LG | LPT-OS553HQ | Owner's Manual | LG LPT-OS553HQ Owner’s Manual

LG LPT-OS553HQ Owner’s Manual
LPT-OS553HQ_ENG_6602
7/19/07
2:08
PM
Page
1
Dome Camera
Owner's Manual
MODEL: LPT-OS551HQ
LPT-OS553HQ
Before
manual
installing and using the camera, please read
carefully and retain for future reference.
this owner's
LPT-OS553HQ_ENG_6602
7/19/07
2:08
PM
2
Page
?
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
(OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
space such
lightning flash with arrowhead symbol
an equilateral triangle is intended to
within
alert the
ed
user
to the presence of uninsulat-
within the
dangerous voltage
product's
sufficient magni-
enclosure that may be of
tude to constitute a risk of electric shock to
persons.
point
within
an
is intended to alert the
equilateral
user
to the
presence of
important operating and main(servicing) instructions in the literaaccompanying the product.
equipment
has been tested and found to
with the limits for
a
Class A
to
provide
com-
digital device,
reasonable
harmful interference when the
a
protection against
equipment is operat-
commercial environment.
This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction
cause
manual, may
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his
?
own expense.
A suitable conduit
shall be
provided
uct in the end
2
in which
adequate
Warning:
Code, ANSI/NFPA
class A
product
the
case
product.
In
user
70.
domestic
radio interfer-
cause
may
a
may be
required
to take
measures.
To reduce
a
risk of fire
product
to rain
or
or
electric
shock, do
moisture.
Caution: This installation should be made
by
a
quali-
fied service person and should conform to all local
codes.
with
or
in the cable entries of
user.
glands
this prod-
to
qualified personnel only.
liquids,
such
vases, should be
as
placed
on
the
apparatus.
Disposal
of your old
appliance
1. When this crossed-out wheeled bin
symbol is
product it means the product is
by the European Directive
attached to
a
2002/96/EC.
2. All electrical and electronic
products should be
separately from the municipal
waste stream via designated collection facilities appointed by the government or the local
disposed
of
authorities.
3. The correct
disposal of your old appliance will
help prevent potential negative consequences
for the environment and human health.
4. For
more
detailed information about
disposal
city
of your old appliance, please contact your
office, waste disposal service or the shop
where you
This
entries, knock-outs
servicing
Caution: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
covered
pursuant to Part 15 of the FCC Rules. These limits are
ed in
ence
a
ture
REGULATORY INFORMATION: FCC Part 15
designed
This is
environment this
similar unit.
Caution: To avoid electrical shock, do not open the
: This equipment may generate or
frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly
approved in the instruction manual. The user could
lose the authority to operate this equipment if an
unauthorized change or modification is made.
ply
with the National Electric
Warning:
or
methods shall be in accordance
cabinet. Refer
radio
This
bookcase
tenance
FCC WARNING
use
as a
Warning: Wiring
not expose this
The exclamation
triangle
Holes in metal,,through which insulated wires
pass,shall have smooth well rounded surfaces or
shall be provided with brushings.
Warning: Do not install this equipment in a confined
?
OF ELECTRIC SHOCK
This
Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer 's instructions.
CAUTION: TO REDUCE THE RISK
DO NOT REMOVE COVER
Caution:
purchased
product
the
product.
is manufactured to
with the EEC DIRECTIVE
comply
89/336/EEC,
93/68/EEC and 2006/95/EC.
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Page
3
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER'S MANUAL. AND
THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This
designed and manufactured to assure personal safety. Improper use can result in electric shock or
safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
product
has been
fire hazard. The
DO NOT REMOVE THE CABINET
COVER,
OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL ONLY.
1.
Read these instructions.
-
All these
safety and operating
product is operat-
10.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11.
Only
instructions should be read before the
ed.
2.
Keep these instructions.
-
The
safety, operating
and
use
instructions should be retained for future reference.
3.
Heed all
the
4.
warnings. All warnings on the product
operating instructions should be adhered to.
-
Follow all instructions.
-
All
operating
and
use
and in
12.
Do not
Use
only with the cart, stand, tripod, bracket, or
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
instruc-
For example:
this apparatus near water.
tub, wash bowl, kitchen sink, laundry tub, in a
basement; or near a swimming pool; and other areas
located
6. Clean
use
-
near
water.
only with dry cloth.
cleaning.
wall outlet before
7.
specified by the
bath
near a
wet
attachments/accessories
table
tions should be followed.
5.
use
manufacturer.
-
Unplug
Do not
this
use
product from the
liquid cleaners.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Slots and
-
provided for ventilation and to
ensure reliable operation of the product and to protect it
from over-heating. The openings should never be blocked
by placing the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a built-in
openings
in the cabinet
installation such
tilation is
as a
provided
or
are
bookcase or rack unless proper venthe manufacturer's instructions have
been adhered to.
8.
Do not install
near
any heat
sources
tors, heat registers, stoves,
or
such
other
as
radia-
apparatus
(including amplifiers) that produce heat.
9.
13.
Unplug this apparatus during lightning
long periods of time.
storms
or
when unused for
14.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
3
LPT-OS553HQ_ENG_6602
7/19/07
2:08
PM
4
Page
Introduction
Contents
About Dome Camera
Introduction............................4-7
IMPORTANT SAFETY INSTRUCTIONS
.
.
.
.
.
.
.
.3
Contents................................4
AboutDomeCamera....................4
The dome
cameras are
camera incorporates the digital signal processor,
pan/tilt mechanism, x27 zoom lens and RS-485 com-
Features............................4-5
munication interface in
A
IdentificationofCamera..................7
suitable for
RemovingtheProtectionTape................8
MountingtheCamera.....................8-9
Setup
as
use
well
menus
lance tasks
recording
in
extremely
daylight.
allow the
and
compact outdoor enclosure.
under
as
by
a
1/4" CCD makes the
newly developed
ditions
Precautions..............................8
an
system.
The
SafetyPrecautions......................6
Installation............................8-13
for installation in
designed
indoor/outdoor video surveillance
such
con-
to perform surveildigital flip, pattern-
camera
means as
privacy
camera
low illumination
zones.
?Surfacemount.........................8
?Pendantmount........................9
?Wallmount...........................9
SettingtheSwitch......................10-13
?RS-485ParameterSetup................10
?CameraIDSetting..................11-13
Connections.........................14-17
Features
x
x
position is the function to register camera
monitoring positions (preset positions) associated
with position numbers. By entering the position
RS-485Connection.......................14
ALARMINConnections....................15
numbers, you
AlarmInputfunction.......................16
SystemConnection.......................17
AdapterConnections......................17
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Reference..............................31
Specifications...........................31
4
can move cameras
to the
preset
positions.
A maximum of 128 Preset Position is available.
The
moving speed
adjustable.
SetupMenu..........................18-30
.
Preset Position
Preset
Precautions.............................14
.
with
1/4" EX-view CCD.
ConnectionPreview.......................14
SetupMenuOverview.....................18
SettingCameraMenu.....................19
CameraIdentificationSetting................20
FocusSettings........................20-21
.22
WhiteBalanceControlSettings
ExposureSettings.....................23-25
AutoExposureLevelSettings...............26
SpecialSettings.......................27-28
MotionDetectionSetting...................29
Function On-Screen Display Setting
.29
PrivacyMaskingSettings...................30
High Sensitivity Support
camera provides the high quality picture
The
x
holding
time
are
Preset Tour
You
can
been
x
and
Preset
You
tour all
preset positions that has already
registered.
Group
Tour
a preset group using the preset
positions that has already been registered (maximum 9 groups) and you can tour the preset posican
create
tion within the group.
A preset group should have
set
positions.
a
maximum of 8 pre-
7/19/07
LPT-OS553HQ_ENG_6602
x
2:08
PM
Page
5
Pattern Function
x
A routine of manual
operations can be stored for 5
minutes at the maximum and reproduced repetitively. The Panning, Tilting and Zoom controls are
available for recording the pattern.
Note: The available total time of pattern differs
depending on camera's operation. When the time
is over, the
x
x
Alarm
the
x
has
x
specific
every detail occurarea, which is preset to
x
on
x
are
Auto
adjustable.
flip
function allows the tilt
x
Night
or
an
department
excellent
stores.
can
be selected Color
set Color in the
or
Black &
daytime
and Black
to the low illumination.
(Filter
DSS
(Digital Slow Shutter) function
possible to highly sensitive surveillance
because of DSS(Digital Slow Shutter) function.
This is the surveillance
WDR
(Wide Dynamic Range)
camera can
inside
Sophisticated Design
pact
camera can
The
approx. 90°.
x
Day
This
connected
It is
angle to widen
image on the monitor screen is
flipped horizontally and vertically at the tilt angle of
indoor
being
Function
night due
Conversion type)
x
up to 180°. The
x
cameras
cameras.
large buildings
&
& White at
Flip
The Auto
in the
White. You
pan among the maximum 8
you will set. The moving speed and holding
points
be utilized after
Therefore, it is capable of performing
camera can
time
camera can
with maximum 256
watch in advance.
The
General Controller
camera can
Connects with the maximum 256
This
Auto Pan function that
surveillance
keep
around the
an
by
be controlled by RS-485.
Especially the camera has an excellent cost-saving effect because it can be controlled by the general RX point of contact signal.
job
camera
enables to
ring
Controls
This
Auto Pan
The
input signals are supplied from external
through the ALARM IN connector to turn
camera to a preset position.
devices
pattern setup will automatically stop.
Privacy Mask
Privacy zone feature enables users to veil unwanted zones. This setting is used for masking
unwanted zones, hiding them from display on the
monitor screen. Up to 8 zones can be registered.
Alarm In function
or
function
be best condition to watch
outside in the
easily
strong back light.
During Auto Pan, Preset Tour, or Pattern
Record/Play, you can use only STOP key or
Joystick on the controller.
Note:
camera
that
fit any
in the com-
can
surroundings because it comes
sophisticated design.
size and
x
Power
Supply
Zoom Lens & Auto Focus
This
Zooming is possible from 27 times (the optical
zoom limit), to a maximum of X2 times digital
Certified/Listed, class
camera
must
always
be
operated a DC
supply only.
12V
2 power
zoom.
x
Sensor
Linkage
is capable of capturing a subject by
the focus of camera moving promptly toward the
subject at the rate of 120°/sec when the camera
works with a detector (magnetic, beam, infrared
rays), and a subject moving within a detection
area is captured by a detector.
The
camera
5
7/19/07
LPT-OS553HQ_ENG_6602
PM
Page
6
Precautions
Safety
x
2:08
x
attempt to disassemble the camera
prevent electric shock,do not remove screws or
covers. There are no user serviceable parts inside.
x
a
qualified
Avoid the
camera
Do not aim the
the
camera
direct
service
is in
personnel
for
use or
at
servicing.
-
never
-
sunlight or other extremely bright objects.
blooming or smear may be caused.
-
camera
with
care
camera
handling
x
Do not
Use
a
use
dry
is hard to
mild
x
or
could be
striking, shaking,
damaged by improper
remove
camera
the dirt
and
Do not install this
wipe
it
on
or
detergents
dirty.
when it is
Use in
eyeglasses
Use in
the camera,
x
an
environment where
an
frequent
foggy.
a room
filled with
cigarette
cloudy
smoke
or
due to
Before
a
use a
Use the
gently.
cover
and
operating, please
check proper
source
all
ture is between -10 °C
--
+50 °C and
temper-
ratings.
under conditions where
camera
wipe
soft cloth.
ature, humidity and power
tempera-
humidity
is
below 80%.
camera
The
x
input
power
source
is DC 12V.
Consumables
Parts
having
contacts such
as
the lens-drive
motors, cooling fan built inside the
subject
to
wear
with time. About
maintenance of such
service center.
6
by switching
due to
If the lens becomes
If it
upside down
This camera is designed for mounting on the ceiling or wall.If you install this camera upside down,
for example, mounted on the floor, it may cause
malfunction.
fluctuation
Rapid temperature fluctuation
opening and closing.
moist surfaces with
strong solvents
detergent
as
and off.
on
condensation,remove the dome
storage.
cloth to the
places
dust.
Do not abuse the camera.Avoid
etc. The
Rapid temperature
become
-
Handle the
in such
door
face it with
Otherwise
x
camera
air conditioner
sunlight
bright objects.Whether
not,
the
tions.
with direct
camera
use
The lens may become cloudy due to condensation
if the camera is used under the following condi-
Do not
To
Ask
Do not
shown below.
camera are
replacement and
parts, please ask the nearest
LPT-OS553HQ_ENG_6602
7/19/07
2:08
PM
Page
7
Identification of Camera
4
5
1
6
7
"A"
2
8
3
1
Camera
2
Dome
camera
3
Dome
cover
4
Power cable
5
Video
mounting
bracket
body
(DC 12V)
output cable with BNC
connector
Connects with the video connector of the monitor.
6
Data Communication Port
(RJ45)
7
Data Communication Port
(RJ45)
8
Fall Prevention Wire
Be
sure
"A"
to hook the fall
prevention
-
-
RS-485 and Alarm
Input
RS-485 and Alarm
Input
wire into
an
bracket.
Do not expose cable connection part to outdoor such as
waterproof problem. But If you are indeed. Sealing them
rain, moisture environment. It may
cause
tightly.
7
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Page
8
Installation
Surface mount
Precautions
?
The
following steps
of installation and connection
work should be done
nel
or
by qualified
service personto all
The
system installers and should conform
The
Ceiling
local codes.
?
Be
sure
to switch the
camera
off before installation
and connection.
?
Do not install the
camera near
the air outlet of
an
air conditioner.
?
Do not touch the dome cover's window.
the Protection
Removing
Before
using
the camera,
Caution: Remove the
1.
Loosen the
the dome
Tape
remove the protection tape.
protection tape carefully.
using
screws
cover as
the wrench and
remove
shown below.
Protection
tape.
Remove the
2.
protection tape
and attach the dome
Note:
cover.
When you install the
camera to the ceiling
mount, you must drill
a
hole in the
body as
(ø5.0)
Mounting
The
on a
figures
ceiling
the Camera
show
or
an
example of the camera mounted
a locally procured bracket.
wall with
Refer to the instructions included with the bracket for
filling
8
gaps and holes with
waterproof
material.
camera
shown
right.
Ceiling
LPT-OS553HQ_ENG_6602
Pendant mount
7/19/07
2:08
PM
Page
9
Wall mount
(Optional)
(Optional)
How to install
"A"
Pipe
threads should be clean and
rust free. Use
a
TeflonTM
or
tape
sealer
(such as
sealer)
silicone
on
the threads.
Add thread
sealing
tape
Reference:
Specifications
of LG Standard
pipe.
Note:
Do not
block
remove
the
(A)
keep the
(B) between the
camera body and
to
gap
(B)
(A)
installation bracket.
9
7/19/07
LPT-OS553HQ_ENG_6602
The DIP switch of the
use.
PM
Page
10
the Switch
Setting
and
2:08
camera
Switch
Function Effect
position (SW101)
When the
is two 4-bit switches
employs RS-485 communication
Switch settings are read into the
mode
basic
as
camera
when
ON
1234
with LG
(ON
ON ON
ON)
the power is turned on. Make sure to turn it off, then
turn it back after changing the switch settings.
protocol.
protocol
allow
protocol,communication parameters,
and set unit numbers
power is switched
are
read into the
camera
1234
Turn off the
2.
Remove the dome
OFF ON
ON)
when
OFFONONON
from the
is
1234
camera as
shown below.
ON
OFF OFF ON ON
1234
1
protocol.
The controller with LG
Multix
ON
camera.
cover
camera
with LG Multix
(ON
on.
1.
camera.
connected to the controller
ON
The selected
limited
only
control for this
Setup
The
controller with LG
When the
RS-485 Parameter
is
camera
connected to the controller
protocol
allow all
control for this
camera.
Reserved 1
(Pelco
D
protocol)
Reserved 2
(Pelco
P
protocol)
ON
ONONOFFON
Reserved 3
OFF ON OFF ON
Reserved 4
ON OFF OFF ON
Reserved 5
OFF OFF OFF ON
Reserved 6
ONONONOFF
Reserved 7
OFF ON ON OFF
Reserved 8
ON OFF ON OFF
Reserved 9
OFF OFF ON OFF
Reserved 10
ON ON OFF OFF
Reserved 11
OFF ON OFF OFF
Reserved 12
ON OFF OFF OFF
Reserved 13
OFF OFF OFF OFF
Reserved 14
1234
ON
1234
2
ON
1234
ON
1234
ON
3.
Set the DIP switch
camera
according
on
the bottom
part of the
1234
to the function shown in the
table of the below.
ON
1234
ON
1234
SW101
ON
1234
ON
ON
ON
1234
OFF
ON
1234
1234
ON
1234
SW104
ON
1234
ON
ON
OFF
1234
Note: If you are not using the controller with LG
there may be some limitation of function
protocol,
control.
10
7/19/07
LPT-OS553HQ_ENG_6602
Switch
2:08
position (SW104)
PM
Page
11
ID
BAUD RATE
The table for the
camera
9,600 BPS
ID
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
setting
ON
(OFF
1234
OFF OFF
OFF)
1ONOFFOFFOFFOFFOFFOFFOFF
ON
(OFF
1234
OFF OFF
1,200 BPS
ON)
2OFFONOFFOFFOFFOFFOFFOFF
3ONONOFFOFFOFFOFFOFFOFF
ON
1234
(OFF
OFF ON
OFF)
2,400 BPS
(OFF
OFF ON
ON)
4,800 BPS
4OFFOFFONOFFOFFOFFOFFOFF
5ONOFFONOFFOFFOFFOFFOFF
6OFFONONOFFOFFOFFOFFOFF
ON
1234
7ONONONOFFOFFOFFOFFOFF
8OFFOFFOFFONOFFOFFOFFOFF
9ONOFFOFFONOFFOFFOFFOFF
ON
1234
(OFF
ON OFF
OFF)
19,200 BPS
(OFF
ON OFF
ON)
38,400 BPS
(OFF
ON ON
OFF)
57,600 BPS
(OFF
ON ON
ON)
115,200 BPS
10OFFONOFFONOFFOFFOFFOFF
11ONONOFFONOFFOFFOFFOFF
ON
1234
12OFFOFFONONOFFOFFOFFOFF
13ONOFFONONOFFOFFOFFOFF
14OFFONONONOFFOFFOFFOFF
ON
1234
15ONONONONOFFOFFOFFOFF
16
ON
1234
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
17ONOFFOFFOFFONOFFOFFOFF
18OFFONOFFOFFONOFFOFFOFF
19ONONOFFOFFONOFFOFFOFF
4.
Turn
on
the
camera.
Setup
is
completed.
20OFFOFFONOFFON
OFFOFFOFF
21ONOFFONOFFONOFFOFFOFF
22OFFONONOFFONOFFOFFOFF
23ONONONOFFONOFFOFFOFF
Camera ID
This
camera
24OFFOFFOFFONON
Setting
has the
camera
ID set to "1" at the time
of the
shipment. If you use 2 cameras or more simultaneously, change the ID to "2" using the 8-bit DIP
switch of the 2
Set the
camera
camera
and the table
on
ID
with
a
OFFOFFOFF
25ONOFFOFFONONOFFOFFOFF
screwdriver.
setting referring
to the
26OFFONOFFONONOFFOFFOFF
27ONONOFFONONOFFOFFOFF
28OFFOFFONONON
OFFOFFOFF
29ONOFFONONONOFFOFFOFF
30OFFONONONONOFFOFFOFF
pictures
the below.
31ONONONONONOFFOFFOFF
32
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
33ONOFFOFFOFFOFFONOFFOFF
?
The default
setting
of the
camera
ID is 1.
34OFFONOFFOFFOFFONOFFOFF
35ONONOFFOFFOFFONOFFOFF
36OFFOFFONOFFOFFONOFFOFF
37ONOFFONOFFOFFONOFFOFF
38OFFONONOFFOFFONOFFOFF
39ONONONOFFOFFONOFFOFF
40OFFOFFOFFONOFFONOFFOFF
41ONOFFOFFONOFFONOFFOFF
42OFFONOFFONOFFONOFFOFF
43ONONOFFONOFFONOFFOFF
44OFFOFFONONOFFONOFFOFF
45ONOFFONONOFFONOFFOFF
46OFFONONONOFFONOFFOFF
47ONONONONOFFONOFFOFF
ON
12345678
SW102
48OFFOFFOFFOFFON
ONOFFOFF
49ONOFFOFFOFFON
ONOFFOFF
50OFFONOFFOFFON
ONOFFOFF
51ONONOFFOFFON
ONOFFOFF
52OFFOFFONOFFON
ONOFFOFF
11
LPT-OS553HQ_ENG_6602
ID
SW1
7/19/07
SW2
SW3
2:08
SW4
PM
SW5
Page
SW6
12
SW7
SW8
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
106OFFONOFFONOFFON
54OFFONONOFFONONOFFOFF
107ONONOFFONOFFONONOFF
55ONONONOFFONONOFFOFF
108OFFOFFONONOFFON
56OFFOFFOFFONON
ONOFFOFF
109ONOFFONONOFFONONOFF
57ONOFFOFFONON
ONOFF
ONOFF
ONOFFOFF
110OFFONONONOFFONONOFF
58OFFONOFFONONONOFFOFF
111ONONONONOFFONONOFF
59ONONOFFONONONOFFOFF
112OFFOFFOFFOFFON
ON
ONOFF
60OFFOFFONONON
ONOFFOFF
113ONOFFOFFOFFON
ON
ONOFF
61ONOFFONONONONOFFOFF
114OFFONOFFOFFON
ON
ONOFF
62OFFONONONONONOFFOFF
115ONONOFFOFFON
ON
ONOFF
63ONONONONONONOFFOFF
116OFFOFFONOFFON
ON
ONOFF
64
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
117ONOFFONOFFONONONOFF
65ONOFFOFFOFFOFFOFFONOFF
118OFFONONOFFON
66OFFONOFFOFFOFFOFFONOFF
119ONONONOFFONONONOFF
67ONONOFFOFFOFFOFFONOFF
120OFFOFFOFFONON
ON
68OFFOFFONOFFOFFOFFONOFF
121ONOFFOFFONON
ONONOFF
69ONOFFONOFFOFFOFFONOFF
122OFFONOFFONON
ON
70OFFONONOFFOFFOFFONOFF
123ONONOFFONONONONOFF
71ONONONOFFOFFOFFONOFF
124OFFOFFONONON
72OFFOFFOFFONOFFOFFONOFF
125ONOFFONONONONONOFF
73ONOFFOFFONOFFOFFONOFF
126OFFONONONONONONOFF
74OFFONOFFONOFFOFFONOFF
127ONONONONONONONOFF
75ONONOFFONOFFOFFONOFF
128
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
76OFFOFFONONOFFOFFONOFF
129
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
77ONOFFONONOFFOFFONOFF
130
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
78OFFONONONOFFOFFONOFF
131ONONOFFOFFOFFOFFOFFON
79ONONONONOFFOFFONOFF
132
80OFFOFFOFFOFFONOFFONOFF
133ONOFFONOFFOFFOFFOFFON
81ONOFFOFFOFFONOFFONOFF
134OFFONONOFFOFFOFFOFFON
82OFFONOFFOFFONOFFONOFF
135ONONONOFFOFFOFFOFFON
83ONONOFFOFFONOFFONOFF
136
84OFFOFFONOFFONOFFONOFF
137ONOFFOFFONOFFOFFOFFON
85ONOFFONOFFONOFFONOFF
138OFFONOFFONOFFOFFOFFON
86OFFONONOFFONOFFONOFF
139ONONOFFONOFFOFFOFFON
87ONONONOFFONOFFONOFF
140OFFOFFONONOFFOFFOFFON
88OFFOFFOFFONONOFFONOFF
141ONOFFONONOFFOFFOFFON
89ONOFFOFFONONOFFONOFF
142OFFONONONOFFOFFOFFON
90OFFONOFFONONOFFONOFF
143ONONONONOFFOFFOFFON
91ONONOFFONONOFFONOFF
144
92OFFOFFONONONOFFONOFF
145ONOFFOFFOFFONOFFOFFON
93ONOFFONONONOFFONOFF
146OFFONOFFOFFON
94OFFONONONONOFFONOFF
147ONONOFFOFFONOFFOFFON
95ONONONONONOFFONOFF
148OFFOFFONOFFON
96OFFOFFOFFOFFOFFON
ONOFF
149ONOFFONOFFONOFFOFFON
97ONOFFOFFOFFOFFON
ONOFF
150OFFONONOFFON
98OFFONOFFOFFOFFON
ONOFF
151ONONONOFFONOFFOFFON
99ONONOFFOFFOFFON
ONOFF
152OFFOFFOFFONON
100OFFOFFONOFFOFFON
ONOFF
153ONOFFOFFONONOFFOFFON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
ONONOFF
ON
OFF
OFF
OFF
ONOFF
ONOFF
ONOFF
OFF
OFF
OFF
ON
ON
ON
OFFOFFON
OFFOFFON
OFFOFFON
OFFOFFON
101ONOFFONOFFOFFONONOFF
154OFFONOFFONON
102OFFONONOFFOFFON
155ONONOFFONONOFFOFFON
ONOFF
OFFOFFON
103ONONONOFFOFFONONOFF
156OFFOFFONONON
104OFFOFFOFFONOFFON
157ONOFFONONONOFFOFFON
ONOFF
105ONOFFOFFONOFFONONOFF
12
ID
53ONOFFONOFFONONOFFOFF
158OFFONONONON
OFFOFFON
OFFOFFON
LPT-OS553HQ_ENG_6602
ID
SW1
SW2
SW3
7/19/07
SW4
SW5
2:08
SW6
PM
Page
SW7
13
SW8
159ONONONONONOFFOFFON
160
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ID
SW1
SW2
SW3
SW4
SW5
212OFFOFFONOFFON
SW6
SW7
SW8
OFFONON
213ONOFFONOFFONOFFONON
161ONOFFOFFOFFOFFONOFFON
214OFFONONOFFON
162OFFONOFFOFFOFFONOFFON
215ONONONOFFONOFFONON
OFFONON
163ONONOFFOFFOFFONOFFON
216OFFOFFOFFONON
164OFFOFFONOFFOFFONOFFON
217ONOFFOFFONONOFFONON
165ONOFFONOFFOFFONOFFON
218OFFONOFFONON
166OFFONONOFFOFFONOFFON
219ONONOFFONONOFFONON
167ONONONOFFOFFONOFFON
220OFFOFFONONON
168OFFOFFOFFONOFFONOFFON
221ONOFFONONONOFFONON
169ONOFFOFFONOFFONOFFON
222OFFONONONONOFFONON
170OFFONOFFONOFFONOFFON
223ONONONONONOFFONON
171ONONOFFONOFFONOFFON
224OFFOFFOFFOFFOFFON
ONON
172OFFOFFONONOFFONOFFON
225ONOFFOFFOFFOFFON
ONON
173ONOFFONONOFFONOFFON
226OFFONOFFOFFOFFON
ONON
174OFFONONONOFFONOFFON
227ONONOFFOFFOFFON
ONON
175ONONONONOFFONOFFON
228OFFOFFONOFFOFFON
ONON
176OFFOFFOFFOFFON
ONOFFON
229ONOFFONOFFOFFONONON
177ONOFFOFFOFFON
ONOFFON
230OFFONONOFFOFFON
178OFFONOFFOFFON
ONOFFON
231ONONONOFFOFFONONON
179ONONOFFOFFON
ONOFFON
232OFFOFFOFFONOFFON
180OFFOFFONOFFON
ONOFFON
233ONOFFOFFONOFFONONON
OFFONON
OFFONON
OFFONON
ONON
ONON
181ONOFFONOFFONONOFFON
234OFFONOFFONOFFON
182OFFONONOFFON
235ONONOFFONOFFONONON
ONOFFON
ONON
183ONONONOFFONONOFFON
236OFFOFFONONOFFON
184OFFOFFOFFONON
ONOFFON
237ONOFFONONOFFONONON
ONON
185ONOFFOFFONON
ONOFFON
238OFFONONONOFFONONON
186OFFONOFFONON
ONOFFON
239ONONONONOFFONONON
187ONONOFFONONONOFFON
240OFFOFFOFFOFFON
ON
ONON
188OFFOFFONONON
ONOFFON
241ONOFFOFFOFFON
ON
ONON
189ONOFFONONONONOFFON
242OFFONOFFOFFON
ON
ONON
190OFFONONONONONOFFON
243ONONOFFOFFONONONON
191ONONONONONONOFFON
244OFFOFFONOFFON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ONON
ON
245ONOFFONOFFONONONON
193ONOFFOFFOFFOFFOFFONON
246OFFONONOFFONONONON
194OFFONOFFOFFOFFOFFONON
247ONONONOFFONONONON
195ONONOFFOFFOFFOFFONON
248OFFOFFOFFONON
196OFFOFFONOFFOFFOFFONON
249ONOFFOFFONONONONON
197ONOFFONOFFOFFOFFONON
250OFFONOFFONONONONON
198OFFONONOFFOFFOFFONON
251ONONOFFONONONONON
199ONONONOFFOFFOFFONON
252OFFOFFONONON
200OFFOFFOFFONOFFOFFONON
253ONOFFONONONONONON
201ONOFFOFFONOFFOFFONON
254OFFONONONONONONON
202OFFONOFFONOFFOFFONON
255ONONONONONONONON
192
ON
ON
ONON
ONON
203ONONOFFONOFFOFFONON
204OFFOFFONONOFFOFFONON
205ONOFFONONOFFOFFONON
206OFFONONONOFFOFFONON
207ONONONONOFFOFFONON
208OFFOFFOFFOFFONOFFONON
209ONOFFOFFOFFONOFFONON
210OFFONOFFOFFONOFFONON
211ONONOFFOFFONOFFONON
13
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Page
14
Connections
Connection Preview
DC 12V
Video
The connections should be made
service
personnel
or
by qualified
system installers in
accor-
dance with all local codes.
?
DC 12V
can
Note: When
plug
data
port
Ethernet cable
data
port
Ethernet cable
be used.
up, the unit
Use the cable that is described below for RS-485 site
communication.
?
powered
performs
self-check (including one panning, tilting, zooming
and focusing operation).
14
BNC
RS-485 Connection
Precautions
?
output
DC 12V cable for Camera
a
Shielded, twisted pair cable
?
Low
?
Wire gauge size is thicker than AWG #22
impedance
(0.33
mm
2
).
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Page
15
ALARM IN Connections
?
Auto mode:
sor
An
harness
8-pin
are
supplied
with the
camera as
standard accessories. Connect external
sensors
to
that
Change
senses a
position
that
the observe
touch
previously
Duration Time of Alarm
or
position
to
a sen-
shock then return to the
observed.
Input
.
(Set
the
function to "1 to
255".)
this connector.
Input specifications are low-active,
non-voltage contact (ON when active) or open
collector (Low when active).
<Example
:
If this unit receives
signal
from "Alarm 3">
Cautions
?
