advertisement
▼
Scroll to page 2
of 36
P/No.: 3828EA3024L Washing Machine OWNER'S MANUAL MODEL : WFT10C60(1)D(E,F)C(H,P,D,E,F,M) WF-TS1288TH WF-T1330TP Please read this manual carefully before operating your set. Retain it for future reference. Record model name and serial number of the set. Quote this information to your dealer when you require service. P roduct Features Washer doesn't operate while the lid is open. If the lid is open rinse or spin cycles, the operation stops for safety. during the wash, sensors The automatically detects the quantity of a Detergent put by a user and temperature and the quality of water to make the best washing algorithm for washing and rinsing, which can give the best washing effect. sensor FUZZY the logic control A built-in load sensor automatically detects the laundry load and a microprocessor optimizes washing conditions such as ideal WATER LEVEL and washing time. SENSING START SETTING Laundry Sensor Optimum Washing Water Level Sensor WASHING Condition Advanced ensures AUTO POWER OFF technology is built into washing result. the Electronic Control System which the best Turbo drum When "Punch washing (option) washing wings turn, the washing opposite direction. This makes the both sides current of water which improve washperformance by rubbing clothes strongly. + 3" tub turns in the Applied 3 models : WFT Step washing 3 step washing makes the best Rubbing and Shaking Rubbing ATTENTION washing performance with Be sure low tangling. Shaking and Disentangling to remove the unit from the carton base, otherwise the machine will not be able to operate properly. Contents READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. Introduction Before Starting Safety to Wash Information Identification of Parts 5 Function Information 6 Preparation Before Washing 7 Use of Water, 8 Special Washing Programs 4 Detergent, Bleach and Softener Guide for Stain Removal 11 Function of each Button 12 FUZZY Wash 14 (Normal Wash) ECONOMY Wash 14 JEAN Wash 14 WOOL Wash 14 DELICATE 14 SOAK Wash 16 FAVORITE Wash 17 SILENT 18 Additional Function TUB CLEAN 19 Program Option Washing 20 DELAY START (RESERVATION) Wash Other Useful Functions Installation Care and Maintenance Troubleshooting Terms of Warranty Specification Placing and Water Connecting Drain Hose Grounding 23 24 Leveling Connecting Supply 22 Hose Method 25 28 29 Cleaning and Maintenance 30 Common washing problems 32 Troubleshooting 33 Terms of 34 Warranty Specification 35 4 S afety Information WARNING! Read and follow this safety information carefully. safety, the information in this manual must be followed to minimize the shock, or to prevent property damage, personal injury, or loss of life. For your Introducin risk of fire or explosion, electric Save these instructions. ? WATER HEATER Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. SAFETY Hydrogen gas can be explosive under these circumstances. If the HOT water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all HOT water faucets and allowing them to run for several minutes. Do this before using any electrical appliance which is connected to the HOT water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process. PROPER ? The base opening must not be obstructed by carpeting when the washing machine is installed on ? Install or store where it will not be exposed to temperatures below freezing or exposed to the INSTALLATION a carpeted floor. weather. ? Properly ground washer to conform with all governing codes and ordinances. Follow details in ? Must be positioned Installation Instructions. YOUR ? LAUNDRY AREA ? THE WASHER ? ? ? ? ? that the plug is accessible. Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc. Close supervision is necessary if this appliance is used by or near children. Do not allow children to WHEN USING so play on, with, or inside this or any other appliance. Use this appliance only for its intended purpose as described in this Owner's Manual. Never reach into washer while it is moving. Wait until the machine has completely stopped before opening the lid. Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing different chemicals can produce a toxic gas which may cause death. Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, dry-cleaning solvents, kerosene, etc.) which may ignite or explode. Do not add these substances to the wash water. Do not use or place these substances around your washer or dryer during operation. The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer's wash and care instructions. ? To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning. NOTE: Pressing Power button to turn off does NOT disconnect the appliance from the power supply. WHEN NOT IN ? Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. ? Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or USE ? rupture should occur. Check the condition of the fill hoses; they may need replacement after 5 years. Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside. ? Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner's Manual, or in published user-repair instructions that you understand and have the ? skills to carry out. Do not tamper with controls. 5 Identification of Parts Body POWDER DETERGENT AND SOFTNER BOX WATER SUPPLY HOSE Make sure the water does not leak. POWER PLUG If the supply cord is damaged, it must be replaced by the BLEACH DISPENSER manufacturer or its service agents or similarly qualified person in order to avoid a hazard. FUNCTION SELECTOR TUB LINT FILTER Clean Use to start or regularly linting START/PAUSE BUTTON on to stop the clothes load. stop the washing machine temporarily. DRAIN HOSE for pump model Check if the drain hose is hung up before operating the washing machine. DRAIN HOSE for non pump model ADJUSTABLE LEGS Use to level the washing machine for correct balance & spin operation. BASE Accessories Water supply hoses Drain hose or or 1 Each for COLD and HOT water Note Part can be different according to the model. Introducin 6 F unction Information Our machine provides various washing methods which suits various conditions and types of laundry. Different types of laundry washing FUZZY(Normal) Use this Wash Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 14) JEAN Wash Use this Program for heavily soiled durable garments e.g. overalls, jeans. Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 14) DELICATE Wash Use this program to wash DELICATE and washable laundries. (refer to page 14) WOOL Wash Delicate clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 14) The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed. Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them Before washing your woolens check the care label for the washing instructions. When washing woolens use a mild Detergent recommended for washing wool. Hand washed woolens may be spun in a washing machine to reduce the time they take to dry. To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.) Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to handwash these articles and place them in the machine to spin dry. ? ? ? ? FAVORITE Wash This setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 17) SILENT Wash Use this program to wash Washing according quietly at night. (refer to page 18) to the condition of laundry ECONOMY Wash ECONOMY wash can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 14) SOAK Wash SOAK Wash can be selected to wash dirt and grime. (refer to page 16) Other washing heavily soiled laundry by soaking in water for some time to remove method TUB CLEAN Use this program to clean the inside of washing machine especially Inner tub & Outer tub . (refer to page 19) DELAY START Wash DELAY START Wash is used to The number of hours to be delay the finishing time of the operation. delayed can be set by the user accordingly. (refer to page 22) OPTION WASH When the user needs only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN, (refer to page 20) SOAK/WASH/RINSE/SPIN. 7 Before Preparation Washing BeforStaingWsh Care Labels * a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. Look for Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed. Sorting To get the best results, different fabrics need to be washed in different ways. ? SOIL ? COLOR (Whites, Lights, Darks) LINT (Lint producers, Collectors) ? (Heavy, Normal, Light) Lint Producers Terry cloth, Chenille, Towels, Nappies, Diapers Synthetics, Corduroy, Permanent Press, Socks Lint Collectors Check before ? ? ? pockets to make sure that they are empty. Things such as nails, hairclips, matches, and keys can damage both your washer and your clothes. Mend any torn garments or loose buttons. Tears or holes may become larger during washing. Remove belts, underwires, etc. to prevent damage to the machine or your clothes. coins, Pretreat any dirt and stains. sure the clothes are washable in water. ? Make ? Check the ? on stains or heavy soil Pretreat shirt collars and cuffs with Before ? WIRE washing instructions. Remove tissue in pockets. Pretreatment ? Loading Check all pens, ? Separate clothes according to the type and amount of soil. Separate white fabrics from colored fabrics. Separate lint producers and lint collectors. Use a a pre-wash product or liquid Detergent when placing them in the washer. washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent. pretreat soil and stain remover. Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove. (For more detail refer to page11) Loading Do not wash fabrics WARNING containing flammable materials (waxes, cleaning fluids, etc.). Fire Hazard Load Size The WATER LEVEL should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer tub. To add items after washer has started, press Start button and submerge additional items. Close the lid and press Start button again to restart. Light and Large-sized clothing Clothes like downs and woollens Never place items in the washer that are dampened with gasoline or other flammable fluids. No washer can completely remove oil. dry anything that has ever had any type of oil on it (including cooking oils). Doing so can result in death, explosion, or fire. Do not light weight, large and float easily. Use a nylon net and laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping. wash them in a are small amount of water. If the Long laundry items nylon nets for long, DELICATE items. For laundry with long strings or long length a net will prevent tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes. Nylon net is not supplied by LG. Use , 8 U BeforStaingWsh Using of Water, se Detergent, Bleach and Softener Water Amount of WATER LEVEL ? ? This machine detects the quantity of laundry automatically, (to be used) will be shown on ? The ? When the WATER LEVEL is though the The amount of Water a same panel. amount of water. automatically detected, WATER LEVEL is indicated cup in the diagram is it may differ depending the control panel. on the quantity of laundry on about 40g for concentrated Detergent. Temperature ? The machine sets the ? You ? the control following table shows the even ? then sets the WATER LEVEL and proper amount of Detergent. When you select a wash program, the WATER LEVEL and amount of Detergent appropriate temperature automatically according to the wash program change Temperature by pressing the WATER TEMP. button. (refer to page 12) The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results. . the Water can We recommend temperatures of: - - - ? White Most items 49~60°C...(120-140˚F) 29~40°C...(85-105˚F) COLD* 18~24°C...(65-75˚F) items, diapers, underclothing and heavily soiled, colorfast items. Only very bright colors with light soil. washing in COLD water additional steps may be needed: Adjust Detergent amount and pre-dissolve Detergent in WARM water When - - - - * HOT WARM Pretreat spots and stains Soak heavily soiled items appropriate bleach Use Temperature below 18°C...(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc. In addition, Detergent manufactures and care labels define COLD water as 26~29°C...(80-85˚F). If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively. Attention If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be necessary for severe cases. Using Detergent Detergent Follow the Use more Detergent package directions. Using too little Detergent is a common cause of laundry problems. Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature. Choosing the right Detergent We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or washing woolens granulated soap powders should not be used in your washing machine. When remember to use Detergent suitable for washing woolens. 9 Using Detergent How much Detergent When you select a wash program the WATER LEVEL and the amount of Detergent (to be used) will be shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated Detergent. The correct amount of Detergent will vary depending on the amount of soil in your clothes cloches may need more Detergent, while bath towels usually need less.). For liquid and concentrated Detergents, follow the recommendations of the (Jeans and work Detergent manufacturer. Note: To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough Detergent has been used; soil and lint can settle back on the clothes or the washing machine. If excess Detergent is used, the rinse will environmental Adding the pollution, so use it not be as clean and efficient. Also, it could cause accordingly. Detergent Powder Detergent / Fabric Softener dispenser. Open the Detergent dispenser and deposit the appropriate amount of Detergent Where you where you deposit the Detergent deposit the Powder Detergent dispenser. detergent Some Detergents MUST be fully dissolved before adding to your machine to get the best wash results. Check the instructions on the Detergent packet. If you use powdered Detergent it is essential that the required amount be fully dissolved in very HOT water before being added to WARM or HOT water for the actual wash. Pre-dissolving Detergent in WARM water when washing in COLD water can improve its performance. Using Liquid ? ? ? ? Bleach clothing care label for special instructions and separate the laundry to be bleached Dilute liquid chlorine bleach. Measure the recommended amount of liquid bleach carefully following instructions on the bottle. Before starting the washer, pour measured amount of bleach directly into bleach dispenser. Avoid splashing or overfilling. Powdered bleach should be mixed with water before pouring. Check Bleach dispenser Never pour undiluted liquid bleach directly onto clothes This may cause change of color or damage the laundry. or into the wash basket. Do not mix chlorine bleach with ammonia as vinegar and/or rust remover. Mixing can reduce toxic gas which may cause death. Do not pour powdered bleach into bleach or acids such a dispenser. 10 U BeforStaingWsh Using se of Water, Detergent, Bleach and Softener Fabric Softener Available Fabric Softener ? Do not ? For use more concentrated fabric softener. This may cause some problems in automatic products instructions for use. Don't Fabric Softener use softener with detergent. Use Powder softener in last rinse water ? When ? When using dispenser, (30ml) with fresh ? ? dispensing. details refer to the softener Depositing ? Type Fabric Softener (30ml) do not dispenser. Where you deposit the softener dilute softener water filling dispenser, Detergent / splash or overfill. It may stain clothes. Never pour fabric softener directly Limit Line on Depositing clothes. It may stain them If spotting occurs, wet and rub with hand dishwashing liquid (or mild bar soap) If the softener is over filled, it can overflow. and rewash. Fabr ic Softener softener don't fill it above the limit line. Cap NOTE Fabric Softener will be inserted automatically during the final rinse and the machine When water pressure is low, the softener may have to be inserted Scrud(Waxy Build gives on alarm sound. manually. up) Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with Detergent. This build-up is not brought about by a fault in the machine. If scrud is allowed to build-up in the machine it smell in your washer. If you wish to ? ? ? ? ? ? use fabric softener we can result in stains on your clothes or an unpleasant recommend Using fabric softener sparingly. filling the dispenser, do not splash or overfill. Clean dispenser as soon as the cycle is finished. Clean your machine regularly. (refer to page 19 or 30) Cold water washing increases the chance of this build-up occurring. When HOT wash e.g. every 5th wash should be at least a warm one. Fabric softener of thinner consistency is less likely to leave residue build-up. We recommend on the a regular WARM or dispenser and contribute to a 11 Guide for Stain Removal Special WARNING Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death. To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below: ? ? ? ? ? ? Read and comply with all instructions on stain removal products. Keep stain removal products in their original labeled containers and out of children's reach. Thoroughly wash any utensil used. Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result. Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode. Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks. For successful stain removal: ? Remove stains ? Determine the kind of promptly. stain, then follow the recommended treatment in the stain removal chart below. ? To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular Detergent and water. ? Use COLD water ? Check ? Check for colorfastness ? Rinse and wash items after stain removal. care on unknown stains because HOT water label instructions for treatments to avoid by testing stain on remover on an can set stains. specific fabrics. inside Follow fabric care label instructions seam. Stain Removal STAIN Adhesive tape, rubber cement chewing gum, Baby formula, dairy products, egg Beverages (coffee, tea, soda, juice, alcoholic beverages) Blood Candle wax, crayon Chocolate Collar or cuff soil, cosmetics Dye transfer on white fabric Grass Grease, oil, tar (butter, fats, salad dressing, cooking oils, car grease, motor oils) Ink Mildew, scorch Mud Mustard, tomato Nail polish Paint, varnish Rust, brown or yellow discoloration Shoe polish TREATMENT Apply ice. Scrape off excess. Place stain face down on paper towels. nonflammable dry cleaning fluid. Use Saturate with prewash stain remover or product containing enzymes to pretreat or soak stains. Pretreat stain. Wash using COLD water and bleach safe for fabric. Rinse with COLD water. Rub with bar soap. Or pretreat bleach safe for fabric. or soak with product containing enzymes. Wash using Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric. Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. Pretreat with prewash stain remover or rub with bar soap. Use packaged color remover. Wash using bleach safe for fabric. Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash using hottest water safe for fabric. Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured alcohol or nonflammable dry cleaning fluid. Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly mildewed fabrics may be permanently damaged. Brush off dry mud. Pretreat or soak with product containing enzymes. Pretreat with prewash stain remover. Wash using bleach safe for fabric. May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain. Repeat, replacing paper towels frequently. Do not use on acetate fabrics. WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed, OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing. For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration. LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach safe for fabric. BeforStaingWsh 12 F BeforStaingWsh unction of each Button BUTTON (INDICATION OF DETERGENT AMOUNT) (OPTION) Use to select Water ? ? Temperature. Pressing the button allows ? you to select COLD WARM (HOT&COLD) HOT adjust the WATER LEVEL as required. The appropriate amount of Detergent is shown next to the WATER LEVEL in the WATER-DETERGENT diagram WATER LEVEL is automatically selected for FUZZY Use to The following COLD LARGE EX-LARGE SMALL SMALL MEDIUM MEDIUM LARGE This button allows you to select the strength of the water current. Power option sequence as selections GENTLE the button is as pushed. Adjustment washing. can (RESERVATION) When DELAY START (RESERVATION) program is selected, it indicates the finishing time. (RES.=DELAY) - can be made while Alarm indication -When an error occurs, LARGE delayed finishing time. Use to set The time increases when the button is pushed. The following settings the button is pushed 3 ...11 be 48 ? a 12 14 16 Wash. Rinse. ? ? are indicated 4 5 as delay time, switch off. ? (refer to page 22) rinse, spin adjusted. The time increases when the pressed If adjustments the ? button Use when wash, button is ...46 turn the power Spin time need to be 3 HOUR. To cancel an error message appears to indicate the abnormality. For example, indicates that the lid is open. ? NORMAL This ? MEDIUM ? ? selected for any program, but when washing jeans, it starts with Strong. ? DELAY START INDICATION - is indicated. EX-LARGE . light up in follows NORMAL STRONG ? DELAY START (RESERVATION) BUTTON STAIN LEVEL BUTTON ? Time left settings are indicated as the button is pushed LARGE During operation, the remaining time ? (normal) program. respectively. Default setting is COLD. ? LEFT, DELAY START (RESERVATION), ALARM INDICATION TIME WATER LEVEL BUTTON WATER TEMPERATURE . are needed wash, press the during [start/pause] button before making any changes. When the button is pressed during washing, the remaining time is displayed. Note * the washing algorithm, the displaying time may be changed during washing-increased by maximum and decreased by 4 minutes at maximum. If the Detergent quantity is put more than the standard, for increasing the rinsing performance, it automatically For optimizing 8minutes * remaining time may be increased. by the sensor changing the algorithm is set by the normal standard. It may not be same to the washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit. The sensor for a Detergent quantity is designed to detect based on a synthetic Detergent powder. If you put a liquid one or a natural one or too much bleaching agent, the detecting ability of the sensor may be decreased. adds * * at rinsing, and the The standard detected 13 WASHING CONDITION INDICATOR ? ? only operates in FUZZY Program. During being detected by the sensor, the LED flashes green, orange and red in turn. And, after detecting, the LED lights a specific color according to It the detecting condition as follows: If the current washing condition (Detergent quantity, Water Temperature, water quality, etc.) is determined as better than the standard one, it optimizes the algorithm to save the energy by decreasing washing time/strength, and the LED automatically turns to red. If the current washing condition is determined as worse than the standard one, it optimizes the algorithm by increasing washing time/strength, and the LED automatically turns to orange. If the current washing condition is determined as equal to the standard one, the algorithm has no change and the LED turns to green. AUTO OFF (POWER) BUTTON ? ? ? CHILD LOCK FUNCTION ? Use to lock or unlock the control buttons to prevent settings from being changed by a child. To lock, push the RINSE and SPIN buttons simultaneously and to unlock push them one more time during the washing process. (refer to page 23) Use to turn the power on or off. Push again and power goes on or off The power goes off automatically about 10 seconds after the wash is finished. START/ PAUSE BUTTON PROGRAM BUTTON ? ? Use for selecting wash program. This button allows you to select 8 different programs for different kinds of laundry ? and dirtiness. program selections light up in sequence follows: FUZZY (NORMAL) DELICATE WOOL TUB CLEAN etc. ECONOMY SILENT ? ? Use to start or pause the washing process. Repeats start and pause by pushing the button. as JEAN FAVORITE FUZZY (NORMAL) Select the desired program by pressing the button. * * detecting ability of the sensor may be decreased by using it for a long time, periodically use TUB CLEAN course to clean the tub. (refer to page 19) Even if the water level or the water temperature are changed by the user in FUZZY(Normal) Program, the sensor will still work. The sensor algorithm may differ according to models. * The control Because the panel may differ according to different models. BeforStaingWsh 14 Washing Programs WashingProm Add the Washing Programs Add the laundry FUZZY Wash 1 Detergent 2 4 (Normal Wash) Used for normal loads, this mode automatically selects the most appropriate conditions and completes the sequence in one operation. The built-in sensor detects the size of the load and the ideal wash power and wash, rinse and spin times are set accordingly. Add the appropriate quantity of Detergent as indicated by the WATER LEVEL next to WATER DETERGENT. Or follow the Detergent manufacturer's instructions 1 3 ECONOMY Wash Use this mode when lightly soiled clothes for time. The laundry highly Select the ECONOMY washing a program the Control short on recommended amount is under 2.0kg. panel. 1 3 5 2 Add the appropriate quantity of Detergent as indicated by the WATER LEVEL next to WATER DETERGENT. Or follow the Detergent manufacturer's instructions 5 2 JEAN Wash Use Jean program when different sizes Spread the jean evenly in the tub washing Jeans of 1 3 Select the JEAN program on the Control panel. 5 2 WOOL Wash Use this program for washing delicate fabrics such as lingerie and woolens. Select the WOOL program on the Control (wash only "water washable" clothes) Before washing your woolens check the care label for the washing panel. (wash only water washable clothes) DELICATE action. This would include blouses, nylons and dress shirts with light soiled. Detergent appropriate for the laundry. When washing woolens use a mild Detergent recommend- ed for washing wool. instructions. Use this program to wash items requiring a GENTLE WASH Use neutral 1 3 2 Select the DELICATE program on the Control panel. 5 15 Close the lid 3 5 Caution & Note Finish 6 If water is already in the tub, wet laundry or into the tub before putting starting will increase the WATER LEVEL. The pulsator rotates for 8 seconds to detect the laundry load. Then the WATER LEVEL and the amount of Detergent to be used will be shown and water will be supplied. Water will be supplied for 2 minutes after the start of the wash to supplement the water the laundry has absorbed. When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically. 