LG | MCD112-A1U | LG MCD112-A1U Owner’s Manual

LGESA_MCD112-212_ENG_MFL40387034
ENGLISH
MODEL : MCD112B
MCD212B
There is so much your Hi-Fi system can do
Record from a CD,
AUX, USB or radio
to cassette
Go to pages 8
Contents
Setting up
About Player
About Remote control
Listening to CDs
Connecting your portable USB player
- OPTIONAL
Listening to the radio
Listen to cassette tapes
Recording
USER EQ
Setting the Clock
Use your player as an alarm clock
About MP3/WMA
Safety Precaution
Troubleshooting
Specifications
3
4
5
6
6
7
7
8
8
8
9
9
10
11
11
Lull me to sleep
and wake me up
Go to page 9
Before connecting, operating or adjusting this product, please read this instruction booklet
carefully and completely.
2
MINI Hi-Fi SYSTEM ] USER GUIDE
Play CDs and
cassettes
Go to pages 6 & 7
Setting up
1 Connect the speaker cables to the player
Cables from the left-hand speaker connect to the terminal marked L
(left) + (plus) and - (minus). Cables from the right-hand speaker are
connected to the terminal marked R (right) + (plus) and - (minus).
To connect the cable to the player, press each of the four square
plastic finger pads on the rear of the player. The connector will open
ready to receive a cable.
Put the batteries in the remote
control
Make sure that the + (plus) and
- (minus) on the batteries match those
on the remote control.
2 Fit the AM loop aerial to its stand
Connect the AM loop aerial to the player.
3 Connect the FM aerial
The reception will be at its best when the two loose
ends of the aerial are in a straight line and horizontal.
4 Plug the power plug into a wall socket
MINI Hi-Fi SYSTEM ] USER GUIDE
3
About Player
POWER
You can set up the unit into an economic
power save mode. In the power-on status,
press and hold 1/] (POWER) for about 3
seconds. To cancel power save mode, press
1/] (POWER).
ST./MONO
Press ST./MONO. This will change the tuner
from stereo to mono and usually improve the
reception.
MP3 OPT. (MP3 Optimizer)
This function is optimized for compressible
MP3 files so that it improves the bass sound.
DEMO
Press DEMO in power off state to demonstrate the function on display window. To cancel it, press 1 /]] or DEMO again.
Headphone jack
Connect a headphone plug ( 3,5 mm) into the
jack to listen to the sound through headphones (not supplied).
4
MINI Hi-Fi SYSTEM ] USER GUIDE
CD tray
XTS - PRO
The function creates the optimum sound for
you to play of the original sound. Each time
you press XTS - PRO, “XTS -- PRO ON” or
“XTS -- PRO OFF” is displayed in turn. (The
XTS Pro function will not be operated when a
headphone has been connected.)
D.SKIP
If more than one portable USB player is connected to the system at the same time, press
D.SKIP to select one of them.
AUX
You can connect many other types of audio
or audio visual device to the system via the
auxiliary sockets (AUX IN) on the back of the
player.
VOLUME
Control the volume when using any function.
USB connector - OPTIONAL
Connect a remote USB compatible player
here.
About Remote control
Search for a folder of MP3/WMA files
When a CD containing MP3/WMA files in
several folders is being played, press
PRESET/FOLDER to select the folder you
want to play.
Fall asleep while listening to your player
Firstly, start a radio station or music. Press
SLEEP on the remote one or more times to
select a delay of between 10 and 180 minutes, after which the player will turn off.
Use when playing a CD
Listen to your tracks again and again
Press REPEAT once to repeat the track currently playing. Press REPEAT twice to repeat
the whole CD, or if you’re listening to the
whole folder of MP3/WMA CD . The display
will show what is being repeated.
Use when playing a cassette tape
Sound quality adjustment
You can select a desired sound mode by
using EQ.
Play any track on a CD
Press the corresponding number buttons on
the remote control.
Temporarily stop the sound
Press the button again to return to the sound.
To change the functions
Change the functions between FM, AM, CD,
AUX, USB or TAPE
Dimm the display light
For storing radio stations
If you have saved radio stations using PROGRAM/MEMO, you can scroll through them
and select one (see Listening to the radio).
eXtreme Dynamic Sound System
Reinforce the treble, bass and surround
sound effect. XDSS ON will show in the display. Press again for XDSS OFF.
RANDOM
Press RANDOM, play tracks/files you can in
a random order or cancel it.
See information about your music
MP3/WMA files often come with tags. The tag
gives the Title, Artist or Album. Press INFO
while a file is playing to see this information.
If there are no tags, “NO ID3 TAG” or “NO
WMA TAG” will show.
MINI Hi-Fi SYSTEM ] USER GUIDE
5
Listening to CDs
ON PLAYER
1. Open the CD drawer:
2. Select the CD tray :
3. Insert the CD :
Label facing up.
4. Close the CD drawer:
The display will show the total
number of tracks (files).
5. Select the CD function:
6. Start the CD playing:
7. To stop a CD playing:
Z OP./CL.
D.SKIP
ON REMOTE
D.SKIP
Connecting your portable
USB player - OPTIONAL
The advantage of connecting your portable USB player
through the system’s USB port is that the portable device
can be controlled from the system. Connect the portable
player to the system using a USB cable (not supplied).
Z OP./CL.
CD
FUNCTION
B
x STOP
B/[]
x (CD STOP)
Listening to CDs - more you can do
Pause or restart a CD
Press CD[] on the front panel or B/[] on the remote control during playback.
Press this button again to resume play.
Search for a section within a track
Hold .bb/BB> during playback, then release at the point you want.
(This function is only available for Audio CD’s.)
Skip to another track
1. Press:
2. The display will show CHECKING, followed by the number
of files displayed.
3. Press:
4. Alternatively a numbered
track can be played by using
the numbers on the remote
control.
5. Before disconnecting the
portable USB player, change
to any other function by pressing:
6. Remove the USB cable.
ON PLAYER
ON REMOTE
USB
USB
B
B/[]
CD, TUNER,
TAPE or AUX
FUNCTION
Press .bb/BB> on either the player or the remote control.
Listen to your tracks in any order
Up to 20 tracks on a CD can be listened to in the order of your choice.
Insert a CD and wait for it to be read. Press PROGRAM/MEMO, then use
.bb/BB> to select the track. Press PROGRAM/MEMO again to
save and select the next track. Press B or B/[]. To clear your selection,
press STOP, PROGRAM/MEMO, STOP.
NOTE : You can choose a desired CD by using D.SKIP.
6
MINI Hi-Fi SYSTEM ] USER GUIDE
NOTE : Some portable devices are not compatible with this system.
Listening to the radio
Make sure both the FM and AM aerials are connected.
Choose a ‘preset number’ for a radio station
When storing a radio station, the preset number can be chosen. When the
player automatically shows a preset number press PRESET/FOLDER then.
Press PROGRAM/MEMO to save the number.
Delete all the saved stations
1. Select either AM or FM:
2. Select the radio station:
3. To ‘save’ a radio station:
A preset number will show in
the display.
4. To select a ‘saved’ station:
Up to 50 radio stations can be
saved.
5. To confirm press:
ON PLAYER
ON REMOTE
TUNER
TUNING (-)
or TUNING (+)
FUNCTION
TUN-/ TUN+
PROGRAM/MEMO
PRESET(-)
or
PRESET(+)
PRESET/FOLDER
PROGRAM/MEMO
Listening to the radio - more you can do
Press and hold PROGRAMME/MEMO for two seconds. “ERASE ALL”
shows. Press PROGRAMME/MEMO to erase all the saved stations.
Listen to cassette tapes
ON PLAYER
ON REMOTE
TAPE
FUNCTION
B
x STOP
B
x (TAPE STOP)
1. Open the tape door :
2. Insert the tape :
3. Close the tape door :
4. Select the TAPE function :
5. Start the tape playing :
6. To stop a tape playing:
See information about your radio stations - OPTIONAL
The FM tuner is supplied with the Radio Data System (RDS) facility. This
shows the letters RDS on the display, plus information about the radio station being listened to. Press RDS several times to view the information.
PTY - Programme Type, such as News, Sport, Jazz Music.
RT - Radio Text, the name of the radio station.
CT - Time Control, the time at the location of the radio station.
PS - Programme Service name, the name of channel.
You can search the radio stations by programme type by pressing RDS.
The display will show the last PTY in use. Press PRESET(-) / PRESET(+)
one or more times to select your preferred programme type. Press and
hold TUNING (-) / TUNING (+). The tuner will search automatically. When a
station is found the search will stop.
Listen to cassette tapes - more you can do
To Play Fast backward or Forward
After pressing bb/BB on the remote control or .bb/BB> on the
front panel during playback, or stop, press B at a point you want.
Dubbing
This function shows how to record from tape to tape. Press TAPE (or
FUNCTION) to select tape function.
• TAPE 1 - Insert a playback tape to dub.
• TAPE 2 - Insert a blank tape.
Press DUBB as shown below. To stop dubbing, press x.
Look for radio stations automatically
Press TUNING (-) / TUNING (+) on the front panel for more than 0.5
second. Or press TUN.- / TUN.+ on the remote control for more than 0.5
second. The tuner will scan automatically and stop when it finds a radio
station.
MINI Hi-Fi SYSTEM ] USER GUIDE
7
Recording
USER EQ
Record from a CD, AUX, USB or radio to cassette
You can listen to music with the desired sound effect (BASS, MIDDLE
and TREBLE).
Wind the tape to the point recording starts.
Use only normal tapes.
ON PLAYER
1. Open the TAPE 2 door :
2. Insert a blank tape :
3. Close the TAPE 2 door :
4. Select a mode (FM, AM, CD,
USB or AUX) in which you
want to record :
- Start playing the source you
want to record
5. Puts the unit in standby
more for recording
6. Start the Recording :
7. To stop a Recording :
ON REMOTE
Z PUSH EJECT
CD, TUNER,
USB, TAPE or
AUX
FUNCTION
REC
z/[]
REC
z/[]
x
x STOP
1. Select a “USER EQ”:
2. When “USER EQ” is
displayed, press :
3. Select the sound effect you
want among BASS, MIDDLE
or TREBLE :
4. Adjust sound level
(MIN, -4 to +4, MAX) :
5. Repeat the steps from 3 to 4
to set other sound effect :
6. Press :
ON PLAYER
ON REMOTE
EQ.
SET
EQ
PRESET (-)
or
PRESET (+)
.bb/BB>
SET
Setting the Clock
CD to Tape Synchronized Recording
The CD synchro recording function dubs a complete CD and
programmed titles automatically into a cassette.
1. Select the CD function :
2. Start the Recording :
The synchronized recording is
started automatically after
about 7 seconds
3. To stop a Recording :
8
ON PLAYER
ON REMOTE
CD
CD SYNC.
FUNCTION
x STOP
MINI Hi-Fi SYSTEM ] USER GUIDE
ON PLAYER
1. Press for at least 2 seconds:
2. Choose from either:
AM 12:00 (for an am and pm display) or 0:00 (for
a 24 hour display).
3. Confirm your selection:
4. Select the hours:
5. Press:
6. Select the minutes:
7. Press:
CLOCK
.bb/BB>
SET
.bb/BB>
SET
.bb/BB>
SET
Use your player as an alarm clock
About MP3/WMA
Press and hold TIMER for two seconds. Each function, TUNER, CD, USB,
MP3/WMA Disc compatibility with this unit is limited as follows:
• Sampling Frequency
8 - 48 kHz (MP3), 32 - 48 kHz (WMA)
• Bit rate
8 - 320 kbps(MP3), 48 - 320 kbps (WMA)
• CD-R physical format should be “ISO 9660”
• If you record MP3/WMA files using the software which cannot create a
FILE SYSTEM, for example “Direct-CD” etc., it is impossible to playback
MP3 files. We recommend that you use “Easy-CD Creator”, which creates an ISO 9660 file system.
• File names should be named using 30 letters or less and must incorporate “.mp3”,“.wma” extension e.g. “********.MP3” or “********.WMA”
• Do not use special letters such as “/ : * ? “ < >”etc.
• Even if the total number of files on the disc has more than 1000, it will
only be shown up to 999.
TAPE flashes for two seconds. Press SET when the function you want to
be woken by is showing. If you choose TUNER, ‘PLAY’ and ‘REC’ flash,
PLAY and REC. Choose one of them.
If you choose TUNER and PLAY you will be shown the stations you have
saved as presets. Use TUNING (-) or TUNING (+) to select the station
you want, then press SET.
You will be shown the ON TIME display. This is where you set the time
you want the alarm to go off. Use TUNING (-) or TUNING (+) to change
the hours and minutes and SET to save. You will then be shown the OFF
TIME display. This is where you set the time you want the function to stop.
Use TUNING (-) or TUNING (+) to change the hours and minutes and
press SET to save.
Next you will be shown the volume (VOL) you want to be woken by.
Use TUNING (-) or TUNING (+) to change the volume and SET to save.
Switch the system off. The red (clock icon) shows that the alarm is set.
When the system is turned off you can check the time the alarm is set for
by pressing TIMER. You can also turn the alarm on and off by pressing
TIMER. To set the alarm to go off at a different time, switch the system on
and reprogramme following the same steps as initially.
MINI Hi-Fi SYSTEM ] USER GUIDE
9
Safety Precaution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of uninsulated dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instruction has been adhered to.
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain it for
future reference. Should the unit require maintenance, contact an authorized service center.
Use of controls, adjustments or the performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation
when open. DO NOT STARE INTO BEAM.
10
MINI Hi-Fi SYSTEM ] USER GUIDE
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects
filled with liquids, such as vases, should be placed on the apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional outlets or
branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire. Periodically examine the cord of your appliance,
and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the
point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Troubleshooting
Symptom
No power.
No sound.
The unit does not
start playback.
The remote
control does not
work properly.
Unable to record.
Specifications
Cause
Correction
• The power cord is disconnected.
• Plug the power cord into the wall
outlet securely.
• The power of the external source • Switch on the external source
equipment is turned off.
equipment.
• The speaker cable is connected
• Set the speaker cable to the corto a wrong position.
rect position, then turn on the unit
again by pressing POWER.
• An unplayable disc is inserted.
• Insert a playable disc.
• The disc is placed upside down.
• Place the disc with the playback
side down.
• The disc is not placed within the
• Place the disc on the disc tray
guide.
correctly inside the guide.
• The disc is dirty.
• Clean the disc.
• The remote control is not pointed • Point the remote control at the
at the remote sensor of the unit.
remote sensor of the unit.
• The remote control is too far from • Operate the remote control within
the unit.
about 23 ft (7 m).
• There is an obstacle in the path
• Remove the obstacle.
of the remote control and the unit.
• The batteries in the remote con• Replace the batteries with new
trol are exhausted.
ones.
• Record protect tabs are removed. • Cover holes on back edge of tape
with tap.
General
Power supply
Power consumption
Net Weight
Refer to main label.
Refer to main label.
5.57 kg (MCD212B Model)
5.36 kg (MCD112B Model)
External dimensions (WxHxD) 270 x 310 x 390 mm
Operating temperature
5 oC to 35 oC
Operating humidity
5% to 85 %
Tuner
FM Tuning Range
AM Tuning Range
Amplifier
Output Power
87.5 - 108.0 MHz or 65 - 74 MHz,
87.5 - 108.0 MHz
522 - 1620 kHz or 520 - 1720 kHz
T.H.D
Frequency Response
Signal-to-noise ratio
100W + 100 W (MCD212B Model)
50W + 50 W (MCD112B Model)
0.5 %
40 - 20000 Hz
75 dB
CD
Frequency response
Signal-to-noise ratio
Dynamic range
40 - 20000 Hz
75 dB
75 dB
Speakers
MCS212F Type
Impedance
Rated Input Power
Max. Input Power
Net Dimensions (WxHxD)
Net Weight (1EA)
MCS112F Type
Impedance
Rated Input Power
Max. Input Power
Net Dimensions (WxHxD)
Net Weight (1EA)
Bass Reflex 2 Way 2 Speaker
4Ω
100 W
200 W
220 x 326 x 272 mm
3.25 kg
Bass Reflex 2 Way 2 Speaker
4Ω
50 W
100 W
200 x 326 x 228 mm
2.92 kg
Designs and specifications are subject to change without notice.
MINI Hi-Fi SYSTEM ] USER GUIDE
11
P/NO : MFL40387034
Download PDF

advertising