LG | DC6121GSA | Owner's Manual | LG DC6121GSA Owner’s Manual

LG DC6121GSA Owner’s Manual
IT
Model Numbers
GB
Instruction Manual
FR
Manuel d'Instructions
DE
Bedienungsanleitung
NL
Gebruiksaanwijzing
DC9121GSA
DC6121GSA
Part NO. 383EW5N001M
Dear
Customer,
If you follow the recommendations
contained in this Instruction Manual,
appliance will give you constant
high performance and will remain
your
efficient for many years to
come.
CONTENTS
RECOMMENDATIONS AND SUGGESTIONS
3
CHARACTERISTICS
4
INSTALLATION
6
USE
9
MAINTENANCE
10
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
The manufacturer will not be held liable for any
incorrect or improper installation.
The minimum
hood is 650
safety
damages resulting
distance between the cooker
top and the
from
extractor
mm.
Check that the mains
voltage corresponds to that indicated on the rating
plate fixed to the inside of the hood.
For Class I appliances, check that the domestic power supply guarantees
adequate earthing.
Connect the extractor to the exhaust flue through a pipe of minimum diameter
120 mm. The route of the flue must be as short as possible.
Do not connect the extractor hood to exhaust ducts carrying combustion
fumes (boilers, fireplaces, etc.).
If the extractor is used in conjunction with non-electrical appliances (e.g.
gas burning appliances), a sufficient degree of aeration must be guaranteed
in the
in order to
room
must have
an
prevent the backflow of exhaust gas. The kitchen
opening communicating directly with the open
air in order to
guarantee the entry of clean air.
Installation of the extractor hood
over a solid-fuel burner(coal, wood,etc.)
potential fire hazard (e.g. due to flying sparks) is
only permitted if the burner is equipped with an enclosed, non-removable
cover and all country-specific regulations are observed. This restriction
dose not apply to gas cookers and gas hobs.
Regulations concerning the discharge of air have to be fulfilled.
which could constitute
a
USE
The extractor hood has been
designed exclusively
for household
use
to
eliminate kitchen smells.
Never use the hood for purposes other than for which it has been
designed.
high naked flames under the hood when it is in operation.
Adjust the flame intensity to direct it onto the bottom of the pan only, making
sure that it does not engulf the sides.
Deep fat fryers must be continuously monitored during use: overheated oil
Never leave
can
burst into flames.
The hood should not be used
Do not
use
the
appliance
by children or persons
damaged in any way.
Never operate the extractor hood without
Do not flambe food
not instructed in its correct
use.
if it is
directly
a
grease filter.
under the extractor hood.
MAINTENANCE
Switch off
or
unplug
the
appliance
from the mains
supply
before
carrying
out any
maintenance work.
Clean and/or
replace the Filters after the specified time period.
using a damp cloth and a neutral liquid detergent.
Defective bulbs should be replaced immediately to prevent the remaining bulbs from
overloading.
There is a fire risk if cleaning is not carried out in accordance with the instructions.
Clean the hood
GB
3
CHARACTERISTICS
Dimensions
GB
4
Components
Ref.
Q.ty
Product
Components
Body, complete with: Controls, Light,
1
1
Hood
2
1
2.1
1
Telescopic Chimney comprising:
Upper Section
2.2
1
Lower Section
9
1
Reducer
10
1
Damper
14.1
2
Air Outlet Connection Extension
15
1
Air Outlet Connection
Blower, Filters
GB
Flange ø
150-120
mm
Ref.
Q.ty
7.2.1
2
Installation
7.3
1
11
6
Components
Upper Chimney Section Fixing
Air Outlet Connection Support
Wall Plugs
12a
6
Screws 4,2
x
44,4
12c
6
Screws 2,9
x
9,5
1
Documentation
Brackets
5
INSTALLATION
Wall
Wall
bracket
fixing
marking:
vertical line
on the supporting wall up to the
in which the hood will be installed.
Draw
a
of the
area
?
Draw
a
?
Place bracket 7.2.1
?
drilling and
horizontal line at 650
the centre
(notch)
on
mm
the wall
as
ceiling,
mm
Mark the wall at the centres of the holes in the bracket.
Place bracket 7.2.1
on
the wall
as
shown at X
practical,
ceiling
or
at the centre
upper limit
supplied), aligning
below the first bracket (X
(notch) with the vertical line.
=
Mark the wall at the centres of the holes in the bracket.
?
Mark
reference
from the
mm
the centre
?
a
as
aligning
with the vertical reference line.
?
chimney
high
above the hob.
shown about 1-2
?
section
or as
point as indicated at
116
mm
height of the upper
from the vertical reference line and 306
mm
above
the horizontal reference line.
?
?
Repeat
this
Drill ø 8
operation
mm
on
the other side.
holes at all the centre
?
Insert the wall
?
Fix the lower bracket 7.2.1
?
?
plugs
points
marked.
11 in the holes.
using
the 12a
screws
(4,2
x
44,4) supplied.
Fix the upper bracket 7.2.1 and the air outlet connection support 7.3
12a (4,2 x 44,4) supplied.
Insert the two
6
mm
GB
screws
12a
(4,2
x
together using
the 2
44,4) supplied in the hood body fixing holes, leaving
between the wall and the head of the
a
screws
gap of 5-
screw.
6
Mounting the hood body
?
Before
two
?
?
?
the hood
attaching
Vr located
screws
body, tighten the
the hood body
on
mounting points.
Hook the hood body onto the screws 12a
Fully tighten support screws 12a
Adjust screws Vr to level the hood body.
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When
pipe
installing the ducted version,
ø 150
?
To install the
?
To install
a
connect the hood to the
chimney using either a flexible or rigid
120 mm, the choice of which is left to the installer.
or
dumper 10
ø 120
mm
air exhaust connection,
insert the reducer
?
?
flange 9 on the dumper 10.
Fix the pipe in position using sufficient pipe
clamps (not supplied).
Remove any activated charcoal filters.
RECIRCULATION VERSION AIR OUTLET
?
Put connection 15
?
Insert the connection extension
into the connection support 7.3.
pieces laterally
14.1 in connection 15.
?
Make
sure
pieces
aligned
?
that the outlet of the extension
14.1 is
with the
horizontally and vertically
chimney outlets.
Connect the air outlet connection 15 to the
hood
pipe
body outlet using either a flexible or rigid
ø
150, the choice of which is left
to the
installer.
?
Ensure that the activated charcoal filters have
been inserted.
GB
7
ELECTRICAL CONNECTION
?
Connect the hood to the mains
switch
?
having
through
contact gap of at least 3
a
a
two-pole
mm.
Remove the grease filters (see paragraph Maintenance)
being sure that the connector of the feeding cable is
correctly inserted in the socket placed on the side of
the fan.
Flue assembly
Upper exhaust
Slightly widen
?
making
?
sure
that
they
are
well seated.
Secure the sides to the brackets
screws
?
flue
the two sides of the upper flue
and hook them behind the brackets 7.2.1,
Make
is
12c
sure
aligned
(2,9
x
using
the 4
9,5) supplied.
that the outlet of the extensions
with the
chimney
pieces
outlets.
Lower exhaust flue
?
Slightly widen the two sides of the flue and hook
them between the upper flue and the wall,
making sure that they are well seated.
?
Fix the lower part laterally to the hood body
using the 2 screws 12c (2,9 x 9,5) supplied.
GB
8
USE
Control Panel
The hood
can
be switched
on
pushing directly
onto the
requested speed
without
firstly having
to
select 0/1 button.
LED
L
0/1
T1
0/1 Motor
FUNCTIONS
Turns
Light
lighting
First
speed.
When
pressed
T2
Speed
on
Second
T3
Speed
on
Third
T4
Speed
Fixed
on
Flashing
Max.
on
and off.
for about 1 seconds the motor is switched off.
speed.
speed.
speed
Intensive
speed.
Suitable for the strongest cooking vapours and odours.
The function becomes active when the button is pushed
for about 2 seconds. After 10 minutes of
functioning it
automatically. This function can be interrupted
by means of pressing any of the buttons.
turns off
S1
Led
Fixed
on
Indicates that the Metal grease filters saturation alarm
triggered, and the filters need to be washed.
has been
The alarm is
check the
Flashing
triggered after 100 working hours. (Reset;
Maintenance-paragraph)
indicates that the activated charcoal odour filter
saturation alarm has been
triggered,
and the filter has to
be replaced; the metal grease filters must also be washed.
The activated charcoal odour filter is triggered after 200
working hours. (Activation
Maintenance-paragraph)
GB
and Reset; check the
9
MAINTENANCE
Grease filters
CLEANING METAL GREASE FILTERS
?Alarm
signal
reset
?
Switch off the
?
Press button T3 for at least 3
lights
and extractor motor.
seconds, until
the leds T1,T4 start to flash.
Cleaning
?
the filters
The filters
are
washable and must be cleaned
when the LED S1
lights up or at least every
operation, or more frequently for
particularly heavy usage.
Remove the filters one at a time by pushing them
towards the back of the group and pulling down
2 months of
?
at the
?
?
same
time.
Wash the filters, taking care not to bend them.
Allow them to dry before refitting.
When
refitting
the filters, make
on the outside.
sure
that the
handle is visible
GB
10
Activated charcoal filter (Recirculation version)
the alarm
Enabling/Disabling
?
In Recirculation version
a
signal
Hoods, the Filter saturation alarm
?
Turn the
?
Disconnect the Hood
be enabled
on
installation
or
at
and the suction Motor off.
the Main switch
the mains power
the side of the fan.
or
Lights
on
using
supply
?
Restore the connection
?
Release the button.
?
can
later date.
or
the
the connector of the
by pressing
All five LEDs
and
are
holding
turned
double-pole switch
feeding cable from
T1
on
Within 3 seconds press T1 until LEDs T1 and T4 flash in confirmation:
LED flashes twice
Activated charcoal filter saturation alarm ENABLED
?
?
-
LED flashes
once
-
Activated charcoal filter saturation alarm DISABLED
REPLACING THE ACTIVATED CHARCOAL FILTER
?
The filter is not washable and cannot be
regenerated.
replaced when S1 flashes or at least every
4 months. The alarm signal will only light up when the
It must be
extractor motor is switched
Alarm
on.
reset
signal
?
Switch off the
?
Press button
lights
and extractor motor.
T3 for at least 3
seconds, until
the leds start to flash.
Replacing
?
?
the Filter
Remove the metal grease filters
Remove the saturated activated carbon filter
by releasing
?
?
Fit the
new
Replace
the
filter
fixing hooks
by hooking it
into its
seating
the metal grease filters.
Lighting
LIGHT REPLACEMENT
20 W
?
one
?
?
?
halogen light.
Remove the snap-on lamp cover by levering it
from under the metal ring, supporting it with
hand.
Remove the halogen
lamp from the lamp holder
by pulling gently.
Replace the lamp with a new one of the same
type, making sure that you insert the two pins
properly into the housings on the lamp holder.
Replace the snap-on lamp cover.
When switched on, the
halogen
bulbs become very hot. Even for
after the bulbs have been switched off there is still
GB
a
some
time
risk of burns.
11
Dir. 89/336/CEE
73/23/CEE
93/68/CEE
436002375_03 050714
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising