LG | 47LD452B | LG 47LD452B Owner’s Manual

OWNER’S MANUAL
LED LCD TV / LCD TV
Please read this manual carefully before operating
your set and retain it for future reference.
The model and serial number of the TV is located
on the back and/or one side of the TV.
Record it below should you ever need service.
LED LCD TV MODELS
19LE5300
32LE5300
22LE5300
37LE5300
26LE5300
42LE5300
22LE5500
47LE5300
26LE5500
55LE5300
42LE7300
47LE7300
55LE7300
42LE530C
47LE530C
55LE530C
LCD TV MODELS
32LD420
32LD520
42LD420
42LD520
47LD420
47LD520
32LD450
55LD520
37LD450
42LD630
42LD450
47LD630
47LD450
55LD630
37LD450C
42LD450C
47LD450C
55LD520C
42LD451C
47LD451C
26LD352C
32LD452C
37LD452C
42LD452C
47LD452C
32LD452B
42LD452B
47LD452B
MODEL
SERIAL
P/NO : SAC34134204 (1106-REV14)
www.lg.com
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the
point of the cable entry as practical.
2
FCC Notice
Class B digital device
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC
Rules.
Operation is subject to the following two conditions: (1) This device may not cause (harmful)
interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation (of the
device).
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any
way without written authorization from LG
Electronics.
Unauthorized modification could void the user’s
authority to operate this product.
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
10
Heed all warnings.
Follow all instructions.
1
Do not use this apparatus
near water.
2
Clean only with dry cloth.
3
Do not block any ventilation
openings. Install in accordance
with
the
manufacturer’s
instructions.
4
Do not install near any heat
sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
5
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider
than the other. A grounding
type plug has two blades and a
third grounding prong, The wide
blade or the third prong are
provided for your safety. If the
provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
6
Protect the power cord from
being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the
apparatus.
7
Only use attachments/accessories specified by the manufacturer.
8
Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When
a cart is used, use caution
when moving the cart/apparatus combination to avoid injury
from tip-over.
9
Unplug this apparatus during
lighting storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
11
Never touch this apparatus or antenna during a thunder or lighting storm.
12
When mounting a TV on the wall, make sure
not to install the TV by the hanging power
and signal cables on the back of the TV.
13
Do not allow an impact shock or any objects
to fall into the product, and do not drop
onto the screen with something.
14
CAUTION concerning the Power Cord:
It is recommend that appliances be placed
upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance and has no additional outlets or
branch circuits. Check the specification
page of this owner's manual to be certain.
Do n ot connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.
Do not overload wall outlets. Overloaded
wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or
damaged or cracked wire insulation are
dangerous . Any of these conditions could
result in electric shock or fire. Periodically
examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an
exact replacement part by an authorized
servicer. Protect the power cord from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to
plugs, wall outlets, and the point where the
cord exits the appliance.
Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug
when unplugging the power cord. Do not
pull on the power cord to unplug the TV.
3
SAFETY INSTRUCTIONS
15
WARNING - To reduce the risk of
fire or electrical shock, do not
expose this product to rain,
moisture or other liquids. Do not
touch the TV with wet hands. Do
not install this product near
flammable objects such as gasoline or candles or expose the
TV to direct air conditioning.
16
Do not expose to dripping or
splashing and do not place
objects filled with liquids, such
as vases, cups, etc. on or over
the apparatus (e.g. on shelves
above the unit).
17
GROUNDING
Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e. a TV with
a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If
grounding methods are not possible, have a
qualified electrician install a separate circuit
breaker.
Do not try to ground the unit by connecting it to
telephone wires, lightening rods, or gas pipes.
22
Ground Clamp
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The
plug must remain readily operable.
19
As long as this unit is connected to the AC
wall outlet, it is not disconnected from the AC
power source even if you turn off this unit by
SWITCH.
20
21
4
Cleaning
When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may
occur. Do not clean with chemicals such as
alcohol, thinners or benzene.
Moving
Make sure the product is turned off, unplugged
and all cables have been removed. It may
take 2 or more people to carry larger TVs. Do
not press against or put stress on the front
panel of the TV.
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Power
Supply
Short-circuit
Breaker
18
ANTENNAS
Outdoor antenna grounding
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system should not be located in the vicinity of
overhead power lines or other electric light
or power circuits, or where it can come in
contact with such power lines or circuits as
death or serious injury can occur.
Be sure the antenna system is grounded so
as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information
with respect to proper grounding of the
mast and supporting structure, grounding
of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location
of antenna discharge unit, connection to
grounding electrodes and requirements for
the grounding electrode.
Antenna grounding according to the
National Electrical Code, ANSI/NFPA 70
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
NEC: National Electrical Code
23
Ventilation
Install your TV where there is proper ventilation. Do not install in a confined space such
as a bookcase. Do not cover the product
with cloth or other materials (e.g.) plastic
while plugged in. Do not install in excessively dusty places.
24
Take care not to touch the ventilation openings. When watching the TV for a long
period, the ventilation openings may
become hot.
25
If you smell smoke or other odors coming
from the TV, unplug the power cord contact
and authorized service center.
26
Do not press strongly upon the
panel with hand or sharp object
such as nail, pencil or pen, or
make a scratch on it.
27
Keep the product away from direct sunlight.
28
Dot Defect
The Plasma or LCD panel is a high technology product with resolution of two million to
six million pixels. In a very few cases, you
could see fine dots on the screen while you’re
viewing the TV. Those dots are deactivated
pixels and do not affect the performance and
reliability of the TV.
29
Generated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated by plastic thermal contraction due to
temperature and humidity. This noise is common for products where thermal deformation
is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a high-speed
switching circuit, which supplies a large amount
of current to operate a product. It varies
depending on the product.
This generated sound does not affect the
performance and reliability of the product.
30
For LED LCD TV/LCD TV
If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.
Some minute dot defects may be visible on
the screen, appearing as tiny red, green, or
blue spots. However, they have no adverse
effect on the monitor’s performance.
Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
ON DISPOSAL
(Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not
dispose of this product with general household waste. Disposal of this product must be
carried out in accordance to the regulations of
your local authority.
5
CONTENTS
WARNING / CAUTION............................... 2
SAFETY INSTRUCTIONS
Important Safety Instructions............................... 3
FEATURE OF THIS TV................................. 8
PREPARATION
Accessories..............................................................9
Front Panel Information...................................... 11
Back Panel Information......................................16
Stand Instructions...............................................20
VESA wall mounting..........................................28
Cable Management...........................................30
Desktop Pedestal Installation..........................32
Swivel Stand .........................................................32
Kensington Security System...........................32
Attaching the TV to a Desk.............................33
Securing the TV to the Wall to Prevent Falling
when the TV is used on a stand....................34
Antenna or Cable Connection........................35
EXTERNAL EQUIPMENT SETUP
HD Receiver setup..............................................36
DVD setup.............................................................39
VCR SETUP........................................................... 41
Other A/V Source Setup..................................42
USB Connection.................................................43
Headphone Setup ............................................43
Audio out Connection.......................................44
PC Setup...............................................................45
WATCHING TV / CHANNEL CONTROL
Remote Control Functions...............................52
Turning on the TV...............................................54
Channel Selection..............................................54
Volume Adjustment...........................................54
Initial Setting........................................................55
On-Screen Menus Selection........................... 57
Quick menu..........................................................59
Customer Support
6
- Picture Test / Sound Test............................60
- Product/Service Info........................................ 61
Simple Manual.....................................................62
Channel Setup
- Auto Scan (Auto Tuning)...............................63
- Add/Delete Channel (Manual Tuning)......64
- Channel Editing................................................65
Favorite Channel Setup.....................................66
Favorite Channel List.........................................66
Channel List......................................................... 67
Channel Information..........................................68
Channel Brief Information................................ 69
Input List............................................................... 70
Input Label............................................................. 71
Reset to factory default (Initial Setting)....... 72
Mode Setting....................................................... 73
Demo Mode......................................................... 74
AV Mode................................................................ 75
SIMPLINK.............................................................. 76
MY MEDIA
Connection Method........................................... 78
Entry Mode........................................................... 79
Movie List............................................................. 80
Photo List.............................................................. 87
Music List..............................................................93
Extra Contents..................................................... 97
EzSign TV..............................................................98
DivX Registration Code /Deactivation..........99
PICTURE CONTROL
Picture Size (Aspect Ratio) Control.............100
Picture Wizard.................................................... 102
ꕊ Energy Saving............................................. 104
Preset Picture Settings (Picture mode)..... 105
Manual Picture Adjustment - User Mode.106
Picture Improvement Technology (Advanced
Control).................................................................107
Expert Picture Control.....................................108
Picture Reset.........................................................111
Power Indicator.....................................................111
TruMotion............................................................. 112
SOUND & LANGUAGE CONTROL
Auto Volume........................................................ 113
Clear Voice II....................................................... 114
Balance................................................................. 115
Preset Sound Settings (Sound Mode)........ 116
Sound Setting Adjustment - User Mode....117
Audio Reset......................................................... 118
TV Speakers On/Off Setup............................ 119
External Speakers On/Off Setup.................. 119
Stereo/SAP Broadcast Setup....................... 120
Audio Language ............................................... 121
On-screen Menus Language Selection..... 122
Caption Mode
- Analog Broadcasting System Captions.. 123
- Digital Broadcasting System Captions.... 124
- Caption Option............................................... 125
APPENDIX
Troubleshooting................................................. 142
Maintenance....................................................... 145
Product Specifications.................................... 146
IR Code................................................................. 151
External Control through RS-232C............ 152
Open Source License...................................... 158
TIME SETTING
Clock Setting
- Auto Clock Setup.......................................... 126
- Manual Clock Setup......................................127
Auto On/Off Time Setting............................. 128
Sleep Timer Setting......................................... 129
Auto Shut-Off Setting..................................... 129
PARENTAL CONTROL / RATINGS
Set Password & Lock System
- Setting up Your Password........................... 130
- Set Password................................................... 131
- Lock System.................................................... 132
Channel Blocking.............................................. 133
Movie & TV Rating........................................... 134
Downloadable Rating....................................... 139
External Input Blocking................................... 140
Key Lock............................................................... 141
7
FEATURE OF THIS TV
ꔛ
Some of these features are not available on all models.
High-definition
television.
Highresolution digital television broadcast
and playback system composed of
roughly a million or more pixels, 16:9
aspect-ratio screens, and AC3 digital
audio. A subset of digital television,
HDTV formats include 1080i and 720p
resolutions.
AV Mode is three preset picture and
audio settings. It allows the viewer to
quickly switch between common settings. It includes Cinema, Sports, and
Game Modes.
A unique invisible speaker system
tuned by renowned audio expert, Mr.
Mark Levinson. Speakers are embedded in strategic spots behind the front
cabinet and use minute vibrations to
turn the entire front bezel into the
speaker system. The result s a clean,
polished look, and enhanced audio by
increasing the “sweet spot”, giving a
wider and richer sound field.
Automatically enhances and amplifies
the sound of human voice frequency
range to help keep dialogue audible
when background noise swells.
Unlike other sensors which can only
sense brightness of ambient light, LG’s
“Intelligent Sensor” uses 4,096 sensing steps to evaluate its surroundings.
Using a sophisticated algorithm, the LG
processes picture quality elements
including brightness, contrast, color,
sharpness and white balance. The result
is a picture optimized for it’s surroundings, more pleasing to watch and which
can also save up to 50% in power consumption.
Manufactured under license from Dolby
Laboratories. “Dolby “and the double-D
symbol are trademarks of Dolby
Laboratories.
HDMI, the HDMI logo and HighDefinition Multimedia Interface are
trademarks or registered trademarks of
HDMI Licensing LLC."
Displays HDTV programs in full 1920 x
1080p resolution for a more detailed
picture.
View videos and photos and listen to
music on your TV through USB 2.0
(‘videos’ dependent on model).
ABOUT DIVX VIDEO: DivX® is a digital
video format created by DivX,Inc. This is
an official DivX Certified device that
plays DivX video. Visit www.divx.com for
more information and software tools to
convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND:
This DivX Certified® device must be
registered in order to play DivX Videoon-Demand (VOD) content. To generate the registration code, locate the
DivX VOD section in the device setup
menu. Go to vod.divx.com with this
code to complete the registration process and learn more about DivX VOD.
“DivX Certified® to play DivX® video up
to HD 1080p, including premium content”
“DivX®, DivX Certified® and associated
logos are registered trademarks of
DivX, Inc. and are used under license.”
Pat. 7,295,673; 7,460,668; 7,515,710;
7,519,274
IMPORTANT INFORMATION TO PREVENT “IMAGE
BURN / BURN-IN” ON YOUR TV SCREEN
ꔛ
ꔛ
ꔛ
8
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed
on the TV for an extended period, it can become permanently imprinted on the screen. This
phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged
period (2 or more hours for LCD, 1 or more
hours for Plasma).
Image burn can also occur on the letterboxed areas of your TV if you use the 4:3
aspect ratio setting for an extended period.
PREPARATION
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.
The accessories included may differ from the images below.
PREPARATION
(For 32/42/47LD452B)
1.5V 1.5V
1,5Vcc 1,5Vcc
1.5V 1.5V
Owner’s Manual
CD Manual
EzSign TV Editor
S/W & Manual
1,5Vcc 1,5Vcc
Option Extras
Not included with all models
* Wipe spots on the exterior only with the
polishing cloth.
Polishing Cloth
Remote Control,
1.5V 1.5V
Batteries (AAA)
* Do not wipe roughly when removing
stains. Excessive pressure may cause
scratches or discoloration.
D-sub 15 pin Cable
When using the VGA (D-sub 15
pin cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain standards compliance.
19/22/26LE5300, 22/26LE5500
(For 26LE5300,
26LE5500)
x4
x4
(M4 x 14)
(M4 x 20)
Screws for stand assembly
(Refer to P.20, 22)
(For 26LE5300,
26LE5500)
1.5V 1.5V
x4
Cable Holder
(Refer to p.31)
1,5Vcc 1,5Vcc
Ring spacers
(Refer to p.29)
AC/DC Adapter
Power Cord
32/37/42/47LD450, 37/42/47LD450C, 42/47/55LD630, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C
(For 37/42/47LD450C,
32/37/42/47LD452C,
32/42/47LD452B,
26LD352C)
(For 32/37/42LD450, 37/42/LD450C,
42LD630, 42LD451C, 32/37/42LD452C,
32/42LD452B, 26LD352C)
x8
1.5V 1.5V
1,5Vcc 1,5Vcc
(M4 x 20)
Screws for stand Screws for stand fixing
assembly
(Refer to P.33)
(Refer to P.24)
Protection Cover
(Refer to P.25)
Power Cord
Protective Bracket
and Screw for
Power Cord
(Refer to P.30)
9
1,5Vcc 1
PREPARATION
32/42/47LD420, 32/42/47/55LD520, 55LD520C
(For 55LD520C,
55LD520)
PREPARATION
x4
x4
(M4 x 14)
(M4 x 24)
Screws for stand assembly
(Refer to P.26)
(Except 47LD420,
47/55LD520, 55LD520C)
(For 55LD520C)
x2
Torx plus Star head screw
(Refer to P.26)
Screw for stand fixing
(Refer to P.33)
(For 55LD520C)
1.5V 1.5V
1,5Vcc 1,5Vcc
Protection Cover
(Refer to P.27)
Power Cord
Protective Bracket and Screw
for Power Cord (Refer to P.30)
32/37/42/47/55LE5300, 42/47/55LE7300, 42/47/55LE530C
(32/37/42/47/55LE5300, 42/47/55LE530C)
(32LE5300)
(37/42LE5300,
42LE530C)
x4
x4
(M4 x 22)
(M4 x 24)
(47/55LE5300,
47/55LE530C)
x4
x4
(M4 x 26)
(M4 x 16)
Screws for stand assembly
(Refer to P.22)
(42/47LE7300)
x3
(55LE7300)
x4
(M4 x 20) (M4 x 12)
x3
x4
(M4 x 26) (M4 x 16)
Screws for stand assembly
(Refer to P.21)
(For 42/47/55LE7300)
(For 32LE5300)
x2
Component gender Cable Management
Cable Holder
Clip
(Refer to p.31) cable, AV gender cable
(Refer to p.31)
10
(For 42/47/55LE530C)
x2
Screw for stand
fixing
(Refer to P.33)
Torx plus Star head
screw
(Refer to P.22)
FRONT PANEL INFORMATION
ꔛ
!
Image shown may differ from your TV.
! NOTE
►In case of some model, the thin film on screen is a part of TV, So don’t take it off.
19/22/26LE5300, 22/26LE5500
22/26LE5500, 42/47/55LE530C
PREPARATION
? 19/22/26/32/37/42/47/55LE5300,
?
Remote Control Sensor
Power/Standby Indicator
(Can be adjusted using the Power Indicator
in the OPTION menu.►p.111)
32/37/42/47/55LE5300, 42/47/55LE530C
SPEAKER
Remote Control Sensor
CH
VOL
VOL
ENTER
MENU
INPUT
Intelligent Sensor
Adjusts picture according to
the surrounding conditions
Power/Standby Indicator
(Can be adjusted using the Power Indicator
in the OPTION menu.►p.111)
ENTER
MENU
INPUT
19/22/26LE5300, 22/26LE5500
CH
VOL
ENTER
CHANNEL VOLUME
(-, +)
(ꕍ,ꕌ)
Buttons
Buttons
MENU
INPUT
ENTER MENU INPUT POWER
Button Button Button Button
32/37/42/47/55LE5300, 42/47/55LE530C
VOL
ENTER
CH
VOL
CHANNEL VOLUME
(-, +)
(ꕍ,ꕌ)
Buttons
Buttons
MENU
ENTER
MENU
INPUT
INPUT
ENTER MENU INPUT POWER
Button Button Button Button
11
PREPARATION
ꔛ
CH
CH
Image shown may differ from your TV.
VOL
PREPARATION
32/37/42/47LD450, 37/42/47LD450C, 42/47LD451C, 32/37/42/47LD452C,
ENTER 32/42/47LD452B
VOL
MENU
CH INPUT
CHANNEL
(ꕌ,ꕍ) Buttons
ENTER
SPEAKER
VOL
MENU
ENTER
MENU
INPUT
INPUT
Remote Control Sensor
Power/Standby Indicator
(Can be adjusted using the Power Indicator
in the OPTION menu.►p.111)
VOLUME (+, -)
Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
CH
CH
26LD352C
VOL
ENTER
VOL
MENU
CH
CHANNEL
(ꕌ,ꕍ) Buttons
VOL
VOLUME (+, -)
Buttons
INPUT
SPEAKER
ENTER
ENTER Button
MENU
ENTER
MENU Button
Remote Control Sensor
INPUT
Power/Standby Indicator
(Can be adjusted using the Power Indicator
in the OPTION menu.►p.111)
12
MENU
INPUT Button
INPUT
POWER Button
CH
CH
VOL
VOL
CHANNEL
(ꕌ,ꕍ) Buttons
PREPARATION
42/47/55LD630
VOLUME (+, -)
Buttons
ENTER
CH
MENU
INPUT
ENTER
ENTER Button
MENU
MENU Button
INPUT
SPEAKER
INPUT Button
VOL
POWER Button
ENTER
MENU
INPUT
Power/Standby Indicator
(Can be adjusted using the Power Indicator
in the OPTION menu.►p.111)
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to the surrounding conditions.
13
PREPARATION
ꔛ
Image shown may differ from your TV.
CH
PREPARATION
32/42/47LD420
VOL
CHANNEL
(▲,▼) Buttons
CH
ENTER
MENU
INPUT
VOLUME (+, -)
Buttons
VOL
SPEAKER
Remote Control Sensor
Power/Standby Indicator
(Can be adjusted using the Power Indicator
in the OPTION menu.►p.111)
ENTER
ENTER Button
MENU
MENU Button
INPUT
INPUT Button
POWER Button
CH
32/42/47/55LD520, 55LD520C
CH
VOL
ENTER
VOL
MENU
CHANNEL
(▲,▼) Buttons
INPUT
CH
SPEAKER
Remote Control Sensor,
Intelligent Sensor MENU
Adjusts picture according to
the surrounding conditions
INPUT
Power/Standby Indicator
(Can be adjusted using the Power Indicator in
the OPTION menu.►p.111)
14
VOLUME (+, -)
Buttons
ENTER
VOL
ENTER Button
ENTER
MENU Button
MENU
INPUT Button
INPUT
POWER Button
OFF
ON
OFF
ON
CH
CH
CHANNEL VOL
(▲,▼) Buttons
PREPARATION
42/47/55LE7300
ENTER
OFF
ON
VOL
VOLUME (+, -)
MENU
Buttons
INPUT
ENTER Button
Power/Standby Indicator
(Can be adjusted using the
Power Indicator in the OPTION
menu.►p.111)
ENTER
MENU
MENU Button
CH
INPUT Button
INPUT
POWER Button
VOL
Remote Control Sensor
!
Intelligent Sensor
Adjusts picture according to
the surrounding conditions.
?
! NOTE
►Do not step on the glass stand or subject it
to any impact.It may break, causing possible
? injury from fragments of glass, or the TV
may fall.
►Do not drag the TV. The floor or the product
may be damaged.
ENTER
MENU
INPUT
15
PREPARATION
BACK PANEL INFORMATION
IN 3
USB IN
USB IN
RS-232C IN
(CONTROL&SERVICE)
2
H/P
AV IN
VIDEO L(MONO) AUDIO R
Y
PB
PR
YVIDEO PB
L
AUDIO
L
PR
AUDIO
COMPONENT IN
VIDEO
R
/DVI IN
/DVI IN
1
1
2
(DVI)
9
ANTENNA/
7
(DVI)
1
CABLE IN
ANTENNA/
CABLE IN
R
COMPONENT IN
DC-IN
9
H/P
5
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
RGB IN (PC)
IN 3
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
DC-IN
8
RS-232C IN
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
IN 3
(DVI)
H/P
1
USB IN
2
8
USB IN
4
USB IN
3
H/P
DC-IN
2
USB IN
1
(DVI)
/DVI IN
DC-IN
1
/DVI IN
11
26LE5300,
26LE5500
H/P
H/P
IN 3
H/P
19/22LE5300,
22LE5500
H/P
PREPARATION
19/22/26LE5300, 22/26LE5500,
USB IN
Image shown may differ from your TV.
USB IN
ꔛ
6
2
RS-232C IN
RS-232C IN
(CONTROL&SERVICE)
(CONTROL&SERVICE)
OPTICAL
AV IN
AUDIO IN DIGITAL OPTICAL
AV IN
RGB/DVI AUDIO
AUDIOINOUT DIGITAL
L(MONO) AUDIO R
VIDEO
RGB/DVI AUDIO
OUT VIDEO L(MONO)
AUDIO R
Power Connection
RGB INRGB
(PC)IN (PC)
Y
PB
Y
VIDEO
PR
PB
VIDEO
L
PR
AUDIO
R
L
AUDIO
COMPONENT IN
COMPONENT IN
DC IN
!
!
?
?
Connect the AC/DC adapter plug to the
power input jack on the TV.
2 Connect the power cord to the AC/DC
adapter first, then plug the power cord into
the wall power outlet.
R
ANTENNA/
CABLEANTENNA/
IN 1
CABLE IN
AC/DC Adaptor
CAUTION
►Please be sure to connect the TV to the AC/DC power adapter before connecting the TV’s
power plug to a wall power outlet.
16
USB IN
IN 4
/DVI IN
H/P
LAN
AV IN2
VIDEO / AUDIO
COMPONENT IN2
Y PB PR / AUDIO
USB IN
8
AV IN 1
RGB IN (PC)
COMPONENT IN 1
1
Y
PB
PR
VIDEO
(RGB/DVI)
L
AUDIO
R
?
7
3
42/47/55LE7300
1
2
3
(CONTROL & SERVICE)
AV IN 1
RGB IN (PC)
VIDEO L/MONO AUDIO R
4 IN 1
COMPONENT
(DVI)
/DVI IN
ANTENNA/
CABLE IN
AUDIO IN
Y
(RGB/DVI)
OPTICAL
DIGITAL
AUDIO OUT
7
!
PB
RS-232C
IN
VIDEO
(CONTROL & SERVICE)
?
PR
L
AUDIO
L/MONO AUDIO R
VIDEO
5
For HDMI IN 4 and USB IN
►For an optimal connection,
HDMI cables and USB
devices should have bezels
less than 10 mm (0.39
inches) thick.
R
5
*A
2
AUDIO IN
(RGB/DVI)
WIRELESS
CONTROL
AV IN 1
RGB IN (PC)
1(DVI)
A
1
CAUTION
RS-232C IN
2
1
3
6
OPTICAL
DIGITAL
AUDIO OUT
/DVI IN
9
ANTENNA/
CABLE IN
AUDIO IN
(DVI)
!
5
VIDEO L/MONO AUDIO R
2
(
2
ꔡ
(CONTROL & SERVICE)
Y
PB
VIDEO
PR
L
AUDIO
R
10 mm (0.39 inches)
ANTENNA/
CABLE IN
COMPONENT IN 1
7
/DVI IN
3
IN 4
1
RS-232C IN
OPTICAL
DIGITAL
AUDIO OUT
LAN
AV IN2
VIDEO / AUDIO
3
4
H/P
/DVI IN
3
COMPONENT IN2
Y PB PR / AUDIO
2
1
WIRELESS
CONTROL
10
1
2
ꔡ
PREPARATION
32/37/42/47/55LE5300, 42/47/55LE530C
3
6
17
PREPARATION
32/42/47LD420, 32/37/42/47LD450, 42/47LD451C
AC IN
PREPARATION
USB IN
USB IN
10
IN 2
IN 3
AC IN
AVAV
IN 1IN 1
RGB
(PC)
RGB
IN IN
(PC)
L/MONO AUDIO R
VIDEO L/MONO
AUDIO R
VIDEO
2
1
1
Y
PB
PR
L
R
L
R
Y
PB
PR
AUDIO
AUDIO
VIDEO
AUDIO
IN INRGB IN (PC)
AUDIOVIDEO
VIDEO
(RGB/DVI)
(RGB/DVI)
COMPONENT IN
/DVI
/DVIIN
IN
5
RS-232C IN
(CONTROL & SERVICE)
OPTICAL
DIGITAL
AUDIO OUT
COMPONENT IN
AVAV
IN IN
2 2
AV IN
1
ANTENNA/
ANTENNA/
CABLE
L/MONO
AUDIO
R
CABLE
IN IN
USB IN
IN 2
RS-232C IN
RS-232C
(CONTROL
&IN
SERVICE)
(CONTROL
& SERVICE)
OPTICAL
OPTICAL
DIGITAL
DIGITAL
AUDIO
AUDIO
OUTOUT
8
1
H/P
4
9
VIDEO L/MONO AUDIO R
3
H/P
H/P
2
VIDEO L/MONO AUDIO R
VIDEO L/MONO AUDIO R
1
5
AV IN 2
1
AUDIO IN
(RGB/DVI)
/DVI IN
Y
7
PB
VIDEO
PR
L
6
AUDIO
R
COMPONENT IN
ANTENNA/
CABLE IN
32/42/47/55LD520, 55LD520C, 42/47/55LD630
USB IN
USB IN
10
1
1
/DVI IN
OPTICAL
DIGITAL
AUDIO OUT
Y
AUDIO
IN
/DVI IN
(RGB/DVI)
RGB IN (PC)
RS-232C IN
PB
YL
PR
AUDIO IN
VIDEO
(RGB/DVI)
COMPONENT IN
VIDEO
PBR
VIDEO
AUDIO
L
R
PR
ANTENNA/AUDIO
CABLE IN
COMPONENT
IN
AV IN 1
L/MONO AUDIO R
7
6
1
18
AUDIO IN
(RGB/DVI)
Y
PB
VIDEO
PR
COMPONENT IN
L
AUDIO
R
ANTENNA/
CABLE IN
IN 3
AV IN 2
USB IN
IN 3
H/P
ANTENNA/
CABLE IN
IN 3
IN 3
AV IN 2
(CONTROL & SERVICE)
2
/DVI IN
5
VIDEO L/MONO AUDIO R
L/MONO AUDIO R
8
1
1
9
H/P
2
VIDEO
8
9
VIDEO L/MONO AUDIO R
2
L/MONO AUDIO R
VIDEO
(CONTROL & SERVICE)
AV IN 1
AV IN 1
RGB IN (PC)
RGB IN (PC)
RS-232C IN
RS-232C IN
OPTICAL (CONTROL & SERVICE)
DIGITAL
AUDIO OUT
OPTICAL
DIGITAL
AUDIO OUT
USB IN
4
H/P
3
VIDEO L/MONO AUDIO R
2
VIDEO L/MONO AUDIO R
1
H/P
32/42/47/55LD520,
55LD520C
42/47/55LD630
5
AV IN 2
5
AV IN 2
37/42/47LD450C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C
AC IN
4
DIGITAL
AUDIO OUT
/DVI IN
RGB IN (PC)
RGB IN (PC)
1
2
1
(CONTROL & SERVICE)
AV IN 1
VIDEO L/MONO
REMOTE
CONTROL IN
RJP
13
12
AVAV
IN IN
2 2
1 OPTICAL
DIGITAL
3
AUDIO IN
(RGB/DVI)
AUDIO IN
(RGB/DVI)
RJP
EXTERNAL SPEAKER OUT
AV IN 1
PB
PVIDEO
R
L
R R
L
R
AUDIO
L/MONO
ANTENNA/
L
R
PBCOMPONENT
PR
IN
ANTENNA/
CABLE IN
AUDIO
VIDEO
CABLE IN
COMPONENT IN
RGB IN (PC)
Y
Y
OPTICAL AUDIO IN
DIGITAL (RGB/DVI)
AUDIO OUT
HDMI/DVI IN, HDMI IN
Digital Connection.
Supports HD video and Digital audio. Doesn’t
support 480i.
Accepts DVI video using an adapter or HDMI
to DVI cable (not included).
2 RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin
cable (VGA cable).
AUDIO IN (RGB/DVI)
0.32 cm (1/8 inch) headphone jack for analog
PC audio input.
3 OPTICAL DIGITAL AUDIO OUT
Digital optical audio output for use with amps
and home theater systems.
Note: In standby mode, this port doesn’t work.
4 RS-232C IN (CONTROL & SERVICE)
Used by third party devices.
This port is used for service or Hotel mode.
5 AV (Audio/Video) IN
Analog composite connection. Supports standard definition video only (480i).
6 ANTENNA/CABLE IN
Connect over-the-air or cable signals to this
jack.
1
RS-232C IN
(CONTROL & SERVICE)
/DVI IN
/DVI IN AUDIO OUT
EXTERNAL
SPEAKER OUT
AV
IN 1
L
R
AUDIO R
L/MONO AUDIO R
VIDEO
VIDEO L/MONO AUDIO R
VIDEO L/MONO AUDIO R
RS-232C IN
REMOTE
OPTICAL
CONTROL
IN
7Y
PB
PR
L
COMPONENT IN 6
R
8
IN 2
5
11
1
VIDEO L/MONO AUDIO R
2
H/P
1
USB IN
IN 2
IN 3
USB IN
USB IN
AC IN
PREPARATION
10
5
AV IN 2
ANTENNA/
CABLE IN
COMPONENT IN
Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video &
red and white for audio.
8 USB INPUT
Used for viewing videos, photos and listening
to MP3s.
7
HEADPHONE
0.32 cm (1/8 inch) headphone jack
Impedance 16 Ω , Maximum audio out 15 mW
10 Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on
DC pwer.
9
11 REMOTE
CONTROL IN
For a wired remote control.
12 EXTERNARL SPEAKER OUT
For use with external speakers.
13 RJP
Connect this to an LG remote jack pack system.
19
PREPARATION
STAND INSTRUCTIONS (For 19/22LE5300, 22LE5500)
ꔛ
Image shown may differ from your TV.
DETACHMENT
INSTALLATION
PREPARATION
1
Carefully place the TV screen side down
on a cushioned surface to protect the
screen from damage.
