LG | 47LY340C | LG 47LY340C Owner’s Manual

OWNER’S MANUAL
LED TV*
*LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your TV
and retain it for future reference.
32LY340C
42LY340C
47LY340C
55LY340C
2
Safety Instructions
Safety Instructions
Please read these safety precautions carefully before using the product.
WARNING
Bend antenna cable between inside
yy
and outside building to prevent rain
from flowing in. This may cause
water damaged inside the Product
and could give an electric shock.
ENGLISH
Do not place the TV and/or
yy
remote control in the following
environments:
- A location exposed to direct sunlight
- An area with high humidity such as
a bathroom
- Near any heat source such as
stoves and other devices that
produce heat
- Near kitchen counters or humidifiers
where they can easily be exposed
to steam or oil
- An area exposed to rain or wind
- Near containers of water such as
vases
Otherwise, this may result in fire,
electric shock, malfunction or
product deformation.
Do not place the product where it
yy
might be exposed to dust. This may
cause a fire hazard.
Mains Plug is the TV connecting/
yy
disconnecting device to AC mains
electric supply. This plug must
remain readily attached and operable
when TV is in use.
Do not touch the power plug with
yy
wet hands. Additionally, if the cord
pin is wet or covered with dust, dry
the power plug completely or wipe
dust off. You may be electrocuted
due to excess moisture.
Make sure to connect Mains cable
yy
to compliant AC mains socket with
Grounded earth pin. (Except for
devices which are not grounded on
earth.) Otherwise possibility you may
be electrocuted or injured.
Insert power cable plug completely
yy
into wall socket otherwise if not
secured completely into socket, fire
ignition may break out.
Ensure the power cord does not
yy
come into contact with hot objects
such as a heater. This may cause a
fire or an electric shock hazard.
Do not place a heavy object, or the
yy
product itself, on power cables.
Otherwise, this may result in fire or
electric shock.
When mounting TV onto wall make
yy
sure to neatly install and isolate
cabling from rear of TV as to not
create possibility of electric shock /
fire hazard.
Do not plug too many electrical
yy
devices into a single multiple
electrical outlet. Otherwise, this may
result in fire due to over-heating.
Do not drop the product or let it
yy
fall over when connecting external
devices. Otherwise, this may result
in injury or damage to the product.
Desic
can
t
Keep the anti-moisture packing
yy
material or vinyl packing out of the
reach of children. Anti-moisture
material is harmful if swallowed. If
swallowed by mistake, force the
patient to vomit and visit the nearest
hospital. Additionally, vinyl packing
can cause suffocation. Keep it out of
the reach of children.
Do not let your children climb or cling
yy
onto the TV. Otherwise, the TV may
fall over, which may cause serious
injury.
Dispose of used batteries carefully
yy
to ensure that a small child does not
consume them. Please seek DoctorMedical Attention immediately if
child consumes batteries.
Do not insert any metal objects/
yy
conductors (like a metal chopstick/
cutlery/ screwdriver) between power
cable plug and input Wall Socket
while it is connected to the input
terminal on the wall. Additionally, do
not touch the power cable right after
plugging into the wall input terminal.
You may be electrocuted. (Depending
on model)
Do not put or store inflammable
yy
substances near the product. There
is a danger of combustion/explosion
or fire due to careless handling of the
inflammable substances.
Safety Instructions
Do not drop metallic objects such as
yy
coins, hair pins, chopsticks or wire
into the product, or inflammable
objects such as paper and matches.
Children must pay particular
attention. Electrical shock, fire or
injury can occur. If a foreign object is
dropped into the product, unplug the
power cord and contact the service
centre.
Do not spray water on the product or
yy
scrub with an inflammable substance
(thinner or benzene). Fire or electric
shock accident can occur.
Do not allow any impact, shock or
yy
any objects to fall into the unit, and
do not drop anything onto the screen.
You may be injured or the product
can be damaged.
Never touch this product or antenna
yy
during a thunder or lighting storm.
You may be electrocuted.
Do not disassemble, repair or modify
yy
the product at your own discretion.
Fire or electric shock accident can
occur. Contact the service centre for
check, calibration or repair.
If any of the following occur, unplug
yy
the product immediately and contact
your local service centre.
- The product has been impacted by
shock
- The product has been damaged
- Foreign objects have entered the
product
- The product produced smoke or a
strange smell
This may result in fire or electric
shock.
Unplug the TV from AC mains wall
yy
socket if you do not intend to use
the TV for a long period of time.
Accumulated dust can cause fire
hazard and insulation deterioration
can cause electric leakage/shock/fire.
Apparatus shall not be exposed to
yy
dripping or splashing and no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
CAUTION
Install the product where no radio
yy
wave occurs.
There should be enough distance
yy
between an outside antenna and
power lines to keep the former from
touching the latter even when the
antenna falls. This may cause an
electric shock.
Do not install the product on places
yy
such as unstable shelves or inclined
surfaces. Also avoid places where
there is vibration or where the
product cannot be fully supported.
Otherwise, the product may fall or
flip over, which may cause injury or
damage to the product.
If you install the TV on a stand, you
yy
need to take actions to prevent the
product from overturning. Otherwise,
the product may fall over, which may
cause injury.
