LG | CM2460 | LG CM2460 Owner’s Manual

OWNER’S MANUAL
Micro Hi-Fi
Audio
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
CM2460 (CM2460, CMS2460F)
*MFL69389523*
www.lg.com
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from overheating.
The openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance, contact
an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure.
CAUTION concerning the Power cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the appliance. The Power Plug is the disconnecting
device. In case of an emergency, the Power Plug must
remain readily accessible.
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: No naked flame sources, such as lighted
candles, should be placed on the apparatus.
Symbols
~
0
Refers to alternating current(AC).
Refers to direct current(DC).
1
Refers to class II equipment.
Getting Started
Safety way to remove the battery or the battery
from the equipment: Remove the old battery
or battery pack, follow the steps in reverse order
than the assembly. To prevent contamination of
the environment and bring on possible threat
to human and animal health, the old battery or
the battery put it in the appropriate container at
designated collection points. Do not dispose of
batteries or battery together with other waste. It is
recommended that you use local, free reimbursement
systems batteries and accumulators. The battery
shall not be exposed to excessive heat such as
sunshine, fire or the like.
3
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
4
Table of Contents
Table of Contents
3Operating
1
Getting Started
2
6
6
7
7
7
7
8
10
11
Safety Information
Unique Features
Accessories
Playable file Requirement
– Music file requirement
– Compatible USB Devices
– USB device requirement
Remote control
Front Panel
Rear Panel
14
14
14
15
15
15
15
2Connecting
12
12
13
13
13
Connecting to speakers
– Connecting the speakers to the unit
Optional Equipment Connection
– USB Connection
– PORT. IN Connection
Basic Operations
– CD/USB Operations
– Auto Play
Other Operations
– Programmed Playback
– Deleting Programmed list
– Displaying file information
(ID3 TAG)
16 – Searching for a folder and an MP3/WMA/
FLAC file
16 – Deleting an MP3/WMA/FLAC file
16 – Turn off the sound temporarily
17 – Sleep Timer Setting
17 – Dimmer
17 – DEMO
17 – Auto power down
18 – AUTO POWER On
18 – Auto function change
19 Using a BLUETOOTH® wireless technology
19 – Listening to music stored on the
BLUETOOTH devices
21 Using the Music Flow Bluetooth App
21 – Install “Music Flow Bluetooth” App onto
Your Bluetooth Device
23 Radio Operations
23 – Listening to the radio
23 – Improving poor FM reception
23 – Presetting the Radio Stations
23 – Deleting all the saved stations
24 Sound adjustment
24 Advanced Operations
24 – Recording to USB
25 – To select recording bit rate and speed
26 Setting the Clock
26 – Setting the Clock through
“Music Flow Bluetooth” App
26 – Using your player as an alarm clock
27 LG Sound Sync
Table of Contents
5
4Troubleshooting
28
Troubleshooting
5Appendix
29 Main unit
30 Speakers
31Maintenance
31 – Handling the Unit
31 – Notes on Discs
31 Trademarks and Licenses
1
2
3
4
5
6
Getting Started
Unique Features
1
BLUETOOTH
Accessories
Please check and identify the supplied accessories.
Getting Started
Listens to music stored on your Bluetooth device.
USB Direct Recording
Records music to your USB device.
Music Flow Bluetooth
Music Flow Bluetooth is an app designed to let you
take control of some of LG’s latest audio devices.
Refer to page 21-22
LG Sound Sync
Controls volume level of this unit by the remote
control of your LG TV that is compatible with LG
Sound Sync.
Remote Control (1)
Batteries (2)
Getting Started
7
Playable file
Requirement
Compatible USB Devices
Music file requirement
yy The USB function of this unit does not support all
USB devices.
yy Sampling frequency :
MP3 : within 8 to 48 kHz
WMA : within 8 to 48 kHz
FLAC : within 8 to 192 kHz (USB),
within 8 to 48 kHz (CD)
yy USB Flash Drive :
Devices that support USB2.0 or USB1.1.
USB device requirement
yy Devices which require additional program
installation when you have connected it to a
computer, are not supported.
yy Do not extract the USB device while in operation.
yy Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy For a large capacity USB, it may take a few minute
to be searched.
yy Maximum files : Data CD : 999 / USB : 2000
yy To prevent data loss, back up all data.
yy Maximum folders : Data CD : 99 / USB : 200
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy File extensions : “.mp3”/ “.wma”/ ”.flac”
yy Certain MP3/WMA/FLAC files may not be played
depending on the type or format of the file.
yy CD-ROM file format : ISO 9660/JOLIET
yy We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
yy Support channel (FLAC) : Up to 2 channel
yy Support output bit/sample (FLAC) : 24 bit
yy bps (FLAC) : Up to 2.5 Mbps
The DTS is not supported. In case of DTS audio
format, audio is not output.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot use
it on LG players.
(Mastered/Live File System : Disc format system for
Windows Vista)
yy Using NTFS file system is not supported.
(Only FAT(16/32) file system is supported.)
yy This unit recognizes up to 2000 files.
yy External HDD, card readers, locked devices, or hard
type USB devices are not supported.
yy USB port of the unit cannot be connected to the
PC. The unit cannot be used as a storage device.
yy Some USB may not work with this unit.
1
Getting Started
MP3/WMA/FLAC file compatibility with this unit is
limited as follows.
yy MP3 Player : Flash type MP3 player.
8
Getting Started
Remote control
• • • • • • • • • • • • • • a• • • • • • • • • • • • • •
1 (Power) : Switches the unit ON or OFF.
B (Open/Close) : Opens and closes the disc tray.
VOL +/- : Adjusts speaker volume.
1
Getting Started
PRESET/FOLDER W/S :
-- Searches for a folder of MP3/WMA/FLAC files.
When a CD/USB containing MP3/WMA/FLAC
files in several folders is being played, press
PRESET/FOLDER W/S to select the folder you
want to play.
-- Chooses a preset number for a radio station.
FUNCTION : Selects the function and input source.
@ : Mutes the sound.
PROGRAM/MEMORY :
-- Stores radio stations.
-- Deletes all the saved stations.
-- Creates a programmed list you want to listen to.
REPEAT : Plays your tracks/files repeatedly or
randomly.
DELETE :
-- Deletes MP3/WMA/FLAC files.
-- Deletes a song on the programmed list.
Replacement of battery
)
(R03
(R03)
Remove the battery cover on the rear of the remote
control, and insert the battery with 4 and 5
matched correctly.
Getting Started
9
• • • • • • • • • • • • • • c• • • • • • • • • • • • • •
SOUND EFFECT : Chooses sound impressions.
INFO :
-- Sees information about your music. An MP3 file
often comes with ID3 tag. The tag gives the Title,
Artist, Album or Time information.
-- Sees the address of connected Bluetooth device
in Bluetooth mode.
TUN. -/+ : Selects the radio stations.
C/V (Skip/Search) :
-- Skips fast backward or forward.
-- Searches for a section within a track/file.
d/M (Play/Pause) :
-- Starts or pauses playback.
-- Selects STEREO/MONO.
Z (Stop) :
-- Stops playback or recording.
-- Cancels DELETE function
DIMMER : The display windows dims over few steps.
SLEEP : Sets the system to turn off automatically at
a specified time.
CLOCK : Sets a clock and checks a time.
ALARM : With the ALARM function you can turn CD,
USB play and Tuner reception on at a desired time.
SET : Confirms the setting.
USB REC : USB direct recording.
? : The button is not available for any function.
1
Getting Started
• • • • • • • • • • • • • • b• • • • • • • • • • • • • •
10 Getting Started
Front Panel
1
Getting Started
a
b
c
d
e
f
h
g
i
j
k
a 1/! (Power)
Switches the unit ON or OFF.
fRemote sensor
b F
Selects the function or input source.
h Volume Knob
Adjusts volume of speaker.
c Y/U (Skip/Search)
- Searches backward or forward.
- Skips to the previous/next track/file.
iUSB
Plays the audio files by connecting the USB
device.
TUNING - / +
Selects the radio stations.
d T (Play/Pause)
- Starts or pauses playback.
- Selects Stereo/Mono.
e R
Opens or closes the disc tray.
g Display window
j Disc tray
kPORT. IN
Connects to a Portable device.
Getting Started 11
Rear Panel
1
Getting Started
a
b
a FM ANTENNA
b SPEAKERS (L/R) terminals
cPOWER IN
R (6 Ω)
L (6 Ω)
c
12 Connecting
Connecting to speakers
Connecting the speakers to the
unit
2
To connect the cable to the unit, press each plastic
finger pad to open the connection terminals on the
unit. Insert the wire and release the finger pad.
Connecting
Connect the black of each wire to the terminals
marked - (minus) and the other end to the terminals
marked + (plus).
Color
Speaker
Red
Front R
White
Front L
>>Caution
yy Make sure children do not put their hands or
any objects into the *speaker duct.
* Speaker duct : A hole for plentiful bass
sound on speaker cabinet (enclosure)
yy Use the speaker supplied with this unit only.
Using any other speaker may cause
malfunction.
yy The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far
away from either TV screen or PC monitor.
Connecting 13
Optional Equipment
Connection
PORT. IN Connection
Connect an output (earphone or line out) of portable
device (MP3 or PMP etc) to the PORT. IN connector.
USB Connection
Connect a USB device to the USB ports on the unit.
2
Connecting
Portable cable
MP3 player etc.
,,Note
Removing the USB device from the unit.
1. Choose a different function/mode or
press Z on the remote control twice in a
row.
2. Remove the USB device from the unit.
Listening to music from your portable
player or external device
The unit can be used to play the music from many
types of portable player or external device.
1. Connect the portable player to the PORT. IN
connector of the unit.
2. Turn the power on by pressing 1/!.
3.Press F to select PORTABLE function.
4. Turn on the portable player or external device and
start it playing.
14 Operating
Basic Operations
CD/USB Operations
1. Insert the disc by pressing B on the remote
control or R on the unit.
Or connect the USB device to the USB port.
2. Select CD or USB function by pressing
FUNCTION on the remote control or F on the
unit.
To
3
Stop
Do this
Press Z on the remote control.
Operating
Playback
Press d/M on the remote control
or T on the unit.
Pause
Press d/M on the remote control
or T on the unit.
Searching
for a section
within
a track/file
Press and hold C/V on the
remote control or Y/U on the
unit during playback and release it at
the point you want to listen to.
-- In stop status,
Press C/V on the remote
control or Y/U on the unit to
go to the next/previous track/file.
-- During playback,
Skipping to
the next/
previous
track/file
press V on the remote control or
U on the unit to go to the next
track/file.
Playing less than 2 seconds, press
C on the remote control or Y
on the unit to go to the previous
track/file.
Playing after 3 seconds, press C
on the remote control or Y on
the unit to go to the beginning of
the track/file.
Playing
Press REPEAT on the remote
repeatedly or control repeatedly. Refer to the note
randomly for details about the display change.
,,Note
yy The display changes in the following order.
USB
MP3/WMA/FLAC
CD
AUDIO CD
RPT 1
RPT 1
RPT 1
RPT*DIR
RPT DIR
-
RPT ALL
RPT ALL
RPT ALL
RANDOM
RANDOM
RANDOM
OFF
OFF
OFF
*DIR : Directory
yy When you play programmed list, only RPT 1
and RPT ALL are available.
yy Even after restarting the unit or switching
one function to another, you can listen to
music from the point where it’s last been
played.
yy If you leave the disc tray open for 5 minutes,
it will close automatically.
Auto Play
AUDIO/MP3/WMA/FLAC CD is played automatically
after disc tray is open and then closed.
Automatically switches to the CD function if disc tray
is open and then closed when there is no disc in tray.
Operating 15
Other Operations
Programmed Playback
Deleting Programmed list
Deleting function only works in the edit mode.
1.Press PROGRAM/MEMORY on the remote
control in stop status.
The program function enables you to store your
favorite files from any disc or USB device.
2. Select a song by pressing PROGRAM/MEMORY
or PRESET/FOLDER W/S repeatedly.
A program can contain 20 tracks/files for each media
(CD, USB). Possible to save a total of 40 tracks/files.
3.Press DELETE while a song is selected.
1.Press PROGRAM/MEMORY on the remote
control in stop status.
2.Press C/V on the remote control to select
a track/file.
3.Press PROGRAM/MEMORY to save and select a
next track/file.
5.Press PROGRAM/MEMORY once again.
To play the programmed list, press d/M after you
make the list.
,,Note
When making or modifying the programmed
list, REPEAT mode is off.
yy Program is switched off in the case below.
-- Changing to a different function.
-- Turning off and on the unit.
Displaying file information
(ID3 TAG)
While playing an MP3 file containing file information,
you can display the information by pressing INFO.
3
Operating
4. Repeat steps 2 - 3 to store other tracks/files.
(You can modify the list by pressing
PRESET/FOLDER W/S to select the program
number.)
,,Note
yy Programmed list is cleared in the case below.
-- Removing the disc or the USB device.
-- Deleting or recording music files in the USB
device.
-- Unplugging the power cord.
16 Operating
Searching for a folder and an
MP3/WMA/FLAC file
Deleting an MP3/WMA/FLAC
file
1.Press PRESET/FOLDER W/S on the remote
control repeatedly until a desired folder appears
in the display window.
You can delete file, folder or format by pressing
DELETE on the remote control. This function is
supported only in stop status. (USB only)
2.Press d/M to play it. The first file of the folder
will be played.
1. -Select the file you want to delete and press
DELETE on the remote control.
,,Note
yy USB/CD Folders/Files are recognized as
below
ROOT
FOLDER
-Select the folder you want to delete by pressing
PRESET/FOLDER W/Son the remote control
and press DELETE on the remote control.
-Press and hold DELETE on the remote control
to format the USB device.
Or
FILE
3
FOLDER1
FOLDER3
Press DELETE on the remote control repeatedly
during selecting the MP3/WMA/FLAC file.
Operating
FILE 5
FILE 6
The display changes in the following order.
FILE 7
FOLDER4
FOLDER7
FILE 3
FOLDER8
- DEL FILE : Deletes file
- DEL DIR : Deletes folder
- FORMAT : Formats USB
FILE 8
FILE 9
FILE 10
FILE 4
2. To delete file/folder or format, press d/M
on the remote control.
FOLDER2
FOLDER5
FILE 11
FILE 12
FOLDER6
FILE 13
FILE 14
FILE 1
FILE 2
yy If there is no file in a folder, the folder will not
appear.
yy Folders will be presented as the following
order;
ROOT FOLDER1 FOLDER3 FOLDER7
FOLDER8 FOLDER5 FOLDER6
yy File will be played from $ file No.1 to $ file
No.14 one by one.
yy Files and folders will be presented in order
recorded and may be presented differently
according to the record circumstances.
yy *ROOT : The first screen you can see when a
computer recognize the USB/CD is “ROOT”.
If you want to exit the current mode,
press Z on the remote control.
>>Caution
yy Do not extract the USB device during
operation. (play, delete, etc.)
yy Regular back up is recommended to prevent
data loss.
yy The delete function may not be supported
according to the USB device.
Turn off the sound temporarily
Press @ on the remote control to mute your
sound.
You can mute your unit, for example, to answer the
telephone, the “MUTE” will appear in the display
window.
To cancel it, press @ again or change the volume
level.
Operating 17
Sleep Timer Setting
Press SLEEP repeatedly to select delay time
between 10 and 180 minutes. After the delay time,
the unit will be turned off.
To cancel the sleep function, press SLEEP repeatedly
until “SLEEP 10” appears, and then press SLEEP
once again.
,,Note
yy You can check the remaining time before the
unit is turned off.
yy Press SLEEP. The remaining time appears in
the display window.
Press DIMMER once.
The display windows dims over few steps.
To cancel it, press DIMMER again.
DEMO
In the power on state, adjust the volume level of the
main unit to minimum and then press and hold F on
the unit for about 7 seconds.
To cancel the DEMO function, press and hold the F on
the unit for about 7 seconds.
This unit will turn itself off to save electricity in the
case were the main unit is not connected to an
external device and is not used for 20 minutes.
The unit will also turn itself off after six hours if the
main unit has been connected to another device
using the analog inputs.
How to disconnect the wireless
network connection or the wireless
device
Turn off the unit by pressing the power button for
more than 5 seconds.
3
Operating
Dimmer
Auto power down
18 Operating
AUTO POWER On
Auto function change
This unit automatically turns on by an input source :
LG TV or Bluetooth
This unit recognizes input signals such as Bluetooth
and LG TV and then changes suitable function
automatically.
If you try to connect your Bluetooth device, this
unit turns on and the unit will be connected your
Bluetooth device.
,,Note
yy Depending on the connected device, this
function may not operate.
yy Depending on the connected device, the unit
turns on but Bluetooth function may not be
connected.
3
Operating
yy If you disconnect Bluetooth connection by
this unit, some Bluetooth devices try to
connect to the unit continually. Therefore it is
recommended to disconnect the connection
before turning off the unit.
yy If you try to connect to the “Music Flow
Bluetooth” app, Bluetooth function of this
unit is turned on.
yy If you turn on the unit using LG TV or
Bluetooth function, proper function of this
unit is turned on.
yy If you have already paired with this unit,
automatically this unit can turn on by an
input source when this unit is turned off.
yy If you turn off the unit by pressing the power
button for more than 5 seconds, Auto Power
On function is disabled.
To activate it, turn on the unit.
yy To use this function, the main unit must be
registered in paired devices list of Bluetooth
device.
When you try to connect Bluetooth
device
When you try to connect your Bluetooth device to
this unit, Bluetooth function is selected. Play your
music on the Bluetooth device.
When LG TV is connected
When you turn on your LG TV connected by LG
Sound Sync, this unit changes the function to LG TV.
You can hear the sound from your TV.
,,Note
yy This function is not available during recording
or deleting.
yy This function only works with devices that
were previously connected.
Operating 19
Using a BLUETOOTH®
wireless technology
About BLUETOOTH
Bluetooth is wireless communication technology for
short range connection.
The sound may be interrupted when the connection
has interference from other electronic devices or you
connect a Bluetooth device from a different room.
Connecting individual devices under Bluetooth
wireless technology does not incur any charges. A
mobile phone with Bluetooth wireless technology
can be operated via the Cascade if the connection
was made via Bluetooth wireless technology.
BLUETOOTH Profiles
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles. This
unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
Codec : SBC
Pairing your unit and BLUETOOTH
device
Before you start the pairing procedure, make
sure the Bluetooth feature is activated on your
Bluetooth device. Refer to your Bluetooth device’s
user guide. Once a pairing operation is performed, it
does not need to be performed again.
1. Turn on the unit.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device
display depending on the type of Bluetooth
device. Your unit appears as “LG CM2460(XX)”.
,,Note
yy XX means the last two digits of
Bluetooth address. For example, if your
unit has a Bluetooth address such as
9C:02:98:4A:F7:08, you will see
“LG CM2460(08)” on your Bluetooth device.
yy Depending on the Bluetooth device type,
some devices may have a different pairing
process. Enter the PIN code (0000) as
needed.
yy You can connect this unit with up to 3
Bluetooth devices simultaneously using the
same method as described above, only in the
Bluetooth function.
yy The multi pairing connection is only
supported on Android or iOS devices. (Multi
pairing connection may not be supported
depending on the connected device
specifications.)
yy Removable/detachable Bluetooth device
(Ex : Dongle etc.) will not support multi
pairing.
3
Operating
Available Devices : Mobile phone, MP3, Laptop, PDA.
Listening to music stored on the
BLUETOOTH devices
20 Operating
3. When this unit has successfully connected with
your Bluetooth device, “PAIRED” will be appear
on the display window. After a short amount
of time, the Bluetooth device name will be
displayed.
,,Note
yy “PAIRED” will momentarily appear on the
display when you connect other devices for
multi pairing
yy If the device name is unavailable, “_” will be
displayed.
3
4. Listen to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
Operating
,,Note
yy When using Bluetooth technology, you have
to make a connection between the unit and
the Bluetooth device as close as possible and
keep the distance.
However, it may not work well in certain
situations as described below:
-- There is a obstacle between the unit and
the Bluetooth device.
-- There is a device using same frequency
with Bluetooth technology such as a
medical equipment, a microwave or a
wireless LAN device.
,,Note
yy When this unit connected with multiple
Bluetooth devices, only one device which
you are playing keeps Bluetooth connection
when you change the function to the others.
yy The sound may be interrupted when the
connection has interference from other
electronic devices.
yy You cannot control the Bluetooth device
with this unit.
yy Depending on the type of the device, you may
not be able to use the Bluetooth function.
yy You can enjoy wireless system using phone,
MP3, Notebook, etc.
yy The more distance between the unit and
the Bluetooth device, the lower the sound
quality becomes.
yy Bluetooth connection will be disconnected
when the unit is turned off or the Bluetooth
device gets far from the unit.
yy When Bluetooth connection is disconnected,
connect the Bluetooth device to the unit
again.
yy When a Bluetooth device is not connected,
“BT READY” appears on the display window.
yy When you use Bluetooth function,
adjust the volume to a proper level on the
Bluetooth device.
yy You should connect your Bluetooth device to
this unit again when you restart it.
yy If it is not in Bluetooth function, only one
device can be connected.
yy Even if this unit connected up to 3 Bluetooth
devices in the Bluetooth mode, you can play
and control music by using only one of the
connected devices.
yy If a Bluetooth device is connected when
using LG TV, LG TV is disconnected and the
Bluetooth device is connected.
yy When you connect Bluetooth device (iOS
device etc.) to this unit or operate the device,
the volume level can be synchronized with
each other.
Operating 21
Using the Music Flow
Bluetooth App
Install “Music Flow Bluetooth” App
through “Google Android Market
(Google Play Store)”
1. Tap the “Google Android Market (Google Play
Store)” icon.
,,Note
Only Android OS is available to use “Music Flow
Bluetooth” app with this unit.
About “Music Flow Bluetooth” App
“Music Flow Bluetooth” app brings a suite of new
features to this unit.
To enjoy more features, you are recommended to
download and install free “Music Flow Bluetooth”
app.
There are two ways to install “Music Flow Bluetooth”
app onto your Bluetooth device.
Install “Music Flow Bluetooth” App
through QR code
1. Install “Music Flow Bluetooth” app through QR
code. Use the scanning software to scan the QR
code.
(Android OS)
2. Tap an icon for installation.
3. Tap an icon for downloading.
,,Note
yy Make sure that your Bluetooth device is
connected to the internet.
yy Make sure that your Bluetooth device
has a scanning software application. If you
don’t have one, download one from “Google
Android Market (Google Play Store)”.
yy Depending on area, QR code may not work.
3. In the search result list, find and tap
“Music Flow Bluetooth” to start downloading
Bluetooth app.
4. Tap an icon for installation.
5. Tap an icon for downloading.
,,Note
yy Make sure that your Bluetooth device is
connected to the Internet.
yy Make sure that your Bluetooth device is
equipped with “Google Android Market
(Google Play Store)”.
3
Operating
Install “Music Flow Bluetooth”
App onto Your Bluetooth Device
2. In the search bar, type in the “Music Flow
Bluetooth” and search it.
22 Operating
Activate Bluetooth with
“Music Flow Bluetooth” App
“Music Flow Bluetooth” app helps to connect your
Bluetooth device to this unit.
1.Tap “Music Flow Bluetooth” app icon on the home
screen to open “Music Flow Bluetooth” app, and
go to the main menu.
2. Tap [Menu] and select the unit you want.
3. If you want to get more information to operate,
tap [Help] on the [Setting] menu.
,,Note
3
yy “Music Flow Bluetooth” app will be available
in the software version as follow;
-- Android O/S : Ver 4.0.3 (or later)
Operating
yy If you use “Music Flow Bluetooth” app for
operation, there would be some differences
between “Music Flow Bluetooth” app and
the supplied remote control. Use the supplied
remote control as necessary.
yy Depending on the Bluetooth device, “Music
Flow Bluetooth” app may not work.
yy After connection of “Music Flow Bluetooth”
app, music may be output from your device. In
this case, try connecting procedure again.
yy If you operate the other applications or
change the settings on your Bluetooth
device while using “Music Flow Bluetooth”
app, “Music Flow Bluetooth” app may operate
abnormally.
yy When “Music Flow Bluetooth” app operates
abnormally, check your Bluetooth device and
the connection of “Music Flow Bluetooth” app
and then try to connect again.
yy Depending on the Smartphone's operating
system, you have some differences for “Music
Flow Bluetooth” operation.
yy Check Bluetooth setting on your Bluetooth
device if “Music Flow Bluetooth” app
connection does not work well.
Operating 23
Radio Operations
Presetting the Radio Stations
Listening to the radio
1.Press FUNCTION on the remote control or F on
the unit until FM appears in the display window.
1.Press FUNCTION on the remote control or F on
the unit until FM appears in the display window.
The last received station is tuned in.
2. Auto tuning :
Press and hold TUN. -/+ on the remote control
or Y/U on the unit for about two seconds
until the frequency indication starts to change,
then release. Scanning stops when the unit tunes
in a station.
Or
3. Adjust the volume by rotating volume knob on
the unit or by pressing VOL +/- on the remote
control repeatedly.
Improving poor FM reception
Press d/M on the remote control or T on the
unit.
This will change the tuner from stereo to mono and
usually improve the reception.
2. Select the desired frequency by pressing
TUN. -/+ on the remote control or Y/U
on the unit.
3.Press PROGRAM/MEMORY on the remote
control. A preset number will blink in the display
window.
4.Press PRESET/FOLDER W/S on the remote
control to select the preset number you want.
5.Press PROGRAM/MEMORY on the remote
control. The station is stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen to a preset station, press
PRESET/FOLDER W/S on the remote control.
Deleting all the saved stations
1. Press and hold PROGRAM/MEMORY on the
remote control for two seconds.
“ERASEALL” will flash up on the unit display.
2.Press PROGRAM/MEMORY on the remote
control to erase all the saved radio stations.
3
Operating
Manual tuning :
Press TUN. -/+ on the remote control or
Y/U on the unit repeatedly.
You can preset 50 stations for FM.
Before tuning, make sure to turn down the volume.
24 Operating
Sound adjustment
Advanced Operations
This system has a number of pre-set surround sound
fields. The displayed items for the equalizer may be
different depending on sound sources and effects.
Recording to USB
You can select a desired sound mode by using
SOUND EFFECT on the remote control.
On Display
3
POP
CLASSIC
ROCK
JAZZ
Operating
BASS
STANDARD
Description
This program lends
an enthusiastic
atmosphere to the
sound, giving you the
feeling you are at an
actual rock, pop, jazz
or classic concert.
Reinforces the treble,
bass and surround
sound effect.
You can enjoy
optimized sound.
,,Note
yy O
n some speakers, sound may not be heard
or heard in low sound depending on the
sound mode.
yy M
aybe you need to reset the sound mode,
after switching the input, sometimes even
after the sound track changed.
You can record a various sound source to USB.
(CD, Tuner, PORTABLE)
1. Connect the USB device to the unit.
2. Select a function by pressing FUNCTION on the
remote control or F on the unit.
One track/file recording - You can record to USB
after playing a track/file you want.
All tracks/files recording - You can record to USB
after full stop status.
Programmed list recording - After showing the
programmed list, you can record it to USB.
(Refer to page 15)
3. Start the recording by pressing USB REC on the
remote control.
4. To stop recording, press Z on the remote control.
Pausing recording
During recording, press d/M on the remote control
or T on the unit to pause recording.
Press it again to restart recording.
(Only Tuner, PORTABLE)
Operating 25
To select recording bit rate and
speed
,,Note
1.Press USB REC on the remote control for longer
than 3 seconds.
yy You can check the recording percentage rate
for the USB record on the display window
during the recording.
(MP3/WMA/FLAC CD Only)
2.Use C/V on the remote control or
Y/U on the unit to select the bit rate.
yy During recording MP3/WMA/FLAC, there is no
sound.
3.Press USB REC on the remote control again to
select the recording speed.
yy When you stop recording during playback, the
file that has been recorded at that time will be
stored. (Except MP3/WMA/FLAC files)
4.Press C/V on the remote control or
Y/U on the unit to select a desired
recording speed :
(AUDIO CD only)
X1 SPEED
- You can listen to music while recording it.
5.Press USB REC on the remote control to finish
the setting.
The making of unauthorized copies of
copy-protected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
yy If USB recording does not work, the message
like “NO USB”, “ERROR”, “USB FULL” or
“NO REC” is displayed on the display window.
yy Multi card reader device or external HDD
cannot be used for USB recording.
yy A file is recorded by about 512 Mbyte when
you record for a long term.
yy You may not store more than 2000 files.
yy In case of the unsupported MP3/WMA/FLAC
file, the file recording may be stopped.
yy It’ ll be stored as follows.
AUDIO CD
MP3/WMA/FLAC
PORTABLE
Tuner
Tuner : The current recording frequency is
shown.
3
Operating
X2 SPEED
- You can just record the music file.
yy Do not remove the USB device or turn off
the unit during USB recording. If does not, an
incomplete file may be made and not deleted
on PC.
26 Operating
Setting the Clock
1. Turn the unit on.
1. Turn the unit on.
2. Press and hold CLOCK.
2. Press and hold ALARM.
3. Select time mode by pressing C/V on the
remote control.
3.Press C/V on the remote control or
Y/U on the unit to change the hours and
minutes and press SET to save.
- AM 12:00 (for an AM and PM display) or 0:00
(for a 24 hour display)
4.Press SET to confirm your selection.
5. Select the hours by pressing C/V on the
remote control.
6.Press SET.
3
Using your player as an alarm
clock
7. Select the minutes by pressing C/V on
the remote control.
Operating
8.Press SET.
Setting the Clock through
“Music Flow Bluetooth” App
Install “Music Flow Bluetooth” app on your Android
device. (Refer to page 21)
Your unit’s clock will be automatically synchronized
with your device by activating Bluetooth connection
through “Music Flow Bluetooth” app.
4. Press C/V on the remote control or
Y/U on the unit to select function and
press SET to save.
-- Press C/V to select a memory No. when
you select tuner and then, press SET. If there is
no memory No., this step is skipped.
5.Press C/V on the remote control or
Y/U on the unit to change the volume
and press SET to save. The clock icon “(“ shows
that the alarm is set.
,,Note
yy If you set the clock, you can check the time
by pressing CLOCK even when the player is
turned off.
yy You can set alarm after you set the clock.
yy If you set the clock and alarm, you can check
the alarm icon “(“ by pressing CLOCK even
when the player is turned off.
yy If you set the clock and alarm, you can check
the alarm icon “(“ and setting information
by pressing ALARM even when the unit is
turned off.
yy You can select ALARM on/off mode by
pressing ALARM.
Operating 27
LG Sound Sync
1. Turn on the unit by pressing 1 (Power) on the
remote control.
2.Press FUNCTION on the remote control or F on
the unit until LG TV function is selected.
You can control some functions of this unit by
your TV’s remote control with LG Sound Sync. It is
compatible with LG TV that supports LG Sound Sync.
Make sure your TV has the LG Sound Sync logo.
Controllable function by LG TV’s remote control :
Volume up/down, mute
Refer to the TV’s instruction manual for the details of
LG Sound Sync.
,,Note
yy If the connection fails, check the conditions of
this unit and your TV : power, function
yy Make sure of the condition of this unit and the
connection in the cases below when using LG
Sound Sync.
-- Turned off the unit.
-- Changing the function to the others.
-- Disconnecting the wireless connection
caused by interference or a distance.
yy The amount of time to turn off this unit is
different depending on your TV.
yy Details of TV setting menu vary depending on
the manufacturers or models of your TV.
yy If you connect LG Sound Sync when “Music
Flow Bluetooth“ app is connected, control
through the app is available.
yy If you turned off the unit directly by pressing
1/! (Power), LG Sound Sync will be
disconnected. To use this function again, you
should reconnect the TV and the unit.
yy If an LG TV is connected when using
Bluetooth, Bluetooth is disconnected and
the LG TV is connected.
yy If you try to change the function on using
the LG TV function, volume will be change
according to the LG TV volume level.
