use a screensaver if possible.
•• If using a DP to HDMI dongle, make sure to use a dongle certified by the graphics card manufacturer.
•• When connecting to multi-channel ports of a graphics card, make sure to use DP to HDMI dongles of the
same model.
ENGLISH
NOTE
•• The monitor set with the HDMI connection for the best image quality.
•• To comply with the specifications of the product, use a shielded interface cable with ferrite core, such as a
D-sub 15-pin cable and DVI/HDMI cable.
•• If you turn the monitor set on when the set becomes cold, the screen may flicker. This is normal.
•• Some red, green, or blue spots may appear on the screen. This is normal.
•• To minimize the impact of electromagnetic waves, secure the cables with cable ties.
•• Use a High Speed HDMI®/™ Cable.
•• If you want to use HDMI-PC mode, you must set the input label to PC mode.
•• When HDMI PC is used, a compatiblity problem could occur.
•• Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may
not display or a connection error may occur.
•• Recommended HDMI cable types
-High-Speed HDMI®/™ Cable
-High-Speed HDMI®/™ Cable with Ethernet
28
USING THE MONITOR
ENGLISH
USING THE MONITOR
Using the Input List
1
Press INPUT to access the Input List.
2
Press the navigation buttons to scroll to one of the input mode and press OK.
yyRGB : View a PC display on the screen.
atch contents in a PC, DVD of digital set-top box other high definition devices.
yyHDMI : W
yyDVI-D : Displays multimedia contents on your PC, DVD and other HD devices.
yyUSB : Plays the multimedia file saved in the USB.
Adjusting Aspect Ratio
Resize the image to view the image at its optimal size by pressing ARC while you are watching monitor set.
MODE
RGB
DVI-D
HDMI
PC
DTV
PC
16:9
o
o
Just Scan
x
o
Set By Program
x
4:3
Zoom
Cinema Zoom
Aspect Ratio
DTV
PC
o
o
o
x
o
x
o
x
o
x
o
o
o
o
o
x
o
x
o
x
x
o
x
o
x
NOTE
•• You can also change the image size by accessing the main menus.
•• The Just Scan mode operates when a video signal has resolution of 720p or higher.
CAUTION
•• If a fixed image displays on the screen for a long period of time, it will be imprinted and become a
permanent disfigurement on the screen. This is image burn or burn-in and not covered by the warranty.
•• If you don't use your monitor, turn the power off or set a screen saver program from the PC or the system to
prevent image retention.
•• If the aspect ratio is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the
screen.
USING THE MONITOR
29
screen. However, the top and bottom of the picture will be cropped.
yyCinema Zoom Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note:
When enlarging or reducing the picture, the image may become distorted.
ENGLISH
yy16:9 T his selection will allow you to adjust the picture horizontally, in linear proportion, to fill the entire
screen (useful for viewing 4:3 formatted DVDs).
yyJust Scan This Selection will allow you view the picture of best quality without loss of original picture
in high resolution image. Note: If there is noise in original Picture, You can see the noise at the
edge.
yySet By Program Depending on the input signal, screen aspect ratio changes to 4:3 or 16:9.
yy4:3 T his selection will allow you to view a picture with an original 4:3 aspect ratio, black bars will appear
on both the left and right of the screen.
yyZoom This selection will allow you to view the picture without any alteration, while filling the entire
30
ENTERTAINMENT
ENGLISH
ENTERTAINMENT
Using the Network
To set up the network settings: (Even if your display
has already connected automatically, running
setup again will not harm anything),
Connecting to a wired network
Connecting to a Network
For wired network connections, connect the
display to a local area network (LAN) via the LAN
port as shown on the following diagram. Then, set
up the network settings. For wireless network connections, connect the Wi-Fi USB module to the USB
port. Then, set up the network settings.
After making a physical connection, a small
number of home networks may require the display
network settings to be adjusted. For most home
networks, the display will connect to automatically
without any adjustments.
For detail information, contact your internet provider or router manual.
1
Press SETTINGS to access the main menus.
2
Press the navigation buttons to scroll to NETWORK and press OK.
3
Press the navigation buttons to select Network Setting and press OK.
4
If you already set network setting, select
Resetting. The new connection settings resets
the current network settings.
5Select IP Auto Setting or IP Manual Setting.
-IP Manual Setting
press the navigation and number buttons. IP
addresses will need to be input manually.
- IP Auto Setting
Select this if there is a DHCP server (Router)
on the local area network (LAN) via wired
connection, the display will automatically
be allocated an IP address. If you’re using a
broadband router or broadband modem that
has a DHCP (Dynamic Host Configuration
Protocol) server function. The IP address will
automatically be determined.
LAN
Router
@
Internet
Internet
LAN
WAN
6
ETHERNET
Cable modem
CAUTION
•• Do not connect a modular phone cable to the
LAN port.
•• Since there are various connection methods,
please follow the specifications of your
telecommunication carrier or internet service
provider.
When you are finished, press EXIT.
ENTERTAINMENT
Connecting to a wireless network
2
Press the navigation buttons to scroll to NETWORK and press OK.
3
Press the navigation buttons to select Network Setting and press OK.
4
Select Setting from the AP list or Simple
setting (WPS-button mode).
-Setting from the AP list
Select an AP to connect to a wireless network.
-Simple setting (WPS-button mode)
Press the button on the wireless router that
supports PBC to easily connect to the router.
5
When you are finished, press EXIT.
CAUTION
•• Network setting menu will not be available until
the display connected to physical network.
•• Since there are various connection methods,
please follow the specifications of your
telecommunication carrier or internet service
provider.
NOTE
•• If you want to access the Internet directly on
your display, the Internet connection should
always be on.
•• If you cannot access the Internet, check the
network conditions from a PC on your network.
•• When you use Network Setting, check the LAN
cable or check if DHCP in the router is turned on.
•• If you do not complete the network settings, the
network may not work properly.
Tips for Network setting
yyUse a standard LAN cable with this display. Cat5 or
better with a RJ45 connector.
yyMany network connection problems during set
up can often be fixed by re-setting the router or
modem. After connecting the display to the home
network, quickly power off and/or disconnect the
power cable of the home network router or cable
modem. Then power on and/or connect the power
cable again.
yyDepending on the internet service provider (ISP),
the number of devices that can receive internet
service may be limited by the applicable terms of
service. For details, contact your ISP.
yyLG is not responsible for any malfunction of the
display and/or the internet connection feature due
to communication errors/malfunctions associated
with your internet connection, or other connected
equipment.
yyLG is not responsible for problems within your
internet connection.
yyYou may experience undesired results if the network connection speed does not meet the requirements of the content being accessed.
yySome internet connection operations may not be
possible due to certain restrictions set by the Internet service provider (ISP) supplying your Internet
connection.
yyAny fees charged by an ISP including, without limitation, connection charges are your respon- sibility.
yyA 10 Base-T or 100 Base-TX LAN port is required
when using a wired connection to this display. If
your internet service does not allow for such a connection, you will not be able to connect the display.
yyA DSL modem is required to use DSL service and
a cable modem is required to use cable modem
service. Depending on the access method of and
subscriber agreement with your ISP, you may not
be able to use the Internet connection feature contained in this display or you may be limited to the
number of devices you can connect at the same
time. (If your ISP limits subscription to one device,
this display may not be allowed to connect when a
PC is already connected.)
yyThe use of a router may not be allowed or its usage
may be limited depending on the policies and
restrictions of your ISP. For details, contact your ISP
directly.
ENGLISH
1Press SETTINGS to access the main menus.
31
32
ENTERTAINMENT
Tips for Wireless Network Setting
ENGLISH
yyWireless networks can be subject to interference from other devices operating at a frequency of 2.4 GHz (wireless phones, Bluetooth
devices, or microwave ovens). There may also
be interference from devices with a frequency
of 5 GHz, same as other Wi-Fi devices.
yyThe surrounding wireless environment can
cause the wireless network service to run
slowly.
yyFor an AP connection, an access point device
that supports wireless connection is required
and the wireless connection feature must be
enabled on the device. Contact your service
provider regarding availability of wireless connection on your access point.
yyCheck the SSID and security settings of the AP
for AP connection. Refer to the appropriate
documentation for SSID and security settings
of the AP.
yyInvalid settings on network devices (wired/
wireless line sharer, hub) can cause the
monitor to run slowly or not operate properly.
Install the devices correctly according to the
appropriate manual and set the network.
yyConnection method may differ according to
the AP manufacturer.
Using the My Media
Connecting USB storage devices
Connect USB storage devices such as a USB flash
memory, external hard drive to the display and use
multimedia features.
Connect a USB flash memory or USB memory card
reader to the Display as shown on the following
illustration. The My Media screen appears.
or
Network Status
1
Press SETTINGS to access the main menus.
2
Press the navigation buttons to scroll to
NETWORK and press OK.
3
Press the navigation buttons to select
Network Status.
4Press OK to check the network status.
5 When you are finished, press EXIT.
Option
Setting
Test
Close
Description
Return to the network setting menu.
Test the current network status after
setting the network.
Return to the previous menu.
CAUTION
•• Do not turn the display off or remove a USB
storage device while MY MEDIA menu is
activated, as this could result in loss of files or
damage to the USB storage device.
•• Back up your files saved on a USB storage device
frequently, as you may lose or damage the files
and this may be not covered by the warranty.
ENTERTAINMENT
Tips for using USB storage devices
yyIf your USB memory device has multiple partitions, or if you use a USB multi-card reader,
you can use up to 4 partitions or USB memory
devices.
yyIf a USB memory device is connected to a USB
multi-card reader, its volume data may not be
detected.
yyIf the USB memory device does not work properly, disconnect and reconnect it.
yyHow fast a USB memory device is detected
differs from device to device.
yyIf the USB is connected in Standby Mode, that
drive will automatically be loaded when the
display is turned on.
yyThe recommended capacity is 1 TB or less for
a USB external hard disk and 32 GB or less for
USB memory.
yyAny device with more than the recommended
capacity may not work properly.
yyIf a USB external hard disk with a Energy Saving function does not work, turn the hard disk
off and on again to make it work properly.
yyUSB storage devices below USB 2.0 are supported as well. But they may not work properly
with videos.
yyA maximum of 999 folders or files can be
recognized under one folder.
yyIt is recommended you use a certified USB
storage device and cable. Otherwise, a USB
storage device may not be detected or a playback error may occur.
yyOnly a USB memory device can be used to play
back the files distributed and stored by SuperSign Manager. A USB hard disk or multi-card
reader will not work.
yyOnly an FAT 32 file formatted storage device
can play back the files distributed and stored
by SuperSign manager.
yyA USB 3.0 storage device may not work.
yyData on some USB storage devices may be
damaged in a high temperature environment.
yyIt is recommended that you avoid playing
contents using more than two USB ports
simultaneously.
ENGLISH
yyOnly a USB storage device is recognizable.
yyIf the USB storage device is connected through
a USB hub, the device is not recognizable.
yyA USB storage device using an automatic recognition program may not be recognized.
yyA USB storage device which uses its own driver
will not be recognized.
yyThe recognition speed of a USB storage device
may depend on each device.
yyPlease do not turn off the display or unplug
the USB device when the connected USB storage device is working. When such a device is
suddenly separated or unplugged, the stored
files or the USB storage device may be damaged.
yyPlease do not connect the USB storage device
which was artificially maneuvered on the PC.
The device may cause the product to malfunction. Only use a USB storage device which has
normal music files, image files
or movie files.
yyPlease only use USB storage devices formatted
using the FAT32 file system. Storage devices
formatted with utility programs that are not
supported by Windows may not be recognized.
yyPlease connect power to a USB storage device
(over 0.5 A) which requires an external power
supply. If not, the device may not be recognized.
yyPlease connect a USB storage device with the
cable included by the device maker.
yySome USB storage devices may not be supported or operate smoothly.
yyFile alignment method of USB storage devices
is similar to Window XP and the monitor can
recognize up to 100 English characters.
yyBe sure to back up important files since data
stored on a USB memory device may be damaged. We will not be responsible for any data
loss.
yyIf the USB HDD does not have an external
power source, the USB device may not be
detected. So be sure to connect the external
power source.
- Please use a power adaptor for an external
power source.
33
34
ENTERTAINMENT
ENGLISH
Browsing Files
Browse files saved in a USB storage device.
1
Press SETTINGS to access the main menu.
2
Press the search button to scroll to MY MEDIA and press OK.
3
Press the Search button to go to the Movie List, Photo List, Music List, or Content List that you want, and
press OK.
Supported file format
Type
Supported file format
Movie
Video
Codec
Media Container
Profile
MPEG1 / MPEG2
DAT, MPG, MPEG, TS, TP
1080P @ 30 fps
MPEG4
AVI, DIVX, MP4, MKV, TS,
1080P @ 30 fps
(DivX 3.11, DivX 4,
TRP
DivX 5, DivX 6,
Xvid 1.01, Xvid 1.02, Xvid
1.03, Xvid 1.10-beta1/2)
H.264
AVI, MP4, MKV, TS, TRP,
1080P @ 60 fps
TP
Audio
MP3
MP3
8 kbps to 320 kbps (Bit rate)
16 kHz to 48 kHz (Sample rate)
AC3
AC3
32 kbps to 640 kbps (Bit rate)
32 kHz, 44.1 kHz, 48 kHz
(Sample rate)
MPEG
MP3
32 kbps to 448 kbps (Bit rate)
AAC, HEAAC
MP4
8 kHz to 48 kHz (Sample rate)
LPCM
AVI, WAV
64 kbps to 1.5 Mbps (Bit rate)
16 kHz to 48 kHz (Sample rate)
8 kHz to 48 kHz (Sample rate)
Bit rate : within 8 kbps to 320 kbps(MP3)
External Subtitle format : *.smi/*.srt/*.sub(MicroDVD, Subviewer1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/*.
psb(PowerDivX)
Internal Subtitle format : only, XSUB (It is the subtitle format used in DivX6 files)
ENTERTAINMENT
Photo
Supported file format
JPEG
Baseline : 64 x 64 to 15360 x 8640
Progressive : 1024 x 768
PNG
Interlace : 1200 x 800
BMP
9600 x 6400
yyNon-supported files are displayed in the form of predefined icon.
Music
MP3
Bit rate : 8 kbps to 320 kbps
yySampling rate MPEG1/2 Layer3 : 16 kHz to 48 kHz
Content
File Extensions : *.cts/ *.cse
(when using
Movie
SuperSign
File Extensions: *.mpg/*.mpeg/*.dat/*.ts/*.trp/*.tp/*.mp4/*.mkv/*.avi/*. avi(motion JPEG)/*.mp4(motion
Manager)
JPEG)/*.mkv(motion JPEG)
Video format: MPEG1, MPEG2, MPEG4,H.264, DivX 3.11, DivX 4, DivX 5, DivX 6,
Xvid 1.00,Xvid 1.01, Xvid 1.02, Xvid 1.03,Xvid 1.10-beta1/2, JPEG
Audio format: MP3, Dolby Digital, LPCM, AAC, HE-AAC
ENGLISH
Type
35
36
ENTERTAINMENT
ENGLISH
Viewing Movies
Plays movie files saved in the USB storage device.
1
Press SETTINGS to access the main menu.
2
Press the navigation button to scroll to MY MEDIA and press OK.
3
Press the navigation button to scroll to Movie List and press OK.
4
Press the navigation buttons to scroll to a folder you want and press OK.
5
Press the navigation buttons to scroll to a file you want and press OK.
yyChange Device : Selects the USB storage device.
yyGo to root folder : Returns to the home screen of My Media.
yyGo to upper folder : Returns to the previous screen.
yyExit : Exits My Media.
6
During movie playback, press OK to access the following settings.
Remote
button
Description
Stops the playback.
Plays a video.
Pauses or resumes the playback.
Scans backward in a file.
Scans forward in a file.
Adjusts the screen brightness to save energy.
SETTINGS
BACK
EXIT
or
Show the Option menu.
Hide the menu on the full-sized screen.
Returns to Movie List.
Skips to specific points in a file during playback. The time of a specific point will appear on
the status bar. In some files, this function may not work properly.
ENTERTAINMENT
37
Tips for using playing video files
Video options
1
Press SETTINGS to access the Pop-Up menus.
2
Press the navigation buttons to scroll to Set Video Play, Set Video, or Set Audio, and press OK.
NOTE
yyThe option values changed in Movie List do not affect Photo List or Music List.Therefore, they are not
affected by option values changed in Photo List or Music List.
yyThe option values changed in Photo List and Music List do affect each other.
yyWhen replaying the video file after stopping, you can play from where it stopped previously.
