LG | 55EG9A7P | LG 55EG9A7P Owner's manual

OLED TV
EG9A7*
AA
X4
(M4 x L12)
www.lg.com
P/No: MFL69850901 (1704-REV00)
1
2
3
4
5
6
ANTENNA/
CABLE IN
HDMI IN
HDMI IN / ARC
USB IN
LAN
OPTICAL DIGITAL
AUDIO OUT
AV IN
COMPONENT IN
AV IN
VIDEO
L/MONO AUDIO R
COMPONENT IN
AUDIO
VIDEO
1
2
3
4
0
1
2
55EG9A7P-CA
1229
759
225
708
48.6
20.0
16.7
*MFL69850901*
安全及參考
請於操作產品前仔細閱讀本手冊並將其保留以供未來參考
之用。
*MFL69873002*
www.lg.com
P/NO : MFL69873002 (1705-REV01)
韓國印刷
Copyright ⓒ 2017 LG Electronics Inc. All Rights Reserved. 版權所有
警告! 安全指示
粵語
注意
觸電風險
請勿打開
注意: 為減低觸電風險,請勿移除蓋板(或背
板)。當中並無用戶可自行維修的組件。請
向合資格維修人員諮詢相關維修安排。
此標誌用作提醒使用者,產品的機殼內
有非絕緣保護的「危險電壓」,相關電壓的
強度足以構成觸電風險。
此標誌用作提醒使用者,電器附帶的相
關產品說明,已列出重要操作及保養(
維修)指示。
警告: 為減低火災或觸電風險,請勿將本產品
置於雨中或潮濕環境中。
••只能用乾布清潔。請勿將電視及遙控器放置於
下列環境:
-- 陽光直接照射之位置
-- 高濕度範圍,例如浴室
-- 發熱源附近例如煮食爐及其他發熱裝置
-- 輕易暴露於蒸氣或油煙如廚房工作範圍或放
濕器附近
-- 暴露於雨水或當風位置
-- 靠近儲水容器例如花樽
否則,可能導致火災、觸電、產品無法正常運作
或變形。
••請勿將產品放置在暴露於灰塵的地方。將可能
引致火災。
••從裝置拔下電源插頭。插頭必須保持易於操
作。
••請勿以濕手接觸電源插頭。若插頭蘇腳沾濕
或被灰塵覆蓋,請徹底弄乾電源插頭或擦拭灰
塵。過於潮濕有可能導致觸電。
••確保將電源線連接接地電流。(未有設置安全
地線的裝置除外。)有可能導致觸電或受傷。
••徹底固定電源線。
如電源線未徹底固定,則可能引起火災。
2
••確保電源線並無與發熱源(如暖爐)接觸。這
可能會導致火災或觸電危險。
••切勿將重物或產品本身置於電源線上。否則,
可能導致火災或觸電。
••將天線屈疊於建築物之間以防止雨水流入產
品。此有可能引致水分損壞產品內部並導致
觸電。
••於將電視安裝於牆上時,確保不要以電視背部
之電源 及信號線懸掛安裝。
此有可能導致火災、觸電。
••請勿於單個多重電力輸出插座使用過多電力裝
置。否則將有可能因過熱引發火災。
••請勿讓產品跌落或使其於與外部裝置連接時翻
倒。否則將可能導致受傷或產品損壞。
••請將包裝防潮材料或乙烯基包裝物料放置在兒
童無法觸及的地方。防潮材料為有害物質,不
可吞食。若不小心吞食,請用力使其吐出,並
前往鄰近醫院就醫。乙烯基包裝物亦可引起窒
息。請放置於兒童無法觸及的地方。
••切勿讓孩童攀爬於電視上。否則將導致電視翻
倒並引致嚴重受傷。
••於廢棄電池時注意以防止孩童吞食。如小孩不
慎吞食電池請尋求醫生協助即時就醫。
••請勿將任何金屬/導電物體(例如金屬筷子/餐
具/螺絲批),插入電源線插頭及牆壁電源插
座之間。另外,將電源線插入牆壁後,請勿立
即接觸。將可能導致觸電。
••請勿於產品附近放置或儲存易燃物品。可導
致因不慎處理易燃物品而引致着火/爆炸或火
災。
•• 請勿將金屬物體(例如錢幣、髮夾、筷子或
金屬絲等)或易燃物(如紙張及火柴)投入產
品內部。請特別格注意兒童安全。可能導致觸
電、發生火災或受傷。若有異物掉入產品內,
請拔除電源線,並聯絡服務中心。
••請勿於本產品上噴水,或用易燃物質(苯或稀
釋劑) 拭擦。可導致火災或觸電。
••請勿撞擊本產品,勿使任何物件掉入本產品
中,不可用物件拋擲屏幕。可能引致受傷或產
品損壞。
••雷電或颱風時,嚴禁觸碰本產品或天線。將可
能導致觸電。
••於氣體洩漏時,嚴禁觸碰入牆電源插座,並打
開窗戶通風。可能因火花引起火災或燒毀。
••建議於觀看電視時保持最少為螢幕對角線長度
2 至 7 倍之距離。如長時間觀看電視有可能導
致視力模糊。
••規定使用特定類型電池。此可能導致遙控器
損壞。
••請勿將新舊電池混合使用。此可導致電池過熱
及洩漏。
••電池不應暴露於高溫的地方。例如,避免產品
暴露於直射陽光下,開放式火爐及電暖爐邊。
••遙控器信號有可能受陽光或其他強光干擾。如
此情況發生,將室內環境調暗。
••當連接外部裝置如電視遊戲機時,確保連接線
有足夠長度。否則,可能因產品跌落或翻倒而
導致受傷或產品損壞。
••請勿以插入或拔除電源插頭方式開啟/關閉產
品。(請勿使用電源插頭作為開關用途。)此
可導致機件損壞或觸電可能。
••請遵從下列安裝指示以防止產品過熱。
-- 產品與牆壁的距離應超於 10 厘米。
-- 請勿將產品安裝於不通風位置(例如:書櫃
或櫥櫃內)。
-- 請勿將產品安裝於地毯或軟墊上。
-- 確保桌布或窗簾並無妨礙通風口。
可能引致火災。
••請注意於長時間觀看電視期間避免接觸通風
口因其可能散發熱力。此並不影響產品的運作
或性能。
••請定期檢查設備纜線,如外表受損或變形,請
立即拔除電源,停止使用設備,並請授權服務
商更換受損部份。
••防止灰塵積聚於電源插頭或插座上。將可能引
致火災。
••保護電源線以防止受到物理性如扭曲、折彎、
緊夾、受到門的擠壓或踩踏或機件受損。請加
倍留意插頭、 入牆插座以及裝置的電線出口。
••請勿以手或指甲、鉛筆或鋼筆等尖銳物件用力
按壓屏幕,或使其刮花。
••避免長時間接觸或以手指、握緊屏幕。如不遵
從將可導致螢幕短暫變形。
粵語
••請勿隨意自行拆開、維修或修改產品。可導
致火災或觸電。聯絡服務中心進行檢查、校準
或維修。
••如發生任何下列情況,即時切斷產品電源並聯
絡當地服務中心。
-- 產品曾受損毀
-- 產品曾被異物進入
-- 產品曾產生煙霧或不尋常氣味
••可能導致火災或觸電。
••若長時間不使用產品,請拔除產品電源線。
灰塵覆蓋可導致火災,或絕緣層受損可導致漏
電、觸電或火災。
••不可將產品暴露於滴水或水環境下;不可於產
品上放置任何裝有液體的物件,例如花瓶 。
••如牆壁會暴露於油或油霧,請勿在上面安裝
此產品。此舉可能會損壞產品,並導致產品
掉落。
••如水或其他物質進入了產品(如 AC 充電器、
電源線、電視機),請中斷連接電源線並馬上
聯絡服務中心。
否則,可能導致火災或觸電。
••僅可使用經 LG Electronics 認可的 AC 適配器和
電源線。否則,可能導致火災、觸電、產品無
法正常運作或變形。
••切勿拆開 AC 適配器或電源線。可能導致火災
或觸電。
••請小心處理適配器避免掉落或被撞擊遭到撞擊
可能會對產品造成損害。
••確保電源線穩固地連接到電視的電源插頭。
••將產品安裝於不存在無線電波的地方。
••請於電源線及天線間預留足夠空間以防止當天
線掉落時觸及電源線。此將可能導致觸電。
••請勿將產品安裝於不穩固的層架或斜面上。亦
應避免將產品放置於震動或不能安全承托產品
的位置。否則,可能因產品跌落或翻倒而導致
受傷或產品損壞。
••如將電視安裝於底座上,請採取措施以預防
產品翻倒。否則,將可能導致電視翻倒並引
致受傷。
••如希望將產品安裝於牆上,請於產品背面安裝
VESA 標 準掛牆介面(選購配件)。於安裝套
件以使用掛牆架(選購配件)時請注意固定以
防墜落。
••只使用製造商指定的附件/配件。
••於安裝天線時請諮詢認可技師。此可能引起火
災或觸電危險。
3
粵語
••當裝置連接到交流電入牆插座,即使以開關關
閉裝置,也不會與交流電源斷開。
••於拔除電源插頭時,抓緊插頭以將其拔除。
••如電源線內的金屬線脫離將可能引致火災。
••於移動產品時,確保先將電源關閉。然後,拔
除電源線、天線纜線及所有連接纜線。
電視組合或電源線有可能受損並因此引發火災
或觸電可能。
••當移動產品或移除產品包裝時因產品重量需二
人同時進行。否則可能導致受傷。
••向合資格服務人員諮詢所有有關維修事宜。當
產品 受到任何形式的損壞時,例如電源線或插
頭損壞,液 體濺入或物件落入裝置中,裝置暴
露於雨水或潮濕環境,裝置不能正常工作,或
裝置掉落摔壞,均需進行維修服務。
••請勿在電視旁使用高壓電器 (例如, 電蚊拍)。
這可能引起產品故障。
••請於清洗產品及其組件時先拔除電源並以軟布
拭擦。使用力度過大將可能導致磨損或褪色。
請勿以水噴灑或以濕布拭刷。請勿使用會對產
品及其屏幕造成損壞的化學品,例如玻璃清潔
劑、空氣清新劑、殺蟲劑、潤滑劑、汽車或工
業用蠟劑、磨光劑、稀釋劑、苯、酒精等。否
則,將可能導致火災、觸電或產品損壞(變
形、腐蝕或破裂)。
警告!
