LG | 65EG9650 | LG 55EG9200 Owner's manual

OWNER’S MANUAL
Please read this manual carefully before operating your set and retain
it for future reference.
EG92**
EG96**
www.lg.com
2
TABLE OF CONTENTS
TABLE OF CONTENTS
ENGLISH
ENG
3LICENSES
28
3
29MAINTENANCE
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
4
SAFETY INSTRUCTIONS
10
- Viewing 3D Imaging (Only 3D Models)
11
INSTALLATION PROCEDURE
11
ASSEMBLING AND PREPARING
29
29
29
USING THE USER GUIDE
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
29TROUBLESHOOTING
30SPECIFICATIONS
11Unpacking
13
Separate purchase
14
Parts and buttons
15
- Using the joystick button
16
Lifting and moving the TV
17
Setting up the TV
17
- Attaching the stand
20
Mounting on a table
21
Mounting on a wall
21
Tidying cables
22
MAKING CONNECTIONS
22
Antenna Connection
23
HDMI connection
24
DVI to HDMI connection
24
Component connection
25
Composite connection
25
Audio connection
25
- Digital optical audio connection
26Headphone connection
26
USB connection
27
MAGIC REMOTE FUNCTIONS
28
28
28
28
28
Registering magic remote
- How to register the magic remote
- How to deregister the magic remote
- How to use magic remote
Precautions to take when using the magic
remote
WARNING
• If you ignore the warning message, you may be seriously
injured or there is a possibility of accident or death.
CAUTION
• If you ignore the caution message, you may be slightly
injured or the product may be damaged.
NOTE
• The note helps you understand and use the product safely.
Please read the note carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE INFORMATION
3
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
ENGLISH
ENG
OPEN SOURCE SOFTWARE NOTICE INFORMATION
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge.
com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost
of media, shipping, and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you
purchased the product.
4
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the
product.
ENGLISH
ENG
WARNING
Do not place the TV and/or remote control in the following
environments:
• A location exposed to direct sunlight
• An area with high humidity such as a bathroom
• Near any heat source such as stoves and other devices that
produce heat
• Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
• An area exposed to rain or wind
• Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or
product deformation.
Do not place the product where it might be exposed to dust. This may
cause a fire hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not
secured completely into socket, fire ignition may break out.
Ensure the power cord does not come into contact with hot objects
such as a heater. This may cause a fire or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
Bend antenna cable between inside and outside building to prevent
rain from flowing in. This may cause water damaged inside the
Product and could give an electric shock.
When mounting TV onto wall make sure to neatly install and isolate
cabling from rear of TV as to not create possibility of electric shock /
fire hazard.
Do not touch the power plug with wet hands. Additionally, if the cord
pin is wet or covered with dust, dry the power plug completely or wipe
dust off. You may be electrocuted due to excess moisture.
Do not plug too many electrical devices into a single multiple electrical
outlet. Otherwise, this may result in fire due to over-heating.
SAFETY INSTRUCTIONS
Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire
into the product, or inflammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, fire or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
icca
nt
Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suffocation. Keep it out
of the reach of children.
Do not let your children climb or cling onto the TV. Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) between power cable plug and input Wall Socket
while it is connected to the input terminal on the wall. Additionally,
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)
Do not put or store inflammable substances near the product. There is
a danger of combustion/explosion or fire due to careless handling of
the inflammable substances.
Do not spray water on the product or scrub with an inflammable
substance (thinner or benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a thunder or lighting
storm. You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a fire or a burn by a spark.
Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur. Contact the service centre for check, calibration or repair.
ENGLISH
ENG
Des
5
6
SAFETY INSTRUCTIONS
If any of the following occur, unplug the product immediately and
contact your local service centre.
ENGLISH
ENG
• The product has been impacted by shock
• The product has been damaged
• Foreign objects have entered the product
• The product produced smoke or a strange smell
This may result in fire or electric shock.
If water or another substance enters the product (like a AC adapter,
power cord, TV), disconnect the power cord and contact the service
centre immediately. Otherwise, this may result in fire or electric shock.
Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction or product deformation.
Unplug the TV from AC mains wall socket if you do not intend to use
the TV for a long period of time. Accumulated dust can cause fire
hazard and insulation deterioration can cause electric leakage/shock/
fire.
Never Disassemble the AC adapter or power cord.
This may result in fire or electric shock.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Handle the adapter carefully to avoid dropping or striking it. An impact
could damage the adapter.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
SAFETY INSTRUCTIONS
7
CAUTION
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when the
antenna falls. This may cause an electric shock.
Do not install the product on places such as unstable shelves or
inclined surfaces. Also avoid places where there is vibration or where
the product cannot be fully supported. Otherwise, the product may fall
or flip over, which may cause injury or damage to the product.
Only use the specified type of battery. This could cause damage to the
remote control.
Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight , open fireplace and electric heaters.
Do not place non-rechargeable batteries in charging device.
If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which
may cause injury.
If you intend to mount the product to a wall, attach standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts),
fix it carefully so as not to drop.
Only use the attachments / accessories specified by the manufacturer.
When installing the antenna, consult with a qualified service
technician. If not installed by a qualified technician, this may create a
fire hazard or an electric shock hazard.
Make sure there are no objects between the remote control and its
sensor.
Signal from Remote Control can be interrupted due to external/
internal lighting eg Sunlight, fluorescent lighting. If this occurs turn
off lighting or darken viewing area.
When connecting external devices such as video game consoles, make
sure the connecting cables are long enough. Otherwise, the product
may fall over, which may cause injury or damage the product.
ENGLISH
ENG
Install the product where no radio wave occurs.
We recommend that you maintain a distance of at least 2 to 7 times
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
8
SAFETY INSTRUCTIONS
ENGLISH
ENG
Do not turn the product On/Off by plugging-in or unplugging the
power plug to the wall outlet. (Do not use the power plug for switch.) It may cause mechanical failure or could give an electric shock.
Do not press strongly upon the panel with a hand or sharp object such
as nail, pencil or pen, or make a scratch on it, as it may cause damage
to screen.
Please follow the installation instructions below to prevent the
product from overheating.
Avoid touching the screen or holding your finger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
• The distance between the product and the wall should be more
than 10 cm.
• Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
• Do not install the product on a carpet or cushion.
• Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
Take care not to touch the ventilation openings when watching the TV
for long periods as the ventilation openings may become hot. This does
not affect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,
benzene, alcohol etc., which can damage the product and its panel. Otherwise, this may result in fire, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this unit
by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling
at the plug.
Don’t pull at the cord to unplug the power cord from the power board,
as this could be hazardous.
Prevent dust collecting on the power plug pins or outlet. This may
cause a fire hazard.
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
When moving the product, make sure you turn the power off first.
