LG | SG-S1899 | LG SG-S1899 Owner’s Manual

Room Air Conditioner
OWNER'S MANUAL
WINDOW TYPE ROOM AIR CONDITIONER
TABLE OF CONTENTS
FEATURES
2
OPERATING
3
FUNCTION
3
VENTILATION
5
TO CONTROL AIR DIRECTION
5
HOW TO ATTACH DRAIN PAN
6
AIR FILTER CLEANING
6
HOW TO ATTACH FRONT GRILLE TO CABINET
7
INSTALLATION
8
HOW TO INSTALL THE UNIT
8
HOW TO USE THE REVERSIBLE INLET GRILLE
9
WARNINGS
10
PLEASE CHECK BEFORE SERVICE CALL
11
SUPER GENERAL COMPANY WORKSHOPS IN THE U.A.E
12
FEATURES
1
5
7
6
4
3
10
2
8
9
1. CABINET
7. AIR FILTER
2. HORIZONTAL AIR DEFLECTOR
8. CONTROL PANEL
(VERTICAL LOUVER)
9. POWER CORD
3. VERTICAL AIR DEFLECTOR
10. EVAPORATOR
(HORIZONTAL LOUVER)
11. CONDENSER
4. AIR DISCHARGE
5. FRONT GRILLE
6. AIR INTAKE
(INLET GRILLE)
12. COMPRESSOR
13. BASE PAN
14. BRACE
15. COVER CONTROL
_2_
15
12 13
14
11
2..........................................................................................
3............................................................................................
3.........................................................................................
5..........................................................................................
5................................................................................
6.............................................................................
6.................................................................
7.................................................................................
8..........................................................................................
8..................................................................................
9.....................................................................
10........................................................................................
11.........................................................................
12...................................................................
1
5
7
6
4
3
10
2
8
9
15
12
13
14
11
-7
-1
-8
-2
-9
-10
-3
-11
-12
-3
-13
-5
-14
-6
-15
_2_
OPERATING
CAUTION
?
When the air conditioner has been
the fan
position,
performing
wait at least 3 minutes before
its
cooling operation and is turned off or
resetting to the cooling operation again.
set to
FUNCTION
Thermostat
Auto
5
4
Operation
Swing
Off
6
Off
3
On
0
Med
Fan
Cool
Low
Fan
Med
Cool
High
7
2
8
1
9
Low Cool
?
THERMOSTAT
Thermostat will
?
automatically
temperature of the
number for lower
room.
room
control the
Select
OPERATION
OFF
(
MED FAN
(
0
)
:
)
:
higher
off.
temperature.
The temperature is selected by turning
the knob to the desired position.
The 5
6
or
is
position
a
normal
Lamp
is
lighted
?
setting for
LOW FAN
(
Air
):
while OPERATION knob
position.
swing
is
operated
while
OPERATION knob is set to the
COOL
OFF(
)
:
Stops
position.
operation
the
(
)
:
without
Permits the low fan
without
AUTO SWING
ON
Permits the med fan
speed operation
cooling.
average conditions.
is set to the COOL
Turns the air conditioner
of air
swing.
_3_
HIGH COOL
(
)
:
MED COOL
(
)
:
LOW COOL
(
)
:
speed
cooling.
operation
Permits cooling with the
high fan speed operation.
Permits cooling with the
med fan speed operation.
Permits cooling with the
low fan speed operation.
Thermostat
Auto
5
4
Operation
Swing
Off
6
Off
3
On
0
Med
Fan
Cool
Low
Fan
Med
Cool
High
7
2
8
1
9
Low Cool
(
_3_
:(
)ON?
:(
)OFF?
0
):OFF?
:(
)MED
FAN?
:(
)LOW
FAN?
:(
)HIGH COOL?
:(
)MED COOL?
:(
)LOW COOL?
?
CAUTION
When the air conditioner has been
the fan
position,
performing
wait at least 3 minutes before
its
cooling operation and is turned off or
resetting to the cooling operation again.
set to
FUNCTION
?
THERMOSTAT
?
Turn the thermostat control to the desired
setting. The control position is a normal
setting for average conditions. You can
change this setting, if necessary, in
accordance with your temperature preference.
heating,
( O )
:
LOW FAN
(
)
:
automatically controls cooling
runs continuously
air conditioner is in operation. If
LOW COOL
(
)
:
HIGH COOL
(
)
:
LOW HEAT
(
)
:
HIGH HEAT
(
)
:
but the fan
whenever the
the
OFF
is too warm, turn the thermostat
control clockwise. If the room is too cool, turn
room
the thermostat control counterclockwise.
?
Turns the air conditioner
off.
The thermostat
or
OPERATION
Permits the low fan
speed
operation without cooling
(heating).
Permits cooling with the
low fan speed operation.
Permits cooling with the
high fan speed operation.
Permits heating with the
low fan speed operation.
