LG | LCN427HV.ANWBEUS | LG LCN187HV.ANWBEUS Owner’s Manual

ENGLISH
FRANCAIS
ESPAÑOL
OWNER’S MANUAL
AIR CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
TYPE : Ceiling Cassette
*MFL67163912*
P/NO : MFL67163912
http://www.lghvac.com
www.lg.com
Air Conditioner Ownerʼs Manual
TABLE OF CONTENTS
A. Safety Precautions .......................3
B. Product Introduction....................6
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
C. Operating instructions.................9
D. Maintenance and Service ..........21
Serial #
You can find them on a label on the side of each unit.
Dealer's Name
Date Purchased
n Staple your receipt to this page in the event you need it
to prove date of purchase or for warranty issues.
READ THIS MANUAL
Inside you will find many helpful hints on how to use and
maintain your air conditioner properly. Just a little
preventive care on your part can save you a great deal
of time and money over the life of your air conditioner.
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call for
service at all.
PRECAUTION
• Contact the authorized service technician for repair or
maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• When the power cord is to be replaced, replacement
work shall be performed by authorized personnel only
using only genuine replacement parts.
• Installation work must be performed in accordance
with the National Electric Code by qualified and
authorized personnel only.
2 Air Conditioner
Safety Precautions
Safety Precautions
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage.
WARNING
Always ground the product.
• There is a risk of electric shock.
For electrical work, contact the dealer, seller,
a qualified electrician, or an Authorized
Service Center. Do not disassemble or repair
the product by yourself.
• There is risk of fire or electric shock.
Use the correctly rated breaker or fuse.
• There is risk of fire or electric shock.
Do not install the product on a defective
installation stand. Be sure that the
installation area does not deteriorate with
age.
• It may cause product to fall.
Be sure to check the refrigerant to the
used. Please read the label on the product.
Do not use a defective or underrated
circuit breaker. Use the correctly rated
breaker and fuse.
• There is risk of fire or electric shock .
Always ground the product as per the
wiring diagram. Do not connect the
ground wire to gas or water pipes
lightening rod or telephone ground wire.
• There is risk of fire or electric shock.
Do not modify or extend the power cable.
If the power cable or cord has scrathes or
skin peeled off or deteriorated then it
must be replaced.
• There is risk of fire or electric shock.
Never install the outdoor unit on a
moving base or a place from where it
can fall down.
• The falling outdoor unit can cause damage or
injury or even death of a person.
Don't use a power cord, a plug or a loose
socket which is damaged.
• Incorrect refrigerant used can prevent the
normal operation of the unit.
• Otherwise it may cause a fire or electrical
shock.
Do not place a heater or other heating
appliances near the power cable.
Do not allow water to run into electric
parts. Install the unit away from water
sources.
• There is risk of fire and electric shock.
• There is risk of fire, failure of the product, or
electric shock.
Do not use a multi consent. Always use
this appliance on a dedicated cicuit and
breaker.
• Otherwise it can cause electric shock or fire.
Install the panel and the cover of control
box securely.
• There is risk of fire or electric shock due to
dust , water etc.
For installation, removal or reinstall ,
always contact the dealer or an
Authorized Service Center.
• There is risk of fire, electric shock, explosion,
or injury.
When the product is soaked (flooded or
submerged) in water , contact an
Authorized Service Center for repair
before using it again.
• There is risk of fire or eletric shock.
Do not touch , operate, or repair the
product with wet hands. Hold the plug by
hand when taking out
• There is risk of electric shock or fire.
Do not store or use or even allow
flammable gas or combustibles near the
product.
• There is risk of fire.
Owner's Manual 3
ENGLISH
To prevent injury to the user or other people and property damage, the following instructions must be followed.
n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by
the following indications.
Safety Precautions
Indoor/outdoor wiring connections must
be secured tightly and the cable should
be routed properly so that there is no
force pulling the cable from the
connection terminals.
Safely dispose off the packing materials.
Like screws, nails, batteries, broken
things etc after installation or svc and
then tear away and thraw away the plastic
packaging bags.
Make sure to check that the power cable
plug is not dirty, loose or broken and
then only insert the plug completely.
• Improper or loose connections can cause
heat generation or fire.
• Children may play with them and cause
injury.
• Dirty, loose or broken power plug can
cause electric shock or fire.
In outdoor unit the step-up capacitor
supplies high voltage electricity to the
electrical components. Be sure to
discharge the capacitor completely
before conducting the repair work.
When installing the unit, use the
installation kit provided with the product.
Be sure to use only those parts which
are listed in the svc parts list. Never
attempt to modify the equipment.
• An charged capacitor can cause electrical
shock.
• Otherwise the unit may fall and cause severe
injury.
• The use of inappropriate parts can cause an
electrical shock, excessive heat generation or
fire.
Do not open the front grille of the product
during operation. (Do not touch the
electrostatic filter, if the unit is so equipped.)
If strange sounds, smell or smoke comes
from product.Immediately turn the breaker
off or disconnect the power supply cable.
Do not use the product in a tightly closed
space for a long time. Perform ventilation
regularly.
• Oxygen deficiency could occur and hence
harm your health.
• There is risk of physical injury, electric shock,
or product failure.
• There is risk of electric shock or fire.
Ventilate the product room from time to
time when operating it together with a
stove, or heating element etc.
Turn the main power off and unplug the
unit when cleaning or repairing the
product.
When the product is not to be used for a
long time, disconnect the power supply
plug or turn off the breaker.
• Oxygen deficiency can occur and hence harm
your health.
Take care to ensure that nobody
especially kids could step on or fall onto
the outdoor unit.
• This could result in personal injury and
product damage.
• There is risk of electric shock.
Take care to ensure that power cable
could not be pulled out or damaged
during operation.
• There is risk of fire or electric shock.
Do not plug or unplug the power supply plug to turn the unit
ON/OFF .
• There is risk of fire or electric shock.
• There is risk of product damage or failure, or
unintended operation.
Do not place ANYTHING on the power
cable.
• There is risk of fire or electric shock.
When flammable gas leaks, turn off the gas and open a window
for ventilation before turn the product on.
• Do not use the telephone or turn switches on or off. There is risk of
explosion or fire.
CAUTION
Two or more people must lift and
transport the product.
• Avoid personal injury.
Keep level even when installing the
product.
• To avoid vibration or noise.
4 Air Conditioner
Do not install the product where it will be
exposed to sea wind (salt spray) directly.
• It may cause corrosion on the product.
Do not install the product where the noise
or hot air from the outdoor unit could
damage or disturb the neighborhoods.
• It may cause a problem for your neighbors
and hence dispute.
Install the drain hose to ensure that the
condensed water is drained away properly.
• A bad connection may cause water leakage.
Always check for gas (refrigerant)
leakage after installation or repair of
product.
• Low refrigerant levels may cause failure of
product.
Safety Precautions
Do not use the product for special purposes,
such as preserving foods, works of art, etc. It
is a consumer air conditioner, not a precision
refrigeration system.
Do not touch the metal parts of the
product when removing the air filter.
• There is risk of personal injury.
Do not insert hands or other objects
through the air inlet or outlet while the
product is operating.
• There are sharp and moving parts that could
cause personal injury.
Do not tilt the unit when removing or
uninstalling it.
• The condensed water inside can spill .
Dismantling the unit, treatment of the
refrigerant oil and eventual parts should
be done in accordance with local and
national standards.
• It may cause product failure.
Do not step on or put anyting on the
product. (outdoor units)
• There is risk of personal injury and failure of
product.
Be cautious when unpacking and
installing the product.
• Sharp edges could cause injury.
Do not mix air or gas other than the
specified refrigerant used in the system .
Use a soft cloth to clean. Do not use
harsh detergents, solvents or splashing
water etc .
• There is risk of fire, electric shock, or damage
to the plastic parts of the product.
Always insert the filter securely after
cleaning. Clean the filter every two weeks
or more often if necessary.
• A dirty filter reduces the efficiency.
If the refrigerant gas leaks during the
repair, do not touch the leakaing
refrigerant gas.
• The refrigernat gas can cause frostbite (cold
burn)
If the refrigerant gas leaks during the
installation, ventilate the area immediately.
• If air enters the refrigerant system, an
excessively high pressure results, causing
equipment damage or injury.
• Otherwise it can be harmfull for your health.
Replace the all batteries in the remote
control with new ones of the same type.
Do not mix old and new batteries or
different types of batteries.
Do not recharge or disassemble the
batteries. Do not dispose off batteries in
a fire.
• There is risk of fire or product failure.
• They may burn or explode.
If the liquid from the batteries gets onto
your skin or clothes, wash it well with
clean water. Do not use the remote if the
batteries have leaked.
If you eat the liquid from the batteries,
brush your teeth and see doctor.
Do not use the remote if the batteries
have leaked.