2
Assemble the parts of the STAND BODY
with the STAND BASE of the TV.
STAND BODY
1
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
2
Remove the screws from the TV.
3
Detach the stand from TV.
STAND BASE
3
4
Assemble the TV as shown.
Install the 4 screws into the holes shown.
M4 x 14
!
?
20
! NOTE
►When assembling the desk type stand,
make sure the screws are fully tightened (If
not tightened fully, the TV can tilt forward
? after the product installation). Do not over
tighten.
STAND INSTRUCTIONS (For 42/47/55LE7300)
ꔛ
Image shown may differ from your TV.
INSTALLATION
DETACHMENT
Carefully place the TV screen side down
on a cushioned surface to protect the
screen from damage.
2
Assemble the parts of the STAND BODY
with the STAND BASE of the TV.
STAND BODY
1
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
2
Remove the screws from the TV.
3
Detach the stand from TV.
PREPARATION
1
M4 x 20
42/47LE7300
M4 x 26
55LE7300
3
4
STAND BASE
Assemble the TV as shown.
Install the 4 screws into the holes shown.
M4 x 12
42/47LE7300
M4 x 16
55LE7300
!
?
! NOTE
►When assembling the desk type stand,
make sure the screws are fully tightened (If
not tightened fully, the TV can tilt forward
? after the product installation). Do not over
tighten.
21
PREPARATION
STAND INSTRUCTIONS
(For 26/32/37/42/47/55LE5300, 26LE5500, 42/47/55LE530C)
ꔛ
Image shown may differ from your TV.
PREPARATION
INSTALLATION
1
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
2
Assemble the parts of the STAND BODY
with the STAND BASE of the TV.
M4 x 20
M4 x 22
M4 x 24
M4 x 26
26LE5300,
26LE5500
32LE5300
37/42LE5300,
42LE530C
47/55LE5300,
47/55LE530C
3
Assemble the TV as shown.
4
Assemble the part of the STAND
REAR COVER with the TV.
5
STAND BODY
STAND BASE
STAND REAR
COVER
Install the 4 screws into the holes shown.
or
(For 42/47/55LE530C)
Tighten the two of these four
screws and the two Torx plus
star head screws (provided as
parts of the TV) to secure the TV. Tighten
the two Torx plus star head screws with a
star head driver bit (not provided as parts
of the TV).
x2
22
x2
!
! NOTE
?
►When assembling the desk type stand,
make sure the screws are fully tightened (If
? not tightened fully, the TV can tilt forward
after the product installation). Do not over
tighten.
M4 x 14
M4 x 16
26LE5300,
26LE5500
Other models
1
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
2
Remove the screws from the TV.
3
Detach the STAND REAR COVER from TV.
4
Detach the stand from TV.
PREPARATION
DETACHMENT
23
PREPARATION
STAND INSTRUCTIONS
(For 32/37/42/47LD450, 37/42/47LD450C, 42/47/55LD630, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C)
ꔛ
Image shown may differ from your TV.
PREPARATION
INSTALLATION
1
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
AC IN
CABLE MANAGEMENT
AC IN
2
Assemble the parts of the STAND BODY
with the STAND BASE of the TV.
STAND BODY
M4X20
M4 x 20
STAND BASE
AC IN
CABLE MANAGEMENT
AC IN
3
Assemble the TV as shown.
CABLE MANAGEMENT
AC IN
4
Install the 4 screws into the holes shown.
CABLE MANAGEMENT
AC IN
CABLE MANAGEMENT
M4 x 20
24
!
! NOTE
?
►When assembling the desk type stand,
make sure the screws are fully tightened (If
? not tightened fully, the TV can tilt forward
after the product installation). Do not over
tighten.
1
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
AC IN
CABLE MANAGEMENT
PREPARATION
DETACHMENT
AC IN
2
Remove the screws from the TV.
CABLE MANAGEMENT
AC IN
CABLE MANAGEMENT
3
Detach the stand from TV.
AC IN
AC IN
CABLE MANAGEMENT
CABLE MANAGEMENT
PROTECTION COVER
After removing the stand, install the included
PROTECTION COVER over the hole for the
stand.
Press the PROTECTION COVER into the TV until
you hear it click.
When installing the wall mounting bracket, use
the PROTECTION COVER.
25
AC IN
PREPARATION
STAND INSTRUCTIONS
(For 32/42/47LD420, 32/42/47/55LD520, 55LD520C)
ꔛ
Image shown may differ from your TV.
PREPARATION
INSTALLATION
1
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
2
(For 55LD520C, 55LD520)
Assemble the parts of the STAND BODY
with the STAND BASE of the TV.
STAND BODY
M4 x 14
3
Assemble the TV as shown.
4
Install the 4 screws into the holes shown.
M4X20
STAND BASE
M4 x 24
For 55LD520C
x4
26
!
! NOTE
?
►When assembling the desk type stand,
make sure the screws are fully tightened (If
? not tightened fully, the TV can tilt forward
after the product installation). Do not over
tighten.
Tighten the stand with the four screws
(provided as parts of the TV).
or
Tighten the two of these four
screws and the two Torx plus
star head screws (provided as
parts of the TV) to secure the TV. Tighten
the two Torx plus star head screws with a
star head driver bit (not provided as parts
of the TV).
x2
x2
ꔛ
Image shown may differ from your TV.
1
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
2
Remove the screws from the TV.
3
Detach the stand from TV.
PREPARATION
DETACHMENT
PROTECTION COVER
After removing the stand, install the included
PROTECTION COVER over the hole for the
stand.
Press the PROTECTION COVER into the TV until
you hear it click.
When installing the wall mounting bracket, use
the PROTECTION COVER.
27
PREPARATION
VESA WALL MOUNTING
PREPARATION
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.
VESA (A * B)
Model
19LE5300,
22LE5300,
22LE5500,
26LE5300,
26LE5500
32LE5300,
32LD420,
32LD450,
32LD520,
32LD452C,
32LD452B,
26LD352C
37LE5300, 37LD450,
37LD450C, 37LD452C,
42LE5300, 42LE530C,
42LE7300, 42LD450,
42LD450C, 42LD420,
42LD520, 42LD630,
42LD451C, 42LD452C,
42LD452B, 47LE5300,
47LE530C, 47LE7300,
47LD450, 47LD450C,
47LD420, 47LD520,
47LD630, 47LD451C,
47LD452C, 47LD452B
55LE5300,
55LE530C,
55LE7300,
55LD520,
55LD520C,
55LD630
28
B
A
Standard
Screw
Quantity
Wall Mounting Bracket
(sold separately)
LSW100B, LSW100BG
100 * 100
M4
4
LSW100B, LSW100BG
200 * 100
M4
4
LSW200B, LSW200BG
200 * 200
M6
4
LSW400B, LSW400BG,
DSW400BG
400 * 400
M6
4
!
!
?
►Screw length needed depends on the wall
mount used. For further information, refer to
? the instructions included with the mount.
►Standard dimensions for wall mount kits are
shown in the table.
►When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.
►Do not use screws longer than the standard
dimension, as they may cause damage to the
inside to the TV.
►For wall mounts that do not comply with the
VESA standard screw specifications, the length
! of the screws may differ depending on their
specifications.
►Do not use screws that do not comply with the
VESA standard screw specifications.
Do not use fasten the screws too strongly, this
may damage the TV or cause the TV to a fall,
leading to personal injury. LG is not liable for
these kinds of accidents.
►LG is not liable for TV damage or personal
injury when a non-VESA or non specified wall
mount is used or the consumer fails to follow
the TV installation instructions.
PREPARATION
?
! NOTE
?
CAUTION
►Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to
electric shock.
For 26LE5300, 26LE5500
Place the ring spacers on the set before installing the wall
mounting bracket so that the inclination of the backside
of the set can be adjusted perpendicularly.
4-RING SPACERS
29
PREPARATION
CABLE MANAGEMENT
ꔛ
Image shown may differ from your TV.
PREPARATION
32/37/42/47LD450, 37/42/47LD450C, 32/42/47LD420, 32/42/47/55LD520, 55LD520C,
42/47/55LD630, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C
1
Connect the cables as necessary.
To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section.
For 37/42/47LD450C, 55LD520C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C:
Secure the power cord with the PROTECTIVE BRACKET/SCREW on the TV back cover. It will
help prevent the power cable from being removed by accident.
PROTECTIVE BRACKET/SCREW
2
Open the CABLE MANAGEMENT CLIP as shown.
CABLE MANAGEMENT CLIP
3
30
Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed.
19/22/26LE5300, 22/26LE5500
After connecting the cables as necessary,
install the CABLE HOLDER as shown
and bundle the cables.
FOR DESK-TYPE STAND
1
CABLE HOLDER
CABLE MANAGEMENT CLIP
32/37/42/47/55LE5300, 42/47/55LE530C
1
Secure the power cord with the CABLE
HOLDER on the TV back cover.
It will help prevent the power cable from
being removed by accident.
Install the CABLE MANAGEMENT CLIP
as shown.
PREPARATION
1
42/47/55LE7300
2
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
FOR WALL MOUNT
CABLE HOLDER
2
After connecting the cables as necessary,
install the CABLE HOLDER as shown
and bundle the cables.
1
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install CABLE HOLDER as shown and
bundle the cables.
CABLE HOLDER
CABLE HOLDER
31
PREPARATION
DESKTOP PEDESTAL INSTALLATION
ꔛ
Image shown may differ from your TV.
For proper ventilation, allow a clearance of 10.1 cm (4 inch) on all four sides from the wall.
PREPARATION
10.1 cm (4 inch)
!
!
?
?
10.1 cm (4 inch)
10.1 cm (4 inch)
10.1 cm (4 inch)
CAUTION
►Ensure adequate ventilation by following the clearance recommendations.
►Do not mount near or above any type of heat source.
SWIVEL STAND (Except 19/22LE5300, 22LE5500)
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 º to suit
your viewing position.
KENSINGTON SECURITY SYSTEM
ꔛ
This feature is not available for all models.
-T
he TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security
System cable as shown below.
- For the detailed installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington
Security System.
For further information, contact http://www.kensington.com,
the internet homepage of the Kensington company. Kensington
sells security systems for expensive electronic equipment such
as notebook PCs and LCD projectors.
NOTE: The Kensington Security System is an optional accessory.
32
ATTACHING THE TV TO A DESK
(For 32/42LD420, 32/37/42LD450, 37/42LD450C, 32/42LD520, 42LD630, 32LE5300,
42LD451C, 32/37/42LD452C, 32/42LD452B, 26LD352C)
ꔛ
Image shown may differ from your TV.
Stand
PREPARATION
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
1-Screw
(provided as parts of the product)
Desk
For 37/42/47LD450C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C
Stand
4-Screws
(not provided as parts of the product)
For 55LD520C
Desk
!
4-Screws
(not provided as parts of the product)
!
►Recommended screw size: M5 x L (*L: Table depth + 8~10 mm)
?
?
ex) Table depth: 15mm, Screw: M5 x 25
WARNING
►To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
33
PREPARATION
SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND
You should purchase necessary components to prevent the TV from tipping over (when not using a
wall mount).
ꔛ Image shown may differ from your TV.
ꔛ
PREPARATION
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward
direction, potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
ꔛ
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the
picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the
bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket
that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
ꔛ
!
?
34
Use a sturdy rope (sold separately) to tie the product. It is safer to tie the
rope so it becomes horizontal between the wall and the product.
! NOTE
►Use a platform or cabinet strong enough and large enough to support the size and weight of
the TV.
►
T
? o use the TV safely make sure that the height of the bracket on the wall and the one on the TV are
the same.
IN 4
H/P
ANTENNA OR CABLE CONNECTION
1
IN 4
(SERVICE ONLY)
VIDEO L(MONO) AUDIO R
AUDIO IN AUDIO OUT
AC IN
2
/DVI IN
Y
CONTROL
CABLE MANAGEMENT
PB
PR
R
L
1
AUDIO
VIDEO
ANTENNA/
CABLE IN
VIDEO L/MONO AUDIO R H/P
Multi-family Dwellings/Apartments
ꔡ
(Connect to wall antenna
socket)
WIRELESS
RS-232C IN
AV IN 1 COMPONENT IN
IN (PC)
Wall Antenna Socket or Outdoor Antenna without a Cable RGB
Box
Connections.
3
LAN
RGB/DVI OPTICAL DIGITAL
For optimum picture quality, adjust antenna direction if2 needed.
PREPARATION
USB IN 1
AV IN 2
1. Antenna (Analog or Digital)
Wall
Antenna
Socket
L/MONO AUDIO R
CABLE MANAGEMENT
USB INVIDEO
2
AC IN
To prevent damage do not connect to the power outlet until all connections are made between the
devices.
ꔛ Image shown may differ from your TV.
ꔛ
AV IN 2
Outdoor
Antenna
(VHF, UHF)
RF Coaxial Wire (75 Ω)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
LAN
WIRELESS
CONTROL
(SERVICE ONLY)
RGB/DVI OPTICAL DIGITAL
VIDEO L(MONO) AUDIO R
AUDIO IN AUDIO OUT
2
/DVI IN
Y
PB
PR
L
R
1
VIDEO
AUDIO
AV IN 1 COMPONENT IN
2. Cable
1
RS-232C IN
Be careful not to bend the copper wire
when connecting the antenna.
3
2
ꔡ
Copper Wire
RGB IN (PC)
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RF Coaxial Wire (75 Ω)
ꔛ
ꔛ
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
For much more information about antennas visit our Knowledgebase at http://lgknowledgebase.
com. Search for antenna.
35
EXTERNAL
EXTERNALEQUIPMENT
EQUIPMENT
SETUP
SETUP
ꔛ
To prevent the equipment damage, never plug in any power cords until you have finished connecting all
equipment.
ꔛ
IThis part of EXTERNAL EQUIPMENT SETUP mainly use picture of for 26LE5300/26LE5500.
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box.
However, if you do receive digital signals from a digital set-top box or other digital external device.
Component Connection
Connect the video outputs (Y, PB, PR) of the
digital set-top box to the COMPONENT IN
VIDEO or 1/2* jacks on the TV. Match the jack
colors (Y = green, PB = blue, and PR = red).
2
Connect the audio output of the digital set-top
box to the COMPONENT IN AUDIO or 1/2*
jacks on the TV.
Y
DC-IN
1
PB
PR
R
2
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital settop box operation.)
ꔛ Select the Component or Component1/2* input
source on the TV using the INPUT button on the
remote control.
* Component2: For 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
L
1
2
(DVI)
2. How to use
AV IN
VIDEO L(MONO) AUDIO R
ꔛ
RGB IN (PC)
Y
1280x720p
1920x1080i
1920x1080p
59.94
15.73
60.00
31.47
59.94
31.50
60.00
44.96
59.94
45.00
60.00
33.72
59.94
33.75
60.00
26.97
23.976
27.00
24.00
33.71
29.97
33.75
30.00
67.432
59.94
67.50
60.00
/DVI IN
USB IN
15.73
L
AUDIO
R
ANTENNA/
CABLE IN
2
RS-232C IN
(CONTROL&SERVICE)
For 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
IN 4
Vertical
Frequency(Hz)
PR
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
R
ANTENNA/
CABLE IN
COMPONENT IN
AV IN2
VIDEO / AUDIO
720x480p
Horizontal
Frequency(kHz)
1
(DVI)
H/P
720x480i
DC-IN
COMPONENT IN2
Y PB PR / AUDIO
Resolution
PB
VIDEO
COMPONENT IN
Y, CB/PB, CR/PR
36
/DVI IN
1
2
1
HDMI OUTPUT
PR
DC-IN
/DVI IN
EXTERNAL EQUIPMENT SETUP
1. How to connect
1
(DVI)
2
PB
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
Y
R
L
/DVI
DC-IN
1
2
(DVI)
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
PR
VIDEO
L
AUDIO
R
ANTENNA/
CABLE IN
COMPONENT IN
HDMI Connection
1
DC-IN
1
(DVI)
2
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
No separate audio connection is necessary.
HDMI supports both audio and video.
AV IN
VIDEO L(MONO) AUDIO R
1
RGB IN (PC)
Y
2. How to use
PB
VIDEO
PR
L
AUDIO
R
COMPONENT IN
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital settop box.)
ꔛ Select the HDMI1, HDMI2, HDMI3*, or HDMI4**
input source on the TV using the INPUT button
on the remote control.
* HDMI3: For 26LE5300, 26LE5500, 32/42/47/55LD520,
55LD520C, 42/47/55LD630
** HDMI4: For 32/37/42/47/55LE5300, 42/47/55LE7300,
42/47/55LE530C
ꔛ ! NOTE
?
►If an HDMI cable doesn’t support High Speed HDMI,
it can cause flickers or no screen display. In this case
? use the latest cables that support High Speed HDMI.
►HDMI Audio Supported Format: Dolby Digital (32 kHz, 44.1
kHz, 48 kHz), Linear PCM (32 kHz, 44.1 kHz, 48 kHz)
DC-IN
/DVI IN
!
HDMI OUTPUT
1
(DVI)
2
EXTERNAL EQUIPMENT SETUP
2
Connect the digital set-top box to HDMI/DVI IN
1, 2, 3*, or 4** jack on the TV.
/DVI IN
1. How to connect
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
COMPONENT IN
R
ANTENNA/
CABLE IN
HDMI-DTV
Resolution
720x480p
1280x720p
1920x1080i
1920x1080p
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.47
59.94
31.50
60.00
44.96
59.94
45.00
60.00
33.72
59.94
33.75
60.00
26.97
23.976
27.00
24.00
33.71
29.97
33.75
30.00
67.432
59.94
67.50
60.00
L
AUDIO
R
DVI OUTPUT
37
Y
PB
VIDEO
PR
L
AUDIO
R
COMPONENT IN
ANTENNA/
CABLE IN
EXTERNAL EQUIPMENT SETUP
HDMI OUTPUT
1. How to connect
DC-IN
EXTERNAL EQUIPMENT SETUP
1
/DVI IN
DVI to HDMI Connection
1
(DVI)
2
RS-232C IN
(CONTROL&SERVICE)
Connect the DVI output of the digital set-top
box to the HDMI/DVI IN 1 or 2* jack on the TV.
2
Connect the digital set-top box audio output to
the AUDIO IN (RGB/DVI) jack on the TV.
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO1 L(MONO) AUDIO R
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
COMPONENT IN
2. How to use
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital settop box.)
ꔛ 2
Select the HDMI1 or HDMI2* input source on the
TV using the INPUT button on the remote control.
ꔛ * HDMI2: For 32/42/47/55LD520, 55LD520C, 42/47/55LD630
L
38
!
! NOTE
?
►A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio
? connection is necessary.
AUDIO
R
DVI OUTPUT
R
ANTENNA/
CABLE IN
DVD SETUP
Component Connection
1. How to connect
2
Connect the audio outputs of the DVD to the
COMPONENT IN AUDIO or 1/2* jacks on the
TV.
Y
DC-IN
2. How to use
/DVI IN
Connect the video outputs (Y, PB, PR) of the
DVD to the COMPONENT IN VIDEO or 1/2*
jacks on the TV. Match the jack colors (Y =
green, PB = blue, and PR = red).
1
PB
1
2
(DVI)
PR
R
2
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
Turn on the DVD player, insert a DVD.
ꔛ Select the Component or Component1/2* input
source on the TV using the INPUT button on the
remote control.
ꔛ Refer to the DVD player’s manual for operating
instructions.
L
EXTERNAL EQUIPMENT SETUP
1
ꔛ
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
PR
VIDEO
L
AUDIO
R
ANTENNA/
CABLE IN
COMPONENT IN
Component Input ports
DC-IN
To get better picture quality, connect a DVD
player to the component input ports as shown
below.
USB IN
For 32/37/42/47/55LE5300,
AV IN
42/47/55LE7300, 42/47/55LE530C
Y
PR
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
PR
L
AUDIO
R
COMPONENT IN
ANTENNA/
CABLE IN
2
HDMI OUTPUT
DC-IN
/DVI IN
PB
Y
PB
VIDEO
AV IN2
VIDEO / AUDIO
Y
VIDEO L(MONO) AUDIO R
RGB IN (PC)
1
(DVI)
2
PR
1
PB
Y
RS-232C IN
R
L
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
COMPONENT IN
B IN
PR
RS-232C IN
(CONTROL&SERVICE)
IN 4
PB
2
H/P
Video output ports
on DVD player
Y
1
(DVI)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
COMPONENT IN2
Y PB PR / AUDIO
Component ports on
the TV
/DVI IN
*C
omponent2: For 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
R
ANTENNA/
CABLE IN
39
CABLE IN
COMPONENT IN
EXTERNAL EQUIPMENT SETUP
HDMI OUTPUT
1. How to connect
1
EXTERNAL EQUIPMENT SETUP
Connect the AUDIO/VIDEO jacks between TV
and DVD. Match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red)
DC-IN
2. How to use
Turn on the DVD player, insert a DVD.
ꔛ Select the AV or AV1/2* input source on the TV
using the INPUT button on the remote control.
ꔛ Refer to the DVD player's manual for operating
instructions.
/DVI IN
Composite (RCA) Connection
1
(DVI)
2
RS-232C IN
(CONTROL&SERVICE)
Y
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
PB
PR
L
R
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
ꔛ
PB
VIDEO
PR
L
AUDIO
R
ANTENNA/
CABLE IN
DC-IN
/DVI IN
COMPONENT IN
1
2
(DVI)
1
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
* AV2: Except 19/22/26LE5300, 22/26LE5500
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
VIDEO
HDMI Connection
L
R
Y
PB
PR
AUDIO
VIDEO
L
AUDIO
R
ANTENNA/
CABLE IN
COMPONENT IN
1
Connect the HDMI output of the DVD to the
HDMI/DVI IN 1, 2, 3*, or 4** jack on the TV.
DC-IN
2
/DVI IN
1. How to connect
1
(DVI)
2
RS-232C IN
(CONTROL&SERVICE)
No separate audio connection is necessary.
HDMI supports both audio and video.
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
1
RGB IN (PC)
2. How to use
Y
PB
PR
VIDEO
L
AUDIO
R
COMPONENT IN
Select the HDMI1, HDMI2, HDMI3*, or HDMI4** input
source on the TV using the INPUT button on the
remote control.
ꔛ Refer to the DVD player's manual for operating
instructions.
* HDMI3: For 26LE5300, 26LE5500, 32/42/47/55LD520,
55LD520C, 42/47/55LD630
** HDMI4: For 32/37/42/47/55LE5300, 42/47/55LE7300,
42/47/55LE530C
ANTENNA/
CABLE IN
ꔛ
?
40
! NOTE
►If an HDMI cable doesn’t support High Speed HDMI,
it can cause flickers or no screen display. In this case
? use the latest cables that support High Speed HDMI.
►HDMI Audio Supported Format: Dolby Digital (32 kHz, 44.1
kHz, 48 kHz), Linear PCM (32 kHz, 44.1 kHz, 48 kHz)
DC-IN
/DVI IN
!
HDMI OUTPUT
1
(DVI)
2
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
COMPONENT IN
R
ANTENNA
CABLE I
VCR SETUP
1. How to connect
2
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AV IN
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT1 VIDEO 2 L(MONO) AUDIO R
(DVI)
Connect the RF antenna outDC-INsocket
RGB IN (PC)
of the VCR to the ANTENNA/CABLE
Y
P
VIDEO
IN socket on the TV.
PR
B
RS-232C IN
(CONTROL&SERVICE)
1
OPTICAL
AV IN
AUDIO
IN RDIGITAL
L
ANTENNA/
RGB/DVI AUDIO OUT
VIDEO L(MONO) AUDIO R
AUDIO
CABLE IN
COMPONENT IN
2
RGB IN (PC)
Connect the antenna cable to the RF
antenna in socket of the VCR.
Y
PB
PR
VIDEO
L
AUDIO
R
COMPONENT IN
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
VIDEO
ANTENNA/
CABLE IN
L
AUDIO
ANT OUT
Wall JackANT IN
2
2. How to use
Set VCR output switch to 3 or 4 and
then tune TV to the same channel number.
ꔛ Insert a video tape into the VCR and
press PLAY on the VCR (Refer to the
VCR owner’s manual).
R
S-VIDEO
OUTPUT
SWITCH
ꔛ
Antenna
VIDEO
EXTERNAL EQUIPMENT SETUP
1
1
(DVI)
/DVI IN
DC-IN
/DVI IN
Antenna Connection
L
AUDIO
Composite (RCA) Connection
1
(DVI)
2
Connect the AUDIO/VIDEO jacksDC-INbetween TV
and VCR. Match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red)
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AV IN
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT1 VIDEO 2 L(MONO) AUDIO R
(DVI)
DC-IN
2. How to use
/DVI IN
1
/DVI IN
1. How to connect
RGB IN (PC)
Y
Insert a video tape into the VCR and press PLAY
on the VCR. (Refer to the VCR owner’s manual.)
ꔛ Select the AV or AV1/2* input source on the TV
using the INPUT button on the remote control.
ꔛ PB
VIDEO
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AV IN
AUDIO
IN RDIGITAL
L
ANTENNA/
RGB/DVI AUDIO OUT
VIDEO L(MONO) AUDIO R
AUDIO
PR
CABLE IN
COMPONENT IN
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
COMPONENT IN
R
ANTENNA/
CABLE IN
1
* AV2: Except 19/22/26LE5300, 22/26LE5500
!
?
! NOTE
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
►If you have a mono VCR, connect the audio cable
from the VCR to the AUDIO L(MONO) jack of the TV.
?
VIDEO
L
R
AUDIO
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
L
R
AUDIO
41
R
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
1
EXTERNAL EQUIPMENT SETUP
Connect the AUDIO/VIDEO jacks
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
2. How to use
Select the AV or AV1/2* input source on
the TV using the INPUT button on the
remote control.
ꔛ Operate
the corresponding external
equipment.
ꔛ
DC-IN
/DVI IN
1. How to connect
1
(DVI)
2
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
R
COMPONENT IN
ANTENNA/
CABLE IN
1
* AV2: Except 19/22/26LE5300, 22/26LE5500
VIDEO
L
R
Video Game Set
Camcorder
42
USB CONNECTION
1. How to connect
2. How to use
ꔛ
After connecting the USB IN jack, you
or
Memory Key
H/P
IN 3
use the USB function. (►p.78)
EXTERNAL EQUIPMENT SETUP
Connect the USB device to the USB
IN jack on the side of TV.
USB IN
1
HEADPHONE SETUP
(Except 37/42/47LD450C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C)
You can listen to the sound through the headphone.
!
?
1
Plug the headphone into the headphone socket.
2
To adjust the headphone volume,
press the VOL +/- button. If you
press the MUTE button, the sound
from the headphone is switched off.
H/P
1. How to connect
! NOTE
►AUDIO menu options are disabled when connecting a
headphone.
►
? When changing AV MODE with a headphone connected, the change is applied to video but not to audio.
►Optical Digital Audio Out is not available when connecting a headphone.
43
EXTERNAL EQUIPMENT SETUP
AUDIO OUT CONNECTION
1. How to connect
EXTERNAL EQUIPMENT SETUP
DC-IN
1
1
(DVI)
2
Connect one end of the optical cable to the
TV port of OPTICAL DIGITAL AUDIO OUT.
2
Connect the other end of the optical cable to
the digital audio input on the audio equipment.
3
Set the “TV Speaker option - Off” in the
AUDIO menu. (►p.119). See the external audio
equipment instruction manual for operation.
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
1
RGB IN (PC)
Y
PB
VIDEO
!!
!! NOTE
??
►When connecting with external audio equipment, such
as amplifiers or speakers, you can turn the TV speakers
?? off in the menu. (►p.119)
►Do not look into the optical output port. Looking at
the laser beam may damage your vision.
►Audio with ACP (Audio Copy Protection) function may
block digital audio output.
PR
L
AUDIO
COMPONENT IN
2
CAUTION
44
/DVI IN
Send the TV’s audio to external audio equipment via the Audio Output port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL
AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
R
ANTENNA/
CABLE IN
PC SETUP
VGA (D-Sub 15 Pin) Connection
DC-IN
/DVI IN
This TV provides Plug and Play capability, meaning that a PC adjusts automatically to the TV’s settings.
1
2
(DVI)
2
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Connect the VGA output of the PC to the
RGB IN (PC) jack on the TV.
Y
PB
PR
VIDEO
L
AUDIO
COMPONENT IN
Connect PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
2. How to use
1
2
RGB OUTPUT
AUDIO
Turn on the PC and the TV.
ꔛ Select the RGB-PC input source on the TV using
the INPUT button on the remote control.
DC-IN
/DVI IN
ꔛ
1
(DVI)
2
R
EXTERNAL EQUIPMENT SETUP
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
1. How to connect
1
RS-232C IN
(CONTROL&SERVICE)
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
COMPONENT IN
R
ANTENNA/
CABLE IN
45
AUDIO
DVI OUTPUT
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
RGB OUTPUT
AUDIO
EXTERNAL EQUIPMENT SETUP
1
Connect the DVI output of the PC to the
HDMI/DVI IN 1 or 2* jack on the TV.
2
Connect the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
2. How to use
Turn on the PC and the TV.
ꔛ Select the HDMI1 or HDMI2* input source on the
TV using the INPUT button on the remote control.
DC-IN
/DVI IN
1. How to connect
1
(DVI)
2
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
RGB IN (PC)
Y
ꔛ
PB
VIDEO
PR
L
AUDIO
COMPONENT IN
1
2
* HDMI2: For 32/42/47/55LD520, 55LD520C, 42/47/55LD630
AUDIO
46
AV IN
VIDEO L(MONO) AUDIO R
DVI OUTPUT
R
ANTENNA/
CABLE IN
!
?
! NOTE
►To get the the best picture quality, adjust the PC graphics card to 1360 x 768 (19/22/26LE5300,
22/26LE5500, 32LD452C, 32LD452B, 26LD352C) or 1920 x 1080 (Other models).
►In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
►Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become
permanently imprinted on the screen.
►The synchronization input form for Horizontal and Vertical frequencies is separate.
►Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly.
►When selecting HDMI-PC, set the “Input Label - PC” in the OPTION menu.
EXTERNAL EQUIPMENT SETUP
?
►Depending
on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.
Supported Display Specifications (RGB-PC, HDMI-PC)
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
640x350
31.468
70.09
720x400
31.469
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1280x768
47.776
59.87
1360x768
47.712
60.015
1280x1024
63.981
60.02
1600x1200
75.00
60.00
Except 19/22/26LE5300,
22/26LE5500, 32LD452C,
32LD452B, 26LD352C
1920x1080
RGB-PC
66.587
59.934
Except 32/37/42/47/55LE5300,
42/47/55LE7300, 42/47/55LE530C
1920x1080
HDMI-PC
67.50
60.00
47
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
EXTERNAL EQUIPMENT SETUP
You can choose the resolution in RGB-PC mode.
The Position, Phase, and Size can also be adjusted.
You can choose this option only when the PC resolution is set to 1024X768, 1280X768 or 1360X768.
PICTURE
ꔂ Move
ꔉ Enter
SCREEN
Resolution
• Brightness
50
• Sharpness
70
• Color
60
• Tint
0
R
G
• Color Temp.
0
W
C
• Advanced Control
• Picture Reset
Auto Config.
• Screen (RGB-PC)
Position
Size
ꔠ
ꔉ
Phase
Reset
1
2
3
4
5
48
MENU
Select PICTURE.
ENTER
Select Screen (RGB-PC).
ENTER
Select Resolution.
ENTER
Select the desired resolution.
ENTER
ꔂ Move
ꔑ 1024 x 768
□ 1280 x 768
□ 1360 x 768
� Prev.
Auto Configure
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image
is still not correct, try using the manual settings or a different resolution or refresh rate on the PC.
ꔂ Move
SCREEN
ꔉ Enter
ꔂ Move
� Prev.
Resolution
• Brightness
50
• Sharpness
70
• Color
60
• Tint
0
R
G
• Color Temp.
0
W
C
• Advanced Control
• Picture Reset
Auto Config.
• Screen (RGB-PC)
Position
Size
ꔠ
ꔉ
Auto Config.
Yes
No
Phase
Reset
1
2
3
4
5
MENU
Select PICTURE.
ENTER
Select Screen (RGB-PC).
ENTER
Select Auto Config..
ENTER
Select Yes.
ENTER
EXTERNAL EQUIPMENT SETUP
PICTURE
If the position of the image is still not
correct, try Auto adjustment again.
ꔛ If picture needs to be adjusted again
after Auto adjustment in RGB-PC,
you can adjust the Position, Size or
Phase.
ꔛ
Start Auto Configuration.
49
EXTERNAL EQUIPMENT SETUP
Adjustment for screen Position, Size, and Phase
If the picture is not clear after auto adjustment or if text is shaking, adjust the picture phase manually.
This feature operates only in RGB-PC mode.
EXTERNAL EQUIPMENT SETUP
PICTURE
ꔂ Move
ꔉ Enter
SCREEN
ꔂ Move
� Prev.
Resolution
• Brightness
50
• Sharpness
70
• Color
60
• Tint
0
R
G
• Color Temp.
0
W
C
• Advanced Control
• Picture Reset
Auto Config.
• Screen (RGB-PC)
Position
◀
▲
▼
▶
Size
ꔠ
ꔉ
Phase
Reset
1
2
3
4
5
50
MENU
Select PICTURE.
ENTER
Select Screen (RGB-PC).
ENTER
Select Position, Size, or Phase.
ENTER
Make appropriate adjustments.
ENTER
Position: This function is to adjust
picture to left/right and up/down as
you prefer.
ꔛ Size: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal screen size will also change.
ꔛ Phase: This function allows you to
remove any horizontal noise and
clear or sharpen the image of characters.
ꔛ
Screen Reset (Reset to original initial values)
Returns Position, Size, and Phase to the default initial settings.
This feature operates only in RGB-PC mode.
ꔂ Move
ꔉ Enter
SCREEN
ꔂ Move
� Prev.
Resolution
• Brightness
50
• Sharpness
70
• Color
60
• Tint
0
R
G
• Color Temp.
0
W
C
• Advanced Control
• Picture Reset
Auto Config.
• Screen (RGB-PC)
Position
Size
ꔠ
ꔉ
Phase
To Set
Yes
No
EXTERNAL EQUIPMENT SETUP
PICTURE
Reset
1
2
3
4
5
MENU
Select PICTURE.
ENTER
Select Screen (RGB-PC).
ENTER
Select Reset.
ENTER
Select Yes.
ENTER
Start Reset.
51
WATCHING
WATCHING TVTV
/ CHANNEL
/ CHANNEL
CONTROL
CONTROL
REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
The remote control may differ from the images below.
POWER
Turns the TV on from standby or off
to standby.
ENERGY SAVING
Adjusts the Energy Saving setting.
►p.104
WATCHING TV / CHANNEL CONTROL
AV MODE
INPUT
ENERGY AV MODE INPUT
TV
TV
Toggles through preset Video and
Audio modes. ►p.75
Rotates through inputs.
Also switches the TV on from standby. ►p.70
Returns to the last TV channel.
SAVING
1
2
3
4
5
6
NUMBER button
7
8
9
- (DASH)
0
FLASHBK
LIST
MARK
FAV
VOL
RATIO
CH
INFO
LIST
FLASHBK
MUTE
MENU
P
A
G
E
Used to enter a program number for
multiple program channels such as
5-1, 5-2, etc.
Displays the channel table.
►p.67
TV
SAVING
1
2
3
4
5
6
7
8
9
0
FLASHBK
LIST
VOL
FAV
PORTAL
CH
MUTE
MENU
VOLUME UP/
DOWN
MARK
FAV
Tunes to the last channel viewed.
Q.MENU
ENTER
ENERGY AV MODE INPUT
GUIDE
Q.MENU
Adjusts the volume.
ENTER
Set up desired favorite channels list
►p.66
BACK
EXIT
MARK
Select the input to apply the Picture
Wizard settings. ►p.103
Use to mark or unmark a photo/
music/movie. ►p.83, 88, 94
RATIO
Changes the aspect ratio.
PORTAL
MUTE
52
►p.100
Displays and removes hotel interactive
menu. (Other models)
Displays the interactive menu, make
click on EXIT key if you want to
remove the menu window. (For
32/42/47LD452B)
Switches the sound on or off.
►p.54
CHANNEL
UP/DOWN
Changes the channel.
PAGE
UP/DOWN
Moves from one full set of screen
information to the next one.
RETURN
RATIO
INFO
EXIT
P
A
G
E
Displays the main menu or clears all
on-screen displays and return to TV
viewing.
GUIDE
Displays the program event according to time scheduler.
Q.MENU
Opens the list of Quick Menu
options. ►p.59
THUMBSTICK
(Up/Down/
Left
Right/ENTER)
Navigates the on-screen menus and
adjusts the system settings to your
preference.
BACK or
RETURN
Allows the user to move return one
step in an interactive application or
other user interaction function.
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
8
9
0
FLASHBK
LIST
MARK
FAV
VOL
RATIO
CH
P
A
G
E
MUTE
MENU
INFO
Q.MENU
INFO
Displays the information of watching
program.
SIMPLINK
See a list of AV devices connected
to TV.
When you toggle this button, the
SIMPLINK menu appears at the
screen. ►p.76
ENTER
BACK
EXIT
EXIT
Clears all on-screen displays and
return to TV viewing.
COLOR
BUTTON
Access special functions in some
menus.
USB,
SIMPLINK
Control buttons
• Controls MY MEDIA menu
(Photo List, Music List, Movie List)
• Controls the SIMPLINK compatible devices.
SIMPLINK
See a list of AV devices connected
to TV.
When you toggle this button, the
SIMPLINK menu appears at the
screen. ►p.76
RATIO
Installing Batteries
Changes the aspect ratio.
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
8
9
0
FLASHBK
LIST
MARK
FAV
VOL
CH
PORTAL
MUTE
MENU
GUIDE
Q.MENU
ENTER
RETURN
INFO
EXIT
P
A
G
E
WATCHING TV / CHANNEL CONTROL
MENU
RATIO
►p.100
ꔛ
Open the battery compartment cover on the back
side and install the batteries matching correct polarity.
ꔛ
Install two 1.5V AAA batteries. Don’t mix old or used
batteries with new ones.
ꔛ
Close cover.
53
WATCHING TV / CHANNEL CONTROL
TURNING ON THE TV
1
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
In standby mode to turn TV on, press the / I, INPUT, CH (ꕌ or ꕍ) button on the TV or press
the , INPUT, CH (ꕌ or ꕍ), Number (0-9) button on the remote control.
ꔛ
WATCHING TV / CHANNEL CONTROL
!
2
Select the viewing source by using the INPUT button on the remote control.
3
When finished using the TV, press the POWER button on the remote control. The TV reverts
to standby mode.
! NOTE
►If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
?
►If you do not complete the Initial setting, it will appear whenever the TV is switched on until the
? Initial setting procedure is completed.
CHANNEL SELECTION
1
Press the CH (ꕌor ꕍ) or NUMBER buttons to select a channel number.
VOLUME ADJUSTMENT
Adjust the volume to suit your personal preference.
54
1
Press the VOL (+ or -) button to adjust the volume.
2
If you want to switch the sound off, press the MUTE button.
3
You can cancel the Mute function by pressing the MUTE or VOL (+ or -) button.
INITIAL SETTING
This Function guides the user to easily set the essential items for viewing the TV for the first time
when purchasing the TV. It will be displayed on the screen when turning the TV on for the first time. It
can also be activated from the user menus.
Default selection is “Home Use”. We recommend setting the TV to “Home Use” mode for the best
picture in your home environment.
ꔛ “Store Demo” Mode is only intended for use in retail environments. Customers can adjust the
“Picture menu - Picture mode” manually while inspecting the TV, but the TV will automatically
return to preset in-store mode after 5 minutes.
ꔛ “Store Demo” Mode is an optimal setting for displaying at stores. “Store Demo” mode initializes
the TV to set the image quality.
ꔛ
1
WELCOME!
Select Menu Language.
Thank you for choosing LG
Step 1. Language
2
English
ENTER
Español
Français
한국어
WATCHING TV / CHANNEL CONTROL
Step 1. Selecting Language
ꔉ Next
Step 2. Mode setting
Step 2. Mode Setting
i Selecting the environment.
Choose the setting mode you want.
Select [Home Use] when setting TV up
in-home. You can adjust picture quality
accordingly through Picture Mode menu
option.
Home Use
• Demo Mode
ꕉ Previous
1
2
Select Home Use.
ENTER
Store Demo
Off
ꔉ Next
For 19/22/26/32/37/42/47/55LE5300,
22/26LE5500, 42/47/55LE7300,
37/42/47LD450C, 55LD520C,
32/42/47/55LD520, 42/47/55LD630,
42/47/55LE530C, 32/37/42/47LD452C,
32/42/47LD452B, 26LD352C
55
WATCHING TV / CHANNEL CONTROL
Step 3. Power Indicator (For LED LCD TV)
1
Step 3. Power Indicator
Standby Light
◀
Off
ꕉ Previous
▶
2
ꔉ Next
Select On or Off.
ENTER
WATCHING TV / CHANNEL CONTROL
ꔛ
This function is disable in “Step2. Mode
Setting - Store Demo”.
Step 4. Time Zone
1
Select Time Zone option.
Step 4. Time Zone
Time Zone
◀
Daylight Saving
Eastern
▶
Auto
ꕉ Previous
ꔉ Next
2
3
Select Daylight Saving
option.
ENTER
Step 5. Auto Tuning
Step 5. Auto Tuning
1
Before starting,
be sure that the
TV antenna is connected.
ꕉ Previous
56
ꔉ Next
ENTER
Check your antenna connection and
start Auto Tuning.
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
1
2
3
MENU
Display each menu.
ENTER
Select a menu item.
CHANNEL
EXIT
ꔂ Move
Return to TV viewing.
PICTURE
ꔉ Enter
• Auto Tuning
• Aspect Ratio
• Manual Tuning
• Picture Wizard
• Channel Edit
PICTURE
AUDIO
AUDIO
4
Accept the current selection.
ꔂ Move
• Auto Volume
: Off
• Clear Voice II
: Off �3
ꔉ Enter
ꔂ Move
ꔉ Enter
: 16:9
• ꕊ Energy Saving : Off
• Picture Mode
: Standard
• Backlight
70
• Contrast
100
• Brightness
50
• Sharpness
70
TIME
ꔂ Move
ꔉ Enter
ꔂ Move
ꔉ Enter
• Clock
• Balance
0
L
R
TIME
• Sound Mode
: Standard
• Infinite Sound: Off
• Treble
50
• Bass
50
• Reset
• Off Time
: Off
• On TIme
: Off
• Sleep Timer
: Off
• Auto Off
: On
WATCHING TV / CHANNEL CONTROL
CHANNEL
ENTER
For 37/42/47LD450C, 55LD520C,
42/4755LE530C,
32/37/42/47LD452C,
32/42/47LD452B, 26LD352C
For USA
LOCK
ꔂ Move
OPTION
ꔉ Enter
• Language
• Set Password
LOCK
• Lock System
: On
• Block Channel
• Movie Rating
• TV Rating-Children
• TV Rating-General
• Downloadable Rating
• Input Block
• Caption
: Off
• Power Indicator
OPTION
• Initial Setting
• Set ID
:1
• Mode Setting
: Home Use
For Canada
• Set Password
• Lock System
: On
• Block Channel
• TV Rating-English
• TV Rating-French
• Downloadable Rating
• Input Block
• Key Lock
: Off
57
WATCHING TV / CHANNEL CONTROL
i.e)
Input List
ꔂ Move
WATCHING TV / CHANNEL CONTROL
TV
USB
HDMI2
HDMI3
AV
Component
RGB-PC
HDMI1
ꔅ Input Label
� Exit
INPUT
MY MEDIA
MY MEDIA
EzSign TV
Movie List
Photo List
Music List
Extra Contents
For 32/42/47LD452B Except 32/42/47LD420,
32/37/42/47LD450,
37/42/47LD450C,
32/42/47/55LD520,
55LD520C,
42/47/55LE530C,
42/47LD451C,
32/37/42/47LD452C,
32/42/47LD452B,
26LD352C
58
ꔉ Enter
For 32/37/42/47LD452C
QUICK MENU
our TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Y
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
◀
Aspect Ratio
16:9 �
ꔣAspect Ratio: Selects your desired picture format.
ꕇPicture Mode: Selects the desired preset picture setting.
ꕈ Sound Mode: Selects the desired preset sound setting.
ꔴ Multi Audio: Changes the audio language (Digital signal).
ꔴ SAP: Selects MTS sound (Analog signal).
ꔤSleep Timer: Select the amount of time before your TV
turns off automatically.
ꔳDel/Add: Select channel you want to add or delete.
ꕄCaption: Select on or off.
ꔢUSB Device: Select “Eject” in order to eject a USB device.
ꕉ Exit
1
2
Q.MENU
Display each menu.
ENTER
Make appropriate adjustments.
3
EXIT
WATCHING TV / CHANNEL CONTROL
A
▶
Return to TV viewing.
59
WATCHING TV / CHANNEL CONTROL
CUSTOMER SUPPORT
Picture Test / Sound Test
This function is a customer support function that can execute picture and sound tests.
ꔑ Picture Test
□ Sound Test
WATCHING TV / CHANNEL CONTROL
□ Product/Service Info.
Yes
No
Close
□ Picture Test
ꔑ Sound Test
? Do you have a sound problem in this
screen?
□ Product/Service Info.
Close
1
MENU
2
3
4
RETURN
EXIT
60
? Do you have a problem in this test
screen?
RED
Select Customer Support.
ENTER
Select Picture Test or Sound Test.
ENTER
Select Yes.
or
BACK
Return to the previous menu.
Return to TV viewing.
Yes
No
Product/Service Info.
This function shows support and product information.
Customer Service Center can differ by country.
□ Picture Test
□ Sound Test
ꔑ Product/Service Info.
1
MENU
2
3
RETURN
EXIT
RED
Select Customer Support.
ENTER
Select Product/Service Info..
You can check the various
product/Service infomation
based on your model.
or
BACK
Return to the previous menu.
WATCHING TV / CHANNEL CONTROL
Close
Return to TV viewing.
61
WATCHING TV / CHANNEL CONTROL
SIMPLE MANUAL (Except 32/37/42/47LD452C, 32/42/47LD452B)
You can easily and effectively access the TV information by viewing a simple manual on the TV.
During the Simple Manual operation, audio will be muted.
1
MENU
2
WATCHING TV / CHANNEL CONTROL
62
GREEN
Select Simple Manual.
Select the part of the manual you would like to see.
RED
Go to the Index page.
BLUE
Play the Simple Manual automatically or manually.
EXIT
Return to TV viewing.
3
CHANNEL SETUP
Auto Scan (Auto Tuning)
Automatically finds all channels available through antenna or cable inputs, and stores them in memory
on the channel list.
Run this function if you change your residence or move the TV.
Auto Tuning memorizes only the channels available at the time.
ꔂ Move
ꔉ Enter
• Auto Tuning
ꔉ
ꔡ
• Manual Tuning
• Channel Edit
CHANNEL
ꔂ Move
ꔉ Enter
• Auto Tuning
• Manual Tuning
• Channel Edit
Antenna
Cable
Check your antenna connection.
The previous channel information
will be updated during Auto Tuning.
Start
Close
1
2
3
4
MENU
Select CHANNEL.
ENTER
Select Auto Tuning.
ENTER
Select Start.
Run Auto tuning.
ENTER
5
RETURN
EXIT
or
BACK
WATCHING TV / CHANNEL CONTROL
CHANNEL
The TV will ask for a password if
parental control has been activated
(LOCK Menu). Use the password you
set up in the LOCK Menu to allow a
channel search.
ꔛ The maximum number of channels
the TV can store is 1000.
ꔛ Found channels are grouped in the
order of DTV, TV, Cable DTV and
Cable TV.
ꔛ
Return to the previous menu.
Return to TV viewing.
63
WATCHING TV / CHANNEL CONTROL
Add/Delete Channel (Manual Tuning)
When selecting DTV or Cable DTV input signal in Manual Tuning, you can view the on-screen signal
strength monitor to see the quality of the signal being received.
WATCHING TV / CHANNEL CONTROL
CHANNEL
ꔉ Enter
• Auto Tuning
CHANNEL
• Auto Tuning
ꔉ
ꔀ
• Manual Tuning
• Channel Edit
• Manual Tuning
• Channel Edit
ꔂ Move
ꔉ Enter
◀
▶
DTV
Select channel type and RF-channel
number.
2
Channel
DTV 2-1
• Signal Strength
• Signal Quality
88%
88%
Delete
Close
1
2
3
MENU
Select CHANNEL.
ENTER
Select Manual Tuning.
ENTER
Select DTV, TV, Cable DTV,
or Cable TV.
4
Select channel you want to
add or delete.
5
Select Add or Delete.
ENTER
6
RETURN
EXIT
64
ꔂ Move
or
BACK
Return to the previous menu.
Return to TV viewing.
The TV will ask for a password if
parental control has been activated
(LOCK Menu). Use the password you
set up in the LOCK Menu to allow a
channel search.
ꔛ The maximum number of channels
the TV can store is 1000.
ꔛ
Channel Editing
The channels in the Channel Edit List are displayed in black and the channels deleted from the Channel
Edit List are displayed in blue.
When a channel number is deleted, it means that you will be unable to select it using CH∧∨button
during TV viewing. If you wish to select the deleted channel, directly enter the channel number with the
NUMBER buttons or select it in the Channel Edit menu.
ꔂ Move
• Auto Tuning
3
MENU
Select CHANNEL.
ENTER
Select Channel Edit.
ENTER
Select a channel.
4
EXIT
5-1
7-1
ꔉ CH.Change
ꘂ Favorite Ch.
ꔂ Navigation
ꘃ Page Change
ꔛ
� Favorite Ch. Group
ꕉ Previous
ꔅ Block/Unblock
ꔅ Add/Delete
Keep pressing the ꕌ button and use
the < or > buttons to move between
DTV, TV, Cable DTV and Cable TV.
Switch to the chosen channel number.
ENTER
Move the pages when the channel list is
too long.
P
A
G
E
RETURN
Cable TV
Block or unblock the channel.
You can block/unblock channels even if
you select “Lock system-Off” in the
LOCK menu.
YELLOW
5
Page 1/1
Cable DTV
Add or delete a channel.
BLUE
CH
A
TV
ꔠ
ꔉ
• Channel Edit
2
DTV
3-1
• Manual Tuning
1
Favorite Group :
ꔉ Enter
WATCHING TV / CHANNEL CONTROL
Channel Edit
CHANNEL
or
BACK
Return to the previous menu.
Return to TV viewing.
65
WATCHING TV / CHANNEL CONTROL
FAVORITE CHANNEL SETUP
Favorite Channels are a convenient feature that lets you quickly select channels of your choice without
waiting for the TV to select all the in-between channels.
Favorite List
◀
ꕉ Exit
▶
WATCHING TV / CHANNEL CONTROL
3-1
DTV
4-1
P
A
G
E
CH
ꔊꔋFavorite Ch. Group
Group A
DTV
1
2
MARK
FAV
ꔉ
3
ꔅ Ch.Edit
2
3
4
5
6
7
1
8
9
Select your desired channel.
0
ꔡ
ꔅ Ch.Reg.
or
Select your desired favorite
channel group from A to D.
YELLOW
Register or cancel the current channel
in favorite channel list.
BLUE
Go to the “CHANNEL menu - Channel
Edit”.
4
Return to TV viewing.
EXIT
ꔛ
You can also setup Favorite List in the
CHANNEL menu - Channel Edit.
FAVORITE CHANNEL LIST
Favorite List
◀
ꕉ Exit
ꔊꔋFavorite Ch. Group
▶
Group A
DTV
3-1
DTV
4-1
Displaying the favorite channel list
1
MARK
FAV
ꔉ
ꔡ
Selecting a channel in the favorite
channel list
1
2
ꔅ Ch.Reg.
Display the Favorite channel list.
ꔅ Ch.Edit
Select a channel.
ENTER
Switch to the chosen channel number.
Paging through a favorite channel
list
1
CH
2
EXIT
66
P
A
G
E
Turn the pages.
Return to TV viewing.
CHANNEL LIST
You can check which channels are stored in the memory by displaying the channel list.
Channel List
DTV
3-1
DTV
4-1
ꕉ Exit
ꔒ
ꔉ
ꔡ
This padlock is displayed
when the channel is locked
with parental control.
Displaying Channel List
1
Display the Channel List.
LIST
BLUE
Tune to the “CHANNEL menu - Channel
Edit”.
WATCHING TV / CHANNEL CONTROL
ꔅ Ch.Edit
Selecting a channel in the channel list
1
2
Select a channel.
ENTER
Switch to the chosen channel number.
Paging through a channel list
1
CH
2
EXIT
P
A
G
E
Turn the pages.
Return to TV viewing.
67
WATCHING TV / CHANNEL CONTROL
CHANNEL INFORMATION
ꔖ DTV 8-1 CNN
Brief Info Title Test...
WATCHING TV / CHANNEL CONTROL
68
ꔀ Ch. Change
10:10 AM
▶ Next
11:40 AM ꔥ Multilingual ꔨ ꔯ Caption ꔷ 1080i ꔒ TV-PG D L S V
No information
Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking,
with regular and special guests.
Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking,
�
Displaying Channel Information
1
INFO
2
Show the current channel program Information
on the screen.
Show a previous or next channel’s program information
3
EXIT
Return to TV viewing.
ꔉ Watch
ꔅ Up
ꔅ Down
CHANNEL BRIEF INFORMATION
Brief Info shows the present screen information.
1
2
ENTER
Shows the current channel’s brief info screen.
ENTER
Return to TV viewing.
3
8-1
ꔖ DTV
1
4
Brief Info Title Test...
10:10 AM
ꘋꔫ
CNN
5
Sun, Feb 21, 2010 10: 40 AM
11:40 AM ꔥ Multilingual ꔨ ꔯ Caption ꔷ 1080i ꔒ TV-PG D L S V
Next - 11:40 AM
News
ꔥ
Multilingual : The program contains two or more audio services. Use the Q.MENU menu to select wanted Audio.
ꔯ
Caption : The program contains one or more caption services.
Use the Q.MENU menu to select wanted Closed caption.
ꔨ
Dolby Digital: The program contains a Dolby Digital audio
signal in TV and HDMI input source.
ꔶ
The original aspect ratio of the video is 4:3
ꔷ
The original aspect ratio of the video is 16:9 (wide)
480i
480p
720p
1080i
1080p
ꔒ
The
The
The
The
The
video
video
video
video
video
resolution
resolution
resolution
resolution
resolution
2
is
is
is
is
is
1
Program title
2
Day, Month, Year,
Present time
3
Program start time
4
Program progress
WATCHING TV / CHANNEL CONTROL
6
bar
5
Program finish
time
6
Banner information
720x480i
720x480p
1280x720p
1920x1080i
1920x1080p
V-Chip: The program contains V-Chip information. Refer to
the LOCK menu: A (Age), D (Dialogue), L (Language), S (Sex),
V (Violence), FV (Fantasy Violence)
69
WATCHING TV / CHANNEL CONTROL
INPUT LIST
Only these input signals which are connected to a TV can be activated and selected.
i.e)
Input List
WATCHING TV / CHANNEL CONTROL
1
ꔂ Move
TV
USB
HDMI2
HDMI3
INPUT
ENTER
AV
Component
RGB-PC
HDMI1
� Input Label
ꕉ Exit
ꔉ Enter
Disconnected inputs are inactive
(grayed out)
Select the desired input source.
When new external device is connected, this popup
menu is displayed automatically.
If selecting Yes, you can select input source that you
want to appreciate.
ꔛ But, when selecting “SIMPLINK - On”, popup menu for
HDMI input will not be displayed.
ꔛ
AV
TV: Select it to watch over-the-air, cable and digital cable broadcasts.
ꔛ AV: Select them to watch a VCR or other external equipment.
ꔛ Component: Select them to watch DVD or a Digital set-top box.
ꔛ RGB-PC: Select it to view PC input.
ꔛ HDMI: Select them to watch high definition devices.
ꔛ
70
New external input is connected.
Do you want to use this?
Yes
No
INPUT LABEL
This indicates which device is connected to which input port.
i.e)
ie) C
hange the input label using Blue
button
i.e)
Input List
Input Label
◀
Component
◀
▶
RGB-PC
◀
▶
HDMI2
◀
▶
HDMI1
◀
▶
VCR
▶
ꔍ
TV
USB
HDMI2
HDMI3
AV
Component
RGB-PC
HDMI1
� Input Label
ꕉ Exit
Close
1
2
Select the desired input
source.
INPUT
Select the label.
BLUE
3
RETURN
EXIT
ꔉ Enter
WATCHING TV / CHANNEL CONTROL
AV
ꔂ Move
or
BACK
Return to the previous menu.
Return to TV viewing.
71
WATCHING TV / CHANNEL CONTROL
RESET TO FACTORY DEFAULT (INITIAL SETTING)
This function resets the TV to factory default and erases all stored channels.
OPTION
ꔂ Move
ꔉ Enter
• Language
• Caption
WATCHING TV / CHANNEL CONTROL
3
4
72
• Caption
ꔉ
ꔀ
• Initial Setting
!
• Set ID
:1
• Set ID
:1
• Mode Setting
: Home Use
• Mode Setting
: Home Use
MENU
Select OPTION.
ENTER
Select Initial Setting.
ENTER
Select Yes.
ENTER
ꔉ Enter
: Off
• Power Indicator
• Initial Setting
2
ꔂ Move
• Language
: Off
• Power Indicator
1
OPTION
TV turns off automatically and starts
factory reset.
All user settings
and channel settings will
ꔀ
ꔉ
be reset. Still continue?
Yes
No
When selecting “Lock System - On”
in the LOCK menu, the message to
enter the password appears.
ꔛ If you forget your password, press
“0-3-2-5” on the remote control.
ꔛ
MODE SETTING
Default selection is “Home Use”. We recommend setting the TV to “Home Use” mode for the best
picture in your home environment.
OPTION
ꔂ Move
ꔉ Enter
• Language
OPTION
ꔂ Move
• Language
• Caption
: Off
• Caption
• Power Indicator
i Selecting the environment.
Choose the setting mode you want.
: Off
• Power Indicator
• Initial Setting
• Initial Setting
:1
• Mode Setting
: Home Use
ꔠ
ꔉ
• Set ID
:1
• Mode Setting
: Home Use
Select [Home Use] when setting TV up
in-home. You can adjust picture quality
accordingly through Picture Mode menu
option.
Home Use
Store Demo
• Demo Mode
Off
Close
For 19/22/26/32/37/42/47/55LE5300,
22/26LE5500, 42/47/55LE7300,
37/42/47LD450C, 55LD520C,
32/42/47/55LD520, 42/47/55LD630,
42/47/55LE530C,
32/37/42/47LD452C,
32/42/47LD452B, 26LD352C
1
2
3
MENU
Select OPTION.
ENTER
Select Mode Setting.
ENTER
Select Home Use.
4
RETURN
EXIT
or
BACK
Return to the previous menu.
“Store Demo” Mode is only intended
for use in retail environments.
Customers can adjust the “Picture
menu - Picture mode” manually while
inspecting the TV, but the TV will
automatically return to preset instore mode after 5 minutes.
ꔛ “Store Demo” Mode is an optimal
setting for displaying at stores. “Store
Demo” mode initializes the TV to set
the image quality.
ꔛ
WATCHING TV / CHANNEL CONTROL
• Set ID
ꔉ Enter
Return to TV viewing.
73
WATCHING TV / CHANNEL CONTROL
DEMO MODE
Displays a slide show to explain the various feature of this TV.
OPTION
ꔂ Move
ꔉ Enter
OPTION
• Language
• Caption
• Language
: Off
• Caption
WATCHING TV / CHANNEL CONTROL
• Power Indicator
: Off
ꔉ Enter
i Selecting the environment.
Choose the setting mode you want.
• Power Indicator
• Initial Setting
• Initial Setting
• Set ID
:1
• Mode Setting
: Home Use
ꔠ
ꔉ
Select [Store Demo] for in-store dsplay. For use
in-home, select [Home Use].
• Set ID
:1
• Mode Setting
: Store Demo
Home Use
Store Demo
• Demo Mode
Off
Close
1
2
3
MENU
Select OPTION.
ENTER
Select Mode Setting.
ENTER
Select Store Demo.
4
ENTER
5
EXIT
74
ꔂ Move
Select On.
Return to TV viewing.
After a while, Demo Mode. starts.
If you want to stop the demo, press any
button (Except VOL +, - and MUTE button).
AV MODE
AV Mode toggles through preset Video and Audio settings.
AV MODE
2
ENTER
Cinema
Game
Sport
Press the AV MODE button repeatedly to
select the desired source.
If you select “Cinema” in AV mode,
Cinema will be selected both for
“PICTURE menu - Picture Mode”
and “AUDIO menu - Sound Mode”
respectively.
ꔛ If you select “Off” in AV mode, the
“Picture Mode” and “Sound Mode”
return to previous selected value.
ꔛ Off: Disables the AV MODE.
ꔛ Cinema: Optimizes video and audio
for watching movies.
ꔛ Sport: Optimizes video and audio for
watching sports events.
ꔛ Game: Optimizes video and audio for
playing games.
When playing a video game using
PlayStation or Xbox, it is recommended to use the Game mode.
When in Game mode, functions
related to picture quality will be optimized for playing games.
ꔛ
WATCHING TV / CHANNEL CONTROL
1
Off
75
WATCHING TV / CHANNEL CONTROL
SIMPLINK
SIMPLINK allows you to control and play other AV devices connected with HDMI cable without additional cables and settings. This TV may work with devices with HDMI-CEC support, but only devices
with the
logo are fully supported.
SIMPLINK can be turned on and off in the user menus.
1
ꔉ Enter ꕉ Exit
WATCHING TV / CHANNEL CONTROL
76
◀
On
2
Watch TV
◀ DISC 1
▶
◀ VCR 1
▶
HDD/DVD-R
HD HT
TV Speaker
Select On.
3
HDD Recorder
◀ Speaker
Display SIMPLINK menu.
▶
Select the desired device.
ENTER
4
Control connected AV devices.
ENTER
▶
TV viewing: Switch to the previous TV
channel regardless of the current
mode.
2 DISC playback: Select and play discs.
When multiple discs are available, the
disc devices are conveniently displayed
at the bottom of the screen.
3 VCR playback: Control the connected
VCR.
4 HDD Recordings playback: Control
recordings stored in HDD.
5 Audio Out to Home Theater speaker/
Audio Out to TV: Select Home Theater
speaker or TV speaker for Audio Out.
1
ꔉ Enter ꕉ Exit
◀
1
On
▶
Watch TV
2
◀ DISC 1
▶
►When no device is connected (displayed in gray)
3
◀ VCR 1
▶
►Selected Device
HDD/DVD-R
HD HT
4
HDD Recorder
5
◀ Speaker
TV Speaker
▶
►When a device is conected (displayed in bright
color)
SIMPLINK Functions
Direct Play: After connecting AV devices to the TV, you can directly control the devices and play media
without additional settings.
ꔛ Select AV device: Enables you to select one of the AV devices connected to the TV.
ꔛ
Disc playback: Control connected AV devices by pressing the ꕌꕍ< >, ENTER, ꕖ, ꕗ, ꕘ, ꕚ and ꕙ buttons.
ꔛ Power off all devices: When you power off the TV, all connected devices are turned off.
ꔛ Switch audio-out: Offers an easy way to switch audio-out.
ꔛ Sync Power on: When the equipment with Simplink function connected HDMI terminal starts to play,
The TV will automatically turn on.
Note: To operate SIMPLINK, an HDMI cable over Version 1.3 with *CEC function should be used. (*CEC:
Consumer Electronics Control).
(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does
not provide this function)
ꔛ
?
! NOTE
►Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of
the SIMPLINK device with the HDMI cable
?
►When
you switch the Input source with the INPUT button on the remote control, the SIMPLINK
device will stop.
►When you select a device with home theater functionality, the sound output automatically switches
to the home theater speakers and the TV speakers are turned off.
►If a connected SIMPLINK home theater system doesn’t play the audio from the TV, connect the
DIGITAL AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the
back of the SIMPLINK device with an OPTICAL cable.
WATCHING TV / CHANNEL CONTROL
!
77
MY
MY MEDIA
MEDIA
CONNECTION METHOD
USB Connection
USB IN
1 Connect the USB device to the USB IN jack on the side of TV.
H/P
MY MEDIA
IN 3
Memory Key
Precautions when using the USB device
►Only a USB storage device is recognizable.
►Connecting a USB storage device through a USB hub is not supported.
►A USB storage device which uses its own driver may not be recognized.
►The recognition speed of a USB storage device may depend on each device.
► Please do not turn off the TV or unplug the USB device when the connected USB storage device
is working. When such device is suddenly separated or unplugged, the stored files or the USB
storage device may be damaged.
►Only use a USB storage device which has normal music files, image files, or movie files.
►Please use only a USB storage device which was formatted as a FAT 32 or NTFS file system provided with the Windows operating system. Others may not be recognized.
►Some USB storage devices require a power adapter. The power adapter must be connected in
order to be seen by the TV.
►If a device is not recognized by the TV, try a different cable. Excessively long cables are not supported.
►Some USB storage devices may not be supported or operate properly.
►Please backup important files because data on USB device could be damaged. Data management
is consumer's responsibility and as a result, the manufacturer does not cover data damage.
►If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can
use up to 4 partitions or USB memory devices.
►In case of USB storage devices formatted as NTFS, deletion is not supported.
►File alignment method of USB storage device is similar to Window XP and file names can be up
to 100 English characters.
►The recommended capacity is 1TB or less for a USB external hard disk and 32 GB or less for USB
memory.
►If a USB external hard disk with a “Energy Saving” function doesn’t work, turn the hard disk off and
on again to make it work properly. Refer to the user manual of the USB external hard disk.
►USB storage devices below USB 2.0 are supported as well. But they may not work properly in the
movie list.
78
ENTRY MODE
The My Media menu will open automatically when you insert a USB drive. My Media can also be
accessed by choosing My Media in the user menu.
On USB device, you can not add a new folder or delete the existing folder.
MY MEDIA
EzSign TV
Movie List
Photo List
Music List
Extra Contents
1
2
3
MENU
SelectMY MEDIA.
ENTER
SelectEzSign TV,Movie
List, Photo List or Music List
or Extra Contents.
ENTER
ꔛ
MY MEDIA
For32/42/47LD452B Except32/42/47LD420, For32/37/42/47LD452C
32/37/42/47LD450,
37/42/47LD450C,
32/42/47/55LD520,
55LD520C,
42/47/55LE530C,
42/47LD451C,
32/37/42/47LD452C,
32/42/47LD452B,
26LD352C
ThisTVcanviewJPGimagefiles,HDDivX
filesorplayMP3audiofiles.
When removing the USB device
SelecttheUSB Devicemenubefore
removingtheUSBdevice.
1
2
Q.MENU
ENTER
SelectUSB Device.
SelectEject.
79
MY MEDIA
MOVIE LIST
(Except 32/42/47LD420, 32/37/42/47LD450, 37/42/47LD450C, 32/42/47/55LD520, 55LD520C,
42/47/55LE530C, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C)
The movie list is activated once a USB drive is detected. It is used when playing movie files on the TV.
It displays all of the video files it recognizes.
The On-Screen Display on your model may be slightly different.
MY MEDIA
Supported movie file
ꔛ Resolution: under 1920 pixel (width) x 1080 pixel (height)
ꔛ Frame Rate: under 30 frame/sec (1920x1080), under 60 frame/sec (1280x720)
ꔛ Max bitrate of playable video file: 20 Mbps (Mega bit per second)
ꔛ Bit rate : within 32 kbps to 320 kbps (MP3)
ꔛ Supported external subtitle format: *.smi/*.srt/*.sub (MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*.txt
(TMPlayer)/*.psb (PowerDivX)
ꔛ Supported Internal subtitle format: only, XSUB (It is the subtitle format used in DivX6 files)
Precautions when playing the video files
►Some user-created subtitles may not work properly.
►Some special characters are not supported in subtitles.
►HTML tags are not supported in subtitles.
►Time information in an external subtitle file should be arranged in ascending order to be played.
►The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the
audio language is changed.
►A damaged video file may not be played correctly, or some functions may not be usable.
►Video files produced with some encoders may not be played correctly.
►If the video and audio structure of recorded file is not interleaved, the file not playback properly.
►Video with resolution higher than maximum resolution supported for each frame, cannot be guaranteed for smooth playback.
►Video files other than the specified types and formats may not work properly.
►The movie file encoded by the GMC (Global Motion Compensation) is not supported.
►Only 250 Korean characters, 500 letters and 500 numbers are supported for each line of the
subtitle.
►Only 10000 sync blocks are supported within the subtitle file.
►We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/AVC.
►DTS Audio codec is not supported.
►A video file more than 30GB in file size is not supported for playback.
►Playing a video via a USB connection that doesn’t support high speed may not work properly.
►USB storage devices below USB 2.0 are supported as well. But they may not work properly in the
movie list.
►The video file and its subtitle file must be located in the same folder.
At this time, a video file name and its subtitle file name must be identical for it to be displayed.
►When you are watching a movie via the Movie List function, you can adjust the picture with the
ENERGY SAVING and AV MODE button on the remote control. User setup for each picture mode
is not supported.
80
Supported Video Formats
File
Audio Codec
mpg, mpeg
MPEG1, MPEG2
MP2, MP3, Dolby Digital, LPCM
dat
MPEG1
MP2
ts, trp, tp
MPEG2, H.264, AVS, VC1
MP2,MP3,DolbyDigital
vob
MPEG1, 2
MP2, MP3, Dolby Digital, LPCM
mp4, mov
MPEG4,DivX 3.11, DivX 4.12, DivX 5.x,
DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02,
Xvid 1.03, Xvid 1.10-beta1/2H.264
MP3
mkv
H.264, MPEG-1,2,4
divx, avi
MPEG2, MPEG4, DivX 3.11, DivX 4,
DivX 5, DivX 6, Xvid 1.00, Xvid 1.01,
Xvid 1.02, Xvid 1.03, Xvid
1.10-beta1/2H.264
MP2,MP3,DolbyDigital,
LPCM, ADPCM
JPEG
LPCM, ADPCM
asf, wmv
VC1
WMA
flv
Sorenson H.263, H264
MP3
Motion JPEG
(avi, mp4, mkv)
Max Resolution
MP2,MP3,
DolbyDigital,LPCM
1920 x 1080 @ 30p
MY MEDIA
Video Decoder
Extension name
(Only Motion JPEG
640x480@30p)
81
MY MEDIA
Screen Components
1
MENU
Select MY MEDIA.
2
ENTER
Select Movie List.
ENTER
1
Moves to upper level folder
2 Current page/Total pages
3 Corresponding buttons on the
remote control
4 Contents under the folder
focused on 1
5 Current page/total pages of
contents
2
1
Page 1/1
Movie List
Drive1
USB 1 XTICK
M1
Page 1/1
M2
M3
M4
MY MEDIA
Moon Child.DivX.A
01:34:33
4
� Move
ꔅ To Photo List
ꔅ Change Numbers
� Play
ꔅ Mark Mode
� Page Change � Mark
ꕯ Exit
3
82
GREEN
Move to Photo List or Music List.
YELLOW
Change Numbers: Changes the number or thumbnails displayed at a time.
BLUE
Allows you to mark certain files.
EXIT
Return to TV viewing.
5
Movie Selection
Page 1/1
Movie List
1
Drive1
USB 1 XTICK
M1
Select the target folder or drive.
Page 1/1
M2
M3
M4
2
ENTER
3
ENTER
Moon Child.DivX.A
01:34:33
� Move
ꔅ Change Numbers
Play the movie file.
� Page Change � Mark
ꔅ Mark Mode
ꕯ Exit
ꔛ
Use the CH (ꕌꕍ) button to navigate
in the movie page.
Mark Mode
1
Page 1/1
Movie List
Mark Mode
Drive1
USB 1 XTICK
M1
M2
M4
Moon Child.DivX.A
01:34:33
� Move
ꔅ Play Marked
RED
ꔅ Mark All
ꔅ Unmark All
� Mark
� Page Change � Mark
ꔅ Exit Mark Mode
ꕯ Exit
Play Marked: Play the first selected file. Once
a movie finishes playing, the next selected
one will be played automatically.
GREEN
Mark All: Mark all files in the folder.
YELLOW
Unmark All: Deselect all marked files.
BLUE
Select the target folder or
drive.
Page 1/1
M3
2
ENTER
3
MARK
4
MY MEDIA
ꔅ To Photo List
� Play
Select the desired
movie title.
FAV
RED
ꔛ
Select the desired
movie title.
Mark your desired movie file.
Play the marked movie file.
It displays the current movie
status progress bar on the bottom of the screen.
When one or more movie files are
marked, the marked movies will be
played in sequence.
Exit the Mark Mode.
83
MY MEDIA
Using the Movie List Function
Choose options.
Set Video Play.
Set Video.
Set Audio.
Close
��
�
�
MY MEDIA
1
�
�
01:02:30 / 02:30:25
�
�
�
� Option
� Hide
ꕯ Exit
Show the Option menu.
Q.MENU
2
ENTER
Select Set Video Play., Set Video., or
Set Audio.
Using the remote control
!
?
! NOTE
►Option values changed in the Movie List
does not affect Photo List and Music
List.
? Option values changed in Photo List and
►
Music List are changed likewise in Photo
List and Music List, but not in the Movie
List.
►When replaying a video file after stopping, you can play from where it stopped
automatically.
►If you select “Yes” when playing the
same file after the video file has been
stopped, it will restart where it stopped
previously.
►If continuous series files exist within the
folder, the next file will automatically be
played. But, this excludes cases when
the Repeat function of Movie List Option
is turned “On” (Refer to page 85) or
when set as Marked Play.
Return to TV viewing.
EXIT
Select the required speed: x2, x4, x8, x16, x32 (backward/forward).
Pauses the media player.
If no buttons are pressed on the remote control for 10 minutes after pausing, the
TV returns to the playback state. Displays a slow motion.
Move to a specific frame forward or backward while playing a video. A cursor indicating the position can be viewed on the screen. It may not work properly for
some movie files.
Return to normal playback.
BACK
or
ENERGY
SAVING
RETURN
Hide the menu on screen. To see the menu again, press ENTER button to display.
Press the ENERGY SAVING button repeatedly to increase the brightness of your
screen (Refer to p. 104).
AV MODE
84
Press the AV MODE button repeatedly to select the desired source (Refer to p. 75).
Set Video Play Menu Options
Set Video Play.
◀
Full
▶
Audio Language
◀
1
▶
Subtitle
◀
On
▶
•Language
◀
Unknow
▶
•Code Page
◀
Default
▶
•Sync
◀
0
▶
•Position
◀
0
▶
•Size
◀
Normal
▶
Repeat
◀
Off
▶
MY MEDIA
Picture Size
� Previous
1
2
Select Picture Size, Audio Language,
Subtitle, or Repeat.
Make appropriate adjustments.
Code Page
Subtitle Language Group
Supported Language
Latin1
English, Spanish, French
Korean
English, Korean
Picture Size: Selects your desired
picture format for videos.
ꔛ Audio
Language: Changes the
Language Group of the audio for
video files.
ꔛ Subtitle Language: The subtitles can
be turned on or off. If there are two
or more subtitles, you can select one
of them.
ꔛ Language: Activated for SMI subtitles
and can select the language within
the subtitle.
ꔛ Code Page: Subtitle font selection.
When set to default, same font as
general menu will be used.
ꔛ Sync: When the video is not synchronized with the captions, it can be
adjusted by 0.5 second.
ꔛ Position: Move the location of the
subtitles.
ꔛ Size: Changes the subtitle font size.
ꔛ Repeat: Turn on/off repeat function
of movie playback. When turned on,
the file within the folder will be played
back repeatedly.
ꔛ
85
MY MEDIA
* Image shown may differ from your TV.
Set Video Menu Options
Set Video.
◀
Picture Mode
▶
•Backlight
70
◀
▶
•Contrast
100
◀
▶
•Brightness
50
◀
▶
•Color
60
◀
▶
MY MEDIA
•Dynamic Contrast
◀
Medium
▶
•Edge Enhancer
◀
High
▶
•Noise Reduction
◀
Medium
▶
◀
Low
▶
TruMotion
ꔅ Picture Reset
1
Standard
('TruMotion' dependent on model)
� Previous
Select Picture Mode or TruMotion.
2
Make appropriate adjustments.
BLUE
Reset picture settings to default.
Set Audio Menu Options
Set Audio.
Sound Mode
◀
Standard
▶
Auto Volume
◀
Off
▶
Clear Voice II
◀
Off
▶
Balance
0 ◀ L
R
▶
� Previous
1
2
86
Select Sound Mode, Auto Volume, Clear
Voice II or Balance.
Make appropriate adjustments.
PHOTO LIST
The On-Screen Display on your model may be slightly different.
Supported photo file: *.JPG
ꔛ Baseline: 64 pixel (width) x 64 pixel (height) to 15360 pixel (width) x 8640 pixel (height)
ꔛ Progressive: 64 pixel (width) x 64 pixel (height) to 1920 pixel (width) x 1440 pixel (height)
ꔛ You can play JPEG files only.
ꔛ Non-supported files are displayed in the form of predefined icon.
Screen Components
MENU
2
Select MY MEDIA.
Moves to upper level folder
2 Current page/total pages
3 Corresponding buttons on the
remote control
4 Contents under the folder
focused on 1
5 Current page/total pages of
contents
ENTER
Select Photo List.
ENTER
1
1
2
Page 1/1
Photo List
USB 1 XTICK
Drive1
P1
P2
MY MEDIA
1
P3
P4
Page 1/1
P5
P6
P7
P8
5
P9
4
� Move
ꔅ To Music List
ꔅ Change Numbers
� View
ꔅ Mark Mode
� Page Change
� Mark
ꕯ Exit
3
GREEN
Move to Music List or Movie List.
YELLOW
Change Numbers: Changes the number or thumbnails displayed at a time.
BLUE
Allows you to mark certain files.
EXIT
Return to TV viewing.
87
MY MEDIA
Photo Selection
1
Page 1/1
Photo List
USB 1 XTICK
Drive1
Page 1/1
� Move
MY MEDIA
ꔅ To Music List
ꔅ Change Numbers
� View
� Page Change
ꔅ Mark Mode
� Mark
Select the target folder or drive.
2
ENTER
3
ENTER
ꔛ
ꕯ Exit
Select the desired photos.
Photo file is displayed.
Use the CH (ꕌꕍ) button to navigate
in the photo page.
Mark Mode
Mark Mode
Drive1
USB 1 XTICK
� Move
ꔅ View Marked
RED
ꔅ Mark All
ꔅ Unmark All
Page 1/1
� Mark
� Page Change
ꔅ Exit Mark Mode
� Mark
View Marked: Display the selected photo.
Mark All: Mark all photos on the screen.
YELLOW
Unmark All: Deselect all marked photos.
Exit the Mark Mode.
Select the target folder or drive.
2
ENTER
3
MARK
4
FAV
RED
Select the desired
photo files.
Mark your desired photo files.
View the marked photo files.
ꕯ Exit
GREEN
BLUE
88
1
Page 1/1
Photo List
ꔛ
When one or more photos are
marked, you can view individual photos or a slide show of the marked
photos. If no photos are marked, you
can view all photos individually or all
photos in the folder in a slide show.
Full Screen Menu
More operations are available in full screen mode.
Page 1/1
Photo List
USB 1 XTICK
Drive1
Page 1/1
� Move
ꔅ Change Numbers
� View
� Page Change � Mark
ꔅ Mark Mode
MY MEDIA
ꔅ To Music List
ꕯ Exit
01_a.jpg
2008/12/10
1920 x 1080
479 KB
◀
▶
◀
Slideshow �
1
BGM �
�
2/13
�
�
The aspect ratio of a photo may change the size
of the photo displayed on the screen in full size.
▶
� Option
� Hide
Select the target folder or drive.
2
ENTER
3
ENTER
ꕯ Exit
ꔛ
Use the CH (ꕌꕍ) button to navigate
in the photo page.
Select the desired photos.
The selected photo is displayed in full
size.
89
4
01_a.jpg
2008/12/10
1920 x 1080
479 KB
ENTER
Select the Slideshow,
◀
▶
BGM, � (Rotate),
� (Zoom In), � (Energy Saving),
Option, or Hide.
ꔛ
◀
MY MEDIA
▶
MY MEDIA
Slideshow �
BGM �
�
�
2/13
�
▶
� Option
� Hide
Use < > button to select the previous or next photo.
ꕯ Exit
►Slideshow: Selected photos are displayed during the slide show. If no photo is selected, all photos
in the current folder are displayed during slide show.
ꔛ Set the time interval of the slide show in Option-Set Photo View. menu (Refer to p. 91).
ꔛ You can adjust Option by using the Q.MENU button on the remote control.
►BGM (Background Music): Listen to music while viewing photos in full size.
ꔛ Set
the BGM device and album in Option-Set Photo View. menu (Refer to p. 91).
ꔛ You
can adjust Option by using the Q.MENU button on the remote control.
►� (Rotate): Rotate photos.
ꔛ Rotates the photo 90 °, 180 °, 270 °, 360 ° clockwise.
ꔛ Photos cannot be rotated if its width is greater than the available supported resolution height.
►� (Zoom In): View the photo by zoom in 2, 4 times by using Blue button.
►� (Energy Saving): Increase the brightness of your screen by using ENERGY SAVING button.
►Option: Set values for Slide Speed and Music Album (Refer to p. 91).
ꔛ You cannot change Music Album while BGM is playing.
ꔛ You can only select the MP3 folder saved on the device that currently displays the photo.
► Hide: Hide the menu on the full-sized screen.
ꔛ To
see the menu again on the full-sized screen, press ENTER button to display.
► Exit: Move to the previous menu screen.
90
Using the Photo List Function
01_a.jpg
2008/12/10
1920 x 1080
479 KB
Choose options.
Set Photo View.
◀
▶
Set Video.
Set Audio.
Close
Slideshow �
1
2
Q.MENU
BGM �
�
2/13
�
�
▶
� Option
� Hide
Show the Option menu.
ENTER
MY MEDIA
◀
Select Set Photo View., Set Video.,
or Set Audio.
ꕯ Exit
!
! NOTE
?
►Option values changed in Photo List do
not affect Movie List and Music List.
? Option values changed in Photo List or
►
Music List are changed likewise in Photo
List and Music List, but not Movie List.
Set Photo View Menu Options
Set Photo View.
Slide Speed
◀
Music Album
Fast
▶
Drive1
•Repeat
◀
On
▶
•Random
◀
Off
▶
� Previous
1
2
Select Slide Speed or Music Album.
Make appropriate adjustments.
91
MY MEDIA
* Image shown may differ from your TV.
Set Video Menu Options
Set Video.
◀
Picture Mode
Standard
▶
•Backlight
70
◀
▶
•Contrast
100
◀
▶
•Brightness
50
◀
▶
•Color
60
◀
▶
•Dynamic Contrast
◀
Medium
▶
•Edge Enhancer
◀
High
▶
•Noise Reduction
◀
Medium
▶
◀
Low
▶
MY MEDIA
TruMotion
ꔅ Picture Reset
1
(depending on models)
� Previous
Select Picture Mode or TruMotion.
2
Make appropriate adjustments.
BLUE
Initialize the adjusted picture value.
Set Audio Menu Options
Set Audio.
Sound Mode
◀
Standard
▶
Auto Volume
◀
Off
▶
Clear Voice II
◀
Off
▶
Balance
0 ◀ L
R
▶
� Previous
1
2
92
Select Sound Mode, Auto Volume, Clear
Voice II or Balance.
Make appropriate adjustments.
MUSIC LIST
This TV cannot play back copy-protected files.
The On-Screen Display on your model may be slightly different.
MUSIC (*.MP3) supporting file
Bit rate 32 Kbps - 320 Kbps
• Sampling rate MPEG1 Layer3: 32 kHz, 44.1 kHz, 48 kHz
• Sampling rate MPEG2 Layer3: 16 kHz, 22.05 kHz, 24 kHz
• Sampling rate MPEG2.5 Layer3: 8 kHz, 11.025 kHz, 12 kHz
1
MENU
Select MY MEDIA.
2
ENTER
Select Music List.
ENTER
1
Preview: If any album jacket for
the file (Album Art Image)
exists, this picture is displayed.
2 Moves to upper level folder
3 Current page/Total pages
4 Corresponding buttons on the
remote control
5 Contents under the folder
focused on 1
6 Current page/total pages of
contents
2
1
Page 1/1
Music List
Drive1
USB 1 XTICK
001. - B01.mp3
00:00
MY MEDIA
Screen Components
Page 1/1
002. - B02.mp3
00:00
003. - B03.mp3
00:00
004. - B04.mp3
00:00
4
005. - B05.mp3
00:00
� Move
ꔅ To Movie List
5
ꔅ Change Numbers
� Play
ꔅ Mark Mode
� Page Change
� Mark
ꕯ Exit
3
GREEN
Move to Movie List or Photo List.
YELLOW
Change Numbers: Changes the number or thumbnails displayed at a time.
BLUE
Allows you to mark certain files.
EXIT
Return to TV viewing.
ENERGY
SAVING
Press the ENERGY SAVING button repeatedly to increase the brightness of your
screen (Refer to p. 104).
(It's available "ENERGY SAVING - Off, Screen Off" only.)
93
MY MEDIA
Music Selection
Page 1/1
Music List
Drive1
USB 1 XTICK
001. - B01.mp3
00:00
Page 1/1
002. - B02.mp3
00:00
003. - B03.mp3
00:00
004. - B04.mp3
00:00
005. - B05.mp3
00:00
� Move
ꔅ To Movie List
ꔅ Change Numbers
� Play
� Page Change
ꔅ Mark Mode
1
Select the target folder or drive.
2
ENTER
3
ENTER
Select the desired
music file.
Music files are played.
� Mark
ꕯ Exit
ꔛ
MY MEDIA
Use the CH (ꕌꕍ) button to navigate
in the music page.
Mark Mode
Mark Mode
Drive1
USB 1 XTICK
001. - B01.mp3
00:00
1
Page 1/1
Music List
002. - B02.mp3
00:00
Page 1/1
003. - B03.mp3
00:00
004. - B04.mp3
00:00
005. - B05.mp3
00:00
� Move
ꔅ Play Marked
RED
ꔅ Unmark All
� Mark
� Page Change
ꔅ Exit Mark Mode
� Mark
ꕯ Exit
Play Marked: Play the selected songs. Once a
song finishes playing, the next selected one
will be played automatically.
GREEN
Mark All: Mark all songs in the folder.
YELLOW
Unmark All: Deselect all marked song.
BLUE
94
ꔅ Mark All
Exit the Mark Mode.
Select the target folder or
drive.
2
ENTER
3
MARK
4
FAV
RED
ꔛ
Select the desired
music file.
Mark your desired music file.
Play the marked music file.
When one or more music files are
marked, the marked music files will
be played in sequence.
Using the Music List Function
Page 1/1
Music List
3 file(s) Marked
Drive1
Choose options.
Page 1/1
Set Audio Play.
�
001. - B01.mp3
00:00
002. - B02.mp3
00:00
�
005. - Mad (Feat).mp3
�
Q.MENU
2
�
�
�
003. - B03.mp3
00:00
�
004. - B04 .mp3
00:00
�
��
� Play with Photo
005. - B05 .mp3
00:00
02:30 / 03:25
�
� Option
� Hide
Show the Option menu.
ENTER
Close
Select Set Audio Play. or Set Audio..
ꕯ Exit
!
?
! NOTE
MY MEDIA
1
�
Set Audio.
�
►Option values changed in Movie List
does not affect Photo List and Music
? List.
►Option value changed in Photo List and
Music List are changed likewise in Photo
List and Music List excluding Movie List.
►You can listen to the music only within
the device currently played.
Using the remote control
Stop playback.
Return to normal playback.
Paused playback.
Select the previous or next song.
GREEN
ENERGY
SAVING
Play with Photo: Start playing the selected songs and then move to the Photo List.
Press the ENERGY SAVING button repeatedly to increase the brightness of your screen
(Refer to p. 104). (It's available "ENERGY SAVING - Off, Screen Off" only.)
A cursor indicating the position can be played on the screen.
EXIT
Move to the previous menu screen.
95
MY MEDIA
Set Audio Play Menu Options
Set Audio Play.
Repeat
◀
On
▶
Random
◀
Off
▶
� Previous
1
Select Repeat or Random.
MY MEDIA
2
Make appropriate adjustments.
Set Audio Menu Options
Set Audio.
Sound Mode
◀
Standard
▶
Auto Volume
◀
Off
▶
Clear Voice II
◀
Off
▶
Balance
0 ◀ L
R
▶
� Previous
1
Select Sound Mode, Auto Volume, Clear
Voice II or Balance.
2
Make appropriate adjustments.
ꔛ
If you don't press any buttons for a while, the play information box
will float across the screen. This prevents screen pixel damage due
to a fixed image remaining on the screen for a extended period of
time.
002. B02.mp3
� 00:31 / 04:04
!
96
?
! NOTE
►Music files with copy-protection will not play.
►Press ENTER or � button to stop the screen saver.
?
EXTRA CONTENTS
-F
or 32/37/42/47LD452C
You can play application files on USB device.
Application files your device can be played by this unit.
The On Screen Display may be different from your TV. Images are an example to assist with the TV
operation.
FLASH (*.SWF) / GEM supporting file
An SWF file complied with Flash Lite 3.0 or earlier (the 3.0 version is recommended)
MY MEDIA
•T
he Pro: Centric application is required, which starts automatically in the flash memory when the
TV is turned on.
•T
he folder called /hcapfs/as/abs_service/ must exist in USB drive root directory.
•T
he file called xait.xml must exist in the /hcapfs/as/abs_service/ folder.
• If the above conditions are not met, the following error message is displayed when selecting the
Extra Contents option: Failed to execute file in the USB. Please check the files in the USB.
•W
hen the flash file does not run even if the above all conditions are met, refer to the Download Extra
Contents of Installation Guide.
• GEM is composed of JAVA application.
Playing the application files
1
Select MY MEDIA.
MENU
2
Select Extra Contents.
ENTER
3
ENTER
Application files are played.
To stop playing the Application file
Remove the USB from the USB IN jack of the TV set.
!
?
! NOTE
►When playing the Application files(FLASH or GEM files), the buttons are controlled according
to the settings of the Extra Contents option.
?
97
MY MEDIA
EZSIGN TV
- For 32/42/47LD452B
TheEzSignTVfunctionallowsyoutoplayandmanagehigh-qualityadcontentthatyoucreatequickly
andeasilyusingtheEzSignTVEditor.
ꔛ Formoreinformationofusing,refertotheEzSign TV Editor S/W & Manual.
√ TV memory
USB
EzSign TV content exists. How do you want
to manage this content?
Play
MY MEDIA
EzSign TV
Delete
Close
Photo List
or
Music List
√ USB
TV memory
MY MEDIA
How do you want to play the EzSign TV
Content?
Copy to TV memory & Play
Play
Close
1
SelectMY MEDIA.
MENU
2
3
ENTER
4
ENTER
SelectEzSign TV.
ENTER
ꔛ
TV memory
Play
SelectTV memory orUSB.
Thehighlightedtabwiththe"√"symbol indicates the location of the file
currentlybeingplayed
PlaysEzSignTVcontentinthememory.
Delete
DeletesEzSignTVcontentfromthememory.(YourTVrestartsafterthecontentisdeleted.)
Close
ClosestheEzSignTVmenuwindow.
USB
CopiesafilefromtheUSBmemorytotheEzSignTVmemoryandplaysit.
Copy to TV memory &
(Oncethefilehasbeencopied,itcanbeplayedevenwhenitisremovedfrom
Play
theUSBmemory.)
Play
Close
98
PlaysafiledirectlyfromtheUSBmemorywithoutcopyingittotheEzSignTVmemory.
ClosestheEzSignTVmenuwindow.
!
! NOTE
?
►WhileloadingEzSignTVcontent,yourTVmayfunctionslowerthannormal.
►It is recommended that you copy files to the TV memory before playing them, as playing
? directlyfromtheUSBmemoryforanextendedperiodoftimemaycausethedevicetooverheat.
►InEzSignTV,someremotecontrolkeysmaynotwork.
DIVX REGISTRATION CODE
Except 32/42/47LD420, 32/37/42/47LD450, 37/42/47LD450C, 32/42/47/55LD520, 55LD520C,
42/47/55LE530C, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C
Using the registration number, movies can be rented or purchased at www.divx.com/vod.
Only DivX files matched with the registration code of the purchased TV are playable.
DivX Reg.Code
MY MEDIA
i
Deactivation
Movie List
1
Music List
Select MY MEDIA.
MENU
ENTER
BLUE
Select DivX Option.
� Previous
Close
3
4
Select DivX Reg. Code.
ENTER
MY MEDIA
2
Photo List
You must register your device to
play DivX protected videos.
Registration code : xxxxxxxxxx
Register at http://vod.divx.com
Display DivX Reg. Code.
!
! NOTE
?
►When loading, some buttons may not work.
►If you use the DivX registration code of another device, the rented or purchased DivX file cannot
? be played. Therefore always use the DivX registration code assigned to this product.
►The video or audio of a file converted based on a standard other than the DivX codec standard
may be corrupted or unable to be played.
DEACTIVATION
Except 32/42/47LD420, 32/37/42/47LD450, 37/42/47LD450C, 32/42/47/55LD520, 55LD520C,
42/47/55LE530C, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C
The purpose of deactivation is to allow deactivation of devices for users who have activated all the
available devices through the web server and are blocked from activating more devices. DivX VOD
allows the consumer to activate up to 6 devices under one account.
Delete the existing authentication information to receive a new DivX user authentication for TV. Once
this function is executed, a DivX user authentication is required again to see DivX DRM files.
i
DivX Reg.Code
MY MEDIA
Deactivation
Movie List
1
2
3
MENU
ENTER
BLUE
Photo List
Music List
� Previous
Select MY MEDIA.
4
Select DivX Option.
5
Select Deactivation.
Deregistration code:
********
Deregister at http://vod.divx.com
Continue with registration?
Yes
ENTER
ENTER
No
Select Yes.
Display Deactivation.
99
PICTURE
PICTURE CONTROL
CONTROL
PICTURE SIZE (ASPECT RATIO) CONTROL
This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV.
You can select a different aspect ratio depending on input source (analog broadcasting, digital broadcasting, aux).
PICTURE
� Move
• Aspect Ratio
: 16:9
� Enter
ꔉ
ꔡ
• Picture Wizard
• ꕊ Energy Saving : Off
PICTURE
ꔂ Move
• Aspect Ratio
ꔉ Enter
: 16:9
• Picture Wizard
• ꕊ Energy Saving : Off
ꔑ 16:9
• Picture Mode
: Standard
• Picture Mode
: Standard
• Backlight
70
• Backlight
• Contrast
100
• Contrast
• Brightness
50
• Brightness
50 □ 4:3
• Sharpness
70
• Sharpness
70 □ Zoom
70 □ Just Scan
ꔉ
ꔡ
100 □ Set By Program
□ Cinema Zoom 1
PICTURE CONTROL
1
2
3
MENU
Select PICTURE.
ENTER
Select Aspect Ratio.
ENTER
Select the desired picture format.
4
RETURN
EXIT
or
BACK
You can also adjust Aspect Ratio in
the Q.MENU.
ꔛ Press the RATIO button repeatedly to
select the desired picture format.
ꔛ
Return to the previous menu.
Return to TV viewing.