Permits heating with the
high fan speed operation.
HEATER LAMP
When the unit sets
heating operation
?
condition, the green lamp is lighted.
When the frost settles
on
the heat
ON
exchanger
of the outside, defrosting is made
automatically and the green lamp is turned off.
The unit may give a hiss and the fan motor
stops for 1 to 10 minutes.
This should not be
After
defrosting,
again.
AUTO SWING
regarded as a problem.
heating operation begins
the
_4_
(
)
:
Air
swing
is
operated
while
OPERATION knob is set to
the COOL
OFF
(
)
:
or
HEAT
Stops the operation
swing.
position.
of air
(
_4_
:(
)ON?
:(
)OFF?
O
):OFF?
FAN?
:(
)LOW
:(
)LOW COOL?
:(
)HIGH COOL?
:(
)LOW
HEAT?
:(
)HIGH
HEAT?
VENTILATION
The ventilation lever must be in the CLOSE position in order to maintain the best
conditions.
When fresh air is necessary in the room, set the ventilation lever to the OPEN position.
The damper is opened and room air is exhausted.
cooling
Part B
CLOSE
VENT
OPEN
NOTE: Before using the ventilation feature,
make the lever, as shown. First, pull down
part £ to horizontal line with part £
Part A
.
TO CONTROL AIR DIRECTION
The direction of air
can
be controlled wherever you want to cool
by adjusting
the horizontal
louver and the vertical louver.
?
HORIZONTAL AIR-DIRECTION CONTROL
To control horizontal direction of air flow, set
to the ON
position
the air flow will be
automatic
swing switch and
swept horizontally by the
air-swing system.
If you want to
?
the auto
stop the air flow from moving,
switch off the auto
swing
desired
vane.
position
of the
switch at the
VERTICAL AIR-DIRECTION CONTROL
The vertical auto direction is
moving
_5_
the horizontal louver.
adjusted by
B
A
A
B
ON
_5_
HOW TO ATTACH DRAIN PAN
The air conditioner
removed from the
employs a proper drain method whereby
air) is drained to the outside.
the condensed water
(moisture
In very humid weather, (and for reverse cycle models) excessive condensate water removed
from the air may cause some water to collect. To remove this excess water you can install the
drain pan as detailed below.
1. Take the drain pan which is located in the air
discharge.
2. Remove the hole rubber from the base pan bottom hole, and attach it to the base pan
hole. (for some models).
rear
3. Install the drain pan to the right cor ner of the cabinet with 4 (or 2) screws.
4. Connect the drain hose to the outlet located at the bottom of the drain pan.
You
can
purchase
hose is not
(Drain
the drain hose
or
tubing locally
to
satisfy your particular
needs.
supplied).
CABINET
DRAIN
PAN
SCREW
DRAIN HOSE
AIR FILTER CLEANING
The air filter should be checked at least twice
a
month to
see
if
cleaning
particles in the filter will build up and block the airflow. This reduces the
also causes an accumulation of frost on the cooling coils.
1.
Open
the inlet
grille upward by pulling
out the bottom of the inlet
is necessary.
Trapped
cooling capacity and
grille.(a)
In another case, you can open the inlet grille downward by pulling out the top of the inlet
2. Remove the air filter from the front grille assembly by pulling the air filter up or down
3. Wash the filter
4.
Gently
using
shake the
lukewarm water below
excess
NOTE: Mark "Δ" of inlet
C (104¡£
40¡£
F).(c)
completely. Replace
water from the filter
grille
means
opening
grille.(b)
slightly.
the filter.
direction.
(a)
(b)
_6_
(c)
.(a)
.(b)
.(c)
(a)
(b)
_6_
(c)
HOW TO ATTACH FRONT GRILLE TO CABINET
1. Pull down front
grille from the cabinet top.
grille's tips toward the cabinet in order to insert front grille's tabs
the
inlet
Open
grille.
Tighten the screw through the front grille into the plate of the evaporator.
Close inlet grille.
2. Push front
3.
4.
5.
_7_
_7_
into the cabinet.
INSTALLATION
HOW TO INSTALL THE UNIT
AWNING
FENCE
FOAM
1/4 Bubble
BASE COOLED
PAN
AIR
Level
70-15cm
DRAIN TUBE
1. To avoid vibration and noise, make sure
the unit is installed securely and firmly.
2. Install the unit where the sunlight does not
shine directly on the unit.
If the unit receives direct sunlight, build an
awning
to shade the cabinet.
3. There should be no obstacle, like a fence,
within 50cm which might restrict heat
radiation from the condenser.
4. To
prevent reducing performance, install
the unit so that louvers of the cabinet are
not blocked.
5. Install the unit a little obliquely outward not
to leak the condensed water into the room
(about 10~15mmor 1/4 bubble with level).
6. Install the unit with its bottom
75-150cm above the floor level.
portion
7. Stuff the foam between the
top of the unit
and the wall to prevent air and insects from
getting into the room.
8. The power cord must be connected to an
independent circuit. The green wire must
be grounded.
9. Connect the drain tube to the base pan
rear hole in the rear side. Drain hose or
equivalent may be connected to the drain
tube. (Drain hose is not supplied.)
When the base pan rear hole is open,
connect the drain tube.
When the base pan rear hole is capped
with hole rubber, replace with the drain
tube if you need to drain.
In very humid area, you can install the
drain pan. (Refer to page 6)
?
?
6
_8_
_8_
HEAT
RADIATION
10~15mm
Over 50cm
HOW TO USE THE REVERSIBLE INLET GRILLE
The
grille
is
designed
to clean the filter both
upward
and downward.
b
(a)
A. Before
(b)
attaching
cabinet,
the front
if you want to
upward;
1. Open the
pull
grille
(c)
to the
out the filter
inlet
grille slightly (a).
grille (a).
Disassemble the inlet grille from the front
grille with separating the hinged part by
inserting a "--" type screw-driver tip (b).
Then, rotate the inlet grille 180 degrees
a
2. Turn inside out the front
3.
4.
a
b
and insert the hooks into bottom holes of
the front
grille.
5. Insert the filter and attach the front
the cabinet
(refer
B. If you want to
pull
to page
grille
7).
to
7
out the filter
downward;
The
grille
is
already designed
for that way.
_9_
_9_
WARNINGS
Listed below
are
important
instructions which
will
prevent malfunctions of the unit
serious problem with your air conditioner.
1.
2.
or
Operate the unit from a stable power
supply voltage variation must be within
±10 percent of the rated voltage.
DO NOT modify any part of the unit.
3. DO NOT put sticks, rods, etc. into any part
of the unit.
4. DO NOT
operate the unit without
filter because dirt and lint will
reduce
clog
an
air
it and
performance.
5. DO NOT hold the power cord
wet hand.
plug
with
6. DO NOT obstruct the air inflow of the
evaporator, it may
unplug your
unit
trouble.
cause some
7. Turn the mode control to "O"
during
checking
or
the cool
when you are
the unit.
8. Close the ventilation damper
days
and/or
during heavy
"OFF" and
season or
on
windy
rains.
NOTE: We
strongly recommend that any
servicing be performed by a qualified
individual.
OFF
_10_
_10
_
O
PLEASE CHECK BEFORE SERVICE CALL
When you find something wrong with your room air conditioner, please check carefully referring
to the following items. If you can't find out the causes of trouble, get into contact with your
dealer.
A. WHEN AIR CONDITIONER DOES
NOT
OPERATE;
1. Is the air conditioner
NOT COOL AS IT
into the
plugged
1. Is the
2. Is the unit connected to
supplying
the proper
3. Is the fuse blown
or
a
live
voltage?
is the automatic circuit
local power failure?
another electrical product.
furniture, etc.,
accidentally
comparing
an
by
an
other devices
line?
or
unusual heat
windows open, or is there
in the room?
source
maximum
to the
temperature of indoor?
large enough
damper
cooling?
7. Is the air filter clean
extension cord is used, is the wire
diameter
by drapes,
improper vane
an
setting?
5. Are the doors
7. Is the thermostat knob set too low
8. If
by
or
6. Is the ventilation
6. Is the circuit overloaded
same
the desired
3. Are there too many
number in the room?
a
switched off?
the
properly?
properly to
cooling?
people than the usual
4. Is the air circulation restricted
5. Has the air conditioner been
on
switch set
operation
provide
receptacle
breaker off?
4. Is there
SHOULD;
2. Is the thermostat control set
receptacle properly?
Try
B. WHEN AIR CONDITIONER DOES
to carry the
so
closed for
that it will not
obstruct the air flow?
8. Have all the steps outlined in the
Installation Instructions been followed?
9. Is the evaporator frosted?
evaporator may
current?
occur
Frosting of the
during the spring and
autumn months if there is a considerable
during cool weather. If
operation switch to "MED FAN".
The fast air circulation will quickly defrost
the coil so that normal cooling operating
temperature drop
so, turn the
may be resumed.
_11_
or
_11_
SUPER GENERAL COMPANY WORKSHOPS IN THE U.A.E
DUBAI(CENTROL WORKSHOP)
04-2685849
ABU DHABI
02-720925
AL AIN
03-213901 / 6230854
FUJAIRAHA
09-2222396 / 22229330
RAS AL KHAIMAH
07-2238849 / 334576
SHARJAH / AJMAN
06-5333594
UM AL QUWAIM
06-7656649
_12_
04-2685849
02-720925
03-213901 / 6230854
09-2222396 / 22229330
07-2238849 / 334576
06-5333594
06-7656649
_12_
P/NO.: 3828A30085Y
Printed in Korea
Download PDF