If you intend to mount the product to a wall, attach
yy
VESA standard mounting interface (optional parts)
to the back of the product. When you install the
set to use the wall mounting bracket (optional
parts), fix it carefully so as not to drop.
Only use the attachments / accessories specified
yy
by the manufacturer.
When installing the antenna, consult
yy
a qualified service man. This may
create a fire hazard or an electric
shock hazard.
We recommend that you maintain a
yy
distance of at least 2 to 7 times the
diagonal screen size when watching
TV. If you watch TV for a long period
of time, this may cause blurred
vision.
Only use the specified type of
yy
battery. This could cause damage to
the remote control.
Do not mix new batteries with
yy
old batteries. This may cause the
batteries to overheat and leak.
Make sure there are no objects
yy
between the remote control and its
sensor.
ENGLISH
Never touch the wall outlet when
yy
there is leakage of gas, open the
windows and ventilate. It may cause
a fire or a burn by a spark.
3
4
Safety Instructions
Signal from Remote Control can be
yy
interrupted due to external/internal
lighting eg Sunlight, fluorescent
lighting. If this occurs turn off lighting
or darken viewing area.
Do not press strongly upon the panel
yy
with a hand or sharp object such as
nail, pencil or pen, or make a scratch
on it, as it may cause damage to
screen.
When connecting external devices
yy
such as video game consoles, make
sure the connecting cables are long
enough. Otherwise, the product may
fall over, which may cause injury or
damage the product.
Avoid touching the screen or
yy
holding your finger(s) against it
for long periods of time. Doing so
may produce some temporary or
permanent distortion/damage to
screen.
Do not turn the product On/Off by
yy
plugging-in or unplugging the power
plug to the wall outlet. (Do not use
the power plug for switch.) It may
cause mechanical failure or could
give an electric shock.
When cleaning the product and its
yy
components, unplug the power
first and wipe it with a soft cloth.
Applying excessive force may cause
scratches or discolouration. Do not
spray with water or wipe with a wet
cloth. Never use glass cleaner, car or
industrial shiner, abrasives or wax,
benzene, alcohol etc., which can
damage the product and its panel.
Otherwise, this may result in fire,
electric shock or product damage
(deformation, corrosion or breakage).
ENGLISH
Please follow the installation
yy
instructions below to prevent the
product from overheating.
- The distance between the product
and the wall should be more than 10
cm.
- Do not install the product in a
place with no ventilation (e.g., on a
bookshelf or in a cupboard).
- Do not install the product on a
carpet or cushion.
- Make sure the air vent is not
blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
Take care not to touch the ventilation
yy
openings when watching the TV
for long periods as the ventilation
openings may become hot. This
does not affect the operation or
performance of the product.
Periodically examine the cord of your appliance,
yy
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized servicer.
Prevent dust collecting on the power
yy
plug pins or outlet. This may cause a
fire hazard.
Protect the power cord from physical
yy
or mechanical abuse, such as being
twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular
attention to plugs, wall outlets, and
the point where the cord exits the
appliance.
As long as this unit is connected to the AC wall
yy
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
When unplugging the cable, grab the
yy
plug and unplug it, by pulling at the
plug. Don’t pull at the cord to unplug
the power cord from the power
board, as this could be hazardous.
When moving the product, make
yy
sure you turn the power off first.
Then, unplug the power cables,
antenna cables and all connecting
cables. The TV set or power cord
may be damaged, which may create
a fire hazard or cause electric shock.
When moving or unpacking the
yy
product, work in pairs because the
product is heavy. Otherwise, this
may result in injury.
Contact the service centre once a
yy
year to clean the internal parts of
the product. Accumulated dust can
cause mechanical failure.
Safety Instructions
Refer all servicing to qualified service
yy
personnel. Servicing is required when
the apparatus has been damaged in
any way, such as power supply cord
or plug is damaged, liquid has been
spilled or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
If the product feels cold to the touch,
yy
there may be a small “flicker” when
it is turned on. This is normal, there
is nothing wrong with product.
You may find different brightness
yy
and colour of the panel depending
on your viewing position(left/right/
top/down). This phenomenon
occurs due to the characteristic of
the panel. It is not related with the
product performance, and it is not
malfunction.
Displaying a still image (e.g., broadcasting channel
yy
logo, on-screen menu, scene from a video game)
for a prolonged time may cause damage to the
screen, resulting in retention of the image, which
is known as image sticking. The warranty does not
cover the product for image sticking.
Avoid displaying a fixed image on your television’s
screen for a prolonged period. Also, if you watch
the TV at a ratio of 4:3 for a long time, image
sticking may occur on the borders of the panel.
This phenomenon also occurs in third-party
products and is not subject to exchange or refund.
Generated Sound
yy
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to tempera-ture
and humidity. This noise is common for products
where thermal deformation is required. Electrical
circuit humming/panel buzzing: A low level
noise is generated from a high-speed switching
circuit, which supplies a large amount of current
to operate a product. It varies depending on the
product. This generated sound does not affect the
performance and reliability of the product.
Do not install this product on a wall if
yy
it could be exposed to oil or oil mist.
This may damage the product and
cause it to fall.
WARNING
If you ignore the warning message, you
may be seriously injured or there is a
possibility of accident or death.
CAUTION
If you ignore the caution message, you
may be slightly injured or the product may
be damaged.