請勿將電視機置於搖晃不穩的位置,因爲電視機
可能會掉落並導致嚴重個人傷害及傷亡。只要採
取下列預防工作便可避免傷害事故發生(特別是
兒童傷害):
••使用製造商建議的儲存櫃及支架置放電視。
••只選用可安全支撐電視機的家具。
••確保電視機不會懸在支撐家具的邊沿。
••切勿將電視機置放在家具高處(如櫥櫃或書
架),除非以適當的支撐物固定家具和電。
••電視機和支撐家具之間不要夾置布料或其他
材料。
••告訴兒童爬上家具觸碰電視機或其控制器的
危險性。
如要收藏並將電視機置放於其他地方,建議一律
採用上述建議。
4
符號
AC 代表交流電。
DC 代表直流電。
代表第二級設備。
代表待機。
代表「開啟」(電源)。
代表危險電壓。
準備使用
••如電視從廠商運出後首次開啟,電視初始化可
能需時數分鐘。
••插圖可能與實際情況有差異。
••您電視的 OSD(螢幕顯示)可能與此手冊中顯
示的內容略有不同。
••可用的功能表及選項可能與您使用的輸入來源
或產品型號有所不同。
••新功能或將添加至此電視。
••產品隨附的部件視乎型號而可能有所不同。
••本手冊的產品規格或內容或會因產品功能升級
而隨時變更,恕不另行通知。
••為了獲得最好的連接效果,HDMI 纜線和 USB
裝置接頭厚度應少於 10 毫米,寬度應少於 18
毫米。如果 USB 纜線或 USB 記憶卡與您的電
視的 USB 端口尺寸不符,請使用支援 USB 2.0
的延長線。
B
B
A
A
*A ≤ 10 毫米
*B ≤ 18 毫米
••使用附有 HDMI 標誌的獲認證的纜線。
••如您並非使用獲認證的纜線,可能無法於螢幕
顯示畫面,或發生連接錯誤。
••建議的 HDMI 纜線類型 (3m 或以下)
-- 高速 HDMI®/TM 纜線
-- 設有 Ethernet 的高速 HDMI®/TM 纜線
抬起與移動電視
不論任何類型及大小,抬起或移動電視時,請閱
讀下文,確保安全搬運,以防電視刮花或受損。
••建議以包裝箱或連同電視原有的包裝材料移
動電視。
••移動或抬起電視前,中斷電源線和所有纜線
的連接。
••當握住電視時螢幕應面向外側以避免損壞。
粵語
••請勿使用任何未經批准部件,以確保
安全和產品壽命。
••因使用未經批准物品而造成的任何損
壞或傷害並不包括在保修範圍內。
••某些型號的屏幕上,像有一層薄膜。
它實際上是屏幕的一部分,請勿移
除。
••將底座安裝至電視組合時,電視螢幕
應面向下方並放於附有軟墊的枱面或
平面上以避免螢幕磨損。
••確保螺絲已完全扭緊。(如果沒有穩
固扭緊螺絲,電視在安裝後可能會向
前傾斜。)請勿過份用力及過度扭緊
螺絲,否則螺絲可能會受損並無法正
確上緊。
••確保擰乾布上多餘的水分及清潔劑。
••切勿直接在電視螢幕上噴水或清潔
劑。
••請只在乾布上噴上適度的水或清潔劑
以擦拭螢幕。
••握穩電視的頂部和底部。確保不要握住透明部
分、喇叭或喇叭排孔區域。
另外購買
另購項目可因改善品質而隨時變更或修改,恕不
另行通知。如要購買這些項目,請聯絡經銷商。
這些裝置僅配合某些型號使用。
此等裝置的名稱和設計會因功能更新,出廠情況
或政策而有所改變 。
(視乎型號而定)
AN-MR600
AN-VC550
神奇遙控器
智能攝影機
••大型電視需最少二人共同運送。
••使用人手搬運電視時,請根據以下圖示握住
電視。
••搬運電視時,請勿搖動或令電視受過度震動。
••搬運電視時,保持電視直立,切勿轉向電視的
側面,或向左方或右方傾斜電視。
••請勿過份用力,否則可能導致外框底座屈曲 /
折彎,會損壞螢幕。
••操作電視時,請勿損壞凸起的按鈕。
••避免時常點按畫面,否則會導致畫面
受損。
••請勿握住纜線整理器移動電視,因其
可能斷裂而導致受傷及電視損壞。
5
粵語
使用按鈕
安裝到桌面
只需使用按鈕,即可輕鬆操作電視功能。
1 將電視機抬起並擺放在桌子上,保持機身豎
直。
-- 與牆壁保留最少 10 厘米空間以保持空氣流
通。
10 厘米
米
10 厘
10 厘米
10 厘米
10 厘米
2 將電源線連接至牆上電源插座。
基本功能
開機(按一下)
關機(按住)1
調校音量
調校節目
1 所有操作中的應用程式將會關閉,令正在進行
的所有錄影將會停止。
••請勿將電視置於發熱源附近,因此可
能引發火災或其他損害。
••在組裝產品時,請勿於螺絲零件處使
用油或潤滑劑等外來物質。(這樣可能
會導致產品損壞。)
安全地將電視安裝到牆壁上
(此功能不是所有型號都適用)
調整功能表
當電視開啟時,按一下 按鈕。
您可使用按鈕以調整功能表項目。
關閉電源。
清除所有畫面顯示並返回電視檢視。
改更輸入來源。
進入設定目錄。
1 在電視背面插入並擰緊環首螺絲或 固定片和
螺絲。
-- 如果在環首螺絲位置中插入了螺絲,請先將
這些螺絲取出。
2 用螺絲將固定片安裝到牆上。
將掛牆架的位置對準電視背面的環形螺絲。
3 以堅固繩索將環形螺絲及掛牆架連接。確保繩
索與平面保持水平。
••確保孩童不要攀附於電視上。
••使用堅固平臺或矮櫃以穩固承托電視。
••掛牆架、螺絲及繩索需另行購買。您可從本地
經銷商取得其他配件。
6
連線(注意事項)
將選購的掛牆架小心安裝在電視後方,再將掛牆
架安裝在與地面垂直的堅固牆壁上。將電視安裝
在其他建築物料時,請聯絡合資格的人員。LG
建議應由合資格的專業安裝人員進行掛牆安裝。
建議使用 LG 掛牆架。LG 掛牆架調整容易,連接
纜線亦非常方便。如不使用 LG 掛牆架,請使用
能將裝置穩固於牆上並有足夠空間連接外部裝
置的掛牆架。如使用無法調整的支架,請將支
架掛牆。先將纜線連接至電視,再將電視放到
支架上。
將不同的外置裝置連接至電視,並切換輸入模式
以選取外置裝置。有關外置裝置連接的詳情,請
參閱個別裝置隨附的手冊。
可用的外置裝置為:HD 接收器、DVD 播放
器、VCR、音效系統、USB 儲存裝置、電腦、遊
戲裝置及其他外置裝置。
••外置裝置連接視乎型號而有所不同。
••不論電視連接埠順序為何,連接外部裝置至
電視。
••如果您在 DVD 錄影機或 VCR 錄製電視節目,
請確保電視訊號輸入纜線已連接電視及DVD 錄
影機或 VCR。有關錄影的詳情,請參閱連接裝
置隨附的手冊。
••有關操作說明,請參閱外部裝置手冊。
••如果您將遊戲裝置連接至電視,使用遊戲裝置
隨附的纜線。
••於電腦模式,可能產生由解像度、垂直格式、
對比度或亮度引致的雜音。如出現雜訊,將電
腦輸出變更為其他解像度或將刷新率變更為其
他頻率、或於 影像 功能表中調整亮度和對比
度,直至影像變為清晰。
••於電腦模式,部份解像度設定可能未能正常運
作,視乎顯示卡而定。
••某些 USB 集線器可能不能運作。如連接至 USB
集線器的 USB 裝置未能被探測,可直接將裝置
連接至於電視上的 USB 端口。
••建議使用CAT 7 網絡線連接區域網絡(LAN)。
10 厘米
10 厘米
10 厘米
10 厘米
確保使用符合 VESA 標準的螺絲及掛牆底座托
架。掛牆底座套件的標準尺寸如下表所述。
另外購買(掛牆架)
型號
VESA (A x B)
標準螺絲
螺絲數目
掛牆架
55EG9A7*
300 x 200
M6
4
OTW420B
A
B
••將電視安裝於掛牆架前需反方向轉動
底座以將之移除。
粵語
安裝在牆上
天線連接
使用 RF 線 (75 Ω) 將電視連接至牆壁天線插座。
••如使用兩部電視以上,使用訊號分線器。
••如畫面品質惡劣,正確安裝訊號放大器以改善
圖像品質。
••如有連接天線,但畫面品質惡劣,嘗試以正確
方向重新對準天線。
••天線及轉換器並不提供。
••支援的數碼電視音效:MPEG、Dolby
Digital、Dolby Digital Plus、HE-AAC
其他連接
將電視連接至外部裝置。為達到最佳圖片及音
訊質素,請使用 HDMI 纜線將外置裝置及電視連
接。不提供部份獨立纜線。
••支援的 HDMI 音效格式:
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),
DTS (44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz,48 kHz,96 kHz,192 kHz)
(視乎型號而定)
7
神奇遙控器
粵語
(因應產品型號或地區,部分按鈕功能和服務可
能無法提供。)
當顯示“神奇遙控器電池電量低,請更換電池。”
的訊息時,請更換電池。
如需安裝電池,打開電池蓋,更換電池 (1.5 V
AA) 時配對電池格內的 及 端標籤,然後關
上電池蓋。確保將遙控器指向電視機上的神奇
遙控器感應器。如要移除電池,以相反步驟執
行動作。
••在某些國家或收看模擬廣播時,部份
按鍵可能無法使用。
B
A
(電源) 開啟或關閉電視。
(輸入) 改更輸入來源。
-- 按住 (輸入) 按鈕將顯示功能表,讓您選取
已連接至電視的外部裝置。
數字鍵 輸入數字
進入已儲存節目列表。
(空間) 打開屏幕鍵盤上的一個空的空間。
檢視目前節目及畫面的資訊。
8
調整音量。
(靜音) 打開或關閉聲音。
* 將啟用音效說明功能。
捲動已儲存的節目。
(主頁) 進用功能表。
(返回) 返回至上一層。
清除所有畫面顯示並返回電視檢視。
滾輪(確認) 按下滾輪按鈕的中央以選擇功
能表。您可使用滾輪鍵轉台。
導航按鍵 (上/下/左/右) 按上、下、
左或右按鈕以捲動 功能表。如您按下
按鈕時同時使用游標,游標將於螢幕消失,神奇
遙控器將以一般遙控器運作。如要再次於螢幕上
顯示游標,向左及右搖一搖神奇遙控器。
顯示節目指南。
(螢幕遙控) 顯示螢幕遙控。
-- 存取通用控制功能表。
使用於觀看 3D 影片。(只限 3D 型號)
*要使用按鈕,請按住超過 3 秒。
註冊神奇遙控器
如何註冊神奇遙控器
如要使用神奇遙控器,首先與電視進行配對。
1 將電池放入神奇遙控器並開啟電視。
2 將神奇遙控器指向電視,然後按遙控器上的
滾輪(確認)。
-- 如電視無法註冊神奇遙控器,請關閉電視然
後重新開啟,再試一次。
如何使用神奇遙控器
••輕輕向右或左搖一搖神奇遙控器,或按下
(主頁),
(輸入), 按鈕可令游標於螢
幕上顯示。
(對某些電視型號而言,遊標會在您轉動
滾輪 (確認)按鈕後顯示。)
••如於一段時間內沒有使用游標或將神奇遙控器
放於平面上,游標便會消失。
••如果游標無法順暢反應,您可以將游標移至螢
幕邊緣以重新設定。
••由於擁有額外功能,神奇遙控器比普通遙控器
更快耗盡電池。
粵語
(語音辨識)
使用語音辨識功能時需要網絡連接。
1 按下語音辨識按鈕。
2 在語音顯示視窗顯示於電視螢幕時說話。
-- 請於距離臉部不超過 10 厘米的情況下使用神
奇遙控器。
-- 如果說話速度過快或過慢,可能無法進行語
音辨識。
-- 辨識率可能視乎用戶的特徵(聲音、發音、
語調和速度)及環境(噪音和電視音量)而
有所不同。
(快速設定) 進入快速設定。
-- 按住 (快速設定) 按鈕顯示 進階設定 菜
單。
,
,
,
訪問某些選單中的特殊功能。
電視文字按鍵(
,
) 此等按鍵用於電視文
字廣播。
在數碼模式調用所需字幕。
使用神奇遙控器時的注意事項
••於指定的距離使用遙控器(10 米以內)。
如於指定範圍以外使用遙控器或指定範圍內有
障礙物時,可能會出現通訊故障。
