LG | LAC3700R | LG LAC3700R Owner’s Manual

LAC3700R_ENG_CZ
LAC3700R/ 3705R/ 3710R/ 3715R
ENGLISH
CAR CD/MP3/WMA Receiver
Read the manual carefully before using the unit
POLISH
Odbiornik samochodowy CD/MP3/WMA
Przed przystąpieniem do obsługi urządzenia, przeczytaj
dokładnie niniejszą instrukcję obsługi.
CZECH
Auto CD/MP3/WMA přijímač
Před použitím přístroje si pozorně přečtěte tuto příručku
SLOVAK
Auto CD/MP3/WMA prijímač
Pred použitím jednotky si tento manuál pozorne prečítajte.
HUNGARIAN
Autórádió-CD/MP3/WMA-lejátszó
A készülék használata előtt gondosan olvassa el ezt a
kézikönyvet.
P/NO : MFL40795786
Safety note
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT SPLIT COVER(OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with the arrowhead symbol, within an equilateral
triangle is intended to alert the user about the presence of uninsulated dangerous
voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Always operate the vehicle in a safe manner.
Do not become distracted by the vehicle while driving, and always be fully aware of
all driving condition. Do not change settings, or any functions.
Pull over in a safe and legal manner before attempting such operations.
Do not use for many hours at extremely low or high temperature.
(-10~60°C)
To reduce the risk of electric shock, do not remove the cover or back of this product. There are no user-serviceable parts inside.
Refer servicing to qualified service personnel.
To reduce the risk of fire or electric shock, do not expose this product to dripping or
splashing water, rain, or moisture.
The temperature of unit’s outside can be extremely high, please use the unit after
proper installation in your vehicle.
CAUTION : This product uses a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain it
for future reference.
Should the unit require maintenance, contact an authorized service center.
Performing controls, adjustments, or carrying out procedures other than those specified
herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser
radiation when open. DO NOT STARE INTO BEAM.
2
• A defective or soiled disc inserted into unit can cause sound to drop out
during playback.
• Handle the disc by holding its inner and outer edges.
• Do not touch the surface of the unlabeled side of the disc.
Do not stick paper or tape etc. on the surface.
Do not expose the disc to direct sunlight or excessive heat.
8 cm
This unit cannot play 8cm disc (use 12cm disc only).
• Clean the disc before playback. Wipe the disc from the center outward
with a cleaning cloth.
• Never use solvents such as benzine or alcohol to clean the disc.
Periodically wipe the contacts on the back of the control panel with a
cotton swap moistened with alcohol.
A section whose title has one of the following symbols is applicable only to the disc
represented by the symbol.
CD
Audio CDs
MP3
MP3 files
WMA WMA files
MP3/WMA Disc compatibility with this unit is limited as follows:
1.
2.
3.
4.
Sampling Frequency / 8 - 48kHz (MP3) 22.05 - 48kHz (WMA)
Bit rate / within 8 - 320kbps (include VBR) (MP3) 32 -320kbps (WMA)
CD-R/CD-RW file system should be “ISO 9660”
If you record MP3/WMA files using software which cannot create a FILE SYSTEM, for example
“Direct-CD” etc., it will not be possible to playback MP3/WMA files. We recommend that you use
“Easy-CD Creator” which creates an ISO9660 file system.
Customers should also note that permission is required in order to download MP3/WMA files and
music from the Internet.
Our company has no right to grant such permission.
Permission should always be sought from the copyright owner.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product, it means the product is
covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal
waste stream via designated collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please
contact your city office, waste disposal service or the shop where you purchased the product.
This product is manufactured to comply with Directive 2005/83/EEC(ANNEX I , 3.2.9),
72/245/EEC, and 2006/95/EC.
3
Table of contents
Safety note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Remote control (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8
Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-11
Radio operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
RDS operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
CD/MP3/WMA operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Before use
Detaching the control panel
The control panel of this unit can be detached to prevent theft.
1 Press the “ ” (RELEASE) to open the control panel.
2 Hold the right part of the control panel.
3 Pull out the control panel.
4 Place the control panel in the supplied protective case.
1
4
3
2
Attachable control panel
Control panel
1
2
Protective Case
Align the left side of the panel with the stopper.
Push the right side or panel into the unit until it clicks.
Caution
• The control buttons may not work properly if the control
panel is not attached properly. If this occurs, gently press
the display.
• Do not leave the control panel in any area exposed to high
temperatures or direct sunlight.
• Do not drop the control panel or otherwise subject it to
strong impact.
2
1
• Do not allow such volatile agents as benzine, thinner, or
insecticides to come into contact with the surface of the
control panel.
4
Control panel
1
2
3
4
5
6
7
8
EJECT Z
Alternative frequency
[AF(REG)]
Traffic Announcement [TA]
Remote Sensor - Optional
• Volume
• [MUTE]
• Power [PWR]
• Auto Store [AS]
• Preset Scan [PS]
• Equalizer [EQ]
9
10
11
12
13
14
DISC SLOT
• Skip / Search B[ +
• Seek/ Tune B[ +
Display [DISP]
Release
Select [SEL S ]
• Skip / Search - [b
• Seek/ Tune - [b
Preset Station [1-6]
• MP3 Track +10/-10
[F+/F-] MP3 WMA
• Folder Up/Down [F+/F-]
MP3
WMA
15
16
17
18
19
Shuffle [SHF]
Repeat [RPT]
Intro Scan [SCAN]
Play/Pause B X
Extreme Dynamic Sound
System [XDSS]
20 [BAND]
21 Programme Type [PTY]
22 SOURCE [SRC S]
Remote control (optional)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
Power [POWER] / Mute
Select [SEL]
Source [SRC]
Play / Pause B/X
Intro Scan [SCAN]
Shuffle [SHF]
• MP3 Track +10
MP3
WMA
• Folder Up [F+]
15
16
17
MP3
8
WMA
• CD Skip
/ Search ?m m
• Seek / Tune ?m m
9
10
11
12
13
14
15
[BAND]
Volume Up
/ Down
Number [#]
Repeat [RPT]
Preset Station [1-6]
Number [0 -9]
• CD Skip
/ Search M M?
• Seek / Tune M M?
16 Display [DISP.]
17 • MP3 Track -10
MP3
• Folder Down [F-]
MP3
5
WMA
WMA
Battery Installation
1
2
3
Pull out the battery holder with a sharp product
like a ball point pen.
Put the battery with
and
correctly on the
battery holder.
Push the battery holder back into its original
position.
Note
• Use only one CR2025 (3V) lithium battery.
• Remove the battery if the remote control is not
used for a long period of time.
• Do not leave the product in a hot or humid place.
• Do not handle the battery with metallic tools.
• Do not store the battery with metallic materials.
Installation
Basic Installation
Before installing, make sure that the ignition-switch is set to
OFF and remove the terminal of the car battery to avoid
short-circuiting.
Bend the claws
according to
the thickness
of the
dashboard
1
2
3
4
Remove the existing receiver unit.
Make the necessary connections.
Install the installation sleeve.
Install the unit into the installation sleeve.
Control panel
Removing the existing receiver unit
If there is already an installation sleeve for the receiver unit
in the dashboard, it must be removed.
A
1
2
3
Remove the rear support from the unit.
Remove the control panel and trim ring from the unit.
Insert the lever A into the hole on one side of the unit.
Perform the same operation on the other side and pull
the unit out from the mounting sleeve.
1
2
3
4
5
6
Slide the unit into the ISO-DIN frame.
Fit screws removed from the old unit.
Slide the unit and frame into the dash opening.
Install the dash panel or adapter plate.
Install the trim ring to the unit.
Install the control panel to the unit.
A
ISO-DIN Installation
1
4
5
6
Control panel
3
2
6
Connection diagram
Before connecting, make sure that the ignition switch is set to OFF, and remove the battery #
terminal to avoid short circuits.
B
r
(Optional)
B
1
3
5
7
2
4
6
8
5
7
2
4
6
8
To Speaker
To Vehicle
A
A
(Optional)
A
2
B
B
B
B
B
B
B
B
PHONE MUTE (ORANGE)
A
8
GROUND(-) (BLACK)
A
6
DIMMER (PINK)
A
1.
2.
3.
4.
5.
6.
7.
8.
Violet : Rear Right +
Violet/ Black Stripe : Rear Right –
Gray : Front Right +
Gray / Black Stripe : Front Right –
White : Front Left +
White/Black Stripe : Front Left –
Green : Rear Left +
Green/ Black Stripe : Rear Left –
DIMMER SWITCH
7
TO IGNITION (RED)
IGNITION SWITCH
A
4
TO BATTERY(+) (YELLOW)
A
5
POWER ANTENNA/REMOTE ON (BLUE)
1
(Max. 300mA)
BATTERY
2
C
3
4
5
CONTROL RELAY
6
7
8
Attention
The connector wiring may vary depending on the car manufacturer, even when ISO connectors are used.
We recommend to check the car's wiring provision before connecting the car stereo.
Please pay particular attention to pin 5, where a misconnection might cause damage to the car or radio.
Take special care when installing into '98 or later VW/Audi/ Skoda/Seat models as there may be a 12 V connection on Pin 5, which could damage the car stereo or into Ford from '97 or later, with an ISO connector, on
which damage to the car's microcomputers is possible if misconnected.
Use of ISO connector adapters available on the market may facilitate installation.
7
A From antenna
B To the wiring of the vehicle colors of leads.
• BLACK:
This lead is for the ground connection.
• ORANGE:
This lead is for the phone line connection.
• PINK:
This lead is for the dimmer line connection.
• RED:
This lead is for connection to the power supply terminal when the ignition
switch is set to ACC.
• YELLOW:
This lead is for connection to the battery (back-up) terminal from which
power is always supplied.
• BLUE:
This lead is for the power antenna connection.
• BLUE/WHITE: This lead is for the remote amplifier on connection.
C Speaker Connections
1
2
3
4
5
6
7
8
REAR
FRONT
R
FRONT
L
R
REAR
L
Connecting to Auxiliary Equipment (Optional)
Connect the AUDIO OUTPUT jack of this unit to the AUDIO INPUT jack of the Auxiliary
Equipment.
FL (Front Left)
RL (Rear Left)
FR (Front Right)
RR (Rear Right)
To AUDIO OUT
To AUDIO IN
To AUDIO IN
Amplifier
8
Basic operation
Turning the unit on
Press MUTE/PWR (POWER
on the remote control) or any other button.
Note
When you insert the CD in the CD slot, the unit turns on.
Turning the unit off
Press and hold MUTE/PWR (POWER
on the remote control).
Selecting a source
Press SRC S repeatedly to select a source.
The indicator lights up in the following order. TUNER → CD → TUNER...
Note
You cannot select a source if a CD is not inserted.
Adjusting the volume
Rotate MUTE/PWR (Press VOLUME
on the remote control) to adjust the sound level.
Note
When you turn the unit off, the current volume level is automatically memorized. Whenever
you turn the unit back on, it will operate at the memorized volume level.
Mute
1
2
Press MUTE/PWR (POWER
To cancel it, press again.
on the remote control) to cut the sound.
Checking the clock
You can see the clock pressing DISP (DISP. on the remote control).
Note
• If the unit is receiving RDS broadcasting with CT (Clock Time) information,
the clock will be shown automatically in the display window .
• Unless, “NO CLOCK” appears in the display window.
Changing the general settings
1
2
3
4
Press and hold SEL [S] (SEL on remote control) so that one of menu items appears.
Press SEL [S] (SEL on remote control) to scroll between menus.
TA ALARM t PI SOUND t DEMO OFF t BEEP 2ND
Rotate MUTE/PWR clockwise or unclockwise to select one of the settings specified
belows.
(Press VOLUME
on the remote control.)
Press and hold SEL [S] (SEL on remote control) to finish the setting.
9
TA(Traffic Announcement) ALARM / SEEK
TA ALARM :
When a newly tuned station has no TP information for 5 seconds, a double beep sound is
output.
TA SEEK :
When the newly tuned station does not receive TP information for 5 seconds, the receiver
retunes to the next station which has the same PI as the last station, but has the TP
information.
PI (Programme Identification) SOUND / MUTE
PI SOUND :
If the sound of a station with different PI is heard intermittently, the receiver mutes the
sound after 1 second.
PI MUTE :
If the sound of a station with different PI is heard intermittently, the receiver mutes the
sound right now.
DEMO ON / OFF
You can change the initial indication on the display to information name (function name,
EQ name, etc...) while listen to a source.
DEMO ON
Displays information name while listen to source.
DEMO OFF
Cancels the function.
BEEP 2ND / ALL
Sets the beep sound every time a button is pressed.
BEEP 2ND
The beep is generated when a key is long pressed. (1 sec)
BEEP ALL
The beep is generated when any key is pressed.
RDS AF/REG FUNCTION
To switch on or off the AF function (Network-Tracking), shortly press the AF(REG) button. To
switch on or off the REG function (Regional Network Tracking), press the AF(REG) button
longer than 2 seconds.
AF(Alternative frequency) ON / OFF
When the reception quality worsens, the tuner automatically changes to another station in
the network, broadcasting a better reception quality, using the PI and AF codes.
AF ON (“AF” appears on display window) :
Wherever you drive, you can continue to listen to the same program without interruptions.
AF OFF (“AF” disappears on display window):
Only station name will be displayed. In case of poor reception no alternative station can
be used.
REG (Region) ON / OFF
REG ON :
The unit switches to another station, within the same network, broadcasting the same
program when the receiving signals from the current station become weak.
REG OFF :
The unit switches to another station, within the same network when the receiving signals
from the current station become weak. (This mode, the program may differ from the one
currently received.)
10
Using the EQ (Equalizer)
Press EQ repeatedly. The indicator lights up in the following order.
POP t CLASSIC t ROCK t JAZZ t VOCAL t SALSA t SAMBA t USER1
t USER2 t OFF
• POP
: Optimized for R&B, Soul and Country music.
• CLASSIC : Optimized for orchestral music.
• ROCK
: Optimized for Hard Rock and Heavy Metal music.
• JAZZ
: Sweet sound with soft feeling.
• VOCAL
: Powerful realism with strong sound quality.
• SALSA
: Reproduces salsa music acoustics.
• SAMBA : Reproduces samba music acoustics.
• USER1
: Use the menu to set the sound level you want.
• USER2
: Use the menu to set the sound level you want.
You can adjust each sound level to your preference. Once you select a USER mode and then
make an adjustment, it automatically stored for the currently selected USER mode.
Adjusting the sound level
1
2
Press SEL [S] (SEL on the remote control) repeatedly to select the mode you want to
adjust from volume, bass, middle, treble, balance and fader.
The indicator lights up in the following order.
VOL t BAS t MID t TRB t BAL t FAD
Rotate the MUTE/PWR (Press VOLUME
on the remote control) to adjust the sound
quality.
Indication
Turn right
Turn left
VOL
BAS
Increase the volume level.
Decrease the volume level.
Increase the bass level.
Decrease the bass level.
MID
TRB
BAL
Increase the middle level.
Decrease the middle level.
Increase the treble level.
Decrease the treble level.
Decrease the level of the
left speaker(s).
Decrease the level of the right
speaker(s).
FAD
Decrease the level of the front
speaker(s).
Decrease the level of the rear
speaker(s).
Note
When EQ and XDSS+ is set to “Off”, you can adjust the sound level (BAS, MID, TRB)
settings.
XDSS+ (Extreme Dynamic Sound System)
1
2
Press XDSS
XDSS+ : Improves the treble, bass sound.
To cancel, press XDSS again.
11
Radio operation
Listening to radio stations
1
2
3
Press SRC S to select the tuner.
Press the BAND repeatedly to select a band.
The indicator lights up in the following order. FM1 t FM2 t FM3 t MW(AM)
B[ + (?m m/M M? on the remote control).
Auto Seek : Press - [b/B
When a station is received, searching stops.
B[ + (?m m/M M? on the remote control) until
Manual Seek : Press and hold - [b/B
“MANUAL” appears, and then press it repeatedly.
The frequencies move up or down step by step.
Storing and recalling broadcast frequencies
You can easily store up to 6 broadcast frequencies for later recall at the touch of a button.
1
2
3
4
Press BAND to select desired band you want to store.
Select the desired frequency.
Press one of preset buttons 1-6 and hold until the beep sound.
The number you have pressed will flash in the preset number indicator and then remain
lit. The selected radio station frequency has been stored in memory.
Repeat steps 1-3 to preset other stations.
The next time, you press the same preset button, the radio station frequency is
recalled from the memory.
Note
• Up to 18 FM stations, 6 for each of three FM bands and 6 MW(AM) stations can be stored
in the memory.
• When a station is stored on the preset numbers on which another station of the same band
has already been preset, the previously preset station is automatically erased.
Auto search memory
This function lets you automatically store the 6 strongest broadcast frequencies.
1
2
Press AS/PS until “A/S” appears.
The six strongest broadcast frequencies will be stored under preset button 1-6 in the order
of their signal strength.
To cancel, press AS/PS.
To scan the preset stations
Press AS/PS. Each preset station appears. To cancel, press AS/PS.
To tune in the preset stations
Press BAND to select the desired band and press the desired preset button 1-6 (preset
button 1-6 on the remote control).
The preset station of the preset button 1-6 is displayed and the preset station is received.
12
RDS operation
RDS Display options
In normal RDS operation the display will indicate the station name. Pressing DISP
enables you to cycle through the various data types in the following sequence:
CT t FREQUENCY t PTY t RT t PS
• CT (Time controlled by the channel)
• PTY (Programme type recognition)
• RT (Radio text recognition)
• PS (Programme Service name)
• PI (Programme Identification)
• AF (Alternative Frequencies for the actual programme)
• TP (Traffic programme Identification)
• TA (Traffic Announcement Identification)
PTY (Programme Type) function
To select a certain program type out of the reception band, following procedure can be
operated.
1 Press BAND to select in FM mode.
2 After, pressing PTY button one by one activated as selecting each mode.
music grouptspeech grouptsearch off
3 Press one of the PRESET (1-6) button shortly. Each time this button is pressed, the
display mode changes as follow.
No
Music group
No
Speech group
1.
2.
3.
4.
5.
6.
Pop M, Rock M
Easy M, Light M.
Classics, Other M
Jazz, Country
Nation M, Oldies
Folk M
1.
2.
3.
4.
5.
6.
News, Affairs, Info
Sport, Educate, Drama
Culture, Science, Varied
Weather, Finance, Children
Social, Religion, Phone In
Travel, Leisure, Document
TA (Traffic Announcement) function
TA reception allows the unit to switch temporarily to a Traffic Announcement from the current
source (another FM station, CD, or other connected components).
To switch the TA (Traffic Announcement) function on or off, press TA.
• TA ON
Traffic programs and announcements can be automatically received using TP/TA features.
• TA OFF
Traffic programs and announcements can not be received using TP/TA features.
13
CD/MP3/WMA operation
Playing an Audio CD and MP3/WMA Disc
The unit can play MP3/WMA formatted recordings on CD-ROM, CD-R or CD-RW discs.
Before playing MP3/WMA recordings, read the notes on MP3/WMA Recordings on page 3.
If you change the source, CD play also stops (without ejecting the CD). Next time you select
“CD” as the source, CD play starts from where playback has been stopped previously.
To directly play a file, press NUMBER (#) on remote control and then press the track
number with 0-9 number.
Pause
1 Press B/X during playback.
2 To return to playback, press B/X again.
Skip to next track/file
Press briefly B[ + (M M? on the remote control) to select the next track or file.
Skip to previous track/file
Press briefly - [b (?m m on the remote control) within 3 seconds of playing time.
Return to the beginning of the current track/file
Press briefly - [b (?m m on the remote control) after 4 seconds of playing time.
Search
B[ + (?m m/M M? on remote control) for about 1 second during
Press and hold - [b/B
playback and then release at the point you want.
Intro scan
The first 10 seconds of each tracks/files (SCAN) or each files in the current selected folder
(
SCAN) on the disc are played.
1
2
Press SCAN.
–
SCAN MP3 WMA (or SCAN CD ) appears on the display window.
Press and hold SCAN for about 2 seconds during playback.
– SCAN appears on the display window. MP3 WMA
Press SCAN again.
– SCAN or
SCAN disappear from the display window and the intro scan is cancelled.
Repeat
The current selected tracks/files (1 RPT) or folder (
1
2
3
RPT) on the disc is played repeatedly.
Press RPT during playback.
– 1 RPT appears on the display window. CD MP3 WMA
Press and hold RPT for about 2 seconds during playback.
–
RPT appears on the display window. MP3 WMA
Press RPT again.
– 1 RPT or
RPT disappear from the display window and the repeat mode is cancelled.
14
Shuffle
All of the tracks/files (SHF) or the current selected folder (
SHF) on the disc is played
randomly.
1 Press SHF during playback.
–
SHF MP3 WMA (or SHF CD ) appears on the display window.
Press and hold SHF for about 2 seconds during playback.
– SHF appears on the display window. MP3 WMA
2 Press SHF again.
– SHF or
SHF disappear from the display window and the random playback is
cancelled.
Note
During random playback, if you press - [b (?m m on remote control), you won’t go back to
the previous track.
CD TEXT / ID3 TAG
When playing a disc containing information, you can see the CD TEXT/ID3 TAG information.
In CD TEXT, information about the disc (disc title, performer and track title) is recorded.
In a ID3 TAG, information about the file (Alburm title/ Song title/ Performer name) is recorded.
In a WMA Content, information about the file (Song title/ Performer name) is recorded.
If there is no information, “NO TEXT” will be shown in the display window.
Press DISP (DISP. on the remote control) repeatedly during MP3/WMA/CD TEXT file playback.
To go to a particular quickly (+10/-10 steps)
MP3
WMA
(If there is no folder or one folder.)
Press F+ to skip to the next 10 track, and press F- to skip to the previous 10 track.
To skip to the next or previous folder
MP3
WMA
(If there are more than two folders.)
Press F+ to skip to the next folder, and press F- to skip to the previous folder.
Note
Time display appearing on the display part when playing VBR file may vary and there may be
some difference from actual time (both progress time and VBR are displayed at the same
time when playing file).
15
Troubleshooting
Sy
Co
: Symptom /
: Correction
Ca
: Cause
Ca The loaded disc is of a type this unit
cannot play.
Co Check what type the disc.
Sy Power doesn’t turn on. / The unit
doesn’t operate.
Ca Leads and connectors are not properly
connected.
Co Confirm once more that all
connections are correct.
Ca The fuse is blown.
Co Rectify the problem that caused the
fuse to blow, and then replace it. Be very
sure to install the correct fuse with the same
rate.
Ca Noise and other factors are causing
the built-in microprocessor to operate
incorrectly.
Co Turn the unit off and then on.
Sy
Ca
Co
Sy No sound is heard. / The volume
level will not rise.
Ca Cables are not connected correctly.
Co Connect the cables correctly.
Sy
Ca
Co
There’s no sound.
The volume level is low.
Adjust the volume.
Sy
Ca
Co
There’s audio skipping.
This unit is not firmly secured.
Secure this unit firmly.
Sy The unit does not operate correctly
even when the appropriate remote
control buttons are pressed.
Ca Battery power is low.
Co Load new battery.
Playback is not possible.
The disc is dirty.
Clean disc.
Specifications
GENERAL
Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50W x 4CH (Max.)
Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DC 12V
Speaker impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Ω
Ground System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative
Dimensions (W x H x D) . . . . . . . . . . . . . . . . . . . . . .181.5 x 50 x 200 mm (Without Control Panel)
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5 kg
CD SECTION
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hz-20 kHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.12%
Channel Separation (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 dB
RADIO SECTION
FM
Frequency Range . . . . . . . . . . . . . . . . . . . . . .87.5-107.9, 87.5-108, 65-74 or 87.5-108 MHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.7%
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 dBµV
AM (MW)
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .520-1720 or 522-1620 kHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0%
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 dBµV
Designs and specifications are subject to change without notice.
16
Download PDF