NOTE
The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
ENGLISH
The panel is a high technology display
yy
product with resolution of two million
to six million pixels. You may see tiny
black dots and/or brightly coloured
dots (red, blue or green) at a size of
1 ppm on the panel. This does not
indicate a malfunction and does not
affect the performance and reliability
of the product. This phenomenon
also occurs in third-party products
and is not subject to exchange or
refund.
5
6
LICENSES / OPEN SOURCE SOFTWARE NOTICE
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
ENGLISH
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that has
passed rigorous testing to verify that it plays DivX video. Visit divx.com for more
information and software tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be
registered in order to play purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX VOD section in your device
setup menu. Go to vod.divx.com for more information on how to complete your
registration.
DivX Certified® to play DivX® video up to HD 1080p, including premium content.
DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation
or its subsidiaries and are used under license.
Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in
this product, please visit http://opensource.lge.com. In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
NOTE
yyImage shown may differ from your TV.
yyYour TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yyThe available menus and options may differ from the input source or product model that you are
using.
New features may be added to this TV in the future.
yy
TABLE OF CONTENTS
7
TABLE OF CONTENTS
2
Safety Instructions
19
MAINTENANCE
6
LICENSES
19
19
19
Cleaning your TV
- Screen, Frame, Cabinet, and Stand
- Power Cord
6OPEN SOURCE SOFTWARE
NOTICE
7TABLE OF CONTENTS
8ASSEMBLING AND PREPARING
Unpacking
Parts and Buttons
- Using the Joystick Button
Lifting and Moving the TV
Setting up the TV
- Attaching the Stand
- Mounting on a Table
- Mounting on a Wall
15
MAKING CONNECTIONS
15
16
Connecting to an Antenna or Cable
Other Connections
18REMOTE CONTROL
21
SPECIFICATIONS
23
IR CODES
24
EXTERNAL CONTROL DEVICE
SETUP
24
24
RS-232C Setup
Type of Connector;
D-Sub 9-Pin Male
RS-232C Configurations
Communication Parameters
Command Reference List
Transmission / Receiving Protocol
25
26
26
27
ENGLISH
8
10
11
12
12
12
13
14
20TROUBLESHOOTING
8
ASSEMBLING AND PREPARING
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
ENGLISH
Remote Control,
Batteries (AAA)
(Depending on model)
Owner’s Manual
(For 42/47/55LY340C)
(For 32LY340C)
Stand Screws
4 EA, M4 x L14
Stand Screws
4 EA, M4 x L20
(For 42LY340C)
Wall Mount Spacers
2 EA
Power Cord
Stand Base
Cable Holder
1 EA
Stand Holder
2 EA
9
ASSEMBLING AND PREPARING
CAUTION
yyDo not use any unapproved items to ensure the safety and product’s lifespan.
yyAny damages or injuries by using unapproved items are not covered by the warranty.
yySome models appear to have a thin film on the screen. It is actually part of the screen; do not
remove it.
NOTE
yyThe items supplied with your product may vary depending on the
model.
yyProduct specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
yyFor an optimal connection, HDMI cables and USB devices should A
have bezels less than 10 mm (0.39 inches) thick and 18 mm
(0.7 inches) width.
yyUse an extension cable that supports USB 2.0 if the USB cable or
USB memory stick does not fit into your TV’s USB port.
B
B
A
*A ≤ 10 mm
*B ≤ 18 mm
ENGLISH
10
ASSEMBLING AND PREPARING
Parts and Buttons
Screen
Speakers
Joystick Button1
Remote Control Sensor
Power Indicator
ENGLISH
1. Joystick button is located below the screen of TV.
NOTE
yyYou can set the power indicator light to on or off by selecting OPTION in the main menus.
ASSEMBLING AND PREPARING
11
Using the Joystick Button
You can simply operate the TV functions, pressing or moving the joystick button up, down, left or right
Basic functions
When the TV is turned off, place your finger on the joystick button and
press it once and release it.
Power On
When the TV is turned on, place your finger on the joystick button and
press it once for a few seconds and release it.
Power Off
(However, if the Menu button is on the screen, pressing and holding the
joystick button will let you exit the Menu.)
Volume Control
If you place your finger over the joystick button and move it left or right,
you can adjust the volume level you want.
Channels Control
If you place your finger over the joystick button and move it up or down,
you can scrolls through the saved channels you want.
NOTE
Adjusting the menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items ( , , , ) moving the joystick button up, down, left or right.
TV Off
Settings
Input List
Close
Turn the power off.
Accesses the main menu.
Changes the input source.
Clears on-screen displays and returns to TV viewing.
ENGLISH
yyWith your finger over the joystick button, move it up, down, left or right, be careful not to press
the joystick button. If you press the joystick button first, you can not adjust the volume level and/
or scroll through saved channels.
12
ASSEMBLING AND PREPARING
Lifting and Moving the TV
When moving or lifting the TV, read the
following to prevent the TV from being
scratched or damaged and for safe
transportation regardless of its type and size.
CAUTION
yyAvoid touching the screen at all times, as
this may result in damage to the screen.
yyDo not place the product on the floor
with its front facing down without
padding. Failure to do so may result in
damage to the screen.
Setting up the TV
Attaching the Stand
CAUTION
yyWhen attaching the stand to the TV
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
yyIt is recommended to move the TV in
the box or packing material that the TV
originally came in.
yyBefore moving or lifting the TV, disconnect
the power cord and all cables.
ENGLISH
yyWhen holding the TV, the
screen should face away
from you to avoid damage.
yyHold the top and bottom of the TV
frame firmly. Make sure not to hold the
transparent part, speaker, or speaker grill
area.
A Stand Base
1
1
2
B Stand Base
2
(For 42/47/55LY340C)
4 EA
M4 x L14
(For 32LY340C)
4 EA
M4 x L20
yyUse at least two people to
move a large TV.
yyWhen transporting the TV by
hand, hold the TV as shown
in the following illustration.
yyWhen transporting the TV, do not expose
the TV to jolts or excessive vibration.
yyWhen transporting the TV, keep the TV
upright; never turn the TV on its side or tilt
towards the left or right.
ASSEMBLING AND PREPARING
Mounting on a Table
1
13
Securing the TV to a wall (optional)
Lift and tilt the TV into its upright position on
a table.
-L
eave a 10 cm (minimum) space from the
wall for proper ventilation.
(Depending on model)
10 cm
10 cm
10 cm
m
10 c
1
CAUTION
yyDo not place the TV near or on sources
of heat, as this may result in fire or other
damage.
2 Mount the wall brackets with the bolts to
the wall.
Match the location of the wall bracket and
the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets
tightly with a sturdy rope or cable.
Make sure to keep the rope parallel to the
flat surface.
CAUTION
yyMake sure that children do not climb on
or hang on the TV.
NOTE
yyUse a platform or cabinet that is strong
and large enough to support the TV
securely.
yyBrackets, bolts, and ropes, are optional.
You can obtain additional accessories
from your local dealer.
ENGLISH
2 Connect the power cord to a wall outlet.
Insert and tighten the eye-bolts, or TV
brackets and bolts on the back of the TV.
- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
14
ASSEMBLING AND PREPARING
Mounting on a Wall
CAUTION
An optional wall mount can be used with your
LG Television. Consult with your local dealer for
a wall mount that supports the VESA standard
used by your TV model. Carefully attach the
wall mount bracket at the rear of the TV.
Install the wall mount bracket on a solid wall
perpendicular to the floor. If you are attaching
the TV to other building materials, please
contact qualified personnel to install the wall
mount. Detailed instructions will be included
with the wall mount.
We recommend the use of LG’s wall mount
bracket.
When you do not use LG’s wall mount bracket,
please use wall mount bracket which the
distance to the wall is adequately secured for
seamless connectivity to external devices.
yyDisconnect the power before moving
or installing the TV. Otherwise electric
shock may occur.
yyIf you install the TV on a ceiling or slanted
wall, it may fall and result in severe
injury. Use an authorized LG wall mount
and contact the local dealer or qualified
personnel. When using a third-party wall
mount, it is not covered by the warranty.
yyDo not over tighten the screws as this
may cause damage to the TV and void
your warranty.
yyUse the screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an
improper accessory are not covered by
the warranty.
NOTE
ENGLISH
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mounts that
meet the VESA standard. Standard dimensions
for the wall mount kits are described in the
following table.
Model
32LY340C
42/47/55LY340C
200 x 200
400 x 400
M6
M6
VESA (A x B)
A
B
Standard screw
Number of screws 4
4
Wall mount
bracket (optional)
LSW440B
MSW240
LSW240B
MSW240
yyUse the screws that are listed in the
VESA standard screw specifications.
yyThe wall mount kit includes an installation
manual and necessary parts.
yyThe wall mount bracket is optional. You
can obtain additional accessories from
your local dealer.
yyThe length of screws may differ
depending upon the wall mount. Make
sure to use the proper length.
yyFor more information, refer to the manual
supplied with the wall mount.
yyWhen attaching a wall mounting bracket
to the TV, insert the wall mount inner
spacers into the TV wall mount holes to
adjust the vertical angle of the TV. (For
42LY340C)
Wall Mount
Spacers
MAKING CONNECTIONS
15
MAKING CONNECTIONS
yyImage shown may differ from your TV.
You can connect various external devices to the TV. Supported external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.
For more information on external device’s connection, refer to the manual provided with each device.
NOTE
yyIf you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input
cable to the TV through a DVD recorder or VCR. For more information about recording, refer to
the manual provided with the connected device.
yyThe external device connections shown may differ slightly from illustrations in this manual.
ANTENNA
of the TV port.
yyConnect external devices to the TV regardless about the order
IN with the gaming device.
yyIf you connect a gaming device to the TV, use the cable supplied
yyRefer to the external equipment’s manual for operating instructions.
yyOnly a USB storage device is recognizable.
yyIf the USB storage device is connected through a USB hub, the device is not recognizable.
yyUsing a DVI to HDMI cable may cause compatibility issues.
Connecting to an Antenna or Cable
VHF Antenna
UHF Antenna
ANTENNA
IN
Antenna
Coaxial (75Ω)
or
CABLE
IN
(*Not provided)
CAUTION
yyMake sure not to bend the copper wire
of the RF cable.
Copper wire
yyComplete all connections between
devices,
CABLE and then connect the power
cordINto the power outlet to prevent
damage to your TV.