ENGLISH
yySome user-created subtitles may not work properly.
yySome special characters are not supported in subtitles.
yyHTML tags are not supported in subtitles.
yySubtitles in languages other than the supported languages are not available.
yyThe screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the audio
language is changed.
yyA damaged movie file may not be played correctly, or some player functions may not be usable.
yyMovie files produced with some encoders may not be played correctly.
yyIf the video and audio structure of recorded file is not interleaved, either video or audio is outputted.
yyHD videos with a maximum of 1920 X 1080 @ 25/30P or 1280 X 720 @ 50/60P are supported, depending
on the frame.
yyVideos with resolutions higher than 1920 X 1080 @ 25/30P or 1280 X 720 @ 50/60P may not work properly depending on the frame.
yyMovie files other than the specified types and formats may not work properly.
yyMax bitrate of playable movie file is 20 Mbps. (only, Motion JPEG : 10 Mbps)
yyWe do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/AVC.
yyDTS Audio codec is not supported.
yyA movie file more than 30 GB in file size is not supported for playback.
yyA DivX movie file and its subtitle file must be located in the same folder.
yyA video file name and its subtitle file name must be identical for it to be displayed.
yyPlaying a video via a USB connection that doesn’t support high speed may not work properly.
yyFiles encoded with GMC(Global Motion Compensation) may not be played.
38
ENTERTAINMENT
Select Set Video Play to access the following menus:
ENGLISH
Menu
Picture Size
Audio
Language
Subtitle
Language
Language
Code Page
Sync
Position
Size
Repeat
Description
Selects your desired picture format during movie play.
Changes the Language Group of the audio during movie play. Files with a single audio
track cannot be selected.
Turn on/off the subtitle.
Activated for SMI subtitle and can select the language within the subtitle.
Can select the font for subtitle.
When set to default, same font as general menu will be used.
Adjusts the time synchronisation of the subtitle from -10 secs to +10 secs by steps of
0.5 secs during movie play.
Changes the position of the subtitle either up or down during movie play.
Selects your desired Subtitle size during movie play.
Turn on/off repeat function of movie playback. When turned on, the file within the
folder will be played back repeatedly. Even when the repeated playback is turned off, it
can run the playback if the file name is similar to the previous file.
NOTE
yyOnly 10,000 of sync blocks can be supported within the subtitle file.
yyWhen playing a video, you can adjust the picture size by pressing the ARC button.
yySubtitles in your language are only supported when the OSD menu is also in this language.
yyThe code page options may be disabled depending on the language of the subtitle files.
yySelect the appropriate code page for the subtitle files.
ENTERTAINMENT
39
View image files saved in the USB storage device.
1 Press SETTINGS to access the main menu.
2
Press the navigation button to scroll to MY MEDIA and press OK.
3
Press the navigation button to scroll to Photo List and press OK.
4
Press the navigation buttons to scroll to a folder you want and press OK.
5
Press the navigation buttons to scroll to a file you want and press OK.
yyChange Device : Selects the USB storage device.
yyGo to root folder : Returns to the home screen of My Media.
yyGo to upper folder : Returns to the previous screen.
yyExit : Exits My Media.
6While viewing photos, you can access the following settings.
Menu
Slideshow
BGM
Description
Starts or stops a slideshow with selected photos. If there are no selected photos, all photos
saved in the current folder display during a slideshow. To set a slideshow speed, select Option.
Turns the background music on or off. To set the background music folder, select Option.
You can adjust option by SETTINGS button on the remote control.
Rotates photos clockwise (90 °, 180 °, 270 °, 360 °).
NOTE
yyThe supported photo size is limited. You cannot rotate a photo if the resolution of the rotated
width is larger than the supported resolution size.
Enlarges the photo by 100 %, 200 % or 400 %.
NOTE
yyPhotos with a resolution of 100 x 100 or less cannot be enlarged.
Adjusts the brightness of the screen for energy saving.
Option
Hide
Exit
To display the OPTIONs.
Hides the option window. To display the options, press OK.
Return to Photo List.
ENGLISH
Viewing Photos
40
ENTERTAINMENT
Photo options
ENGLISH
1
Press SETTINGS to show the Option menus.
2
Press the navigation buttons to scroll to Set Photo View, Set Video, or Set Audio, and press OK.
NOTE
yyThe option values changed in Movie List do not affect Photo List or Music List.Therefore, they are not
affected by option values changed in Photo List or Music List.
yyThe option values changed in Photo List and Music List do affect each other.
Select Setting Photo View to access the following menus:
Menu
Slide Speed
BGM
Repeat
Random
Description
Select a slideshow speed.
(Options: Fast, Medium, or Slow.)
Selects a music folder for the background music.
Plays background music on repeat.
Plays background music in random order.
ENTERTAINMENT
Plays music files saved in the USB storage device.
1
Press SETTINGS to access the main menu.
2
Press the navigation button to scroll to MY MEDIA and press OK.
3
Press the navigation button to scroll to Music List and press OK.
4
Press the navigation buttons to scroll to a folder you want and press OK.
5
Press the navigation buttons to scroll to a file you want and press OK.
yyChange Device : Selects the USB storage device.
yyGo to root folder : Returns to the home screen of My Media.
yyOpen Music Player : Opens the settings window for music. This feature is activated only during playback.
yyGo to upper folder : Returns to the previous screen.
yyExit : Exits My Media.
6
During music playback, press OK or the blue button (
Remote
button
) to access the following settings.
Description
Stops playing back the file and moves back to the Music List.
Plays a music file.
Pauses or resumes playback.
Skips to the previous file.
Skips to the next file.
Adjusts the brightness of the screen for energy saving (Off and Screen Off work only.)
SETTINGS
BACK
EXIT
or
Show the Option menu.
Hides the option window.
To display the options, press OK.
Return to Music List.
Skips to specific points in a file during playback. The time of a specific point will appear on
the status bar. In some files, this function may not work properly.
ENGLISH
Listening to Music
41
42
ENTERTAINMENT
Tips for playing music files
ENGLISH
yyThis unit cannot support the ID3 Tag embedded MP3 files.
NOTE
yyA damaged or corrupted music file does not play but displays 00:00 in playtime.
yyA music downloaded from a paid service with copyright protection does not start but displays inappropriate information in playtime.
yyIf you press OK,
buttons, screen saver is stopped.
yyThe
,
,
,
,
buttons on the remote control are also available in this mode.
yyYou can use the
button to select the next music and the
button to select the previous music.
file name
002. B02.mp3
00:31 / 04:04
Time elapsed/ Duration
Music options
1
Press SETTINGS to access the pop-up menus.
2
Press the navigation buttons to scroll to Set Audio Play or Set Audio and press OK.
NOTE
yyThe option values changed in Movie List do not affect Photo List or Music List.Therefore, they are not
affected by option values changed in Photo List or Music List.
yyThe option values changed in Photo List and Music List do affect each other.
When you select the Set Audio Play,
Menu
Repeat
Random
Description
Repeats the music playback.
Plays random music tracks.
ENTERTAINMENT
43
Plays back the stored files using the Export option in SuperSign Manager.
1 Press SETTINGS to access the main menu.
2
Press the navigation button to scroll to MY MEDIA and press OK.
3
Press the navigation button to scroll to Contents List and press OK.
4
Press the navigation buttons to scroll to a folder you want and press OK.
5
Press the navigation buttons to scroll to a file you want and press OK.
yyChange Device : Selects the USB storage device.
yyGo to root folder : Returns to the home screen of My Media.
yyGo to upper folder : Returns to the previous screen.
yyExit : Exits My Media.
NOTE
yyWhile playing media files from Contents List, only the BACK, EXIT, or volume button are available.
Selecting the BACK or EXIT button stops playing media files and returns to the Contents List.
yyWhen you use the distribution feature which utilizes SuperSign Software, the storage device used to
store contents is determined based on the size of the remaining memory space. (Note: If USB ports 1
and 2 have the same memory space, contents will be saved on the storage device connected to USB
port 1.)
yyIf there is the AutoPlay folder in the USB device and its files are in supported formats, they can be played
back automatically when the USB device is connected to the monitor.
yyIt is recommended that you avoid playing contents using more than two USB ports simultaneously.
yyWith respect to the playback of distribution or contents schedules through SuperSign Software, the
schedule executed last time is played.
ENGLISH
Viewing the Contents List
44
CUSTOMIZING SETTINGS
ENGLISH
CUSTOMIZING SETTINGS
Accessing Main Menus
1Press SETTINGS to access the main menus.
2
Press the navigation buttons to scroll to one of the following menus and press OK.
3
Press the navigation buttons to scroll to the setting or option you want and press OK.
4 When you are finished, press EXIT. When you return to the previous menu, press BACK.
yyPICTURE : Adjusts the image size, quality, or effect.
yyAUDIO : Adjusts the sound quality, effect, or volume level.
yyTIME : Sets the time, date, or timer feature.Exit : Exits My Media.
yyOPTION : Customizes the general settings.
yyNETWORK : Sets up the network setting.
yyMY MEDIA : D
isplay and play movie, photo and music contents stored on your USB or signage device (Internal storage device).
CUSTOMIZING SETTINGS
45
1Press SETTINGS to access the main menus.
2
Press the navigation buttons to scroll to PICTURE and press OK.
3
Press the navigation buttons to scroll to the setting or option you want and press OK.
- To return to the previous level, press BACK.
4
When you are finished, press EXIT.
When you return to the previous menu, press BACK.
The available picture settings are described in the following:
Setting
Energy
Saving
Description
Reduces power consumption by adjusting peak screen brightness.
Level
Off
Disables Energy Saving function.
Minimum/
Medium/
Maximum
Screen Off
Smart Energy
Saving
Selects the brightness level of the backlight.
The screen turns off in 3 seconds.
Adjusts the backlight and contrast depending on the screen brightness.
Level
Off
Disables the Smart Energy Saving function.
On
Picture Mode
Enables the Smart Energy Saving function to save power
consumption as much as the value set in the smart energy saving
rate.
Selects the picture mode optimized for the viewing environment or the programme.
Mode
Vivid
Standard
APS
Cinema
Sport
Game
Calibration
Expert1·2
Aspect Ratio
Heightens contrast, brightness, and sharpness to display vivid
images.
Displays images in standard levels of contrast, brightness, and
sharpness.
APS ( Auto power saving ) mode reduces power consumption by
dimming control.
Optimizes the video image for a cinematic look to enjoy movies as if
you are in a movie theater.
Optimizes the video image for high and dynamic actions by
emphasizing primary Colors such as white, grass, or sky blue.
Optimizes the video image for a fast gaming screen such as PCs or
games.
Applies user-customized white balance based on Standard.
Menu for adjusting picture quality that allows experts and amateurs
to enjoy the best Monitor viewing.
Changes the image size to view images at its optimal size.
ENGLISH
PICTURE Settings
46
CUSTOMIZING SETTINGS
ENGLISH
Setting
Screen
(In RGB
Mode Only)
Description
Customizes the PC display options in RGB mode.
Option
Resolution
Selects a proper resolution.
Auto Configure
Sets to adjust the screen position, clock, and phase automatically.
The displayed image may be unstable for a few seconds while the
configuration is in progress.
Adjusts the options when the picture is not clear, especially when
characters are shaky, after the auto configuration.
Restores the options to the default setting.
Position/Size/
Phase
Reset
Basic image options
Setting
Backlight
Contrast
Description
djusts the brightness of the screen by controlling the LCD backlight. If you
A
decrease the brightness level, the screen becomes darker and the power
consumption will be reduced without any video signal loss.
Increases or decreases the gradient of the video signal. You may use Contrast
when the bright part of the picture is saturated.
Brightness
Adjusts the base level of the signal in the picture. You may use Brightness when
the dark part of the picture is saturated.
Sharpness
Adjusts the level of crispness in the edges between the light and dark areas of the
picture. The lower the level, the softer the image.
Color
Adjusts intensity of all colors.
Tint
Adjusts the balance between red and green levels.
Color Temp.
Picture Option
Set to warm to enhance hotter Colors such as red, or set to cool to make picture
bluish.
You can adjust the picture for each Picture Mode, or adjust the picture settings
according to a specific picture image. First, select a desired Picture Mode.
* This option is unavailable if Picture Mode is set to Vivid.
Sets additional picture option.
Picture Reset
Restores the options to the default setting.
Advanced Control/
Expert Control
NOTE
yyWhen you select a picture mode, related menus are set automatically.
yyWhen using the Smart Energy Saving function, the screen may look saturated in the white area of a still image.
yyIf Energy Saving is set to Minimum, Medium, or Maximum, the Smart Energy Saving function is disabled.
CUSTOMIZING SETTINGS
47
Advanced Control - Picture Mode (Standard/ APS/ Sport/ Game/ Calibration)
Description
Adjusts the contrast to the optimal level according to the brightness of the image.
Dynamic Color
Adjusts color for more natural-looking colors.
Color Gamut
Selects the range of colours that can be expressed.
Skin Color
Sky Color
Skin color spectrum can be separately set to implement the skin color as defined by
the user.
Sky color is set separately.
Grass Color
Natural color spectrum (meadows, hills, etc.) can be separately set.
Gamma
Sets the gradation curve according to the output of the picture signal in relation to the
input signal.
Expert Control - Picture Mode (Cinema/ Expert1/ Expert2)
Setting
Description
Dynamic Contrast
Adjusts the contrast to the optimal level according to the brightness of the image.
(Function works in the following mode - HDMI-DTV)
Color Gamut
Selects the range of colours that can be expressed.
Edge Enhancer
Shows clearer and distinctive yet natural edges of the video.
Color Filter
Filters a specific colour spectrum in RGB colours to fine-tune colour saturation and
hue accurately.
Adjusts the overall tone of the screen as desired. In Expert mode, detailed fine-tuning
can be set via Gamma method, etc.
Color Temperature
Color Management
System
This is a system that experts use when they adjust colour with a test pattern. They
can select from six colour areas (Red / Green / Blue / Cyan / Magenta / Yellow) without
affecting other colours. For normal images, adjustments may not result in noticeable
colour changes.
Picture Option - HDMI(DTV) Mode
Setting
Description
Noise Reduction Reduces screen noise in the video.
MPEG Noise
Reduction
Black Level
Real Cinema
TruMotion
(This feature
is supported
by 65SE3B and
65SE3KB only.)
Reduces noise caused by compressing digital video.
Adjusts the brightness or darkness of the screen to suit the black level of the picture
input using the degree of darkness (black level) of the screen.
Optimizes the screen for movie viewing.
Corrects images to display smoother motion sequences.
• Off : Turn off the TruMotion.
• Smooth/ Clear : De-Judder / De-Blur can be set Auto.
• User : De-Judder / De-Blur can be set manually.
- De-Judder : This function adjusts juddering of
the screen.
- De-Blur : This function adjusts and eliminates blurring of the screen.
TruMotion
◄
Smooth ►
• De-Judder Auto
• De-Blur
Auto
OK
ENGLISH
Setting
Dynamic Contrast
48
CUSTOMIZING SETTINGS
ENGLISH
AUDIO Settings
1
Press SETTINGS to access the main menus.
2
Press the navigation buttons to scroll to AUDIO and press OK.
3
Press the navigation buttons to scroll to the setting or option you want and press OK.
- To return to the previous level, press BACK.
4
When you are finished, press EXIT.
When you return to the previous menu, press BACK.
The available audio options are described in the following:
Setting
Sound Mode
Sound Effect
AV Sync. Adjust
Description
Allows optimized sound for custom Monitor installation.
Level
Standard
Suitable for all types of video.
News/ Music/
Sets audio optimized for a specific genre.
Cinema/ Sport/
Game
the user can select various sound effects.
-S
ound Effect function is available only for Standard mode in Sound Mode menu.
Level
Clear Voice ll
Boosts voice clarity.
Virtual Surround LG’s proprietary audio processing technology allows 5.1ch-like
surround sound from two speakers.
- If Clear Voice ll is set to On, Virtual Surround will not be
chosen.
Equalizer
Adjusts the volume to a level of your choice using the Equalizer.
Balance
Adjusts left/right audio balance.
Reset
You can reset the settings under the Sound Effects menu.
Synchronizes video and audio directly when they do not match.
If you set AV Sync. to ON, you can adjust the sound output to the screen image.
Speaker: Adjusts the synchronization of the sound from the speakers. The "-" button
makes the sound output faster and the "+" button slower than the default value.
Bypass : The audio of an external device without audio delay. Audio may be output
before video as it takes time to process video input into the Monitor.
NOTE
yySome models may not have built-in speakers. In that case, you need to connect external speakers to listen to sound.
CUSTOMIZING SETTINGS
49
1Press SETTINGS to access the main menus.
2
Press the navigation buttons to scroll to TIME and press OK.
3
Press the navigation buttons to scroll to the setting or option you want and press OK.
- To return to the previous level, press BACK.
4
When you are finished, press EXIT.
When you return to the previous menu, press BACK.
The available time settings are described in the following:
Setting
Clock
Description
Sets the time feature.
Level
Auto
Manual
The current time is entered according to the selected country
when connected to a network.
The current time needs to be entered manually.
On/Off Time
Sets the time to turn on or off the monitor set.
Auto Off (15Min.)
If Auto-off is active and there is no input signal, the set switches to off mode
automatically after 15 minutes.
If the monitor is left unattended for a set period of time, it automatically goes into standby
mode.
Automatic Standby
NOTE
yyOff Time/ On Time can be saved for up to seven schedules; the monitor is turned on or off at the preset time in the
schedule list. If multiple preset times are stored in the schedule list, this function works at the nearest time from the
current time.
yyOnce the on or off time is set, these functions operate daily at the preset time.
yyWhen the scheduled power-on and power-off times are the same, the power-off time has priority over the power-on
time if the set is turned on, and vice versa if the set is turned off.
yyIf port 123 is blocked by a firewall, your monitor cannot receive the current time from the network.
ENGLISH
TIME Settings
50
CUSTOMIZING SETTINGS
ENGLISH
OPTION Settings
1Press SETTINGS to access the main menus.
2
Press the navigation buttons to scroll to OPTION and press OK.
3
Press the navigation buttons to scroll to the setting or option you want and press OK.
- To return to the previous level, press BACK.
4
When you are finished, press EXIT.
When you return to the previous menu, press BACK.
The available option settings are described in the following:
Setting
Language
Selects a language for the display text.
Country
Select your country.
DivX(R) VOD
Registers or releases DivX.
Checks DivX Registration Code for playing DivX-protected videos.
Register at http://vod.divx.com.
Uses Registration Code to rent or purchase movies at www.divx.com/vod.
* Rented/purchased DivX files cannot be played if the DivX Registration Code of a
different device is used. Use only the DivX Registration Code granted to this device.
* Converted files not conforming to the DivX Codec Standard may not play or may
produce abnormal images.
Deletes all optional settings and returns to initial default mode.
Initial Setting
Set ID
Tile Mode
Description
You can assign a unique Set ID NO (name assignment) to each product when several
products are connected for display. Specify the number (1 to 255 or 1 to 1,000) using the
button and exit. Use the assigned Set ID to individually control each product using the
Product Control Program.
Tile Mode
To use this function
- Must be displayed with various other products.
- Select Tile Mode, set rows and columns, and then enter the tile ID to
set the location.
- Tile Mode: row x column (row = 1-15, column = 1-15).
- 15 x 15 available.
Auto Config.
Sets to adjust the screen position, clock, and phase automatically.
The displayed image may be unstable for a few seconds while the
configuration is in progress.
Position
Moving the screen position horizontally and vertically.
Size
Natural
Reset
Adjust the horizontal and vertical size of the screen taking into
account the size of the bezel.
The image is omitted by the distance between the screens to be
naturally shown.
Function to initialize and release Tile.
All Tile setting are released when selecting Tile recall and the screen
returns to Full screen.
* Natural is not initialized.
CUSTOMIZING SETTINGS
Description
Creates simple schedules and sets playback using files in My Media.
Level
Add Schedule Creates a contents schedule.
- Media: Select the file to which you want to apply the contents
schedule.
- Select [Create] to register the contents schedule.
Play
Plays a contents schedule.
Delete All
Deletes all registered schedules.
NOTE
yyInformation about registered schedules is stored on your USB storage device.
This feature does not work when your USB storage device has been removed.
yyThe picture size is 1920 x 1080.
yyYou can use photo and video files only.
yyYou can add up to 50 files (photo files + video files = 50).
yyOnly photos whose resolution is 1920 x 1080 or below are supported.
yyThe default display time for photos is 1 minute. Playback time for movies
differs depending on the running time.
yyYou can create up to 7 schedules.
yyYou cannot register a schedule when no file has been selected.
yyContents schedules that have had information forcibly modified using a PC,
etc. may not function properly.
yyWith respect to the playback of distribution or contents schedules through
SuperSign Software, the schedule executed last time is played.
ENGLISH
SETTINGS
Contents Schedule
51
52
CUSTOMIZING SETTINGS
Tile Mode
ENGLISH
This monitor can be tiled with additional monitors to create a large tiled display.
Off
When the Tile Mode
option is disabled
1X2
When using 2 monitors
ID 1
ID 2
2X2
When using 4 monitors
3X3
When using 9 monitors
ID 1
ID 2
ID 1
ID 2
ID 3
ID 3
ID 4
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
Tile ID
4X4
When using 16 monitors
5X5
When using 25 monitors
ID 1
ID 2
ID 3
ID 4
ID 1
ID 2
ID 3
ID 4
ID 5
ID 5
ID 6
ID 7
ID 8
ID 6
ID 7
ID 8
ID 9
ID 10
ID 9
ID 10
ID 11
ID 12
ID 11
ID 12
ID 13
ID 14
ID 15
ID 13
ID 14
ID 15
ID 16
ID 16
ID 17
ID 18
ID 19
ID 20
ID 21
ID 22
ID 23
ID 24
ID 25
Tile Mode - Natural mode
When active, the part of the image that would normally be displayed in the gap between the monitors
is omitted.
Before
After
CUSTOMIZING SETTINGS
53
1Press SETTINGS to access the main menus.
2
Press the navigation buttons to scroll to NETWORK and press OK.
3
Press the navigation buttons to scroll to the setting or option you want and press OK.
- To return to the previous level, press BACK.
4
When you are finished, press EXIT.
When you return to the previous menu, press BACK.
The available option settings are described in the following:
Setting
Network Setting
Description
Configure the network settings.
Network setting
Network Status
When the Wi-Fi dongle is connected, you can view and connect to
any available wireless network.
Display the network status.
Network Connection Options
Setting
Description
Setting from the AP list
Select an AP to connect to a wireless network.
Simple setting
(WPS-button mode)
Press the button on the wireless router that supports PBC to easily connect
to the router.
ENGLISH
NETWORK Settings
54
TROUBLESHOOTING
ENGLISH
TROUBLESHOOTING
No image is displayed
Problem
Action
Is the product power cord connected?
yy
Check if the power cord is correctly plugged into the power
outlet.
yy
The signal from the PC (video card) is out of the vertical or
horizontal frequency range of the product. Adjust the frequency
range by referring to the Specifications in this manual.
yy
The signal cable between PC and product is not connected.
Check the signal cable.
yy
Press the INPUT menu in the remote Control to check the input
signal.
Does the Out of range message
appear?
Does the Check signal cable message
appear?
The Unknown Product message appears when the product is connected.
Problem
Did you install the driver?
Action
yy
Check if the Plug & Play function is supported by referring to the
video card user manual.
The screen image looks abnormal.
Problem
Is the screen position wrong?
Do thin lines appear on the
background screen?
Horizontal noise appears or the
characters look blurred.
The screen is displayed
abnormally.
Resolution
yyD-Sub analog signal - Press the "AUTO" button in the remote control
to automatically select the optimal screen status that fits into the
current mode. If adjustment is not satisfactory, select [PICTURE] [Screen] - [Position] in OSD menu.
yySee if the video card resolution and frequency are supported by the
product. If the frequency is out of range, set to the recommended
resolution in the Control Panel "Display" Setting menu.
yyD-Sub analog signal - Press the "AUTO" button in the remote control
to automatically select an optimal screen status that fits into the
current mode. If adjustment is not satisfactory, select [PICTURE] [Screen] - [Size] in OSD menu.
yyD-Sub analog signal - Press the "AUTO" button in the remote control
to automatically select an optimal screen status that fits into the
current mode. If adjustment is not satisfactory, select [PICTURE] [Screen] - [Phase] in OSD menu.
yyThe proper input signal is not connected to the signal port. Connect
the signal cable that matches with the source input signal.
TROUBLESHOOTING
55
Problem
After-image appears when the
product is turned off.
Action
yy
If you use a fixed image for a long time, the pixels may be
damaged. Use the screen-saver function.
yy
When a dark image is displayed on the screen after an image
with high contrast (black and white or gray), this may cause
image sticking. This is normal for LCD screen products.
The audio function does not work.
Problem
No sound?
Sound is too dull.
Sound is too low.
Action
yy
See if the audio cable is connected properly.
yy
Adjust the volume.
yy
See if the sound is set properly.
yy
Select the appropriate equalizer sound.
yy
Adjust the volume.
Screen color is abnormal.
Problem
Action
Screen has poor color resolution
(16 colors).
yy
Set the number of colors to more than 24 bits (true color). Select
Control Panel - Display - Settings - Color Table menu in Windows.
S creen color is unstable or
mono-colored.
yy
Check the connection status of the signal cable. Or, re-insert the
PC video card.
Do black spots appear on the screen?
yy
Several pixels (red, green, white, or black color) may appear
on the screen, which can be attributable to the unique
characteristics of the LCD panel. This is not a malfunction of the
LCD.
The operation does not work normally.
Problem
The power suddenly turned off.
Action
yy
Is Off Timer set?
yy
Check the power control settings. Power interrupted.
ENGLISH
After-image appears on the product.
56
PRODUCT SPECIFICATIONS
ENGLISH
PRODUCT SPECIFICATIONS
The product specifications below may be changed without prior notice due to upgrade of product functions.
“ ” refers to alternating current (AC), and “
” refers to direct current (DC).
LCD Panel
Screen Type
LCD (Liquid Crystal Display) Panel.
Video Signal
Max. Resolution
1920 x 1080 @ 60 Hz
- It may not be supported depending on the OS or video card type.
Recommended
Resolution
1920 x 1080 @ 60 Hz
- It may not be supported depending on the OS or video card type.
Horizontal
Frequency
RGB : 30 kHz to 83 kHz
HDMI : 30 kHz to 83 kHz
Vertical Frequency
RGB : 50 Hz to 75 Hz
HDMI : 56 Hz to 60 Hz
Synchronization
Type
Separate Sync, Digital
**SE3B
HDMI, DVI-D, RGB, Audio IN/OUT, Speaker OUT, EXT IR IN, USB,
RS-232C IN/OUT, LAN
**SE3KB
HDMI, DVI-D, RGB, Audio IN/OUT, EXT IR IN, USB, RS-232C IN/OUT,
LAN
Input Connector
Embedded battery
Environmental
conditions
Applied
Operating
0 °C to 40 °C
Temperature
10 % to 80 %
Operating Humidity
Storage
Temperature
Storage Humidity
-20 °C to 60 °C
5 % to 95 %
* Applicable only for models that support the speakers
Audio/AUDIO
RMS Audio Output
10 W + 10 W (R + L)
Input Sensitivity
0.7 Vrms
Speaker Impedance
6Ω
PRODUCT SPECIFICATIONS
LCD Panel
Pixel Pitch
0.36375 mm (H) x 0.36375 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 1.4 A
Power
Consumption
On Mode : 50 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
729.4 mm x 428.9 mm x 55.5 mm / 5.2 kg
Head + Stand
729.4 mm x 481 mm x 154.2 mm / 6 kg
Head + Speaker
729.4 mm x 428.9 mm x 95.7 mm / 5.7 kg
Head + Speaker +
Stand
729.4 mm x 481 mm x 154.2 mm / 6.5 kg
LCD Panel
Pixel Pitch
0.36375 mm (H) x 0.36375 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 1.4 A
Power
Consumption
On Mode : 50 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
729.4 mm x 428.9 mm x 55.5 mm / 5.4 kg
Head + Stand
729.4 mm x 481 mm x 154.2 mm / 6.2 kg
Dimensions (Width
x Height x Depth) /
Weight
32SE3KB
Dimensions (Width
x Height x Depth) /
Weight
ENGLISH
32SE3B
57
58
PRODUCT SPECIFICATIONS
ENGLISH
43SE3B
LCD Panel
Pixel Pitch
0.4902 mm (H) X 0.4902 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 0.9 A
Power
Consumption
On Mode : 60 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
969.6 mm x 563.9 mm x 38.6 mm / 9.8 kg
Head + Stand
969.6 mm x 622.2 mm x 193 mm / 12.3 kg
Head + Speaker
969.6 mm x 563.9 mm x 67.9 mm / 10.3 kg
Head + Speaker +
Stand
969.6 mm x 622.2 mm x 193 mm / 12.8 kg
LCD Panel
Pixel Pitch
0.4902 mm (H) X 0.4902 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 0.9 A
Power
Consumption
On Mode : 60 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
969.6 mm x 563.9 mm x 54.0 mm / 10 kg
Head + Stand
969.6 mm x 622.2 mm x 193 mm / 12.5 kg
Dimensions (Width
x Height x Depth) /
Weight
43SE3KB
Dimensions (Width
x Height x Depth) /
Weight
PRODUCT SPECIFICATIONS
LCD Panel
Pixel Pitch
0.55926 mm (H) X 0.55926 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 1.0 A
Power
Consumption
On Mode : 65 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
1102.2 mm x 638.5 mm x 38.6 mm / 14.1 kg
Head + Stand
1102.2 mm x 696.8 mm x 219.6 mm / 17.4 kg
Head + Speaker
1102.2 mm x 638.5 mm x 67.9 mm / 14.6 kg
Head + Speaker +
Stand
1102.2 mm x 696.8 mm x 219.6 mm / 17.9 kg
LCD Panel
Pixel Pitch
0.55926 mm (H) X 0.55926 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 1.0 A
Power
Consumption
On Mode : 65 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
1102.2 mm x 638.5 mm x 54.0 mm / 14.3 kg
Head + Stand
1102.2 mm x 696.8 mm x 219.6 mm / 17.6 kg
Dimensions (Width
x Height x Depth) /
Weight
49SE3KB
Dimensions (Width
x Height x Depth) /
Weight
ENGLISH
49SE3B
59
60
PRODUCT SPECIFICATIONS
ENGLISH
55SE3B
LCD Panel
Pixel Pitch
0.630 mm (H) x 0.630 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 1.1 A
Power
Consumption
On Mode : 70 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
1238 mm x 714.9 mm x 38.6 mm / 17.3 kg
Head + Stand
1238 mm x 773.4 mm x 219.6 mm / 20.6 kg
Head + Speaker
1238 mm x 714.9 mm x 67.9 mm / 17.8 kg
Head + Speaker +
Stand
1238 mm x 773.4 mm x 219.6 mm / 21.1 kg
LCD Panel
Pixel Pitch
0.630 mm (H) x 0.630 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 1.1 A
Power
Consumption
On Mode : 70 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
1238 mm x 714.9 mm x 54.0 mm / 17.5 kg
Head + Stand
1238 mm x 773.4 mm x 219.6 mm / 20.8 kg
Dimensions (Width
x Height x Depth) /
Weight
55SE3KB
Dimensions (Width
x Height x Depth) /
Weight
PRODUCT SPECIFICATIONS
LCD Panel
Pixel Pitch
0.744 mm (H) x 0.744 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 1.4 A
Power
Consumption
On Mode : 95 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
1456.9 mm x 838 mm x 41.1 mm / 27.7 kg
Head + Stand
1456.9 mm x 898.1 mm x 293.7 mm / 32.9 kg
Head + Speaker
1456.9 mm x 838 mm x 70.4 mm / 28.2 kg
Head + Speaker +
Stand
1456.9 mm x 898.1 mm x 293.7 mm / 33.4 kg
LCD Panel
Pixel Pitch
0.744 mm (H) x 0.744 mm (V)
Power
Rated Voltage
AC 100-240 V~ 50/60 Hz 1.4 A
Power
Consumption
On Mode : 95 W Typ.
Sleep Mode (RGB) : ≤ 0.7 W
Sleep Mode (HDMI) : ≤ 0.7 W
Off Mode : ≤ 0.5 W
Head
1456.9 mm x 838 mm x 56.5 mm / 27.9 kg
Head + Stand
1456.9 mm x 898.1 mm x 293.7 mm / 33.1 kg
Dimensions (Width
x Height x Depth) /
Weight
65SE3KB
Dimensions (Width
x Height x Depth) /
Weight
ENGLISH
65SE3B
61
62
PRODUCT SPECIFICATIONS
The illustrations in this manual may differ from the actual product and accessories.
Please see Mounting on a wall section for screw sizes.
The product specifications below may be changed without prior notice due to upgrade of product functions.
(Unit: mm)
32SE3*
55.5
32.1
428.9
729.4
481.1
13
59.9
18
264.7
121.3
200
200
264.7
107.7
ENGLISH
Product Dimensions
PRODUCT SPECIFICATIONS
63
(Unit: mm)
38.6
38.6
27.7
27.7
622.2
563.9
969.6
11.9
72.9
18
72.9
54.0
43SE3B
107.2
384.8
200
200
193.7
384.8
43SE3KB
ENGLISH
43SE3*
64
PRODUCT SPECIFICATIONS
(Unit: mm)
38.6
38.6
27.7
27.7
638.5
1102.2
696.8
11.9
18
92.1
92.1
54.0
49SE3B
401.1
154.8
300
300
401.1
49SE3KB
183.7
ENGLISH
49SE3*
PRODUCT SPECIFICATIONS
65
(Unit: mm)
38.6
1238
27.7
714.9
773.4
27.7
38.6
11.9
92.1
18
92.1
54.0
55SE3B
231.4
469
300
300
183.5
469
55SE3KB
ENGLISH
55SE3*
66
PRODUCT SPECIFICATIONS
(Unit: mm)
41.1
1456.9
30.2
41.1
30.2
838
898.1
11.9
18
116.1
116.1
56.5
65SE3B
578.4
354.6
300
300
578.4
183.5
ENGLISH
65SE3*
65SE3KB
PRODUCT SPECIFICATIONS
67
HDMI / DVI-D (DTV) supported mode
RGB (PC) supported mode
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
720 x 400
31.468
70.8
480/60P
31.5
60
640 x 480
31.469
59.94
576/50P
31.25
50
37.5
50
800 x 600
37.879
60.317
720/50P
1024 x 768
48.363
60
720/60P
45
60
28.1
50
1280 x 720
44.772
59.855
1080/50i
1280 x 960
60
60
1080/60i
33.75
60
56.25
50
67.5
60
1152 x 864
57.717
59.934
1080/50P
1280 x 1024
63.981
60.02
1080/60P
1920 x 1080
67.5
60
HDMI / DVI-D (PC) supported mode
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
640 x 480
31.469
59.94
800 x 600
37.879
60.317
1024 x 768
48.363
60
1280 x 720
44.772
59.855
1366 x 768
47.7
60
1280 x 1024
63.981
60.02
1680 x 1050
65.290
59.954
1920 x 1080
67.5
60
NOTE
yyIn the DVI-D or HDMI input, you can select the PC/
DTV mode optionally. It is recommended that you
select PC mode when connecting to a PC, and DTV
mode when connecting to other devices.
NOTE
yyPC resolutions available as the input label option in
RGB and HDMI / DVI-D input modes : 640 x 480 / 60
Hz, 1280 x 720 / 60 Hz, 1920 x 1080 / 60 Hz and DTV
resolutions : 480p, 720p, 1080p.
yyVertical frequency: To enable the user to watch the
product display, screen image should be changed
tens of times every second like a fluorescent lamp.
The vertical frequency or refresh rate is the times of
image display per second. The unit is Hz.
yyHorizontal frequency: The horizontal interval is the
time to display one vertical line. When 1 is divided
by the horizontal interval, the number of horizontal
lines displayed every second can be tabulated as
the horizontal frequency. The unit is kHz.
ENGLISH
Resolution
68
IR CODES
ENGLISH
IR CODES
yyAll models do not support the HDMI/USB function.
yySome key codes are not supported depending on the model.
Code (Hexa)
08
Function
Note
R/C BUTTON
Power
0B
INPUT
R/C BUTTON
C4
MONITOR ON
R/C BUTTON
C5
MONITOR OFF
95
ENERGY SAVING (
DC
3D
R/C BUTTON
10 to 19
Number Key 0 to 9
R/C BUTTON
53
1/a/A
R/C BUTTON
2F
CLEAR
R/C BUTTON
02
Volume
R/C BUTTON
03
Volume
R/C BUTTON
79
ARC
R/C BUTTON
99
AUTO
R/C BUTTON
09
MUTE
E0
BRIGHTNESS
(Page UP)
R/C BUTTON
E1
BRIGHTNESS
(Page Down)
R/C BUTTON
4D
PSM
R/C BUTTON
AA
INFO
R/C BUTTON
5F
W.BAL
R/C BUTTON
43
SETTINGS
R/C BUTTON
40
Up
R/C BUTTON
41
Down
R/C BUTTON
07
Left
R/C BUTTON
06
Right
R/C BUTTON
3F
S.MENU
R/C BUTTON
44
OK
R/C BUTTON
28
BACK
R/C BUTTON
5B
EXIT
R/C BUTTON
R/C BUTTON
R/C BUTTON
R/C BUTTON
7E
7B
)
R/C BUTTON
TILE (Tile Mode)
R/C BUTTON
B1
R/C BUTTON
B0
R/C BUTTON
BA
R/C BUTTON
IR CODES
Function
Note
R/C BUTTON
8E
R/C BUTTON
72
Red Key (PICTURE ID ON)
R/C BUTTON
71
Green Key (PICTURE ID OFF)
R/C BUTTON
63
Yellow Key
R/C BUTTON
61
Blue Key
R/C BUTTON
ENGLISH
Code (Hexa)
8F
69
70
TO CONTROL MULTIPLE PRODUCTS
ENGLISH
TO CONTROL MULTIPLE PRODUCTS
yyUse this method to connect several products to a single PC. You can control several products at a time by connecting
them to a single PC.
yyIn the Option menu, Set ID must be between 1 and 255 (or from 1 to 1,000) without being duplicated.
Connecting the Cable
Connect the RS-232C cable as shown in the picture.
yyThe RS-232C protocol is used for communication between the PC and product. You can turn the product on or off,
select an input source or adjust the OSD menu from your PC.
Monitor 4
RS-232C
OUT
RS-232C
IN
Monitor 3
RS-232C
OUT
RS-232C
IN
Monitor 2
RS-232C
OUT
RS-232C
IN
4P Cable
(not included)
PC
Monitor 1
RS-232C
OUT
RS-232C
IN
RS-232C Gender
RS-232C Cable
(not included)
TO CONTROL MULTIPLE PRODUCTS
4P Cable
4-Wire Configurations (Standard RS-232C cable)
Set
Set
TXD
RXD
GND
IR
RXD
TXD
GND
IR
NOTE
•• When using three-wire connections (nonstandard), an IR daisy chain cannot be used.
•• If you want to control multiple units
simultaneously, use 3.5 mm 4-pole cables (sold
separately).
RS-232C Cable
8-Wire Configurations (Standard RS-232C cable)
PC
DCD
RXD
TXD
GND
DTR
DSR
RTS
CTS
1
2
3
5
4
6
7
8
D-Sub 9
(Female)
RS-232C
Gender
1
3
2
5
6
4
8
7
D-Sub 9
(Female)
DCD
TXD
RXD
GND
DSR
DTR
CTS
RTS
•• Baud Rate 9600 BPS
•• Data Length 8 bit
•• Parity Bit None
•• Stop Bit 1 bit
•• Flow Control None
•• Communication Code ASCII code
•• Use a crossed (reverse) cable
ENGLISH
Communication Parameter
RS-232C Configurations
71
72
TO CONTROL MULTIPLE PRODUCTS
ENGLISH
Command Reference List
COMMAND
1
DATA
(Hexadecimal)
2
01
Power
k
a
00 to 01
02
Select input
x
b
See [Select input]
03
Aspect ratio
k
c
See [Aspect ratio]
04
Energy saving
j
q
See [Energy saving]
05
Picture mode
d
x
See [Picture mode]
06
Contrast
k
g
00 to 64
07
Brightness
k
h
00 to 64
08
Sharpness
k
k
00 to 32
09
Color
k
i
00 to 64
10
Tint
k
j
00 to 64
11
Color temperature
x
u
00 to 64
12
H position
f
q
00 to 64
13
V position
f
r
00 to 64
14
H size
f
s
00 to 64
15
Auto Config.
j
u
01
16
Balance
k
t
00 to 64
17
Sound Mode
d
y
See [Sound mode]
18
Mute
k
e
00 to 01
19
Volume
k
f
00 to 64
20
Clock 1 (year/month/day)
f
a
See [Clock 1]
21
Clock 2 (hour/minute/second)
f
x
See [Clock 2]
22
Off time schedule
f
c
00 to 01
23
On time schedule
f
b
00 to 01
24
Off timer (repeat mode/time)
f
e
See [Off timer]
25
On timer (repeat mode/time)
f
d
See [On timer]
26
On timer input
f
u
See [On timer input]
27
Automatic Standby
m
n
00 to 01
28
Auto off
f
g
00 to 01
29
Language
f
i
See [Language]
30
Reset
f
k
00 to 02
31
Current temperature
d
n
FF
32
Key
m
c
See [Key]
33
Time elapsed
d
l
FF
34
Product serial number
f
y
FF
TO CONTROL MULTIPLE PRODUCTS
DATA
(Hexadecimal)
2
35
Software version
f
z
FF
36
White balance red gain
j
m
00 to FE
37
White balance green gain
j
n
00 to FE
38
White balance blue gain
j
o
00 to FE
39
Backlight
m
g
00 to 64
40
Screen off
k
d
00 to 01
41
Tile Mode
d
d
See [Tile Mode]
42
Tile Mode Check
d
z
FF
43
Tile ID
d
i
Refer to ‘Tile ID'.
44
Tile H Position
d
e
00 to 32
45
Tile V Position
d
f
00 to 32
46
Tile H Size
d
g
00 to 32
47
Tile V Size
d
h
00 to 32
48
Natural Mode (In Tile mode)
d
j
00 to 01
NOTE
yyDuring USB operations such as Dvix or EMF, all commands except Power (k a) and Key (m c) are not executed and
treated as NG.
yySome commands are not supported depending on the model.
yyThe ‘f f’ command which shows the status of a certain command does not display the OSD as the result in order to be
compatible with SuperSign program.
ENGLISH
COMMAND
1
73
74
TO CONTROL MULTIPLE PRODUCTS
ENGLISH
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command1]
Identifies the factory setting and the user setting modes.
* [Command2]
Controls monitors.
* [Set ID]
Used for selecting a set you want to control. A Set ID can be assigned to each set from 1
to 255 (from 01H to FFH), or from 1 to 1,000 (from 001H to 3e8H) in certain models, under
OPTION in the OSD menu. Selecting '00H' or '000H' for Set ID allows the simultaneous control
of all connected monitors. (It may not be supported depending on the model.)
* [Data]
Transmits command data.
Data count may increase depending on the command.
* [Cr]
Carriage Return. Corresponds to '0x0D' in ASCII code.
*[]
White Space. Corresponds to '0x20' in ASCII code.
Acknowledgement
[Command2][ ][Set ID][ ][OK/NG][Data][x]
* T he Product transmits an ACK (acknowledgement) based on this format when receiving normal data. At this
time, if the data is FF, it indicates the present status data. If the data is in data write mode, it returns the data
of the PC computer.
* If a command is sent with Set ID '00' (=0x00) or '000 (=0x000)', the data is reflected to all monitor sets and
they do send any acknowledgement (ACK).
* If the data value 'FF' is sent in control mode via RS-232C, the current setting value of a function can be
checked (only for some functions).
* Some commands may not be supported on some models.
TO CONTROL MULTIPLE PRODUCTS
04. Energy saving (Command: j q)
Sets the energy saving function.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data][x]
* Only when the monitor is fully powered on, the
acknowledgement signal is returned properly.
* There may be a delay between the transmission and
acknowledgement signals.
02. Select input (Command: x b)
Selects an input signal.
[j][q][ ][Set ID][ ][Data][Cr]
Data
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
** This may not be supported on some models.
05. Picture mode (Command: d x)
Selects a picture mode.
Transmission
[d][x][ ][Set ID][ ][Data][Cr]
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data
60: RGB
70: DVI-D (PC)
80: DVI-D (DTV)
90: HDMI (HDMI1) (DTV)
A0: HDMI (HDMI1) (PC)
Acknowledgement
Data
[b][ ][Set ID][ ][OK/NG][Data][x]
[x][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
Adjusts the screen contrast.
Transmission
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data
01: 4:3
02: 16:9
04: Zoom (HDMI)(DTV)
06: Auto ratio (HDMI)(DTV)
09: Original (≥ 720p) (HDMI) (DTV)
10 to 1F: Cinema zoom 1 to 16 (HDMI) (DTV)
* Available data types differ depending on the input signal. For more
information, see the aspect ratio section of the owner's manual.
* The aspect ratio may differ depending on the model's input
configuration.
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
00: Vivid
01: Standard
02: Cinema
03: Sport
04: Game
05: Expert 1
06: Expert 2
08: Eco
11 : Calibration
Acknowledgement
* Some input signals may not be supported on some models.
03. Aspect ratio (Command: k c)
Adjusts the aspect ratio.
00: Off
01: Minimum
02: Medium
03: Maximum
04: Automatic
05: Screen off
[k][g][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Contrast 0 to 100
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
01. Power (Command: k a)
Controls the power on/off of the set.
75
76
TO CONTROL MULTIPLE PRODUCTS
ENGLISH
07. Brightness (Command: k h)
Adjusts the screen brightness.
10. Tint (Command: k j)
Adjusts the screen tint.
Transmission
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Brightness 0 to 100
[k][j][ ][Set ID][ ][Data][Cr]
Data
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
[j][ ][Set ID][ ][OK/NG][Data][x]
08. Sharpness (Command: k k)
Adjusts the screen sharpness.
11. Color temperature (Command: x u)
Adjusts the screen color temperature.
Transmission
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data
00 to 32: Sharpness 0 to 50
[x][u][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Warm 50 to cool 50
Acknowledgement
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
[u][ ][Set ID][ ][OK/NG][Data][x]
09. Color (Command: k i)
Adjusts the screen color.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Tint red 50 to green 50
Acknowledgement
12. H position (Command: f q)
Adjusts the horizontal position of the screen.
This function is only available when the Tile Mode is set to Off.
* The operational range varies depending on the RGB input
resolution.
(Only available in RGB-PC input mode)
00 to 64: Color 0 to 100
Transmission
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
[f ][q][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Min -50 (left) to max 50 (right)
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
TO CONTROL MULTIPLE PRODUCTS
Transmission
16. Balance (Command: k t)
Adjusts the sound balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
Acknowledgement
[f ][r][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Left 50 to right 50
[t][ ][Set ID][ ][OK/NG][Data][x]
00 to 64: Min -50 (down) to max 50 (up)
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
14. H size (Command: f s)
Adjusts the horizontal size of the screen.
This function is only available when the Tile Mode is set to Off.
* The operational range varies depending on the RGB input
resolution.
(Only available in RGB-PC input mode)
Transmission
[f ][s][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Min -50 (small) to max 50 (large)
Acknowledgement
17. Sound mode (Command: d y)
Selects a sound mode.
Transmission
[d][y][ ][Set ID][ ][Data][Cr]
Data
[s][ ][Set ID][ ][OK/NG][Data][x]
01: Standard
02: Music
03: Cinema
04: Sport
05. Game
07. News
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
15. Auto Config. (Command: j u)
Automatically corrects position and shaking of the picture.
(Only available in RGB-PC input mode)
18. Mute (Command: k e)
Mutes/unmutes the sound.
Transmission
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 01: Execution
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
[k][e][ ][Set ID][ ][Data][Cr]
Data
00: Mute
01: Unmute
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
13. V position (Command: f r)
Adjusts the vertical position of the screen.
This function is only available when the Tile Mode is set to Off.
* The operational range varies depending on the RGB input
resolution.
(Only available in RGB-PC input mode)
77
78
TO CONTROL MULTIPLE PRODUCTS
ENGLISH
19. Volume (Command: k f)
Adjusts the playback volume.
22. Off time schedule (Command: f c)
Enables/disables the on time schedule.
Transmission
Transmission
[k][f ][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Volume 0 to 100
[f ][c][ ][Set ID][ ][Data][Cr]
Data
Acknowledgement
Acknowledgement
[f ][ ][Set ID][ ][OK/NG][Data][x]
20. Clock 1 (year/month/day) (Command: f a)
Adjusts the Clock 1 (year/month/day) value.
[c][ ][Set ID][ ][OK/NG][Data][x]
23. On time schedule (Command: f b)
Enables/disables the on time schedule.
Transmission
Transmission
[f ][a][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
00 to 14: Year 2010 to 2040
Data2
01 to 0C: January to December
Data3
01 to 1F: 1st to 31st
* Enter "fa [Set ID] ff" to view the Clock 1 (year/month/day)
settings.
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
21. Clock 2 (hour/minute/second) (Command: f x)
Adjusts the Clock 2 (hour/minute/second) value.
Transmission
[f ][x][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
00 to 17: 00 to 23 hours
Data2
00 to 3B: 00 to 59 minutes
Data3
00 to 3B: 00 to 59 seconds
* Enter "fa [Set ID] ff" to view the Clock 2 (hour/minute/second)
settings.
** This function is only available when Clock 1 (year/month/
day) is set.
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
00: Off
01: On
[f ][b][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
TO CONTROL MULTIPLE PRODUCTS
Transmission
[f ][e][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
1. F1 to F7 (reading data)
F1: Read the 1st off timer data
F2: Read the 2nd off timer data
F3: Read the 3rd off timer data
F4: Read the 4th off timer data
F5: Read the 5th off timer data
F6: Read the 6th off timer data
F7: Read the 7th off timer data
2. E1 to E7 (deleting one index), E0 (deleting all indexes)
E0: Erase all off timer setting
E1: Erase the 1st off timer setting
E2: Erase the 2nd off timer setting
E3: Erase the 3rd off timer setting
E4: Erase the 4th off timer setting
E5: Erase the 5th off timer setting
E6: Erase the 6th off timer setting
E7: Erase the 7th off timer setting
3. 01 to 0C (setting the day of the week for off timer)
01: Once
02. Daily
03: Mon - Fri
04: Mon - Sat
05: Sat - Sun
06. Every Sunday
07. Every Monday
08. Every Tuesday
09. Every Wednesday
0A. Every Thursday
0B. Every Friday
0C. Every Saturday
Data2
00 to 17: 00 to 23 hours
Data3
00 to 3B: 00 to 59 minutes
* To read or delete the Off Time list, set FFH for [Data2] and
[Data3].
Example 1: fe 01 f1 ff ff - Read the 1st index data from off timer.
Example 2: fe 01 e1 ff ff - Delete the 1st index data from off
timer.
Example 3: fe 01 04 02 03 - Sets Off Timer to 02:03 for MondaySaturday.
* This function is only available when Clock 1 (year/month/day)
and Clock 2 (hour/minute/second) are set.
25. On timer (repeat mode/time) (Command: f d)
Configures the on time (repeat mode/time) settings.
Transmission
[f ][d][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
1. F1 to F7 (reading data)
F1: Read the 1st on timer data
F2: Read the 2nd on timer data
F3: Read the 3rd on timer data
F4: Read the 4th on timer data
F5: Read the 5th on timer data
F6: Read the 6th on timer data
F7: Read the 7th on timer data
2. E1 to E7 (deleting one index), E0 (deleting all indexes)
E0: Erase all on timer setting
E1: Erase the 1st on timer setting
E2: Erase the 2nd on timer setting
E3: Erase the 3rd on timer setting
E4: Erase the 4th on timer setting
E5: Erase the 5th on timer setting
E6: Erase the 6th on timer setting
E7: Erase the 7th on timer setting
3. 01 to 0C (setting the day of the week for the on timer)
01: Once
02. Daily
03: Mon - Fri
04: Mon - Sat
05: Sat - Sun
06. Every Sunday
07. Every Monday
08. Every Tuesday
09. Every Wednesday
0A. Every Thursday
0B. Every Friday
0C. Every Saturday
Data2
00 to 17: 00 to 23 hours
Data3
00 to 3B: 00 to 59 minutes
* To read or delete an on timer list you have set, [Data2][Data3]
must be set to FFH.
Example 1: fd 01 f1 ff ff - Read the 1st index data from on timer.
Example 2: fd 01 e1 ff ff - Delete the 1st index data from on
timer.
Example 3: fd 01 04 02 03 - Set on timer at 02:03 on Monday to
Saturday.
* This function is only available when Clock 1 (year/month/day)
and Clock 2 (hour/minute/second) are set.
Acknowledgement
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
[d][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
ENGLISH
24. Off timer (repeat mode/time) (Command: f e)
Configures the off time (repeat mode/time) settings.
79
80
TO CONTROL MULTIPLE PRODUCTS
ENGLISH
26. On timer input (Command: f u)
Adds a new schedule entry by selecting input for the current on
timer setting.
28. Auto off (Command: f g)
Configures the automatic off settings.
Transmission
Transmission
[f ][u][ ][Set ID][ ][Data1][Cr]
[f ][u][ ][Set ID][ ][Data1][Data2][Cr]
[f ][g][ ][Set ID][ ][Data][Cr]
Data Data (adding schedule)
60: RGB
70: DVI-D
90: HDMI (HDMI1)
Data1
1. f1h to f7h (reading data)
F1: Select the 1st schedule input source
F2: Select the 2nd schedule input source
F3: Select the 3rd schedule input source
F4: Select the 4th schedule input source
F5: Select the 5th schedule input source
F6: Select the 6th schedule input source
F7: Select the 7th schedule input source
Data2
1. ffh (reading data)
To read the schedule input, enter FFH for [Data2].
If no schedule is available for [Data1] when attempting to read
or change the schedule data, the text NG will be displayed and
the operation will fail.
(Example 1: fu 01 60 - Move existing schedule entries down
one row each and save RGB as input source for the 1st schedule
entry.)
(Example 2: fu 01 f1 ff - Read the 1st schedule input data.)
* This function is only supported when 1 (year/month/date), 2
(hour/minute/second) and On Time (repeat mode/time) are set.
** Input may not be supported on some models.
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
[u][ ][Set ID][ ][OK/NG][Data1][Data2][x]
00: Off (Will not turn off after 15 minutes)
01: On (Off after 15 minutes)
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
29. Language (Command: f i)
Sets the OSD language.
Transmission
[f ][i][ ][Set ID][ ][Data][Cr]
Data
00: Czech
01: Danish
02: German
03: English
04: Spanish (Europe)
05: Greek
06: French
07: Italian
08: Dutch
09: Norwegian
0A: Portuguese
0B: Portuguese (Brazil)
0C: Russian
0D: Finnish
0E: Swedish
0F: Korean
10: Chinese (Cantonese)
11: Japanese
12: Chinese (Mandarin)
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
27. Automatic standby (Command: m n)
Configures the automatic standby settings.
Transmission
[m][n][ ][Set ID][ ][Data][Cr]
Data
00: Off (Will not turn off after 4/6/8 hours)
01: 4 hours (Off after 4 hours)
02: 6 hours (Off after 6 hours)
03: 8 hours (Off after 8 hours)
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
TO CONTROL MULTIPLE PRODUCTS
33. Time elapsed (Command: d l)
Checks the elapsed time.
Transmission
[d][l][ ][Set ID][ ][Data][Cr]
Transmission
[f ][k][ ][Set ID][ ][Data][Cr]
Data
00: Picture reset
01: Screen reset
02: Initial settings (factory reset)
Data
FF: Read status
Acknowledgement
[l][ ][Set ID][ ][OK/NG][Data][x]
* The data received is shown as a hexadecimal value.
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
34. Product serial number (Command: f y)
Checks the serial number of the product.
Transmission
31. Current temperature (Command: d n)
Checks the inside temperature value.
[f ][y][ ][Set ID][ ][Data][Cr]
Data
Acknowledgement
Transmission
[y][ ][Set ID][ ][OK/NG][Data][x]
[d][n][ ][Set ID][ ][Data][Cr]
Data FF: Check status
FF: Check product serial number
* Data is in ASCII code.
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
[n][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
* Temperature is displayed as a hexadecimal value.
35. Software version (Command: f z)
Checks the software version of the product.
Transmission
[f ][z][ ][Set ID][ ][Data][Cr]
32. Key (Command: m c)
Sends a key code for the IR remote control.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
DataIR_KEY_CODE
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
For key codes, see IR Codes.
* Some key codes may not be supported on some models.
Data
FF: Check software version
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
30. Reset (Command: f k)
Resets settings for Picture, Screen and Audio or restores factory
settings.
(Screen reset can only be performed in RGB input mode.)
81
82
TO CONTROL MULTIPLE PRODUCTS
ENGLISH
36. White balance red gain (Command: j m)
Adjusts the white balance red gain value.
39. Backlight (Command: m g)
Adjusts the back light brightness.
Transmission
Transmission
[j][m][ ][Set ID][ ][Data][Cr]
Data 00 to FE: Red gain 0 to 254
[m][g][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Back light brightness 0 to 100
Acknowledgement
Acknowledgement
[m][ ][Set ID][ ][OK/NG][Data][x]
[g][][set ID][][OK/NG][Data][x]
** This may not be supported on some models.
37. White balance green gain (Command: j n)
Adjusts the white balance green gain value.
40. Screen off (Command: k d)
Turns the screen on or off.
Transmission
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
[j][n][ ][Set ID][ ][Data][Cr]
Data
Data 00 to FE: Green gain 0 to 254
00: Turns the screen on
01: Turns the screen off
Acknowledgement
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
[d][ ][Set ID][ ][OK/NG][Data][x]
41. Tile Mode (Command: d d)
To set a Tile Mode and Tile Column/ Row values.
Transmission
[d][d][ ][Set ID][ ][Data][Cr]
38. White balance blue gain (Command: j o)
Adjusts the white balance blue gain value.
Transmission
[j][o][ ][Set ID][ ][Data][Cr]
Data 00 to FE: Blue gain 0 to 254
Acknowledgement
[o][ ][Set ID][ ][OK/NG][Data][x]
Data
00 to FF: 1
st byte - Tile Row 2nd byte - Tile Column
*00, 01, 10, 11 means Tile Mode Off
** It may not be supported depending on the model.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data][x]
TO CONTROL MULTIPLE PRODUCTS
Transmission
[d][z][ ][Set ID][ ][Data][Cr]
Data
FF: Check Tile Mode status.
** It may not be supported depending on the model.
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
Data1
Data2
Data3
00: Tile Mode Off
01: Tile Mode On
00 to 0F: Tile Row
00 to 0F: Tile Column
43. Tile ID (Command: d i)
To set Tile ID.
Transmission
[d][i][ ][Set ID][ ][Data][Cr]
Data
01 to E1:
Tile ID 01 to 225**
FF: Check Tile ID
** Data could not be set over (Tile Column) x (Tile Row).
** It may not be supported depending on the model.
45. Tile V Position (Command: d f)
To adjust the Tile Vertical position.
* This function is available only when the Natural option of the
Tile Mode is set to Off while the Tile Mode set to On.
Transmission
[d][f ][ ][Set ID][ ][Data][Cr]
Data
0 to 32: 0 (Bottom) to 50 (Top)
* Bottom/Top values depend on Tile Vertical size.
** It may not be supported depending on the model.
Acknowledgement
[f ][ ][Set ID][ ][OK/NG][Data][x]
46. Tile H Size (Command: d g)
To adjust the Tile Horizontal Size.
*Set Tile H Position to 0x32 before setting Tile H Size.
* This function is available only when the Natural option of the
Tile Mode is set to Off while the Tile Mode set to On.
Transmission
[d][g][ ][Set ID][ ][Data][Cr]
Data
00 to 32: 0 to 50
** It may not be supported depending on the model.
Acknowledgement
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
[g][ ][Set ID][ ][OK/NG][Data][x]
*NG will be return if data is over (Tile Column) x (Tile Row),
except 0xFF.
44. Tile H Position (Command: d e)
To adjust the Tile Horizontal position.
* This function is available only when the Natural option of the
Tile Mode is set to Off while the Tile Mode set to On.
Transmission
[d][e][ ][Set ID][ ][Data][Cr]
Data
00 to 32: -50 (Left) to 0 (Right)
*Left/Right values depend on Tile H size.
** It may not be supported depending on the model.
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data][x]
47. Tile V Size (Command: d h)
To adjust the Tile Vertical size.
*Set Tile V Position to 0x00 before setting Tile V Size.
* This function is available only when the Natural option of the
Tile Mode is set to Off while the Tile Mode set to On.
Transmission
[d][h][ ][Set ID][ ][Data][Cr]
Data
00 to 32: 0 to 50
** It may not be supported depending on the model.
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
42. Tile Mode Check (Command: d z)
To check Tile Mode status.
83
84
TO CONTROL MULTIPLE PRODUCTS
ENGLISH
48. Natural Mode (In Tile Mode) (Command : d j)
To display the image naturally, the part of the image that would
normally be displayed in the gap between the monitors is
omitted.
Transmission
[d][j][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
NOTE
yy65SE3B and 65SE3KB are not certified with
EPA’s ENERGY STAR.
Make sure to read the Safety Precautions
before using the product.
The model and serial numbers of the SET are
located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
To obtain the source code under GPL, LGPL,
MPL, and other open source licenses, that is
contained in this product, please visit
http://opensource.lge.com.
In addition to the source code, all referred
license terms, warranty disclaimers and
copyright notices are available for download.
LG Electronics will also provide open source
code to you on CD-ROM for a charge covering
the cost of performing such distribution (such
as the cost of media, shipping, and handling)
upon email request to opensource@lge.com.
This offer is valid for three (3) years from the
date on which you purchased the product.
WARNING -This is a class A product. In a domestic
environment this product may cause radio
interference, in which case the user may be
required to take adequate measures.
Temporary noise is normal when powering ON
or OFF this device.
Service
ENGLISH
DEUTSCH
Service
Wartun
Unplug the monitor from the wall outlet and
refer servicing to qualified service personnel
when :
The power cord or plug is damaged or
yy
frayed.
Liquid has been spilled into the monitor.
yy
The monitor has been exposed to rain or
yy
water.
The monitor does not operate normally
yy
following the operating instructions. Adjust
only those controls that are covered in
the operating instructions. An improper
adjustment of other controls may result in
damage and often requires extensive work
by a qualified technician to restore the
monitor to normal operation.
The monitor has been dropped or the cabinet
yy
has been damaged.
The monitor exhibits a distinct change in
yy
performance.
Snapping or popping from the monitor is
yy
continuous or frequent while the monitor is
operating. It is normal for some monitors to
make occasional sounds when being turned
on or off, or when changing video modes.
Do not attempt to service the monitor yourself,
as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
Bei folgenden Fehlerbedingungen ist der
Netzstecker des Monitors zu ziehen und der
Kundendienst zu benachrichtigen:
Wenn der Netzstecker beschadigt oder das
yy
Netzkabel ausgefranst ist.
Wenn Flussigkeit in den Monitor gelaufen ist.
yy
Wenn der Monitor Regen oder Feuchtigkeit
yy
ausgesetzt worden ist.
Wenn der Monitor trotz Befolgung
yy
aller Bedienungsanweisungen nicht
ordnungsgemass arbeitet. Benutzen Sie
ausschliesslich die Bedienelemente, die
in den Hinweisen dieses Handbuchs
beschrieben werden. Werden andere
Bedienelemente geandert oder verstellt,
konnen Schaden entstehen, die nur von
einem qualifizierten Service-Techniker
behoben werden konnen.
Wenn der Monitor fallengelassen und das
yy
Gehause beschadigt wurde.
Wenn beim Betrieb des Monitors haufig oder
yy
lang anhaltend knackende oder knallende
Nebengerausche auftreten. Hiermit sind
nicht die typischen Gerausche gemeint, die
beim Ein- oder Ausschalten des Monitors zu
horen sind.
Fuhren Sie keine Wartungsarbeiten selbst
durch. Durch Offnen oder Entfernen wichtiger
Abdeckungen werden spannungsfuhrende Teile
freigelegt, so dass eine erhohte Gefahrdung
besteht. Fur Wartungsarbeiten in diesen
Bereichen ist der Kundendienst zustandig.
1
2
Service
FRANÇAIS
ITALIANO
Maintenance du Moniteur
Manutenzione
Débranchez le moniteur (prise murale)
et contactez un technicien qualifié de
maintenance de ce type d’équipement dans
les cas suivants:
Le cordon d’alimentation ou la prise est
yy
endommagé(e) ou dénudé.
Du liquide a coulé à l’intérieur du moniteur.
yy
Le moniteur a été exposé à la pluie ou à
yy
l’humidité.
Le moniteur ne fonctionne pas normalement
yy
lorsque vous suiv ez les instructions du
mode d’emploi. Ne réglez que les éléments
décrits dans le mode d’emploi. Un Réglage
indadapté d’autres éléments peut entraîner
une déterioration de l’appareil et nécessite
souvent un important travail du technicien
qualifié pour remet tre le moniteur en bon
état de fonctionnement.
