LG | 55LA9600 | LG 55LA9600 Owner's manual

OWNER’S MANUAL
LED TV
* LG LED TV refers to an LCD screen with LED backlights.
Please read this manual carefully before operating
your set and retain it for future reference.
55LA7900
47LA8600
55LA8600
60LA8600
55LA9600
www.lg.com
2
SAFETY INSTRUCTIONS
Safety Instructions
Please read these safety precautions carefully before using the product.
yyDo not plug too many electrical
devices into a single multiple electrical
outlet. Otherwise, this may result in
fire due to over-heating.
WARNING
yyDo not place the TV and/or remote
control in the following environments:
- A location exposed to direct sunlight
- An area with high humidity such as a
bathroom
- Near any heat source such as stoves
and other devices that produce heat
- Near kitchen counters or humidifiers
where they can easily be exposed
to steam or oil
- An area exposed to rain or wind
- Near containers of water such as
vases
Otherwise, this may result in fire,
electric shock, malfunction or
product deformation.
yyDo not place the product where it
might be exposed to dust. This may
cause a fire hazard.
yyMains Plug is the TV connecting/
disconnecting device to AC mains
electric supply. This plug must remain
readily attached and operable when TV
is in use.
ENGLISH
yyDo not touch the power plug with wet
hands. Additionally, if the cord pin
is wet or covered with dust, dry the
power plug completely or wipe dust
off. You may be electrocuted due to
excess moisture.
yyMake sure to connect Mains cable
to compliant AC mains socket with
Grounded earth pin. (Except for
devices which are not grounded on
earth.) Otherwise possibility you may
be electrocuted or injured.
yyInsert power cable plug completely
into wall socket otherwise if not
secured completely into socket, fire
ignition may break out.
yyEnsure the power cord does not come
into contact with hot objects such as
a heater. This may cause a fire or an
electric shock hazard.
yyDo not place a heavy object, or the
product itself, on power cables.
Otherwise, this may result in fire or
electric shock.
yyBend antenna cable between inside
and outside building to prevent rain
from flowing in. This may cause water
damaged inside the Product and could
give an electric shock.
yyWhen mounting TV onto wall make
sure to neatly install and isolate
cabling from rear of TV as to not
create possibility of electric shock / fire
hazard.
yyDo not drop the product or let it
fall over when connecting external
devices. Otherwise, this may result in
injury or damage to the product.
Des
icca
nt
yyKeep the anti-moisture packing
material or vinyl packing out of the
reach of children. Anti-moisture
material is harmful if swallowed. If
swallowed by mistake, force the
patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the
reach of children.
yyDo not let your children climb or cling
onto the TV. Otherwise, the TV may
fall over, which may cause serious
injury.
yyDispose of used batteries carefully
to ensure that a small child does not
consume them. Please seek DoctorMedical Attention immediately if child
consumes batteries.
yyDo not insert any metal objects/
conductors (like a metal chopstick/
cutlery/ screwdriver) between power
cable plug and input Wall Socket while
it is connected to the input terminal on
the wall. Additionally, do not touch the
power cable right after plugging into
the wall input terminal. You may be
electrocuted. (Depending on model)
yyDo not put or store inflammable
substances near the product. There
is a danger of combustion/explosion
or fire due to careless handling of the
inflammable substances.
yyDo not drop metallic objects such as
coins, hair pins, chopsticks or wire into
the product, or inflammable objects
such as paper and matches. Children
must pay particular attention. Electrical
shock, fire or injury can occur. If a
foreign object is dropped into the
product, unplug the power cord and
contact the service centre.
yyDo not spray water on the product or
scrub with an inflammable substance
(thinner or benzene). Fire or electric
shock accident can occur.
yyDo not allow any impact, shock or any
objects to fall into the unit, and do not
drop anything onto the screen. You
may be injured or the product can be
damaged.
SAFETY INSTRUCTIONS
yyNever touch this product or antenna
during a thunder or lighting storm. You
may be electrocuted.
yyNever touch the wall outlet when
there is leakage of gas, open the
windows and ventilate. It may cause a
fire or a burn by a spark.
yyDo not disassemble, repair or modify
the product at your own discretion.
Fire or electric shock accident can
occur. Contact the service centre for
check, calibration or repair.
yyIf any of the following occur, unplug
the product immediately and contact
your local service centre.
- The product has been impacted by
shock
- The product has been damaged
- Foreign objects have entered the
product
- The product produced smoke or a
strange smell
This may result in fire or electric
shock.
yyUnplug the TV from AC mains wall
socket if you do not intend to use
the TV for a long period of time.
Accumulated dust can cause fire
hazard and insulation deterioration can
cause electric leakage/shock/fire.
yyApparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases, shall
be placed on the apparatus.
yyInstall the product where no radio wave
occurs.
yyThere should be enough distance
between an outside antenna and power
lines to keep the former from touching
the latter even when the antenna falls.
This may cause an electric shock.
yyDo not install the product on places
such as unstable shelves or inclined
surfaces. Also avoid places where there
is vibration or where the product cannot
be fully supported. Otherwise, the
product may fall or flip over, which may
cause injury or damage to the product.
yyIf you install the TV on a stand, you need
to take actions to prevent the product
from overturning. Otherwise, the
product may fall over, which may cause
injury.
yyIf you intend to mount the product to a wall, attach VESA
standard mounting interface (optional parts) to the back of the
product. When you install the set to use the wall mounting
bracket (optional parts), fix it carefully so as not to drop.
yyOnly use the attachments / accessories specified by the
manufacturer.
yyWhen installing the antenna, consult a
qualified service man. This may create a
fire hazard or an electric shock hazard.
yyWe recommend that you maintain a
distance of at least 2 to 7 times the
diagonal screen size when watching
TV. If you watch TV for a long period of
time, this may cause blurred vision.
yyOnly use the specified type of battery.