Wall Jack
Coaxial (75Ω)
(*Not provided)
NOTE
yyTo improve the picture quality in a poor
signal area, please purchase a signal
amplifier and install it properly.
yyUse a signal splitter to use more than 2
TVs.
yyIf the antenna is not installed properly,
contact your dealer for assistance.
yyDTV Audio Supported Codec: MPEG,
Dolby Digital, Dolby Digital Plus, HE-AAC,
DRA
ENGLISH
Connect an antenna, cable, or cable box to watch TV. The illustrations may differ from the actual items
and an RF cable is optional.
16
MAKING CONNECTIONS
Other Connections
Connect your TV to external devices. For the best picture and audio quality, connect digital devices
using an HDMI cable. Cables not provided.
GND
R
Digital Audio System
Speaker (8Ω)
OPTICAL AUDIO IN
EXTERNAL
SPEAKER OUT
RGB IN (PC)
USB IN
1
RS 232C IN (CONTROL & SERVICE)
CABLE
IN
H/P OUT
RED
WHITE
RED
WHITE
YELLOW
L
YELLOW
VIDEO
PR
RED
WHITE
PB
RED
WHITE
RED
BLUE
GREEN
AUDIO OUT
RED
BLUE
GREEN
RED
WHITE
Y
RGB OUT (PC)
PB
PR L/MONO AUDIO R
COMPONENT IN / AV IN
AUDIO IN (RGB)
VIDEO/ Y
ANTENNA
IN
R
AUDIO
VIDEO L/MONO AUDIO R
Blu-Ray / HD Cable Box / DVD / VCR
PC
IN 2 (MHL)
ENGLISH
OPTICAL
DIGITAL
AUDIO OUT
L
GND
MAKING CONNECTIONS
17
Blu-Ray / HD Cable Box / HD STB / DVD / PC
HDMI
DVI OUT
AUDIO OUT
RED
WHITE
USB IN
EXTERNAL
SPEAKER OUT
1
CABLE
IN
PB
PR L/MONO AUDIO R
COMPONENT IN / AV IN
MHL Cable
ANTENNA
IN
AUDIO IN (RGB)
VIDEO/ Y
USB
IN 2 (MHL)
RS 232C IN (CONTROL & SERVICE)
Mobile
phone
H/P OUT
RGB IN (PC)
RED
WHITE
Headphone
AUDIO OUT
DVI OUT
HDMI
Blu-Ray / HD STB /HD Cable Box / DVD
ENGLISH
OPTICAL
DIGITAL
AUDIO OUT
18
REMOTE CONTROL
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly. To install batteries, open
the battery cover, replace batteries (1.5 V AAA) matching the
and
ends to
the label inside the compartment, and close the battery cover. Failure to match the
correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury,
or ambient pollution. To remove the batteries, perform the installation actions in reverse.
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
yyIn Analogue TV and some countries, some remote control buttons may not work.
This remote uses infrared light. When in use, it should be pointed in the direction of the TV’s remote
sensor.
(POWER) Turns the TV on or off.
ꕊ 節能模式 ENERGY SAVING Adjusts the brightness of the screen to reduce
energy consumption.
ENGLISH
AV 模式 AV MODE Selects an AV mode.
輸入 INPUT Changes the input source.
1
2
3
4
5
6
Number button Enters numbers.
7
8
9
頻道返回 Q.VIEW Tunes to the last channel viewed.
0
FAV
TV/RAD Selects Radio, TV and DTV programme.
所有頻道 LIST Accesses the saved channel list.
音量
Adjusts the volume level.
喜愛頻道 FAV Accesses your favorite channel list.
畫面比例 RATIO Resizes an image.
静音 MUTE
頻道 P
翻頁
Mutes all sounds.
Scrolls through the saved channels.
Moves to the previous or next screen.
節目導覽 GUIDE Displays and removes the electronic program guide.
選單 HOME Selects a menu. Clears all on-screen displays and returns to TV
viewing from any menu.
簡易選單 Q.MENU Accesses the quick menu.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
確認 OK
Selects menus or options and confirms your input.
返回 BACK Returns to the previous screen.
節目資訊
離開
INFO Shows information on the current program.
EXIT Clears all on-screen displays and returns to TV viewing.
Color buttons (
: Red,
: Green,
special functions in some menus.
: Yellow,
: Blue) These access
Control buttons ( , , , , ) Controls the MY MEDIA menus or the
SIMPLINK compatible devices (USB, SIMPLINK).
menu.
SUBTITLE
Accesses the AV devices connected to the TV. Opens the SIMPLINK
字幕 SUBTITLE Activates your preferred subtitle in digital mode.
MAINTENANCE
19
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep it at peak performance and to extend the product’s lifespan.
CAUTION
yyBefore cleaning, turn the power off and disconnect the power cord and all other cables.
yyWhen the TV is left unattended or unused for a long time, disconnect the power cord from the
wall outlet to prevent possible damage from lightning or power surges.
Screen, Frame, Cabinet, and Stand
To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
Power Cord
Remove the accumulated dust or dirt on the power cord regularly.
ENGLISH
yyDo not push, rub, or hit the surface with your fingernail or a sharp object, as this may result in
scratches on the screen and image distortions.
yyDo not use any chemicals, such as waxes, benzene, alcohol, thinners, insecticides, air
fresheners, or lubricants, as these may damage the screen’s finish and cause discoloration.
yyDo not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
20
TROUBLESHOOTING
TROUBLESHOOTING
The software may be updated for improvement in performance. The customer is responsible to ensure
the compatibility of their equipment with any LG Electronics software. If needed, please consult
with LG Electronics and update new software versions according to the guidance provided by LG
Electronics.