••取決於配件而定,可能會出現通訊故障。
裝置如微波爐及與有相同頻率波段(2.4 GHz)
的無線 LAN 設備(例如神奇遙控器)。可導致
通訊故障。
••若無線路由器(AP)與電視相距 1 米以內,神
奇遙控器可能可能無法正常運作。
您的無線路由器應距離電視多於 1 米。
••不要拆解電池或使其過熱。
••避免電池掉落。防止電池遭受極端撞擊。
••以錯誤的方向插入電池可能造成爆炸。
如何註銷神奇遙控器
同時按住 (返回) 及
(主頁) 按鈕 5 秒,以取
消神奇遙控器與電視的配對。
-- 按住按
鈕將讓您取消並立即重新註冊神
奇遙控器。
9
粵語
授權
疑難排解
受支援的授權因型號而有所不同。更多有關授權
的詳細資料,請瀏覽 www.lg.com。
••無法使用遙控器控制電視。
-- 請檢查產品上的遙控器感應器,然後再試一
次。
-- 請檢查產品和遙控器之間是否有任何障礙
物。
-- 請檢查電池是否仍可使用,且已正確安裝(
對 , 對 )。
••沒有畫面顯示或沒有聲音。
-- 請檢查產品是否已開機。
-- 請檢查電線是否已連接至牆上插頭。
-- 請連接其他產品,確認牆上插頭是否有問
題。
••電視突然關機。
-- 檢查電源控制設定。電源供應可能中斷。
-- 在定時設定中檢查 睡眠時間設定 或 定時器
電源關閉 是否已啟動。
-- 如果在電視開機時沒有訊號,15 分鐘後若無
任何動作,電視就會自動關機。
••連接至電腦 (HDMI) 時顯示 無訊號 或 無效的
格式。
-- 使用遙控器關閉/開啟電視。
-- 重新連接 HDMI 纜線。
-- 在開啟電視的情況下重新啟動電腦。
注意:開放來源程式碼軟件
異常顯示情況
若要獲取此產品所包含的 GPL、LGPL、MPL 來
源程式碼和其他開放來源程式碼認證,請瀏覽
http://opensource.lge.com。
除了來源程式碼,所有涉及到的授權條款、免責
聲明和版權聲明可供下載。
LG Electronics 亦可以透過收費 CD-ROM 提供
開放來源程式碼,費用包括 CD-ROM 成本 (
例如媒體成本、運費以及處理費),您可透過
opensource@lge.com 索取。此服務由購買產品
日期起計算三年內有效。
外置控制裝置設置
(視乎型號而定)
要獲取有關外置控制裝置的設定資訊,請瀏覽
www.lg.com。
10
••如接觸產品時感覺冰冷,於開啟時可能出現「
跳線」情況。此為正常情況,產品並無異常。
••本螢幕面板是擁有數百萬像素的先進產品。
微細黑點及/或高亮彩色光點(紅色、藍或綠
色)可能以每百萬分一 單位出現於顯示面板
上。此並不代表非正常運作及並不影響產品之
性能及其可靠性。
此現象亦會於第三方產品出現並不接受更換
或退款。
••於不同位置(左/右/上/下方)觀看時可能感
受到面板不同亮度及顏色顯示。
此現象的出現乃顯示面板的特性。此與產品性
能無關,並其運作正常。
••長時間顯示靜態圖像可能會引致殘像。請避免
長時間在電視螢幕顯示固定畫面。
產生聲音
••「咔嚦」斷裂雜音:於觀看或關閉電視時出現的
斷裂雜聲乃因溫度與濕度而導致塑料的熱收
縮所產生。此等雜聲於遇熱膨脹之產品較為
常見。
••電路嗡聲/面板訊噪:低水平雜音乃由高速切
換電路以產生大量電流令產品運作時發出。其
因應產品會有所不同。
雜音之產生並不影響產品的性能及可靠性。
規格
數碼訊號
無線模組規格
••由於每個國家的波段頻道有所不同,用戶無法
更改或調整操作頻率。本產品配置之頻率為區
域頻率表內。
••為用戶着想,建議本裝置安裝及使用時,應最
少離用戶身體 20 厘米。
電視制式
DTMB
節目範圍
DTMB :
21~69
外置天線
抗阻
粵語
••能源標籤上標明的每年能源消耗是根據 IEC
62087 及香港能源效益標籤計劃 (EELS) 來計算
(根據不同的型號而定)。
••實際的能源消耗取決於使用環境(觀看的內
容、電視設定等)而定。
類比訊號
PAL D/K, PAL I, NTSC
M
PAL D/K: VHF/UHF
1~69, CATV 1~47
PAL I: VHF/UHF
1~69, CATV 1~47
NTSC M: VHF/UHF
2~78, CATV 1~71
75 Ω
無線 LAN 模組(LGSBW41)規格
無線 LAN
標準
頻率範圍
輸出功率(最大)
IEEE802.11a/b/g/n
2400 轉 2483.5 MHz
5150 轉 5250 MHz
5725 轉 5850 MHz
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4 GHz: 16 dBm
802.11n - 5GHz: 16 dBm
Bluetooth
標準
頻率範圍
輸出功率(最大)
環境條件
Bluetooth
2400 轉 2483.5 MHz
10 dBm 或更低功率
操作溫度
操作濕度
儲存溫度
儲存濕度
0 °C 至 40 °C
低於 80 %
-20 °C 至 60 °C
低於 85 %
11
記下電視的型號和序列號。
參考後蓋上的標籤,當您要求任何服務時將此資
訊告之經銷商。
型號
序號
Safety and Reference
Please read this manual carefully before operating your TV and
retain it for future reference.
www.lg.com
Printed in Korea
Copyright © 2017 LG Electronics Inc. All Rights Reserved.
Warning! Safety instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ENGLISH
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
•• Clean only with dry cloth. Do not place the TV and/or remote
control in the following environments:
-- A location exposed to direct sunlight
-- An area with high humidity such as a bathroom
-- Near any heat source such as stoves and other devices that
produce heat
-- Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
-- An area exposed to rain or wind
-- Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or
product deformation.
•• Do not place the product where it might be exposed to dust. This
may cause a fire hazard.
•• Mains Plug is the TV connecting/disconnecting device to AC
mains electric supply. This plug must remain readily attached and
operable when TV is in use.
•• Do not touch the power plug with wet hands. Additionally, if the
cord pin is wet or covered with dust, dry the power plug completely
or wipe dust off. You may be electrocuted due to excess moisture.
•• Make sure to connect Mains cable to compliant AC mains socket
with Grounded earth pin. (Except for devices which are not
grounded on earth.) Otherwise possibility you may be electrocuted
or injured.
•• Insert power cable plug completely into wall socket otherwise if
not secured completely into socket, fire ignition may break out.
2
•• Ensure the power cord does not come into contact with hot objects
such as a heater. This may cause a fire or an electric shock hazard.
•• Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
•• Bend antenna cable between inside and outside building to
prevent rain from flowing in. This may cause water damaged inside
the Product and could give an electric shock.
•• When mounting TV onto wall make sure to neatly install and
isolate cabling from rear of TV as to not create possibility of electric
shock / fire hazard.
•• Do not plug too many electrical devices into a single multiple
electrical outlet. Otherwise, this may result in fire due to overheating.
•• Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the
product.
•• Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed.
If swallowed by mistake, force the patient to vomit and visit the
nearest hospital. Additionally, vinyl packing can cause suffocation.
Keep it out of the reach of children.
•• Do not let your children climb or cling onto the TV. Otherwise, the
TV may fall over, which may cause serious injury.