When adjusting Zoom or Cinema Zoom in Q.MENU
1
2
3
4
100
Q.MENU
Select Aspect Ratio.
ENTER
Select Zoom or Cinema
Zoom.
ENTER
Adjust proportion of Zoom or
Cinema Zoom. The Cinema
Zoom adjustment range is
1-16.
ENTER
Move the image on the screen.
Zoom
� Move � Zoom
Cinema Zoom
� Enter
� Move � Zoom
� Enter
16:9
4:3
Adjust the picture horizontally, in a linear
proportion to fill the entire screen.
Choose 4:3 when you want to view a picture
with an original 4:3 aspect ratio.
Just Scan
Zoom
Cinema Zoom
Normally the edges of video signals are
cropped 1-2%. Just Scan turns off this
cropping and shows the complete video.
Notes: If there is noise on the edges of the
original signal, it will be visible when Just Scan
is activated.
Just Scan operates only in DTV/Cable DTV/
C o m p o n e n t / H D M I - DT V/ D V I - DT V
(720p/1080i/1080p) input source.
Just Scan
Set By Program
Selects the proper picture proportion to
match the source’s image.
(4:3
Choose Zoom when you want to view the
picture without any alteration. However, the
top and bottom portions of the picture will
be cropped.
PICTURE CONTROL
Choose Cinema Zoom when you want to
enlarge the picture in correct proportion.
This enlarges an image with cinemascope
aspect ratio (2.35:1) without distortion.
Note: When enlarging or reducing the picture, the image may become distorted.
4:3)
Set By Program
(16:9
16:9)
Set By Program
101
PICTURE CONTROL
PICTURE WIZARD
This feature lets you adjust the picture quality of the original image. Use this to calibrate the screen
quality by adjusting the Black and White Level etc. You can calibrate the screen quality by easily following each step. When you adjust the image to Low, Recommended or High, you can see the example of
the changes you made.
PICTURE
ꔂ Move
• Aspect Ratio
ꔉ Enter
: 16:9
ꔉ
ꔀ
• Picture Wizard
Black Level
Set the screen above identical to the Recommended sample
below.
• ꕊ Energy Saving : Off
1
PICTURE CONTROL
2
• Picture Mode
: Standard
• Backlight
70
• Contrast
100
• Brightness
50
• Sharpness
70
Low
Recommended
• Brightness
High
50 ◀
▶
ꕉ Previous
Select PICTURE.
MENU
ENTER
ENTER
5
ꔉ Next
ENTER
Select Picture
Wizard.
White Level
Picture Wizard
With Picture Wizard, you can adjust the picture quality of the
original image.
Set the screen above identical to the Recommended sample
below.
ꕖ
Low
Recommended
• Contrast
ꕉ Previous
3
ENTER
Adjust Black Level.
ꔉ Next
Adjust Picture Wizard.
High
90 ◀
▶
ꕉ Previous
6
ꔉ Next
ENTER
Adjust White Level.
Picture Wizard
Tint
Set the screen above identical to the Recommended sample
below.
Standard
• Standard/Preferred
Preferred
Low
◀ Standard ▶
Recommended
• Tint
ꕉ Previous
4
ꔛ
102
0
◀
High
R
G
▶
ꔉ Next
ꕉ Previous
ENTER
Adjust Standard/
Preferred.
If you select Preferred, OSD (On Screen
Display) differ from that shown in this manual.
7
ꔉ Next
ENTER
Adjust Tint.
Backlight
Color
Set the screen above identical to the Recommended sample
below.
Low
Recommended
• Color
50 ◀
ꕉ Previous
8
Dark
High
Recommended
• Backlight
▶
ꔉ Next
ENTER
Set the Backlight to your Brightness preference.
30 ◀
▶
ꕉ Previous
ꔉ Next
11
Adjust Color.
Bright
ENTER
Adjust Backlight.
i.e)
Complete
Horizontal Sharpness
Set the screen above identical to the Recommended sample
below.
� Move
ꘁ Mark
Select (an) input(s) to apply the settings.
ꔑ DTV
PICTURE CONTROL
□ TV
□ AV1
□ AV2
Low
Recommended
• H Sharpness
50 ◀
ꕉ Previous
High
□ Component1
□ Component2
▶
□ RGB-PC
ꔑ HDMI1
ꔉ Next
ꔑ HDMI2
ꔑ HDMI3
9
ENTER
Adjust Horizontal
Sharpness.
ꔑ HDMI4
Warning: The picture quality may vary according to the different types of
signal and inputs.
ꕉ Previous
Vertical Sharpness
Set the screen above identical to the Recommended sample
below.
Low
Recommended
• V Sharpness
50 ◀
High
12
ꔉ Confirm
MARK
FAV
13
Select input source to
apply the settings.
i
ENTER
Save.
The current adjustment value is
saved to Expert1.
▶
Close
ꕉ Previous
ꔉ Next
10
ENTER
Adjust Vertical
Sharpness.
14
ENTER
Finish the Picture Wizard.
If you stop the Picture Wizard before the
final step, the changes will not be saved to
the TV.
ꔛ Once the Picture Wizard sets the picture
quality, Energy Saving is changed to Off
automatically.
ꔛ To reset changes made by Picture Wizard,
operate Picture Reset when Picture Mode
is on Expert1.
ꔛ
103
PICTURE CONTROL
ꕊ ENERGY SAVING
It reduces the TV’s power consumption by lowering the backlight level.
You can increase the brightness of your screen by adjusting the Energy Saving level or by adjusting the
Picture Mode.
i.e) PICTURE
• Aspect Ratio
ꔂ Move
ꔉ Enter
: 16:9
PICTURE CONTROL
3
: Standard
ꔉ
ꔀ
• Backlight
• Contrast
• Brightness
• Sharpness
70
• Backlight
100
• Contrast
50
• Brightness
70
• Sharpness
Select ꕊ Energy Saving.
ENTER
Select Off, Minimum, Medium,
Maximum, or Screen Off.
EXIT
BACK
Return to the previous menu.
Return to TV viewing.
• ꕊ Energy Saving : Off
: Standard
ENTER
or
: 16:9
• Picture Mode
Select PICTURE.
RETURN
104
• Picture Mode
MENU
4
ꔉ Enter
• Picture Wizard
• ꕊ Energy Saving : Off
2
ꔂ Move
• Aspect Ratio
• Picture Wizard
1
PICTURE
□ Auto
ꔑ Off
70
□ Minimum
90
□ Medium
50
□ Maximum
70
□ Screen Off
ꔉ
ꔀ
When selecting Screen off, the
screen will turn off after 3 seconds.
ꔛ If
you adjust “Energy SavingMaximum”, Backlight feature will not
work.
ꔛ Press the ENERGY SAVING button
repeatedly to select the appropriate
Energy Saving setup.
ꔛ
PRESET PICTURE SETTINGS (PICTURE MODE)
There are factory presets for picture settings available in the user menus. You can use a preset, change
each setting manually.
PICTURE
ꔂ Move
• Aspect Ratio
ꔉ Enter
: 16:9
PICTURE
• Aspect Ratio
• Picture Wizard
ꔂ Move
ꔉ Enter
: 16:9
• Picture Wizard
• ꕊ Energy Saving : Off
• ꕊ Energy Saving : Off
• Picture Mode
: Standard
• Backlight
70
□ Intelligent Sensor
: Standardꔉ
• Backlight
70 □ Vivid
• Contrast
100
• Contrast
• Brightness
50
• Brightness
50
• Sharpness
70
• Sharpness
70
ꔉ
ꔀ
• Picture Mode
100
ꔑ Standard
□ Cinema
ꔉ
ꔀ
Depending on
models
□ Sport
□ Game
□ � Expert1
□ � Expert2
2
3
MENU
Select PICTURE.
ENTER
Select Picture Mode.
ENTER
Select Vivid, Standard, Cinema, Sport,
or Game.
4
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
Vivid, Standard, Cinema, Sport, and
Game Settings are preset for the optimum picture quality at the factory.
ꔛ Vivid: This is the mode to maximize
the effect of the video in the retail
store. Strengthen the contrast, brightness, color and sharpness for vivid
picture.
ꔛ Standard: This is the mode to realize
optimum viewing condition for the
general user.
ꔛ Cinema: This mode optimizes video
for watching movies.
ꔛ Sport: This is the video mode to
emphasize dynamic video and primary color (e.g, white, uniform, grass,
sky blue etc.) by realizing the optimal
screen for sports.
ꔛ Game: This is the mode to realize fast
response speed in a fast gaming
screen.
ꔛ Expert: This is the mode to adjust
the video in detail for video quality
expert and general user.
ꔛ You can also adjust Picture Mode in
the Q.MENU.
ꔛ When
selecting Intelligent Sensor,
Energy Saving is changed to Auto automatically.
ꔛ When selecting Intelligent Sensor, it
changes Backlight, contrast, brightness, sharpness, color and tint automatically.
ꔛ Intelligent Sensor: The most suitable
picture is automatically adjusted
according to the surrounding conditions.
ꔛ
PICTURE CONTROL
1
105
PICTURE CONTROL
MANUAL PICTURE ADJUSTMENT - USER MODE
Adjust the picture appearance to suit your preference and viewing situations.
PICTURE
• Aspect Ratio
ꔂ Move
ꔉ Enter
: 16:9
• Picture Wizard
ꔠ
• ꕊ Energy Saving : Off
PICTURE CONTROL
1
2
3
4
5
: Standard
• Backlight
70
• Contrast
100
• Brightness
50
• Sharpness
70
ENTER
Select Picture Mode.
ENTER
Select Vivid, Standard, Cinema,
Sport, or Game.
ENTER
Select Backlight, Contrast, Brightness,
Sharpness, Color, Tint, Color Temp., or
Advanced Control.
ENTER
Make appropriate adjustments.
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
ꔡ
ꔉ
ꔀ
Select PICTURE.
RETURN
106
• Picture Mode
MENU
6
70 ◀
• Backlight
▶
ꔉ Enter
Backlight: This function adjusts the
brightness of the backlight behind
the LCD screen. Adjusting the backlight is recommended when setting
the brightness of the TV. When
decreasing the backlight, the brightness of the black becomes darker
without any loss in video signal and
the power consumption is reduced.
ꔛ Contrast: Increase or decrease the
gradient of the video signal. You may
use Contrast when the bright part of
the picture is saturated.
ꔛ Brightness: Adjusts the base level of
the signal in the picture. You may use
Brightness when the dark part of the
picture is saturated.
ꔛ Sharpness: Adjusts the level of crispness in the edges between the light
and dark areas of the picture. The
lower the level, the softer the image.
ꔛ Color: Adjusts intensity of all colors.
ꔛ Tint: Adjusts the balance between
red and green levels.
ꔛ Color Temp.: Set to warm to enhance
hotter colors such as red, or set to
cool to enhance cooler colors such
as blue.
ꔛ
PICTURE IMPROVEMENT TECHNOLOGY
(ADVANCED CONTROL)
Advanced Control allows you to adjust some of the advanced features of your LG display.
To reset to the factory default after making adjustments to each input source, execute the Picture
Reset function for each Picture Mode.
PICTURE
ꔂ Move
ꔉ Enter
PICTURE
ꔂ Move
ꔉ Enter
• Sharpness
70
• Sharpness
• Color
60
• Color
• Tint
0
R
G
• Color Temp.
0
W
C
70
Dynamic Contrast
60
Dynamic Color
G
• Tint
0 R
• Color Temp. Clear
0 W White C
• Advanced Control
ꔉ
ꔀ
• Picture Reset
• Advanced Control
Skin Color
• TruMotion
: Low
• TruMotion
• Screen (RGB-PC)
• Screen (RGB-PC)
• Picture Reset
: Low
◀
Off
0
Noise Reduction
Off
Digital Noise Reduction
Low
ꔍ
Close
2
3
ENTER
Select Advanced Control.
ENTER
Select your desired menu option.
4
PICTURE CONTROL
Low
Eye Care
Select PICTURE.
Off
Medium
Black Level
MENU
▶
Off
Gamma
1
Low
Make appropriate adjustments.
5
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
107
PICTURE CONTROL
EXPERT PICTURE CONTROL
� Expert1 and � Expert2 provide even more advanced picture settings for users. Typical used by
professionals for calibrating the TV.
PICTURE
• Aspect Ratio
ꔂ Move
PICTURE
ꔉ Enter
: 16:9
ꔉ Enter
• H Sharpness 50
• Picture Wizard
• ꕊ Energy Saving : Off
• V Sharpness 50
Dynamic Contrast
• Color
50
Noise Reduction
• Tint
0 R
Digital Noise Reduction
• Expert Control
Off
• Picture Reset
Black Level
Low
Real Cinema
On
Color Gamut
Wide
□ Vivid
: Expert1ꔉ
• Backlight
70 □ Standard
• Contrast
• Brightness
• H Sharpness 70 □ Game
ꔑ ꕋ Expert1
• Picture Mode
90 □ Cinema
50 □ Sport
• TruMotion
ꔉ
ꔀ
□ � Expert2
• Screen (RGB-PC)
: Low
◀
G
PICTURE CONTROL
High
Auto
Off
Close
3
4
5
MENU
Select PICTURE.
ENTER
Select Picture Mode.
ENTER
Select � Expert1 or � Expert2.
ENTER
Select Expert Control.
ENTER
Select your desired menu option.
6
Make appropriate adjustments.
7
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
Off
xvYcc
ꔍ
1
Off
Edge Enhancer
Expert Pattern
2
108
ꔂ Move
▶
*This feature is not available for all models.
ꔛ
Adjusts the contrast to keep it at the best level according to the brightness
of the screen. The picture is improved by making bright parts brighter and
dark parts darker.
ꔛ
Adjusts screen colors so that they look livelier, richer and clearer. This feature enhances hue, saturation and luminance so that red, blue and green
white look more vivid.
Skin Color
ꔛ
It detects the skin area of video and adjusts it to express a natural skin color.
Noise Reduction
ꔛ
Reduces screen noise without compromising video quality.
Digital Noise
Reduction
ꔛ
Removes noise caused by compressing video.
Dynamic Contrast
Dynamic Color
Gamma
You can adjust brightness of dark areas and middle gray level areas of the
picture.
Low : Make brighter and middle gray level areas of the picture brighter.
Medium : Express original picture levels.
High: Make dark and middle gray level areas of the picture darker.
Black Level
Low: The reflection of the screen gets darker.
High: The reflection of the screen gets brighter.
ꔛ Set black level of the screen to proper level.
ꔛ This function is available in the following modes: AV (NTSC-M), HDMI or
Component.
Clear White
ꔛ
ꔛ
Adjust the brightness of the screen to prevent the screen from being too
bright. Dims extremely bright pictures.
ꔛ This feature is enabled in “Picture Mode-Standard, Sports, Game”.
ꔛ
Eye Care
PICTURE CONTROL
Make the white area of screen brighter and more white.
Makes video clips recorded in film look more natural by eliminating judder
effect.
ꔛ DVD and Blu-ray movies are filmed at 24 frames per second (fps). With
LG Real Cinema, every frame is consistently processed 5 times in 1/24 of
a second producing 120 fps with TruMotion or 2 times in 1/24 of a second
producing 48 fps without TruMotion, thus totally eliminating the judder
effect.
ꔛ This function can also work when TruMotion is off.
ꔛ
Real Cinema
Advanced Control
ꔛ Maximize the utilization of colors to increase color quality.
Standard: Displays standard set of colors.
Wide: Increase number of colors used.
Color Gamut
LED LCD TV/LCD TV: Expert Control
ꔛ Displays color domain of the signal.
Standard: Displays standard set of colors.
Wide: Increase number of colors used.
EBU: Mode to display EBU standard color area.
SMPTE: Mode to display SMPTE standard color area.
BT709: Mode to display BT709 standard color area.
109
PICTURE CONTROL
Edge Enhancer
ꔛ
ꔛ
Show clearer and distinctive yet natural edges in of the video.
This function is enabled in "Picture Mode - Expert".
This is produces richer colors.
This feature represents rich color as much as conventional video signal.
ꔛ This function is enabled in "Picture Mode - Cinema, Expert" when a xvYCC
signal is inputted through HDMI.
ꔛ
xvYCC
Color Filter
Expert Pattern
ꔛ
ꔛ
This function filters specific colors in the video.
You can use the RGB filter to set color saturation and hue accurately.
ꔛ
This is a pattern used for expert adjustment.
This function is enabled in "Picture Mode - Expert" when you watch DTV.
ꔛ
Adjusts the overall color of the screen by changing the white baseline.
a. Gamma : Select 1.9, 2.2, 2.4
b. Method : 2 Points
- Pattern: Inner, Outer
- Red/Green/Blue Contrast, Red/Green/Blue Brightness:
The adjustment range is -50 - +50.
c. Method : 10 Point IRE
- Pattern: Inner, Outer
- IRE (Institute of Radio Engineers) is the unit to display the size of the video
signal and can be set among 10, 20, 30 - 100. You can adjust Red, Green
or Blue according to each setting.
- Luminance: This function displays calculated luminance value for 2.2
gamma. You can input luminance value you want at 100 IRE, then the
target luminance value for 2.2 gamma is displayed at every 10 steps from
10 IRE to 90 IRE.
- Red/Green/Blue: The adjustment range is -50 - +50.
d. Apply to all inputs
ꔛ
PICTURE CONTROL
Color Temperature
A tool used by the experts to make adjustments by using the test patterns,
this does not affect other colors but can be used to selectively adjust the
6 color areas (Red/Green/Blue/Cyan/Mgt/Yellow).
Color difference may not be distinctive even when you make the adjustments for the general video.
Adjusts Red/Green/Blue/Yellow/Cyan/Magenta.
- Red/Green/Blue/Yellow/Cyan/Magenta Color: The adjustment range is
-30 - +30.
- Red/Green/Blue/Yellow/Cyan/Magenta Tint: The adjustment range is -30
- +30.
- This feature is disabled in RGB-PC and HDMI-PC mode.
ꔛ
Color Management
System
110
PICTURE RESET
Settings of the selected picture modes return
to the default factory settings.
PICTURE
ꔂ Move
• Sharpness
PICTURE
ꔉ Enter
70
• Color
60
? All picture settings will be reset.
G
• Tint
0 R
Continue?
• Color Temp.
0
W
• Advanced Control
• Picture Reset
• TruMotion
: Low
Yes
C
No
• Screen (RGB-PC)
1
3
• Sharpness
70
• Color
60
• Tint
0
R
G
• Color Temp.
0
W
C
i
• Advanced
Resetting
videoControl
configuration...
• Picture Reset
• TruMotion
: Low
• Screen (RGB-PC)
4
MENU
Select PICTURE.
ENTER
Select Picture Reset.
ENTER
Select Yes.
Initialize the adjusted value.
ENTER
PICTURE CONTROL
2
ꔉ Enter
ꔉ
ꔀ
ꔂ Move
Return to TV viewing.
EXIT
POWER INDICATOR
Adjust the power/standby indicator light on the front of the TV.
OPTION
ꔂ Move
OPTION
ꔉ Enter
• Language
• Caption
• Caption
ꔉ
ꔀ
3
4
: Off
• Power Indicator
• Initial Setting
2
ꔉ Enter
• Language
: Off
• Power Indicator
1
ꔂ Move
Standby Light
• Initial Setting
Power Light
• Set ID
:1
• Set ID
:1
• Mode Setting
: Home Use
• Mode Setting
: Home Use
MENU
Select OPTION.
ENTER
Select Power Indicator.
ENTER
Select Standby Light or Power
Light.
Select your desired options.
5
RETURN
EXIT
or
BACK
◀
On
▶
On
Close
Return to the previous menu.
Return to TV viewing.
Standby Light: Determines whether to set
the indicator light on the front of the TV to
On or Off in standby mode.
ꔛ Power Light: Determines whether to set the
indicator light on the front of the TV to On
or Off when the power turns on.
ꔛ
111
PICTURE CONTROL
TRUMOTION
-F
or 32/37/42/47/55LE5300, 42/47/55LE7300, 32/42/47/55LD520, 55LD520C,
42/47/55LD630, 42/47/55LE530C
Advance video technology that provides clearer, smoother images, even during fast action scenes creating a more stable structure for a crisper picture.
PICTURE
ꔂ Move
ꔉ Enter
• Sharpness
70
• Color
60
• Tint
0
R
G
• Color Temp.
0
W
C
• Advanced Control
• Picture Reset
• TruMotion
: Low
TruMotion
◀
• Judder
5
• Blur
5
Low
▶
� Enter
ꔉ
ꔀ
• Screen (RGB-PC)
PICTURE CONTROL
1
2
3
Select PICTURE.
MENU
ENTER
Select TruMotion.
ENTER
Select Low, High, User, or Off.
Adjustment for TruMotion (Judder
and Blur) with selecting User
4
5
Make appropriate adjustments.
6
RETURN
EXIT
112
Select Judder or Blur.
ENTER
or
BACK
Return to the previous menu.
Return to TV viewing.
Off: Turn off TruMotion operation.
Low: Provides smooth picture movement. Use this setting for standard
use.
ꔛ High:
Provides smoother picture
movement.
ꔛ Judder: Adjusts noise of the screen.
ꔛ Blur: Adjusts after-image of the screen.
ꔛ TruMotion works with all inputs except
PC mode.
ꔛ If you enable "TruMotion", noise may
appear on the screen. If this occurs,
set "TruMotion" to "Off".
ꔛ If you select "Picture Mode-Game"
set "TruMotion" to "Off".
ꔛ
ꔛ
SOUND
& LANGUAGE CONTROL
AUTO VOLUME
Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program.
Because each broadcasting station has its own signal conditions, volume adjustment may be needed
every time the channel is changed. This feature allows users to enjoy stable volume levels by making
automatic adjustments for each program.
AUDIO
ꔂ Move
• Auto Volume
: Off
• Clear Voice II
: Off � 3
• Balance
2
3
ꔉ
ꔡ
0
: Off � 3
• Balance
0
ꔑ On
• Sound Mode
: Standard
• Infinite Sound:Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
ENTER
Select On or Off.
BACK
Return to the previous menu.
Return to TV viewing.
ꔉ Enter
□ Off
• Infinite Sound:Off
Select Auto Volume.
EXIT
: On
• Clear Voice II
: Standard
ENTER
or
• Auto Volume
Select AUDIO.
RETURN
R
ꔂ Move
• Sound Mode
MENU
4
L
AUDIO
L
R
ꔠ
ꔉ
SOUND & LANGUAGE CONTROL
1
ꔉ Enter
113
SOUND & LANGUAGE CONTROL
CLEAR VOICE II
By differentiating the human sound range from others, it improves the sound quality of voices.
AUDIO
ꔂ Move
• Auto Volume
: Off
• Clear Voice II
: Off � 3
• Balance
1
SOUND & LANGUAGE CONTROL
2
3
: Standard
ꔉ
ꔀ
0
L
R
• Infinite Sound:Off
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
Adjustment for Clear Voice Level
with selecting On
Select Level.
Make appropriate adjustments.
BACK
Return to the previous menu.
Return to TV viewing.
ꔉ Enter
• Clear Voice II
L
0• Level
Select On or Off.
EXIT
: Off � 3
• Balance
50
ENTER
or
: Off
• Clear Voice II
• Treble
Select Clear Voice II.
RETURN
• Auto Volume
• Infinite Sound:Off
ENTER
5
ꔂ Move
: Standard
Select AUDIO.
4
AUDIO
• Sound Mode
MENU
6
114
• Sound Mode
ꔉ Enter
R
◀
�3
Close
-
Off
▶
+
BALANCE
Adjust the left/right sound of speaker to suit your taste and room situations.
AUDIO
ꔂ Move
3
: Off
• Auto Volume
: Off
• Clear Voice II
: Off � 3
• Clear Voice II
: Off � 3
0
L
ꔀ
R ꔉ
: Standard
• Sound Mode
: Standard
• Infinite Sound:Off
• Infinite Sound:Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
ENTER
Select Balance.
ENTER
Make appropriate adjustments.
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
ꔉ Enter
• Balance
0 ◀
L
R
0ꔉ
Select AUDIO.
RETURN
• Balance
• Sound Mode
MENU
4
ꔂ Move
L
R
▶
Close
SOUND & LANGUAGE CONTROL
2
AUDIO
• Auto Volume
• Balance
1
ꔉ Enter
115
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS (SOUND MODE)
Sound Mode lets you enjoy the best sound without any special adjustment using factory presets.
AUDIO
ꔂ Move
SOUND & LANGUAGE CONTROL
116
2
3
: Off
• Auto Volume
: Off
: Off � 3
• Clear Voice II
: Off � 3
0
L
R
ꔉ
ꔀ
: Standard
• Infinite Sound:Off
• Treble
50
• Bass
50
• Bass
• Reset
• Reset
ENTER
Select Sound Mode.
ENTER
Select Standard, Music, Cinema,
Sport, or Game.
EXIT
or
• Balance
• Sound Mode
Select AUDIO.
RETURN
ꔂ Move
• Clear Voice II
MENU
4
AUDIO
• Auto Volume
• Balance
1
ꔉ Enter
BACK
Return to the previous menu.
Return to TV viewing.
• Sound Mode
: Standard
ꔉ Enter
ꔑ Standard
L
□0 Music
ꔉ
R
ꔡ
□ Cinema
• Infinite Sound□
:OffSport
• Treble
50 Game
□
50
Standard, Music, Cinema, Sport, and
Game are preset for optimum sound
quality at the factory.
ꔛ You can also adjust Sound Mode in
the Q.MENU.
ꔛ Standard:
Offers standard-quality
sound.
ꔛ Music: Optimizes sound for listening
to music.
ꔛ Cinema: Optimizes sound for watching movies.
ꔛ Sport: Optimizes sound for watching
sports events.
ꔛ Game: Optimizes sound for playing
games.
ꔛ
SOUND SETTING ADJUSTMENT - USER MODE
Adjust the sound to suit your taste and room situations.
AUDIO
ꔂ Move
ꔉ Enter
AUDIO
ꔂ Move
• Auto Volume
: Off
• Auto Volume
: Off
• Clear Voice II
: Off � 3
• Clear Voice II
: Off � 3
• Balance
0
L
R
• Balance
0
ꔉ Enter
L
R
• Sound Mode
: Standard
• Sound Mode
• Infinite Sound:Off
• Infinite Sound
• Infinite Sound:Off
• Treble
50
• Treble
• Bass
50
• Bass
• Reset
• Reset
ꔉ
ꔀ
: Standard
50 • Treble
50 • Bass
Off
50
◀
▶
50
Close
1
3
4
5
If sound quality or volume is not at
the level you want, it is recommended
to use a separate home theater system or amp to cope with different
user environments.
ꔛ If you select “Clear Voice II-On”, the
Infinite Sound feature will not operate.
ꔛ Infinite Sound: Infinite Sound is a
patented LG proprietary sound processing technology that strives
immersive 5.1 surround sound with
just two front speakers.
ꔛ
ENTER
Select Sound Mode.
ENTER
Select Standard, Music, Cinema,
Sport, or Game.
ENTER
Select Infinite Sound, Treble, or Bass.
ENTER
Make appropriate adjustments.
6
RETURN
EXIT
or
BACK
Return to the previous menu.
SOUND & LANGUAGE CONTROL
2
Select AUDIO.
MENU
Return to TV viewing.
117
SOUND & LANGUAGE CONTROL
AUDIO RESET
Settings of the selected Sound Mode return to the default factory settings.
AUDIO
ꔂ Move
• Clear Voice II
• TV Speaker
SOUND & LANGUAGE CONTROL
1
2
3
4
• Reset
: On
Select AUDIO.
ENTER
Select Reset.
ENTER
Select Yes.
EXIT
118
• Bass
Yes
MENU
ENTER
0
L
R
: Standard
ꔉ
ꔀ
i
ꔉ Enter
: Off � 3
• Balance
50
No
Initialize the adjusted value.
Return to TV viewing.
ꔂ Move
• Sound Mode
• Infinite Sound:Off
? All audio settings will be resetted.
50
Continue?• Treble
AUDIO
• Clear Voice II
• Balance
• Sound Mode
ꔉ Enter
: Off � 3
0
L
: Standard
• Infinite Sound:Off
Resetting audio configuration...
• Treble
50
• Bass
• Reset
• TV Speaker
: On
50
R
TV SPEAKERS ON/OFF SETUP
If you wish to use an external Hi-Fi system, turn off the TV’s internal speakers.
AUDIO
ꔂ Move
• Clear Voice II
2
3
AUDIO
: Off � 3
0
• Sound Mode
: Standard
ꔂ Move
• Clear Voice II
• Balance
1
ꔉ Enter
L
: Off � 3
• Balance
R
0
• Sound Mode
: Standard
• Infinite Sound:Off
• Infinite Sound:Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
• TV Speaker
: On
• TV Speaker
: On
ꔠ
ꔉ
4
Select AUDIO.
MENU
RETURN
Select TV Speaker.
ENTER
EXIT
ꔉ Enter
or
BACK
L
R
□ Off
ꔠ
ꔉ
ꔑ On
Return to the previous menu.
Return to TV viewing.
Select On or Off.
ENTER
SOUND & LANGUAGE CONTROL
EXTERNAL SPEAKERS ON/OFF SETUP
(For 32/37/42/47LD450C, 32/37/47/47LD452C, 32/42/47LD452B, 26LD352C)
Turn the external speakers on if using external audio equipment.
AUDIO
ꔂ Move
• Balance
ꔠ
• Sound Mode
: Standard
0
ꔉ Enter
L
2
3
• Infinite Sound:Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
• TV Speaker
: On
• TV Speaker
: On
ENTER
Select Exrernal Speaker.
ENTER
Select On or Off.
EXIT
or
0
• Infinite Sound:Off
Select AUDIO.
RETURN
• Balance
: Standard
MENU
4
ꔂ Move
ꔠ
• Sound Mode
• External Speaker : Off
1
R
AUDIO
BACK
ꔠ
ꔉ
• External Speaker : Off
L
□ Off
ꔑ On
ꔉ Enter
R
ꔠ
ꔉ
ꔠ
ꔉ
Return to the previous menu.
Return to TV viewing.
119
SOUND & LANGUAGE CONTROL
STEREO/SAP BROADCAST SETUP
On analog signals, this TV can receive MTS stereo programs and any SAP (Secondary Audio
Program) that accompanies the stereo program if the station transmits an additional sound signal.
Mono sound is automatically used if the broadcast is only in Mono.
◀
Multi Audio
▶
English ꔉ
A
SOUND & LANGUAGE CONTROL
ꕉ Exit
Analog TV
1
2
Q.MENU
Select SAP.
ENTER
Select Mono, Stereo, or
SAP.
3
EXIT
120
Digital TV
Return to TV viewing.
1
2
Q.MENU
Select Multi Audio.
ENTER
Select other languages.
3
EXIT
Return to TV viewing.
AUDIO LANGUAGE
This feature operates only in DTV/Cable DTV mode.
OPTION
ꔂ Move
ꔉ Enter
• Language
• Caption
ꔉ
: Off
ꔡ
• Power Indicator
3
• Initial Setting
:1
• Mode Setting
: Home Use
• Mode Setting
: Home Use
Select Language.
ENTER
Select Audio Language.
Select your desired language.
EXIT
or
BACK
English
Audio Language
◀ English ▶
Close
• Set ID
ENTER
RETURN
: Off
:1
Select OPTION.
5
• Caption
• Set ID
MENU
4
• Language
ꔉ Enter
Menu Language
SOUND & LANGUAGE CONTROL
2
ꔂ Move
• Power Indicator
• Initial Setting
1
OPTION
Return to the previous menu.
Return to TV viewing.
121
SOUND & LANGUAGE CONTROL
ON-SCREEN MENUS LANGUAGE SELECTION
The menus can be shown on the screen in the selected language.
OPTION
ꔂ Move
• Language
• Caption
ꔉ Enter
ꔉ
: Off
ꔡ
• Power Indicator
SOUND & LANGUAGE CONTROL
2
3
:1
• Mode Setting
: Home Use
• Mode Setting
: Home Use
ENTER
Select Menu Language.
Select your desired language.
From this point on, the on-screen menus
will be shown in the selected language.
EXIT
122
• Set ID
Select Language.
or
: Off
• Initial Setting
ENTER
RETURN
• Caption
:1
Select OPTION.
5
• Language
• Set ID
MENU
4
ꔂ Move
• Power Indicator
• Initial Setting
1
OPTION
BACK
Return to the previous menu.
Return to TV viewing.
ꔉ Enter
Menu Language
◀ English ▶
Audio Language
English
Close
CAPTION MODE
Analog Broadcasting System Captions
Captions are provided to help the hearing impaired watch TV. Select a caption mode for displaying
captioning information if provided on a program. Analog caption displays information at any position
on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would
be available for both digital and analog channels on the Antenna/Cable. This TV is programmed to
memorize the caption/text mode which was last set when you turned the power off. This function is
only available when Caption Mode is set On.
OPTION
ꔂ Move
ꔉ Enter
• Language
• Caption
ꔉ
ꔀ
:1
• Set ID
:1
• Mode Setting
: Home Use
• Mode Setting
: Home Use
Select OPTION.
ENTER
Select Caption.
ENTER
Select On.
Select CC1-4 or Text1-4.
5
RETURN
EXIT
or
BACK
Return to the previous menu.
◀
On
Mode
▶
CC1
Digital Option
• Initial Setting
• Set ID
MENU
4
: CC1
ꔉ Enter
Close
When selecting Off, Sub-menus for
Analog, DTV, and Digital Option
become disabled.
ꔛ Caption
The term for the words that scroll
across the bottom of the TV screen;
usually the audio portion of the program provided for the hearing
impaired.
ꔛ Text
The term for the words that appear in
a large black frame and almost cover
the entire screen; usually messages
provided by the broadcaster.
ꔛ
SOUND & LANGUAGE CONTROL
3
• Caption
• Power Indicator
• Initial Setting
2
ꔂ Move
• Language
: Off
• Power Indicator
1
OPTION
Return to TV viewing.
123
SOUND & LANGUAGE CONTROL
Digital Broadcasting System Captions
Choose the language you want the DTV/Cable DTV Captions to appear in.
Other Languages can be chosen for digital sources only if they are included on the program.
This function in only available when Caption Mode is set On.
OPTION
ꔂ Move
ꔉ Enter
• Language
• Caption
ꔉ
ꔀ
SOUND & LANGUAGE CONTROL
3
:1
• Mode Setting
: Home Use
• Mode Setting
: Home Use
Select Caption.
ENTER
Select On.
Select CC1-4, Text1-4, or Service1 - 6.
RETURN
EXIT
124
• Set ID
ENTER
or
BACK
Return to the previous menu.
Return to TV viewing.
ꔉ Enter
On
Mode
▶
CC1
Digital Option
• Initial Setting
:1
Select OPTION.
5
◀
: CC1
• Set ID
MENU
4
• Caption
• Power Indicator
• Initial Setting
2
ꔂ Move
• Language
: Off
• Power Indicator
1
OPTION
Close
Caption Option
Customize the DTV/Cable DTV captions that appear on your screen.
This function in only available when Caption Mode is set On.
◀
OPTION
ꔂ Move
ꔉ Enter
: CC1
◀
• Initial Setting
Font 1
Text Color
• Power Indicator
On
Mode
• Set ID
:1
• Mode Setting
: Home Use
■ White
Text Opacity
▶
Solid
Bg Color
CC1
Digital Option
Close
▶
A Standard
Font
• Language
• Caption
Custom
Size
■ Black
Bg Opacity
Solid
Edge Type
None
Edge Color
■ Black
Close
Select OPTION.
MENU
Size: Set the word size.
Font: Select a typeface for the text.
ꔛ Text Color: Choose a color for the
text.
ꔛ Text Opacity: Specify the opacity for
the text color.
ꔛ Bg (Background) Color: Select a
background color.
ꔛ Bg (Background) Opacity: Select the
opacity for the background color.
ꔛ Edge Type: Select an edge type.
ꔛ Edge Color: Select a color for the
edges.
ꔛ
ꔛ
2
3
ENTER
Select Caption.
ENTER
Select On.
4
5
Select Digital Option.
Select Custom.
ENTER
SOUND & LANGUAGE CONTROL
1
Customize the Size, Font, etc., to your
preference. A preview icon is provided
at the bottom of the screen, use it to
see the caption language.
6
7
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
125
TIME
TIME SETTING
SETTING
CLOCK SETTING
Auto Clock Setup
The time is set automatically from a digital channel signal.
The digital channel signal includes information for the current time provided by the broadcasting station.
Set the clock manually if the current time is set incorrectly by the auto clock function.
TIME
ꔂ Move
• Clock
• Off Time
: Off
• On TIme
• Sleep Timer
• Auto Off
ꔉ Enter
TIME
ꔉ
• Clock
ꔡ
ꔂ Move
ꔉ Enter
◀
Auto
: Off
: Off
• On TIme
: Off
: Off
• Sleep Timer
: Off
Date
21
: On
• Auto Off
: On
Year
2010
Hour
10 AM
Month
02
Minute
10
Time Zone
Eastern
Daylight Saving
Auto
Close
TIME SETTING
1
2
3
MENU
Select TIME.
ENTER
Select Clock.
ENTER
Select Auto.
4
Select your viewing area time zone.
USA: Eastern, Central, Mountain,
Pacific, Alaska, or Hawaii.
Canada: Eastern, Central, Mountain,
Pacific, New Foundland, or Atlantic.
5
Select Auto, Off, or On (depending
on whether or not your viewing area
observes Daylight Saving time).
6
RETURN
EXIT
126
or
BACK
▶
• Off Time
Return to the previous menu.
Return to TV viewing.
Manual Clock Setup
If the current time setting is wrong, reset the clock manually.
TIME
ꔂ Move
• Clock
• Off Time
: Off
• On TIme
• Sleep Timer
• Auto Off
ꔉ Enter
TIME
ꔉ
• Clock
ꔡ
ꔂ Move
ꔉ Enter
◀
Manual
▶
• Off Time
: Off
: Off
• On TIme
: Off
: Off
• Sleep Timer
: Off
Date
21
: On
• Auto Off
: On
Year
2010
Hour
10 AM
Month
02
Minute
10
Time Zone
Eastern
Daylight Saving
Auto
Close
2
3
MENU
Select TIME.
ENTER
Select Clock.
ENTER
Select Manual.
4
TIME SETTING
1
Select the Year, Month, Date, Hour, or Minute
option.
5
Set the Year, Month, Date, Hour, or Minute
option.
6
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
127
TIME SETTING
AUTO ON/OFF TIME SETTING
This function operates only if the current time has been set.
The Off Time function overrides the On Time function if they are both set to the same time.
The TV must be in standby mode for the On Time to work.
If you do not press any button within 2 hours after the TV turns on with the On Time function, the TV
will automatically revert to standby mode. (Except 42/47LD450C, 55LD520C, 42/47/55LE530C,
42/47LD452C, 42/47LD452B, 26LD352C)
TIME
ꔂ Move
TIME
ꔉ Enter
• Clock
ꔂ Move
ꔉ Enter
• Clock
• Off Time
: Off
• On TIme
: Off
• Sleep Timer
: Off
• Sleep Timer
• Auto Off
: On
• Auto Off
ꔉ
ꔀ
ꔎ Feb. 21, 2010 10:10 AM
• Off Time
: Off
• On TIme
: 6:30 AM (Once)ꔉ
Repeat
: Off
Hour
: On
Minute
◀ Once ▶
6 AM
30
Input
TV
Channel
TV 2-0
Volume
30
Close
TIME SETTING
1
2
3
Select TIME.
ENTER
Select Off Time or On Time.
1
ENTER
Select Repeat.
2
4
Select Off, Once, Daily, Mon.~Fri.,
Mon.~Sat., Sat.~ Sun., or Sun..
5
Select and set Hour or Minute.
6
RETURN
EXIT
128
To cancel On/Off Time function, select
Off.
ꔛ Only for On Time function
ꔛ
MENU
or
BACK
Return to the previous menu.
Return to TV viewing.
3
4
Select Input.
Select the desired input source.
When Selecting TV:
set the channel at turn-on.
Adjust to sound level at
turn-on.
SLEEP TIMER SETTING
The Sleep Timer turns the TV off at the preset time.
Note that this setting is cleared when the TV is turned off.
TIME
ꔂ Move
TIME
ꔉ Enter
• Clock
ꔂ Move
ꔉ Enter
• Clock
• Off Time
: Off
• Off Time
: Off
• On TIme
: Off
• On TIme
: Off
• Sleep Timer
: Off
• Sleep Timer
: Off
• Auto Off
: On
• Auto Off
: On
ꔠ
ꔉ
ꔑ Off
ꔉ
ꔡ
□ 10 min.
□ 20 min.
□ 30 min.
□ 60 min.
□ 90 min.
□ 120 min.
□ 180 min.
□ 240 min.
1
2
3
4
MENU
Select TIME.
ENTER
Select Sleep Timer.
ENTER
Make appropriate adjustments.
RETURN
or
BACK
Return to the previous menu.
Return to TV viewing.
EXIT
ꔛ
ꔛ
AUTO SHUT-OFF SETTING
For 37/42/47LD450C, 55LD520C, 42/47LD451C, 32/37/42/47LD452C, 32/42/47LD452B, 26LD352C
If set to on and there is no input signal, the TV turns off automatically after 15 minutes.
TIME
ꔂ Move
TIME
ꔉ Enter
ꔂ Move
ꔉ Enter
• Clock
• Clock
• Off Time
: Off
• Off Time
: Off
• On TIme
: Off
• On TIme
: Off
• Sleep Timer
: Off
• Sleep Timer
: Off
• Auto Off
: On
• Auto Off
: On
ꔠ
ꔉ
□ Off
ꔠ
ꔉ
ꔑ On
1
2
3
TIME SETTING
To cancel the Sleep Timer, select Off.
You can also adjust Sleep Timer in
the Q.MENU.
MENU
Select TIME.
ENTER
Select Auto Off.
ENTER
Select On or Off.
4
RETURN
EXIT
or
BACK
ꔠ
ꔉ
Return to the previous menu.
Return to TV viewing.
129
PARENTAL
CONTROL
/ RATINGS
PARENTAL CONTROL
/ RATINGS
Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by
the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be
blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done :
1. Set ratings and categories to be blocked.
2. Specify a password
3. Enable the lock
V-Chip rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the
theaters or direct-to-video movies use the Movie Rating System (MPAA) only.
Ratings for Television programs including made-for-TV movies:
TV-G (General audience)
TV-PG(Parental guidance suggested)
ꔛ TV-14 (Parents strongly cautioned)
ꔛ TV-MA (Mature audience only)
ꔛ TV-Y (All children)
ꔛ TV-Y7 (Children 7 years older)
ꔛ
ꔛ
SET PASSWORD & LOCK SYSTEM
PARENTAL CONTROL / RATING
Setting up Your Password
Set up blocking schemes to block specific channels, ratings, and external viewing sources.
A password is required to gain access to this menu.
LOCK
• Set Password
1
2
MENU
1
2
3
4
5
6
7
8
9
0
130
ꔂ Move
ꔉ
• Lock System
: On
• Block Channel
• Movie Rating
• TV Rating-Children
• TV Rating-General
• Downloadable Rating
• Input Block
ENTER
ꔉ Enter
Select LOCK.
Input the password.
ꔡ
Enter Password
*
*
*
*
Close
Enter the password as requested.
The TV is set up with the initial
password “0-0-0-0”.
ꔛ If you forget your password, press
“0-3-2-5” on the remote control.
ꔛ
ꔛ
Set Password
Change the password by inputting a new password twice.
LOCK
ꔂ Move
ꔉ Enter
• Set Password
1
2
: On
2
3
4
5
6
7
8
9
ꔡ
ꔂ Move
• Set Password
New
• Lock System
: On
• Block Channel
• Block Channel Confirm
• Movie Rating
• Movie Rating
• TV Rating-Children
• TV Rating-Children
• TV Rating-General
• TV Rating-General
• Downloadable Rating
• Downloadable Rating
• Input Block
• Input Block
ENTER
MENU
1
ꔉ
• Lock System
LOCK
ꔉ Enter
*
*
*
*
*
*
*
*
Close
Select LOCK.
Input the password.
0
3
1
ENTER
2
5
6
8
9
0
5
RETURN
EXIT
3
4
7
or
Choose any 4 digits for your new
password.
As soon as the 4 digits are entered,
re-enter the same 4 digits on the
Confirm.
BACK
Return to the previous menu.
Return to TV viewing.
PARENTAL CONTROL / RATING
4
Select Set Password.
131
PARENTAL CONTROL / RATINGS
Lock System
Enables or disables the blocking scheme you set up previously.
LOCK
ꔂ Move
ꔉ Enter
• Set Password
1
2
2
3
4
5
6
7
8
9
• Set Password
PARENTAL CONTROL / RATING
132
4
• Block Channel
□ Off
: Onꔉ
ꔑ On
• Block Channel
• Movie Rating
• Movie Rating
• TV Rating-Children
• TV Rating-Children
• TV Rating-General
• TV Rating-General
• Downloadable Rating
• Downloadable Rating
• Input Block
• Input Block
ENTER
ꔉ
ꔀ
Select LOCK.
Input the password.
Select Lock System.
Select On or Off.
ENTER
5
RETURN
EXIT
or
ꔉ Enter
: On
0
3
ꔂ Move
• Lock System
MENU
1
LOCK
BACK
Return to the previous menu.
Return to TV viewing.
• Lock System
ꔛ
ꔠ
ꔉ
When you select On, the Lock
System is enable.
CHANNEL BLOCKING
Blocks any channels that you do not want to watch or that you do not want your children to watch.
Block Channel
LOCK
ꔂ Move
• Set Password
Favorite Group:
DTV
ꔉ Enter
3-1
• Lock System
: On
• Block Channel
• Movie Rating
• TV Rating-Children
• TV Rating-General
• Downloadable Rating
• Input Block
A
TV
page 1/1
Cable DTV
Cable TV
5-1
7-1
ꔉ
ꔀ
ꔉ CH.Change
ꔂ Navigation
ꘃ Page Change
ꕉ Previous
ꔅ Block/Unblock
1
ENTER
MENU
2
2
3
4
5
6
7
1
8
9
Select LOCK.
ꔛ
If a channel is locked, enter the
password to unlock it temporarily.
Input the password.
0
3
4
Select Block Channel.
Select a channel to block or unblock.
ENTER
YELLOW
6
RETURN
EXIT
Block or unblock a channel.
or
BACK
Return to the previous menu.
Return to TV viewing.
PARENTAL CONTROL / RATING
5
133
PARENTAL CONTROL / RATINGS
MOVIE & TV RATING
Movie Rating (MPAA)- For USA
Blocks movies according to the movie ratings limits specified, so children cannot view certain movies.
You can set the ratings limit by blocking out all the movies with the ratings above a specified level.
Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such
as soap operas.
LOCK
ꔂ Move
ꔉ Enter
• Set Password
LOCK
ꔂ Move
• Set Password
• Lock System
: On
• Block Channel
• Movie Rating
• TV Rating-Children
• TV Rating-General
• Downloadable Rating
• Input Block
ꔉ
ꔀ
• Lock System
: On
• Block Channel
• Movie Rating
ꔉ Enter
Blocking off : Permits all
programs
G
PG
• TV Rating-Children
PG-13
• TV Rating-General
R
• Downloadable Rating
NC-17
• Input Block
X
Blocking Off ꔓ
1
2
ENTER
MENU
1
2
3
4
5
6
7
8
9
Select LOCK.
Input the password.
0
PARENTAL CONTROL / RATING
134
3
4
Select Movie Rating.
Select G, PG, PG-13, R, NC-17, X, or
Blocking Off.
ENTER
5
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
If Movie Rating, TV Rating-Children
or TV Rating-General is locked, enter
the password to unlock it temporarily.
ꔛ G (General audience)
ꔛ PG (Parental guidance suggested)
ꔛ PG-13 (Parents strongly cautioned)
ꔛ R (Restricted)
ꔛ NC-17 (No one 17 and under admitted)
ꔛ X (Adult only)
ꔛ Blocking Off (Permits all programs)
ꔛ If you set PG-13: G and PG movies
will be available, PG-13, R, NC-17 and
X will be blocked.
ꔛ
TV Rating Children
- For USA
revents children from watching certain children's TV programs, according to the ratings limit set. The
P
children rating does not apply to other TV programs. Unless you block certain TV programs intended
for mature audiences in the TV Rating - sub menu, your children can view those programs.
LOCK
ꔂ Move
ꔉ Enter
• Set Password
1
2
LOCK
: On
• Lock System
: On
• Block Channel
• Block Channel
• Movie Rating
• Movie Rating
• TV Rating-Children
• TV Rating-Children
• TV Rating-General
• TV Rating-General
• Downloadable Rating
• Downloadable Rating
• Input Block
• Input Block
ENTER
ꔉ
ꔀ
Select LOCK.
ꔛ
ꔛ
1
2
3
4
5
6
8
9
ꔉ Enter
• Set Password
• Lock System
MENU
7
ꔂ Move
Age
ꔉ
Fantasy Violence
Close
Age (applies to TV-Y, TV-Y7)
Fantasy Violence (applies to TV-Y7)
Input the password.
0
4
5
Select TV Rating-Children.
ENTER
Select Age or Fantasy Violence.
ENTER
Select block options.
6
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
PARENTAL CONTROL / RATING
3
135
PARENTAL CONTROL / RATINGS
TV Rating General
- For USA
Based on the ratings, blocks certain TV programs that you and your family do not want to view.
LOCK
ꔂ Move
ꔉ Enter
• Set Password
1
2
2
3
4
5
6
7
8
9
PARENTAL CONTROL / RATING
136
4
5
• Set Password
• Lock System
: On
• Block Channel
• Block Channel
• Movie Rating
• Movie Rating
• TV Rating-Children
• TV Rating-General
• Downloadable Rating
• TV Rating-General Violence
• Downloadable Rating
• Input Block
• Input Block
ENTER
ꔉ
ꔀ
Select LOCK.
Input the password.
Select TV Rating-General.
ENTER
Select Age, Dialogue, Language, Sex
or Violence.
ENTER
Select block options.
6
RETURN
EXIT
or
ꔉ Enter
: On
0
3
ꔂ Move
• Lock System
MENU
1
LOCK
BACK
Return to the previous menu.
Return to TV viewing.
Age
ꔉ
Dialogue
Language
• TV Rating-Children Sex
Close
Age (applies to TV-G,T V-PG,T V14,TV-MA).
ꔛ Dialogue-sexual dialogue (applies to
TV-PG,TV-14).
ꔛ Language-adult language (applies to
TV-PG, TV-14, TV-MA).
ꔛ Sex-sexual
situations (applies to
TV-PG, TV-14, TV-MA).
ꔛ Violence (applies to TV-PG, TV-14,
TV-MA).
ꔛ
TV Rating English
- For CANADA
Selecting Canadian English rating system.
LOCK
ꔂ Move
ꔉ Enter
• Set Password
LOCK
ꔂ Move
ꔉ Enter
• Set Password
• Lock System
: On
• Lock System
: On
• Block Channel
• Block Channel
• TV Rating-English
• TV Rating-French
• Downloadable Rating
• TV Rating-English E
• TV Rating-French C
• Input Block
• Key Lock
: Off
• Key Lock
ꔉ
ꔀ
Blocking off : Permits all
programs
• Downloadable Rating
C8+
• Input Block
: Off
G
PG
14+
18+
Blocking Off ꔓ
1
2
ENTER
MENU
2
3
4
5
6
7
1
8
9
Select LOCK.
Input the password.
0
3
Select E, C, C8+, G, PG, 14+, 18+, or
Blocking Off.
ENTER
5
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
PARENTAL CONTROL / RATING
4
Select TV Rating-English.
If TV Rating-English or TV RatingFrench is locked, enter the password
to unlocked it temporarily.
ꔛ E (Exempt)
ꔛ C (Children)
ꔛ C8+ (Children eight years and older)
ꔛ G (General programming, suitable
for all audiences)
ꔛ PG (Parental Guidance)
ꔛ 14+ (Viewers 14 years and older)
ꔛ 18+ (Adult programming)
ꔛ Blocking Off (Permits all programs)
ꔛ
137
PARENTAL CONTROL / RATINGS
TV Rating French
- For CANADA
Selecting Canadian French rating system.
LOCK
ꔂ Move
ꔉ Enter
• Set Password
LOCK
ꔂ Move
• Set Password
ꔉ Enter
Blocking off : Permits all
programs
• Lock System
: On
• Lock System
: On
• Block Channel
• Block Channel
• TV Rating-English
• TV Rating-French
• TV Rating-English E
• TV Rating-French G
• Downloadable Rating
• Input Block
8ans+
• Downloadable Rating
13ans+
• Input Block
• Key Lock
: Off
• Key Lock
: Off
ꔉ
ꔀ
16ans+
18ans+
Blocking Off ꔓ
1
ENTER
MENU
Select LOCK.
E (Exempt)
G (General)
ꔛ 8ans+ (General-Not convenient for
little children)
ꔛ 13ans+ (Not convenient for children
of 13 years and younger)
ꔛ 16ans+ (Not convenient for children
of 16 years and younger)
ꔛ 18ans+ (This programs is only for
adults)
ꔛ Blocking Off (Permits all programs)
ꔛ
ꔛ
2
1
2
3
4
5
6
7
8
9
Input the password.
0
3
PARENTAL CONTROL / RATING
138
4
Select TV Rating-French.
Select E, G, 8ans+, 13ans+, 16ans+,
18ans+, or Blocking Off.
ENTER
5
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
DOWNLOADABLE RATING
This
function is available only for digital channels.
This function operates only when TV has received Region5 Rating data.
LOCK
ꔂ Move
ꔉ Enter
• Set Password
LOCK
ꔂ Move
ꔉ Enter
• Set Password
• Lock System
: On
• Lock System
: On
• Block Channel
• Block Channel
• Movie Rating
• Movie Rating
• TV Rating-Children
• TV Rating-General
• Downloadable Rating
• Input Block
ꔉ
Sport
Cruelty
• TV Rating-Children
Language
• TV Rating-General
Sadness
• Downloadable Rating
Genre
• Input Block
Age
ꔉ
ꔀ
Humor
ꔍ
Close
ꔛ
1
2
3
4
5
6
7
1
8
9
Select LOCK.
Input the password.
0
3
4
5
Select Downloadable Rating.
ENTER
Select desired Downloadable Rating
option.
ENTER
Select desired option and block it.
6
RETURN
EXIT
or
BACK
Return to the previous menu.
ꔛ
If a Downloadable rating is locked,
enter the password to unlock it temporarily.
PARENTAL CONTROL / RATING
2
ENTER
MENU
Based on rating table, your TV's
OSD (On Screen Display) may differ slightly from what is shown in
this manual.
Return to TV viewing.
139
PARENTAL CONTROL / RATINGS
EXTERNAL INPUT BLOCKING
Enables you to block an input.
LOCK
ꔂ Move
ꔉ Enter
LOCK
ꔂ Move
• Lock System
: On
• Lock System
• Block Channel
• AV
• Block Channel
• Movie Rating
• Component
• Movie
Rating
• TV Rating-Children
• TV Rating-General
• TV Rating-Children
• RGB-PC
• Downloadable Rating
• Input Block
: On
• Key Lock
: Off
◀
Off
• Key Lock
: Off • HDMI3
Off
i.e)
2
ENTER
MENU
1
2
3
4
5
6
7
8
9
Select LOCK.
Input the password.
0
PARENTAL CONTROL / RATING
140
3
4
Select Input Block.
Select input source.
ENTER
5
Select On or Off.
6
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
Off
Close
1
Off
Off
• TV Rating-General
• HDMI1
• Downloadable Rating
• HDMI2
• Input
Block
ꔉ
ꔀ
ꔉ Enter
Off
▶
KEY LOCK
This feature can be used to prevent unauthorized viewing by locking out the front panel controls, so
that it can only be used with the remote control.
This TV is programmed to remember which option it was last set to even if you turn the TV off.
LOCK
1
2
• Lock System
: On
• Block Channel
• Movie Rating
• TV Rating-Children
• TV Rating-General
• Downloadable Rating
• Input Block
• Key Lock
: Off
ENTER
MENU
2
3
4
5
6
7
1
8
9
ꔂ Move
ꔉ Enter
ꔠ
ꔉ
Select LOCK.
Input the password.
0
4
Select LOCK.
Select On or Off.
ENTER
5
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
ꔂ Move
• Lock System
: On
• Block Channel
• Movie Rating
• TV Rating-Children
• TV Rating-General
• Downloadable Rating
• Input Block
• Key Lock
: Off
ꔉ Enter
□ Off
ꔑ On
ꔠ
ꔉ
In Key Lock ‘On’, if the TV is turned
off, press the / I, INPUT, CH (ꔌꔍor
ꕌꕍ) button on the TV or POWER,
INPUT, CH (ꕌꕍ) or NUMBER buttons on the remote control.
ꔛ With the Key Lock On, the display
‘ ! Key Lock’ appears on the screen
if any button on the front panel is
pressed while viewing the TV.
ꔛ
PARENTAL CONTROL / RATING
3
LOCK
141
APPENDIX
APPENDIX
TROUBLESHOOTING
Abnormal Operation
Check to see if there is any object between the product and the remote
control causing obstruction. Ensure you are pointing the remote control
directly at the TV.
ꔛ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
ꔛ Ensure that the correct remote operating mode is set: TV, VCR etc.
ꔛ Install new batteries.
*This feature is not available for all models.
ꔛ
The remote control
doesn’t work
Is the sleep timer set?
Check the power control settings. Power interrupted.
ꔛ If there is no signal, the TV turns off automatically in 15 minutes.
ꔛ
TV turns off suddenly
ꔛ
Video Problems
Check whether the product is turned on.
Try another channel. The problem may be with the broadcast.
ꔛ Is the power cord inserted into wall power outlet?
ꔛ Check your antenna direction and/or location.
ꔛ Test the wall power outlet, plug another product’s power cord into the
outlet where the product’s power cord was plugged in.
ꔛ
ꔛ
No picture &No sound
Picture appears slowly
after switching on
This is normal, the image is muted during the product startup process.
Please contact your service center, if the picture has not appeared after
five minutes.
APPENDIX
Adjust Color in menu option.
Keep a sufficient distance between the product and the VCR.
ꔛ Try another channel. The problem may be with the broadcast.
ꔛ Are the video cables installed properly?
ꔛ Activate any function to restore the brightness of the picture.
ꔛ
No or poor color or
poor picture
Horizontal/vertical bars
or picture shaking
Poor reception on
some channels
Lines or streaks in pictures
No picture when connecting HDMI
142
ꔛ
ꔛ
ꔛ
Check for local interference such as an electrical appliance or power
tool.
Station or cable product experiencing problems, tune to another station.
ꔛ Station signal is weak, reorient antenna to receive weaker station.
ꔛ Check for sources of possible interference.
ꔛ
ꔛ
Check antenna (Change the direction of the antenna).
ꔛ
If an HDMI cable doesn’t support High Speed HDMI, it can cause flickers or no screen display. In this case use the latest cables that support
High Speed HDMI.
Audio Problems
No output from one
of the speakers
Unusual sound from
inside the product
No sound
when connecting
HDMI/USB
ꔛ
Adjust Balance in menu option.
ꔛ
A change in ambient humidity or temperature may result in an unusual
noise when the product is turned on or off and does not indicate a fault
with the product.
Check High Speed HDMI cable.
Check USB cable over version 2.0.
ꔛ Use normal MP3 file.
*This feature is not available for all models.
ꔛ
ꔛ
PC Mode Problems
The signal is out of
range
Vertical bar or stripe
on
background &
Horizontal Noise &
Incorrect position
Screen color is unstable or single color
ꔛ
Adjust resolution, horizontal frequency, or vertical frequency on the PC.
Check the input source.
ꔛ
Activate the Auto configure feature or adjust size, phase, or H/V position.
(Option)
ꔛ
Check the signal cable.
Reinstall the PC video card.
ꔛ
ꔛ
Check the manual for the video card in the PC to see if it supports
HDMI audio and how to set it up properly.
APPENDIX
When connecting the
HDMI cable to the PC,
there is no audio.
ꔛ
143
APPENDIX
Movie List Problems
The file does not
appear on the Movie
List.
Message is displayed
saying “This file is
invalid” or the audio is
working normally but
the video is not working normally.
Message is displayed
saying “Unsupported
Audio” or the video is
working normally but
the audio is not working normally.
ꔛ
Check whether the file is playing normally on a PC. (Check whether the
file is damaged.)
ꔛ Check whether the resolution is supported.
ꔛ Check whether the video/audio codec is supported.
ꔛ Check whether the frame rate is supported.
ꔛ
Check whether the
file is damaged.)
ꔛ Check whether the
ꔛ Check whether the
ꔛ Check whether the
ꔛ
APPENDIX
144
file is playing normally on a PC. (Check whether the
audio codec is supported.
bit rate is supported.
sample rate is supported.
Check whether the file is playing normally on a PC. (Check whether the
file is damaged.)
ꔛ Check whether the video file and subtitle file name are the same.
ꔛ Check whether the video file and subtitle file are located in the same
folder.
ꔛ Check whether the subtitle file is supported.
ꔛ Check whether the language is supported. (When you open the subtitle
file on a PC, you can check the language of the subtitle file.)
ꔛ
Subtitle is not working.
Check whether the file extension is supported.
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you
can enjoy your new TV.
Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of
lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s
almost dry, and then use it to wipe the screen.
2
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
!
?
ꔛ
!To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
ꔛ
Please be sure not to use a wet cloth.
?
Extended Absence
CAUTION
►If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to
unplug the power cord to protect against possible damage from lightning or power surges.
APPENDIX
145
APPENDIX
PRODUCT SPECIFICATIONS
MODELS
22LE5300 (22LE5300-UE)
22LE5500 (22LE5500-UA)
Dimensions
(Width x
Height
x Depth)
With stand
471.2 mm x 365.9 mm x 155.4 mm
(18.5 inch x 14.4 inch x 6.1 inch)
542.9 mm x 407.1 mm x 155.4 mm
(21.3 inch x 16.0 inch x 6.1 inch)
Without stand
471.2 mm x 315.5 mm x 34.4 mm
(18.5 inch x 12.4 inch x 1.3 inch)
542.9 mm x 357.6 mm x 34.4 mm
(21.3 inch x 14.0 inch x 1.3 inch)
Weight
With stand
3.4 kg (7.4 lbs)
4.2 kg (9.2 lbs)
Without stand
3.2 kg (7.0 lbs)
3.9 kg (8.5 lbs)
MODELS
Dimensions
(Width x
Height
x Depth)
Weight
26LE5300 (26LE5300-UE)
26LE5500 (26LE5500-UA)
With stand
652.0 mm x 480.8 mm x 191.4 mm
(25.6 inch x 18.9 inch x 7.5 inch)
Without stand
652.0 mm x 420.3 mm x 34.4 mm
(25.6 inch x 16.5 inch x 1.3 inch)
With stand
6.1 kg (13.4 lbs)
Without stand
5.1 kg (11.2 lbs)
Power Requirement
Adapter (DC Power)
19LE5300: 24V
22LE5300: 24V
22LE5500: 24V
26LE5300: 24V
26LE5500: 24V
, 1.6A
, 1.7 A
, 1.7 A
, 1.8 A
, 1.8 A
In: AC100-240 V ~ 50/60 Hz
Out: DC 24 V, 3.42 A
APPENDIX
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
Environment
condition
Operating Temperature
ꔛ The
75 Ω
0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C (-4 °F to 140 °F)
Storage Humidity
146
19LE5300 (19LE5300-UE)
Less than 85 %
specifications shown above may be changed without prior notice for quality improvement.
MODELS
32LE5300 (32LE5300-UC)
37LE5300 (37LE5300-UC)
Dimensions
(Width x
Height
x Depth)
With stand
784.6 mm x 558.1 mm x 221.0 mm
(30.8 inch x 21.9 inch x 8.7 inch)
905.0 mm x 630.0 mm x 270.0 mm
(35.6 inch x 24.8 inch x 10.6 inch)
Without stand
784.6 mm x 499.5 mm x 39.9 mm
(30.8 inch x 19.6 inch x 1.5 inch)
905.0 mm x 568.0 mm x 39.9 mm
(35.6 inch x 22.3 inch x 1.5 inch)
Weight
With stand
12.4 kg (27.3 lbs)
15.3 kg (33.7 lbs)
Without stand
10.5 kg (23.1 lbs)
12.8 kg (28.2 lbs)
1.3 A
1.4 A
42LE5300 (42LE5300-UC)
42LE530C (42LE530C-UC)
47LE5300 (47LE5300-UC)
47LE530C (47LE530C-UC)
With stand
1016.0 mm x 692.0 mm x 270.0 mm
(40.0 inch x 27.2 inch x 10.6 inch)
1126.6 mm x 757.9 mm x 284.4 mm
(44.3 inch x 29.8 inch x 11.1 inch)
Without stand
1016.0 mm x 630.0 mm x 29.3 mm
(40.0 inch x 24.8 inch x 1.1 inch)
1126.6 mm x 692.0 mm x 29.3 mm
(44.3 inch x 27.2 inch x 1.1 inch)
With stand
19.2 kg (42.3 lbs)
22.6 kg (49.8 lbs)
Without stand
16.7 kg (36.8 lbs)
19.6 kg (43.2 lbs)
1.5 A
1.7 A
Current Value
MODELS
Dimensions
(Width x
Height
x Depth)
Weight
Current Value
MODELS
Dimensions
(Width x
Height
x Depth)
With stand
Without stand
1306.0 mm x 867.0 mm x 345.0 mm
(51.4 inch x 34.1 inch x 13.5 inch)
1306.0 mm x 797.0 mm x 30.7 mm
(51.4 inch x 31.3inch x 1.2 inch)
With stand
34.05 kg (75.0 lbs)
Without stand
28.8 kg (63.4 lbs)
Current Value
2.0 A
Power Requirement
AC 120 V ~ 50 / 60 Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
Environment
condition
Operating Temperature
ꔛ The
75 Ω
0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C (-4 °F to 140 °F)
Storage Humidity
APPENDIX
Weight
55LE5300 (55LE5300-UC)
55LE530C (55LE530C-UC)
Less than 85 %
specifications shown above may be changed without prior notice for quality improvement.
147
APPENDIX
42LE7300 (42LE7300-UA)
47LE7300 (47LE7300-UA)
1009.2 mm x 694.5 mm x 286.5 mm
(39.7 inch x 27.3 inch x 11.2 inch)
1119.6 mm x 757.1 mm x 286.5 mm
(44.0 inch x 29.8 inch x 11.2 inch)
1009.2 mm x 629.7 mm x 29.3 mm
(39.7 inch x 24.7 inch x 1.1 inch)
1119.6 mm x 691.3 mm x 29.3 mm
(44.0 inch x 27.2 inch x 1.1 inch)
MODELS
Dimensions
(Width x
Height
x Depth)
With stand
Weight
With stand
25.5 kg (56.2 lbs)
29.7 kg (65.4 lbs)
Without stand
21.0 kg (46.2 lbs)
25.2 kg (55.5 lbs)
1.3 A
1.5 A
Without stand
Current Value
MODELS
Dimensions
(Width x
Height
x Depth)
With stand
1305.2 mm x 874.9 mm x 320.2 mm
(51.3 inch x 34.4 inch x 12.6 inch)
Without stand
1305.2 mm x 799.4 mm x 32.4 mm
(51.3 inch x 31.4 inch x 1.2 inch)
Weight
With stand
44.5 kg (98.1 lbs)
Without stand
37.1 kg (81.7 lbs)
Current Value
1.8 A
Power requirement
AC 120 V ~ 50 / 60 Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
Environment
condition
Operating Temperature
ꔛ The
75 Ω
0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C (-4 °F to 140 °F)
Storage Humidity
Less than 85 %
specifications shown above may be changed without prior notice for quality improvement.
APPENDIX
MODELS
Dimensions
(Width x
Height
x Depth)
With stand
Without stand
Weight
26LD352C (26LD352C-UA)
663.0 mm x 484.0 mm x 206.8 mm
(26.1 inch x 19.0 inch x 8.1 inch)
663.0 mm x 423.0 mm x 79.9 mm
(26.1 inch x 16.6 inch x 3.1 inch)
With stand
7.3 kg (16.0 lbs)
Without stand
6.2 kg (13.6 lbs)
Current Value
1.0 A
Power requirement
AC 100-240 V ~ 50 / 60 Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
Environment
condition
Operating Temperature
ꔛ The
75 Ω
0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C (-4 °F to 140 °F)
Storage Humidity
148
55LE7300 (55LE7300-UA)
Less than 85 %
specifications shown above may be changed without prior notice for quality improvement.
32LD420 (32LD420-UA)
MODEL
Dimensions
(Width x
Height
x Depth)
805.0 mm x 583.0 mm x 224.0 mm
(31.6 inch x 22.9 inch x 8.8 inch)
With stand
Without stand
Weight
805.0 mm x 531.0 mm x 79.9 mm
(31.6 inch x 20.9 inch x 3.1 inch)
With stand
10.8 kg (23.8 lbs)
Without stand
9.7 kg (21.3 lbs)
Current Value
1.4 A
42LD420 (42LD420-UA)
47LD420 (47LD420-UA)
With stand
1028.0 mm x 715.4 mm x 297.0 mm
(40.4 inch x 28.1 inch x 11.6 inch)
1140.6 mm x 784.8 mm x 337.4 mm
(44.9 inch x 30.8 inch x 13.2 inch)
Without stand
1028.0 mm x 658.6 mm x 87.8 mm
(40.4 inch x 25.9 inch x 3.4 inch)
1140.6 mm x 722.9 mm x 99.0 mm
(44.9 inch x 28.4 inch x 3.8 inch)
With stand
16.6 kg (36.5 lbs)
21.6 kg (47.6 lbs)
Without stand
14.8 kg (32.6 lbs)
19.0 kg (41.8 lbs)
MODELS
Dimensions
(Width x
Height
x Depth)
Weight
Current Value
2.6 A
37LD450 (37LD450-UA)
37LD450C (37LD450C-UA)
37LD452C (37LD452C-UA)
With stand
799.0 mm x 555.0 mm x 207.0 mm
(31.4 inch x 21.8 inch x 8.1 inch)
916.0 mm x 625.0 mm x 261.0 mm
(36.0 inch x 24.6 inch x 10.2 inch)
Without stand
799.0 mm x 506.0 mm x 73.5 mm
(31.4 inch x 19.9 inch x 2.8 inch)
916.0 mm x 575.0 mm x 77.4 mm
(36.0 inch x 22.6 inch x 3.0 inch)
With stand
9.1 kg (20.0 lbs)
12.5 kg (27.5 lbs)
Without stand
8.1 kg (17.8 lbs)
10.8 kg (23.8 lbs)
1.2 A
1.6 A
42LD450 (42LD450-UA)
42LD450C (42LD450C-UA)
42LD451C (42LD451C-UA)
42LD452C (42LD452C-UA)
42LD452B (42LD452B-UA)
47LD450 (47LD450-UA)
47LD450C (47LD450C-UA)
47LD451C (47LD451C-UA)
47LD452C (47LD452C-UA)
47LD452B (47LD452B-UA)
With stand
1023.0 mm x 685.0 mm x 261.0 mm
(40.2 inch x 26.9 inch x 10.2 inch)
1136.0 mm x 757.0 mm x 270.0 mm
(44.7 inch x 29.8 inch x 10.6 inch)
Without stand
1023.0 mm x 635.0 mm x 76.6 mm
(40.2 inch x 25.0 inch x 3.0 inch)
1136.0 mm x 698.0 mm x 76.5 mm
(44.7 inch x 27.4 inch x 3.0 inch)
With stand
15.1 kg (33.2 lbs)
19.5 kg (42.9 lbs)
Without stand
13.5 kg (29.7 lbs)
17.5 kg (38.5 lbs)
1.9 A
2.6 A
MODELS
Dimensions
(Width x
Height
x Depth)
Weight
Current Value
MODELS
Dimensions
(Width x
Height
x Depth)
Weight
Current Value
Power requirement
AC 100-240 V ~ 50 / 60 Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
Environment
condition
Operating Temperature
ꔛ The
75 Ω
0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C (-4 °F to 140 °F)
Storage Humidity
APPENDIX
1.9 A
32LD450 (32LD450-UA)
32LD452C (32LD452C-UA)
32LD452B (32LD452B-UA)
Less than 85 %
specifications shown above may be changed without prior notice for quality improvement.
149
APPENDIX
MODELS
42LD520 (42LD520-UA)
Dimensions
(Width x
Height
x Depth)
With stand
815.0 mm x 585.6 mm x 210.9 mm
(32.0 inch x 23.0 inch x 8.3 inch)
1052.2 mm x 720.1 mm x 270.6 mm
(41.4 inch x 28.3 inch x 10.6 inch)
Without stand
815.0 mm x 529.6 mm x 82.0 mm
(32.0 inch x 20.8 inch x 3.2 inch)
1052.2 mm x 657.3 mm x 90.8 mm
(41.4 inch x 25.8 inch x 3.5 inch)
Weight
With stand
12.6 kg (27.7 lbs)
19.0 kg (41.8 lbs)
Without stand
11.4 kg (25.1 lbs)
17.2 kg (37.9 lbs)
1.5 A
1.9 A
47LD520 (47LD520-UA)
55LD520 (55LD520-UA),
55LD520C (55LD520C-UA)
Current Value
MODELS
Dimensions
(Width x
Height
x Depth)
With stand
1173.4 mm x 791.4 mm x 319.0 mm
(46.1 inch x 31.1 inch x 12.5 inch)
1357.0 mm x 901.0 mm x 423.0 mm
(53.4 inch x 35.4 inch x 16.6 inch)
Without stand
1173.4 mm x 723.4 mm x 100.8 mm
(46.1 inch x 28.4 inch x 3.9 inch)
1357.0 mm x 835.4 mm x 109.6 mm
(53.4 inch x 32.8 inch x 4.3 inch)
Weight
With stand
23.6 kg (52.0 lbs)
36.4 kg (80.2 lbs)
Without stand
20.8 kg (45.8 lbs)
32.9 kg (72.5 lbs)
2.5 A
42LD630 (42LD630-UC)
3.4 A
47LD630 (47LD630-UC)
1024.0 mm x 685.0 mm x 261.0 mm
(40.3 inch x 26.9 inch x 10.2 inch)
1137.0 mm x 758.0 mm x 270.0 mm
(44.7 inch x 29.8 inch x 10.6 inch)
1024.0 mm x 621.0 mm x 76.8 mm
(40.3 inch x 24.4 inch x 3.0 inch)
1137.0 mm x 685.0 mm x 76.8 mm
(44.7 inch x 26.9 inch x 3.0 inch)
With stand
15.5 kg (34.1 lbs)
20.3 kg (44.7 lbs)
Without stand
13.9 kg (30.6 lbs)
18.3 kg (40.3 lbs)
2.1 A
2.5 A
Current Value
MODELS
Dimensions
(Width x
Height
x Depth)
With stand
Without stand
Weight
Current Value
MODELS
APPENDIX
Dimensions
(Width x
Height
x Depth)
With stand
Without stand
Weight
55LD630 (55LD630-UC)
1329.0 mm x 872.0 mm x 330.0 mm
(52.3 inch x 34.3 inch x 12.9 inch)
1329.0 mm x 796.0 mm x 96.5 mm
(52.3 inch x 31.3 inch x 3.7 inch)
With stand
33.0 kg (72.7 lbs)
Without stand
29.8 kg (65.6 lbs)
Current Value
3.4 A
Power requirement
AC 100-240 V ~ 50 / 60 Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
Environment
condition
Operating Temperature
ꔛ The
75 Ω
0 °C to 40 °C (32 °F to 104 °F)
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C (-4 °F to 140 °F)
Storage Humidity
150
32LD520 (32LD520-UA)
Less than 85 %
specifications shown above may be changed without prior notice for quality improvement.
IR CODE
Code Function
Note
Function
Note
00
CH ꕌ
Remote Control Button
0C
POTAL
Remote Control Button
01
CH ꕍ
Remote Control Button
AB
GUIDE
Remote Control Button
02
VOL +
Remote Control Button
B0
03
VOL -
Remote Control Button
B1
06
>
Remote Control Button
BA
ꕖ
ꕗ
ꕘ
07
<
Remote Control Button
D6
TV
(Hexa)
Code
(Hexa)
Remote Control Button
08
(Power On/Off)
MUTE
Remote Control Button
0B
INPUT
Remote Control Button
0F
TV
Remote Control Button
10-19
Number 0-9
Remote Control Button
1A
FLASHBK
Remote Control Button
1E
FAV/MARK
Remote Control Button
28
BACK or RETURN Remote Control Button
30
AV MODE
Remote Control Button
40
ꕌ
Remote Control Button
41
ꕍ
Remote Control Button
43
MENU
Remote Control Button
44
ENTER
Remote Control Button
45
Q.MENU
Remote Control Button
4C
- (Dash)/LIST
Remote Control Button
5B
EXIT
Remote Control Button
79
RATIO
Remote Control Button
7E
SIMPLINK
Remote Control Button
8F
ꕙ
ꕚ
95
ENERGY SAVING Remote Control Button
AA
INFO
Remote Control Button
61 C3
BLUE
Remote Control Button
63 C2
YELLOW
Remote Control Button
71 C0
GREEN
Remote Control Button
72 C1
RED
Remote Control Button
8E
Remote Control Button
Remote Control Button
Remote Control Button
Discrete IR Code
(TV Input Selection)
C4
POWER ON
Discrete IR Code
(Only Power On)
C5
POWER OFF
Discrete IR Code
(Only Power Off)
5A
AV or AV1
D0
AV2
Discrete IR Code
(AV1 Input Selection)
Discrete IR Code
(AV2 Input Selection)
BF
COMPONENT
Discrete IR Code
(Component Input Selection)
D5
RGB-PC
Discrete IR Code
(RGB-PC Input Selection)
CE
HDMI1
CC
HDMI2
Discrete IR Code
(HDMI1 Input Selection)
Discrete IR Code
(HDMI2 Input Selection)
E9
HDMI3
Discrete IR Code
(HDMI3 Input Selection)
DA
HDMI4
76
Ratio 4:3
Remote Control Button
Discrete IR Code
APPENDIX
09
Remote Control Button
(HDMI4 Input Selection)
Discrete IR Code
(Only 4:3 Mode)
77
Ratio 16:9
AF
Ratio Zoom
Discrete IR Code
(Only 16:9 Mode)
Discrete IR Code
(Only Zoom Mode)
For 32/37/42/47LD452C, 32/42/47LD452B
ꔛ Use
this feature depending on your models.
151
APPENDIX
EXTERNAL CONTROL THROUGH RS-232C
The RS-232C port allows you connect the RS-232C input jack to an external control device (such as
a computer or an A/V control system) to control the TV’s functions externally.
ꔛ Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and
software.
The instructions below are provided to help with programming software or to test functionality using
telenet software.
RS-232C Setup
DC-IN
/DVI IN
i.e)
1
(DVI)
2
RS-232C IN
(CONTROL&SERVICE)
OPTICAL
AUDIO IN DIGITAL
RGB/DVI AUDIO OUT
AV IN
VIDEO L(MONO) AUDIO R
RGB IN (PC)
Y
PB
VIDEO
PR
L
AUDIO
COMPONENT IN
R
ANTENNA/
CABLE IN
Communication Parameters
Type of Connector; D-Sub 9-Pin Male
No.
APPENDIX
152
1
2
3
4
5
6
7
8
9
PC
Baud rate : 9600 bps (UART)
ꔛ Data
length : 8 bits
ꔛ Parity
: None
ꔛ Stop
bit : 1 bit
ꔛ Communication
code : ASCII code
ꔛ Use
a crossed (reverse) cable.
Pin Name
ꔛ
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
!
No Connection
1
5
6
9
?
! NOTE
►This product has command echo back in
the RS-232C Command.
?
RS-232C Configurations
7-Wire Configuration
(Serial female-female NULL modem cable)
PC
TV
RXD TXD
GND
DTR
DSR
RTS
CTS
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations
(Not standard)
PC
TV
RXD TXD
GND
DTR
DSR
RTS
CTS
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
Use this function to specify a TV ID number.
Refer to ‘Real Data Mapping’.
OPTION
ꔂ Move
ꔉ Enter
• Language
• Caption
OPTION
ꔂ Move
ꔉ Enter
• Language
: Off
• Caption
• Power Indicator
: Off
• Power Indicator
• Initial Setting
• Initial Setting
• Set ID
:1
• Mode Setting
: Home Use
ꔉ
ꔀ
◀
• Set ID
:1
• Mode Setting
: Home Use
1
▶
Close
2
3
Select OPTION.
MENU
Select Set ID.
ENTER
Choose the desired TV ID number.
The adjustment range of Set ID is
1~ 99.
ENTER
4
RETURN
EXIT
or
BACK
Return to the previous menu.
Return to TV viewing.
Real data mapping
ꔛ
0
Step 0
A
Step 10 (Set ID 10)
F
Step 15 (Set ID 15)
10
Step 16 (Set ID 16)
63
Step 99 (Set ID 99)
64
Step 100
APPENDIX
1
153
APPENDIX
Command Reference List
COMMAND2
DATA
(Hexadecimal)
01. Power
k
a
00 - 01
02. Input Select
x
b
► P.155
03. Aspect Ratio
k
c
► P.155
04. Screen Mute
k
d
00 - 01
05. Volume Mute
k
e
00 - 01
06. Volume
Control
k
f
00 - 64
07. Contrast
k
g
00 - 64
08. Brightness
k
h
00 - 64
09. Color
k
i
00 - 64
10. Tint
k
j
00 - 64
11. Sharpness
k
k
00 - 64
12. OSD Select
k
l
00 - 01
13. R
emote
Control Lock
Mode
k
m
00 - 01
14. Treble
k
r
00 - 64
15. Bass
k
s
00 - 64
APPENDIX
16. Balance
k
t
00 - 64
17. C
olor
Temperature
x
u
00 - 64
18. Energy Saving j
q
► P.156
19. A
uto
Configuration
j
u
► P.156
21. C
hannel Add/
Del
m
b
00 - 01
22. Key
m
c
► P.157
23. Backlight
m
g
00 - 64
20.
Channel
Tuning
154
Transmission / Receiving Protocol
COMMAND1
COMMAND1
COMMAND2
DATA00
(Hexadecimal)
DATA01
(Hexadecimal)
m
a
physical
program
high
major
program
low
DATA02
(Hexadecimal)
DATA03
(Hexadecimal)
DATA04
(Hexadecimal)
DATA05
(Hexadecimal)
major low
minor
high
minor low
attribute
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set. (j,
k, m or x)
[Command 2] : Second command to control the
set.
[Set ID] : You can adjust the set ID to choose
desired TV ID number in Setup menu.
Adjustment range is 1-99. When selecting
Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal
(1-99) on menu and as Hexa decimal (0x0
- 0x63) on transmission /receiving protocol.
[DATA] : To transmit the command data.
Transmit the ‘FF’ data to read status of
command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
* In this model, TV will not send the status during the
standby mode.
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
The TV transmits ACK (acknowledgement) based
on this format when receiving normal data. At this
time, if the data is data read mode, it indicates present status data. If the data is data write mode, it
returns the data of the PC computer.
* In this model, TV will not send the status during the
standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send
the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will
send the ‘a’, ‘b’.
[OK] : Use the large character.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
he TV transmits ACK (acknowledgement) based
T
on this format when receiving abnormal data from
non-viable functions or communication errors.
Data1: Illegal Code
Data2: Not supported function
Data3: Wait more time
* In this model, TV will not send the status during the
standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send
the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will
send the ‘a’, ‘b’.
[NG] : Use the large character
01.Power (Command: k a)
05. Volume Mute (Command: k e)
To control Power On/Off of the TV.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Data 00: Power Off
To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* In a like manner, if other functions transmit ‘FF’ data
based on this format, Acknowledgement data feedback presents status about each function.
* Note: In this model, TV will send the Acknowledge
after power on processing completion.
There might be a time delay between command and
acknowledge.
Data 01: Power On
02. Input Select (Command: x b)
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00: Volume mute on (Volume off)
Data 01: Volume mute off (Volume on)
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
06. Volume Control (Command: k f)
To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
To select input source for TV.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 00: DTV (Antenna)Data 01: DTV (Cable)
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Data 10: Analog (Antenna) Data 11: Analog (Cable)
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
Data 20: AV or AV1
Data 40: Component or Component1
Data 41: Component2
Data 60: RGB-PC
Data 90: HDMI1
Data 91: HDMI2
Data 92: HDMI3
Data 93: HDMI4
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
Data 21: AV 2
* Use the feature depending on your model.
03. Aspect Ratio (Command: k c)
To adjust the screen format.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01: 4:3
Data 02: 16:9 Data 04: Zoom Data 06: Set by program Data 1F: Cinema Zoom16
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
Data 09: Just scan
Data 10: Cinema Zoom1
To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
08. Brightness (Command: k h)
To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
09. Color (Command: k i)
04. Screen Mute (Command: k d)
To adjust screen color.
You can also adjust color in the PICTURE menu.
To select screen mute on/off.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00: Screen mute off (Picture on), Video-out Mute off
Data 01: Screen mute on (Picture off)
Data 10: Video-out Mute on
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of Video-out Mute on only, TV will display On
Screen Display (OSD). But, in case of screen mute
on, TV will not display On Screen Display (OSD).
APPENDIX
07. Contrast (Command: k g)
10. Tint (Command: k j)
To adjust screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red: 00 - Green: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]
155
APPENDIX
11. Sharpness (Command: k k)
To adjust screen sharpness.
You can also adjust sharpness in the Picture menu.
17. Color Temperature (Command: x u)
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
To adjust color temperature.
You can also adjust color temperature in the Picture
menu.
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
12. OSD Select (Command: k l)
To select OSD (On Screen Display) on/off.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00: OSD off
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
Data 01: OSD on
13. Remote Control Lock Mode (Command: k m)
To lock the remote control and the front panel controls on the set.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00: Lock off
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
Data 01: Lock on
If you’re not using the remote control and front panel
controls on the TV, use this mode. When main power
is on/off, remote control lock is released.
If Key Lock is on in the standby mode, TV will not turn
on by POWER button of remote control and on the
TV.
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
18. Energy Saving (Command: j q)
To control the energy saving function.
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Data 00: Energy saving - off
01: Energy saving - Minimum
02: Energy saving - Medium
03: Energy saving - Maximum
04: Energy saving - Auto (depending on model)
05: Energy saving - Screen off
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
To adjust picture position and minimize image shaking automatically. Auto configuration only works in
RGB-PC mode.
APPENDIX
Transmission [ j ][u][ ][Set ID][ ][Data][Cr]
14. Treble (Command: k r)
Data 01: To set
To adjust treble.
You can also adjust treble in the Audio menu.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][r][ ][Set ID][ ][Data][Cr]
20. Channel Tuning (Command: m a)
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
To tune channel to following physical/major/minor number.
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
15. Bass (Command: k s)
To adjust bass.
You can also adjust bass in the Audio menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
16. Balance (Command: k t)
156
19. Auto Configuration (Command: j u)
To adjust balance.
You can also adjust balance in the Audio menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
the sub-channel. Since the ATSC tuner automatically
maps the channel to the Major number, the Physical
number is not required when sending a command.
Data 00: Physical Channel Number
NTSC air: 02 - 45, NTSC cable: 01, 0E - 7D
ATSC air: 01 - 45, ATSC cable: 01 - 87
Data 01 & 02: Major Channel Number
Data 01: High byte
Data 02: Low byte
T
wo bytes are available for the Major and Minor,
normally only the second byte is used.
Data 03 & 04: Minor Channel Number
Not needed for NTSC.
Data5: 7
4
Reserved
5
Two/One Part
Channel
Using Physical
Channel
0 Main
0 Two
0 Use
x
0
0
0
0
NTSC Air
1 Sub
1 One
1 No Use
x
0
0
0
1
NTSC Cable
x
0
0
1
0
ATSC Air
x
0
0
1
1
ATSC Cable_std
x
0
1
0
0
ATSC Cable_hrc
x
0
1
0
1
ATSC Cable_irc
x
0
1
1
0
ATSC cable_auto
x
0
1
1
1
Reserved
x
x
x
x
x
...
x
1
1
1
1
Reserved
The table above lists the binary code which must be
converted to Hexadecimal before sending. For example: The binary code to tune the sub source to an
NTSC cable channel is “1000 0001”, which translates
to “81” in Hex.
* 7th bit : For which source do you want to change the
channel.
*6
th bit: Use a two part or one part channel. Most
cases just use 0 since it’s ignored when using
NTSC.
*5
th bit: Use 0 with NTSC since it can only use the
physical channel number. Normally use 1 for ATSC
since most times it doesn’t matter what the physical
number is.
* 4th bit: Set to 0.
* 3-0 bits: Choose signal type.
1. Tune to the analog (NTSC) cable channel 35.
Data 00 = Physical of 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = 0000 0001 in binary = 01
Total = ma 00 23 00 00 00 00 01
21. Channel Add/Del (Command: m b)
To add and delete the channels.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00: Channel DeleteData 01: Channel Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
22. Key (Command: m c)
To send IR remote control code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
See page 151.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
When TV is in the standby mode, TV will turn on by
POWER button of remote control only.
23. Backlight (Command: m g)
To adjust screen backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
APPENDIX
*Tune Command Examples:
][Set ID][ Step
][OK][Data00]
3 Acknowledgement[a][
2
1
0
[Data01] [Data02][Data03][Data04][x][a][ ][Set ID][ ]
[NG][Data00][x]
6
Main/Sub
Picture
2. T
une to the digital (ATSC) local channel 30-3.
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = 0010 0010 in binary = 22
Total = ma 00 00 00 1E 00 03 22
157
APPENDIX
OPEN SOURCE LICENSE
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public License is intended to guarantee your freedom to share and change free software - to make sure the
software is free for all its users. This General Public License
applies to most of the Free Software Foundation's software
and to any other program whose authors commit to using
it. (Some other free software foundation software is covered by the GNU Lesser General Public License instead.)
You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed
to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish),
that you receive source code or can get it if you want it, that
you can change the software or use pieces of it in new free
programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the software, or if you modify it.
APPENDIX
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients all
the rights that you have. You must make sure that they, too,
receive or can get the source code. And you must show
them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the
software, and (2) offer you this license which gives you legal
permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to
make certain that everyone understands that there is no
warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients to
know that what they have is not the original, so that any
problems introduced by others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent
this, we have made it clear that any patent must be
158
licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution
and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0. This license applies to any program or other work which
contains a notice placed by the copyright holder saying
it may be distributed under the terms of this General
Public License. The "Program", below, refers to any such
program or work, and a "work based on the Program"
means either the Program or any derivative work under
copyright law: that is to say, a work containing the
Program or a portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in
the term "modification".) Each licensee is addressed as
"you".
Activities other than copying, distribution and modification are not covered by this license; they are outside its
scope. The act of running the Program is not restricted,
and the output from the program is covered only if its
contents constitute a work based on the program (independent of having been made by running the program).
Whether that is true depends on what the program
does.
1. You may copy and distribute verbatim copies of the
program's source code as you receive it, in any medium,
provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that
refer to this license and to the absence of any warranty;
and give any other recipients of the program a copy of
this license along with the Program.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the program or
any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications or
work under the terms of section 1 above, provided that
you also meet all of these conditions:
a) Y
ou must cause the modified files to carry prominent
notices stating that you changed the files and the
date of any change.
b) Y
ou must cause any work that you distribute or publish, that in whole or in part contains or is derived
from the Program or any part there of, to be licensed
as a whole at no charge to all third parties under the
terms of this license.
c) If the modified program normally reads commands
interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that
there is no warranty (or else, saying that you provide
a warranty) and that users may redistribute the program under these conditions, and telling the user
how to view a copy of this license. (Exception: if the
Program itself is interactive but does not normally
print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a
whole. If identifiable sections of that work are not
derived from the Program, and can be reasonably considered independent and separate works in themselves,
then this license, and its terms, do not apply to those
sections when you distribute them as separate works.
But when you distribute the same sections as part of a
whole which is a work based on the Program, the distribution of the whole must be on the terms of this license,
whose permissions for other licensees extend to the
entire whole, and thus to each and every part regardless
of who wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution of derivative or collective works based on the program.
In addition, mere aggregation of another work not
based on the program with the Program (or with a work
based on the program) on a volume of a storage or
distribution medium does not bring the other work
under the scope of this license.
3. You may copy and distribute the program (or a work
based on it, under section 2) in object code or executable form under the terms of sections 1 and 2 above
provided that you also do one of the following:
a) Accompany it with the complete corresponding
machine-readable source code, which must be distributed under the terms of sections 1 and 2 above
on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least
three years, to give any third party, for a charge no
more than your cost of physically performing source
distribution, a complete machine-readable copy of
the corresponding source code, to be distributed
under the terms of sections 1 and 2 above on a
medium customarily used for software interchange;
or,
c) A
ccompany it with the information you received as to
the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program in
object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred form of
the work for making modifications to it. For an executable work, complete source code means all the source
code for all modules it contains, plus any associated
interface definition files, plus the scripts used to control
compilation and installation of the executable. However,
as a special exception, the source code distributed need
not include anything that is normally distributed (in
either source or binary form) with the major components (compiler, kernel, and so on) of the operating
system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by
offering access to copy from a designated place, then
offering equivalent access to copy the source code from
the same place counts as distribution of the source
code, even though third parties are not compelled to
copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the
Program except as expressly provided under this license.
Any attempt otherwise to copy, modify, sublicense or
distribute the Program is void, and will automatically
terminate your rights under this license. However, parties who have received copies, or rights, from you under
this license will not have their licenses terminated so
long as such parties remain in full compliance.
5. You are not required to accept this license, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if
you do not accept this license. Therefore, by modifying
or distributing the program (or any work based on the
program), you indicate your acceptance of this license
to do so, and all its terms and conditions for copying,
distributing or modifying the program or works based
on it.
APPENDIX
6. Each time you redistribute the program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms
and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted
herein. You are not responsible for enforcing compliance
by third parties to this license.
159
APPENDIX
7. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that
contradict the conditions of this license, they do not
excuse you from the conditions of this license. If you
cannot distribute so as to satisfy simultaneously your
obligations under this license and any other pertinent
obligations, then as a consequence you may not distribute the program at all. For example, if a patent license
would not permit royalty-free redistribution of the program by all those who receive copies directly or indirectly through you, then the only way you could satisfy
both it and this license would be to refrain entirely from
distribution of the program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of
the section is intended to apply and the section as a
whole is intended to apply in other circumstances.
APPENDIX
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or to
contest validity of any such claims; this section has the
sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous
contributions to the wide range of software distributed
through that system in reliance on consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software
through any other system and a licensee cannot impose
that choice.
This section is intended to make thoroughly clear what
is believed to be a consequence of the rest of this
license.
8. If the distribution and/or use of the program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who
places the program under this license may add an
explicit geographical distribution limitation excluding
those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case, this
license incorporates the limitation as if written in the
body of this license.
9. The Free Software Foundation may publish revised and/
or new versions of the General Public License from time
to time. Such new versions will be similar in spirit to the
present version, but may differ in detail to address new
problems or concerns.
160
Each version is given a distinguishing version number. If
the program specifies a version number of this license
which applies to it and "any later version", you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation. If the program does not specify a
version number of this license, you may choose any version ever published by the Free Software Foundation.
10.If you wish to incorporate parts of the program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will
be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11.BECAUSE THE PROGRAM IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE
PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE THE PROGRAM
"AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY
AND
FITNESS
FOR
A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE
PROGRAM IS WITH YOU. SHOULD THE PROGRAM
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE
THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE PROGRAM TO
OPERATE WITH ANY OTHER PROGRAMS), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to apply these terms to your new programs
If you develop a new program, and you want it to be of the
greatest possible use to the public, the best way to achieve
this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is
safest to attach them to the start of each source file to
most effectively convey the exclusion of warranty; and each
file should have at least the "copyright" line and a pointer
to where the full notice is found.
one line to give the program's name and a brief idea of
what it does.
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/
or modify it under the terms of the GNU General Public
License as published by the Free Software Foundation;
either version 2 of the license, or (at your option) any later
version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General
Public License along with this program; if not, write to the
Free Software Foundation, Inc., 51 Franklin Street, Fifth
Floor, Boston, MA 02110-1301 USA.
Also add information on how to contact you by electronic
and paper mail.
If the program is interactive, make it output a short notice
like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY;
for details type ‘show w’. This is free software, and you are
welcome to redistribute it under certain conditions; type
‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should
show the appropriate parts of the General Public License.
Of course, the commands you use may be called something other than ‘show w’ and ‘show c’; they could even be
mouse-clicks or menu items-whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the
program ‘Gnomovision’ (which makes passes at compilers)
written by James Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
APPENDIX
This General Public License does not permit incorporating
your program into proprietary programs. If your program is
a subroutine library, you may consider it more useful to
permit linking proprietary applications with the library. If
this is what you want to do, use the GNU Lesser General
Public License instead of this license.
161
APPENDIX
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public
License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
freedom to share and change free software - to make sure
the software is free for all its users.
This license, the Lesser General Public License, applies to
some specially designated software packages - typically
libraries - of the Free Software Foundation and other
authors who decide to use it. You can use it too, but we
suggest you first think carefully about whether this license
or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.
APPENDIX
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for this service
if you wish); that you receive source code or can get it if you
want it; that you can change the software and use pieces
of it in new free programs; and that you are informed that
you can do these things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the library
or if you modify it.
For example, if you distribute copies of the library, whether
gratis or for a fee, you must give the recipients all the rights
that we gave you. You must make sure that they, too,
receive or can get the source code. If you link other code
with the library, you must provide complete object files to
the recipients, so that they can relink them with the library
after making changes to the library and recompiling it. And
you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which
gives you legal permission to copy, distribute and/or modify the library.
162
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the
recipients should know that what they have is not the
original version, so that the original author's reputation will
not be affected by problems that might be introduced by
others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a
company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license obtained
for a version of the library must be consistent with the full
freedom of use specified in this license.
Most GNU software, including some libraries, is covered by
the ordinary GNU General Public License. This license, the
GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain
libraries in order to permit linking those libraries into nonfree programs.
When a program is linked with a library, whether statically
or using a shared library, the combination of the two is
legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore
permits such linking only if the entire combination fits its
criteria of freedom. The Lesser General Public License
permits more lax criteria for linking other code with the
library.
We call this license the "Lesser" General Public License
because it does Less to protect the user's freedom than
the ordinary General Public License. It also provides other
free software developers Less of an advantage over competing non-free programs. These disadvantages are the
reason we use the ordinary General Public License for
many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special
need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve
this, non-free programs must be allowed to use the library.
A more frequent case is that a free library does the same
job as widely used non-free libraries. In this case, there is
little to gain by limiting the free library to free software only,
so we use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use
a large body of free software. For example, permission to
use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a
program that is linked with the Library has the freedom and
the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution
and modification follow. Pay close attention to the difference between a "work based on the library" and a "work
that uses the library". The former contains code derived
from the library, whereas the latter must be combined with
the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0.This license agreement applies to any software library or
other program which contains a notice placed by the
copyright holder or other authorized party saying it may
be distributed under the terms of this Lesser General
Public License (also called “this license”). Each license
is addressed as "you".
A “library” means a collection of software functions
and/or data prepared so as to be conveniently linked
with application programs (which use some of those
functions and data) to form executables.
The “Library”, below, refers to any such software library or
work which has been distributed under these terms. A
“work based on the Library” means either the Library or
any derivative work under copyright law: that is to say, a
work containing the library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is
included without limitation in the term “modification”.)
“Source code” for a work means the preferred form of
the work for making modifications to it. For a library,
complete source code means all the source code for all
modules it contains, plus any associated interface definition files, plus the scripts used to control compilation
and installation of the library.
Activities other than copying, distribution and modification are not covered by this license; they are outside its
scope. The act of running a program using the Library
is not restricted, and output from such a program is
covered only if its contents constitute a work based on
the library (independent of the use of the Library in a
tool for writing it). Whether that is true depends on what
the library does and what the program that uses the
library does.
1. You may copy and distribute verbatim copies of the
library's complete source code as you receive it, in any
medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright
notice and disclaimer of warranty; keep intact all the
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or
any portion of it, thus forming a work based on the
Library, and copy and distribute such modifications or
work under the terms of section 1 above, provided that
you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent
notices stating that you changed the files and the
date of any change.
c) You must cause the whole of the work to be licensed
at no charge to all third parties under the terms of
this license.
d) If a facility in the modified Library refers to a function
or a table of data to be supplied by an application
program that uses the facility, other than as an argument passed when the facility is invoked, then you
must make a good faith effort to ensure that, in the
event an application does not supply such function or
table, the facility still operates, and performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square
roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d
requires that any application-supplied function or table
used by this function must be optional: if the application
does not supply it, the square root function must still
compute square roots.)
These requirements apply to the modified work as a
whole. If identifiable sections of that work are not
derived from the library, and can be reasonably considered independent and separate works in themselves,
then this license, and its terms, do not apply to those
sections when you distribute them as separate works.
But when you distribute the same sections as part of a
whole which is a work based on the library, the distribution of the whole must be on the terms of this license,
whose permissions for other licenses extend to the
entire whole, and thus to each and every part regardless
of who wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution of derivative or collective works based on the library.
APPENDIX
notices that refer to this license and to the absence of
any warranty; and distribute a copy of this license along
with the Library.
In addition, mere aggregation of another work not based
on the library with the library (or with a work based on
the library) on a volume of a storage or distribution
medium does not bring the other work under the scope
of this license.
163
APPENDIX
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a given
copy of the Library. To do this, you must alter all the
notices that refer to this License, so that they refer to the
ordinary GNU General Public License, version 2, instead
of to this License. (If a newer version than version 2 of
the ordinary GNU General Public License has appeared,
then you can specify that version instead if you wish.) Do
not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public
License applies to all subsequent copies and derivative
works made from that copy.
This option is useful when you wish to copy part of the
code of the library into a program that is not a library.
4. You may copy and distribute the library (or a portion or
derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above
provided that you accompany it with the complete corresponding machine-readable source code, which must
be distributed under the terms of sections 1 and 2
above on a medium customarily used for software interchange.
If distribution of object code is made by offering access
to copy from a designated place, then offering equivalent access to copy the source code from the same
place satisfies the requirement to distribute the source
code, even though third parties are not compelled to
copy the source along with the object code.
APPENDIX
5. A program that contains no derivative of any portion of
the Library, but is designed to work with the Library by
being compiled or linked with it, is called a “work that
uses the Library”. Such a work, in isolation, is not a
derivative work of the Library, and therefore falls outside
the scope of this license.
However, linking a “work that uses the library” with the
Library creates an executable that is a derivative of the
Library (because it contains portions of the library),
rather than a “work that uses the library”. The executable
is therefore covered by this license. Section 6 states
terms for distribution of such executable.
When a “work that uses the library” uses material from
a header file that is part of the library, the object code
for the work may be a derivative work of the library even
though the source code is not.
Whether this is true is especially significant if the work
can be linked without the library, or if the work is itself a
library. The threshold for this to be true is not precisely
defined by law.
164
If such an object file uses only numerical parameters,
data structure layouts and accessories, and small macros and small inline functions (ten lines or less in
length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work.
(Executable containing this object code plus portions of
the library will still fall under Section 6.)
Otherwise, if the work is a derivative of the library, you
may distribute the object code for the work under the
terms of Section 6. Any executable containing that work
also fall under Section 6, whether or not they are linked
directly with the library itself.
6. As an exception to the sections above, you may also
combine or link a "work that uses the library" with the
library to produce a work containing portions of the
library, and distribute that work under terms of your
choice, provided that the terms permit modification of
the work for the customer's own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the
work that the library is used in it and that the Library and
its use are covered by this license. You must supply a
copy of this license. If the work during execution displays copyright notices, you must include the copyright
notice for the library among them, as well as a reference
directing the user to the copy of this license. Also, you
must do one of these things:
a) A
ccompany the work with the complete corresponding machine-readable source code for the library
including whatever changes were used in the work
(which must be distributed under Sections 1 and 2
above); and, if the work is an executable linked with
the Library, with the complete machine-readable
“work that uses the Library”, as object code and/or
source code, so that the user can modify the library
and then relink to produce a modified executable
containing the modified library. (It is understood that
the user who changes the contents of definitions files
in the library will not necessarily be able to recompile
the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking
with the library. A suitable mechanism is one that (1)
uses at run time a copy of the library already present
on the user’s computer system, rather than copying
library functions into the executable, and (2) will operate properly with a modified version of the library, if the
user installs one, as long as the modified version is
interface-compatible with the version that the work
was made with.
c) Accompany the work with a written offer, valid for at
least three years, to give the same user the materials
specified in Subsection 6, above, for a charge no
more than the cost of performing this distribution.
d) If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specified materials from
the same place.
e) Verify that the user has already received a copy of
these materials or that you have already sent this user
a copy.
For an executable, the required form of the "work that
uses the library" must include any data and utility programs needed for reproducing the executable from it.
However, as a special exception, the materials to be
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that do
not normally accompany the operating system. Such a
contradiction means you cannot use both them and the
library together in an executable that you distribute.
7. You may place library facilities that are a work based on
the library side-by-side in a single library together with
other library facilities not covered by this license, and
distribute such a combined library, provided that the
separate distribution of the work based on the Library
and of the other library facilities is otherwise permitted,
and provided that you do these two things:
a) A
ccompany the combined library with a copy of the
same work based on the Library, uncombined with
any other library facilities. This must be distributed
under the terms of the sections above.
b) Give prominent notice with the combined library of
the fact that part of it is a work based on the library,
and explaining where to find the accompanying
uncombined form of the same work.
9. You are not required to accept this license, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the library or its
derivative works. These actions are prohibited by law if
you do not accept this license. Therefore, by modifying
or distributing the library (or any work based on the
library), you indicate your acceptance of this license to do
so, and all its terms and conditions for copying, distributing or modifying the library or works based on it.
10.Each time you redistribute the library (or any work based
on the Library), the recipient automatically receives a
license from the original licensor to copy, distribute, link
with or modify the library subject to these terms and
conditions. You may not impose any further restrictions
on the recipients' exercise of the rights granted herein.
You are not responsible for enforcing compliance by
third parties with this license.
11.If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that
contradict the conditions of this license, they do not
excuse you from the conditions of this license. If you
cannot distribute so as to satisfy simultaneously your
obligations under this license and any other pertinent
obligations, then as a consequence you may not distribute the library at all. For example, if a patent license
would not permit royalty-free redistribution of the library
by all those who receive copies directly or indirectly
through you, then the only way you could satisfy both it
and this license would be to refrain entirely from distribution of the library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of
the section is intended to apply, and the section as a
whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or to
contest validity of any such claims; this section has the
sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous
contributions to the wide range of software distributed
through that system in reliance on consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software
through any other system and a license cannot impose
that choice.
This section is intended to make thoroughly clear what
is believed to be a consequence of the rest of this
license.
12.If the distribution and/or use of the library is restricted in
certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the
library under this license may add an explicit geographical distribution limitation excluding those countries, so
that distribution is permitted only in or among countries
not thus excluded. In such case, this license incorporates
the limitation as if written in the body of this license.
APPENDIX
8. You may not copy, modify, sublicense, link with, or distribute the library except as expressly provided under
this license. Any attempt otherwise to copy, modify,
sublicense, link with, or distribute the library is void, and
will automatically terminate your rights under this
license. However, parties who have received copies, or
rights, from you under this license will not have their
licenses terminated so long as such parties remain in
full compliance.
13.The Free Software Foundation may publish revised and/
or new versions of the Lesser General Public License
from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number. If
the library specifies a version number of this license
which applies to it and “any later version”, you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation.
165
APPENDIX
If the library does not specify a license version number,
you may choose any version ever published by the Free
Software Foundation.
14.If you wish to incorporate parts of the library into other
free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free
Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software
and of promoting the sharing and reuse of software
generally.
NO WARRANTY
15.BECAUSE THE LIBRARY IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE
LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE
LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. THE ENTIRE RISK
AS TO THE QUALITY AND PERFORMANCE OF THE
LIBRARY IS WITH YOU. SHOULD THE LIBRARY
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
APPENDIX
16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE
THE LIBRARY (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE LIBRARY TO
OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to apply these terms to your new libraries
If you develop a new library, and you want it to be of the
greatest possible use to the public, we recommend making
166
it free software that everyone can redistribute and change.
You can do so by permitting redistribution under these
terms (or, alternatively, under the terms of the ordinary
General Public License).
To apply these terms, attach the following notices to the
library. It is safest to attach them to the start of each
source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line
and a pointer to where the full notice is found.
one line to give the library's name and a brief idea of what
it does.
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General
Public License as published by the Free Software
Foundation; either version 2.1 of the license, or (at your
option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU Lesser General
Public License for more details.
You should have received a copy of the GNU Lesser
General Public License along with this library; if not, write to
the Free Software Foundation, Inc., 51 Franklin Street, Fifth
Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic
and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter
the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the
library ‘Frob’ (a library for tweaking knobs) written by James
Random Hacker.
signature of Ty Coon, 1 April 1990
Ty Coon, President of Vice
MOZILLA PUBLIC LICENSE
Version 1.1
--------------which, at the time of its release under this license is
not already covered code governed by this license.
1.Definitions.
1.0.1. “Commercial use” means distribution or otherwise
making the covered code available to a third party.
1.1.
“Contributor” means each entity that creates or contributes to the creation of modifications.
1.2. “Contributor version” means the combination of the
original code, prior modifications used by a contributor, and the modifications made by that particular
contributor.
1.3. “Covered code” means the original code or modifications or the combination of the original code and
modifications, in each case including portions thereof.
1.4. “Electronic distribution mechanism” means a mechanism generally accepted in the software development community for the electronic transfer of data.
1.5. “Executable” means covered code in any form other
than source code.
1.6. “Initial developer” means the individual or entity
identified as the initial Developer in the Source Code
notice required by exhibit A.
1.7.
1.11. “Source code” means the preferred form of the covered code for making modifications to it, including all
modules it contains, plus any associated interface
definition files, scripts used to control compilation
and installation of an executable, or source code differential comparisons against either the original code
or another well known, available covered code of the
contributor's choice. The source code can be in a
compressed or archival form, provided the appropriate decompression or de-archiving software is widely available for no charge.
1.12. “You” (or “Your”) means an individual or a legal
entity exercising rights under, and complying with all
of the terms of, this license or a future version of this
license issued under section 6.1.
For legal entities, “You” includes any entity which
controls, is controlled by, or is under common control
with You. For purposes of this definition, “control”
means (a) the power, direct or indirect, to cause the
direction or management of such entity, whether by
contract or otherwise, or (b) ownership of more than
fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
1.8. “License” means this document.
2. Source Code License.
1.8.1. “Licensable” means having the right to grant, to the
maximum extent possible, whether at the time of the
initial grant or subsequently acquired, any and all of
the rights conveyed herein.
2.1. The initial developer grant.
The initial developer hereby grants You a world-wide,
royalty-free, non-exclusive license, subject to third
party intellectual property claims:
1.9.
“Modifications” means any addition to or deletion
from the substance or structure of either the original
code or any previous modifications. When covered
code is released as a series of files, a modification is:
A. Any addition to or deletion from the contents of a
file containing original code or previous modifications.
B. Any new file that contains any part of the original
code or previous modifications.
APPENDIX
“Larger work” means a work which combines covered
code or portions thereof with code not governed by
the terms of this License.
1.10.1. “Patent claims” means any patent claim(s), now
owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any
patent licensable by grantor.
a) u
nder intellectual property rights (other than patent or trademark) licensable by initial developer to
use, reproduce, modify, display, perform, sublicense and distribute the original code (or portions
thereof) with or without modifications, and/or as
part of a larger work; and
(b) under patents claims infringed by the making,
using or selling of original code, to make, have
made, use, practice, sell, and offer for sale, and/
or otherwise dispose of the original code (or portions there of).
1.10. “Original code” means source code of computer
software code which is described in the source code
notice required by exhibit as original code, and
167
APPENDIX
(c) the licenses granted in this section 2.1(a) and (b)
are effective on the date Initial developer first
distributes original code under the terms of this
license.
(d) Notwithstanding section 2.1(b) above, no patent
license is granted: 1) for code that You delete
from the original Code; 2) separate from the
original code; or 3) for infringements caused by:
i) the modification of the original code or ii) the
combination of the original code with other software or devices.
2.2. Contributor Grant.
Subject to third party intellectual property claims,
each contributor hereby grants You a world-wide,
royalty-free, non-exclusive license
APPENDIX
(a) u
nder intellectual property rights (other than patent or trademark) licensable by contributor, to
use, reproduce, modify, display, perform, sublicense and distribute the modifications created by
such contributor (or portions thereof) either on
an unmodified basis, with other modifications, as
covered code and/or as part of a larger work; and
(b) under patent claims infringed by the making,
using, or selling of modifications made by that
contributor either alone and/or in combination
with its contributor version (or portions of such
combination), to make, use, sell, offer for sale,
have made, and/or otherwise dispose of: 1) modifications made by that contributor (or portions
thereof); and 2) the combination of modifications
made by that contributor with its contributor version (or portions of such combination).
(c) the licenses granted in sections 2.2(a) and 2.2(b)
are effective on the date contributor first makes
commercial use of the covered code.
(d) Notwithstanding section 2.2(b) above, no patent
license is granted: 1) for any code that contributor
has deleted from the contributor version; 2)
separate from the contributor version; 3) for
infringements caused by: i) third party modifications of contributor version or ii) the combination
of modifications made by that contributor with
other software (except as part of the contributor
version) or other devices; or 4) under patent
claims infringed by covered code in the absence
of modifications made by that contributor.
3. Distribution Obligations.
3.1. Application of license.
The modifications which You create or to which you
contribute are governed by the terms of this license,
including without limitation section 2.2. The source
code version of covered code may be distributed
only under the terms of this license or a future version of this license released under section 6.1, and
you must include a copy of this license with every
copy of the source code you distribute. You may not
168
offer or impose any terms on any source code version that alters or restricts the applicable version of
this license or the recipients' rights hereunder.
However, you may include an additional document
offering the additional rights described in section
3.5.
3.2. Availability of source code.
Any modification which you create or to which you
contribute must be made available in source code
form under the terms of this license either on the
same media as an executable version or via an
accepted electronic distribution mechanism to anyone to whom you made an executable version available; and if made available via electronic distribution
mechanism, must remain available for at least twelve
(12) months after the date it initially became available, or at least six (6) months after a subsequent
version of that particular modification has been
made available to such recipients. You are responsible for ensuring that the source code version remains
available even if the electronic distribution mechanism is maintained by a third party.
3.3. Description of modifications.
You must cause all covered code to which you contribute to contain a file documenting the changes You
made to create that covered code and the date of any
change. You must include a prominent statement that
the modification is derived, directly or indirectly, from
original code provided by the initial developer and
including the name of the initial developer in (a) the
source code, and (b) in any notice in an executable
version or related documentation in which you describe
the origin or ownership of the covered code.
3.4. Intellectual property matters
(a) Third party claims.
If contributor has knowledge that a license under a
third party's intellectual property rights is required to
exercise the rights granted by such contributor under
sections 2.1 or 2.2, contributor must include a text file
with the source code distribution titled "LEGAL"
which describes the claim and the party making the
claim in sufficient detail that a recipient will know
whom to contact. If contributor obtains such knowledge after the modification is made available as
described in section 3.2, contributor shall promptly
modify the LEGAL file in all copies contributor makes
available thereafter and shall take other steps (such
as notifying appropriate mailing lists or newsgroups)
reasonably calculated to inform those who received
the covered code that new knowledge has been
obtained.
(b) Contributor APIs.
If contributor's modifications include an application
programming interface and contributor has knowledge of patent licenses which are reasonably necessary to implement that API, contributor must also
include this information in the LEGAL file.
(c) Representations.
contributor represents that, except as disclosed pursuant to section 3.4(a) above, contributor believes that
contributor's modifications are contributor's original
creation(s) and/or contributor has sufficient rights to
grant the rights conveyed by this license.
3.5. Required notices.
You must duplicate the notice in exhibit A in each file
of the source code. If it is not possible to put such
notice in a particular source code file due to its structure, then You must include such notice in a location
(such as a relevant directory) where a user would be
likely to look for such a notice. If You created one or
more modification(s), you may add your name as a
contributor to the notice described in exhibit A. you
must also duplicate this license in any documentation for the source code where You describe recipients' rights or ownership rights relating to covered
code. You may choose to offer, and to charge a fee
for, warranty, support, indemnity or liability obligations to one or more recipients of covered code.
However, you may do so only on your own behalf, and
not on behalf of the Initial developer or any contributor. You must make it absolutely clear than any such
warranty, support, indemnity or liability obligation is
offered by you alone, and You hereby agree to
indemnify the Initial developer and every contributor
for any liability incurred by the Initial developer or
such contributor as a result of warranty, support,
indemnity or liability terms you offer.
3.7. Larger works.
You may create a larger work by combining covered
4. Inability to comply due to statute or regulation.
If it is impossible for you to comply with any of the
terms of this license with respect to some or all of
the covered code due to statute, judicial order, or
regulation then you must: (a) comply with the terms
of this license to the maximum extent possible; and
(b) describe the limitations and the code they affect.
Such description must be included in the LEGAL file
described in section 3.4 and must be included with
all distributions of the source code. Except to the
extent prohibited by statute or regulation, such
description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it.
5. Application of this license.
This license applies to code to which the initial developer has attached the notice in exhibit A and to
related covered code.
6. Versions of the license.
6.1. New versions.
Netscape communications corporation (“Netscape”)
may publish revised and/or new versions of the
license from time to time. Each version will be given
a distinguishing version number.
6.2. Effect of new versions.
Once covered code has been published under a
particular version of the license, you may always continue to use it under the terms of that version. You
may also choose to use such covered code under
the terms of any subsequent version of the license
published by netscape. No one other than netscape
has the right to modify the terms applicable to covered code created under this license.
APPENDIX
3.6. Distribution of executable versions.
You may distribute covered code in executable form
only if the requirements of section 3.1-3.5 have been
met for that covered code, and if you include a notice
stating that the source code version of the covered
code is available under the terms of this license,
including a description of how and where you have
fulfilled the obligations of section 3.2. The notice
must be conspicuously included in any notice in an
executable version, related documentation or collateral in which you describe recipients' rights relating
to the covered code. You may distribute the executable version of covered code or ownership rights
under a license of your choice, which may contain
terms different from this license, provided that you
are in compliance with the terms of this license and
that the license for the executable version does not
attempt to limit or alter the recipient's rights in the
source code version from the rights set forth in this
license. If you distribute the executable version under
a different license you must make it absolutely clear
that any terms which differ from this license are
offered by you alone, not by the Initial developer or
any contributor. You hereby agree to indemnify the
initial developer and every contributor for any liability
incurred by the initial developer or such contributor
as a result of any such terms You offer.
code with other code not governed by the terms of
this license and distribute the larger work as a single
product. In such a case, you must make sure the
requirements of this license are fulfilled for the covered code.
6.3. Derivative works.
If You create or use a modified version of this license
(which you may only do in order to apply it to code
which is not already covered code governed by this
license), You must (a) rename Your license so that the
phrases "Mozilla", "MOZILLAPL", "MOZPL",
"Netscape", "MPL", "NPL" or any confusingly similar
phrase do not appear in your license (except to note
that your license differs from this license) and (b)
otherwise make it clear that Your version of the
license contains terms which differ from the Mozilla
Public license and netscape Public License. (Filling in
the name of the initial developer, original code or
contributor in the notice described in exhibit A shall
not of themselves be deemed to be modifications of
this license.)
169
APPENDIX
7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS
LICENSE ON AN “AS IS” BASIS, WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED
OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
WARRANTIES THAT THE COVERED CODE IS FREE
OF DEFECTS, MERCHANTABLE, FIT FOR A
PARTICULAR PURPOSE OR NON-INFRINGING.
THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE COVERED CODE IS WITH
YOU. SHOULD ANY COVERED CODE PROVE
DEFECTIVE IN ANY RESPECT, YOU (NOT THE
INITIAL
DEVELOPER
OR
ANY
OTHER
CONTRIBUTOR) ASSUME THE COST OF ANY
NECESSARY SERVICING, REPAIR OR CORRECTION.
THIS DISCLAIMER OF WARRANTY CONSTITUTES
AN ESSENTIAL PART OF THIS LICENSE. NO USE
OF ANY COVERED CODE IS AUTHORIZED
HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
8. TERMINATION.
8.1. This license and the rights granted hereunder will
terminate automatically if you fail to comply with
terms herein and fail to cure such breach within 30
days of becoming aware of the breach. All sublicenses to the covered code which are properly
granted shall survive any termination of this license.
Provisions which, by their nature, must remain in
effect beyond the termination of this license shall
survive.
APPENDIX
8.2. If you initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions)
against initial developer or a contributor (the initial
developer or contributor against whom you file such
action is referred to as “Participant”) alleging that:
170
(a) s uch participant's contributor version directly or
indirectly infringes any patent, then any and all
rights granted by such participant to you under
sections 2.1 and/or 2.2 of this license shall, upon
60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of
notice you either: (i) agree in writing to pay participant a mutually agreeable reasonable royalty for
your past and future use of modifications made
by such participant, or (ii) withdraw your litigation
claim with respect to the contributor version
against such participant. If within 60 days of notice,
a reasonable royalty and payment arrangement
are not mutually agreed upon in writing by the
parties or the litigation claim is not withdrawn, the
rights granted by participant to you under sections 2.1 and/or 2.2 automatically terminate at the
expiration of the 60 day notice period specified
above.
(b) any software, hardware, or device, other than such
participant's contributor Version, directly or indirectly infringes any patent, then any rights grant-
ed to You by such participant under sections
2.1(b) and 2.2(b) are revoked effective as of the
date you first made, used, sold, distributed, or
had made, modifications made by that participant.
8.3. If you assert a patent infringement claim against
participant alleging that such participant's contributor version directly or indirectly infringes any patent
where such claim is resolved (such as by license or
settlement) prior to the initiation of patent infringement litigation, then the reasonable value of the
licenses granted by such participant under sections
2.1 or 2.2 shall be taken into account in determining
the amount or value of any payment or license.
8.4. In the event of termination under sections 8.1 or 8.2
above, all end user license agreements (excluding distributors and resellers) which have been validly
granted by you or any distributor hereunder prior to
termination shall survive termination.
9. LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO
LEGAL THEORY, WHETHER TORT (INCLUDING
NEGLIGENCE), CONTRACT, OR OTHERWISE,
SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER
CONTRIBUTOR, OR ANY DISTRIBUTOR OF
COVERED CODE,OR ANY SUPPLIER OF ANY OF
SUCH PARTIES, BE LIABLE TO ANY PERSON FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY CHARACTER
INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF GOODWILL, WORK STOPPAGE,
COMPUTER FAILURE OR MALFUNCTION, OR ANY
AND ALL OTHER COMMERCIAL DAMAGES OR
LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN
INFORMED OF THE POSSIBILITY OF SUCH
DAMAGES. THIS LIMITATION OF LIABILITY SHALL
NOT APPLY TO LIABILITY FOR DEATH OR
PERSONAL INJURY RESULTING FROM SUCH
PARTY'S NEGLIGENCE TO THE EXTENT
APPLICABLE LAW PROHIBITS SUCH LIMITATION.
SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION
AND LIMITATION MAY NOT APPLY TO YOU.
10. U.S. GOVERNMENT END USERS.
The covered code is a "commercial item," as that
term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such
terms are used in 48 C.F.R. 12.212 (Sept. 1995).
Consistent with 48 C.F.R. 12.212 and 48 C.F.R.
227.7202-1 through 227.7202-4 (June 1995), all
U.S. Government end users acquire covered code
with only those rights set forth herein.
11. MISCELLANEOUS.
This license represents the complete agreement concerning subject matter hereof. If any provision of this
license is held to be unenforceable, such provision
shall be reformed only to the extent necessary to
make it enforceable. This License shall be governed
by California law provisions (except to the extent
applicable law, if any, provides otherwise), excluding
its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an
entity chartered or registered to do business in the
united states of america, any litigation relating to this
License shall be subject to the jurisdiction of the
federal courts of the northern district of california,
with venue lying in santa clara county, california, with
the losing party responsible for costs, including without limitation, court costs and reasonable attorneys'
fees and expenses. The application of the united
nations convention on contracts for the International
sale of goods is expressly excluded. Any law or regulation which provides that the language of a contract
shall be construed against the drafter shall not apply
to this license.
12. RESPONSIBILITY FOR CLAIMS.
As between initial developer and the contributors,
each party is responsible for claims and damages
arising, directly or indirectly, out of its utilization of
rights under this license and you agree to work with
initial developer and contributors to distribute such
responsibility on an equitable basis. Nothing herein is
intended or shall be deemed to constitute any
admission of liability.
The contents of this file are subject to the Mozilla Public
License Version 1.1 (the “license”); you may not use this file
except in compliance with the License. You may obtain a
copy of the license at http://www.mozilla.org/MPL/
Software distributed under the license is distributed on an
"AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either
express or implied. See the license for the specific language governing rights and limitations under the License.
The Original Code is ______________________________________
.
The Initial Developer of the Original Code
is___________________.
Portions created by ______________________ are Copyright
(C) _______________________. All Rights Reserved.
Contributor(s): ______________________________________.
Alternatively, the contents of this file may be used under
the terms of the _____ license (the "[___] License"), in
which case the provisions of [______] license are applicable
instead of those above. If you wish to allow use of your
version of this file only under the terms of the [____] license
and not to allow others to use your version of this file under
the MPL, indicate your decision by deleting the provisions
above and replace them with the notice and other provisions required by the [___] license. If you do not delete the
provisions above, a recipient may use your version of this file
under either the MPL or the [___] license."
NOTE: The text of this exhibit A may differ slightly from the
text of the notices in the source code files of the original
code. You should use the text of this exhibit A rather than
the text found in the original code/source code for Your
modifications.
APPENDIX
13. MULTIPLE-LICENSED CODE.
Initial developer may designate portions of the covered code as "Multiple-Licensed". "MultipleLicensed" means that the initial developer permits
you to utilize portions of the covered code under your
choice of the NPL or the alternative licenses, if any,
specified by the initial developer in the file described
in exhibit A.
EXHIBIT A -Mozilla Public License.
171
OWNER’S MANUAL
LED LCD TV / LCD TV
Please read this manual carefully before operating
your set and retain it for future reference.
The model and serial number of the TV is located
on the back and/or one side of the TV.
Record it below should you ever need service.
LED LCD TV MODELS
19LE5300
32LE5300
22LE5300
37LE5300
26LE5300
42LE5300
22LE5500
47LE5300
26LE5500
55LE5300
42LE7300
47LE7300
55LE7300
42LE530C
47LE530C
55LE530C
LCD TV MODELS
32LD420
32LD520
42LD420
42LD520
47LD420
47LD520
32LD450
55LD520
37LD450
42LD630
42LD450
47LD630
47LD450
55LD630
37LD450C
42LD450C
47LD450C
55LD520C
42LD451C
47LD451C
26LD352C
32LD452C
37LD452C
42LD452C
47LD452C
32LD452B
42LD452B
47LD452B
MODEL
SERIAL
P/NO : SAC34134204 (1106-REV14)
www.lg.com
Download PDF

advertising