Problem
Solution
ENGLISH
Cannot control the TV with
the remote control.
yyCheck if anything such as tape has been placed over the receiver.
yyCheck if there is any obstacle between the product and the remote
control.
yyReplace the batteries with new fresh ones.
No image display and no
sound is produced.
yyCheck if the product is turned on.
yyCheck if the power cord is connected to a wall outlet.
yyCheck if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
yyCheck the power control settings. The power supply may be
interrupted.
yyCheck if the auto off feature is activated in the Time settings.
When connecting to the
PC (RGB/HDMI DVI), ‘No
signal’ or ‘Invalid Format’
is displayed.
yyTurn the TV off/on using the remote control.
yyReconnect the RGB/HDMI DVI cable.
yyRestart the PC with the TV on.
SPECIFICATIONS
21
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
Television System
Hong Kong
Channel Coverage
Digital TV
Analogue TV
DTMB
PAL-D/K/B/G/I, NTSC-M
DTMB : 21~69
External Antenna
Impedance
BAND
PAL-D/K/B/G/I
NTSC-M
VHF/UHF
1~69
2~78
Cable
1~47
1~71
75 Ω
Operating Temperature 0 °C - 40 °C
Operating Humidity
Environment
Storage Temperature
Condition
Storage Humidity
Power Requirement
Less than 80 %
-20 °C - 60 °C
Less than 85 %
AC 100-240 V ~ 50 / 60 Hz
MODELS
Dimensions
(W x H x D)
Weight
Weight
42LY340C
(42LY340C-CA)
With stand
732 x 481 x 207 (mm)
961 x 612 x 218 (mm)
Without stand
732 x 431 x 55.5 (mm)
961 x 567 x 55.5 (mm)
With stand
6.2 kg
9.5 kg
Without stand
6.0 kg
9.2 kg
47LY340C
(47LY340C-CA)
55LY340C
(55LY340C-CA)
MODELS
Dimensions
(W x H x D)
32LY340C
(32LY340C-CA)
With stand
1,073 x 676 x 247 (mm)
1,243 x 772 x 247 (mm)
Without stand
1,073 x 629 x 55.8 (mm)
1,243 x 725 x 56.8 (mm)
With stand
12.7 kg
18.4 kg
Without stand
12.3 kg
18 kg
ENGLISH
For the power supply and power consumption, refer to the label attached to the product.
22
SPECIFICATIONS
RGB (PC), HDMI (PC) supported mode
(HDMI IN 2 does not support PC mode.)
Resolution
Horizontal
Frequency (kHz)
31.47
70.09
640 x 480
31.469
59.94
720 x 400
31.468
70.08
800 x 600
37.879
60.317
1024 x 768
48.363
60.004
1152 x 864
54.348
60.053
1360 x 768
47.712
60.015
63.981
60.02
(FHD only)
1920 x 1080
(FHD only)
67.50
60.00
HDMI (DTV) supported mode
ENGLISH
Resolution
720 x 480p
720 x 576p
1280 x 720p
1920 x 1080i
1920 x 1080p
Horizontal
Frequency (kHz)
Component ports on the TV
Y
Vertical
Frequency (Hz)
640 x 350
1280 x 1024
Component port connecting information
Vertical
Frequency (Hz)
31.469
59.94
31.50
60.00
31.25
50.00
37.50
50.00
44.96
59.94
45.00
60.00
28.125
50.00
33.72
59.94
33.75
60.00
26.97
23.97
27.00
24.00
33.716
29.976
33.75
30.00
56.25
50.00
67.43
59.94
67.50
60.00
Video output ports on DVD player
Signal
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
Component supported mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
15.63
59.94
15.73
60.00
31.47
59.94
31.50
60.00
720 x 576i
15.625
50.00
720 x 576p
31.25
50.00
44.96
59.94
45.00
50.00
45.00
60.00
28.125
50.00
33.72
59.94
33.75
60.00
26.97
23.976
27.00
24.00
33.71
29.97
33.75
30.00
56.25
50.00
67.432
59.94
67.50
60.00
720 x 480i
720 x 480p
1280 x 720p
1920 x 1080i
1920 x 1080p
IR CODES
23
IR CODES
(Depending on model)
Code
(Hexa)
Function
08
(POWER)
Note
Code
(Hexa)
Function
Note
Remote control Button 8F
(Power On/Off)
◄◄
Remote control Button
畫面比例 RATIO
Remote control Button
30
AV 模式 AV MODE
Remote control Button
79
0B
輸入 INPUT
Remote control Button
7E
Remote control Button
Remote control Button
AB
節目導覽 GUIDE
Remote control Button
10-19
Number Key 0-9
Remote control Button
39
字幕 SUBTITLE
Remote control Button
53
所有頻道 LIST
Remote control Button
95
ꕊ 節能模式
ENERGY SAVING
Remote control Button
1A
頻道返回 Q.VIEW
Remote control Button
0C
門戶 PORTAL
Remote control Button
02
音量 (VOL)
Remote control Button
43
選單 HOME
Remote control Button
03
音量 (VOL)
Remote control Button
TV/RAD
F0
喜愛頻道 FAV
Remote control Button
静音 MUTE
Remote control Button
00
頻道 P
翻頁
Remote control Button
01
頻道 P
翻頁
Remote control Button
45
簡易選單 Q.MENU
Remote control Button
28
返回 BACK
Remote control Button
AA
節目資訊
5B
離開
44
確認 OK
Remote control Button
40
^
Remote control Button
41
v
Remote control Button
07
<
Remote control Button
06
>
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
B1
ꕗ
Remote control Button
B0
►
Remote control Button
BA
ꕘ
Remote control Button
8E
►►
Remote control Button
EXIT
INFO
Remote control Button
Remote control Button
ENGLISH
1E
09
24
EXTERNAL CONTROL DEVICE SETUP
EXTERNAL CONTROL
DEVICE SETUP
Type of Connector;
D-Sub 9-Pin Male
1
5
RS-232C Setup
Connect the RS-232C (serial port) input jack to
an external control device (such as a computer
or an A/V control system) to control the
product’s functions externally.
Connect the serial port of the control device to
the RS-232C jack on the product back panel.
6
9
RS-232C IN
(CONTROL & SERVICE)
No.
RS 232C IN (CONTROL & SERVICE)
ENGLISH
NOTE
yyRS-232C on this unit is intended to
be used with third party RS-232C
control hardware and software. The
instructions below are provided to help
with programming software or to test
functionality using telenet software. RS232C connection cables are not supplied
with the product.
Pin name
1
No connection
2
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No connection
7
No connection
8
No connection
9
No Connection
EXTERNAL CONTROL DEVICE SETUP
RS-232C Configurations
Set ID
7-Wire Configuration
(Serial female-female NULL modem cable)
PC
TV
2
3
TXD
TXD
3
2
RXD
GND
5
5
GND
DTR
4
6
DSR
DSR
6
4
DTR
RTS
7
8
CTS
CTS
8
7
RTS
3 Press the Navigation buttons to scroll to Set
ID and press OK.
4 Scroll left or right to select a set ID number
and select CLOSE. The adjustment range is
1-99.
5 When you are finished, press EXIT.
2
3
TXD
TXD
3
2
RXD
GND
5
5
GND
DTR
4
6
DSR
DSR
6
4
DTR
RTS
7
8
CTS
CTS
8
7
RTS
D-Sub 9
ENGLISH
TV
RXD
D-Sub 9
1 Press HOME to access the main menus.
2 Press the Navigation buttons to scroll to
D-Sub 9
3-Wire Configurations(Not standard)
PC
Set ID number; “Real Data Mapping”
Option and press OK.
RXD
D-Sub 9
25
26
EXTERNAL CONTROL DEVICE SETUP
Communication Parameters
yyBaud rate: 9600 bps (UART)
yyData length: 8 bits
yyParity : None
yyStop bit: 1 bit
yyCommunication code: ASCII code
yyUse a crossed (reverse) cable.
Command Reference List
(Depending upon model)
01. Power
COMMAND1 COMMAND2
DATA
(Hexadecimal)
k
00 - 01
a
COMMAND1 COMMAND2
DATA
(Hexadecimal)
13. Balance
k
t
00 - 64
x
u
00 - 64
ENGLISH
02. Aspect
Ratio
k
c
(See p. 28)
14. Color
Temperature
03. Screen
Mute
k
d
(See p. 28)
15. Energy
Saving
j
q
00 - 05
04. Volume
Mute
k
e
00 - 01
16. Auto
j
Configuration
u
01
05. Volume
Control
k
f
00 - 64
17. Equalize
j
v
(See p. 30)
06. Contrast k
g
00 - 64
18. Tune
Command
m
a
(See p. 30)
07.
Brightness
k
h
00 - 64
19. Program
Add/Skip
m
b
00 - 01
08. Color
k
i
00 - 64
20. Key
m
c
(See p. 31)
09. Tint
k
j
00 - 64
21. Control
Back Light
m
g
00 - 64
10.
Sharpness
k
k
00 - 32
22. Input
x
Select (Main)
b
(See p. 31)
11. OSD
Select
k
l
00 - 01
12. Remote
Control
Lock Mode
k
m
00 - 01
* Note: During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are
not executed and treated as NG.
EXTERNAL CONTROL DEVICE SETUP
27
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV.(j, k, m or x)
[Command 2] : Second command to control the TV.
[Set ID] : You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment
range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled. Set ID is indicated as
decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on transmission/receiving protocol.
[DATA] : To transmit command data. Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
OK Acknowledgement
The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this
time, if the data is data read mode, it indicates present status data. If the data is data write mode, it
returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data 00 : Illegal Code
ENGLISH
[Command2][ ][Set ID][ ][OK][Data][x]
28
EXTERNAL CONTROL DEVICE SETUP
01. Power (Command: k a)
► To control Power On/Off of the set
Transmission [k][a][ ][Set ID][ ][Data][Cr]
03. Screen Mute (Command: k d)
► To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00: Power Off
Data 01: Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data 00: Screen mute off (Picture on),
Video-out Mute off
Data 01: Screen mute on (Picture off)
Data 10: Video Mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
►To show Power On/Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’
data based on this format, Acknowledgement
data feed back presents status about each
function.
* OK Ack., Error Ack. and other message may
display on the screen when TV is power On.
ENGLISH
02. Aspect Ratio (Command: k c) (Main Picture
Size)
► To adjust the screen format. (Main picture
format) You can also adjust the screen format
using the Aspect Ratio in the Q.MENU. or
PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
*In case of video mute on only, TV will display
On Screen Display(OSD). But, in case of Screen
mute on, TV will not display OSD.
04. Volume Mute (Command: k e)
► To control volume mute on/off.
You can also adjust mute using the MUTE
button on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00: Volume mute on (Volume off)
Data 01: Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
Data 01: Normal s creen (4:3)
Data 02: Wide screen (16:9)
Data 04: Zoom
Data 06: Original
Data 07: 14:9
Data 09: Just Scan
Data 0B: Full Wide
Data 10 to 1F: Cinema Zoom 1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
► To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
* Using the PC input, you select either 16:9 or
4:3 screen aspect ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p
50Hz / 60 Hz, 1080p 24 Hz / 30 Hz / 50 Hz / 60
Hz), Component( 720p, 1080i, 1080p 50 Hz / 60
Hz) mode, Just Scan is available.
* Full Wide is supported only for Digital.
06. Contrast (Command: k g)
► To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64
*Refer to Real data mapping.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
Data Min: 00 ~ Max: 64
*Refer to Real data mapping.
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
07. Brightness (Command: k h)
► To adjust screen brightness.
You can also adjust brightness in the PICTURE
menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64
*Refer to Real data mapping.
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
08. Color (Command: k i)
► To adjust the screen color.
You can also adjust color in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64
*Refer to Real data mapping.
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
Data Red: 00 ~ Green: 64
*Refer to Real data mapping.
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
► To adjust screen sharpness.
You can also adjust sharpness in the PICTURE
menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 32
*Refer to Real data mapping.
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
► To select OSD (On Screen Display) on/off
when controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00: OSD off Data 01: OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
12. Remote Control Lock Mode (Command: k m)
► To lock the front panel controls on the
monitor and remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00: Lock off Data 01: Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use
this mode. When main power is on/off, external
control lock is released.
* In the standby mode, if key lock is on, TV will
not turn on by power on key of IR & Local Key.
13. Balance (Command: k t)
► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64
*Refer to Real data mapping.
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
14. Color Temperature (Command: x u)
► To adjust color temperature.
To adjust colour temperature. You can also
adjust Colour Temperature in the PICTURE
menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64
*Refer to Real data mapping.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
09. Tint (Command: k j)
► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
29
30
EXTERNAL CONTROL DEVICE SETUP
15. Energy Saving (Command: j q)
► To reduce the power consumption of the TV.
You can also adjust Energy Saving in PICTURE
menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Power Saving
Function
17. Equalize (Command: j v)
► To adjust eqalize.
Transmission [ j ][v][ ][Set ID][ ][Data][Cr]
MSB
0
LSB
0
0
0
0
0
0
0
Description
Level
7
6
5
4
3
2
1
0
0
0
0
0
Low
Power
0
0
0
0
0
0
0
1
Frequency
Off
Frequency
4
3
2
1
0
Step
Minimum
0 0 0 1st Band
0
0
0
0
0
0(decimal)
0 0 1 2nd Band
0
0
0
0
1
1(decimal)
0 1 0 3rd Band
... ... ... ... ...
0
0
0
0
Low
Power
0
0
0
0
Low
Power
0
0
1
0
Medium
0
0
0
0
Low
Power
0
0
1
1
Maximum
ENGLISH
0
0
0
0
Low
Power
0
1
0
1
Screen Off
0
0
0
0
Low
Power
0
1
0
0
Auto
► ‘Auto’ is available in TV that supports
‘Intelligent Sensor’
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
7 6 5
Data
...
0 1 1 4th Band
1
0
0
1
1
19(decimal)
1 0 0 5th Band
1
0
1
0
0
20(decimal)
Ack [v][ ][Set ID][ ][OK/NG][Data][x]
18. Tune Command (Command: m a)
► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][
][Data2][Cr]
16. Auto Configuration (Command: j u)
► To adjust picture position and minimize
image shaking automatically. It works only in
RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01: To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Data 00: High channel data
Data 01: Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH)
DTV No. 0 -> Don’t care
Data 02: [Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data Min: 00 to Max: 7DH
EXTERNAL CONTROL DEVICE SETUP
19. Program Add/Del (Command: m b)
► To set skip status for the current Program.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00: Skip
Data 01: Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
20. Key (Command: m c)
► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data
0
0
0
0
Input 1
0
0
0
1
Input 2
0
0
1
0
Input 3
0
0
1
1
Input 4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
*Real data mapping
00 : Step 0
…
Data Key Code - See p. 23
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Input Number
31
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
…
21. Color Back Light (Command: m g)
► To adjust screen backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
…
A : Step 10 (SET ID 10)
64 : Step 100
22. Input Select (Command: x b)
(Main Picture Input)
► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
73 : Step 115
74 : Step 116
Data Structure
FE : Step 254
FF : Step 255
…
Data Min:00 ~ Max:64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
0
LSB
0
0
0
External Input
External Input
0
0
0
0
Input Number
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
HDMI
…
…
MSB
…
CF : Step 199
ENGLISH
6E : Step 110
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
MODEL
SERIAL
Download PDF

advertising