•• Dispose of used batteries carefully to ensure that a small child
does not consume them. Please seek Doctor- Medical Attention
immediately if child consumes batteries.
•• Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) between power cable plug and Wall Socket.
Additionally, do not touch the power cable right after plugging into
the wall. You may be electrocuted.
•• Do not put or store inflammable substances near the product.
There is a danger of combustion/explosion or fire due to careless
handling of the inflammable substances.
•• Do not drop metallic objects such as coins, hair pins, chopsticks
or wire into the product, or inflammable objects such as paper
and matches. Children must pay particular attention. Electrical
shock, fire or injury can occur. If a foreign object is dropped into the
product, unplug the power cord and contact the service centre.
•• Do not spray water on the product or scrub with an inflammable
substance (thinner or benzene). Fire or electric shock accident can
occur.
•• Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or
the product can be damaged.
•• Never touch this product or antenna during a thunder or lighting
storm. You may be electrocuted.
•• Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a fire or a burn by a spark.
•• We recommend that you maintain a distance of at least 2 to 7
times the diagonal screen size when watching TV. If you watch TV
for a long period of time, this may cause blurred vision.
•• Only use the specified type of battery. This could cause damage to
the remote control.
•• Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
•• Batteries should not be exposed to excessive heat. For example,
keep away from direct Sunlight, open fireplace and electric heaters.
•• Signal from Remote Control can be interrupted due to external/
internal lighting eg Sunlight, fluorescent lighting. If this occurs turn
off lighting or darken viewing area.
•• When connecting external devices such as video game consoles,
make sure the connecting cables are long enough. Otherwise,
the product may fall over, which may cause injury or damage the
product.
•• Do not turn the product On/Off by plugging-in or unplugging
the power plug to the wall outlet. (Do not use the power plug for
switch.) It may cause mechanical failure or could give an electric
shock.
•• Please follow the installation instructions below to prevent the
product from overheating.
-- The distance between the product and the wall should be more
than 10 cm.
-- Do not install the product in a place with no ventilation (e.g., on
a bookshelf or in a cupboard).
-- Do not install the product on a carpet or cushion.
-- Make sure the air vent is not blocked by a tablecloth or curtain.
This may result in fire.
•• Take care not to touch the ventilation openings when watching the
TV for long periods as the ventilation openings may become hot.
This does not affect the operation or performance of the product.
•• Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with
an exact replacement part by an authorized servicer.
•• Prevent dust collecting on the power plug pins or outlet. This may
cause a fire hazard.
•• Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon.
Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
•• Do not press strongly upon the panel with a hand or sharp object
such as nail, pencil or pen, or make a scratch on it, as it may cause
damage to screen.
•• Avoid touching the screen or holding your finger(s) against it for
long periods of time. Doing so may produce some temporary or
permanent distortion/damage to screen.
ENGLISH
•• Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur. Contact the
service centre for check, calibration or repair.
•• If any of the following occur, unplug the product immediately and
contact your local service centre.
-- The product has been damaged
-- Foreign objects have entered the product
-- The product produced smoke or a strange smell
•• This may result in fire or electric shock.
•• Unplug the TV from AC mains wall socket if you do not intend to
use the TV for a long period of time. Accumulated dust can cause
fire hazard and insulation deterioration can cause electric leakage/
shock/fire.
•• Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus.
•• Do not install this product on a wall if it could be exposed to oil or
oil mist. This may damage the product and cause it to fall.
•• If water or another substance enters the product (like a AC adapter,
power cord, TV), disconnect the power cord and contact the service
centre immediately.
Otherwise, this may result in fire or electric shock.
•• Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction or product deformation.
•• Never Disassemble the AC adapter or power cord. This may result in
fire or electric shock.
•• Handle the adapter carefully to avoid dropping or striking it. An
impact could damage the adapter.
•• Make sure the power cord is connected securely to the power plug
on the TV.
•• Install the product where no radio wave occurs.
•• There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when
the antenna falls. This may cause an electric shock.
•• Do not install the product on places such as unstable shelves or
inclined surfaces. Also avoid places where there is vibration or
where the product cannot be fully supported. Otherwise, the
product may fall or flip over, which may cause injury or damage to
the product.
•• If you install the TV on a stand, you need to take actions to prevent
the product from overturning. Otherwise, the product may fall
over, which may cause injury.
•• If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product.
When you install the set to use the wall mounting bracket
(optional parts), fix it carefully so as not to drop.
•• Only use the attachments / accessories specified by the
manufacturer.
•• When installing the antenna, consult with a qualified service
technician. If not installed by a qualified technician, this may create
a fire hazard or an electric shock hazard.
3
ENGLISH
•• As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this
unit by SWITCH.
•• When unplugging the cable, grab the plug and unplug it, by
pulling at the plug.
•• Don’t pull at the cord to unplug the power cord from the power
board, as this could be hazardous.
•• When moving the product, make sure you turn the power off first.
Then, unplug the power cables, antenna cables and all connecting
cables.
The TV set or power cord may be damaged, which may create a fire
hazard or cause electric shock.
•• When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
•• Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
•• Do not use high voltage electrical goods near the TV(e.g. electric
mosquito-swatter). This may result in product malfunction.
•• When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may
cause scratches or discolouration. Do not spray with water or wipe
with a wet cloth. Do not clean your TV with chemicals including
glass cleaner, any type of air freshener, insecticide, lubricants, wax
(car, industrial), abrasive, thinner, benzene, alcohol etc., which can
damage the product and/ or its panel. Otherwise, this may result
in fire, electric shock or product damage (deformation, corrosion
or breakage).
WARNING!
Never place a television set in an unstable location. A television set
may fall, causing serious personal injury or death. Many injuries,
particularly to children, can be avoided by taking simple precautions
such as:
•• Using cabinets or stands recommended by the manufacturer of the
television set.
•• Only using furniture that can safely support the television set.
•• Ensuring the television set is not overhanging the edge of the
supporting furniture.
•• Not placing the television set on tall furniture (for example,
cupboards or bookcases) without anchoring both the furniture and
the television set to a suitable support.
•• Not placing the television set on cloth or other materials that may
be located between the television set and supporting furniture.
•• Educating children about the dangers of climbing on furniture to
reach the television set or its controls.
If your existing television set is being retained and relocated, the
same considerations as above should be applied.
4
Symbols
Refers to alternating current(AC).
Refers to direct current(DC).
Refers to class II equipment.
Refers to stand-by.
Refer to “ON” (power).
Refers to dangerous voltage.
Preparing
•• If the TV is turned on for the first time after it was shipped from the
factory, initialization of the TV may take a few minutes.
•• Image shown may differ from your TV.
•• Your TV’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
•• The available menus and options may differ from the input source
or product model that you are using.
•• New features may be added to this TV in the future.
•• The items supplied with your product may vary depending on the
model.
•• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
•• For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
B
B
A
A
*A ≤ 10 mm
*B ≤ 18 mm
•• Use a certified cable with the HDMI logo attached.
•• If you do not use a certified HDMI cable, the screen may not display
or a connection error may occur.
•• Recommended HDMI Cable Types (3m or less)
-- High-Speed HDMI®/TM cable
-- High-Speed HDMI ®/TM cable with Ethernet
Lifting and moving the TV
Please note the following advice to prevent the TV from being
scratched or damaged and for safe transportation regardless of its
type and size.
•• It is recommended to move the TV in the box or packing material
that the TV originally came in.
•• Before moving or lifting the TV, disconnect the power cord and all
cables.
•• When holding the TV, the screen should face away from you to
avoid damage.
ENGLISH
•• Do not use any unapproved items to ensure the safety
and product’s lifespan.
•• Any damages or injuries by using unapproved items are
not covered by the warranty.
•• Some models appear to have a thin film on the screen.
It is actually part of the screen; do not remove it.
•• When attaching the stand to the TV set, place the
screen facing down on a cushioned table or flat surface
to protect the screen from scratches.
•• Make sure that the screws are fastened completely. (If
they are not fastened securely enough, the TV may tilt
forward after being installed.) Do not use too much
force and over tighten the screws; otherwise screw may
be damaged and not tighten correctly.
•• Make sure to wring any excess water or cleaner from
the cloth.
•• Do not spray water or cleaner directly onto the TV
screen.
•• Make sure to spray just enough of water or cleaner onto
a dry cloth to wipe the screen.
•• Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
Separate purchase
Separate purchase items can be changed or modified for quality
improvement without any notification. Contact your dealer to buy
these items. These devices only work with certain models.
The model name or design may be changed depending on the
upgrade of product functions, manufacturer’s circumstances or
policies.
(Depending on model)
AN-MR600
AN-VC550
Magic Remote
Smart Camera
•• When transporting a large TV, there should be at least 2 people.
•• When transporting the TV by hand, hold the TV as shown in the
following illustration.
•• When transporting the TV, do not expose the TV to jolts or excessive
vibration.
•• When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
•• Do not apply excessive pressure to cause flexing /bending of frame
chassis as it may damage screen.
•• When handling the TV, be careful not to damage the protruding
buttons.
•• Avoid touching the screen at all times, as this may
result in damage to the screen.
•• Do not move the TV by holding the cable holders, as the
cable holders may break, and injuries and damage to
the TV may occur.
5
Using the button
Mounting on a table
You can simply operate the TV functions, using the button.
1 Lift and tilt the TV into its upright position on a table.
-- Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
10 cm
10 cm
ENGLISH
10 cm
10 cm
2 Connect the power cord to a wall outlet.
Basic Functions
Power On (Press)
Power Off (Press and hold)1
Volume Control
Programmes Control
•• Do not place the TV near or on sources of heat, as this
may result in fire or other damage.
•• Do not apply foreign substances (oils, lubricants, etc.)
to the screw parts when assembling the product.
(Doing so may damage the product.)
Securing the TV to a wall
(This feature is not available for all models.)
1 All running apps will close, and any recording in progress will stop.
Adjusting the Menu
When the TV is turned on, press the button one time.
You can adjust the Menu items using the buttons.
Turns the power off.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Accesses the setting menu.
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the
back of the TV.
-- If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the
rear of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy
rope. Make sure to keep the rope horizontal with the flat surface.
•• Make sure that children do not climb on or hang on
the TV.
•• Use a platform or cabinet that is strong and large enough to
support the TV securely.
•• Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
6
Connections (notifications)
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the
use of LG’s wall mount bracket. The LG wall mount is easy to adjust or
to connect the cables. When you do not use LG’s wall mount bracket,
please use a wall mount bracket where the device is adequately
secured to the wall with enough space to allow connectivity to
external devices. If you are using a non-adjustable mount, attach the
mount to the wall. Attach the cables to the TV first, then attach the
TV to the mount.
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
•• The external device connection may differ from the model.
•• Connect external devices to the TV regardless of the order of the
TV port.
•• If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
•• Refer to the external equipment’s manual for operating
instructions.
•• If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
•• In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change
the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the Picture
menu until the picture is clear.
•• In PC mode, some resolution settings may not work properly
depending on the graphics card.
•• Some USB Hubs may not work. If a USB device connected using
a USB Hub is not detected, connect it to the USB port on the TV
directly.
•• When connecting via a wired LAN, it is recommended to use a CAT
7 cable.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described
in the following table.
Separate purchase (Wall mounting bracket)
Model
VESA (A x B)
Standard screw
Number of screws
Wall mount bracket
55EG9A7*
300 x 200
M6
4
OTW420B
A
B
•• Remove the stand before installing the TV on a wall
mount by performing the stand attachment in reverse.
ENGLISH
Mounting on a wall
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
•• Use a signal splitter to use more than 2 TVs.
•• If the image quality is poor, install a signal amplifier properly to
improve the image quality.
•• If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
•• An antenna cable and converter are not supplied.
•• Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
•• Supported HDMI Audio format:
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),
DTS (44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz,48 kHz,96 kHz,192 kHz)
(Depending on model)
7
Magic remote functions
ENGLISH
(Some buttons and services may not be provided depending on
models or regions.)
When the message “Magic remote battery is low. Change the battery.”
is displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries
(1.5 V AA) matching the and ends to the label inside the
compartment, and close the battery cover. Be sure to point the magic
remote toward the remote control sensor on the TV. To remove the
batteries, perform the installation actions in reverse.