Le moniteur est tombé ou son boîtier a été
yy
endommagé.
Le moniteur présente un changement net
yy
dans ses capacités de fonctionnement.
Des bruits secs ou des bruits d’encliquetage
yy
'clic' se font enten dre en continu ou
fréquemment en cours de fonctionnement
du moniteur. Il est normal que certains
moniteurs fassent des bruits occasionnels
lorsqu’ils sont mis sous tension ou hors
tension, ou lors de changements de mode
vidéo.
Ne tentez pas de réparer vous-même votre
moniteur, car ouvrir le moniteur ou retirer son
boîtier peut vous exposer à des décharges
électriques dangereuses et présente par
ailleurs d’autres risques. Pour toute réparation
du moniteur, contactez un technicien qualifié.
Staccare il monitor dalla presa elettrica
e consultare il personale addetto alla
manutenzione quando:
Il cavo elettrico o la spina sono danneggiati
yy
o consumati.
Si è rovesciato del liquido sul monitor.
yy
Il monitor è stato esposto alla pioggia o
yy
all'acqua.
Il monitor non funziona correttamente
yy
secondo le istruzioni oper ative. Regolare
unicamente quei controlli contemplati nelle
istruzioni operative. La manomissione di altri
controlli può provo care danni e spesso poi
è necessario un lungo lavoro da parte dei
tecnici specializzati per ripristinare le normali
funzionalità del monitor.
Il monitor è caduto o si è danneggiata la
yy
struttura.
Il monitor funziona in maniera evidentemente
yy
diversa da prima.vIl monitor lampeggia in
maniera continua o frequente mentre è in
funzione. E' normale che alcuni monitor
emettano suoni occa sionali quando
vengono accesi o spenti, oppure quando si
cam bia la modalità video.
Non cercare di effettuare da soli la
manutenzione poiché l'apertura della struttura
potrebbe esporre l'utente al pericolo di
scariche elettriche o ad altri rischi. Rivolgersi al
personale tecnico qualificato.
Service
ESPANÕL
PORTUGUÊS
Servicio
Manutenção
Desconecte el monitor del tomacorriente de
la pared y refiera el servicio a personal de
servicio calificado cuando:
El cable o enchufe de energía está dañado o
yy
desgastado.
Se ha derramado líquido en el monitor.
yy
El monitor ha sido expuesto a la lluvia o al
yy
agua.
El monitor no funciona normal aunque
yy
se hayan seguido las instrucciones de
operación. Ajuste sólo los controles que
están cubiertos en las instrucciones de
operación. Un ajuste incorrecto de estos
controles pueden causar daño y a veces
requiere de trabajo extenso por un técnico
calificado para restaurar el monitor al
funcionamiento normal.
El monitor se ha dejado caer o el gabinete
yy
se ha dañado.
El monitor exhibe un cambio distinto en la
yy
ejecución.
Los chasquidos o explosivos que emanan
yy
del monitor son continuos o frecuentes
mientras el monitor está operando.
Los ruidos ocasionales son normales para
algunos monitores cuando se prende o se
apaga, o cambia el modo de video.
No trate de arreglar usted mismo el monitor, ya
que abrir y sacar las tapas pueden exponerlo
a niveles de voltaje peligrosos u otros peligros.
Refiera el arreglo a un personal técnico
calificado para ello.
Desligue o monitor da tomada e procure por
serviço autorizado, quando:
O cabo de força ou plugue estiver danificado
yy
ou rompido.
Houve queda de líquido no monitor.
yy
O monitor foi exposto à chuva ou água.
yy
O monitor não opera normalmente seguindo
yy
as instruções de operação. Ajuste somente
os controles descritos nas instruções de
operação. Uma tentativa de ajuste de outros
controles invali-dará a garantia, além de
exigir diversas horas de trabalho de pessoal
qualificado para restaurar as condições
originais de fun-cionamento do monitor.
O monitor caiu ou está com o gabinete
yy
quebrado.
O monitor exibe uma distinta mudança de
yy
performance.
O monitor emite estalos ou estouros
yy
continuamente durante sua operação
normal. Para alguns monitores é normal se
ouvirem estalos quando se liga ou desliga o
monitor ou quando há mudança de modo de
vídeo.
Não tente efetuar a manutenção do monitor
você mesmo. Abrir ou remover as tampas do
gabinete deixarão expostos pontos de alta
tensão em diversas partes do monitor. Procure
sempre pessoal qualificado para execução de
serviços de manutenção.
3
4
Service
NEDERLANDS
РУССКИЙ
Onderhoud
Ремонт и Обслуживание
In de volgende gevallen haalt u de stekker van
de monitor uit het stopcontact en roept u de
hulp in van een gekwalificeerde technicus:
Het netsnoer of de stekker is beschadigd of
yy
versleten.
Er is vloeistof in de monitor gemorst.
yy
De monitor heeft blootgestaan aan regen of
yy
water.
De monitor werk niet goed, ondanks het feit
yy
dat u handelt volgens de gebruiksaanwijzing.
Beperk u bij het instellen van de monitor
tot de items die in de gebruiksaanwijzing
worden besproken. Het onjuist instellen van
andere items kan storingen veroorzaken.
Vaak is dan een omvangrijke reparatie door
een gekwalificeerde technicus nodig, om
de monitor weer voor normaal gebruik in
gereedheid te brengen.
De monitor is gevallen of de behuizing is
yy
beschadigd.
De monitor functioneert wezenlijk anders
yy
dan normaal het geval is.
De monitor produceert voortdurend of
yy
regelmatig kraak- en knalgeluiden. Bij
sommige monitoren is het normaal dat ze
af en toe geluiden produceren bij het in- en
uitschakelen, of wanneer ze veranderen van
videomodus.
Probeer de monitor niet zelf te repareren,
aangezien u bij het openen of verwijderen van
de behuizing blootgesteld kunt worden aan
gevaarlijke elektrische schokken of andere
gevaren. Laat alle reparatiewerkzaamheden
over aan gekwalificeerde technici.
В нижеперечисленных случаях отключите
монитор от сети и обратитесь в пункты
сервисного обслуживания:
Если Вы повредили кабель питания или
yy
вилку.
Если Вы пролили в монитор какую-нибудь
yy
жидкость.
Если монитор подвергся воздействию
yy
воды или дождя.
Если монитор не работает согласно
yy
нормативам, указанным в Инструкции.
При этом используйте для регулировки
только те кнопки управления, которые
предлагаются пользователю в Инструкции.
Неправильное манипулирование другими
кнопками может привести к повреждению
монитора и потребовать дорогостоящего
ремонта.
Если монитор подвергся удару при
yy
падении или если был поврежден его
корпус.
Если в мониторе возникли выраженные
yy
отклонения от нормального режима
работы.
Если монитор издает во время работы
yy
посторонние звуки, хотя для некоторых
типов мониторов включение или
выключение, как правило, сопровождается
какими-либо звуками.
Не пытайтесь проводить самостоятельное
техническое обслуживание монитора. Не
подвергайте себя опасности воздействия
высоких напряжений. Все работы должны
выполняться только квалифицированным
персоналом.
‫‪5‬‬
‫‪Service‬‬
‫العربية‬
‫الخدمة‬
‫افصل الشاشة عن مأخذ الحائط واتصل بفريق خدمة محترف‪:‬‬
‫بال‪.‬‬
‫• إن سلك الطاقة أو المقبس تالف أو ٍ‬
‫• انسكب سائل على الشاشة‪.‬‬
‫• تعرضت الشاشة للمطر أو الماء‪.‬‬
‫بشكل طبيعي باتباع اإلرشادات التالية‪ .‬اضبط‬
‫• ال تعمل الشاشة‬
‫ٍ‬
‫عناصر التحكم المذكورة في إرشادات التشغيل فقط‪ .‬إذ قد يؤدي‬
‫الضبط غير الصحيح لبعض عناصر التحكم إلى إلحاق الضرر وغالباً‬
‫ً‬
‫عمال شاقاً من تقني محترف إلعادة الشاشة إلى وضع‬
‫ما قد يتطلب‬
‫التشغيل العادي‪.‬‬
‫• وقعت الشاشة أو قد تم إتالف الصندوق‪.‬‬
‫• أداء الشاشة متغيّر بشكل واضح‪.‬‬
‫بشكل متواصل أو متكرر‬
‫• تصدر الشاشة صوت طقطقة أو فرقعة‬
‫ٍ‬
‫أثناء التشغيل‪.‬‬
‫من الطبيعي أن تصدر بعض الشاشات أصواتاً مؤقتة عند تشغيلها أو‬
‫إيقاف تشغيلها‪ ،‬أو عند تغيير أوضاع الفيديو‪.‬‬
‫ال تحاول صيانة الشاشة بنفسك‪ ،‬إذ قد يعرضك فتح الغطاء أو إزالته‬
‫لفولتية خطيرة أو غيرها من المخاطر‪.‬‬
‫خصص أعمال الخدمة والصيانة لفريق الخدمة المحترف‪.‬‬
‫‪Maintenance Tel‬‬
‫‪8339561‬‬
‫‪Dammam‬‬
‫‪8942694‬‬
‫‪Khobar‬‬
‫‪5861262‬‬
‫‪Hoffuf‬‬
‫‪3624444‬‬
‫‪Jubail‬‬
‫‪4652641‬‬
‫‪Riyadh‬‬
‫‪6531688‬‬
‫‪Jeddah‬‬
‫‪5500110‬‬
‫‪Makkah‬‬
‫‪8274793‬‬
‫‪Madina‬‬
6
Service
日本語
한국어
保守および修理
수리
次のような保守になったら、モニタ-の電源プラグ
をコンセントから抜き、修理センターにご相談くださ
い。
電源コードまたはプラグが破損した、または擦り
yy
切れた。
モニターの内部に液体をこぼしてしまった。
yy
モニターが雨または水に濡れてしまった。
yy
取扱説明書どおりに操作してもモニターにうまく
yy
画像が表示されない場合、お客様の方で調整
するのは、取扱 説明書で説明されているボタン
を使った調整だけにしてください。
モニターを床に落としてしまった。または、キャビ
yy
ネットを破損してしまった。
モニターの性能が明らかに落ちてきた。
yy
モニターも使用中、常にまたは断続的にピシピ
yy
シといった音やパンといった音がする。ただし、
正常な モニターでも、電源を入れたりきったりし
たときには音はする場合があります。
モニターのカバーを開いたり取り外したりすると、高
電圧による感電その他の危険性があるので、モニ
ターを自分で修理したりしないでください。修理が
必要なときは、サービスマンに頼んでください。
警告
ディスプレイの裏ぶたを開け
ないでください。内部には高
電圧の部分があり、感電の恐
れがあります。
*お問い合わせ先については提供されている「修理に
関するご案内」カードのサービスセンター案内をご参
照ください。
다음과 같은 경우에는 벽면 콘센트에서 모니터의 플러그
를 뺀 다음 자격이 있는 수리 담당자에게 의뢰하십시오 .
전원코드 또는 플러그가 손상되거나 낡았습니다 .
yy
액체가 엎질러져서 모니터에 흘러들어갔습니다 .
yy
모니터가 비 또는 물에 노출되었습니다 .
yy
모니터가 일반적인 동작지침에 맞게 동작하지 않으며 ,
yy
동작지침에 설명된 컨트롤만 조정합니다 . 다른컨트롤
을 잘못 조정하여 손상된 것 같습니다 . 모니터가 정상
적으로 동작하도록 복원하려면 자격을 갖춘 기술자가
전반적으로 수리해야 합니다 .
모니터를 떨어뜨렸거나 캐비닛이 손상되었습니다 .
yy
모니터의 성능이 눈에 띄게 달라졌습니다 .
yy
모니터가 작동하는 동안 모니터에서 스냅 또는 팝 현
yy
상이 계속적으로 또는 자주 발생합니다 . 모니터를 켜
거나 끌 때 또는 비디오 모드를 변경할 때 일부 모니
터에서 소리가 나는 경우가 있는데 이는 정상적인 것
입니다 .
덮개를 열거나 떼어내는 것은 감전의 우려 및 다른 위험
요소가 있으므로 모니터를 직접 수리하려고 하지 마십시
오.
모든 수리는 자격을 갖춘 수리 담당자에게 의뢰하십시오 .
Energy saving Design
ENGLISH
PORTUGUÊS
Energy Saving Design
Programa de economia de energia
This program is designed to have computer
equipment manufacturers build circuitry into
their products to reduce power consumption
when it is not in operation.
When this monitor is used with a PC on
which a screen blanking software complying
with the VESA Display Power Management
Signalling (DPMS) Protocol is installed, it can
conserve significant energy by reducing power
consumption when it is not in operation.
There are 2 signal lines, 3 modes of operation.
: On Mode, Sleep Mode, Off Mode.
Mode
Definition
On
mode
The normal operation.
When the monitor is on mode,
being connected to a power
source, it displays an image.
Sleep
Mode
The reduced power state.
returns to on mode when the
user moves the mouse or
presses a key on the keyboard.
Off
Mode
The lowest power consumption
state.
returns to on mode when the
user pushes a power switch.
Este programa foi elaborado com a finalidade
de estimular os fabricantes de equipamentos
para computadores a construírem em seus
produtos sistemas que reduzam o consumo de
energia quando eles não estiverem em uso.
Quando este monitor for utilizado com um
computador cujo software de proteção de
tela estiver instalado, em conformidade com
o protocolo de gerenciamento de energia
Display Power Management Signalling (DPMS)
VESA, pode haver uma considerável economia
de energia pela redução do consumo elétrico
em momentos de ociosidade.
Existem duas linhas de sinal e três modos de
operação: Ativado (On), em espera (Sleep) e
desativado (Off).
Modo
Ligado
A operação normal.
Quando o monitor estiver
ativado e conectado a uma
fonte de alimentação, será
exibida uma imagem.
Em
espera
Estado de baixa energia.
Retorna ao modo ativado
quando o usuário move o
mouse ou pressiona uma tecla
no teclado.
Desativado
O estado de menor consumo de
energia.
Retorna ao modo ativado
quando o usuário pressiona
algum botão liga/desliga.
Note
• The energy saving Design monitors only work
while connected to the computers that have
energy saving features.
Definição
Observação
•Os monitores que incorporam o programa
de economia de energia só funcionam
apropriadamente se conectados a
computadores que possuem recursos de
economia de energia.
1
2
Energy saving Design
한국어
DEUTSCH
절전디자인
Energiespar-Design
이 프로그램은 컴퓨터 장비 제조업체가 해당 제품에
회로를 내장하여 , 사용하지 않는 기간에 전력 소비를
줄일 수 있도록 만들어졌습니다 .
이 모니터를 VESA DPMS(Display Power
Management Signaling) 프로토콜을 준수하는
화면 비움 소프트웨어가 있는 PC 와 함께 사용하면
사용하지 않는 기간에 전력 소비를 줄여서 에너지를
상당히 절약할 수 있습니다 .
두 개의 신호 라인과 세개의 동작모드 [ 온 모드 , 절전
모드 , 오프 모드 ) 가 존재합니다 .
모드
정의
온 모드
정상적인 동작상태 .
전원에 연결되어 있고 스크린에 정상
적인 이미지를 표시하고 있다 .
절전
모드
컴퓨터로 부터 지시를 받은 후 또는
기타 기능에 의해 모니터의 전력이 저
감되는 상태 . 이 모드에서는 스크린
에 아무 것도 표시되지 않으며 , 사용
자 또는 컴퓨터로 부터의 지령 ( 마우
스 동작 , 키보드 입력 ) 에 의해 가동
상태인 온 모드로 전환 된다 .
오프
모드
가장 낮은 전력 소비 상태 .
전원 스위치를 이용해 전원을 오프시
킨 상태이다 .
Dieses Programm wurde konzipiert, um
die Hersteller von Computergeräten zu
veranlassen, Schaltungen in ihre Produkte
einzubauen, die zu einem geringeren
Stromverbrauch führen, wenn das Gerät nicht
in Betrieb ist.
Wenn dieser Bildschirm zusammen mit einem
PC verwendet wird, auf dem eine Software zur
Abschaltung des Bildschirms installiert ist, die
dem VESA Display Power Management
Signalling (DPMS)-Protokoll entspricht, kann
er erheblich Energie sparen, indem er den
Stromverbrauch reduziert, wenn er nicht in
Betrieb ist.
