LG | WFL-9KG | LG WFL-9KG Owner’s Manual

Remove Packaging
• The appliance is fitted with transit bolts to prevent internal
damage during transport. Be careful, heavy load!
• Packing and all transit bolts must be removed before using
the washing machine.
• When unpacking the base, be sure to remove the additional
packing support in the middle of the base packing.
original packing for future move.
i Store
Dispose of packing material according to local regulations.
Transit bolts
Schraubenschlüssel
1
To prevent internal damage during transport, the
special 4 bolts are locked.
If they are not removed, it
may cause heavy vibration, noise and machine to
malfunction.
2
Remove the 4 bolts
along with the rubber
bungs by slightly
twisting the bung.
Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the
washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION about positioning the appliance
Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
• Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
• If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
• The washing machine must not be installed in rooms where the temperature may drop below 0°C.
• Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.
• Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
BS Plug Safety Details (For U.K. User)
E
Fuse
This appliance must be earthed As the colours of the wires in the mains lead
of this apparatus may not correspond with the coloured markings identifying
Cord
grip
the terminals in your plug, proceed as follows: The green and yellow wire must
be connected to the terminal in the plug marked E or by the earth symbol or
coloured green or green and yellow. The wire coloured blue must be connected
to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal
marked with the letter L or coloured red. If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
5
L
N
CAUTION about the power cord
Connecting water supply hose
The hose supplied with the machine must be used. Old hoses may not be reused
3
4
Unscrew the 4 bolts
3. Die 4 Schrauben
lösen und die
using the spanner
supplied. etwas drehen, um
Gummipfropfen
sie
zusammen mit den Schrauben abzunehmen.
Die 4 Schrauben und den Schraubenschlüssel
für späteren Gebrauch aufbewahren.
Close the holes with
the caps supplied.
• Die Transportsicherungsschrauben müssen vor
and the spanner for the future use. Refit transit bolts before transporting the appliance.
i Keep the 4 bolts
3
jedem Transport des Geräts wieder angebracht
werden.
• The drain hose should not be placed higher than 100 cm above the floor.
Don’t strip or crossthread when connecting inlet hose to the valve.
• Proper securing of the drain hose will protect the floor from damage due to any water leakage.
If the water supply pressure is more than 1000kPa, a decompression
device should be installed.
• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.
• Make sure the connection to taps is tight enough.
Requirements for installation site
7
Level adjustment
• Proper level-adjustment of the washing machine prevents excessive noise and vibration.
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
• Make sure that there is no kink on the hose and
that it is not crushed.
Level floor: Permissible floor gradient under entire washing machine
is 1˚ .
When your washing machine has two valves:
• The inlet hose with the red connector is for the hot
water tap.
Power socket: Must be
5 within 100 cm of either side of location of
washing machine. Do not overload the socket with more than one
appliance.
• If the washing machine has two valves, power
saving is achieved through using hot valve.
connection water leaks from the hose, repeat the same steps. Use the most conventional
i Iftypeafterof completing
tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting
the tap into the adaptor.
We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance
concerned, without any additional outlets or branch circuits. Check the specifications of this owner‘s manual. Do not overload
wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or
cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord
of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated
device in the mains supply.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain (gully)
in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young
children becoming trapped inside. Packaging material (e.g. plastic film, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging well away from children.
CAUTION about the floor surface
• Periodically check the condition of the hose and
replace the hose if necessary.
4. Die Schraubenbohrungen mit den
beiliegenden Kappen verschließen.
Additional Clearance: For wall, floor and door space is needed.
(10cm: rear / 2cm:right & left side). Do not place or store laundry products on top of the washing machine at any times. They can damage
the finish or controls of the machine.
Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)
• Two rubber seals are supplied with the water inlet
hoses. They are used for preventing water leaks.
Safety instructions for use
Safety instuctions for the installation
Installation of drain hose
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person
to prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service centre.
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.
Green and
Yellow (Earth)
Brown(Live)
Blue(Neutral)
2
6
Electrical connection
4
60 - 100 cm
1
Adjustable feet
• If the floor is uneven, adjust feet as required.
(Do not insert pieces of wood etc. under the
feet). Make sure that all four feet are stable
and resting on the floor. Then check that
the appliance is perfectly level. (Use a spirit
level).
•
•
•
•
•
•
•
The installation surface must be clean, dry and level.
Install washing machine on a flat hard floor.
Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
The washing machine must be perfectly level and firmly in position.
It must not “see-saw” across corners under load.
The installation surface must be clean, free from floor wax and other lubricant coatings.
Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
@
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with cold
drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper and
may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualified fitter or technician.
• Have electrical connections done by a qualified electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect
by pulling the power cord. Never touch the plug with wet fingers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances
(such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been
used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain in
the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly inflammable gas.
Such materials may cause fire or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement parts.
• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to protect children.
• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fire.
• The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning.
arantiebedingungen
Disposal
Name of product
Front loading washing machine
Max. Watt
2100 W (Wash)
Power supply
220-240 V~, 50 Hz
Wash capacity
9 kg
Size WxDxH mm:
600 x 640 x 850
Water consumption
63 l (7 l / kg)
Weight
65 kg
Permissible water pressure 1.0-10 bar (100-1000kPa)
Troubleshooting
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating
instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these
operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it into operation.
G
Technical Specification
N
• When this crossed-out wheeled bin symbol is attached to a product it means the product is covered
Entsorgung von Altgerätenby European Directive 2002/96/EC.
1. Wenn dieses Symbol eines durchgestrichenen Abfalleimers
•aufAll
electrical
electronic
products
should
einem
Produkt and
angebracht
ist, unterliegt
dieses
Produktbe disposed of separately from municipal waste stream
dervia
europäischen
Richtlinie
2002/96/EC.
designated
collection
facilities
appointed
by the government or the local authorities.
2. Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom
über dafür
staatlich of
vorgesehenen
Stellen entsorgt
•Hausmüll
The correct
disposal
your old appliance
will help prevent potential adverse consequences for the
werden.
and human
health.
3. Mitenvironment
der ordnungsgemäßen
Entsorgung
des alten Geräts
Sie Umweltschäden
und eine about
Gefährdung
der of your old appliance, please contact your city office,
•vermeiden
For
more
detailed
information
disposal
persönlichen Gesundheit.
4. Weitere
zur Entsorgung
altenwhere
Geräts you purchased the product.
wasteInformationen
disposal service
or thedes
shop
erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt
oder in dem Geschäft, wo Sie das Produkt erworben haben.
• Water supply is not adequate in
area
• Water supply taps are not
completely open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are
clogged.
Check another tap in the house.
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information,
please refer to “Cleaning the drain pump filter”
• Load is too small.
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning
• Load is out of balance.
• The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both robe,
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
Owner‘s Manual
F1403FD(1~9)
etc.), this system may stop spinning or even
interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
• Is the door opened or not
completely closed?
Close the door completely.
If “
”is not released, call for service.
Unplug the power plug and call for service.
• Water overfills due to the faulty water
valve.
• Water level sensor has malfunctioned.
Close the water tap.
Unplug the power plug.
Call for service.
• Over load in motor.
• The washer experienced a power failure.
Restart the cycle.
Rattling and clanking noise
Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound
Heavy wash loads may produce a thumping sound. This is usually normal.
Vibrating noise
Have all transit bolts and packing been removed?
Water leaks.
Check and tighten hose connections. Unclog drain pipe.
Contact plumber if necessary.
Excessive suds
Too much detergent or unsuitable detergent.
Washing machine does not start
Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin
Check that the door is firmly shut.
Door does not open
Once started, the door can not be opened for safety reasons.
Wait one or two minutes before opening the door to allow the electric
locking mechanism time to release.
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.
For the U.K. customer
CUSTOMER SERVICES Tel. : +44-(0) 844 847 LGLG(5454) Fax. : +44-(0) 844 847 1413
LGEUK SERVICE WEB-SITE : http://www.lge.co.uk
P/No. :MFL41480109
Preparation
Washing symbols
CHECKING THE MACHINE
Never use a defective machine! In case of any
failure, first unplug the machine and turn off the
water tap.
