LG | 14CC4RB | LG 14CC4RB Owner’s Manual

Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number
Serial number
:
:
P/NO : MFL42377923-EN (MC059D,MBM39475703)
Contents
Installation.........................................................2
Connection of external equipment..................2
Location and function of controls...................3
Basic operation.................................................4
Other functions.................................................4
On screen menus..............................................5
Setting up TV stations......................................5
Picture adjustment............................................6
Time setting.......................................................6
Troubleshooting check list..............................7
Installation
Power
Service
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover.
Never apply DC power to the set. In the event of
thunderstorms or powercuts, please pull out the
aerial and mains plugs.
Never remove the back cover of the set as this
can expose you to very high voltage and other
hazards. If the set does not operate properly,
unplug it and call your dealer.
Press the POWER button on the front panel or side
panel to turn off the TV when the TV set is not being
used for a long time.It is recommended to remove the
plug from the wall outlet(Power point).
Aerial
Connect the aerial cable to the socket on the back
cover. For the best reception an outdoor aerial
should be used.
Disconnecting device from mains
Mains plug is the disconnecting device. The plug
must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the
set to rain or moisture.
Do not place anything containing liquid on top of
the set, this may cause a fire or could give an
electric shock.
Location
Position your set so that no bright light or sunlight
falls directly onto the screen. Care should be
taken not to expose the set to any unnecessary
vibration, moisture, dust or heat. Also ensure that
the set is placed in a position to allow a free flow
of air. Do not cover the ventilation openings on the
back cover.
Connection of external equipment
Aerial socket
1. Connect the RF out socket of the VCR to the
aerial socket on the back of the set.
2. Connect the aerial cable to the RF aerial in
socket of the VCR.
3. Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.
4. Select the programme number where the
VCR channel is stored.
5. Press the PLAY button on the VCR.
set.
2. If the VCR is connected to the AV sockets on
the set, press the TV/AV button to select AV
(or AV1).
3. Press the PLAY button on the VCR.
The VCR playback picture appears on the
screen.
ANTENNA
IN
IN
Audio/Video in/out sockets (option)
1. Connect the audio/video out sockets of the
VCR to audio/video in sockets of the set and
in sockets of the VCR to out sockets of the
2
VIDEO
VCR
AUDIO
Location and function of controls
Remote control handset
1
selects a favorite programme.
12. I/II/ (option)
selects the language during dual language
broadcast.
selects the sound output.
*
8
Battery installation
2
3
9
The remote control handset is powered by AAA
type batteries. To load the batteries, turn the
remote control handset over and open the battery
compartment. Install batteries as indicated by the
polarity symbols ( + and - ) marked inside the
compartment.
4
or
5
6
7
10
12
11
1. POWER
switches the set on from standby or off to
standby.
2. NUMBER BUTTONS (option)
switches the set on from standby or directly
select a number.
3. MENU
selects a menu.
4. D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
scans programmes automatically.
F / G (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
OK
accepts your selection or displays the current
mode.
5. Q.VIEW
returns to the previously viewed programme.
6. EYE/ (option)
switches the eye function on or off.
7. SLEEP (option)
sets the sleep timer.
8. MUTE
switches the sound on or off.
9. TV/AV
selects TV or AV mode.
switches the set on from standby.
10. LIST
displays the programme table.
11. FAVOURITE (option)
*
Front panel
-
MAIN POWER (ON/OFF)
switches the set on or off.
-
REMOTE CONTROL SENSOR
Note : Only use the supplied remote control
handset. (When you use others, they’ll be
not able to function.)
-
POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby
mode.
dims when the set is switched on.
-
MENU
selects a menu.
-
OK (option)
accepts your selection or displays the current
mode.
F / G (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
3
Basic operation
On and off
1. Press the main power button to switch the set on.
2. If the set is in standby mode, press the
POWER, D / E, TV/AV or NUMBER buttons on
the remote control handset to switch it on fully.
3. Press the POWER button on the remote control handset.
The set reverts to standby mode.
4. Press the main power button again to switch
the set off.
Note : If, while the set is switched on, the mains
plug is disconnected the set will switch to standby
or power on when the mains plug is replaced in
the mains power socket.
Mute function
Press the MUTE button. The sound is switched off
and the display
appears.
You can cancel it by pressing the MUTE, F / G,
I/II/ (option) button.
*
On screen language selection (option)
The menu can be displayed on the screen in
desired language. First select your language.
1. Press the MENU button and then D / E button to select the Special menu
.
2. Press the G button to select Language.
3. Press the G button and then D / E button to
select your desired language.
All the on screen displays will appear in the
selected language.
Press the OK or F button to select the Special
menu.
4. Repeatedly press the MENU button to return
to normal TV viewing.
Other functions
TV and AV modes
Blue back (option)
Inputs can be set for TV or AV mode. AV mode is
used when a video cassette recorder (VCR), or
other equipment is connected to the set.
Note : When a VCR is connected via the aerial
socket the set is used in TV mode. See the
‘Connection of external equipment’ section.
Alternatively you can select the TV or AV mode by
pressing the TV/AV button.
If you select On on the Blue back pull-down
menu, the blue background appears on the
screen when there is no or poor signal.
Note : In the AV mode, Component mode, the
blue background doesn’t appear on the screen.
In AV mode, to return to TV mode, press the D / E
or NUMBER buttons.
Auto AV switching (option)
If your VCR outputs switching voltage when it is
switched to playback with the VCR connected to the
Euro scart socket. The set is automatically switched
to AV or AV1 mode when an AV signal is input. But
if you want to keep on watching TV mode, press the
D / E or NUMBER buttons. Press the TV/AV button to return to AV modes.
Child lock
The TV can be set so that the remote control
handset is needed to control it. This feature can
be used to prevent unauthorized viewing.
With the lock on, the display Child lock on
appears on the screen if any button on the panel
is pressed while viewing the TV.
Note : The display Child lock on will not appear
on the screen if any button on the panel is
pressed while displaying the menus.
4
Sleep timer
You don’t have to remember to switch the set off
before you go to sleep. The sleep timer automatically switches the set to standby after the preset
time elapses.
Press the SLEEP button to select the number of
minutes. The display r- - - will appear on the
screen, followed by 10, 20, 30, 60, 90, 120, 180
and 240. The timer begins to count down from the
number of minutes selected.
Note :
a. To view the remaining sleep time, press the
SLEEP button once.
b. To cancel the sleep time, repeatedly press the
SLEEP button until the display r - - appears.
c. When you switch the set off, the set releases
the preset sleep time.
On screen menus
The dialogue between you and your set takes place
on screen with an operator menu. The buttons
required for the operating steps are also displayed.
Menu selection
1. Press the MENU button and then D / E button to
display each menu.
2. Press the G button and then D / E button to
select a menu item.
3. Press the G button to display the sub menu or
the pull-down menu.
4. Change the setting of an item in the sub or
pull-down menu with F / G or D / E.
You can move to the higher level menu with
OK or F button and to move to the lower level
menu press the G button.
Note : In some models, Language, Blue back,
Game, Booster will not display in the Special menu.
Setting up TV stations
Auto programme tuning
All stations that can be received are stored by this
method. It is recommended that you use auto programme during installation of this set.
System
Storage
Normal
Turbo
{
{
{
{
BG
I
DK
M
(O} {OOKOMENU
)
i
BG : (Asia/New Zealand/M.East/Africa/
Australia)
I
: (Hong Kong/South Africa)
DK : (East Europe/China/Africa/CIS)
M : (USA/Korea/Philippines) (option)
Option: In some models, you can only select Start.
Note : a.Turbo is faster than Normal and in
some models, these searches will automatically s
tore all receivable stations.
b.If the programmed station has poor quality
sound, select the system again in the Manual menu.
Auto programme scan
To automatically scan the pictures of stored programmes, press the D or E button for about 3
seconds. The picture of stored programmes
appears on the screen one by one.
To stop auto programme scanning, press any button except VCR buttons.
Manual programme tuning
Manual programme lets you manually tune and
arrange the stations in whatever order you desire.
Also you can assign a station name with five characters to each programme number.
The selected programme is deleted, all the following programmes are shifted up one position.
Copying a programme
1. Select a programme to be copied with the D / E
or F / G button.
2. Press the GREEN button.
All the following programmes are shifted down
one position.
Moving a programme
1. Select a programme to be moved with the D / E
or F / G button.
2. Press the YELLOW button.
3. Move the programme to the desired programme
number with the D / E or F / G button.
4. Press the YELLOW button again to release
this function.
Skipping a programme number
1. Select a programme number to be skipped
with the D / E or F / G button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the
skipped programme. When a programme
number is skipped it means that you will be
unable to select it using the D / E button during normal TV viewing. If you want to select
the skipped programme, directly enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
Repeatedly press the MENU button to return to
normal TV viewing.
Favourite programme
This function lets you select your favourite programmes directly.
AutoOprog.{
Manual
{
Prog.Oedit {
Favourite {
Booster (option)
If the reception is poor at the fringe area of TV
signal, select Booster to On. When the picture
condition is good, do not select Booster to On.
Programme edit
OOOOCO1DOOOO5OOSO69
O1OOCO03OOOO6OOSO17
O2OOCO12OOOO7OOSO22
O3OOSO66OOOO8OOCO09
O4OOSO67OOOO9OOCO11
DeleteOOOCopy
MoveOOOOOSkip
(O} {OOKOMENU
)
i
Deleting a programme
1. Select a programme to be deleted with the D / E
or F / G button.
2. Press the RED button twice.
560 C0 0 5
( O} {O0_9OOKOMENU
)
i
Calling the programme table
You can check the programmes stored in the
memory by displaying the programme table.
Note :
a.You may find some blue programmes.
They have been set up to be skipped by auto pro
gramming or in the programme edit mode.
b.Some programmes with the channel number
shown in the programme table indicate there is
no station name assigned.
5
Picture adjustment
Note: Picture menu options are not available for
RGB input source.
PSM (Picture Status Memory)
1. Press the MENU button and then D / E button to select the Picture menu
.
2. Press the G button to select PSM.
3. Press the G button and then D / E button to
select a picture setting on the PSM pull-down
menu.
PSM
{
PSM
CSM
{
Contrast {
Brightness{
Colour
{
Sharpness {
Dynamic
Standard
Mild
Game
User
CSM (Colour Status Memory)
You can select the picture colour status; standard,
reddish, greenish or bluish, as you prefer.
1. Press the MENU button and then D / E button to select the Picture menu.
2. Press the G button and then D / E button to
select CSM.
3. Press the G button and then D / E button to
select Standard, Reddish, Greenish or
Bluish on the CSM pull-down menu.
4. Repeatedly press the MENU button to return
to normal TV viewing.
Picture adjustment
(O} {OOKOMENU
)
i
4. Press the OK or F button.
5. Repeatedly press the MENU button to return
to normal TV viewing.
You can also recall a desired picture (Dynamic,
Standard, Mild, Game or User) with PSM button on the remote control. The picture Dynamic,
Standard, Mild and Game are programmed for
good picture reproduction at the factory and cannot be changed.
You can adjust picture contrast, brightness,
colour intensity, sharpness and tint (NTSC input
only) to the levels you prefer.
1. Press the MENU button and then D / E button to select the Picture menu.
2. Press the G button and then D / E button to
select Contrast, Brightness, Colour or
Sharpness.
3. Press the G button and then F / G button to
make appropriate adjustments on the each
sub menu.
4. Press the OK button to store it for the picture
user.
5. Repeatedly press the MENU button to return
to normal TV viewing.
Time Setting
Setting the clock
1. Press the MENU button and then D / E button to select the Time menu
.
2. Press the G button to select Clock.
3. Press the G button and then D / E button to
adjust the hour.
4. Press the G button and then D / E button to
adjust the minute.
5. Press the OK button.
6. Repeatedly press the MENU button to return to
normal TV viewing.
Setting the On/Off timer
By using this function, the set automatically
switches on or off at a preset time. You must set
the time correctly before using on/off time function.
1. Press the MENU button and then D / E button to select the Time menu.
2. Press the G button and then D / E button to
select Off time/On time.
3. Press the G button and then D / E button to
adjust the hour.
4. Press the G button and then D / E button to
adjust the minute.
5. Only On time function; Press the G button
and then D / E button to adjust programme
number and volume level.
6
6. Press the OK button.
7. Repeatedly press the MENU button to return to
normal TV viewing.
Note :
a. On time works only in standby mode.
b. To view the remaining on/off time, select the
Time menu.
c. When you switch the main power off, the
Clock is reset .
d. Two hours after the set is switched on by the
on time function it will automatically switch
back to standby mode unless a button has
been pressed.
Auto sleep
If you select On on the Auto off pull-down menu,
the set will automatically switch itself to standby
mode approximately ten minutes after a TV station stops broadcasting.
1. Press the MENU button and then D / E button to select the Time menu.
2. Press the G button and then D / E button to
select Auto sleep.
3. Press the G button and then D / E button to
select On or Off on the Auto sleep pull-down
menu.
4. Press the OK or F button.
5. Repeatedly press the MENU button to return to
normal TV viewing.
Troubleshooting check list
Symptoms
No picture, no sound
Sound OK, poor picture
Picture OK, poor sound
Picture blurred
Lines or streaks in picture
Poor reception on some channels
No colour
Poor colour
Remote control does not work
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched on
Try another channel (weak signal)
Check aerial (plugged into TV?)
Check aerial (broken lead?)
Check aerial
Check for local interference
Adjust contrast
Adjust brightness
Adjust colour
Adjust volume
Check the batteries in remote control
Check Audio/Video sockets (VCR only)
7
Download PDF