4 6 7 4 6 7 4 6 7 With lightweight bulky loads, LEVEL can WATER be set low. Changes to Water Temperature (HOT/COLD) and wash level are possible during operation. (refer to page 12) When setting the WATER LEVEL manually, do not set to Medium to prevent damage to laundry. Washing with HOT water may damage the laundry (Water is set to cold automatically). Ensure that the load is under 2kg. In order to avoid damage to laundry, the spin cycle may appear slow. This also avoids wrinkles and clothing may still contain normal. 4 6 7 Before some water. This is starting to wash, make sure that laundry is washable. Washing with HOT water may damage the laundry (Water is set to COLD automatically). the WashingProm 16 S WashingProm OAK Wash Use this mode to wash normal clothes SOAK mode can be used with FUZZY or or thick and heavy clothes which are excessively JEAN or SILENT or FAVORITE program. 1 Press the AUTO OFF 2 Press the PROGRAM button to select the (POWER) button to turn power not DELICATE, work in WOOL and TUB CLEAN ECONOMY, Program. Press the WASH button, to select SOAK program. ? ? 4 on. washing program. SOAK will 3 dirty. Add the Detergent. Keep pressing the WASH button until the light turns on Soak and Wash simultaneously as next image. SOAK program only works when socking time is 40, 50 or 60 minutes. The appropriate quantity of Detergent marked next to the WATER LEVEL of WATER-DETERGENT. 5 Add the laundry and press the START/PAUSE button. The WATER LEVEL and the amount of Detergent to be supplied. used will be shown and water will be 6 supplied for 2 minutes after the start of the supplement the absorbed water by the laundry. Water will be Close the lid. wash to Finish When the wash program ends, the buzzer will ring for 10seconds before the Power goes off automatically. Note ? Order of Soak-Wash timing Soak-Wash Lamp min ? ? min min min min min Select soaking time 40minutes, 50minutes, the Wash button repeatedly. Off or min min 60minutes If necessary, select the times of Rinse and the time for buttons till you reach the desired times. min min min (including washing time) by pressing Spinning by pressing the Rinse or Spin 17 FAVORITE Wash Pressing the FAVORITE button allows you to store your FAVORITE cycle memory and then recall it for use at a later time. wash conditions in the normal 1 Press the AUTO OFF 2 Select the FAVORITE program. 3 Select your FAVORITE wash conditions. (POWER) button to turn power ? WashingProm on. Press the WATER TEMP. button to select wash Water Temperature. ? Press the WATER LEVEL button to select WATER LEVEL. ? Press the STAIN LEVEL to select STRONG wash ? or GENTLE option. Press the WASH button, the RINSE button & the SPIN time, rinse time & spin time button to select wash respectively you 4 want to store. Press the START/PAUSE button to store & start your FAVORITE wash Power turns off automatically after wash. Note To recall your FAVORITE 1. Press POWER on. 2. Select the FAVORITE cycle. cycle by pressing the PROGRAM. 3. Press the START/PAUSE button. Then the wash cycle starts. cycle. 18 S WashingProm ILENT Wash Use this program to wash quietly in SILENT especially during late button to turn power on. 1 Press the AUTO OFF 2 Press the PROGRAM button to select SILENT program. 3 Add the 4 Press the START/PAUSE button. 5 Add the laundry (POWER) into the Detergent washing night and dawn. tub. and close the lid. Note ? ? SILENT program takes To reduce noise in more longer washing spinning, spin rpm moisture than normal. time than FUZZY (Normal) is lower than normal program. spinning rpm. So the laundry has 19 TUB CLEAN If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer. Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this program to clean inner tub and outer tub. 1 Press the POWER button to turn power 2 Press the PROGRAM button to select the TUB CLEAN program. on. Ex-Large WATER LEVEL is 3 5 automatically. Press the START/PAUSE button. ? 4 set Left time is displayed. After 10 minutes of water ? Do not ? Do not supplement. Add the oxygenated bleach ? When ? using ? using this program When the lid is open the machine will not operate, and alarm signal will remind you to close the lid. lint inside lint filter. place any This program takes about 3 hours to be this program, After using ? After finishing ? remove this program, do not ? ? remove laundry ? dirt inside filter. this program, open the lid of wash to Do not pour bleach into the tub Do not leave diluted Use this program Do not use inside tub. completed. directly. oxygenated bleach It might once for every month. this program repeatedly. remove cause inside tub for It rusts the tub must drain the remained diluted ? m ). Detergent box. place any laundry inside tub. Note Before 300 use Close the lid. ? (about irritant odor. damage the tub. long time. oxygenated water out. an AditonalFucPrgm 20 0 AditonalFucPrgm 1 ption Washing When you only need the Wash, Wash/Rinse Press the AUTO OFF 2 (Power) or Rinse button to turn power Only Wash timing. these can be set manually. on. Only Wash,Rinse Press the WASH button to select the desired cycles, (refer to page 12) Press the WASH button to select the desired timing. (refer to page 12) Press the RINSE button to select the desired times of rinse. (refer to page 12) can use this option for wrinkles of laundry You 3 preventing Press the WATER LEVEL button, to control the water level according to the laundry. If you do not choose anything, it is set the middle water level automatically. (refer to page 12) amount of 4 Add the 5 Press the START/PAUSE button. 6 Add the laundry into the detergent washing tub. and close the lid. 21 1 Press the AUTO OFF 2 Only (Power) button to turn power on. Only Spin/Only drain Only Rinse,Spin Rinse Press the RINSE button to Press the RINSE button to Press the SPIN button to select the desired times of select the desired times of select the desired times of rinse. rinse. (refer to page 12) spin. (refer to page 12) (refer to page 12) Press the SPIN button to select the desired times of spin. 3 (refer to page 12) Press the WATER LEVEL button to control the water level according to the amount of laundry. (refer to page 12) 4 Add the 5 Press the START/PAUSE button. 6 Add the laundry into the detergent washing When you want to only drain, wait until the water in the washing tub drains completely. tub. and close the lid. Note When a Wash, Wash/Rinse or Rinse only option is selected, after the wash is completed the water will not be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained completely. Then press the START/PAUSE button. If you do not specify the water level, then Medium will be automatically selected. selected, the process will start from Water Supply. If only Rinse is AditonalFucPrgm 22 D AditonalFucPrgm ELAY START (RESERVATION) Wash DELAY START (RESERVATION) Wash is used to delay the finishing time of the The hours to be delayed can be set by the user accordingly. The time on the display is the finishing time not the start time. operation. , 1 Press the POWER button to turn power 2 Press the PROGRAM button to select the on. washing program. Select the program for laundry on the Control panel. This program will not work in WOOL and DELICATE Program. 3 Press the DELAY START button. (RESERVATION) ? The light will ' DELAY' turn ? 4 Add the Detergent. on and will be marked. 'TIME LEFT' to set the desired finishing time. washing in 9 hours from now, by make the number 9:00 pressing the DELAY START (RESERVATION ) button repeatedly. Press the button repeatedly To finish For example, The appropriate quantity of Detergent marked next to the WATER LEVEL of WATER?DETERGENT. When the lid is open the machine will not operate, and alarm signal will remind you to close the lid 5 Add the laundry and press the START/PAUSE button. When you press the START/PAUSE button the blink. 6 an supplied for 2 minutes after the start of the supplement the water the laundry has absorbed. Close the lid. Water will be Finish The wash to light will washing will be finished according to the delayed time. Note ? Finishing time can be delayed from 3~48hours. Delaying from3~12hours can be done in 1 hour time intervals and from 12~48hours in 2 hour time intervals. ? ? If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid. To select washing time, rinsing times, spinning time, water level, hot/cold or wash power manually, press the (RESERVATION) button and select the desired option. Then press the START/PAUSE button. laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning (The laundry will be wrinkled if left for a long time after spinning.) DELAY START ? When the program . 23 O ther Useful Functions Child Lock Function If you want to lock all the child lock keys to prevent settings from being changed by a child, you can use the option. How to Lock 1 Press the POWER button. Turn Power 2 Press the START/PAUSE button to start washing. After all 3 on. washing conditions Press both the RINSE button and the SPIN button are set according to the manual. simultaneously. During the wash program, all the buttons are locked washing is completed or it is child- lock function is deactivated manually. until How to Unlock If you want to unlock during wash, press both the RINSE and the SPIN button simultaneously again. Note " " Mute & the remaining time are alternatively shown on the display while they are locked. Option If you want to use the washing machine without alarm buttons simultaneously. To make buzzer one more time. Time the remaining time for each process, press one of the WASH, remaining time for each process will appear for about 1 second. see The press both the WASH and SPIN work, press both the WASH and SPIN buttons simultaneously Seeing Remaining To signal sounds, RINSE and SPIN buttons. AditonalFucPrgm 24 Placing Please and ensure Leveling that transit restraint has been removed before your machine. operating Instal ion 1 Place the machine on a flat and firm surface which allows proper clearance. We suggest a minimum clearance of 2 cm to the right side and left sides of the machine for ease of more than 10 cm installation. At the rear, a minimum clearance of 10 cm more is than suggested. 2cm more than 2cm Caution If the washer is installed spin failure It must be 2 on a uneven,weak or tilted floor causing excessive vibration, " error can placed on a happen to it. firm and level floor to prevent spin failure. Check that the machine is level Open the lid same as 3 " or and look from above to see if it is Top view of the machine shown. Leveling the machine Lift the front of the washing machine the until the surface bubble is and twist Adjustable Leg placed in the center. Adjustable legs Level indicator Caution If the power is supplied from a cord extension set or generator, the cord extension set or electrical portable outlet device should be positioned so that it is not exposed to splashing ingress of moisture. or 25 C onnecting Water Normal Supply Type Hose Fixing tap (Normal tap without thread & the Untighten Hose to water screw type inlet hose.) Rubber screw Untighten the screw of the connector so tap can be placed in the middle. 2 Supply Before connecting the Water Supply Hose to the water tap, check the hose type and then choose the correct instruction here under. Note that the Water Supply Hose supplied may vary from country to country, Make sure to connect the blue inlet hose to the COLD water tap, and the orange inlet hose to the HOT water tap. Connecting 1 Water packing that the screw Connector the connector to the tap Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 3 screws. Attach the water supply hose securely to the connector Push the water supply hose vertically upwards that the rubber seal within the hose completely to the can Connector so adhere Water tap. Supply 4 Fixing the connector to the water supply Hose hose Attach the water then 5 supply hose to the connector and tighten it by screwing it to the right. Check the connection of water supply hose and the connector After connecting the hose, open the tap to check for any water leakage. If the water leaks, close the tap and start again from step 1 Attention The washing machine is not be reused. to be connected to the water mains using new hose-sets and old hose-sets should Instal ion 26 onnecting C Instal ion Normal 1 Type Separate Water Supply Hose (Normal tap without thread & one touch type inlet hose.) Middle connector from Water Supply Separate Middle connector from the Water Supply Hose by pulling the Pressing Rod and the Pressing Handle that is attached to the Water Supply Hose. Hose Middle Fixed Sticker connector Pressing Handle Pressing Rod Water 2 Supply Hose Loosen the fixed nuts to connect the connector to the tap Untighten the screw of the connector so tap can be placed in the middle. that the Rubber packing screw Fixed sticker Note In case tap is too Guide large. plate If the tap diameter is too large or is square, untighten the 4 screws and remove the guide plate. 3 Then follow Rubber packing step1. Fixing Connectors to the Tap Connector Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. 4 Fixing Upper Connector and Middle Connector Remove the fixed sticker in between the Connector Upper and Middle Connectors. Tighten the connectors by holding one connector and twist middle connector to the right. 5 Connecting Middle Connector Fixed sticker Middle Connector and Water Supply pressing rod of the Water Supply separated from middle connector Step1) and then join it to the middle Connector Middle Connector Hose Press down the Hose which (refer to was Pressing rod connector. Water 6 Check for water After leakage the hose, open the tap to check connecting for any water leakage. If the connection leaks, close the tap and start again from step 1. skip step 1, water leakage may occur. If you Supply Hose Pressing handle 27 Screw 1 Instal ion Type Attach the water Push the water supply supply hose up packing within the hose can so hose to the tap. that the rubber adhere completely to the tap. Water tap Rubber Water 2 Connect the water supply Packing Supply hose to the tap. Connect the water tighten it by 3 supply hose to the tap and then screwing it to the right. Check water leakage. After the hose, connecting leakage. open the tap to check for any water Connecting ? Water Connect the water the Check to Hose to the machine supply hose to washing machine, the hose ? Supply inlet valve of and then lock it by turning connecting part. see if there is a rubber seal inside the Hose connector connector. Rubber seal Hose 28 Connecting Drain Hose Before connecting Drain Hose, check your Drain Hose model and choose the correct instructions. Instal ion Pump Model 1 Fit the end of the drain hose to the outlet of the 2 Put the other end of the drain hose over the drain pump and tighten the clamp. standpipe or wash tub. Hose Guide Within 50 mm 0.9~1.2m Drain Hose Note To prevent siphoning, the drain hose should not extend more than 50 mm from the end of the hose The discharge height should be approximately 0.9 1.2 m from the floor. ~ Non-Pump 1 Before Model connecting Ensure that the hose clip is set as indicated here. Clip 2 Connect the Elbow Hose Push the elbow hose toward the body of the washing machine. 3 Place the Drain Hose change the direction of the hose, pull out the change the direction. 2. Repeat Step To elbow hose and guide. 29 G rounding Method Earth wire should be connected. If the earth wire is not connected, there is caused by the current leakage possible a danger of electric shock . Grounding Method with Ground insert space Terminal If the AC current outlet has a ground terminal, then required. Note that AC power outlet configurations may differ from country separate grounding is to not Ground country Terminal Outlet with Other Grounding Method Burying Copper bury it terminal. Plate Connect the Ground Wire Plate and ground more to a Ground Copper ground. than 75cm in the Ground Wire 75cm Ground Using Ground Wire Copper ground Wire to the socket provided exclusively for Grounding. Plate Connect the Using a Short Circuit Breaker If grounding methods described above possible, employed a Ground Wire are not separate circuit breaker should be and installed by a qualified electrician Short-circuit breaker Caution ? ? To prevent a possible explosion, do not connect ground to a gas pipe Do not connect ground to telephone wires or lightning rods. This may be storms ? Connecting ground to plastic has no effect ? Ground wires should be connected when an extension cord is used. dangerous during electrical CarendMitc 30 Cleaning CarendMitc Cold water ? and Maintenance washing always use COLD water, we recommend that a WARM intervals e.g. every 5th wash should be at least a WARM one. If you or HOT wash be used a regular as sand), at When you have finished ? ? Turn off taps to prevent the chance of flooding should Always unplug the power cord after use. a hose burst. When water supply into the tub is not clean or the filter is clogged with particles filter in the inlet valve occasionally. (The figure of power cord and water tap may vary according to the country) (such clean the To Clean the Filter in the Inlet Valve Close the tap before turning off the power. Select both HOT/COLD and then press the 1 2 Turn off the power before pulling out the cord. 4 Replace the filter after cleaning it. [START/PAUSE] button to remove water completely. from the machine After 3 hose removing the water supply pull out the filter. Then use a brush to clean the filter. Caution Before cleaning the filter, the impurities in the water supply hose should be removed. To Clean the Lint Filter 1 2 Pull out the lint filter from Turn the net inside out the tub in the direction to clean the filter and shown below. rinse it with water. 3 Replace- the filter to the original location. Push the lip of the filter until a pop sound is heard. Note ? If the lint filter is torn To Clean the 1 or damaged, purchase a new one from LG service center. Pump casing (for pump model) Place a towel on the floor under the drain pump cap. Excess water may flow out. 2 Turn the cap counter- clockwise and pull it out. Cap 3 Remove any foreign objects and fluff inside pump filter. Filter casing and from the 4 Replace the cap. Insert the filter along the guide ribs inside the pump casing. Filter must face the guide ribs inside pump casing and securely turn the cap clockwise. Guide rib Filter Caution ? Check if water leaks after reassembling. (The Rubber ring is in the cap) 31 C and Maintenance leaning When there is a fear of ? ? ? freezing Close the water taps and remove the Water Supply Hose. Remove the water which remains in the water supply. Lower the drain hose and drain the water in the bowl and the drain hose by spinning. If frozen ? ? ? supply hose, and immerse it in HOT water at approx.. 40˚C. Pour approx.. 2 liters of HOT water at approx.. 40˚C, into the bowl and let it stand for 10 minutes. Connect the water supply hose to the water tap and confirm that the washing machine performs the Remove the water and supply Wash Inner-tub drainage of water. Leave the lid open after washing to allow moisture to evaporate. If you want to clean the inner-tub use a clean soft cloth dampened with liquid Detergent, then rinse. (Do not use harsh or Inlet Hoses Hoses connecting washer to faucet should be replaced every 5 years. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit sharp objects. Exterior Long Vacations Be Cleaning the ? supply freezing. Inside of your Washer If you use fabric softener inside of your washer. ? do or regular COLD Add about two cups of Stop the washer, After a important that you occasionally clean the powdered Detergent that contains phosphate. Or use soaking, open the lid and leave it to soak drain the washer and TUB CLEAN PROGRAM run it Products that Hydrocarbon (Be washer or ? Use of thinners and the lacquer thinners, solvents as paintwork and components etc. they can are dissolve plastic of your washer. and blister paint flammable DO NOT put them in or liquids can damage your washer's control panel. dyes in your washer may cause staining of the plastic components. The dye will not damage the machine suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in your washer. Do not machine dryer.) Some pretreatment sprays we cycle. during this procedure. petrol, paint washing garments stained with these ? but normal diaper sanitizer will cause damage to solvents i.e. careful when a periodically. might damage your washing Concentrated bleaches and overnight. through We do not recommend that you wash clothes ? it is very washing, Let it operate for several minutes. ? ? water Fill your washer with HOT water. ? ? surface with is shut off at faucets. Drain all water from hoses if weather will water sure be below ? gritty cleaners.) use your washer lid as a work surface. CarendMitc 32 Common washing problems Many washing problems involve poor soil & stain removal, residues of lint and scum, and fabric damage. For satisfactory washing results, follow these Troubleshting instructions. WASH PROBLEM Problems Poor soil removal Solutions & Preventive Measures Possible Causes ? ? Not enough Detergent Wash Water Temperature too low. ? ? Overloading ? Incorrect wash Use WARM or HOT water for normal soil. Temperature may be required according to (refer to page 8) ? pretreat stain Reduce load size. ? Wash with JEAN Incorrect ? Do not amount of Different Water cycle sorting ? size, soil and water Hardness. the washer ? Use correct amount of Detergent for load soil type. or SOAK & JEAN wash cycle for heavy laundry. Separate heavily soiled items from lightly soiled ones. Pretreat stain and heavy soil according to directions shown soiled ? ? on Blue Stains ? Undiluted fabric softener dispensed directly onto ? ? fabric page 7. Rub the stain with bar soap. Wash. Do not overfill fabric softener liquid fabric softener See page 10 for Black or gray marks on clothes Yellow or brown rust stains ? A caused buildup by the ? interaction of fabric softener and Detergent can flake off ? and mark clothes ? Not ? Iron water or manganese in supply, water ? Keep the recommendations against Scrud(waxy buildup). (refer to scrud page10.) Use correct amount of Detergent for load size, amount of soil To restore discolored load of whites, use rust remover safe for fabric. pipes, water heater instructions. more and water Hardness. enough Detergent or dispenser and do not pour directly onto fabric. ? Install nonprecipitating water softener or an iron filter in supply system for an ongoing problem. Before washing, run water for a few minutes to clear lines. your water ? Lint ? ? ? Incorrect sorting pocket Overloading the washer ? or Detergent ? Overloading ? Undissolved ? Use too the washer Detergent much Detergent or Incorrect use of chlorine ? ? Unfastened zippers, hooks, buckles Ribs, tears and broken ? Overloading the washer Degradation of fabric Do not overload the washer Do not overload the washer. Some Detergents need to be pre-dissolved, check the Detergent instructions. ? Try pre-dissolving the Detergent. Increase Water Temperature using HOT water safe for fabric. Use proper amount of Detergent. Never pour chlorine bleach See page 9 for ? Fasten ? Remove threads ? synthetic fabrics and remove tissues sorting and caring ? bleach. snags towels, flannelette sheets, separately ? ? ? eg pockets before loading. ? Holes, tears, givers before wash. See page 7 for ? Residue Wash lint from lint collectors eg Tissues left in directly on fabric. adding liquid bleach. zippers, hooks, objects in and buckles. pockets. loading. ? Do not overload the washer. See page 7 for caring before in 33 T roubleshooting Before calling for service, Symptom Water Supply Failure Error check the Message . . . . . Failure the list bellows. Troubleshting Check up . Drainage problem against Is the water tap shut off? Is the water supply cut off ? Is the tap or water supply hose frozen ? Is the water pressure low or is the filter of the inlet valve clogged with impurities? Is the Hot hose connected to cold? Is the Cold hose connected to hot? . Is the drain hose . Is the drain hose bent . Is the internal part of the hose positioned correctly? or placed too high? or drain pump (only pump model) clogged with impurities? . Spin Failure Door(Lid) Open . Is the laundry evenly balanced? . Is the washing machine placed on a flat surface? . Is the lid closed? . Internal sensing failure Power failure Overflow failure Check if electric power has gone off. Please call your nearest LG Electronics service center for help. 34 Terms of Warranty What Is Not Covered: ? ? ? ? trips to your home to teach you how to use the product. If the product is connected to any voltage other than that shown on the rating plate. If the fault is caused by accident, neglect, misuse or Act of God. If the fault is caused by factors other than normal domestic use or use in Service accordance with the owner's manual. change the set-up of the product. If the fault is caused by pests for example, rats or cockroaches etc.. Noise or vibration that is considered normal for example water drain sound, spin sound, or warming beeps. Correcting the installation for example, levelling the product, adjustment of drain. Normal maintenance which recommended by the owner's manual. Removal of foreign objects / substances from the machine, including the pump and inlet hose filter for example, grit, nails, bra wires, buttons etc. Replace fuses in or correct house wiring or correct house plumbing. Correction of unauthorized repairs. Incidental or consequential damage to personal property caused by possible defects with this appliance. If this product is used for commercial purpose, it is not warranted. (Example : Public places such as public bathroom, lodging house, training center, dormitory) ? Provide instruction on use of product or ? ? ? ? ? ? ? ? ? If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product, or the replacement of a defective part, shall be borne by the owner. 35 S pecification Specifaton H D W WFT10C60(1)D(E,F)C(H,P,D,E,F,M) Model WF-TS1288TH / WF-T1330TP Size 632(W) x 634(D) x 980(H) WFT10C60(1)D(F) 632(W) x 634(D) x 1005(H) WFT10C60(1)E ~ ~ WF-TS1288TH / WF-T1330TP Water tab pressure In our to the 30 - 800 kPa (0.3 - 8.0 kgf/cm2) continuing effort to improve the quality of our appliances, appliance without revising this manual. it may be necessary to make changes
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project