Then, unplug the power cables, antenna cables and all connecting
cables. The TV set or power cord may be damaged, which may create a fire
hazard or cause electric shock.
SAFETY INSTRUCTIONS
When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
Displaying a still image (e.g., broadcasting channel logo, on-screen
menu, scene from a video game or computer screen) for a prolonged
time may cause damage to the screen, resulting in retention of the
image, which is known as image sticking. It can remain for long time
or never disappear. The warranty does not cover the product for image
sticking. Avoid displaying a fixed image on your television’s screen for a
prolonged period (1 or more hours for OLED). Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking
may occur on the borders of the panel. This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
Generated Sound
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
The panel is a high technology display product with resolution of two
million to six million pixels. You may see tiny black dots and/or brightly
coloured dots (red, blue or green) at a size of 1 ppm on the panel. This
does not indicate a malfunction and does not affect the performance
and reliability of the product. This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
You may find different brightness and colour of the panel depending
on your viewing position(left/right/top/down). This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
“Cracking” noise: A cracking noise that occurs when watching or
turning off the TV is generated by plastic thermal contraction due to
tempera-ture and humidity. This noise is common for products where
thermal deformation is required. Electrical circuit humming/panel
buzzing: A low level noise is generated from a high-speed switching
circuit, which supplies a large amount of current to operate a product.
It varies depend-ing on the product. This generated sound does not affect the performance and reliability
of the product.
Do not use high voltage electrical goods near the TV(e.g. electric
mosquito-swatter). This may result in product malfunction.
ENGLISH
ENG
Contact the service centre once a year to clean the internal parts of
the product. Accumulated dust can cause mechanical failure.
9
10
SAFETY INSTRUCTIONS
Viewing 3D Imaging (Only 3D Models)
WARNING
Viewing Environment
ENGLISH
ENG
• Viewing Time
-- When watching 3D contents, take 5 - 15 minute breaks
every hour. Viewing 3D contents for a long period of time
may cause headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure
or chronic illness
• Some users may experience a seizure or other abnormal
symptoms when they are exposed to a flashing light or particular
pattern from 3D contents.
• Do not watch 3D videos if you feel nausea, are pregnant and/ or
have a chronic illness such as epilepsy, cardiac disorder, or blood
pressure disease, etc.
• 3D Contents are not recommended to those who suffer from
stereo blindness or stereo anomaly. Double images or discomfort
in viewing may be experienced.
• If you have strabismus (cross-eyed), amblyopia (weak eyesight)
or astigmatism, you may have trouble sensing depth and easily
feel fatigue due to double images. It is advised to take frequent
breaks than the average adult.
• If your eyesight varies between your right and left eye, revise your
eyesight prior to watching 3D contents.
Symptoms which require
discontinuation or refraining from
watching 3D contents
• Do not watch 3D contents when you feel fatigue from lack of
sleep, overwork or drinking.
• When these symptoms are experienced, stop using/watching 3D
contents and get enough rest until the symptom subsides.
-- Consult your doctor when the symptoms persist.
Symptoms may include headache, eyeball pain, dizziness,
nausea, palpitation, blurriness, discomfort, double image,
visual inconvenience or fatigue.
CAUTION
Viewing Environment
• Viewing Distance
-- Maintain a distance of at least twice the screen diagonal
length when watching 3D contents. If you feel discomfort
in viewing 3D contents, move further away from the TV.
Viewing Age
• Infants/Children
-- Usage/ Viewing 3D contents for children under the age of
5 are prohibited.
-- Children under the age of 10 may overreact and become
overly excited because their vision is in development (for
example: trying to touch the screen or trying to jump into
it. Special monitoring and extra attention is required for
children watching 3D contents.
-- Children have greater binocular disparity of 3D
presentations than adults because the distance between
the eyes is shorter than that of adults. Therefore they will
perceive more stereoscopic depth compared to adults for
the same 3D image.
• Teenagers
-- Teenagers under the age of 19 may react with sensitivity
due to stimulation from light in 3D contents. Advise them
to refrain from watching 3D contens for a long time when
they are tired.
• Elderly
-- The elderly may perceive less 3D effect compared to the
young. Do not sit closer to the TV than the recommended
distance.
Cautions when using the 3D glasses
• Make sure to use LG 3D glasses. Otherwise, you may not be able
to view 3D videos properly.
• Do not use 3D glasses instead of your normal glasses, sunglasses
or protective goggles.
• Using modified 3D glasses may cause eye strain or image
distortion.
• Do not keep your 3D glasses in extremely high or low
temperatures. It will cause deformation.
• The 3D glasses are fragile and are easily scratched. Always use a
soft, clean piece of cloth when wiping the lenses. Do not scratch
the lenses of the 3D glasses with sharp objects or clean/wipe
them with chemicals.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
11
NOTE
•
•
•
•
•
INSTALLATION PROCEDURE
1
2
3
Open the package and make sure all the accessories are included.
Connect an external device to the TV set.
Make sure the network connection is available. You can use the TV network functions only when the network connection is made.
* If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few minutes.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
• Do not use any unapproved items to ensure the safety and product life span.
• Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
• Some models have a thin film attached on to the screen and this must not be removed.
NOTE
• The items supplied with your product may vary depending on the model.
• Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.
• For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension
cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.
B
B
A
*A ≤ 10 mm
*B ≤ 18 mm
A
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.
• Recommended HDMI Cable Types (3m or less)
- High-Speed HDMI®/TM Cable
- High-Speed HDMI®/TM Cable with Ethernet
ENGLISH
ENG
Image shown may differ from your TV.
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
The available menus and options may differ from the input source or product model that you are using.
New features may be added to this TV in the future.
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned off if it will not be watched
for some time, as this will reduce energy consumption.
• The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the
overall running cost.
12
ASSEMBLING AND PREPARING
ENGLISH
ENG
Magic remote, Batteries (AA)
(See p. 27)
Owner’s manual
Component gender cable
(See p. 24)
Composite gender cable
(See p. 24, 25)
Stand Body / Stand Base
(Only 55EG92**)
(See p. 17)
Stand Body / Stand Base
(Only 55EG96**)
(See p. 17)
Stand Screw
5 EA, M4 x L20
(Only 55EG92**, 55EG96**)
8 EA, M4 x L20
(Only 65EG96**)
(See p. 17, 19)
Cinema 3D glasses
The number of 3D glasses may differ
depending on the model or country.
Cable Holder
(See p. 21)
Stand Body / Stand Base
(Only 65EG96**)
(See p. 18)
ASSEMBLING AND PREPARING
13
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AN-MR600
Magic Remote
AN-VC550
Smart Camera
AG-F***DP
Dual Play Glasses
LG Audio Device
Compatibility
EG92**
EG96**
AG-F***
Cinema 3D Glasses
•
•
AN-MR600
Magic Remote
•
•
AN-VC550
Smart Camera
•
•
AG-F***DP
Dual Play Glasses
•
•
LG Audio Device
•
•
The model name or design may be changed depending on the upgrade of product functions, manufacturer’s circumstances or policies.
ENGLISH
ENG
AG-F***
Cinema 3D Glasses
14
ASSEMBLING AND PREPARING
Parts and buttons
Screen
ENGLISH
ENG
Speakers
Joystick Button2
Remote Control Sensor and Intelligent Sensor1
Power Indicator (EG92**)
Power LG Logo Light (EG96**)
1
2
Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. (Depending on model)
Joystick Button - This button is located below the TV screen.
NOTE
• You can set the LG Logo Light to on or off by selecting GENERAL in the main menus. (Depending on model)
ASSEMBLING AND PREPARING
15
Using the joystick button
You can operate the TV by pressing the button or moving the joystick left, right, up, or down.
Basic Functions
When the TV is turned off, place your finger on the joystick button and press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick button and press it once for a few
seconds and release it. All running apps will close, and any recording in progresswill stop.
Volume Control
If you place your finger over the joystick button and move it left or right, you can adjust the
volume level you want.
Programmes
Change
If you place your finger over the joystick button and move it up or down, you can scrolls through
the saved programmes you want.
NOTE
• When your finger over the joystick button and push it to the up, down, left or right, be careful not to press the joystick button. If you press
the joystick button first, you may not be able to adjust the volume level and saved programmes.
Adjusting the Menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items moving the joystick button up, down, left or right.
Turns the power off.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Accesses the Quick Settings.
ENGLISH
ENG
Power On
16
ASSEMBLING AND PREPARING
Lifting and moving the TV
Please note the following advice to prevent the TV from being
scratched or damaged and for safe transportation regardless of its type
and size.
• When transporting a large TV, there should be at least 2 people.
• When transporting the TV by hand, hold the TV as shown in the
following illustration.
ENGLISH
ENG
CAUTION
• Avoid touching the screen at all times, as this may result in
damage to the screen.
• It is recommended to move the TV in the box or packing material
that the TV originally came in.
• Before moving or lifting the TV, disconnect the power cord and
all cables.
• When holding the TV, the screen should face away from you to
avoid damage.
• Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
• When transporting the TV, do not expose the TV to jolts or
excessive vibration.
• When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
• Do not apply excessive pressure to cause flexing /bending of
frame chassis as it may damage screen.
• Be sure to keep your TV upright instead of laying or tilting it
while moving the TV.
• When handling the TV, be careful not to damage the protruding
joystick button.
17
ASSEMBLING AND PREPARING
Setting up the TV
3
Image shown may differ from your TV.
Attaching the stand
55EG92**, 55EG96**
ENGLISH
ENG
1
1
Protective Package
1
5 EA
M4 x L20
Stand Cover
1 When assembling the stand, lay the front screen Protective Package
included in the product box on a table or flat surface and then place
the TV screen face down on the Protective Package.
4
CAUTION
• Do not lift your TV without the stand. The protruding Joystick
Button may be damaged.
Stand Cover
2
Stand Body /
Stand Base
Stand Body /
Stand Base
CAUTION
• Insert the protruding parts of the Stand Cover into the holes.
18
ASSEMBLING AND PREPARING
65EG96**
5
Stand
Cover
1
1
ENGLISH
ENG
Protective Package
1
Stand Cover
1 When assembling the stand, lay the front screen Protective Package
included in the product box on a table or flat surface and then place
the TV screen face down on the Protective Package.
CAUTION
Cover Holder
CAUTION
• Do not lift your TV without the stand. The protruding Joystick
Button may be damaged.
2
• Insert the Cover Holder of the Stand Cover into the holes
until it clicks. Press the Stand Cover gently so that the nonwoven fabric inside is attached tightly.
Stand Body /
Stand Base
19
ASSEMBLING AND PREPARING
3
5
Stand
Cover
ENGLISH
ENG
Stand Body /
Stand Base
8 EA
M4 x L20
4
Cover Holder
Stand Cover
Stand Body /
Stand Base
CAUTION
• Insert the Cover Holder of the Stand Cover into the holes
until it clicks. Press the Stand Cover gently so that the nonwoven fabric inside is attached tightly.
CAUTION
• When attaching the stand to the TV set, place the screen
facing down on a cushioned table or flat surface to protect
the screen from scratches.
• Make sure that the screws are inserted correctly and
fastened securely. (If they are not fastened securely enough,
the TV may tilt forward after being installed.)
Do not use too much force and over tighten the screws;
otherwise screw may be damaged and not tighten correctly.
CAUTION
• Insert the protruding parts of the Stand Cover into the holes.
NOTE
• Remove the stand before installing the TV on a wall mount
by performing the stand attachment in reverse.
20
ASSEMBLING AND PREPARING
Mounting on a table
1
Securing the TV to a wall
Lift and tilt the TV into its upright position on a table.
-- Leave a 10 cm (minimum) space from the wall for proper
ventilation.
(This feature is not available for all models.)
ENGLISH
ENG
10 cm
10 cm
10 cm
10 cm
1
2
5 cm
10 cm
3
Insert and tighten the eye-bolts, or TV brackets and bolts on the
back of the TV.
-- If there are bolts inserted at the eye-bolts position,
remove the bolts first.
Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the
rear of the TV.
Connect the eye-bolts and wall brackets tightly with a sturdy
rope.
Make sure to keep the rope horizontal with the flat surface.
CAUTION
• Make sure that children do not climb on or hang on the TV.
NOTE
2
Connect the power cord to a wall outlet.
CAUTION
• Do not place the TV near or on sources of heat, as this may
result in fire or other damage.
• Use a platform or cabinet that is strong and large enough to
support the TV securely.
• Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
ASSEMBLING AND PREPARING
Mounting on a wall
CAUTION
10 cm
10 cm
NOTE
10 cm
10 cm
Make sure to use screws and wall mount bracket that meet the
standard. Standard dimensions for the wall mount kits are described in
the following table.
Separate purchase(Wall Mounting Bracket)
AxBxC
55EG92**
55EG96**
200 x 340 x 195
65EG96**
200 x 330 x 120
A
A
B
• Use the screws that are listed on the standard screw
specifications.
• The wall mount kit includes an installation manual and
necessary parts.
• The wall mount bracket is not provided. You can obtain
additional accessories from your local dealer.
• The length of screws may differ depending on the wall
mount. Make sure to use the proper length.
• For more information, refer to the manual supplied with the
wall mount.
Tidying cables
Image shown may differ from your TV.
Gather and bind the cables with the cable holder.
B
C
Standard screw
Number of
screws
• Disconnect the power first, and then move or install the TV.
Otherwise electric shock may occur.
• If you install the TV on a ceiling or slanted wall, it may fall
and result in severe injury.
Use an authorized LG wall mount and contact the local
dealer or qualified personnel.
• Do not over tighten the screws as this may cause damage to
the TV and void your warranty.
• Use the screws and wall mounts that meet the standard.
Any damages or injuries by misuse or using an improper
accessory are not covered by the warranty.
C
M6
4
OTW150
Wall mount
bracket
Cable Holder
CAUTION
• Do not move the TV by holding the cable holder, as the cable
holder may break, and injuries and damage to the TV may
occur.
ENGLISH
ENG
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel.
LG recommends that wall mounting be performed by a qualified
professional installer.
Model
21
22
MAKING CONNECTIONS
MAKING CONNECTIONS
This section on MAKING CONNECTIONS mainly uses diagrams for the
EG96** models.
Antenna Connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
VHF Antenna
UHF Antenna
ENGLISH
ENG
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
Antenna
or
(*Not
Provided)
NOTE
• The external device connection may differ from the model.
• Connect external devices to the TV regardless of the order of
the TV port.
• If you record a TV program on a DVD recorder or VCR, make
sure to connect the TV signal input cable to the TV through
a DVD recorder or VCR. For more information of recording,
refer to the manual provided with the connected device.
• Refer to the external equipment’s manual for operating
instructions.
• If you connect a gaming device to the TV, use the cable
supplied with the gaming device.
• In PC mode, there may be noise associated with the
resolution, vertical pattern, contrast or brightness. If noise is
present, change the PC output to another resolution, change
the refresh rate to another rate or adjust the brightness and
contrast on the PICTURE menu until the picture is clear.
• In PC mode, some resolution settings may not work properly
depending on the graphics card.
• If Ultra HD content is played via PC, the video or audio may
have disruptions intermittently depending on your PC’s
performance.
Wall Antenna Socket
NOTE
• Use a signal splitter to use more than 2 TVs.
• If the image quality is poor, install a signal amplifier properly
to improve the image quality.
• If the image quality is poor with an antenna connected, try
to realign the antenna in the correct direction.
• An antenna cable and converter are not provided.
• Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital
Plus, HE-AAC.
• This TV cannot receive UHD (3840 x 2160 pixels) broadcasts
directly because the related standards have not been
confirmed.
MAKING CONNECTIONS
HDMI connection
Transmits the digital video and audio signals from an external device
to the TV. Connect the external device and the TV with the HDMI cable
as shown.
→
→ Picture → HDMI ULTRA HD Deep Colour
→
-- On: Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0)
-- Off: Support 4K @ 60 Hz (4:2:0)
• The external device connection may differ from the model.
• It is recommended to use the TV with the HDMI connection
for the best image quality.
• Use the latest High Speed HDMI™ Cable with CEC (Customer
Electronics Control) function.
• High Speed HDMI™ Cables are tested to carry an HD signal
up to 1080p and higher.
• Supported HDMI Audio format : Dolby Digital (32 KHz, 44.1
KHz, 48 KHz), DTS (44.1 KHz, 48 KHz), PCM (32 KHz, 44.1
KHz, 48 KHz, 96 KHz, 192 KHz)
HDMI
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
ARC (Audio Return Channel)
• An external audio device that supports SIMPLINK and ARC
must be connected using HDMI(4K @ 60 Hz)/DVI IN 2 (ARC)
port.
• When connected with a high-speed HDMI cable, the
external audio device that supports ARC outputs optical
SPDIF without additional optical audio cable and supports
the SIMPLINK function.
ENGLISH
ENG
If the device connected to Input Port also supports ULTRA HD Deep
Colour, your picture may be clearer. However, if the device doesn’t
support it, it may not work properly.
In that case, connect the device to a different HDMI port or change the
TV’s ULTRA HD Deep Colour setting to Off. (This feature is available on
certain models which are supported ULTRA HD Deep Colour only.)
NOTE
(*Not Provided)
23
24
MAKING CONNECTIONS
DVI to HDMI connection
Transmits the digital video signal from an external device to the TV.
Connect the external device and the TV with the DVI-HDMI cable as
shown. To transmit an audio signal, connect an audio cable.
Component connection
Transmits analogue video and audio signals from an external device to the
TV. Connect the external device and the TV with a component gender cable
as shown.
ENGLISH
ENG
IN
AV
AV
VIDEO
IN
COMPONENT
AUDIO
PR
PB
Y
( Audio in)
(*Not
Provided)
GREEN
BLUE
RED
RED
GREEN
BLUE
RED
RED
GREEN
BLUE
(*Not Provided)
L
RED
WHITE
• Depending on the graphics card, DOS mode may not work if
a HDMI to DVI Cable is in use.
• When using the HDMI / DVI cable, Single link is only supported.
RED
NOTE
WHITE
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
GREEN
(Use the component gender
cable provided.)
WHITE
DVI OUT
YELLOW
AUDIO OUT
YELLOW
(Use the composite gender
cable provided.)
R
AUDIO
VIDEO
DVD / Blu-Ray / HD Cable Box
NOTE
• If cables are not installed correctly, it could cause this image
to display in black and white or with distorted colours.
MAKING CONNECTIONS
Composite connection
25
Audio connection
Transmits analogue video and audio signals from an external device
to the TV. Connect the external device and the TV with a composite
gender cable as shown.
You may use an external audio system instead of the built-in speaker.
Digital optical audio connection
AV
VIDEO
IN
COMPONENT
AUDIO
PR
PB
Y
YELLOW
(Use the composite
gender cable provided.)
WHITE
RED
WHITE
YELLOW
RED
YELLOW
(*Not Provided)
(*Not Provided)
OPTICAL AUDIO IN
L (MONO) AUDIO R
RED
DVD / Blu-Ray /
HD Cable Box / VCR
WHITE
YELLOW
VIDEO
Digital Audio System
CAUTION
• Do not look into the optical output port. Looking at the laser
beam may damage your vision.
• Audio with ACP (Audio Copy Protection) function may block
digital audio output.
ENGLISH
ENG
Transmits a digital audio signal from the TV to an external device.
Connect the external device and the TV with the optical audio cable as
shown.
26
MAKING CONNECTIONS
Headphone connection
USB connection
(Only EG96**)
Transmits the headphone signal from the TV to an external device. Connect the external device and the TV with the headphone as shown.
Connect a USB storage device such as a USB flash memory, external
hard drive or a USB memory card reader to the TV and access the Smart
Share menu to use various multimedia files.
ENGLISH
ENG
Headphone
HDD
(*Not Provided)
(*Not Provided)
NOTE
• AUDIO menu items are disabled when connecting a headphone.
• Optical Digital Audio Out is not available when connecting
a headphone.
• Headphone impedance: 16 Ω
• Max audio output of headphone: 0.627 mW to 1.334 mW
• Headphone jack size: 0.35 cm
HUB
(*Not Provided)
USB
(*Not Provided)
NOTE
• Some USB Hubs may not work. If a USB device connected
using a USB Hub is not detected, connect it to the USB IN
port on the TV directly.
• Connect the external power source if your USB is needed.
• Connecting via USB 3.0 : Some USB device may not work if it
dose not meet USB 3.0 standard. In case, connect it to USB
IN 2 or USB IN 3 port.
MAGIC REMOTE FUNCTIONS
27
MAGIC REMOTE FUNCTIONS
When the message “Magic Remote battery is low. Change the battery.” is displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching and ends to the label
inside the compartment, and close the battery cover. Be sure to point the remote control toward the remote
control sensor on the TV.
To remove the batteries, perform the installation actions in reverse.
ENGLISH
ENG
CAUTION
• Do not mix old and new batteries, as this may damage the remote control.
• In Analogue TV and some countries, some remote control buttons may not work.
1. @
2 abc
3 def
4 ghi
5 jkl
6 mno
7pqrs
8 tuv
9wxyz
LIST
0
INFO
EXIT
GUIDE
TEXT
T.OPT
SUBT.
(POWER) Turns the TV on or off.
(INPUT) Changes the input source.
* Pressing and holding the button displays all the lists of external inputs.
Number buttons Enters numbers.
Accesses the saved programmes list.
(Space) Opens an empty space on the screen keyboard.
Views the information of the current programmes and screen.
Adjusts the volume level.
Scrolls through the saved programmes.
(MUTE) Mutes all sounds.
By pressing the AD button, audio descriptions function will be enabled. (Depending on model)
(HOME) Accesses the Home menu.
(BACK) Returns to the previous screen.
Clears on-screen displays and returns to Last Input viewing.
Wheel (OK) Press the center of the Wheel button to select a menu. You can change
programmes by using the wheel button.
Navigation buttons
(up/down/left/right) Press the up, down, left or right button
to scroll the menu. If you press
buttons while the pointer is in use, the pointer will
disappear from the screen and Magic Remote will operate like a general remote control. To display
the pointer on the screen again, shake Magic Remote to the left and right.
Shows programme guide.
(Screen Remote) Displays the Screen Remote.
*Accesses the Universal Control Menu. (Depending on model)
Used for viewing 3D video. (Only 3D models)
(Voice recognition)
Network connection is required to use the voice recognition function.
1. Press the voice recognition button.
2. Speak when the voice display window appears on the left of the
TV screen.
• Use the Magic Remote no further than 10 cm from your face.
• The voice recognition may fail when you speak too fast or too slowly.
• The recognition rate may vary depending on the user’s characteristics (voice, pronunciation,
intonation, and speed) and the environment (noise and TV volume).
(Q. Settings) Accesses the Quick Settings.
Coloured buttons These access special functions in some menus.
( : Red,
: Green,
: Yellow,
: Blue)
TELETEXT buttons(
,
) These buttons are used for teletext.
Recalls your preferred subtitle in digital mode.
28
MAGIC REMOTE FUNCTIONS / USING THE USER GUIDE
Registering magic remote
USING THE USER GUIDE
How to register the magic remote
User Guide allows you to more easily access the detailed TV information.
ENGLISH
ENG
To use the Magic Remote, first pair it with your TV.
1 Put batteries into the Magic Remote and turn the TV on.
2 Point the Magic Remote at your TV and press the Wheel (OK) on
the remote control.
* If the TV fails to register the Magic Remote, try again after turning
the TV off and back on.
1 Press the
(Home) button to access the Home menu.
2 Select User Guide and press the
Wheel(OK) button.
How to deregister the magic remote
Press and hold the
(BACK) and
(HOME) buttons at the same
time for five seconds, to unpair the Magic Remote with your TV.
* Pressing and holding the
button will let you cancel and reregister Magic Remote at once.
How to use magic remote

• Shake the Magic Remote slightly to the right and left or press
(HOME), (INPUT),
buttons to make the pointer
appear on the screen.
(In some TV models, the pointer will appear when you turn the
Wheel (OK) button.)
• If the pointer has not been used for a certain period of time or
Magic Remote is placed on a flat surface, then the pointer will
disappear.
• If the pointer is not responding smoothly, you can reset the
pointer by moving it to the edge of the screen.
• The Magic Remote depletes batteries faster than a normal remote
due to the additional features.
Precautions to take when using
the magic remote
• Use the remote control within the specified range (within 10 m).
You may experience communication failures when using the
device outside the coverage area or if there are obstacles within
the coverage area.
• You may experience communication failures depending on the
accessories.
Devices such as a microwave oven and wireless LAN operate in the
same frequency band (2.4 GHz) as the Magic Remote. This may
cause communication failures.
• The Magic Remote may not work properly if a wireless router (AP)
is within 1 meter of the TV.
Your wireless router should be more than 1 m away from the TV.
• Do not disassemble or heat the battery.
• Do not drop the battery. Avoid extreme shocks to the battery.
• Inserting the battery in the wrong way may result in explosion.
MAINTENANCE / TROUBLESHOOTING
MAINTENANCE
Cleaning your TV
CAUTION
• Make sure to turn the power off and disconnect the power cord
and all other cables first.
• When the TV is left unattended and unused for a long time,
disconnect the power cord from the wall outlet to prevent
possible damage from lightning or power surges.
Screen, frame, cabinet and stand
• To remove dust or light dirt, wipe the surface with a dry, clean,
and soft cloth.
• To remove major dirt, wipe the surface with a soft cloth dampened
in clean water or a diluted mild detergent. Then wipe immediately
with a dry cloth.
CAUTION
• Avoid touching the screen at all times, as this may result in
damage to the screen.
• Do not push, rub, or hit the screen surface with your fingernail
or a sharp object, as this may result in scratches and image
distortions.
• Do not use any chemicals as this may damage the product.
• Do not spray liquid onto the surface. If water enters the TV, it may
result in fire, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Cannot control the TV with the remote control.
• Check the remote control sensor on the product and try again.
• Check if there is any obstacle between the product and the remote
control.
• Check if the batteries are still working and properly installed ( to , to ).
No image display and no sound is produced.
• Check if the product is turned on.
• Check if the power cord is connected to a wall outlet.
• Check if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
• Check the power control settings. The power supply may be
interrupted.
• Check if the Sleep Timer or Off Time feature is activated in the
TIME settings.
• If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI/DVI), ‘No signal’ or ‘Invalid Format’
is displayed.
• Turn the TV off/on using the remote control.
• Reconnect the HDMI/DVI cable.
• Restart the PC with the TV on.
ENGLISH
ENG
Clean your TV regularly to keep the best performance and to extend
the product lifespan.