“PAIRED” appears on the display window for
about 3 seconds and then you can see “LG TV”
on the display window if connecting normally
between this unit and your TV.
3
Operating
yy You can also use the remote control of this
unit while using LG Sound Sync. If you use TV's
remote control again, the unit synchronizes
with the TV.
3. Set up the sound output of TV to listen to the
sound through this unit :
TV setting menu [ [Sound] [ [TV Sound
output] [ [LG Sound Sync (Wireless)]
28 Troubleshooting
Troubleshooting
Problem
Cause & Correction
yy Turn off the power of this unit and the connected external device
(TV, Woofer, DVD-player, Amplifier, etc.) and turn it on again.
The unit does not work
properly.
yy Disconnect the power cord of this unit and the connected external device
(TV, Woofer, DVD-player, Amplifier, etc.) and then try connecting again.
yy Previous setting may not be saved when device power is shut off.
No Power.
No sound.
4
yy The power cord is not plugged in.
Plug in the power cord.
yy Check whether electricity failed.
Check the condition by operating other electronic devices.
yy Check whether you select right function.
Press FUNCTION and check the selected function.
yy Check to see if the speakers are connected to the unit correctly.
yy An unplayable disc is inserted. Insert a playable disc.
Troubleshooting
The unit does not start
playback.
yy No disc is inserted. Insert a disc.
yy The disc is dirty. Clean the disc. (Refer to page 31)
yy The disc is inserted upside down.
Place the disc with the label or printed side facing upwards.
yy The antenna is positioned or connected poorly. Connect the antenna securely.
yy The signal strength of the radio station is too weak.
Tune to the station manually.
Radio stations cannot be
tuned in properly.
yy No stations have been preset or preset stations have been cleared.
(when being tuned by scanning preset channels)
Preset some radio stations, see page 23 for details.
yy The remote control is too far from the unit.
Operate the remote control within about 23 ft (7 m).
The remote control does yy There is an obstacle in the path of the remote control and the unit.
Remove the obstacle.
not work properly.
yy The batteries in the remote control are exhausted.
Replace the batteries with new ones.
yy Check whether your LG TV supports LG Sound Sync.
LG Sound Sync does not
work.
yy Check connection of LG Sound Sync.
yy Check sound setting of your TV and this unit.
Appendix 29
Main unit
General
Power requirements
Refer to the main label.
Refer to the main label.
Power consumption
Networked standby : 0.5 W
(If all network ports are activated.)
Dimensions (W x H x D)
Approx. 230 mm x 125 mm x 236 mm
Net Weight
Approx. 2.1 kg
Operating temperature
5 °C to 35 °C
Operating humidity
5 % to 90 %
Inputs
Portable in (PORT. IN)
0.4 Vrms (3.5 mm stereo jack) x 1
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier (RMS Output power)
100 W
Front
50 W (6 Ω at 1 kHz, 10 % THD)
System
Frequency response
80 to 20,000 Hz
Signal-to-noise ratio
80 dB
Dynamic range
75 dB
Bus Power Supply (USB)
5 V 0 500 mA
5
Appendix
Total
30 Appendix
Speakers
Front
Type
Impedance
2 Way 2 Speaker
6Ω
Rated Input Power
50 W
Max. Input Power
100 W
Dimensions (W x H x D)
Approx. 150 mm x 250 mm x 140 mm
Net Weight
Approx. 1.52 kg
yy Design and specifications are subject to change without notice.
5
Appendix
Appendix 31
Maintenance
Handling the Unit
Notes on Discs
Handling Discs
Never stick paper or tape on the disc.
When shipping the unit
Storing Discs
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally
packed at the factory.
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Keeping the exterior surfaces clean
Cleaning Discs
Do not use volatile liquids such as insecticide spray
near the unit.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for old vinyl records.
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
Trademarks and
Licenses
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzine, or thinner,
as these might damage the surface of the unit.
The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn,
the picture quality could be diminished. For details,
please contact your nearest authorized service
center.
Bluetooth wireless technology is a system which
allows radio contact between electronic.
Connecting individual devices under Bluetooth
wireless technology does not incur any charges. A
mobile phone with Bluetooth wireless technology
can be operated via the Cascade if the connection
was made via Bluetooth wireless technology.
The Bluetooth word mark and logos are owned
by the Bluetooth SIG, Inc. and any use of such
marks by LG Electronics is under license.
Other trademarks and trade names are those of
their respective owners.
Appendix
Maintaining the Unit
5
Download PDF

advertising