Alarm
one
?
input
port of
connection must be connected to
two communication
Do not connect
one
camera's alarm
What is Alarm
This
speed
sense
Input
dome
the alarm
If the alarm
camera
camera
has
a
etc.
are
Alarm
Input
terminal that
can
that has installed in
sense a
touch
signal
or
to the
will observe the sensed
There
to the several
function?
send the alarm
sensor
sensor
connector.
signals.
sensor
window, safe
alarm
input
only
ports.
a door,
shock, the alarm
camera
and the
position.
"Manual mode" and "Auto mode" for the
function.
Note
:
The Alam In 1 is Preset 1, Alam In 2 is Preset
2,AlamIn3isPreset3andAlamIn4is
Preset 4.
?
Manual mode:
the observe
position to a
sensor that senses a touch or shock then keep
observe the sensed position. (Set the Duration Time
of Alarm Input function to "0".)
<Example
:
Change
If this unit receives
signal
from "Alarm 3">
15
LPT-OS553HQ_ENG_6602
Alarm
Input
Listed below
7/19/07
2:08
PM
Page
function
the
are
camera
actions of alarm
While observe
a
specific
operating
function.
16
the observe
Auto mode
position to the
position then return to the
position that previously observed.
Change
the observe
alarmed
Stop preset touring and change the
observe position to the alarmed position then keep observe the alarmed
position.
Stop preset touring and change the
observe position to the alarmed
position then restart the preset touring
again.
Auto
Stop
Pan function.
While
different function status in each mode
Preset
Tour function.
operating
by
position to the
position then keep observe
alarmed position.
Change
the
While
function
alarmed
position.
operating
input
Manual mode
Function status
While
16
Pattern
panning and change the
position to the alarmed
position then keep observe the
alarmed position.
Stop
observe
observe
Stop operating pattern function and
change the observe position to the
alarmed position then keep observe
the alarmed position.
Stop operating pattern function and
change the observe position to the
alarmed position then restart the pattern function again.
auto
panning and change the
position to the alarmed
position then restart the auto panning
again.
auto
LPT-OS553HQ_ENG_6602
System
7/19/07
2:08
PM
Page
17
Connection
Note: When any peripheral is turned off and turned
and turned back on.
on
again,
the
camera
is also turned off
Caution: Connect the
termination
adapter
camera's data
Alarm In #2
port
supplied
to the final
to
prevent the
RS-485 communication
RS-485 Connection
(TRX D+,
TRX
error.
RS-485 Connection
Alarm In #1
D-)
TRX
(TRX D+,
D-)
Adapter
(Supplied)
Alarm In #3
Alarm In #4
Controller
DVR
Caution: Do not connect the alarm connectors to the another camera's alarm connectors.
Adapter Connections
The
adapter
is used to connect to another camera, alarm sensor,
or
controller with RS-485
Brown
1
ALARMIN1
Blue
2
ALARMIN2
Yellow
3
GND
Green
4
TRXD-
TXD
Red
5
TRXD+
TXD
Black
6
GND
Orange
7
ALARMIN3
White
8
ALARMIN4
protocol,
To Alarm
etc.
sensor
---
RS-485 Connection
+
To Alarm
sensor
17
7/19/07
LPT-OS553HQ_ENG_6602
Setup
Setup
2:08
PM
Page
18
Menu
Menu Overview
Setup menus are shown in the table below. You can adapt the camera to your requirements by setting up the
respective items in these menus. These menus are described on the following pages for reference. Switches
and keys on the controller are used in the setup operations.
Main Menu
Sub Menu
CAMERA ID
FOCUS SET
AWB SET
AE MODE
AE LEVEL
Page
-
Main Menu
Sub Menu
SPECIAL SET
USER TITLE
27
FOCUS MODE
20
SHARPNESS
27
FOCUS DIST
20
COLOR
28
ZOOM START
21
NEGATIVE
28
ZOOM END
21
D EFFECT
28
ZOOM SPEED
21
DETECTION
29
ZTRK MODE
21
LEVEL SET
29
WBC MODE
22
RED ADJUST
22
MOTION DET
OSD DISP
FUNCTION
29
MOTION DET
29
BLUE ADJUST
22
CAMERA ID
29
AE MODE
23
ZOOM MAG
29
IRIS ADJUST
23
USER TITLE
29
AGC ADJUST
24
INIT TITLE
29
BRIGHTNESS
24
P MASKING
BACKLIGHT
24
EXIT
E SENSITIVE
25
FLICKERLESS
25
SHUTTER
25
BLC LEVEL
26
WDR LEVEL
26
30
Exits the
Note: The Preset, Auto Pan, Pattern, Alarm, Privacy Mask functions could not be set
To set these functions, use LCC-K1000 protocol or Multix protocol.
18
Page
menu.
on
the OSD
-
menu.
LPT-OS553HQ_ENG_6602
7/19/07
2:08
Setting
Camera Menu
The buttons
on
PM
Page
19
FOCUS
the connected controller
are
used for
setup.
LCC-K1000 Controller
(Optional)
FOCUS MODE
PUSH AUTO
FOCUS DIST
50CM
ZOOM START
x1
ZOOM END
x54
ZOOM SPEED
QUICK
AUTO
ON
ZTRK MODE
OSD button
INITIAL SET
RETURN
CLR
(CLEAR)
button
ZOOM buttons
Arrow buttons
FOCUS buttons
SEL
(SELECT)
button
4.
Use ZOOM
5.
Use FOCUS
6.
To close
(In/Out)
to select
(Near/Far)
submenu
to select
a
To return to MENU
option.
value.
MENU, select [EXIT] option
MENU then press FOCUS
Use ZOOM
a
on
the
(Near/Far).
screen
from submenu
(In/Out) to select [RETURN] option then
(Near/Far) button on the sub menu.
press FOCUS
Open
1.
Menu
up and
2.
Display
Select the number of the
a
monitor to
Press OSD button
on
you want to set
MENU.
camera
display
the controller.
Note: Please refer to the manuals of the
Use ZOOM
FOCUS
(In/Out) to select
(Near/Far) button.
Submenu appears
on
an
option
the monitor.
Use ZOOM
screen
(In/Out) to select [EXIT] option then
(Near/Far) button on the main menu.
press FOCUS
con-
troller for details.
3.
To exit MENU
then press
To reset your parameters to the
default settings
Use ZOOM
(In/Out)
then press FOCUS
factory
to select [INITIAL SET] option
(Near/Far) button on the menu.
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
19
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Camera Identification
Only displays
20
Page
Setting
Select
the camera's ID. Use the internal
menu,
8 bit-DIP switch if you want to set ID.
?
Camera ID 0
ent of
control all of
can
camera
Focus Mode
?
independ-
camera
?
MENU
CAMERA ID
0
key
?
AE MODE
(NEAR
or
AE LEVEL
SPECIAL SET
?
F OSD DISP
P MASKING
manual pan, tilt
?
automatically changed
error or out of Focus,initialization of
system by using the "Remote Reset"
highly
recommended.
[FOCUS SET]
on
the
[MENU]
screen
2.
Press the
right key
[MANUAL].
FOCUS
Operation
to
to
on
If you want to activate the full-time auto focus
mode while a Pan/Tilt operation, set the focus
To avoid AF
cursor
automatically while
operation is performed.
or zoom
mode to AUTO.
Settings
Move the
when the
the controller is
If you press the FOCUS (NEAR or FAR) button
the controller while Auto-focus mode, the focus
mode is
EXIT
1.
on
Note:
MOTION DET
General
only
FAR) keys
only when
pressed.
AUTO: Auto-focus is activated
a
command of Controller is
the controller is
pressed.
AWB SET
LENS
on
MANUAL: Focus is activated
FOCUS
FOCUS SET
Focus
PUSH AUTO: Auto-focus is activated
the Push Auto
ID number.
setting
[FOCUS MODE] option on the [FOCUS]
then select the following mode.
and the FOCUS
setting
menu
FOCUS MODE
PUSH AUTO
FOCUS DIST
50CM
ZOOM START
x1
ZOOM END
x54
ZOOM SPEED
ZTRK MODE
QUICK
AUTO
INITIAL SET
ON
RETURN
appears.
FOCUS
FOCUS MODE
PUSH AUTO
FOCUS DIST
50CM
ZOOM START
x1
ZOOM END
x54
ZOOM SPEED
ZTRK MODE
INITIAL SET
Focus Distance
setting
Selects the minimum
shooting
Select
[FOCUS DIST] option
then select
QUICK
AUTO
ON
a
Move the
cursor
4.
Select
option (or value).
To reset the
6.
To return to the
use
20
on
the
[FOCUS] menu,
(1CM, 10CM,
50CM, 1M, 3M, 5M)
to the desired
option.
[FOCUS] settings to factory setting,
[INITIAL SET] option on the [FOCUS] menu.
option
the
FOCUS
3.
5.
on
Focus Distance value.
RETURN
an
distance for the focus.
previous menu,
[FOCUS] menu.
use
[RETURN]
FOCUS MODE
PUSH AUTO
FOCUS DIST
50CM
ZOOM START
x1
ZOOM END
x54
ZOOM SPEED
QUICK
AUTO
ON
ZTRK MODE
INITIAL SET
RETURN
7/19/07
LPT-OS553HQ_ENG_6602
Zoom Start
Selects
Select
a zoom
2:08
PM
Page
21
setting
start
position.
[ZOOM START] option on the [FOCUS]
a zoom's start position. (x1
x26)
then select
menu,
-
Zoom
Speed setting
Selects
a zoom
speed.
Select
[ZOOM SPEED] option on the [FOCUS]
a zoom speed. (SLOW, MIDDLE,
QUICK)
menu, then select
FOCUS
FOCUS
FOCUS MODE
PUSH AUTO
FOCUS DIST
50CM
FOCUS MODE
PUSH AUTO
ZOOM START
x1
FOCUS DIST
50CM
ZOOM END
x54
ZOOM START
x1
ZOOM SPEED
QUICK
AUTO
ON
ZOOM END
x54
ZOOM SPEED
QUICK
ZTRK MODE
AUTO
INITIAL SET
ON
ZTRK MODE
INITIAL SET
RETURN
RETURN
Zoom End
Selects
setting
a zoom
end
position.
Select
[ZOOM END] option on the [FOCUS]
then select a zoom's end position.
(Zoom Start position+1 x54)
menu,
Zoom
Tracking
Selects
a zoom
focused
Mode
tracking
zooming state.
setting
mode. Zoom
tracking
means
-
Select
[ZTRK MODE] option on the [FOCUS] menu,
a zoom tracking mode (AUTO, MANUAL).
then select
FOCUS
FOCUS
FOCUS MODE
PUSH AUTO
FOCUS DIST
50CM
ZOOM START
x1
FOCUS MODE
PUSH AUTO
ZOOM END
x54
FOCUS DIST
50CM
ZOOM SPEED
QUICK
AUTO
ON
ZOOM START
x1
ZOOM END
x54
ZOOM SPEED
QUICK
AUTO
ON
ZTRK MODE
INITIAL SET
RETURN
ZTRK MODE
INITIAL SET
RETURN
21
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Page
White Balance Control
You
can
[AWB]
set the white balance
Settings
options using
the
cursor
to
Select
[AWB SET]
on
the
[MENU]
screen
select
one
of four modes for white balance
[WBC MODE] option
following mode.
on
the
[AWB]
menu, then
select the
?
AUTO
0
and
FOCUS SET
White Balance): In this mode,
temperature is monitored continuously
(Auto-Tracing
the color
MENU
CAMERA ID
can
Balance
adjustment.
Operation
Move the
Setting the WBC (White
Control) Mode
You
menu.
General
1.
22
thereby
The color
AWB SET
balance is
AE MODE
white balance is
automatically
set.
temperature range for the proper white
approximately
2 500
-
9 500K.
Proper
white balance may not be obtained under the following conditions:
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
1)
The color
2)
9 500K range.
When the scene contains
temperature is
out of the 2 500
temperature objects, such
-
mostly high color
as a blue sky or
sunset.
2.
Press the
right key
and the AWB
setting
menu
3)
appears.
?
WBC MODE
AUTO
RED ADJUST
NOT USED
?
BLUE ADJUST
NOT USED
INITIAL SET
ON
cursor
4.
Select
option (or value).
5.
6.
an
to the desired
?
[AWB] settings to factory setting,
[INITIAL SET] option on the [AWB] menu.
option
on
the
previous menu,
[AWB] menu.
use
use
OUTDOOR: The color
MANUAL: You
approximately
3 200K.
temperature range for the
approximately
5 100K.
set the white balance
options
manually.
1) RED ADJUST: Obtains the optimum amount
of red gain.
2) BLUE ADJUST: Obtains the optimum amount
of blue gain.
can
WBC MODE
MANUAL
RED ADJUST
BLUE ADJUST
92
INITIAL SET
OFF
124
RETURN
[RETURN]
?
PUSH AUTO: The White Balance will be
automatically.
22
temperature range for the
AWB
option.
To reset the
To return to the
INDOOR: The color
is dim.
proper white balance is
RETURN
Move the
scene
proper white balance is
AWB
3.
When the
adjusted
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Page
AE Mode
Exposure Settings
You
can
set the exposure
options using
the
Selects
Select
General
select
Operation
Move the
cursor
to
?
[AE]
on
the
[MENU]
screen
MENU
CAMERA ID
an
setting
Automatic
[AE]
menu.
1.
23
[AE MODE] option on the [AE]
Automatic Exposure mode.
menu, then
an
AUTO: Use to
compensate the exposure automati-
cally.
?
0
IRIS MAN: Use to
(IRIS
FOCUS SET
AE MODE
?
SLOW MAN: The
available
SPECIAL SET
of
MOTION DET
change the value of Lens' Iris
manually, and the action of
compensation depend on its of AGC).
of lens is fixed
exposure
AWB SET
AE LEVEL
mode.
Exposure
(x1
camera
is
change of Electronic Sensitive is
x20 FIX). (Electronic Sensitive
fixed manually.)
FIX
-
F OSD DISP
?
P MASKING
SHUT MAN: Use to
control. In this
EXIT
(10 steps
2.
Press the
menu
right key
and the exposure
change
the Shutter
time, AE mode
control is
act
Speed
automatically
available).
setting
AE
appears.
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST
AUTO
AE MODE
AUTO
BRIGHTNESS
128
IRIS ADJUST
AUTO
BACKLIGHT
OFF
AGC ADJUST
AUTO
E SENSITIVE
x10 AUTO
BRIGHTNESS
128
FLICKERLESS
OFF
BACKLIGHT
OFF
SHUTTER
AUTO
E SENSITIVE
x10 AUTO
INITIAL SET
ON
FLICKERLESS
OFF
RETURN
SHUTTER
AUTO
INITIAL SET
ON
RETURN
Iris
3.
Move the
cursor
4.
Select
option (or value).
5.
To reset the
6.
an
to the desired
option.
only
[AE] settings to factory setting,
[INITIAL SET] option on the [AE] menu.
To return to the
option
on
the
previous menu,
[AE] menu.
use
Adjust setting
Selects
use
[RETURN]
a
when
Select
select
iris' exposure value. This option is available
[AE MODE] is set to [IRIS MAN].
[IRIS ADJUST] option
value. (0 255)
a
on
the
[AE]
menu, then
-
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST
AUTO
BRIGHTNESS
128
BACKLIGHT
OFF
E SENSITIVE
x10 AUTO
FLICKERLESS
OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
23
LPT-OS553HQ_ENG_6602
7/19/07
2:08
PM
Automatic Gain Control
Page
24
(AGC) setting
If the
images are too dark, change the maximum
[AGC] value to make the images lighter. This option
is available only when [AE MODE] is set to [SLOW
MAN] or [SHUT MAN].
Select
select
[AGC ADJUST] option
value. (0 7)
a
on
the
[AE]
Backlight Setting
Improves an image
backlighting.
Select
select
[BACKLIGHT] option
a
menu, then
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST
0
AUTO
BRIGHTNESS
128
IRIS ADJUST
AUTO
BACKLIGHT
OFF
AGC ADJUST
BRIGHTNESS
0
E SENSITIVE
x10 AUTO
128
FLICKERLESS
OFF
BACKLIGHT
OFF
SHUTTER
AUTO
E SENSITIVE
x10 AUTO
INITIAL SET
ON
FLICKERLESS
OFF
RETURN
SHUTTER
AUTO
INITIAL SET
ON
?
OFF: The back
?
ON: The back
?
AUTO
only
when
[AE MODE]
[BRIGHTNESS] option
value. (0 255)
on
is set to
the
[AE]
[AUTO].
menu, then
light compensation
is not used.
is used.
(Auto back light compensation): If you use
ordinary camera when there is an intense and
concentrated illumination behind an object, the
back light will shade the image on the monitor
screen. The Backlight function prevents such a
back light effect to secure a clear image under all
illumination environments.
-
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST
0
BRIGHTNESS
128
BACKLIGHT
OFF
E SENSITIVE
x10 AUTO
FLICKERLESS
OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
light compensation
an
?
24
menu, then
AE
The lens iris is fixed at the value that you have set
regardless of the brightness of an object. This option
a
[AE]
AE MODE
Brightness Setting
Select
the
-
RETURN
select
on
value.
AE
is available
that is darkened because of
WDR: The WDR
camera
is state of the art to
enlarge the screen profit effectively, especially for
taking photos of a window in a building. In short it
revives both the indoor and outdoor status as they
are clearly.
LPT-OS553HQ_ENG_6602
7/19/07
Electronic Sensitive
2:08
PM
25
Page
Shutter
setting
The electronic
varies the
low
sensitivity enhancement function
shutter speed to increase the sensitivity
in
conditions.
light
This
to
You
option is available only
[AUTO] or [SLOW MAN].
when
Select
[E SENSITIVE] option
select
a
There
are
on
[AE MODE]
the
[AE]
is set
menu, then
value.
two modes for Electronic Sensitive
as
fol-
Speed Setting
a shutter speed from among AUTO,
1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000,
1/10000, 1/20000 and 1/50000 seconds.
can
select
This
option is available only when [AE MODE] is
[AUTO] and [FLICKERLESS] option is set to
[OFF].
Select
select
[SHUTTER] option
shutter speed.
on
the
[AE]
menu, then
a
lows:
AE
AUTO mode:
select x20
matically
OFF, x2 AUTO x20 AUTO (If you
AUTO, the sensitivity is increased auto-
up to
-
x20.)
SLOW MAN mode: x1 FIX
x20
set
to
you select
is increased to a fixed x20.)
FIX, the sensitivity
-
x20 FIX
(If
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST
0
BRIGHTNESS
128
BACKLIGHT
OFF
E SENSITIVE
x10 AUTO
FLICKERLESS
OFF
SHUTTER
AUTO
ON
AE MODE
AUTO
INITIAL SET
IRIS ADJUST
AUTO
RETURN
AGC ADJUST
0
BRIGHTNESS
128
BACKLIGHT
OFF
E SENSITIVE
x10 AUTO
FLICKERLESS
OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
Flickerless
Setting
Use for
removing the flicker of picture.
available only when [AE MODE] is set
Select
This
to
option
[AUTO].
is
[FLICKERLESS] option on the [AE] menu,
an option (ON or OFF). Set to [ON] to
then select
remove
the flicker.
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST
0
BRIGHTNESS
128
BACKLIGHT
OFF
E SENSITIVE
x10 AUTO
FLICKERLESS
OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
25
7/19/07
LPT-OS553HQ_ENG_6602
Auto
You
can
Exposure
General
PM
Level
set the auto exposure
[AE LEVEL]
1.
2:08
Page
26
Settings
options using
the
menu.
to
cursor
Light Compensation)
[AE LEVEL]
Setting
Selects
a
level for the BLC
on
the
Select
[MENU]
(back light
[BLC LEVEL] option
then select
a
desired level
screen
MENU
CAMERA ID
Level
compensa-
tion).
Operation
Move the
BLC (Back
on
the
[AE LEVEL]
menu,
(0-255).
AE LEVEL
0
FOCUS SET
BLC LEVEL
176
AWB SET
WDR LEVEL
6
AE MODE
INITIAL SET
ON
AE LEVEL
RETURN
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
2.
Press the
setting
right key
menu
and the auto exposure level
appears.
AE LEVEL
WDR
(Wide Dynamic Range) Level
setting
Selects
a
level for the WDR
BLC LEVEL
176
WDR LEVEL
6
Select
INITIAL SET
ON
menu, then select
[WDR LEVEL] option
a
(Wide Dynamic Range).
on
the
desired level
[ AE LEVEL]
(0-255).
RETURN
AE LEVEL
3.
Move the
cursor
4.
Select
option (or value).
5.
To reset the
to
ting,
the
an
use
to the desired
option.
[AE LEVEL] settings
[INITIAL SET] option on
factory set[AE LEVEL]
menu.
6.
To return to the
option
26
on
the
previous menu, use [RETURN]
[AE LEVEL] menu.
BLC LEVEL
176
WDR LEVEL
6
INITIAL SET
ON
RETURN
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Page
27
User Title
Special Settings
You
can
set the
special options using
the
You
[SPECIAL]
menu.
General
1.
[MENU]
cursor
to
Move the
2.
[SPECIAL SET]
on
the
screen
Move the
select
3.
a
the
camera
to
cursor
[SPECIAL]
Operation
Move the
1.
Setting
can name
[USER TITLE]
on
the
Arrow mark appears.
menu.
arrow
independently.
mark to the desired
position
then
character.
Repeat step
2 to set the remain characters.
MENU
CAMERA ID
SPECIAL
0
m
FOCUS SET
AWB SET
USER TITLE
AE MODE
SHARPNESS
112
AE LEVEL
COLOR
ON
SPECIAL SET
NEGATIVE
OFF
MOTION DET
D EFFECT
NONE
F OSD DISP
INITIAL SET
ON
P MASKING
RETURN
EXIT
2.
Press the
menu
right key
and the
[SPECIAL] setting
appears.
Sharpness Setting
Sharpens
SPECIAL
Select
m
the
image
outline.
[SHARPNESS] option
a value. (0
menu, then select
USER TITLE
SHARPNESS
112
COLOR
ON
NEGATIVE
OFF
on
-
the
[SPECIAL]
255)
SPECIAL
D EFFECT
NONE
USER TITLE
INITIAL SET
ON
SHARPNESS
112
COLOR
ON
NEGATIVE
OFF
RETURN
D EFFECT
NONE
INITIAL SET
ON
RETURN
3.
Move the
cursor
4.
Select
option (or value).
5.
To reset the
use
an
to the desired
option.
[SPECIAL] settings to factory setting,
[INITIAL SET] option on the [SPECIAL]
menu.
6.
To return to the
option
on
the
previous
[SPECIAL]
menu,
use
[RETURN]
menu.
27
LPT-OS553HQ_ENG_6602
Color
You
7/19/07
2:08
PM
Page
28
Setting
Digital
switch the
can
displayed picture
to
grayscale
or
Effect
You cannot set
a
Setting
Digital
Effect
option.
color.
Select
[COLOR] option on the [SPECIAL] menu, then
option (ON or OFF). Set to [ON] to display
the picture with color. Set to [OFF] to display the picture with grayscale.
select
SPECIAL
USER TITLE
112
COLOR
ON
NEGATIVE
OFF
D EFFECT
NONE
INITIAL SET
ON
Negative Setting
can use
Select
the
negative
effect.