29
30
SPECIFICATIONS
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
Thickness
Depth
ENGLISH
ENG
EG92**
55EG9200-CA
MODELS
With stand (mm)
Dimensions
(W x H x T(D))
1225 x 762 x 191
Without stand (mm)
1225 x 719 x 48.9(87.3)
With stand (kg)
Weight
16.5
Without stand (kg)
13.2
Power requirement
AC 100-240 V~ 50 / 60 Hz
EG96**
MODELS
Dimensions
(W x H x T(D))
Weight
With stand (mm)
Without stand (mm)
55EG9600-CA
55EG9650-CA
65EG9600-CA
65EG9650-CA
1226 x 760 x 213
1447 x 884 x 237
1226 x 719 x 50.1(87.8)
1447 x 842 x 50.1(102.5)
With stand (kg)
19
26.9
Without stand (kg)
15.3
Power requirement
Environment condition
21.7
AC 100-240 V~ 50 / 60 Hz
Operating Temperature
0 °C ~ 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C ~ 60 °C
Storage Humidity
Less than 85 %
Digital TV
Analogue TV
Television System
DTMB
PAL D/K, PAL I, NTSC M
Programme Coverage
DTMB : 21~69
PAL D/K : VHF/UHF 1~69, CATV 1~47
PAL I : VHF/UHF 1~69, CATV 1~47
NTSC M : VHF/UHF 2~78, CATV 1~71
External Antenna Impedance
75 Ω
SPECIFICATIONS
31
Wireless module(LGSBW41)Specifications
Wireless LAN
Bluetooth
IEEE 802.11a/b/g/n
Standard
Bluetooth Version 4.0
Frequency Range
2400 to 2483.5MHz
5150 to 5250 MHz
5725 to 5850 MHz
Frequency Range
2400 to 2483.5 MHz
Output Power
(Max.)
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4 GHz: 16 dBm
802.11n - 5 GHz: 16 dBm
Output Power
(Max.)
10 dBm or Lower
ENGLISH
ENG
Standard
• Because band channel used by the country could be different, the user can not change or adjust the operating frequency and this product is
set for the regional frequency table.
• This device should be installed and operated with minimum distance 20 cm between the device and your body. And this phrase is for the
general statement for consideration of user environment.
Record the model number and serial
number of the TV.
Refer to the label on the back cover
and quote this information to your
dealer when requiring any service.
MODEL
SERIAL
OWNER’S MANUAL
EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
www.lg.com
2
KEY CODES
ENGLISH
ENG
KEY CODES
• This feature is not available for all models.
Code
(Hexa)
Function
Note
Code
(Hexa)
Function
Note
00
CH +, PR +
R/C Button
53
List
R/C Button
01
CH -, PR -
R/C Button
5B
Exit
R/C Button
02
Volume +
R/C Button
60
PIP(AD)
R/C Button
03
Volume -
R/C Button
61
Blue
R/C Button
06
> (Arrow Key / Right Key)
R/C Button
63
Yellow
R/C Button
07
< (Arrow Key / Left Key)
R/C Button
71
Green
R/C Button
08
Power
R/C Button
72
Red
R/C Button
09
Mute
R/C Button
79
Ratio / Aspect Ratio
R/C Button
0B
Input
R/C Button
91
AD (Audio Description)
R/C Button
0E
SLEEP
R/C Button
7A
User Guide
R/C Button
0F
TV, TV/RAD
R/C Button
7C
Smart / Home
R/C Button
R/C Button
7E
SIMPLINK
R/C Button
10 - 19 * Number Key 0 - 9
1A
Q.View / Flashback
R/C Button
8E
►► (Forward)
R/C Button
1E
FAV (Favorite Channel)
R/C Button
8F
◄◄ (Rewind)
R/C Button
20
Text (Teletext)
R/C Button
AA
Info
R/C Button
21
T. Opt (Teletext Option)
R/C Button
AB
Program Guide
R/C Button
28
Return (BACK)
R/C Button
B0
► (Play)
R/C Button
30
AV (Audio / Video) Mode
R/C Button
B1
ꕗ (Stop / File List)
R/C Button
39
Caption/Subtitle
R/C Button
BA
ꕘ (Freeze / Slow Play /
Pause)
R/C Button
40
Λ (Arrow Key / Cursor Up)
R/C Button
BB
Soccer
R/C Button
41
V (Arrow Key / Cursor
Down)
R/C Button
BD
ꔄ (REC)
R/C Button
42
My Apps
R/C Button
DC
3D
R/C Button
43
Menu / Settings
R/C Button
99
AutoConfig
R/C Button
44
OK / Enter
R/C Button
9F
App / *
R/C Button
45
Q.Menu
R/C Button
4C
List, - (ATSC Only)
R/C Button
* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
EXTERNAL CONTROL DEVICE SETUP
3
• Image shown may differ from your TV.
Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.
Note: The type of control port on the TV can be different between model series.
* Please be advised that not all models support this type of connectivity.
* Cable is not provided.
USB to Serial converter with USB Cable
USB IN
USB Type
(PC)
(TV)
• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product
ID :IN0x2008) USB to serial converter
RS-232C
(CONTROL & SERVICE)
which is not made nor provided by LG.
• It can be purchased from computer stores that carry accessories for IT support professionals.
(TV)
(PC)
USB IN
RS-232C With RS232C Cable
(PC)
(TV)
SERVICE ONLY
DE9 (D-Sub 9pin) Type
1
• You need to purchase the RS-232C (DE9, D-Sub
3 9pin female-to-female type) to RS-232C cable required
for the connection between the PC and the TV, which is specified in the manual.
(PC)
2
RS-232C IN
(CONTROL & SERVICE)
(PC)
SERVICE ONLY
1
3
RS-232C IN
(CONTROL & SERVICE)
2
(PC)
(TV)
1
3
(PC)
The connection interface may differ from your TV.
(TV)
2
(TV)
(TV)
1
3
(PC)
RS-232C IN
2
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
(TV)
ENGLISH
ENG
EXTERNAL CONTROL DEVICE SETUP
USB USB
IN IN
4
EXTERNAL CONTROL DEVICE SETUP
(PC)
(PC)
(TV)
(TV)
RS-232C IN
(CONTROL
SERVICE)
• You need to purchase the phone-jack to RS-232 cable required
for &the
connection between the PC and
the TV, which is specified in the manual.
RS-232C IN
(PC)
(PC)
(CONTROL & SERVICE)
* For other models, connect to the USB port.
* The connection interface may differ from your TV.
1
3
(PC)
(PC)
1
3
2
2
- or
(TV)
(TV)
(TV)
(TV)
1
3
(PC)
(PC)
SERVICE
ONLY ONLY
SERVICE
ENGLISH
ENG
Phone jack Type
1
3
RS-232C IN
(CONTROL & SERVICE)
2
RS-232C IN
(CONTROL & SERVICE)
2
Customer Computer
(TV)
(TV)
RS-232C configurations
3-Wire Configurations(Not standard)
1
5
PC
RXD
RS-232C IN
(CONTROL & SERVICE)
TXD
RS-232C IN
(CONTROL & SERVICE)
GND
6
2
2
TXD
3
1
RXD
5
3
GND
OR
9
RS-232C
(Serial port)
TV
RXD
3
2
TXD
TXD
2
1
RXD
GND
5
3
GND
D-Sub 9
Phone
Set ID
For Set ID number, see "Real Data Mapping" on p.6
1. Press SETTINGS to access the main menus.
2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.
3. Press the Navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
* (Depending on model)
EXTERNAL CONTROL DEVICE SETUP
5
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
ENGLISH
ENG
Communication Parameters
• Stop bit : 1 bit
• Communication code : ASCII code
• Use a crossed (reverse) cable.
Command reference list
(Depending on model)
COMMAND1 COMMAND2
DATA
(Hexadecimal)
01. Power*
k
a
00 to 01
02. Aspect
Ratio
k
c
(p.7)
03. Screen
Mute
k
d
(p.7)
k
e
00 to 01
k
f
00 to 64
06. Contrast
k
g
00 to 64
07.
Brightness
k
h
00 to 64
08. Color/
Colour
k
i
00 to 64
04. Volume
Mute
05. Volume
Control
09. Tint
k
10.
k
Sharpness
11. OSD
k
Select
12. Remote
Control Lock k
Mode
j
00 to 64
k
00 to 32
l
00 to 01
m
00 to 01
13. Treble
k
r
00 to 64
14. Bass
k
s
00 to 64
COMMAND1 COMMAND2
DATA
(Hexadecimal)
15. Balance k
16. Color
(Colour)
x
Temperature
17. ISM
Method (Only j
Plasma TV)
t
00 to 64
u
00 to 64
p
(p.8)
18. Equalizer j
v
(p.8)
q
00 to 05
a
(p.9)
b
00 to 01
19. Energy
j
Saving
20. Tune
m
Command
21. Channel m
(Programme)
Add/Del(Skip)
22. Key
m
c
Key Codes
23. Control
Backlight,
Control Panel
Light
24. Input
select (Main)
25. 3D (Only
3D models)
26. Extended
3D (Only 3D
models)
27. Auto
Configure
m
g
00 to 64
x
b
(p.11)
x
t
(p.11)
x
v
(p.11)
j
u
(p.12)
* Note:During playing or recording media, all commands except Power (ka) and Key (mc) are not
executed and treated as NG.
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
6
EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV.
[Set ID]
:You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set
can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return - ASCII code ‘0x0D’
[ ]
: Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
* When you enter the [data] in hexadecimal, refer to following conversion table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0
01 : Step 1 (Set ID 1)
...
0A : Step 10 (Set ID 10)
...
0F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
...
32 : Step 50 (Set ID 50)
33 : Step 51 (Set ID 51)
...
63 : Step 99 (Set ID 99)
...
C7 : Step 199
C8 : Step 200
...
FE : Step 254
FF : Step 255
...
01 00 : Step 256
...
27 0E : Step 9998
27 0F : Step 9999
...
EXTERNAL CONTROL DEVICE SETUP
7
01.Power (Command: k a)
►► To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]
* Similarly, if other functions transmit ‘FF’ data
based on this format, Acknowledgement feedback
presents status about each function.
02.Aspect Ratio (Command: k c)
(Main Picture Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen 07 : 14:9
(4:3)
(Europe, Colombia, Mid-East,
02 : Wide screen
Asia except South Korea and
(16:9)
Japan)
04 : Zoom
09 : * Just Scan
05 : Zoom 2
0B : Full Wide
(Latin America
(Europe, Colombia, Midexcept Colombia
East, Asia except South
Only)
Korea and Japan)
06 : Set by Program/ 10 to 1F : C
inema Zoom 1
Original
to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
04.Volume Mute (Command: k e)
►► To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05.Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06.Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition),
Just Scan is available.
* Full wide mode may work differently based on
model and is supported for DTV fully, and ATV,
AV partially.
07.Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE
menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
03.Screen Mute (Command: k d)
►► To select screen mute on/off.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
08.Color/Colour (Command: k i)
►► To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
ENGLISH
ENG
* Commands may work differently depending on model and signal.
8
EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
Data Min : 00 to Max : 64
* (Depending on model)
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
09.Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10.Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE
menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
14. Bass (Command: k s)
►► To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model)
15.Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
16.Color(Colour) Temperature (Command: x u)
11.OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
►► To adjust colour temperature. You can also adjust
Color(Colour) Temperature in the PICTURE menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
17.ISM Method (Command: j p) (Only Plasma TV)
12.Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
►► To control the ISM method. You can also adjust
ISM Method in OPTION menu.
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data Min : 02: Orbiter
08: Normal
20: Color(Colour) Wash
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
When main power is off & on (plug-off and plug-in,
after 20 - 30 seconds), external control lock is
released.
18.Equalizer (Command : j v)
►► Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
* In the standby mode (DC off by off timer or ‘ka’,
‘mc’ command), and if key lock is on, TV will not
turn on by power on key of IR & Local Key.
0
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
0
0
0
0
Frequency
13. Treble (Command: k r)
►► To adjust treble.
You can also adjust in the AUDIO menu.
LSB
0
0
0
Data
7
6
5
Frequency
4
3
2
1
0
Step
0
0
0
1st Band
0
0
0
0
0
0(decimal)
0
0
1
2nd Band
0
0
0
0
1
1(decimal)
0
1
0
3rd Band
...
...
...
...
...
...
0
1
1
4th Band
0
0
0
1
1
19(decimal)
EXTERNAL CONTROL DEVICE SETUP
0
0
5th Band
0
0
1
0
1
20(decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
* It depends on model, and can adjust when sound
mode is EQ adjustable value.
19.Energy Saving (Command: j q)
►► To reduce the power consumption of the TV. You
can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Data
00 : Off
01 : Minimum
02 : Medium
03 : Maximum
04 : Auto (For LCD TV / LED TV) /
Intelligent sensor (For PDP TV)
05 : Screen off
* (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
Set ID = All = 00
Data 00 & 01 = Channel Data is 10 = 00 0a
Data 02 = Analog Antenna TV = 00
Result = ma 00 00 0a 00
2.Tune to the digital antenna (DVB-T) Channel 01.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1 = 00 01
Data 02 = Digital Antenna TV = 10
Result = ma 00 00 01 10
3.Tune to the satellite (DVB-S) Channel 1000.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1000 = 03 E8
Data 02 = Digital Satellite TV = 40
Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
• For South Korea, North/Latin America except
Colombia Model
►► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
20.Tune Command (Command: m a)
* This command may work differently depending on
model and signal.
• For Europe, Mid-East, Colombia, Asia except
South Korea and Japan Model
►► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
* Analog Antenna/Cable
[Data 00][Data 01] Channel Data
Data00 : High byte channel data
Data01 : Low byte channel data
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog)
- 00 : Antenna TV (ATV)
- 80 : Cable TV (CATV)
* Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data
Data00 : High Channel data
Data01 : Low Channel data
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
Data02 : Input Source (Digital)
- 10 : Antenna TV (DTV)
- 20 : Antenna Radio (Radio)
- 40 : Satellite TV (SDTV)
- 50 : Satellite Radio (S-Radio)
- 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
* Tune Command Examples:
1.Tune to the Analog antenna (PAL) Channel 10.
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
the Physical number is not required when sending a
command in Digital.
* Analog Antenna/Cable
Data00 : Physical Channel Number
- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number
Data01 & 02: xx (Don't care)
Data03 & 04: xx (Don't care)
Data05: Input Source (Analog)
- 00 : Antenna TV (ATV)
- 01 : Cable TV (CATV)
* Digital Antenna/Cable
Data00 : xx (Don't care)
[Data 01][Data 02]: Major Channel Number
Data01 : High byte Channel Data
Data02 : Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number
Data03 : High byte Channel Data
Data04 : Low byte Channel Data
Data05 : Input Source (Digital)
- 02 : Antenna TV (DTV) – Use Physical Channel
Number
- 06 : Cable TV (CADTV) – Use Physical Channel
ENGLISH
ENG
1
9
10 EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
Number
- 22 : Antenna TV (DTV) – Don’t Use Physical
Channel Number
- 26 : Cable TV (CADTV) - Don’t Use Physical
Channel Number
- 46 : Cable TV (CADTV) – Use Major Channel
Number Only (One Part Channel)
Two bytes are available for each major and minor
channel data, but usually the low byte is used alone
(high byte is 0).
* Tune Command Examples:
1.Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analog Cable TV = 01
Total = ma 00 23 00 00 00 00 01
2.Tune to the digital antenna (ATSC) channel 30-3.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = Digital Antenna TV = 22
Total = ma 00 00 00 1E 00 03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
• For Japan Model
►► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Data 05 = Digital Antenna TV = 02
Total = ma 00 00 00 11 00 01 02
2.Tune to the BS (ISDB-BS) channel 30.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Don’t Care = 00 00
Data 05 = Digital BS TV = 07
Total = ma 00 00 00 1E 00 00 07
* This feature is varied based on the model.
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
21.Channel(Programme) Add/Del(Skip)
(Command: m b)
►► To skip current channel(programme) for next time.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Del(ATSC,ISDB)/Skip(DVB)
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Set the saved channel status to del(ATSC, ISDB)/
skip(DVB) or add.
22.Key (Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
* Digital Antenna/Satellite
Data 00: xx (Don't care)
DataKey code - p.2.
[Data 01][Data 02]: Major Channel Number
Data 01: High byte Channel Data
Data 02: Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
23.Control Backlight (Command: m g)
[Data 03][Data 04]: Minor/Branch Channel Number
(Don’t care in Satellite)
Data 03: High byte Channel Data
Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan)
- 02 : Antenna TV (DTV)
- 07 : BS (Broadcasting Satellite)
- 08 : CS1 (Communication Satellite 1)
- 09 : CS2 (Communication Satellite 2)
* Tune Command Examples:
1 Tune to the digital antenna (ISDB-T) channel 17-1.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 17 = 00 11
Data 03 & 04 = Minor/Branch is 1 = 00 01
01 : Add
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
• For LCD TV / LED TV
►► To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Control Panel Light (Command: m g)
• For Plasma TV
►► To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
00 : DTV
01 : CADTV
02 : Satellite DTV
10 : ATV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
O
01
X
X
X
02
X
X
X
03
X
O
O
[Data03][x]
[t][ ][Set ID][ ][NG][Data00][x]
21 : AV2
40 : Component1
60 : RGB
41 : Component2
90 : HDMI1
92 : HDMI3
91 : HDMI2
93 : HDMI4
26.Extended 3D(Command: x v) (only 3D models)
(Depending on model)
►► To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
[Data 01][Cr]
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
25.3D(Command: x t) (only 3D models)
(Depending on model)
►► To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][ ][Data 03][Cr]
* (Depending on model)
DataStructure
[Data 00]00 : 3D On
01 : 3D Off
02 : 3D to 2D
03 : 2D to 3D
[Data 01]00 : Top and Bottom
01 : Side by Side
02 : Check Board
03 : Frame Sequential
04 : Column interleaving
05 : Row interleaving
[Data 02]00 : Right to Left
01 : Left to Right
[Data 03]3D Effect(3D Depth): Min : 00 - Max : 14
(*transmit by Hexadecimal code)
* [Data 02], [Data 03] functions depend on model
and signal.
* If [Data 00] is 00 (3D On), [Data 03] has no
meaning.
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data
01], [Data 02] and [Data 03] have no meaning.
* If [Data 00] is 03 (2D to 3D), [Data 01] and
[Data 02] have no meaning.
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data
03] works when 3D Mode (Genre) is manual only.
* All 3D pattern options ([Data 01]) may not be
available according to broadcasting/video signal.
[Data 02]
O
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
20 : AV or AV1
[Data 01]
O
X : don’t care
[Data 00]
00
[Data 03]
[Data 00]3D option
00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
06 : 3D Color Correction
07 : 3D Sound Zooming
08 : Normal Image View
09 : 3D Mode (Genre)
[Data 01]It has own range for each 3D option
determined by [Data 00].
1) When[Data 00] is 00
00 : Right to Left
01 : Left to Right
2) When[Data 00] is 01, 02
DataMin: 0 - Max: 14 (*transmit by Hexadecimal
code)
Data value range(0 - 20) converts Viewpoint range
(-10 - +10) automatically (Depending on model)
* This option works when 3D Mode (Genre) is manual
only.
3) When[Data 00] is 06, 07
00 : Off
01 : On
4) When[Data 00] is 08
00 : Revert to 3D video from 3D-to-2D
converted 2D video
01 : Change 3D video to 2D video, except
2D-to-3D video
* If conversion condition doesn’t meet, command is
treated as NG.
5) When [Data 00] is 09
00 : Standard
02 : Cinema
04 : Manual
01 : Sport
03 : Extreme
05 : Auto
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]
[v][ ][Set ID][ ][NG][Data00][x]
ENGLISH
ENG
24.Input select (Command: x b)
(Main Picture Input)
11
12 EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
27.Auto Configure (Command: j u)
(Depending on model)
►► To adjust picture position and minimize image
shaking automatically. It works only in RGB (PC)
mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Download PDF

advertising