Do not
tumble dry
Dry flat
Do not wash
Hot ironing
Hang to dry
Do not bleach
Main Wash
For very dirty clothes fill 1/4 of the
portion of detergent in here and
select a prewashing programm
Program
Cotton
- empty all pockets
- remove all metal parts
- place the delicate textiles into the laundry net
- close zippers
Cotton
Quick
Synthetic
Baby Care
Duvet
Delicate
Wool
Quick 30
Softener
Do not exceed the MAX-Level.
Highly densed softeners are to
be diluted with some water.
C
Pre Wash
For normal dirty clothes use a small
amount of detergent. Don't pre wash.
Mount the level plate to use fluid detergents.
Fabric Type
Color fast garments (shirts,
nightdresses, pajamas...)and
lightly soiled white cotton
(underwear)
Lightly soiled clothing and
small loads
Polyamide, Acrylic, Polyester
Lightly soiled baby wear
Delicate laundry easily
damaged
“Hand wash” marked delicate
and wool laundry
Water Temp.
(Option)
60°C
(Cold, 30°C,
40°C, 95°C)
40°C (Cold,
30°C, 60°C)
Option
- Time Delay
- Intensive
- Soak
- Pre Wash
- Crease Care
- Rinse+Spin
- Medic Rinse
60°C
(40°C, 95°C)
40°C
(Cold, 30°C)
30°C
(Cold, 40°C)
Machine washable woolens
with pure new wool only
40°C
(Cold, 30°C)
Colored laundry which is lightly
soiled fast
30°C
(Cold, 40°C)
Maximum Load
Fill the drum
Check the folds of the flexible gasket (grey) and remove any small articles, if any. .
Check inside of the drum and remove any left in items for next wash cycle. .
Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages .
Fill detergent
Refer to the
written information
on the detergent's packing
2
Less than 7kg
Control panel
Dispenser
drawer
Favorite
Program Cycle
Power button
Start / Pause
Options
Temperature
Rinse
B
3
Drum
A
Turn off tap
- close water supply
- clean the machine
- unplug machine
C
Turn the machine ON
by pressing the Power button
Cover cap
Additional Steps
- Turn the machine off
- leave door open to
allow drum to dry
Select a
Program
Select the
Spinning speed
Less than 2.0kg
Child Lock
Cleaning and Maintenance
Select this function to lock the buttons on the control panel and to prevent tampering.
6 3 sec.
6 3 sec.
Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric shock.
Change to the desired program, whilst in child lock mode:
6 3 sec.
Cleaning the water inlet filter
2
1
To activate:
press and hold
the Option buttons
simultaneously
To deactivate:
press and hold
the Option buttons
simultaneously
Press and hold
the Option buttons
simultaneously
Press
Start/Pause
Select the desired
program
press
Start/Pause
1
Turn off the water
tap
Tub Clean
Unscrew the water
inlet hose
4
Pull out the water
inlet filter
5
Clean the filter using
a hard bristle brush
Tighten up the inlet
hose
Cleaning the drain pump filter
6 3 sec.
1
2
3
4
5
1
Empty the drum
completly and close
the door
Add anti-limescale
(Calgon) to the main
wash compartment.
Close the disp. drawer
Power ON with
Then press and
hold Rinse and
Temp. button
Press the
Start/Pause
button to start Tub
Clean process
After the cycle is
complete, leave the
door open to dry
2
3
Open the lower cover Unplug the drain plug.
cap. Drain plug to
Then open the filter
pull out the hose
by turning to the left
Medic Rinse
Available in the Cotton, Cotton Quick, Synthetic and Baby Care programs.
Medic Rinse is set by default in the Baby Care program.
The respective temperature indicator will light up.
3
TUB CLEAN is special cycle to clean the inside of the washing machine.
A higher water level is used in this cyle at higher spin speed. Perform this cycle regularly.
Intensive
For best results or for cleaner rinsing, select the “Medic Rinse” option.
2
4
Remove any
extraneous matter
from the pump filter
5
After cleaning, turn
the pump filter and
insert the drain plug
Close the lower
cover cap
Cleaning the dispenser drawer
Beep on / off
The Beep on/off function can be set by pressing and
holding the Option and Rinse button simultaneously.
The Beep on/off function can be set at any time and it is
automatically cancelled in the event of a power cut.
The Beep on/off function also works when power is off.
1
2
Pull out the
dispenser drawer
3
Clean the dispenser
drawer under flowing water
Cleaning in general
tt
4
Clean inside the
recess with an old
toothbrush
Insert the dispenser
drawer
5 Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry.
Important: Do not use methylated spirits, solvents or similar products.
un
til
w
as
hi
ng
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are
washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0708.
Notes
Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care.
Remove laundry
- open the door
- remove the laundry
Select an Option
Pre Wash / Soak / Crease Care / Rinse+Spin
Select Rinse mode
and Washing temperature
- Favorite program allows you to store a customized wash cycle for future use.
- To make a Favorite program:
(1) Select a cycle.
(2) Select
The course, washing method, number of rinses, spin speed, water temperature etc.
(3) Press and hold Favorite program button 3 econds (2 beep sounds).
The Favorite program is now stored for future use.
To reuse the program, select Favorite program and press Start/Pause.
If the laundry is heavily soiled “Intensive”option is effective.
- By selecting the Intensive option, the washing duration may be extended,
depending on the program selected.
- To use this option, press the intensive button once before the wash program is started.
Less than 4.5kg
Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufacture’s care label or instructions when washing.
Intensive: If the laundry is heavily soiled “Intensive” option is effective.
Set program at “Cotton 60°C + Intensive” option for test in accordance or in conformity with EN60456 and IEC60456.
Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in the Cotton, Cotton Quick, Synthetic and Baby Care program.
Crease Care: If you want to prevent creasing, select Crease Care option.
Medic Rinse: For best results or for cleaner rinsing, you can choose Medic Rinse option. Medic Rinse is set by default in the Baby Care program.
Warning: Keep all washing powder and detergents away from children. Danger of poisoning
How to set “Time Delay”
- Press Power button.
- Turn the Program dial to select the program you require.
- Press Time Delay button and set time required.
- Press the Start/Pause button.
Rating
1 king size (9 Tog)
- Time Delay
- Intensive
- Crease Care
- Rinse+Spin
Spinning cycle
Time Delay
ai
ECOLOGICAL WASHING
- make use of the max. washing quantity
- do not “pre wash” if possible
- use short program if possible
Handy to bleach
Display
Additional programs
W
DRUM CARE
- remove extraneous objects
- leave door open to dry the drum
- check the rubber seals regularly
B
Cotton bedding with filling duvet,
pillow, blanket, sofa cover with
light filling
Hand Wash
WATER TREATMENT
- with hardness III water
- use water softening agent
Drip dry
Additional programs
1
Setting “Time Delay” determines when machine stops.
Washing program table
DOING LAUNDRY AND USING MACHINE
WITH CARE
LAUNDRY WITH DIFFERENT AMOUNTS OF
SOILING
- wash new textiles separately
lightly
- do not prewash
- pretreat dirty spots
heavily
- pre wash
Do not iron
Dispenser drawer
A
INSERT PLUS INTO THE MAINS SOCKET
Never touch the plug with wet hands!
Never remove the plug from the
socket by pulling on the cord.
Medium hot
ironing
Luke warm ironing
WATER CONNECTION
Turn on the water tap
HANG UP WASTE WATER HOSE
Hose elbow connection e.g. attach to water tap
Washing
temperature
Sort the laundry
note washing instruction symbols Degree of soiling Type of textile / colour -
4 additional programs
Time Delay / Favorite / Intensive / Medic Rinse
is
Press Start / Pause
to start the washing process
f in
ish
ed
Exterior
Proper care of your washing machine can extend its service life. The
outside of the machine can be cleaned with warm water and a neutral
non-abrasive household detergent. Immediately wipe off any spillage.
Wipe with damp cloth. Avoid striking the surface with sharp objects. Never
hose down the machine!
Interior
Dry around the washing machine door
opening, flexible gasket and door glass.
Run washing machine through a complete
cycle using hot water. Repeat process if
necessary.
Download PDF