Do not let the air conditioner run for a
long time when the humidity is very high
and a door or a window is left open.
• The chemicals in batteries could cause burns
or other health hazards.
• The chemicals in batteries could cause
burns or other health hazard.
• Moisture may condense and wet or damage
furniture.
Do not expose your skin or kids or
plants to the cool or hot air draft.
• This could harm to your health.
Do not drink the water drained from the
product.
• It is not sanitary and could cause serious
health issues.
Use a firm stool or ladder when cleaning,
maintaining or repairing the product at
an height.
• Be careful and avoid personal injury.
Owner's Manual 5
ENGLISH
• There is risk of damage or loss of property.
Do not block the inlet or outlet of air flow.
Product Introduction
Product Introduction
Here is a brief introduction of the indoor and outdoor units. Please see the information specific to your indoor
unit type.
Indoor Units
[Ceiling Cassette Type]
Cabinet
Air Discharge
Front Panel
Signal receiver
Air Inlet
Outdoor Unit
Air intake vents
Air outlet
vents
Communication cable
Refrigerant pipe
Drain hose
h The figure can be changed according to model.
6 Air Conditioner
Product Introduction
Operation Indication Lamps
•
On/Off
: Lights up during the system operation.
Filter Sign
: Lights up after 2400 hours from the time of first operating unit.
Timer
: Lights up during Timer operation.
Defrost Mode
: Lights up during Defrost Mode or Hot Start operation.(Heat pump model only)
Forced
: To operate the unit when the remote control can't be used
for any reason.
* Hot start operation: Stops the indoor fan in heating operation for minutes to prevent cold air from blowing out
from unit.
* In defrost mode unit stops heating operation for few minutes to remove formation of ice on the heat
exchanger coils to maintain the efficiency.
Operating Method
1. The signal receiver is inside the unit.
2. Aim the remote controller towards the unit to operate it.
There should not be any blockage in between.
Ceiling Cassette Type
Owner's Manual 7
ENGLISH
[Ceiling Cassette Type]
Product Introduction
Wireless Remote Controller
VANE ANGLE Button
Used to set each vane angle.
FUNCTION SETTING Button
Used to set or clear Auto Clean, Smart Clean,
Electric heater or Individual vane angle control.
ON/OFF Button
Used to turn on/off the unit.
1
2
JET COOL Button
Speed cooling operates super high fan speed.
3
10
11
12
4
13
5
6
14
UP/DOWN AIRFLOW Button
Used to stop or start louver movement and set
the desired up/down airflow direction.
15
16
ON TIMER Button
Used to set the time of starting operation.
17
SLEEP TIMER Button
Used to set the time of sleeping operation.
7
8
9
LEFT/RIGHT AIRFLOW Button (OPTIONAL)
Used to set the desired left/right(horizontal)
airflow direction.
SET / CLEAR Button
Used to set/clear the timer.
Used to set the current time(if it input for 3sec.)
PLASMA Button (OPTIONAL)
Used to start or stop the plasma-purification
function.
Operation Mode
Cooling Mode
ROOM TEMPERATURE SETTING Button
Used to select the room temperature.
Auto Mode or Auto Changeover
OPERATION MODE SELECTION Button
Used to select the operation mode.
INDOOR FAN SPEED SELECTION Button
Used to select fan speed in four steps low,
medium, high and chaos.
Dehumidification mode
Heating Mode
ROOM TEMPERATURE CHECKING Button
Used to check the room temperature.
Fan Mode
• Cooling Model(
), Heat Pump Model(
)
OFF TIMER Button
Used to set the time of stopping operation.
TIMER SETTING(Up/Down)/LIGHT Button
Used to set the timer.
Used to adjust the brightness.(if it is not time
adjust mode)
RESET Button
Used to reset the remote controller.
8 Air Conditioner
Operating instructions
Operating instructions
1
Press the ON/OFF button.
The unit will respond with beep sound.
2
Press MODE button to select Cooling Mode.
3
Set the desired temperature by pressing TEMP button.
Press ROOM TEMPERATURE CHECKING button to
check the room temperature. When setting the desired
temperature is higher than room temperature, cooling
wind isnʼt blow out.
ENGLISH
Cooling Mode - Standard Operation
To raise the temperature
To lower the temperature
h Setting Temp. Range : 18~30°C(64~86°F)
Owner's Manual 9
Operating instructions
Cooling Mode - Power Cooling
It makes the room cool using pleasant and fresh air quickly
1
Press the ON/OFF button.
The unit will respond with beep sound.
2
Press MODE button to select Cooling Mode.
3
Press the JET COOL button. The unit will operate in super
high fan speed in cooling mode.
h Wall mounted models operate power cooling mode for
30 minutes.
4
To cancel the Power cooling Mode press the Jet Cool button or the fan button
or the room temperature setting button again and the unit will operate in high
fan speed in cooling mode.
or
10 Air Conditioner
or
Operating instructions
Heating Mode
Press the ON/OFF button.
The unit will respond with beep sound.
2
Press MODE button to select Heating Mode.
3
Set the desired temperature by pressing TEMP button.
Press ROOM TEMPERATURE CHECKING button to check the room
temperature.
When setting the desired temperature is lower than room
temperature, heating wind isnʼt blow out.
To raise the temperature
To lower the temperature
4
ENGLISH
1
h Setting Temp. Range in
Heating Mode : 16~30°C
(60°F~86°F)
Set the fan speed again. You can select the fan speed in four
steps–low, medium, high, or chaos. Each time the button is pressed,
the fan speed mode is shifted.
Owner's Manual 11
Operating instructions
Dehumidification Mode
1
Press the ON/OFF button.
The unit will respond with beep sound.
2
Press MODE button to select Dehumidification Mode.
3
Set the fan speed. You can select the fan speed in four steps - low,
medium, high, or chaos. Each time the button is pressed, the fan
speed mode is shifted.
During Dehumidification Mode
• If you select the dehumidification mode on the operation selection button, the indoor unit starts to run the
dehumidification function, automatically setting the room temp. and air volume to the best condition for
dehumidification based on the sensed room temp.
In this case, the setting temp. is not displayed in the Remote Controller and you are not able to control the
room temp. either.
• During the healthy dehumidification function, the air volume is automatically set according to the algorithm
responding to the current room temp. and makes the room condition healthy and comfortable even in the
high humidity season.
12 Air Conditioner
Operating instructions
Fan Mode
Press the ON/OFF button.
The unit will respond with beep sound.
2
Press MODE button to select Fan Mode.
3
Set the fan speed again. You can select the fan speed in four
steps–low, medium, high, or chaos. Each time the button is pressed,
the fan speed mode is shifted.
ENGLISH
1
Natural Wind by the chaos Logic
• For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to chaos mode. In
this mode, the wind blows like natural breeze by automatically changing fan speed according to the chaos
logic.
During Fan Mode
• The outdoor compressor doesn't work.
Have a function to circulate the indoor as it sends out the air that doesn't have much temperature difference
with indoor.
Owner's Manual 13
Operating instructions
Temperature setting/ room temperature check
We can simply adjust the desired temperature
• Press the buttons to adjust the desired temperature
: Increase 1˚C or 1˚F per one time pressing
: Decrease 1˚C or 1˚F per one time pressing
Room temp: Indicate the current room temperature
Set temp: Indicate the temperature that user want to set
<Cooling Mode>
The cooling mode doesn't work if desired temperature is higher than
room temperature Please lower the desired temperature
<Heating Mode>
The heating mode doesn't work if desired temperature is lower than room
temperature Please increase the desired temperature
Whenever press button, the room temperature will be displayed within 5
seconds.
After 5 seconds, it turns to display the desired temperature.
Because of location of remote controller, the real room temperature and
the this displayed value can be different.
14 Air Conditioner
Operating instructions
Sub function : Plasma Purification(Optional)
ENGLISH
1
Press the ON/OFF button.
The unit will respond with beep sound.
2
Press the PLASMA button. Plasma Purification will
start when the button is pressed and stop when the
button is pressed again.
PLASMA Purification only
If you press the PLASMA button, Plasma Purification operates.
• Plasma filter is a technology developed by LG to get rid of
microscopic contaminants in the intake air generating a
plasma of high charge electrons. This plasma kills and
destroys the contaminants completely to provide clean and
hygienic air.
• This function can be used in any operation mode and any fan
speed can be used while plasma filter is functioning.
Owner's Manual 15
Operating instructions
Installer Setting-Celsius / Fahrenheit Switching
This function is used for switching the display between Celsius and Fahrenheit.
Press the °C/°F SWITCH button to change from Celsius to Fahrenheit or from Fahrenheit to Celsius.
Whenever press TEMPERATURE SETTING button in Fahrenheit mode, the temperature
will increase/drop 1°F.