[NEGATIVE] option on the [SPECIAL]
an option (ON or OFF).
then select
SPECIAL
USER TITLE
SHARPNESS
112
COLOR
ON
NEGATIVE
OFF
D EFFECT
NONE
INITIAL SET
ON
RETURN
28
USER TITLE
SHARPNESS
112
COLOR
ON
NEGATIVE
OFF
D EFFECT
NONE
INITIAL SET
ON
RETURN
SHARPNESS
RETURN
You
SPECIAL
an
menu,
7/19/07
LPT-OS553HQ_ENG_6602
Motion Detection
2:08
PM
Page
29
Function On-Screen
Setting
The motion detection detects the
the
moving objects in
by monitoring changes in brightness level.
select the level of sensitivity for motion
scene
You
can
detection.
When this
camera
is connected to
a
compatible
ligent CCTV system, the camera transmits an
signal by multiplexing it with the video signal.
intel-
alarm
Display
Setting
You
can
using
set the Function On-Screen
the
[F OSD]
The Function On-Screen
be turned
1.
on or
Move the
Display options
menu.
Display
of this
camera can
off.
cursor
to
[F
OSD
DISP]
on
the
[MENU]
screen
1.
Move the
[MENU]
cursor
to
[MOTION DET]
on
the
MENU
screen
CAMERA ID
MENU
CAMERA ID
0
FOCUS SET
0
AWB SET
FOCUS SET
AE MODE
AWB SET
AE LEVEL
AE MODE
SPECIAL SET
AE LEVEL
MOTION DET
SPECIAL SET
F OSD DISP
MOTION DET
P MASKING
F OSD DISP
EXIT
P MASKING
EXIT
2.
2.
Press the
menu
right key
and the
[MOTION] setting
Press the
right key
and the
[F OSD] setting
menu
appears.
appears.
F OSD
MOTION
FUNCTION
DISP ON
DETECTION
ON
MOTION DET
DISP ON
LEVEL
10
CAMERA ID
DISP ON
DAY/NIGHT
AUTO
ZOOM MAG
DISP ON
INITIAL SET
ON
USER TITLE
DISP ON
RETURN
INIT TITLE
DISP ON
INITIAL SET
ON
RETURN
3.
3.
4.
Set
Use
[DETECTION] option
[LEVEL] option to
(21 levels).
to
[ON]
obtain the
to
use.
optimum
Use
[DAY/NIGHT] option
AUTO: The
camera
if the
is
picture is dark,
bright enough.
for
day/night
or
color mode if the
4.
on
the
on
screen.
the
Display
dose
screen.
To reset the
use
5.
DAY: Color mode enabled.
[F OSD] settings to factory setting,
[INITIAL SET] option on the [F OSD] menu.
To return to the
option
on
the
previous menu,
[F OSD] menu.
use
[RETURN]
To reset the
use
7.
OFF: The Function On-Screen
not appear
picture
NIGHT: Black-and-white mode enabled.
6.
?
Display
function.
selects black and white mode
option (DISP ON or OFF).
Displays the Function On-Screen
an
DISP ON:
detec-
tion level
5.
Select
?
[MOTION] settings to factory setting,
[INITIAL SET] option on the [MOTION] menu.
To return to the
option
on
the
previous menu,
[MOTION] menu.
use
[RETURN]
29
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
30
Page
5.
Privacy Masking Settings
Using the LCC-K1000 or controller
protocol for Privacy Zone Setting.
Adjust
with Multix
You can't
aiming at the protection of personal
privacy, selecting a screen part black not to be
displayed in the screen.
Up to 8 zones can be registered. Submenus are
provided for zone number selection and parameter
setting.
register
a new
privacy
zone
using
the
LCC-K1000
1.
change
into the
privacy mask zone and
privacy mask zone.
move
that the
you can't
The mask color will be
The
the
change into grey.
privacy zone setting has been completed and
setting is memorized in the camera's memory.
7.
Repeat steps
To
register
3-6 to add additional
a new
privacy
position.
the
using
protocol
zone
other controller with Multix
Press the Set Up button
[PRIVACY ZONE] icon.
so
frame with
zone
the size of
then select the
You must
use
mask
unit with Multix
1.
the LCC-K1000 controller to set the
zone.
If you
use
Protocol, refer
mask
on
the other controller
to follow
Use the command below to
frame
display
or
steps.
the blue
the center of monitor to set the
zone
privacy
zone.
Press SEL.
The sub
menu
will appear for
[PRIVACY ZONE]
Guide Code
setting.
3.
position
zoom
comes
Press SEL.
6.
privacy
2.
tilt, and
position
joystick.
the
This function is
To
the pan,
desired
Select
0x01
Dome ID
0x81
0x01
[Set
The sub
menu
Area] option
Check
0x00
Mask
(0xE5)
Zone
Index of
sum
then press SEL.
2.
will appear.
Adjust
the pan, tilt and
desired
3.
position
zoom
privacy
setting.
Guide Code
0x01
Dome ID
0x81
0x02
Index of
0x00
Mask
(0xE5)
The mask color will be
privacy
are
that the
so
frame.
zone
Use the command below to confirm the
mask
4.
position
into the
comes
zone
settings
Check
sum
changed into gray if the
completed. The settings
are
memorized in the camera's memory.
Notes:
4.
Use number buttons to select the
zone
index
number then press SEL to confirm.
The blue zone frame appears on the center of
?
The Check
8bit
?
monitor.
sum
sum
is calculated
of the all
by performing
bytes except check sum.
the
The P MASKING
menu option of the camera is
factory control. If you set the privacy
mask zone using the P MASKING menu option of
the camera, the privacy mask function may cause
used for
a
?
malfunction.
Please contact authorized service center
you
30
purchased
to know the all of the
or
where
protocol.
7/19/07
LPT-OS553HQ_ENG_6602
2:08
PM
Page
31
Reference
Specifications
NTSC
Signal System
Pick-Up
(High Resolution)
1/4" EX-view HAD CCD
Total Pixels No.
410K
470K
S/N Ratio
More Than 50 dB
Horizontal Resolution
More Than 520 TV Lines
Lens
X 27 Zoom
Shooting
PAL
(High Resolution)
Device
Distance
On Screen
Tele
F
(F 1.5(W),
(1.2m),
f=3.25-88.0
3.8(T)
Wide
mm)
(0.01 m)
On/Off
Display
Minimum Illumination
1 Lux
(F1.5, normal shutter)
(20 Field Accumulated)/
(Infrared ON: Night Mode)
0.03 Lux
0 Lux
Zoom
Digital
x
2: Basic
Sync System
White Balance
Auto
(ATW)/
Control Method
Alarm
Input
Video
Output
(Off
at
WDR)
Internal
Indoor/ Outdoor/ Manual/ Push Auto
RS-485 Control
4 Channel
Composite Output
Electronic Shutter
1/60
-
1/50,000
Sec
1
Vp-p,
(10 Step)
Flickerless Mode
Manual On/Off
Iris Control
Auto / Manual
Wide
Dynamic Range
Dual Shutter control
Panning Range (Speed)
0°
Tilting Range (Speed)
0°
Privacy
Zone
-
(128
(120°
/
Sec)
180°
(120°
/
Sec)
Programmable
Panning
Groups
-10°
50°C
Safekeeping Temperature
-20°
Tour
Consumption
(ø
-
-
60°C
DC 12V
Supply
Dimension
Weight
Zone
2-8points
Operation Temperature
Power
Dynamic Range)
Max. 5 minutes
Max. 9
Power
1/50,000 Sec (10 Step)
128 Position / 256
Pattern
Group
-
times of
350°
8 Area Active
Preset / ID
Auto
-
75Ω
1/50
x
H)
Max. 12W
ø174
x
167.3
mm
Approx 2.9Kg
31
LPT-OS553HQ_ENG_6602
P/NO
:
7/19/07
MFL40426602
2:08
PM
Page
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising