LG | 42PC3MV | LG 42PC3MV Owner’s Manual

PLASMA MONITOR
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number
Serial number
:
:
P/NO : MFL30435802 (RF052A/D)
Safety Warnings
Safety Instructions
- It is recommended that 42/50PC1MH / 42PC3MVH model only be used at an altitude of less than 6561 feet
(2000m) to get the best quality picture and sound.
WARNING
Do not place the set in direct sunlight or near heat
sources such as heat registers, stove and so on.
- This may cause a fire.
Do not use the set in damp place such as a bathroom
or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Do not use water while cleaning the set.
- This may cause damaged the set or could give an electric
shock.
In case of smoke or strange smell from the set, switch
it off ,unplug it from the wall outlet and contact your
dealer or service centre.
- This may cause a fire or could give an electric shock.
Bend antenna cable between inside and outside
building to prevent rain from flowing in.
- This may cause water damaged inside the set and could give an
electric shock.
Do not attempt to service the set yourself. Contact
your dealer or service centre.
- This may cause damaged the set or could give an electric
shock.
Earth wire should be connected.
- If the earth wire is not connected, there is possible a danger of
electric shock caused by the current leakage.
- If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.
During lightning thunder, unplug the set from the wall
outlet and don’t touch the antenna cable.
- This may cause damaged the set or could give an electric
shock.
DISCONNECTING DEVICE FROM MAINS
Power
supplier
Short-circuit
breaker
- Do not connect ground to telephone wires, lightning rods or gas
pipe.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
Do not insert any object into the exhaust vent.
- This may cause a fire or could give an electric shock.
Do not place heavy objects on the set.
- This may cause serious injury to a child or adult.
2 PLASMA TV
- Mains plug is the disconnecting device. The plug must remain
readily operable.
Safety Warnings
* Safety instructions have two kinds of information, and each meaning of it is as below.
WARNING The violation of this instruction may cause serious injuries and even death.
NOTES
The violation of this instruction may cause light injuries or damage of the
product.
Take care of danger that may happen under specific condition.
NOTES
Never touch the power plug with a wet hand.
- This may cause an electric shock.
Ensure the power cord doesn’t trail across any hot
objects like a heater.
- This may cause a fire or an electric shock.
Disconnect from the mains and remove all connections before moving.
Do not plug when the power cord or plug is damaged
or the connecting part of the power outlet is loose.
Do not place the set in a built-in installation such as a
bookcase or rack.
- This may cause a fire or an electric shock.
- Ventilation required.
Dispose of used batteries carefully to prevent a child
from eating them.
- In case that it eats them, take it to see a doctor immediately.
When moving the set assembled with speakers do not
carry holding the speakers.
- This may cause the set to fall, causing serious injury to a child or
adult, and serious damage to the set.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
When installing the set on a table, be careful not to
place the edge of its stand on the end of the table.
- This may cause damage the set or could give an electric shock.
- This may cause the set to fall, causing serious injury to a child or
adult, and serious damage to the set.
Contact the service centre once a year to clean the
internal part of the set.
- Accumulated dust can cause mechanical failure.
The distance between eyes and the screen should be
about 5 ~ 7 times as long as diagonal length of the
screen.
- If not, eyes will strain.
Unplug the set from the wall outlet when it is left unattended
and unused for long periods of time or occurred a state of
emergency.
Do not place an outside antenna in the vicinity of overhead power lines or other electric light or power circuits.
- Accumulated dust may cause a fire or an electric shock from
deterioration through electric leakage.
- This may cause an electric shock.
There should be enough distance between an outside
antenna and power lines to keep the former from
touching the latter even when the antenna falls.
- This may cause an electric shock.
Do not pull the plug not the cord when disconnecting.
- This may cause a fire.
Owner’s Manual 3
Contents
Contents
Safety Warnings
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . .2~3
Introduction
Location and Function of Controls . . . . . . . . . . .6~8
Installation
External Equipment Viewing Setups . . . . . . . . . . . .9
Displayable Monitor Specification . . . . . . . . . . . . .10
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11~12
Operation
Turning on the Set . . . . . . . . . . . . . . . . . . . . . . . .13
On-Screen Menu Language Selection . . . . . . . . .13
Picture Menu Options
PSM (Picture Status Memory) . . . . . . . . . . . . . . .14
CSM (Colour Status Memory) . . . . . . . . . . . . . . .14
Manual Colour Temperature Control . . . . . . . . . .14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
sRGB (RGB[PC],HDMI[PC] mode only) . . . . . . . .15
ACM (Active Colour Management) . . . . . . . . . . . .15
Manual Picture Control . . . . . . . . . . . . . . . . . . . .15
Sound Menu Options
SSM (Sound Status Memory) . . . . . . . . . . . . . . . .16
AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . . .16
Adjusting Sound Control . . . . . . . . . . . . . . . . . . .16
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Time Menu Options
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . .17
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . .17
Auto Sleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
After reading this manual,
keep it in the place where
the user can always
contact easily.
4 PLASMA TV
Special Menu Options
Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ISM (Image Sticking Minimization) Method . . . . . .18
Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Screen Menu Options
Auto adjustment . . . . . . . . . . . . . . . . . . . . . . . . .19
Manual Configure . . . . . . . . . . . . . . . . . . . . . . . .19
Selecting Wide VGA/XGA mode . . . . . . . . . . . . .19
Setting the Picture Format . . . . . . . . . . . . . . . . . .20
Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . . . .20
Screen Position . . . . . . . . . . . . . . . . . . . . . . . . . .21
Cinema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
NR (Noise Reduction) . . . . . . . . . . . . . . . . . . . . .21
Initializing (Reset to original factory value) . . . . . .21
PIP (Picture-in-Picture) Feature
Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Selecting an Input Signal Source for the PIP . . . .22
Adjusting PIP Transparency (PIP mode only) . . . .22
Moving the PIP (PIP mode only) . . . . . . . . . . . . .22
Picture Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Miscellaneous
External Control Device Setup . . . . . . . . . . . .23~28
IR Code (NEC Format) . . . . . . . . . . . . . . . . . .29~30
Troubleshooting Checklist . . . . . . . . . . . . . . . . . .34
Product Specifications . . . . . . . . . . . . . . . . . . . . .35
Introduction
Introduction
What is a Plasma Display ?
If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent substance. At this moment,
light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160° - Wide angle range of vision
A Plasma Display provides more than 160° angle range of vision so that you can get a picture without distortion from any
direction.
Easy installation
A Plasma Display is much lighter and smaller than other same class products so that you can install the Plasma Display
at the desired place.
Big screen
The screen of a Plasma Display is 42" (or 50")so that you can get vivid experience as if you are in a theater.
Multimedia Plasma Display
A Plasma Display can be connected with a computer so that you can use it as a screen for conference, game, internet
and so on.
The explanation about coloured dots may be present on Plasma Monitor screen
The Plasma Monitor which is the display device of this product is composed of 0.9 to 2.2 million cells and a few cell defects
can occur in the manufacture of the Plasma Monitor. Several coloured dots visible on the screen would be acceptable, in
line with other Plasma Monitor manufacturers and would not mean that the Plasma Monitor is faulty. We hope you will
understand that the product which corresponds to this standard is regarded as acceptable. It means that it could not be
changed or refunded.
We promise that we'll do our best to develop our technology to minimize the cell defects.
The explanation about noise of Plasma Monitor
- This feature is not available for all models.
In the same way that a fan is used in a PC to keep the CPU cool, the Plasma Monitor is equipped with cooling fans to
improve the reliability of this product. Therefore, a certain level of noise could occur when the fan is operated. This noise
doesn't have any negative effect on its efficiency and reliability and it's also determined to have no difficulty while using
this product. The noise from the fans is normal in the operation of this product. We hope you will understand that a certain level of noise is acceptable. It means that it is not changeable nor refundable.
TO AVOID BURNING IMAGE INTO THE DISPLAY, DO NOT HAVE A STILL IMAGE ON SCREEN FOR
EXTENDED PERIOD OF TIME. IMAGE AFTER BURN WILL NOT BE COVERED UNDER WARRANTY
ie.Menus, Video games, Borders or LOGOS
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Owner’s Manual 5
Introduction
Location and Function of Controls
- Shown is a simplified representation of the set.
- Here shown may be somewhat different from your set.
<Front Panel Controls>
42PC1M / 50PC1M series
VOL
OK
MENU
INPUT
Power/Standby Indicator
• illuminates red in standby
mode.
• illuminates white when the set
is switched on.
INPUT
INPUT
INPUT Button
POWER Button
6 PLASMA TV
OK
MENU
VOL
OK Button
MENU Button
OK
MENU
D /E
VOLUME Buttons
Buttons
VOL
Introduction
<Front Panel Controls>
42PC3MV series
D /E
Buttons
VOLUME Buttons
VOL
OK
OK Button
MENU
MENU Button
INPUT
INPUT Button
POWER Button
Remote Control Sensor
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates white when the set is switched on.
Owner’s Manual 7
Introduction
Location and Function of Controls
<Back Panel>
RS-232C IN
(CONTROL&SERVICE)
HDMI/DVI IN
REMOTE
CONTROL IN
RGB OUT
AUDIO
(RGB/DVI)
RGB
(PC/DTV)
RGB IN
1
R
L
2
3
1. RS-232C IN(CONTROL&SERVICE) PORT
Connect to the RS-232C port on a PC.
2. HDMI/DVI IN / AUDIO IN / RGB IN SOCKETS
Connect the set output socket of the PERSONAL
COMPUTER to this socket.
Note: If you want to use RGB/DVI audio, we strongly
recommend that you use the cable that has a core, or the EMI Filter core along
with separate cable.
RGB OUTPUT SOCKET
You can watch the RGB signal on another set, connect RGB OUT to another set’s
PC input port.
REMOTE CONTROL IN
VARIABLE AUDIO OUT SOCKETS
3. POWER CORD SOCKET
This set operates on an AC power. The voltage is
indicated on the Specifications page. Never attempt to
operate the set on DC power.
8 PLASMA TV
AC IN
VARIABLE
AUDIO OUT
Installation
External Equipment V iewing Setups
Connecting PC
- To enjoy vivid picture and sound, connect a PC to the set.
- Avoid keeping a fixed image on the set’s screen for a long period of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible.
- Connect PC to the RGB IN(PC IN) or HDMI-DVI IN(DIGITAL RGB IN) port of the set; change the resolution output of PC
accordingly.
- There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the
PC mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu
until the picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card.
- The synchronization input form for Horizontal and Vertical frequencies is separate.
Setup Instructions to Connect a PC to your set
- We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.
- In 42PC3MV series. 640x480p, 60Hz provide the best picture quality.
- If the resolution of PC is over UXGA, there will be no picture on the set.
- Connect the signal cable from the monitor output port of the PC to the RGB IN port of the set or the signal cable from the DVI
output port of the PC to the HDMI/DVI IN port on the set.
- Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set).
- If using a sound card, adjust PC sound as required.
- This set apply a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC
adjusts automatically to use this set.
- DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode.
- If required, adjust the set settings for Plug and Play functionally.
- If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB IN or
HDMI/DVI IN to display the PC on the set.
If graphic card on the PC output analog and digital RGB simultaneously, set the set to either RGB or HDMI; (the other mode
is set to Plug and Play automatically by the set.)
- DOS mode may not work depending on video card if using a DVI-I cable.
PC
1.
2.
3.
4.
Setup
Turn on the PC and apply power to the set.
Turn on the display by pressing the POWER button on the set.
Use the INPUT to select the RGB or HDMI input source.
Set the resolution output of the PC to SXGA or under (1280 x 1024, 60Hz).
Owner’s Manual 9
Installation
Displayable Monitor Specification
RGB / HDMI mode
Resolution
640x350
RGB / HDMI mode
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
31.468
70.09
31.469
70.08
37.927
85.03
59.94
31.469
59.94
35.000
66.66
35.000
66.66
37.861
72.80
37.861
72.80
37.500
75.00
37.500
75.00
43.269
85.00
43.269
85.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
35.156
56.25
35.156
56.25
37.879
60.31
37.879
60.31
48.077
72.18
48.077
72.18
46.875
75.00
46.875
75.00
53.674
85.06
53.674
85.06
49.725
74.55
49.725
74.55
48.363
60.00
48.363
60.00
56.476
70.06
56.476
70.06
60.023
75.02
60.023
75.02
68.677
85.00
68.677
85.00
54.348
60.05
47.700
60.00
63.995
70.01
59.625
75.02
67.500
75.00
47.700
60.00
1152x870
68.681
75.06
59.625
75.02
1280x960
60.023
60.02
54.348
60.05
1280x1024
63.981
60.02
63.995
70.01
67.500
75.00
68.681
75.06
47.693
59.99
848x480
852x480
800x600
832x624
1024x768
1152x864
42PC3MV series
31.469
70.08
37.927
85.03
31.469
640x350
85.08
640x480
85.08
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
31.468
70.09
37.861
720x400
37.861
Resolution
720x400
640x480
848x480
852x480
800x600
832x624
1024x768
1360x768
1366x768
1152x864
1152x870
1280x768
60.091
74.93
1280x960
60.023
60.02
1280x1024
63.981
60.02
42PC1M series
50PC1M series
10 PLASMA TV
Installation
-
HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing.
This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI).
This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
When you Connect with HDMI/DVI Source Devices (DVD Player or Set Top Box or PC) supporting Auto HDMI/DVI function, automatically, support Plug & Play and then set the HDMI/DVI Source Devices 1280 x 720p (or 42PC3MV series:
640x480p). After reading in HDMI/DVI Source Devices using Display Data Channel(DDC) Protocol, EDID stored in the set
is used. If HDMI/DVI Source Devices not supported Auto HDMI/DVI is been, the Resolution is set, manually.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.(or 42PC3MV series:
640x480p)
- To get the best picture quality, adjust the PC graphics card to 1024 x 768 (or 42PC3MV series: 640x480p), 60Hz.
- When Source Devices have DVI Output Connector, you must connect audio with separated cable.
(Refer to <How to connect>)
How to connect
1. When Source Devices (DVD Player or Set Top Box) support HDMI.
- If Source Devices have HDMI Output Connector, Source Devices connect to the set with HDMI Cable .(not supplied with the
product).
- If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 1280 x 720p (or 42PC3MV
series: 640x480p). But if not, resolution divert Manually Setting for reference Manual of Source Devices.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p (or 42PC3MV series:
640x480p).
- Because HDMI sends Digital Video and Audio with one cable, need not especial Audio Cable for using HDMI Cable.
2. When Source Devices (DVD Player or Set Top Box) supports DVI.
- If Source Devices have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with
the product).
- If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in 1280 x 720p (or 42PC3MV
series: 640x480p). But if not, resolution divert Manually Setting for reference Manual of Source Devices.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p (or 42PC3MV series:
640x480p).
- In this case, Audio use other cable. When Source Devices have Analog Audio Output Connector, RGB/DVI Audio Input of
the set connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio.
3. When PC supports DVI.
- If PC have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the product).
- To get the best picture quality, adjust the PC graphics card to 1024 x 768 (or 42PC3MV series: 640x480p), 60Hz.
- Use the the set’s HDMI/DVI (VIDEO) for video connections, depending on your PC connector.
- If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input
or HDMI/DVI Input to display the PC on the set.
- If he graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI
Input; (the other mode is set to Plug and Play automatically by the set.)
- Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.
- In this case, Audio use other cable. When PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio
Input of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to normal Audio.
Owner’s Manual 11
Installation
Reference
Cable sample
HDMI Cable
(not supplied with the product)
Analog Audio Cable (RCA type)
(not supplied with the product)
HDMI to DVI Cable
(not supplied with the product)
Analog Audio Cable (Stereo to RCA type)
(not supplied with the product)
How to use
1.
2.
3.
4.
Connect the HDMI/DVI Source Devices(DVD Player or Set Top Box or PC) and the set.
Turn on the display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control.
Select HDMI/DVI Input source in Main Input option of PIP/DW menu.
Check the image on your set. There may be noise associated with the resolution, vertical pattern, contrast or brightness in
HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the
refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics
card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.
Notes:
- Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.
- Avoid keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible.
- When Source Devices are connected with HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position and Size
may not fit to Screen. As shown the lower picture, press the MENU button to adjust the screen Position of the set and contact an PC graphics card service centre.
- When Source Devices connected HDMI/DVI Input output the set Resolution(480p, 720p, 1080i), the set Display fit EIA/CEA861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center.
- In case HDMI/DVI Source Devices is not connected Cable or poor cable connection, "No Signal" OSD display in HDMI/DVI
input. And in case of Video Resolution not supported the set output in HDMI/DVI Source Devices, "No Signal" OSD display.
Refer to the Manual of HDMI/DVI Source Devices or contact your service center.
12 PLASMA TV
Operation
Turning on the Set
Turning on the set just after installation
1. Connect power cord correctly, the set is switched to standby mode.
2. Press the r / I, INPUT or
D
/
E
button on the set and then the set will switch on.
Turning on the set (power cord is still connected)
If the set was turned off with the r / I button on the set.
• Press the r / I, INPUT or
D
/
E
button on the set to turn the set on.
On-Screen Menu Language Selection
- The menus can be shown on the screen in the selected language. First select your language.
- This feature is not available in all countries.
1. Press the MENU button and then use
2. Press the G button and then use D /
E
D
/
E
button to select the SPECIAL menu.
button to select Language.
3. Press the G button and then use D / E button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your choice.
4. Repeatedly press the MENU button to return to normal viewing.
Owner’s Manual 13
Operation
Picture Menu Options
PSM (Picture Status Memory)
- This function adjusts the set to the best picture appearance.
- When adjusting picture options (contrast, brightness, colour, sharpness and tint (NTSC input only)) manually, PSM
is automatically changed to User.
1. Press the MENU button and then use
D /E
button to select the PICTURE menu.
2. Press the
G
button and then use D
/E
button to select PSM.
3. Press the
User.
G
button and then use D
/E
button to select Dynamic, Standard, Mild or
4. Picture options Dynamic, Standard and Mild are preset and programmed for good
picture quality at the factory and cannot be changed.
5. Repeatedly press the MENU button to return to normal viewing.
• Each press of
D
/
E
button changes the screen display as shown below.
Dynamic
Standard
Mild
User
CSM (Colour Status Memory)
- To initialize values (reset to default settings), select the Normal option.
1. Press the MENU button and then use
D /E
button to select the PICTURE menu.
2. Press the
G
button and then use D
/E
button to select CSM.
3. Press the
ture.
G
button and then use D
/E
button to select the desired colour tempera-
4. Repeatedly press the MENU button to return to normal viewing.
• Each press of
D
Cool
/
E
button changes the screen display as shown below.
Normal
Warm
User
Manual Colour Temperature Control
- You can adjust red, green, or blue to any colour temperature you prefer.
1. Press the MENU button and then use
2. Press the
G
button and then use
3. Press the
G
button and then use D
4. Press the
G
button and then use
D /E
D /E
button to select CSM.
button to select User.
/E
D /E
button to select the PICTURE menu.
button to make appropriate adjustments.
5. Repeatedly press the MENU button to return to normal viewing.
- You can enjoy the vivid and hi-definition picture with LG’s Excellent Digital Reality processor technology.
- It’s not available to use this function in RGB[PC], HDMI[PC] mode.
- When selecting picture options (Dynamic, Standard and Mild) in PICTURE menu, XD is automatically changed
to On.
1. Press the MENU button and then use
2. Press the
G
button and then use D
3. Press the
G
button and then use
D /E
/E
D /E
button to select the PICTURE menu.
button to select XD.
button to select On or Off.
4. Repeatedly press the MENU button to return to normal viewing.
14 PLASMA TV
Operation
sRGB
- When the set is connected to external equipment with the sRGB function, the colour difference is adjusted the
equal image of each other.
- This function works in the following mode : RGB[PC], HDMI[PC].
1. Press the MENU button and then use
2. Press the
G
button and then use D
3. Press the
G
button and then use
D /E
/E
D /E
button to select the PICTURE menu.
button to select sRGB.
button to select On or Off.
4. Repeatedly press the MENU button to return to normal viewing.
ACM (Active Colour Management)
- Adjust the ACM to select the desired skin colour option.
- This function is not available for use in RGB[PC], HDMI[PC] mode.
- It’s not available to use this function in XD Off mode.
1. Press the MENU button and then use
D /E
button and then use
D /E
3. Press the G button and then use
F /G
2. Press the
G
button to select the PICTURE menu.
button to select ACM.
button to make appropriate adjustments.
4. Repeatedly press the MENU button to return to normal viewing.
Manual Picture Control
- You can adjust picture contrast, brightness, colour, sharpness and tint (NTSC input only) to the levels you prefer.
- It’s not available to use colour, sharpness function in RGB[PC], HDMI[PC] mode.
- In the broadcasting system PAL/SECAM, the picture item Tint doesn’t work.
1. Press the MENU button and then use
D /E
button to select the PICTURE menu.
2. Press the G button and then use D / E button to select the desired picture option.
(Contrast, Brightness, Colour or Sharpness)
3. Press the G button and then use
F /G
button to make appropriate adjustments.
4. Repeatedly press the MENU button to return to normal viewing.
Owner’s Manual 15
Operation
Sound Menu Options
SSM (Sound Status Memory)
- This function lets you enjoy the best sound without any special adjustment because the set automatically selects the
appropriate sound option based on the program content.
- When adjusting sound options (treble and bass) manually, SSM is automatically changed to User.
1. Press the MENU button and then use
2. Press the
G
button and then use
D /E
D /E
3. Press the G button and then use
Movie, Sports or User.
button to select the SOUND menu.
button to select SSM.
D / E
button to select SRS TSXT, Flat, Music,
4. The sound SRS TSXT, Flat, Music, Movie and Sports are programmed for good
sound reproduction at the factory and cannot be changed.
5. Repeatedly press the MENU button to return to normal viewing.
• Each press of
D
/
SRS TSXT
E
button changes the screen display as shown below.
Flat
Music
Movie
Sports
User
R
-
TruSurround XT
is a trademark of SRS Labs, Inc.
- TruSurround XT technology is incorporated under license from SRS Labs, Inc.
AVL (Auto Volume Leveler)
- This feature maintains an equal volume level; even if you change channels.
1. Press the MENU button and then use
D /E
button to select the SOUND menu.
2. Press the
G
button and then use
D /E
button to select AVL.
3. Press the
G
button and then use
D /E
button to select On or Off.
4. Repeatedly press the MENU button to return to normal viewing.
Adjusting Sound Control
1. Press the MENU button and then use D
/E
button to select the SOUND menu.
2. Press the G button and then use
(Balance, Treble or Bass)
D /E
button to select the desired sound item.
button and then use
F /G
button to make appropriate adjustments.
3. Press the
G
4. Repeatedly press the MENU button to return to normal viewing.
Note : Treble or Bass aren’t suitable to use SRS TSXT.
Speaker
- You can adjust the internal speaker status.
- In RGB[PC] and HDMI[PC] mode, Speaker and/or variable audio can be outputted even though there is no video signal.
- If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.
1. Press the MENU button and then use
D /E
button to select the SOUND menu.
2. Press the
G
button and then use
D /E
button to select Speaker.
3. Press the
G
button and then use
D /E
button to select On or Off.
4. Repeatedly press the MENU button to return to normal viewing.
16 PLASMA TV
Operation
T ime Menu Options
Setting the Clock
- If current time setting is erased by a power failure or the set is unplugged, reset the clock.
1. Press the MENU button and then use
D
2. Press the
G
button and then use
D
/
E
button to select Clock.
3. Press the
G
button and then use
D
/
E
button to adjust the hour.
/
E
button to select the TIME menu.
G button and then use D / E button to adjust the minute.
5. Repeatedly press the MENU button to return to normal viewing.
4. Press the
Setting the On/Off Timer
- Timer function operates only if current time has been already set.
- Off Timer function overrides on Timer function if they are set to the same time.
- The set must be in standby mode for the On Timer to work.
1. Press the MENU button and then use
D
/
E
button to select the TIME menu.
2. Press the
G
button and then use
D
/
E
button to select Off time or On time.
3. Press the
G
button and then use
D
/
E
button to select On.
4. Press the
G
button and then use
D
/
E
button to adjust the hour.
5. Press the
G
button and then use
D
/
E
button to adjust the minute.
6. Only On time function; Press the G button and then use D / E button to adjust volume level.
7. Repeatedly press the MENU button to return to normal viewing.
- To cancel Off/On time function
Press the D / E button to select Off in step 3.
Auto Sleep
- If there is no input signal, the set turn off automatically after 10 minutes.
1. Press the MENU button and then use
2. Press the G button and then use
D
/
D
E
/
E
button to select the TIME menu.
button to select Auto sleep.
3. Press the G button and then use
D / E button to select On or Off.
4. Repeatedly press the MENU button to return to normal viewing.
Owner’s Manual 17
Operation
Special Menu Options
Child Lock
- The set can be set up so that it can’t be used with the button on the set.
1. Press the MENU button and then use
2. Press the
G
button and then use
D
/
3. Press the G button and then use D /
D
E
E
/
button to select the SPECIAL menu.
E
button to select Child lock.
button to select On or Off.
4. Repeatedly press the MENU button to return to normal viewing.
- This set is programmed to remember which option it was last set to even if you turn the set off.
- In Child lock ‘On’, if the set is turned off, press the INPUT button on the set.
- With the Child lock On, the display ‘ Child lock on’ appears on the screen if any button on the front panel is
pressed while viewing the set.
ISM (Image Sticking Minimization) Method
- Frozen of still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost
image remaining even when you change the image. Avoid allowing a fixed image to remain on the set's screen for
a long period of time.
1. Press the MENU button and then use
2. Press the
G
button and then use
D /E
D /E
button to select the SPECIAL menu.
button to select ISM Method.
3. Press the G button and then use D / E button to select either Normal, White wash,
Orbiter or Inversion. If you unnecessary to set this function, set Normal.
• White Wash :
White Wash removes permanent images from the screen.
Note: An excessive permanent image may be impossible to clear entirely with White
Wash.
• Orbiter :
Orbiter may help prevent ghost images. However, it is not best to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
screen will move every 2 minutes.
• Inversion :
This is the function to invert the panel colour of the screen. The panel colour is automatically inverted every 30 minutes.
4. Repeatedly press the MENU button to return to normal viewing.
Low Power
- This is the function to reduce the power consumption of the set.
1. Press the MENU button and then use
2. Press the
G
button and then use
3. Press the G button and then use
D /E
D /E
D /E
button to select the SPECIAL menu.
button to select Low power.
button to select On or Off.
4. Repeatedly press the MENU button to return to normal viewing.
Demo
- Use it to see the difference between XD Demo on and XD Demo off.
- It’s not available to use this function in RGB[PC], HDMI[PC] mode.
1. Press the MENU button and then use
D /E
2. Press the
G
button and then use
3. Press the
G
button to begin XD Demo.
D /E
button to select XD Demo.
4. To stop XD Demo, press the MENU button.
18 PLASMA TV
button to select the SPECIAL menu.
Operation
Screen Menu Options
Auto Configure
- Automatically adjusts picture position and minimizes image shaking.
- This function works in the following mode : RGB[PC] mode only
1. Press the MENU button and then use
2. Press the
G
button and then use
D
/
D
E
/
E
button to select the SCREEN menu.
button to select Auto config..
3. Press the G button to start Auto config..
• When Auto config. has finished, Ok will be shown on screen.
• If the position of the image is still not correct, try Auto adjustment again.
4. If picture needs to be adjusted more after Auto adjustment in RGB (PC), you can adjust
the Manual Config..
5. Repeatedly press the MENU button to return to normal viewing.
- Although the image is still not correct, your set is functioning properly but needs further adjustment.
- The Auto config. functions don’t need to be run for HDMI mode.
Manual Configure
- If the picture isn’t clear after auto adjustment and especially that characters are still trembling, adjust the picture phase
manually.
- To correct the screen size, adjust Clock.
- This function works in the following mode:
RGB[PC], RGB[DTV], HDMI[DTV] mode only
- It’s not available to use Phase, Clock function in RGB[DTV], HDMI[DTV] mode.
1. Press the MENU button and then use
2. Press the
G
button and then use
D
/
D
E
/
E
button to select the SCREEN menu.
button to select Manual config..
3. Press the G button and then use D / E button to select Phase, Clock, H-Position
or V-Position.
4. Press the
F
/
G
button to make appropriate adjustments.
5. Repeatedly press the MENU button to return to normal viewing.
Selecting Wide VGA/XGA mode
- To see a normal picture, match the resolution of RGB mode and selection of VGA/XGA mode.
- In some models, it’s not available to selection of XGA mode.
- This function works in the following mode : RGB[PC] mode only
1. Press the MENU button and then use
2. Press the G button and then use
D
D
/ E button to select the SCREEN menu.
/ E button to select VGA Mode (or XGA Mode).
3. Press the G button and then use D / E button to select the desired VGA/XGA resolution.
4. Repeatedly press the MENU button to return to normal viewing.
Owner’s Manual 19
Operation
Screen Menu Options
Setting the Picture Format
- You can watch the screen in various picture formats; Spectacle, Full , Original, 4:3, 16:9 (Wide), 14:9 and Zoom.
1. Press the MENU button and then use
2. Press the
G
button and then use
3. Press the G button and then use
4:3, 16:9, 14:9 or Zoom.
D
D
/
D
/
E
button to select the SCREEN menu.
button to select ARC.
E
/ E button to select Spectacle, Full , Original,
• Spectacle
When your TV receives the wide screen signal, following selection will lead you to adjust
the picture horizontally, in non-linear proportion, to fill the entire screen.
• Full (This feature is not available in all countries.)
When your TV receives the wide screen signal, when selected it will lead you to adjust
the picture horizontally or vertically, in a linear proportion, to fill the entire screen fully.
• Original
When your TV receives the wide screen signal, it will be automatically changed to the
picture format to be sent.
• 4:3
Following selection will lead you to view a picture with an original 4:3 aspect ratio, with
gray bars appearing at both the left and right sides.
• 16:9 (Wide)
Following selection will lead you to adjust the picture horizontally, in a linear proportion,
to fill the entire screen (useful for viewing 4:3 formatted DVDs).
• 14:9
You can enjoy the picture format of 14:9 or general TV programme through the 14:9
mode. The screen 14:9 is viewed just like that the screen 4:3 is magnified to the left /
right.
• Zoom
Following selection will lead you to view the picture without any alternation, while filling
the entire screen. However, the top and bottom portions of the picture will be cropped.
4. Repeatedly press the MENU button to return to normal viewing.
- You can only select 4:3 and 16:9 (Wide) in RGB[PC], HDMI[PC] mode only.
- You can only select 4:3, 16:9 (Wide) and Zoom in RGB[DTV], HDMI[DTV] mode only.
- There might be uncomfortable in full mode. Then change into other mode.
Picture Size Zoom
- When enlarging or reducing the picture, the screen may be display unnatural picture.
1. Press the MENU button and then use
D
2. Press the
G
button and then use
D
/
E
3. Press the
G
button and then use
F
/
G
/
E
button to select the SCREEN menu.
button to select Zoom + /-.
button to make appropriate adjustments.
4. Repeatedly press the MENU button to return to normal viewing.
20 PLASMA TV
Operation
Screen Position
- You are available to function after adjusting Zoom +/-.
1. Press the MENU button and then use
D
2. Press the
G
button and then use
D
/
E
3. Press the
G
button and then use
D
/
E
/
E
button to select the SCREEN menu.
button to select Position.
or
F
/
G
button to adjust the position.
4. Repeatedly press the MENU button to return to normal viewing.
Cinema
- When you watch the movie, this function adjusts the set to the best picture appearance.
1. Press the MENU button and then use
D
/ E button to select the SCREEN menu.
2. Press the
G
button and then use
D
/
E
button to select Cinema.
3. Press the
G
button and then use
D
/
E
button to select On or Off.
4. Repeatedly press the MENU button to return to normal viewing.
NR (Noise Reduction)
- You can select 3D NR or MPEG NR to reduce the picture noise which may appear on the screen during watching
the set.
- This function is not available for use in RGB[PC], HDMI[PC] mode.
- 3D NR is not available for use in RGB, HDMI mode.
1. Press the MENU button and then use
D
/ E button to select the SCREEN menu.
2. Press the G button and then use
D
/ E button to select NR.
3. Press the G button and then use
D
/ E button to select 3D NR or MPEG NR.
4. Press the
F
/
G
button to make appropriate adjustments.
5. Repeatedly press the MENU button to return to normal viewing.
Initializing (Reset to original factory value)
- This function operates in current mode.
- To initialize the adjusted value
1. Press the MENU button and then use
2. Press the G button and then use D /
E
D
/
E
button to select the SCREEN menu.
button to select Reset.
3. Press the G button.
• You can initialize Phase, Clock, H-Position, V-Position, Position, Zoom +/-.
Owner’s Manual 21
Operation
PIP (Picture-in-Picture) Feature
- PIP lets you view 2 different inputs (sources) on your set screen at the same time.
Watching PIP
RGB
AV1
RGB
AV1
RGB
AV1
10:30
10:30
10:30
RGB
C 05 1
RGB
10:30
10:30
Note :
a. When the sub picture size is 1/2 of the main picture, the picture quality may decrease.
b. The motion of the sub picture can be unnatural because the set displays full screen by synchronizing the main picture source when
the refresh rate between the main picture source and the sub picture source is different in PIP mode.
Selecting an Input Signal Source for the PIP
1. Press the MENU button and then use
D
/
E
button to select the PIP/DW menu.
2. Press the
G
button and then use
D
/
E
button to select PIP Input.
3. Press the
G
button and then use
F
/
G
button to select input source for sub picture.
4. Repeatedly press the MENU button to return to normal viewing.
In some models, when the sub picture quality get poor for sub picture, select Auto, PAL, SECAM or NTSC in PIP System menu.
Picture Size
1. Press the MENU button and then use
2. Press the
G
button and then use
D
/
D
E
/
E
button to select the PIP/DW menu.
button to select Win. size.
3. Press the G button and then use F / G button to adjust the sub picture size.
In DW1, DW2 modes, main and sub picture is adjusted simultaneously. In PIP mode, sub picture is adjusted.
4. Repeatedly press the MENU button to return to normal viewing.
Moving the PIP (PIP mode only)
1. Press the MENU button and then use
2. Press the
G
button and then use
D
/
D
E
/
E
button to select the PIP/DW menu.
button to select Win. position.
3. Press the G button and then use D / E / F /
The sub picture moves up/down or left/right.
G
button to adjust position for sub picture.
4. Repeatedly press the MENU button to return to normal viewing.
Adjusting PIP Transparency (PIP mode only)
1. Press the MENU button and then use
2. Press the
G
button and then use
D
3. Press the
G
button and then use
F
D
/
E
button to select the PIP/DW menu.
/
E
button to select PIP Transparency.
/
G
button to adjust PIP transparency.
4. Repeatedly press the MENU button to return to normal viewing.
22 PLASMA TV
Miscellaneous
External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)
and control the set’s functions externally.
How to connect external control equipment
• Connect the serial port of the control device to the RS-232C jack on the back panel.
• RS-232C connection cables are not supplied with the set.
• The set remote control and front panel controls (except main power) will not be functional if the set is controlled by a PC
computer or other external device.
Type of connector; D-Sub 9-pin male
No.
1
2
3
4
5
6
7
8
9
1
Pin name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
5
9
6
RS-232C configurations
3-wire configuration
(Not standard)
7-wire configuration
(Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
Plasma Monitor
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
Plasma Monitor
2
3
5
4
6
7
8
3
2
5
4
6
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Owner’s Manual 23
Miscellaneous
Set ID
- Use this function to specify a set ID number.
- Refer to ‘Real Data Mapping 1’. See page 28.
1. Press the MENU button and then use
2. Press the
D /E
button and then use
D /E
3. Press the G button and then use
monitor ID number.
F /G
G
button to select the SPECIAL menu.
button to select Set ID.
button to adjust Set ID to choose the desired
• The adjustment range of Set ID is 1 ~ 99.
4. Repeatedly press the MENU button to return to normal viewing.
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
* Use a crossed (reverse) cable.
• Stop bit : 1 bit
• Communication code : ASCII code
Command Reference List
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Colour
10. Tint
11. Sharpness
12. OSD Select
13. Remote control lock mode
14. PIP/DW
15. PIP Position
16. Treble
17. Bass
18. Balance
19. Colour Temperature (CSM)
20. Red Adjustment
21. Green Adjustment
22. Blue Adjustment
23. PIP input Select
24. Abnormal Status
25. ISM Method
26. Low Power
27. Orbiter Time Setting
28. Orbiter Pixel Setting
29. Picture Size
30. Auto Configure
31. Send IR Code
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
j
j
j
j
j
m
a
b
c
d
e
f
g
h
i
j
k
l
m
n
q
r
s
t
u
v
w
$
y
z
p
q
r
s
t
u
c
0~1
Refer to p. 25
Refer to p. 25
0~ 1
0~ 1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0~1
0~1
Refer to p. 26
0~3
0 ~ 64
0 ~ 64
0 ~ 64
0~3
0 ~ 50
0 ~ 50
0 ~ 50
Refer to p. 27
0~a
0~3
0~1
1 ~ FE
1~3
0 ~ 20
1
Key Code
* When setting the 24 ~ 31, a menu doesn’t display on screen.
24 PLASMA TV
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]
* [Command 2]
* [Set ID]
* [DATA]
* [Cr]
* [ ]
: First command to control Plasma
Monitor set.
(j, k, m or x)
: Second command to control Plasma
Monitor set.
: You can adjust the set ID to choose
desired monitor ID number in special
menu. Adjustment range is 1 ~ 99.
When selecting Set ID ‘0’, every connected
Plasma Monitor set is controlled.
Set ID is indicated as decimal (1~99) on
menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
: To transmit command data.
Transmit ‘FF’ data to read status of
command.
: Carriage Return
ASCII code ‘0x0D’
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this
format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this
format when receiving abnormal data from
non-viable functions or communication errors.
Data 1: Illegal Code
2: not support function
3: Wait more time
Miscellaneous
01. Power (Command 2 : a)
05. Volume Mute (Command 2 : e)
G To control Power On/Off of the set.
G To control volume mute on/off.
Transmission
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
1 : Power On
Ack
Data 0 : Volume mute off (Volume on)
1 : Volume mute on (Volume off)
[a][ ][Set ID][ ][OK][Data][x]
Ack
G To show Power On/Off.
[e][ ][Set ID][ ][OK][Data][x]
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
06. Volume Control (Command 2 : f)
Ack
[a][ ][Set ID][ ][OK][Data][x]
* In like manner, if other functions transmit ‘0xFF’ data
based on this format, Acknowledgement data feed back
presents status about each function.
G To adjust volume.
You can also adjust volume with the volume buttons
on the set.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
02. Input Select (Command 2 : b)
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 28.
G To select input source for the set.
Ack
[f][ ][Set ID][ ][OK][Data][x]
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
07. Contrast (Command 2 : g)
Data 0 : RGB
1 : HDMI
G To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Ack
[b][ ][Set ID][ ][OK][Data][x]
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
03. Aspect Ratio (Command 2 : c)
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 28.
Ack
[g][ ][Set ID][ ][OK][Data][x]
G To adjust the screen format. (Main picture format)
You can also adjust the screen format in the SCREEN
menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 1
2
3
4
:
:
:
:
Normal screen (4:3)
Wide screen (16:9)
Spectacle
Zoom
6 : Original
7 : Wide screen (14:9)
8 : Full
Ack
[c][ ][Set ID][ ][OK][Data][x]
08. Brightness (Command 2 : h)
G To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 28.
Ack
* Using the PC input, you select either 16:9 or 4:3 screen
aspect ratio.
[h][ ][Set ID][ ][OK][Data][x]
04. Screen Mute (Command 2 : d)
09. Colour (Command 2 : i)
G To select screen mute on/off.
G To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Ack
[d][ ][Set ID][ ][OK][Data][x]
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 28.
Ack
[i][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 25
Miscellaneous
10. Tint (Command 2 : j)
15. PIP Position (Command 2 : q)
G To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
G To select sub picture position for PIP.
You can also adjust the sub picture position in the PIP/DW
menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0 ~ Green : 64
* Refer to ‘Real data mapping 1’. See page 28.
Ack
[j][ ][Set ID][ ][OK][Data][x]
Transmission
[k][q][ ][Set ID][ ][Data][Cr]
Data 0
1
2
3
:
:
:
:
Right down on screen
Left down on screen
Left up on screen
Right up on screen
Ack
11. Sharpness (Command 2 : k)
[q][ ][Set ID][ ][OK][Data][x]
G To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
16. Treble (Command 2 :r)
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 28.
G To adjust treble.
You can also adjust treble in the SOUND menu.
Transmission
Ack
[k][r][ ][Set ID][ ][Data][Cr]
[k][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 28.
Ack
12. OSD Select (Command 2 : l)
G To select OSD (On Screen Display) on/off when controlling remotely.
17. Bass (Command 2 : s)
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0 : OSD off
[r][ ][Set ID][ ][OK][Data][x]
1 : OSD on
Ack
G To adjust bass.
You can also adjust bass in the SOUND menu.
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
[l][ ][Set ID][ ][OK][Data][x]
13. Remote control lock mode (Command 2 : m)
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 28.
Ack
G To lock the front panel controls on the set and remote
control.
[s][ ][Set ID][ ][OK][Data][x]
Transmission
18. Balance (Command 2 : t)
[k][m][ ][Set ID][ ][Data][Cr]
Data 0 : Lock off
1 : Lock on
G To adjust balance.
You can also adjust balance in the SOUND menu.
Ack
[m][ ][Set ID][ ][OK][Data][x]
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
* If you’re not using the remote control, use this mode.
When main power is on/off, external control lock is
released.
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 28.
Ack
[t][ ][Set ID][ ][OK][Data][x]
14. PIP / DW (Command 2 : n)
G To control the PIP (Picture In picture)/DW.
You can also control the PIP/DW in the PIP/DW menu.
19. Colour Temperature (Command 2 : u)
Transmission
[k][n][ ][Set ID][ ][Data][Cr]
G To adjust colour temperature.
You can also adjust CSM in the PICTURE menu.
Data 0: PIP/DW off
1: PIP
2: DW1
3: DW2
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Ack
Data 0: Cool
[n][ ][Set ID][ ][OK][Data][x]
Ack
1: Normal
[u][ ][Set ID][ ][OK][Data][x]
26 PLASMA TV
2: Warm
3: User
Miscellaneous
20. Red Adjustment (Command 2 : v)
24. Abnormal State (Command 2 : z)
G To adjust red in colour temperature.
G To recognize an abnormal state.
Transmission
Transmission
[k][v][ ][Set ID][ ][Data][Cr]
[k][z][ ][Set ID][ ][FF][ ][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 28.
Data FF : Read
Ack
[v][ ][Set ID][ ][OK][Data][x]
21. Green Adjustment (Command 2 : w)
G To adjust green in colour temperature.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 28.
Ack
[w][ ][Set ID][ ][OK][Data][x]
22. Blue Adjustment (Command 2 : $)
G To adjust blue in colour temperature.
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Ack
[z][ ][Set ID][ ][OK][Data][x]
Data 0: Normal (Power on and signal exist)
1: No signal (Power on)
2: Turn the set off by remote control
3: Turn the set off by sleep time function
4: Turn the set off by RS-232C function
5: 5V down
6: AC down
7: Turn the set off by Fan Alarm function
8: Turn the set off by Off time function
9: Turn the set off by Auto sleep function
a: Turn the set off by AV board detect
* This function is “read only”.
25. ISM Method
(Command 1 : j, Command 2 : p)
G To control the ISM method. You can also adjust ISM
Method in SPECIAL menu.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 28.
Ack
Data 0 : Normal Mode
1 : White Wash
[$][ ][Set ID][ ][OK][Data][x]
Ack
2 : Orbiter
3 : Inversion
[p][ ][Set ID][ ][OK][Data][x]
23. PIP Input Select (Command 2 : y)
G To select input source for sub picture in PIP/DW picture mode.
Transmission
[k][y][ ][Set ID][ ][Data][Cr]
Data 0 : RGB
1 : HDMI
Ack
[y][ ][Set ID][ ][OK][Data][x]
26. Low Power
(Command 1 : j, Command 2 : q)
G To reduce the power consumption of the set. You can
also adjust Low Power in SPECIAL menu.
Transmission
[j][q][ ][Set ID][ ][Data][ ][Cr]
Data 0 : Off
1 : On
Ack
[q][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 27
Miscellaneous
27. Orbiter Time Setting
(Command 1 : j, Command 2 : r)
30. Auto Configure
(Command 1 : j, Command 2 : u)
G To adjust orbiter operation time term.
G To adjust picture position and minimize image shaking
automatically. It works only in RGB(PC) mode.
Transmission
[j][r][ ][Set ID][ ][Data][ ][Cr]
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: FE
* Refer to ‘Real data mapping 1’.
Data 1: To set
Ack
Ack
[r][ ][Set ID][ ][OK][Data][x]
[u][ ][Set ID][ ][OK][Data][x]
28. Orbiter Pixel Setting
(Command 1 : j, Command 2 : s)
31. Send IR Code
(Command 1 : m, Command 2 : c)
G To adjust pixel number in orbiter function.
G To send IR remote key code.
Transmission
Transmission
[j][s][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: 3
* Refer to ‘Real data mapping 1’.
Ack
[s][ ][Set ID][ ][OK][Data][x]
[m][c][ ][Set ID][ ][Data][Cr]
Data Key code - Refer to page 30.
Ack
[c][ ][Set ID][ ][OK][Data][x]
* Real data mapping 1
29. Picture Size Setting for DW Mode
(Command 1 : j, Command 2 : t)
0 : Step 0
G To select the DW picture format.
You can also select the DW picture format using the
SIZE on the remote control.
A : Step 10 (Set ID 10)
Transmission
F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
[j][t][ ][Set ID][ ][Data][Cr]
64 : Step 100
Data Min: 0 ~ Max: 20
* Refer to ‘Real data mapping 1’.
6E : Step 110
Ack
[t][ ][Set ID][ ][OK][Data][x]
73 : Step 115
74 : Step 116
C7 : Step 199
FE : Step 254
FF : Step 255
28 PLASMA TV
* Real data mapping 2
0 : -40
1 : -39
2 : -38
28 : 0
4E : +38
4F : +39
50 : +40
Miscellaneous
IR Code (NEC Format)
How to connect
G Connect your wired remote control to the Remote Control port on the set.
Remote Control IR Code (NEC Format)
G Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
TC
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
G Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
G Lead code
9 ms
4.5 ms
0.55 ms
G Repeat code
9 ms
2.25 ms
G Bit description
• Bit “0”
• Bit “1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
G Frame interval : Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
Owner’s Manual 29
Miscellaneous
Code (Hexa)
00
01
02
03
40
41
06
07
08
C4
C5
09
10
11
12
13
14
15
16
17
18
19
0B
98
BF
D4
C6
D5
D6
5A
D8
0A
0E
43
44
53
20
2A
22
24
26
64
65
70
79
76
77
AF
60
61
63
71
72
5C
5D
E0
E1
1A
1E
62
30 PLASMA TV
Function
UP(D)
DOWN(E)
VOL (D)
VOL (E)
D
E
G
F
POWER
POWER ON
POWER OFF
MUTE
Number Key 0
Number Key 1
Number Key 2
Number Key 3
Number Key 4
Number Key 5
Number Key 6
Number Key 7
Number Key 8
Number Key 9
INPUT
MULTIMEDIA
COMPONENT1
COMPONENT2
HDMI
RGB
TV
AV
S-Video
I/II
SLEEP
MENU
OK( )
LIST/
TEXT/
REVEAL
MODE
MIX
TIME
SIZE
HOLD
INDEX
ARC
ARC (4:3)
ARC (16:9)
ARC (Zoom)
PIP
PIP INPUT
SWAP
PIP PR+
PIP PRZoom +
Zoom +
Q.VIEW/
FAV/
POSITION
*
*
*
*
Note
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power On/Off)
Discrete IR Code (Only Power On)
Discrete IR Code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Input COMPONENT1 Selection)
Discrete IR Code (Input COMPONENT2 Selection)
Discrete IR Code (Input HDMI Selection)
Discrete IR Code (Input RGB Selection)
Discrete IR Code (Input TV Selection)
Discrete IR Code (Input AV Selection)
Discrete IR Code (Input S-Video Selection)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Only 4:3 mode)
Discrete IR Code (Only 16:9 mode)
Discrete IR Code (Only Zoom mode)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Miscellaneous
Notes
Owner’s Manual 31
Miscellaneous
Notes
32 PLASMA TV
Miscellaneous
Notes
Owner’s Manual 33
Miscellaneous
Troubleshooting Checklist
• Check whether the set is turned on.
No picture &
No sound
• Power cord inserted into wall outlet?
• Plug another product’s power cord into the wall outlet where the set’s power
cord was plugged in.
• Press the VOLUME (G) button.
Picture OK &
No sound
• Sound muted? Press MUTE button.
• Check whether the Speaker is “on” in the SOUND menu.(Refer to p. 16)
Picture appears slowly,
after switching on
• This is normal as the image is muted during the startup process of the set.
Please contact your service centre, if the picture has not appeared after five
minutes.
• Select Colour in the PICTURE menu and press the
(Refer to p.15)
No or Poor colour
or Poor picture
G
button.
• Keep a certain distance between the set and the VCR.
• Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the screen gets dark.)
Horizontal/vertical bars
or picture shaking
No output from one of the
speakers
Unusual sound from
inside the set
34 PLASMA TV
• Check for local interference such as an electrical appliance or power tool.
• Adjust Balance in the SOUND menu. (Refer to p.16)
• A change in ambient humidity or temperature may result in an unusual noise
at the time of switching off or on of the set and does not indicate a fault with
the set.
Miscellaneous
Product Specifications
MODELS
with stand
42PC1M*
42PC3MV*
50PC1M*
42PC1M-TA
42PC1MH -TA
42PC3MV-TA
42PC3MVH -TA
50PC1M-TA
50PC1MH -TA
1129.0 x 748.5 x 380.0 mm 1129.0 x 748.5 x 380.0 mm 1302.6 x 872 x 355.8 mm
44.4 x 29.5 x 15.0 inches
Dimensions
44.4 x 29.5 x 15.0 inches
51.3 x 34.3 x 14.0 inches
(Width x Height x Depth)
without stand
Weight
1129.0 x 695.0 x 103.7 mm 1129.0 x 695.0 x 103.7 mm 1302.6 x 810x 108.7 mm
44.4 x 27.4 x 4.0 inches
44.4 x 27.4 x 4.0 inches
51.3 x 31.9 x 4.3 inches
including stand
28.5 kg/62.8 lbs
28.3 kg/62.4 lbs
50.46 kg/111.2 lbs
excluding stand
24.5 kg/54.0 lbs
24.3 kg/53.6 lbs
41.66 kg/91.8 lbs
Power requirement
AC100-240V~ 50/60Hz
Television System
PAL/BG/DK/I, NTSC-M
External Antenna Impedance
75 ohm
Operating Temperature
Environment condition
Operating Humidity
Storage Temperature
Storage Humidity
•
0 ~ 40°C / 32 ~ 104°F
Less than 80%
-20 ~ 60°C / -4 ~ 140°F
Less than 85%
The specifications shown above may be changed without notice for quality improvement.
Owner’s Manual 35
Download PDF

advertising