Function setting : Individual vane angle control
It is the function that can control 4 vane angles individually in the ceiling type 4Way cassette product
group.
1
Press the VANE ANGLE button.
Individual vane angle control symbol will blink.
• If you press the VANE ANGLE button for 3 seconds in that time,
all vanes are set to standard angle.
2
Set each vane angle by pressing the VANE ANGLE button.
3
Press SET/CLEAR button to reserve or cancel the individual vane
angle control function.
• There may be differences between wireless remote controller up/down/left/right buttons and the wind discharge
port directions.
• Set desired angle with checking the vane angle movement of the product.
• The individual vane control function is an additional function of a product, and it may not work in some products.
16 Air Conditioner
Operating instructions
Sleep Timer Setting
1. Press the TIMER button to turn timer on or off.
3. Press the SET / CLEAR button.
On Timer Setting
1. Press the ON button to turn timer on or off.
Heure de mise en marche programmée
2. Press TIME SETTING buttons until the desired time
is set.
3. Press the SET / CLEAR button.
Off Timer Setting
1. Press the OFF button to turn timer on or off.
Heure d'arrêt programmé
2. Press TIME SETTING buttons until the desired time
is set.
3. Press the SET / CLEAR button.
To cancel the Timer Setting
• If you wish to cancel all timer setting, press the CLEAR ALL button.
• If you wish to cancel each timer setting, press the
each timer button to turn timer sleep or on or off as you want.
And then press the SET/CLEAR button aiming the remote
controller at the signal receptor.
(The timer lamp on the air conditioner and the display will go off.)
Owner's Manual 17
ENGLISH
Veille programmée
2. Press TIME SETTING buttons until the desired time
is set. (7 hours is the maximum setting)
Operating instructions
Forced operation
Operation procedures when the remote control can't be used.
The operation will be started if the ON/OFF button is pressed.
If you want to stop operation, re-press the button.
[Ceiling Cassette Type]
Forced Operation
Button
Operating mode
Indoor FAN Speed
Setting Temperature
Room Temp. ≥ 24°C(75.2°F)
Cooling
High
22°C(72°F)
21°C(69.8°F) ≤ Room Temp. < 24°C(75.2°F)
Healthy Dehumidification
High
23°C(74°F)
Room Temp. < 21°C(69.8°F)
Heating
High
24°C(76°F)
Test operation
During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of room
temperature and resets in 18 minutes.
During test operation, if remote controller signal is received, the unit operates as remote controller sets.
If you want to use this operation, Press and hold the ON/OFF button for 3~5 seconds, then the buzzer sound
1 "beep".
If you want to stop the operation, re-press the button.
18 Air Conditioner
Maintenance and Service
Maintenance and Service
Grille, Case and Remote Control
p Turn the system off before cleanining, To clean, wipe with a soft, dry cloth. Do not use bleach or abrasives.
NOTE
Supply power must be disconnected before cleaning the indoor unit.
Air Filters
The air filters behind the front grille should be checked
and cleaned once every 2 weeks or more often if
neccessary.
1
Remove the Air filters.
n Take hold of the tab and pull slightly forward to
remove the filter.
CAUTION: When the air filter is to
be removed, do not touch the metal
parts of the indoor unit.
It may cause an injury.
n Never use any of the followings:
• Water hotter than 40°C.
Could cause deformation and/or discoloration.
• Volatile substances.
Could damage the
surfaces of the air
conditioner.
SI
B en
z ene
N N ER
2
Clean dirt from the air filter using a vacuum
cleaner or washing with water.
n If dirt is conspicuous, wash with a neutral
detergent in lukewarm water.
n If hot water (50°C or more) is used, it may be
deformed.
3
After washing with water, dry well in the
shade.
n Do not expose the air filter to direct sunlight
or heat from a fire when drying it.
4
Install the air filter.
S CO
U RI N
CLB
ARGE
Owner's Manual 19
ENGLISH
Indoor Unit
Maintenance and Service
Purifying filter(Optional)
Cleaning
The PLASMA filter behind the air filters should be
checked and cleaned once every 3 months or more
often if necessary.
1
After removing the air filters, pull slightly forward to
remove the PLASMA filter.
2
Dip the PLASMA filter into the water mixed with neutral
detergent, for 20~30 minutes.
3
Dry the PLASMA filter in the shade for a day
(Especially, the humidity must be removed perfectly on
this parts).
4
Note the cuts of electric discharge lines.
5
Re-install the PLASMA filter to the original position.
CAUTION:Donʼt touch this
PLASMA Filter within 10 seconds
after opening the inlet grille, it
may cause an electric shock.
Replacement
• Recomended use period : About 2 years
1
Open front panel and remove air filter.
2
Remove air purifying filter.
3
Insert new air purifying filter.
2
1
4
Reinsert air filter and close front panel.
20 Air Conditioner
Maintenance and Service
Operation Tips!
Keep blinds or curtains
closed.
This is not good for the health and
wastes electricity.
Do not let direct sunshine enter the
room when the air conditioner is in
operation.
Make sure that the doors
and windows are shut tight.
Clean the air filter regularly.
Avoid opening doors and windows
as much as possible to keep the
cool air in the room.
Blockages in the air filter reduce the
airflow and lower cooling and
dehumidifying effects. Clean at least
once every two weeks.
Keep the room temperature
uniform.
Adjust the vertical and horizontal
airflow direction to ensure a uniform
temperature in the room.
Ventilate the room
occasionally.
Since windows are kept closed, it is
a good idea to open them and
ventilate the room now and then.
When the air conditioner is not going....
When air conditioner is not going to be used for a long time.
1 Operate the air conditioner at the following settings for 2 to 3 hours.
• Type of operation: Fan operation mode.(Refer to page 16.)
• This will dry out the internal mechanisms.
2 Turn off the breaker.
CAUTION: Turn off the breaker when the air conditioner is not going to be
used for a long time.
Dirt may collect and may cause a fire.
3. Remove the batteries from the Remote Controller.
Helpful information
The air filters and your electiric bill.
If the air filters become clogged with dust, the cooling capacity will drop, and 6% of the electricity used to
operate the air conditioner will be wasted.
When the air conditioner is to be used again.
1. Clean the air filter and install it in the indoor unit.
(Refer to page 34 for cleaning it.)
2. Check that the air inlet and outlet of the indoor/outdoor unit are not blocked.
3. Check that the ground wire is connected correctly. It may be connect to the indoor unit side.
Owner's Manual 21
ENGLISH
Do not overcool the room.
Maintenance and Service
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the malfunction persist, please contact your dealer.
Case
Explanation
The air conditioner does not
operate.
• Have you made a mistake in timer operation?
The room has a peculiar odor.
• Check that this is not a damp smell exuded by the walls, carpet, furniture
or cloth items in the room.
It seems that condensation is
leaking from the air conditioner.
• Condensation occurs when the airflow from the air conditioner cools the
warm room air.
Air conditioner does not operate
for about 3 minutes when restart.
• This is the protector of the mechanism.
Does not cool or heat effectively.
• Is the air filter dirty? See air filter cleaning instructions.
• Has the fuse blown or has the circuit breaker been tripped?
• Wait about three minutes and operation will begin.
• The room may have been very hot when the room air conditioner was first
turned on. Allow time for it to cool down.
• Has the setting temperature been set incorrectly?
• Are the indoor unit's air inlet or outlet vents obstructed?
The air conditioner operation is
noisy.
• For a noise that sounds like water flowing.
-This is the sound of freon flowing inside the air conditioner unit.
• For a noise that sounds like the compressed air releasing into atmosphere.
-This is the sound of the dehumidifying water being processed inside the
air conditioning unit.
Crack sound is heard.
• This sound is generated by the expansion/contraction of the inlet grille, etc.
due to changes of temperature.
Filter sign lamp (LED) is ON.
• Cleaning the filter, press the Timer button and ◀ button of wired remote
controller at the same time for 3 sec.
Remote control display is faint, or
no display at all.
• Has the circuit breaker been tripped?
• Are the batteries inserted in the opposite (+) and
(-) directions? Call the service immediately in the following situations
1. Anything abnormal such as burning smell, loud noise etc. happen. Stop the unit and turn the breaker off.
Never try to repair by yourself or restart the system in such cases.
2. Main power cord is too hot or damaged.
3. Error code is generated by self diagnosis.
4. Water leaks from indoor unit even if the humidity is low.
5. Any switch, breaker (safety, earth) or fuse fails to work properly
User must carry routine checkup & cleaning to avoid unitʼs poor performance.
In case of special situation, the job must be carried out by service person only.
22 Air Conditioner
US
CANADA
1. Please call the installing contractor of your product, as warranty service will be provided by them.
2. If you have service issues that have not been addressed by the contractor, please call 1-888-865-3026.
Service call Number # : (888) LG Canada, (888) 542-2623
Download PDF

advertising