•• In Analogue TV and some countries, some remote
control buttons may not work.
B
A
(POWER) Turns the TV on or off.
(INPUT) Changes the input source.
-- Pressing and holding the (INPUT) button displays all the
lists of external inputs.
Number buttons Enters numbers.
Accesses the saved programmes list.
(Space) Opens an empty space on the screen keyboard.
Views the information of the current programmes and screen.
8
Adjusts the volume level.
(MUTE) Mutes all sounds.
* Audio descriptions function will be enabled.
Scrolls through the saved programmes.
(HOME) Accesses the Home menu.
(BACK) Returns to the previous screen.
Clears on-screen displays and returns to last input viewing.
Wheel (OK) Press the center of the Wheel button to select a
menu. You can change programmes by using the Wheel button.
Navigation buttons (up/down/left/right) Press
the up, down, left or right button to scroll the menu. If you press
buttons while the pointer is in use, the pointer will
disappear from the screen and Magic Remote will operate like a
general remote control. To display the pointer on the screen again,
shake Magic Remote to the left and right.
Shows programmes guide.
(Screen remote) Displays the Screen Remote.
-- Accesses the Universal Control Menu.
Used for viewing 3D video. (Only 3D models)
* To use the button, press and hold for more than 3 seconds.
Registering magic remote
How to register the magic remote
To use the Magic Remote, first pair it with your TV.
1 Put batteries into the Magic Remote and turn the TV on.
2 Point the Magic Remote at your TV and press the Wheel (OK)
on the remote control.
-- If the TV fails to register the Magic Remote, try again after
turning the TV off and back on.
How to use magic remote
•• Shake the Magic Remote slightly to the right and left or press
(HOME), (INPUT),
buttons to make the pointer
appear on the screen.
(In some TV models, the pointer will appear when you turn the
Wheel (OK) button.)
•• If the pointer has not been used for a certain period of time or
Magic Remote is placed on a flat surface, then the pointer will
disappear.
•• If the pointer is not responding smoothly, you can reset the pointer
by moving it to the edge of the screen.
•• The Magic Remote depletes batteries faster than a normal remote
due to the additional features.
Precautions to take when using the magic
remote
ENGLISH
(Voice recognition)
Network connection is required to use the voice recognition function.
1 Press the voice recognition button.
2 Speak when the voice display window appears on the TV screen.
-- Use the Magic Remote no further than 10 cm from your face.
-- The voice recognition may fail when you speak too fast or too
slowly.
-- The recognition rate may vary depending on the user’s
characteristics (voice, pronunciation, intonation, and speed) and
the environment (noise and TV volume).
(Q. Settings) Accesses the Quick Settings.
-- Pressing and holding the (Q. Settings) button displays the
Advanced menu.
, , ,
These access special functions in some menus.
Teletext buttons (
,
) These buttons are used for
teletext.
Recalls your preferred subtitle in digital mode.
•• Use the remote control within the specified range (within 10 m).
You may experience communication failures when using the device
outside the coverage area or if there are obstacles within the
coverage area.
•• You may experience communication failures depending on the
accessories.
Devices such as a microwave oven and wireless LAN operate in the
same frequency band (2.4 GHz) as the Magic Remote. This may
cause communication failures.
•• The Magic Remote may not work properly if a wireless router (AP)
is within 1 meter of the TV.
Your wireless router should be more than 1 m away from the TV.
•• Do not disassemble or heat the battery.
•• Do not drop the battery. Avoid extreme shocks to the battery.
•• Inserting the battery in the wrong way may result in explosion.
How to deregister the magic remote
Press and hold the (BACK) and
(HOME) buttons at the same
time for five seconds, to unpair the Magic Remote with your TV.
-- Pressing and holding the
button will let you cancel and
reregister Magic Remote at once.
9
Troubleshooting
Supported licenses may differ by model. For more information about
licenses, visit www.lg.com.
•• Cannot control the TV with the remote control.
-- Check the remote control sensor on the product and try again.
-- Check if there is any obstacle between the product and the
remote control.
-- Check if the batteries are still working and properly installed (
to , to ).
•• No image display and no sound is produced.
-- Check if the product is turned on.
-- Check if the power cord is connected to a wall outlet.
-- Check if there is a problem in the wall outlet by connecting other
products.
•• The TV turns off suddenly.
-- Check the power control settings. The power supply may be
interrupted.
-- Check if the Sleep Timer / Timer Power Off is activated in the
Timers settings.
-- If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
•• When connecting to the PC (HDMI), No Signal or Invalid Format
is displayed.
-- Turn the TV off/on using the remote control.
-- Reconnect the HDMI cable.
-- Restart the PC with the TV on.
Open source software notice information
Abnormal Display
ENGLISH
Licenses
To obtain the source code under GPL, LGPL, MPL, and other open
source licenses, that is contained in this product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the
date on which you purchased the product.
External control device setup
(Depending on model)
To obtain the external control device setup information, please visit
www.lg.com.
•• If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
•• This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1 ppm on the panel. This does not indicate a
malfunction and does not affect the performance and reliability
of the product.
This phenomenon also occurs in third-party products and is not
subject to exchange or refund.
•• You may find different brightness and color of the panel depending
on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel.
It is not related with the product performance, and it is not
malfunction.
•• Displaying a still image for a prolonged period of time may cause
image sticking. Avoid displaying a fixed image on the TV screen for
a long period of time.
Generated sound
•• “Cracking” noise: A cracking noise that occurs when watching or
turning off the TV is generated by plastic thermal contraction due
to temperature and humidity. This noise is common for products
where thermal deformation is required.
•• Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies a
large amount of current to operate a product. It varies depending
on the product.
This generated sound does not affect the performance and
reliability of the product.
10
Specifications
Digital TV
•• The annual energy consumption indicated on the energy label is
measured in accordance with IEC 62087 and the Hong Kong Energy
Efficiency Labelling Scheme (EELS) (depending on the model).
•• The actual energy consumption depends on the usage environment
(the content watched, TV settings, etc.).
Programme
coverage
External
antenna
impedance
DTMB
DTMB: 21~69
Analogue TV
PAL D/K, PAL I, NTSC M
PAL D/K: VHF/UHF 1~69,
CATV 1~47
PAL I: VHF/UHF 1~69, CATV
1~47
NTSC M: VHF/UHF 2~78,
CATV 1~71
75 Ω
ENGLISH
Wireless module Specification
•• As band channels can vary per country, the user cannot change or
adjust the operating frequency. This product is configured for the
regional frequency table.
•• For consideration of the user, this device should be installed and
operated with a minimum distance of 20 cm between the device
and the body.
Television
system
Wireless module(LGSBW41)Specifications
Wireless LAN
Standard
Frequency range
Output power (Max.)
IEEE802.11a/b/g/n
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4GHz: 16 dBm
802.11n - 5GHz: 16 dBm
Bluetooth
Standard
Frequency range
Output power (Max.)
Environment
condition
Operating
Temperature
Operating
Humidity
Storage
Temperature
Storage
Humidity
Bluetooth
2400 to 2483.5 MHz
10dBm or Lower
0 °C to 40 °C
Less than 80 %
-20 °C to 60 °C
Less than 85 %
11
Record the model number and serial number of the TV.
Refer to the label on the back cover and quote this
information to your dealer when requiring any service.
MODEL
SERIAL
OWNER’S MANUAL
EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
www.lg.com
2
KEY CODES
ENGLISH
ENG
KEY CODES
• This feature is not available for all models.
Code
(Hexa)
Function
Note
Code
(Hexa)
Function
Note
00
CH +, PR +
R/C Button
53
List
R/C Button
01
CH -, PR -
R/C Button
5B
Exit
R/C Button
02
Volume +
R/C Button
60
PIP(AD)
R/C Button
03
Volume -
R/C Button
61
Blue
R/C Button
06
> (Arrow Key / Right Key)
R/C Button
63
Yellow
R/C Button
07
< (Arrow Key / Left Key)
R/C Button
71
Green
R/C Button
08
Power
R/C Button
72
Red
R/C Button
09
Mute
R/C Button
79
Ratio / Aspect Ratio
R/C Button
0B
Input
R/C Button
91
AD (Audio Description)
R/C Button
0E
SLEEP
R/C Button
9E
LIVE MENU
R/C Button
0F
TV, TV/RAD
R/C Button
7A
User Guide
R/C Button
R/C Button
7C
Smart / Home
R/C Button
10 - 19 * Number Key 0 - 9
1A
Q.View / Flashback
R/C Button
7E
SIMPLINK
R/C Button
1E
FAV (Favorite Channel)
R/C Button
8E
►► (Forward)
R/C Button
20
Text (Teletext)
R/C Button
8F
◄◄ (Rewind)
R/C Button
21
T. Opt (Teletext Option)
R/C Button
AA
Info
R/C Button
28
Return (BACK)
R/C Button
AB
Program Guide
R/C Button
30
AV (Audio / Video) Mode
R/C Button
B0
► (Play)
R/C Button
39
Caption/Subtitle
R/C Button
B1
ꕗ (Stop / File List)
R/C Button
40
Λ (Arrow Key / Cursor Up)
R/C Button
B5
RECENT
R/C Button
41
V (Arrow Key / Cursor
Down)
R/C Button
BA
ꕘ (Freeze / Slow Play /
Pause)
R/C Button
42
My Apps
R/C Button
BB
Soccer
R/C Button
43
Menu / Settings
R/C Button
BD
ꔄ (REC)
R/C Button
44
OK / Enter
R/C Button
DC
3D
R/C Button
45
Q.Menu
R/C Button
99
AutoConfig
R/C Button
4C
List, - (ATSC Only)
R/C Button
9F
App / *
R/C Button
4D
PICTURE
R/C Button
9B
TV / PC
R/C Button
52
SOUND
R/C Button
* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
EXTERNAL CONTROL DEVICE SETUP
3
• Image shown may differ from your TV.
Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.
Note: The type of control port on the TV can be different between model series.
* Please be advised that not all models support this type of connectivity.
* Cable is not provided.
USB to Serial converter with USB Cable
USB IN
USB Type
(PC)
(TV)
• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product
ID :IN0x2008) USB to serial converter
RS-232C
(CONTROL & SERVICE)
which is not made nor provided by LG.
• It can be purchased from computer stores that carry accessories for IT support professionals.
(TV)
(PC)
USB IN
RS-232C With RS232C Cable
(PC)
(TV)
SERVICE ONLY
DE9 (D-Sub 9pin) Type
1
• You need to purchase the RS-232C (DE9, D-Sub
3 9pin female-to-female type) to RS-232C cable required
for the connection between the PC and the TV, which is specified in the manual.
(PC)
2
RS-232C IN
(CONTROL & SERVICE)
(PC)
SERVICE ONLY
1
3
RS-232C IN
(CONTROL & SERVICE)
2
(PC)
(TV)
1
3
(PC)
The connection interface may differ from your TV.
(TV)
2
(TV)
(TV)
1
3
(PC)
RS-232C IN
2
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
(CONTROL & SERVICE)
(TV)
ENGLISH
ENG
EXTERNAL CONTROL DEVICE SETUP
USB USB
IN IN
4
EXTERNAL CONTROL DEVICE SETUP
(PC)
(PC)
(TV)
(TV)
RS-232C IN
(CONTROL
SERVICE)
• You need to purchase the phone-jack to RS-232 cable required
for &the
connection between the PC and
the TV, which is specified in the manual.
RS-232C IN
(PC)
(PC)
(CONTROL & SERVICE)
* For other models, connect to the USB port.
* The connection interface may differ from your TV.
1
3
(PC)
(PC)
1
3
2
2
- or
(TV)
(TV)
(TV)
(TV)
1
3
(PC)
(PC)
SERVICE
ONLY ONLY
SERVICE
ENGLISH
ENG
Phone jack Type
1
3
RS-232C IN
(CONTROL & SERVICE)
2
RS-232C IN
(CONTROL & SERVICE)
2
Customer Computer
(TV)
(TV)
RS-232C configurations
3-Wire Configurations(Not standard)
1
5
PC
RXD
RS-232C IN
(CONTROL & SERVICE)
TXD
RS-232C IN
(CONTROL & SERVICE)
GND
6
2
2
TXD
3
1
RXD
5
3
GND
OR
9
RS-232C
(Serial port)
TV
RXD
3
2
TXD
TXD
2
1
RXD
GND
5
3
GND
D-Sub 9
Phone
Set ID
For Set ID number, see "Real Data Mapping" on p.6
1. Press SETTINGS to access the main menus.
2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.
3. Press the Navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
* (Depending on model)
EXTERNAL CONTROL DEVICE SETUP
5
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
ENGLISH
ENG
Communication Parameters
• Stop bit : 1 bit
• Communication code : ASCII code
• Use a crossed (reverse) cable.
Command reference list
(Depending on model)
COMMAND1 COMMAND2
DATA
(Hexadecimal)
01. Power*
k
a
00 to 01
02. Aspect
Ratio
k
c
(p.7)
03. Screen
Mute
k
d
(p.7)
k
e
00 to 01
k
f
00 to 64
06. Contrast
k
g
00 to 64
07.
Brightness
k
h
00 to 64
08. Color/
Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
k
00 to 32
l
00 to 01
m
00 to 01
04. Volume
Mute
05. Volume
Control
10.
k
Sharpness
11. OSD
k
Select
12. Remote
Control Lock k
Mode
13. Treble
k
r
00 to 64
14. Bass
k
s
00 to 64
COMMAND1 COMMAND2
DATA
(Hexadecimal)
15. Balance k
16. Color
(Colour)
x
Temperature
17. ISM
Method (Only j
Plasma TV)
t
00 to 64
u
00 to 64
p
(p.8)
18. Equalizer j
v
(p.8)
q
00 to 05
a
(p.9)
b
00 to 01
19. Energy
j
Saving
20. Tune
m
Command
21. Channel m
(Programme)
Add/Del(Skip)
22. Key
m
c
Key Codes
23. Control
Backlight,
Control Panel
Light
24. Input
select (Main)
25. 3D (Only
3D models)
26. Extended
3D (Only 3D
models)
27. Auto
Configure
m
g
00 to 64
x
b
(p.11)
x
t
(p.11)
x
v
(p.12)
j
u
(p.12)
* Note:During playing or recording media, all commands except Power (ka) and Key (mc) are not
executed and treated as NG.
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
6
EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV.
[Set ID]
:You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set
can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return - ASCII code ‘0x0D’
[ ]
: Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
* When you enter the [data] in hexadecimal, refer to following conversion table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0
01 : Step 1 (Set ID 1)
...
0A : Step 10 (Set ID 10)
...
0F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
...
32 : Step 50 (Set ID 50)
33 : Step 51 (Set ID 51)
...
63 : Step 99 (Set ID 99)
...
C7 : Step 199
C8 : Step 200
...
FE : Step 254
FF : Step 255
...
01 00 : Step 256
...
27 0E : Step 9998
27 0F : Step 9999
...
EXTERNAL CONTROL DEVICE SETUP
7
01.Power (Command: k a)
►► To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]
* Similarly, if other functions transmit ‘FF’ data
based on this format, Acknowledgement feedback
presents status about each function.
02.Aspect Ratio (Command: k c)
(Main Picture Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen 07 : 14:9
(4:3)
(Europe, Colombia, Mid-East,
02 : Wide screen
Asia except South Korea and
(16:9)
Japan)
04 : Zoom
09 : * Just Scan
05 : Zoom 2
0B : Full Wide
(Latin America
(Europe, Colombia, Midexcept Colombia
East, Asia except South
Only)
Korea and Japan)
06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16
Original
0c : 21:9 (Depending on model)
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
04.Volume Mute (Command: k e)
►► To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05.Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06.Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition),
Just Scan is available.
* Full wide mode may work differently based on
model and is supported for DTV fully, and ATV,
AV partially.
07.Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE
menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
03.Screen Mute (Command: k d)
►► To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
* Commands may work differently depending on model and signal.
8
EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
08.Color/Colour (Command: k i)
13. Treble (Command: k r)
►► To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu.
►► To adjust treble.
You can also adjust in the AUDIO menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
09.Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0
0 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model)
14. Bass (Command: k s)
►► To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
10.Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE
menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model)
15.Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
Data Min : 00 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
11.OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
12.Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
When main power is off & on (plug-off and plug-in,
after 20 - 30 seconds), external control lock is
released.
* In the standby mode (DC off by off timer or ‘ka’,
‘mc’ command), and if key lock is on, TV will not
turn on by power on key of IR & Local Key.
16.Color(Colour) Temperature (Command: x u)
►► To adjust colour temperature. You can also adjust
Color(Colour) Temperature in the PICTURE menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17.ISM Method (Command: j p) (Only Plasma TV)
►► To control the ISM method. You can also adjust
ISM Method in OPTION menu.
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data Min : 02: Orbiter
08: Normal
20: Color(Colour) Wash
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
* Analog Antenna/Cable
►► Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
0
[Data 00][Data 01] Channel Data
Data00 : High byte channel data
Data01 : Low byte channel data
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
LSB
0
0
0
0
Frequency
0
0
0
Data 02 : Input Source (Analog)
- 00 : Antenna TV (ATV)
- 80 : Cable TV (CATV)
Data
7
6
5
Frequency
4
3
2
1
0
Step
0
0
0
1st Band
0
0
0
0
0
0(decimal)
0
0
1
2nd Band
0
0
0
0
1
1(decimal)
0
1
0
3rd Band
...
...
...
...
...
...
0
1
1
4th Band
1
0
0
1
1
19(decimal)
1
0
0
5th Band
1
0
1
0
1
20(decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
* It depends on model, and can adjust when sound
mode is EQ adjustable value.
19.Energy Saving (Command: j q)
►► To reduce the power consumption of the TV. You
can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Data
00 : Off
01 : Minimum
02 : Medium
03 : Maximum
04 : Auto (For LCD TV / LED TV) /
Intelligent sensor (For PDP TV)
05 : Screen off
* (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
20.Tune Command (Command: m a)
* This command may work differently depending on
model and signal.
• For Europe, Mid-East, Colombia, Asia except
South Korea and Japan Model
►► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
* Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data
Data00 : High Channel data
Data01 : Low Channel data
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
Data02 : Input Source (Digital)
- 10 : Antenna TV (DTV)
- 20 : Antenna Radio (Radio)
- 40 : Satellite TV (SDTV)
- 50 : Satellite Radio (S-Radio)
- 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
* Tune Command Examples:
1.Tune to the Analog antenna (PAL) Channel 10.
Set ID = All = 00
Data 00 & 01 = Channel Data is 10 = 00 0a
Data 02 = Analog Antenna TV = 00
Result = ma 00 00 0a 00
2.Tune to the digital antenna (DVB-T) Channel 01.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1 = 00 01
Data 02 = Digital Antenna TV = 10
Result = ma 00 00 01 10
3.Tune to the satellite (DVB-S) Channel 1000.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1000 = 03 E8
Data 02 = Digital Satellite TV = 40
Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
• For South Korea, North/Latin America except
Colombia Model
►► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
the Physical number is not required when sending a
command in Digital.
ENGLISH
ENG
18.Equalizer (Command : j v)
9
10 EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
* Analog Antenna/Cable
Data00 : Physical Channel Number
- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number
Data01 & 02: xx (Don't care)
Data03 & 04: xx (Don't care)
Data05: Input Source (Analog)
- 00 : Antenna TV (ATV)
- 01 : Cable TV (CATV)
2.Tune to the digital antenna (ATSC) channel 30-3.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = Digital Antenna TV = 22
Total = ma 00 00 00 1E 00 03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
• For Japan Model
* Digital Antenna/Cable
►► To tune channel to following physical/major/minor
number.
Data00 : xx (Don't care)
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[Data 01][Data 02]: Major Channel Number
Data01 : High byte Channel Data
Data02 : Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number
Data03 : High byte Channel Data
Data04 : Low byte Channel Data
Data05 : Input Source (Digital)
- 02 : Antenna TV (DTV) – Use Physical Channel
Number
- 06 : Cable TV (CADTV) – Use Physical Channel
Number
- 22 : Antenna TV (DTV) – Don’t Use Physical
Channel Number
- 26 : Cable TV (CADTV) - Don’t Use Physical
Channel Number
- 46 : Cable TV (CADTV) – Use Physical/Major
Channel Number Only (One Part Channel)
- 66 : Cable TV (CADTV) – Use Major Channel
Number Only (One Part Channel)
- 0b : Cable DTV Plus – Use Physical Channel
Number
- 2b : Cable DTV Plus – Don’t Use Physical
Channel Number
- 4b : Cable DTV Plus – Use Physical/Major
Channel Number Only (One Part Channel)
- 6b : Cable DTV Plus – Use Major Channel
Number Only (One Part Channel)
Two bytes are available for each major and minor
channel data, but usually the low byte is used alone
(high byte is 0).
* Tune Command Examples:
1.Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analog Cable TV = 01
Total = ma 00 23 00 00 00 00 01
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
* Digital Antenna/Satellite
Data 00: xx (Don't care)
[Data 01][Data 02]: Major Channel Number
Data 01: High byte Channel Data
Data 02: Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number
(Don’t care in Satellite)
Data 03: High byte Channel Data
Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan)
- 02 : Antenna TV (DTV)
- 42 : Antenna TV (DTV) – Use Physical/Major
Channel Number Only (One Part Channel)
- 62 : Antenna TV (DTV) – Use Major Channel
Number Only (One Part Channel)
- 07 : BS (Broadcasting Satellite)
- 08 : CS1 (Communication Satellite 1)
- 09 : CS2 (Communication Satellite 2)
* Tune Command Examples:
1 Tune to the digital antenna (ISDB-T) channel 17-1.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 17 = 00 11
Data 03 & 04 = Minor/Branch is 1 = 00 01
Data 05 = Digital Antenna TV = 02
Total = ma 00 00 00 11 00 01 02
EXTERNAL CONTROL DEVICE SETUP
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
* This feature is varied based on the model.
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
21.Channel(Programme) Add/Del(Skip)
(Command: m b)
►► To skip current channel(programme) for next time.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Set the saved channel status to del(ATSC, ISDB)/
skip(DVB) or add.
22.Key (Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
DataKey code - p.2.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
23.Control Backlight (Command: m g)
• For LCD TV / LED TV
►► To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Control Panel Light (Command: m g)
• For Plasma TV
►► To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Data
00 : DTV
01 : CADTV
02 : Satellite DTV
10 : ATV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
20 : AV or AV1
21 : AV2
40 : Component1
60 : RGB
41 : Component2
90 : HDMI1
92 : HDMI3
91 : HDMI2
93 : HDMI4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
25.3D(Command: x t) (only 3D models)
(Depending on model)
►► To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][ ][Data 03][Cr]
* (Depending on model)
DataStructure
[Data 00]00 : 3D On
01 : 3D Off
02 : 3D to 2D
03 : 2D to 3D
[Data 01]00 : Top and Bottom
01 : Side by Side
02 : Check Board
03 : Frame Sequential
04 : Column interleaving
05 : Row interleaving
[Data 02]00 : Right to Left
01 : Left to Right
[Data 03]3D Effect(3D Depth): Min : 00 - Max : 14
(*transmit by Hexadecimal code)
ENGLISH
ENG
24.Input select (Command: x b)
(Main Picture Input)
2.Tune to the BS (ISDB-BS) channel 30.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Don’t Care = 00 00
Data 05 = Digital BS TV = 07
Total = ma 00 00 00 1E 00 00 07
Data 00 : Del(ATSC,ISDB)/Skip(DVB)
11
12 EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
* [Data 02], [Data 03] functions depend on model
and signal.
* If [Data 00] is 00 (3D On), [Data 03] has no
meaning.
3) When[Data 00] is 06, 07
00 : Off
01 : On
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data
03] works when 3D Mode (Genre) is manual only.
4) When[Data 00] is 08
00 : Revert to 3D video from 3D-to-2D
converted 2D video
01 : Change 3D video to 2D video, except
2D-to-3D video
* If conversion condition doesn’t meet, command is
treated as NG.
* All 3D pattern options ([Data 01]) may not be
available according to broadcasting/video signal.
5) When [Data 00] is 09
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data
01], [Data 02] and [Data 03] have no meaning.
* If [Data 00] is 03 (2D to 3D), [Data 01] and
[Data 02] have no meaning.
00 : Standard
02 : Cinema
04 : Manual
01 : Sport
03 : Extreme
05 : Auto
[Data 00]
[Data 01]
[Data 02]
[Data 03]
00
O
O
O
01
X
X
X
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]
02
X
X
X
[v][ ][Set ID][ ][NG][Data00][x]
03
X
O
O
X : don’t care
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
[Data03][x]
[t][ ][Set ID][ ][NG][Data00][x]
26.Extended 3D(Command: x v) (only 3D models)
(Depending on model)
►► To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
[Data 01][Cr]
[Data 00]3D option
00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
06 : 3D Color Correction
07 : 3D Sound Zooming
08 : Normal Image View
09 : 3D Mode (Genre)
[Data 01]It has own range for each 3D option
determined by [Data 00].
1) When[Data 00] is 00
00 : Right to Left
01 : Left to Right
2) When[Data 00] is 01, 02
DataMin: 0 - Max: 14 (*transmit by Hexadecimal
code)
Data value range(0 - 20) converts Viewpoint range
(-10 - +10) automatically (Depending on model)
* This option works when 3D Mode (Genre) is manual
only.
27.Auto Configure (Command: j u)
(Depending on model)
►► To adjust picture position and minimize image
shaking automatically. It works only in RGB (PC)
mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Download PDF

advertising