Es gibt 2 Signalleitungen, 3 Betriebsmodi:
Ein Modus, Ruhemodus, Aus Modus.
Modus
Ein
Modus
Der normale Betrieb.
Wenn der Bildschirm im
Ein Modus ist, zeigt er ein
Bild an, sofern er mit einer
Stromquelle verbunden ist.
Ruhemodus
Der reduzierte
Energiezustand.
Kehrt in den Ein Modus
zurück, sobald der Benutzer
die Maus bewegt oder eine
Taste auf der Tastatur drückt.
Aus
Modus
Der Zustand, in dem am
wenigsten Energie verbraucht
wird.
Kehrt in den Ein Modus
zurück, sobald der Benutzer
einen Stromschalter drückt.
참고
•
모니터 절전 기능은 절전 기능이 있는 컴퓨터
에 연결되어 있는 경우에만 사용할 수 있습니
다.
Definition
Hinweis:
• Die Bildschirme mit Energiespar-Design
funktionieren nur, wenn sie an Computer mit
Energiesparfunktionen angeschlossen sind.
Energy saving Design
MAGYAR
BAHASA INDONESIA
Energiatakarékos kialakítás
Desain Hemat Energi
E program célja, hogy a számítógéptartozékgyártók azon termékei, amelyek rendelkeznek
az ehhez szükséges áramkörrel, alacsony
fogyasztással üzemeljenek akkor, amikor
nincsenek használatban.
Ha ezt a monitort olyan számítógéppel
használja, amelyen VESA képerny+tápellátáskezel+ jelrendszer (DPMS) protokollt támogató
képerny+kikapcsoló szoftver van, jelent+s
mennyiség energiát takaríthat meg az
áramfelvétel használaton kívüli állapotban való
csökkentésével.
2 jelvonal van 3 m ködési móddal:
Bekapcsolt mód, Alvás mód, Kikapcsolt mód.
Mód
Leírás
Bekapcsolt
mód
Ez a normál m ködés módja.
Amikor a monitor
bekapcsolt módban van,
és áramforráshoz van
csatlakoztatva, egy képet
jelenít meg.
Alvás
mód
Ez a csökkentett
áramfelvétel állapot.
A bekapcsolt módba az egér
mozgatásával vagy egy
billenty lenyomásával térhet
vissza.
Kikapcsolt
mód
Megjegyzés
A legkisebb fogyasztással
járó állapot.
A bekapcsológomb
megnyomásával térhet
vissza a bekapcsolt
állapotba.
• Az energiatakarékos kialakítással készült
monitorok csak akkor m ködnek, ha olyan
számítógépre csatlakoztatja, amely rendelkezik
energiatakarékossági funkciókkal.
Program ini dirancang agar produsen peralatan
komputer membangun sistem sirkuit ke dalam
produk mereka untuk mengurangi konsumsi
daya saat peralatan sedang tidak beroperasi.
Saat monitor ini digunakan dengan komputer
PC di mana perangkat lunak pengosong layar
yang sesuai dengan Protokol Display Power
Management Signalling (DPMS) terinstal,
monitor dapat menghemat energi secara
signifikan dengan mengurangi konsumsi daya
saat sedang tidak beroperasi.
Terdapat 2 saluran sinyal, 3 mode operasi:
Mode On (Menyala), Mode Sleep (Tidur),
Mode Off (Mati).
Mode
Definisi
Mode
On
Operasi normal.
Saat monitor berada dalam
mode on, terhubung dengan
sumber daya, monitor
menampilkan gambar.
Mode
Sleep
Keadaan dengan daya yang
dikurangi.
kembali ke mode on saat
pengguna menggerakkan
mouse atau menekan tombol
pada keyboard.
Mode
Off
Keadaan dengan konsumsi
daya terendah.
kembali ke mode on saat
pengguna menekan tombol
daya.
Catatan
• Monitor dengan desain hemat energi hanya
bekerja ketika terhubung dengan komputer
yang memiliki fitur hemat energi.
3
4
Energy saving Design
日本語
ESPAÑOL
省エネ設計
(省エネルギー設計、節電設計)
Diseño de ahorro de energía
本プログラムはコンピュータ機器メーカーが製造す
る製品がその非使用時 ( 非動作時 ) は消費電力
を抑える回路構成を持つことを目的に策定されま
した。
本モニターを VESA が策定した DPMS(Display
Power Management Signaling) プロトコルに凖拠し
た スクリーンブランキング(スクリーンセーバー)ソ
フトウェアをインストールした PC と一緒にご使用す
ることで、本モニターの非使用時(非動作時)の消
費電力を大幅に抑えることができます。
2 つの信号ラインと、3 つの操作モードがあります。
操作モードはオンモード、スリープモード、そして
オフモードの3つです。
モード
説明
オン モ
ード
通常の使用時 ( 通常の動作時)
モニターがオンモードで電源は
接続されているとき画像が表示さ
れます。
スリープモ
ード
省電力の状態です。
マウスを働かすかキーボードー
のどれかのキ-を押すとオンモ
ードに戻ります。
オフ モ
ード
最も消費電力が少ない状態です。
電源スイッチを入れるとオンモー
ドに戻ります。
注 ( ご注意 )
Este programa está diseñado para que los
fabricantes de equipos informáticos incorporen
sistemas de circuitos a sus productos con el
fin de reducir el consumo de energía cuando
no esté funcionando el aparato.
Cuando este monitor se utiliza con un PC en
el que esté instalado un software de apagado
de pantalla que cumpla con el protocolo DPMS
(Display Power Management Signalling –
señalización de la gestión de la energía de la
pantalla) de VESA, se puede ahorrar una
importante cantidad de energía reduciendo su
consumo cuando no se utiliza.
Hay 2 líneas de señal y 3 modos de
funcionamiento:
Modo Encendido, Modo Desconexión
automática, Modo Apagado
Modo
Definición
Modo
Encendido
Funcionamiento normal.
Cuando el monitor se
encuentra en el modo
encendido, si está
conectado a la corriente,
muestra una imagen.
Modo
Desconexión
automática
Estado de uso reducido de
energía.
Vuelve al modo encendido
cuando el usuario mueve el
ratón o pulsa una tecla del
teclado.
Modo
Apagado
El estado de menor
consumo de energía.
Vuelve al modo encendido
cuando el usuario pulsa el
interruptor.
• 省電力設計のモニターは省電力機能を備えたコン
ピュータに接続されたときのみ有效です。
Nota
• Los monitores con diseño de ahorro de energía
sólo funcionan cuando están conectados a
ordenadores con capacidad de ahorro de
energía.
Energy saving Design
ҚАЗАҚША
NEDERLANDS
Энергия үнемдейтін дизайн
Energiebesparend ontwerp
Бұл бағдарлама компьютер жабдықтарын
өндірушілерге жұмыс істемей тұрғанда,
қуаттың тұтынылуын азайту мақсатымен
өнімдеріне электр схемасын енгіздіруге
арналған.
Монитор VESA DPMS протоколына сәйкес
келетін экранды жабу бағдарламалық
құралы орнатылған компьютермен
пайдаланылса, ол жұмыс істемей тұрғанда,
қуаттың тұтынылуын азайтып, энергияның
едәуір мөлшерін сақтайды.
Жұмыстың 2 сигналдық желісі мен 3 режимі
бар :
Қосу режимі, Күту режимі, Өшіру режимі.
режимі
Анықтама
Қосу
режимі
Қалыпты жұмыс
Монитор қуат көзіне
жалғанып, қосу режимінде
тұрғанда, онда сурет
көрсетіледі.
Күту
режимі
Пайдаланушы тінтуірді
жылжытқанда немесе
пернетақтадағы бір пернені
басқанда, азайтылған
қуат күйі қосу режиміне
қайтады.
Өшіру
режимі
Пайдаланушы қуат
қосқышын басқанда,
қуатты тұтынудың ең
төменгі күйі қосу режиміне
қайтады.
Ескертпе
• Энергия үнемдейтін дизайнды мониторлар
энергияны үнемдеу мүмкіндіктері бар
компьютерлерге қосылып тұрғанда ғана
жұмыс істейді.
Dit programma stimuleert fabrikanten van
computerapparatuur om schakelingen in
producten te bouwen die het stroomverbruik
verminderen als de apparatuur niet wordt
gebruikt.
Als deze monitor wordt gebruikt in combinatie
met een pc waarop schermuitschakelsoftware
is geïnstalleerd die compatible is met het
VESA Display Power Management Signallingprotocol (DPMS), kunt u aanzienlijk veel
energie besparen door het stroomverbruik te
verminderen als de monitor niet wordt gebruikt.
Er zijn 2 signaallijnen en 3 bedrijfsmodi:
de aan modus, de slaapmodus en de uit
modus.
Modus
Definitie
Aan
modus
De normale bedrijfsmodus.
Als de monitor in aan modus
staat en op een stroombron
wordt aangesloten, wordt
er beeld weergegeven.
Slaapmodus
De stand voor minder
stroomverbruik.
Keert terug naar aan modus
als de gebruiker de muis
beweegt of een toets op het
toetsenbord indrukt.
Uit modus
De stand voor het laagste
stroomverbruik.
Keert terug naar aan
modus als de gebruiker een
stroomschakelaar indrukt.
Opmerking
• Monitors met een energiebesparend ontwerp
werken alleen als ze worden aangesloten op
computers met energiebesparende functies.
5
6
Energy saving Design
FRANÇAIS
ΕΛΛΗΝΙΚΆ
Design d’économie d’énergie
Σχεδίαση εξοικονόμησης ενέργειας
Ce programme est conçu pour obtenir
l’installation de circuits par les fabricants
d’équipements informatiques dans leurs
produits afin de réduire la consommation en
courant de ces derniers lorsqu’ils ne sont pas
en fonctionnement
Το πρόγραμμα αυτό έχει σχεδιαστεί ώστε οι
κατασκευαστές εξοπλισμού ηλεκτρονικών
υπολογιστών να δημιουργούν τη διάταξη των
κυκλωμάτων στα προϊόντα τους με τέτοιο
τρόπο ώστε να μειώνεται η κατανάλωση
ενέργειας όταν βρίσκονται εκτός λειτουργίας.
Lorsque ce moniteur est utilisé avec un PC
sur lequel est installé un logiciel d’effacement
d’écran conforme au protocole DPMS VESA
(Display Power Management Signalling), il
peut économiser une énergie significative en
réduisant la consommation de courant lorsqu’il
n’est pas en fonctionnement.
Όταν η οθόνη αυτή χρησιμοποιείται με
υπολογιστή, στον οποίο έχει εγκατασταθεί
λογισμικό κενής οθόνης που συμμορφώνεται
με το πρωτόκολλο Display Power Management
Signalling (DPMS - Σηματοδότηση διαχείρισης
ενέργειας οθόνης) της VESA, μπορεί να
επιτύχει σημαντική εξοικονόμηση ενέργειας
μειώνοντας την κατανάλωση ρεύματος όταν
βρίσκεται εκτός λειτουργίας.
Il dispose de 2 lignes de signaux et de 3
modes de fonctionnement :
Mode activé (On), mode de veille (Sleep),
mode désactivé (Off).
Mode
Définition
Mode
activé (On)
Le fonctionnement normal.
Lorsque le moniteur est en
mode activé, étant connecté
à une source d’alimentation,
il affiche une image.
Mode de
veille
(Sleep)
L’état d’alimentation réduit.
Le moniteur retourne
au mode activé lorsque
l’utilisateur déplace la souris
ou appuie sur une touche
sur le clavier.
Mode
désactivé
(Off)
L’état d’alimentation en
énergie le plus faible.
Le moniteur retourne
au mode activé lorsque
l’utilisateur appuie sur un
interrupteur marche/arrêt.
Note
• Les moniteurs design économiques en énergie
fonctionnent uniquement lorsqu’ils sont
connectés à des ordinateurs disposant de
fonctionnalités d’économie d’énergie.
Υπάρχουν 2 γραμμές σήματος, 3 τρόποι
λειτουργίας :
Σε λειτουργία, Σε αδράνεια, Εκτός λειτουργίας.
Λειτουργία
Σε
λειτουργία
Σε
αδράνεια
Εκτός
λειτουργίας
Ορισμός
Η κανονική λειτουργία
Όταν η οθόνη βρίσκεται
σε λειτουργία και είναι
συνδεδεμένη με μια πηγή
τροφοδοσίας, εμφανίζεται
εικόνα.
Όταν η οθόνη βρίσκεται
σε κατάσταση μειωμένης
ενέργειας και ο χρήστης
μετακινεί το ποντίκι ή
πατάει κάποιο πλήκτρο στο
πληκτρολόγιο, τότε η οθόνη
επιστρέφει σε λειτουργία.
Όταν η οθόνη βρίσκεται σε
κατάσταση χαμηλότερης
κατανάλωσης ενέργειας και ο
χρήστης πατάει το διακόπτη
λειτουργίας, τότε η οθόνη
επιστρέφει σε λειτουργία.
Σημείωση
• Οι οθόνες με σχεδίαση εξοικονόμησης ενέργειας
λειτουργούν μόνο όταν είναι συνδεδεμένες
με υπολογιστές που διαθέτουν δυνατότητες
εξοικονόμησης ενέργειας.
Energy saving Design
7
УКРАЇНСЬКА
ITALIANO
Програма енергозбереження
Programma di risparmio energetico
Ця програма має на меті стимулювати
виробників комп'ютерного обладнання
до впровадження у своїх виробах засобів
зменшення енергоспоживання під час
простою.
Якщо на підключеному персональному
комп'ютері встановлено програмне
забезпечення вимкнення екрана, сумісне з
протоколом сигналів керування живленням
дисплея VESA DPMS, цей монітор
забезпечує суттєву економію електроенергії
за рахунок зниження енергоспоживання в
той час, коли ним не користуються.
Передбачено 2 сигнальні лінії та 3 режими
роботи:
"ввімкнено", "очікування" та "вимкнено".
Режим
Пояснення
Режим
"увімкнено"
Звичайний режим роботи
виробу.
Коли монітор підключений
до джерела живлення
і ввімкнений, на
екрані відображається
зображення.
Режим
очікування
Режим
"вимкнено"
У цьому режимі монітор
споживає менше
електроенергії. З нього
можна повернутися в
режим "увімкнено" порухом
мишки або натисненням
будь-якої клавіші на
клавіатурі.
У цьому режимі
енергоспоживання
монітора мінімальне. З
нього можна повернутися
в режим "увімкнено"
натисненням кнопки
живлення на моніторі.
Примітка
• Функція енергозбереження монітора
працюватиме лише за умови наявності
відповідної функції на під'єднаному
комп'ютері.
Questo programma è stato messo a punto
affinché i produttori di computer producano
circuiti per i loro prodotti in grado di limitare
il consumo energetico quando non sono in
funzione.
Quando questo monitor viene utilizzato
con un PC su cui è installato un software
per l'annullamento dello schermo conforme
al protocollo VESA DPSM (Display Power
Management Signalling), è in grado di
risparmiare una quantità significativa di energia
riducendo il consumo quando non è in fuzione.
Sono disponibili 2 linee di segnale, 3 modalità
operative:
Modalità On, modalità Sleep, modalità Off.
Modalità
Definizione
Modalità
On
Funzionamento normale.
Quando il monitor si trova in
modalità On ed è connesso a
una sorgente elettrica, viene
visualizzata un'immagine.
Modalità
Sleep
Stato di consumo energetico
ridotto.
Torna alla modalità On
quando l'utente sposta il
mouse o preme un tasto
sulla tastiera.
Modalità
Off
Stato di consumo energetico
ridotto al massimo.
Torna alla modalità On
quando l'utente premere un
interruttore.
Nota
• I monitor conformi al Programma di risparmio
energetico funzionano solo se connessi a
computer dotati di funzionalità di risparmio
energetico.
8
Energy saving Design
РУССКИЙ
POLSKI
Функция сохранения энергии
Oszczdzanie energii
Эта программа разработана для создания и
внедрения производителями компьютерного
оборудования схем, позволяющих снизить
потребление электроэнергии, когда
компьютер не находится в рабочем режиме.
Ten program został stworzony, aby producenci
sprztu komputerowego mieli moliwoć
wbudowania do swoich produktów zespołów
obwodów elektrycznych redukuj"cych pobór
mocy w stanie bezczynnoci.
Если монитор используется с ПК, на котором
установлено программное обеспечение
для затемнения экрана, соответствующее
протоколу VESA Display Power Management
Signalling (DPMS), он может экономить
энергию, сокращая ее потребление, когда
не находится в рабочем режиме.
W przypadku uycia tego monitora na
komputerze osobistym (PC), na którym
zainstalowano oprogramowanie wygaszaj"ce
ekran zgodne z protokołem VESA (DPMS –
Display Power Management Signallising),
umoliwia on zaoszczdzanie znacznych iloci
energii poprzez redukcj poboru mocy w stanie
bezczynnoci.
Существуют 2 сигнальные линии, 3 режима
работы:
Включен, Ожидание, Выключен
Режим
Описание
Включен
Обычный режим работы.
Когда монитор подключен
к источнику питания и
находится в режиме
«Включен», он выводит
изображение на экран.
Ожидание
Энергопотребление
снижено. Компьютер
возвращается в режим
«Включен», когда
пользователь перемещает
мышь или нажимает
любую клавишу на
клавиатуре.
Выключен
Энергопотребление
минимально. Компьютер
переходит в режим
«Включен», когда
пользователь нажимает
кнопку включения
питания.
Примечание
• Мониторы с функцией сохранения энергии
работают только при соединении с
компьютерами, поддерживающими эту
функцию.
Istniej" 2 linie sygnału, 3 tryby pracy:
Wł"czony, Upienie, Wył"czony.
Tryb
Definicja
Wł"czony
Normalny proces działania.
W trybie „wł"czony” monitor
podł"czony jest do 8ródła
zasilania i wywietla obraz.
Upienie
Wył"czony
Uwaga
Stan zredukowanego
poboru mocy.
Przywraca do stanu
„wł"czony”, gdy uytkownik
poruszy myszk" lub
przycinie dowolny klawisz
na klawiaturze.
Stan najmniejszego poboru
mocy.
Przywraca do stanu
„wł"czony”, gdy
uytkownik nacinie wł"cznik
zasilania.
• Monitory z funkcj" oszczdzania energii działaj"
tylko, jeli s" podł"czone do komputerów
posiadaj"cych właciwoci oszczdzania energii.
‫‪9‬‬
‫‪Energy saving Design‬‬
‫العربية‬
‫‪繁體中文‬‬
‫‪節能設計‬‬
‫تصميم موفر للطاقة‬
‫تم إعداد هذا البرنامج بحيث تتمكن شركات تصنيع أجهزة الكمبيوتر‬
‫من إدماج مجموعة دارات إلكترونية في منتجاتها للحد من استهالك‬
‫الطاقة عند عدم تشغيل المنتج‪.‬‬
‫فعند استخدام هذه الشاشة مع جهاز كمبيوتر عليه برنامج الشاشة‬
‫الفارغة المتوافق مع بروتوكول بث إشارات إدارة طاقة الشاشة‬
‫(‪ )DPMS‬المثبت وفق معايير ‪ ،VESA‬قد توفر حجماً كبيراً من‬
‫الطاقة من خالل الحد من استهالك الطاقة عند عدم تشغيلها‪.‬‬
‫يتوفر خطا إشارة‪ ،‬وثالثة أوضاع تشغيل‪.‬‬
‫‪ :‬وضع التشغيل‪ ،‬ووضع السكون‪ ،‬ووضع إيقاف التشغيل‪.‬‬
‫وضع‬
‫التعريف‬
‫وضع التشغيل‬
‫التشغيل العادي‬
‫تعرض الشاشة صورة عندما تكون في‬
‫وضع التشغيل ومتصلة بمصدر طاقة‪.‬‬
‫وضع السكون‬
‫تعود حالة توفير الطاقة إلى وضع التشغيل‬
‫عندما يحرك المستخدم الماوس أو يضغط‬
‫على أي مفتاح على لوحة المفاتيح‪.‬‬
‫وضع إيقاف‬
‫التشغيل‬
‫تعود حالة استهالك الطاقة األدنى إلى وضع‬
‫التشغيل عندما يضغط المستخدم على مفتاح‬
‫الطاقة‪.‬‬
‫مالحظة‬
‫• تعمل الشاشات ذات التصميم الموفر للطاقة فقط عند‬
‫توصيلها بأجهزة الكمبيوتر المزودة بميزات توفير الطاقة‪.‬‬
‫‪此程式用於幫助電腦設備製造廠商在他們的產‬‬
‫‪品中建立電路,藉此降低產品處於非作業狀態‬‬
‫‪時的功率‬‬
‫。‪消耗量‬‬
‫‪本顯示器與已安裝符合 VESA 顯示能源管理訊‬‬
‫‪號 (DPMS) 協定之螢幕抑制顯示軟體的電腦配‬‬
‫‪合使用時,可降低處於非作業狀態時的功率消‬‬
‫。‪耗量,進而節省大量能源‬‬
‫‪共有 2 根訊號線以及 3 種作業模式:‬‬
‫。‪開啟模式、睡眠模式和關閉模式‬‬
‫‪定義‬‬
‫‪模式‬‬
‫。‪正常作業模式‬‬
‫‪顯示器與電源連接並處於開‬‬
‫。‪啟模式時,會顯示影像‬‬
‫‪開啟模式‬‬
‫。‪低功率消耗狀態‬‬
‫‪若使用者移動滑鼠或按鍵盤‬‬
‫。‪上的鍵,則返回開啟模式‬‬
‫‪睡眠模式‬‬
‫。‪最低功率消耗狀態‬‬
‫‪若使用者按電源開關,則返‬‬
‫。‪回開啟模式‬‬
‫‪關閉模式‬‬
‫‪註‬‬
‫‪•該節能設計顯示器僅在連接至具有節能功能的電‬‬
‫。‪腦時才能發揮其節能作用‬‬
DDC(Display Data Channel)
ENGLISH
DEUTSCH
DDC (Display Data Channel)
DDC (Display Data Channel)
DDC is a communication channel over which
the monitor automatically informs the host
system (PC) about its capabilities.
DDC protocol
① DDC1/DDC2B
An uni-directional communication channel.
② DDC 2AB/DDC2B+/DDC2Bi
A bi-directional communication channel.
Note
• PC must support DDC functions to do this.
E-DDC (Enhanced DDC)
A protocol based on I²C and used on a bidirectional data channel between the display
and host. This protocol accesses devices at I²C
address of A0/A1 as well as the address 60.
The 60 address is used as a segment register
to allow larger amounts of data to be retrieved
than is possible using DDC2B protocols. The
protocol is compatible with DDC2B protocols.
DDC ist ein Kommunikationskanal, über
weiche Sie von lhrem Monitor automatisch
über das verbundene System (PC) und seine
Fähigkeiten informiert werden.
DDC Protokoll
① DDC1/DDC2B
Ein unidirektionaler Kommunikationskanal.
② DDC 2AB/DDC2B+/DDC2Bi
Ein bidirektionaler Kommunikationskanal.
Anmerkung
• Der PC muß für DDC Funktionen eingerichtet
sein.
E-DDC (Erweitertes DDC)
Ein Protokoll, das auf I2C basiert und in einem
bidirektionalen Datenkanal zwischen Anzeige
und Host eingesetzt wird. Dieses Protokoll
greift an der I2C-Adresse von A0/A1 und an
der Adresse 60 auf Gerate zu. Die Adresse 60
dient als Segmentregister und ermoglicht den
Abruf von großeren Datenmengen als mit den
DDC2B-Protokollen. Das Protokoll ist mit den
DDC2B-Protokollen kompatibel.
1
2
DDC(Display Data Channel)
FRANÇAIS
ITALIANO
DDC (Display Data Channel)
DDC (Display Data Channel)
DDC est une chaine de communication par
le biais de laquelle le moniteur prévient
automatiquement le systéme central (PC) de
ces capacités.
Protocole DDC
① DDC1/DDC2B
Canal de communication unidirectionnel.
② DDC 2AB/DDC2B+/DDC2Bi
Canal de communication bidirectionnel.
Remarque
• Le PC doit posséder les fonctions DDC
pour cela.
E-DDC (Commande numérique
directe (DDC) optimisée)
Protocole fondé sur l’I²C et appliqué à
un canal bi-directionnel de transmission
de données placé entre l’écran et l’hôte.
Ce protocole accède aux périphériques à
l’adresse I²C de A0/A1 ainsi qu’à l’adresse
60. L’adresse 60 est utilisée comme
registre de segment afin d’obtenir des
quantités de données supérieures à ce
que permettent les protocoles DDC2B.
Ce protocole est compatible avec les
protocoles DDC2B.
Il DDC è un canale di comunicazione attraverso
il quale il monitor informa automaticamente il
sistema ospite (PC) circa le proprie capacità.
Protocollo DDC
① DDC1/DDC2B
Un canale di comunicazione uni-direzionale.
② DDC 2AB/DDC2B+/DDC2Bi
Un canale di comunicazione bi-direzionale.
Nota
• Per fare questo il PC deve supportare le
funzioni DDC.
E-DDC (DDC potenziato)
Protocollo basato su I²C e utilizzato su un
canale dati bidirezionale tra monitor e host.
Questo protocollo accede a dispositivi con
indirizzo I²C di A0/A1 nonche all'indirizzo 60.
L'indirizzo 60 viene utilizzato come registro di
segmento per consentire di recuperare quantita
di dati superiori rispetto a quanto e possibile
utilizzando i protocolli DDC2B. Il protocollo e
compatibile con i protocolli DDC2B.
DDC(Display Data Channel)
ESPANÕL
PORTUGUÊS
DDC (Canal de despliegue de
información)
DDC (Display Data Channel)
DDC es un canal de comunicacion sobre el
cual el monitor automáticamente informa al
sistema anfitrión (PC) sobre sus capacidades.
Protocolo DDC
① DDC1/DDC2B
Un canal de comunicación unidireccional.
② DDC 2AB/DDC2B+/DDC2Bi
Un canal de comunicación bidireccional.
Nota
• La PC debe soportar las funciones DDC para
poder hacer esto.
E-DDC (DDC mejorado)
Un protocolo que se basa en I²C y se usa en
un canal de datos bidireccional entre el monitor
y el sistema host. Este protocolo
accede a los dispositivos en la direccion I²C
de A0/A1, asi como en la direccion 60. La
direccion 60 se usa como un registro de
segmentos para poder recuperar mas cantidad
de datos de lo que es posible mediante los
protocolos DDC2B. El protocolo es compatible
con protocolos DDC2B.
DDC é um canal de comunicação através
do qual o monitor informa ao computador
a respeito de suas características.DDC
Protokoll
① DDC1/DDC2B
Um canal de comunicação unidirecional.
② DDC 2AB/DDC2B+/DDC2Bi
Um canal de comunicação bidirecional.
Ovservação
• O PC deve suportar DDC para fazer isso.
E-DDC (DDC Aperfeicoado)
Um protocolo com base em I²C que e utilizado
em um canal de dados bidirecional entre
o monitor e o host. Este protocolo acessa
dispositivos no endereco I²C do A0/A1 assim
como no endereco 60. O endereco 60 e
utilizado com um registro de segmento que
permite que maiores quantidades de dados
sejam recuperados que quando se utiliza os
protocolos DDC2B. O protocolo e compativel
com os protocolos DDC2B.
3
4
DDC(Display Data Channel)
NEDERLANDS
РУССКИЙ
DDC (Display Data Channel)
Канал обмена данных между
монитором и компьютером
DDC.
DDC is een communicatiekanaal waarmee de
monitor het hostsysteem (PC) automatisch
informeert over zijn mogelijkheden.
DDC-protocol
① DDC1/DDC2B
Een unidirectioneel communicatiekanaal.
② DDC 2AB/DDC2B+/DDC2Bi
Een bidirectioneel communicatiekanaal.
OPMERKING
• Dit kan alleen als de PC DDC ondersteunt.
E-DDC (Uitgebreide DDC)
Een op I²C gebaseerd protocol dat
wordt gebruikt op een gegevenskanaal
in twee richtingen, tussen het scherm
en de host. Dit protocol geeft toegang
tot apparatuur met A0/A1 en 60 als I²Cadres. Het adres 60 wordt gebruikt
als een segmentregister waarmee in
vergelijking met DDC2Bprotocollen grotere
hoeveelheden gegevens kunnen worden
gezocht. Het protocol is compatible met
DDC2B-protocollen.
DDC-канал связи, по которому монитор
автоматически информирует компьютер о
своих возможностях.
Протокол DDC
① DDC1/DDC2B
Односторонний канал связи
② DDC 2AB/DDC2B+/DDC2Bi
Двусторонний канал связи.
ПРИМЕЧАНИЕ
• Примечание: Для работы в этом режиме
необходимо загрузить соответствующий
драйвер компьютера.
E-DDC (Расширенный канал
передачи данных)
Протокол, основанный на технологии I2C,
который используется для двусторонней
передачи данных между дисплеем и
источником видеоданных. Для доступа к
устройствам используются биты адреса I2C
(А0/А1), а также адрес 60.
Адрес 60 указывает на регистр сегментов,
который позволяет получать большие
объемы данных, чем при использовании
протокола DDC2B. Этот протокол совместим
с протоколами DDC2B.
DDC(Display Data Channel)
한국어
日本語
DDC( 디스플레이 데이터 채널 )
DDC(ディプレイ • データ • チャンネル)
DDC 는 모니터의 기능에 관한 정보를 자동으로 호스
트 시스템 (PC) 에 제공하는 통신 채널입니다
DDC protocol
① DDC1/DDC2B
단방향 통신 채널 channel.
② DDC 2AB/DDC2B+/DDC2Bi
양방향 통신 채널 .
주
• PC 가 DDC 기능을 지원해야 합니다 .
E-DDC( 확장 DDC)
I²
C 에 기반을 둔 프로토콜로써 디스플레이와 호스트간
의 양방향 데이터 채널 상에서 사용됩니다 . 이 프로토
콜은 A0/A1 의 I²
C 주소 및 주소 60 을 통해 장치에
액세스합니다 . 주소 60 은 세그먼트 레지스터로 사용
되어 DDC2B 프로토콜을 사용한 것보다 더 큰 용량의
데이터 검색을 가능하게 합니다 . 이 프로토콜은
DDC2B 와 호환됩니다 .
DDC 葉、モニターがその状態をホスト • システム(P
C)へ自動的に通知する通信チャンネルです。
DDC プロトコル
① DDC1/DDC2B
一方向通信チャンネル。
② DDC 2AB/DDC2B+/DDC2Bi
双方向通信チャンネル。
注
• このためにはPCがDDC機能をサポートしなけ
ればなりません。
E-DDC(Enhanced Display Data
Channel)
I²C べースプロトコルで、ディスプレイとホスト間の
双方向デ-タチャネルに使用するプロトコル。
このプロトコルを使用して、60 というアドレスと同
様に、A0/A1 という I²C アドレスのデバイスにアク
セスします。
60 というアドレスをセグメントレジスタとして使用
すると、DDC2B プロトコルを使用するよりも、大容
量のデータを取り出すことができます。E-DDC は
DDC 2B プロトコルと互換性があります。
5
‫)‪DDC(Display Data Channel‬‬
‫العربية‬
‫‪( DDC‬قناة بيانات الشاشة)‬
‫‪ DDC‬هي قناة تواصل تُعلم الشاشة من خاللها النظام المضيف‬
‫(الكمبيوتر) تلقائياً حول قدراتها‪.‬‬
‫بروتوكول ‪DDC‬‬
‫① ‪DDC2B/DDC1‬‬
‫قناة تواصل أحادية االتجاه‪.‬‬
‫② ‪2AB/DDC2B+/DDC2Bi DDC‬‬
‫قناة تواصل ثنائية االتجاه‪.‬‬
‫مالحظة‬
‫يجب أن يعتمد الكمبيوتر وظائف ‪ DDC‬للقيام بذلك‪.‬‬
‫‪E-DDC‬‏(‪ DDC‬معززة)‬
‫يستند البروتوكول إلى ‪ I2C‬ويُستخدم على قناة بيانات ثنائية االتجاه‬
‫بين الشاشة والجهاز المضيف‪ .‬يصل هذا البروتوكول إلى األجهزة على‬
‫عنوان ‪ I2C‬الخاص بـ ‪ A1/A0‬باإلضافة إلى العنوان ‪ .60‬يُستخدم‬
‫العنوان ‪ 60‬كسجل مقطع للسماح باسترداد كميات كبيرة من البيانات‬
‫تفوق الكميات الممكنة باستخدام بروتوكوالت ‪.DDC2B‬‬
‫البروتوكول متوافق مع بروتوكوالت ‪.DDC2B‬‬
‫‪6‬‬
Download PDF

advertising