This could cause damage to the remote
control.
yyDo not mix new batteries with old
batteries. This may cause the batteries
to overheat and leak.
yyUsed batteries including rechargeable
battery must be collected separately and
recycled.
yyMake sure there are no objects between
the remote control and its sensor.
yySignal from Remote Control can be
interrupted due to external/internal
lighting eg Sunlight, fluorescent lighting.
If this occurs turn off lighting or darken
viewing area.
yyWhen connecting external devices such
as video game consoles, make sure
the connecting cables are long enough.
Otherwise, the product may fall over,
which may cause injury or damage the
product.
yyDo not turn the product On/Off by
plugging-in or unplugging the power
plug to the wall outlet. (Do not use the
power plug for switch.) It may cause
mechanical failure or could give an
electric shock.
yyPlease follow the installation instructions
below to prevent the product from
overheating.
- The distance between the product and
the wall should be more than 10 cm.
- Do not install the product in a place
with no ventilation (e.g., on a
bookshelf or in a cupboard).
- Do not install the product on a carpet
or cushion.
- Make sure the air vent is not blocked
by a tablecloth or curtain.
Otherwise, this may result in fire.
yyTake care not to touch the ventilation
openings when watching the TV for long
periods as the ventilation openings may
become hot. This does not affect the
operation or performance of the product.
yyPeriodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
yyPrevent dust collecting on the power
plug pins or outlet. This may cause a fire
hazard.
yyProtect the power cord from physical
or mechanical abuse, such as being
twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular
attention to plugs, wall outlets, and the
point where the cord exits the appliance.
ENGLISH
CAUTION
3
4
SAFETY INSTRUCTIONS
yyDo not press strongly upon the panel
with a hand or sharp object such as nail,
pencil or pen, or make a scratch on it, as
it may cause damage to screen.
yyYou may find different brightness and
colour of the panel depending on your
viewing position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not
related with the product performance,
and it is not malfunction.
yyAvoid touching the screen or holding
your finger(s) against it for long periods
of time. Doing so may produce some
temporary or permanent distortion/
damage to screen.
yyWhen cleaning the product and its
components, unplug the power first
and wipe it with a soft cloth. Applying
excessive force may cause scratches or
discolouration. Do not spray with water
or wipe with a wet cloth. Never use
glass cleaner, car or industrial shiner,
abrasives or wax, benzene, alcohol etc.,
which can damage the product and its
panel. Otherwise, this may result in
fire, electric shock or product damage
(deformation, corrosion or breakage).
yyAs long as this unit is connected to the AC wall outlet, it is
not disconnected from the AC power source even if you turn
off this unit by SWITCH.
yyWhen unplugging the cable, grab the
plug and unplug it, by pulling at the
plug. Don’t pull at the cord to unplug the
power cord from the power board, as
this could be hazardous.
yyWhen moving the product, make sure
you turn the power off first. Then,
unplug the power cables, antenna
cables and all connecting cables. The
TV set or power cord may be damaged,
which may create a fire hazard or cause
electric shock.
yyDisplaying a still image (e.g., broadcasting channel logo, onscreen menu, scene from a video game) for a prolonged time
may cause damage to the screen, resulting in retention of the
image, which is known as image sticking. The warranty does
not cover the product for image sticking.
Avoid displaying a fixed image on your television’s screen for
a prolonged period (2 or more hours for LCD, 1 or more hours
for Plasma). Also, if you watch the TV at a ratio of 4:3 for a
long time, image sticking may occur on the borders of the
panel. This phenomenon also occurs in third-party products
and is not subject to exchange or refund.
yyGenerated Sound
“Cracking” noise: A cracking noise that occurs when
watching or turning off the TV is generated by plastic thermal
contraction due to tempera-ture and humidity. This noise is
common for products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level noise
is generated from a high-speed switching circuit, which
supplies a large amount of current to operate a product. It
varies depending on the product. This generated sound does
not affect the performance and reliability of the product.
ENGLISH
yyWhen moving or unpacking the product,
work in pairs because the product is
heavy. Otherwise, this may result in
injury.
yyContact the service centre once a year
to clean the internal parts of the product.
Accumulated dust can cause mechanical
failure.
yyRefer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
yyIf the product feels cold to the touch,
there may be a small “flicker” when
it is turned on. This is normal, there is
nothing wrong with product.
yyThe panel is a high technology display
product with resolution of two million
to six million pixels. You may see tiny
black dots and/or brightly coloured dots
(red, blue or green) at a size of 1 ppm
on the panel. This does not indicate
a malfunction and does not affect
the performance and reliability of the
product. This phenomenon also occurs
in third-party products and is not subject
to exchange or refund.
WARNING
If you ignore the warning message, you may be
seriously injured or there is a possibility of accident
or death.
CAUTION
If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
The note helps you understand and use the product
safely. Please read the note carefully before using
the product.
SAFETY INSTRUCTIONS
Viewing 3D Imaging
5
CAUTION
Viewing Environment
WARNING
Viewing Environment
yyViewing Time
- When watching 3D content, take 5 - 15 minute
breaks every hour. Viewing 3D content for a long
period of time may cause headache, dizziness,
fatigue or eye strain.
Those that have a photosensitive seizure or
chronic illness
Symptoms which require discontinuation or
refraining from watching 3D content
yyDo not watch 3D content when you feel fatigue
from lack of sleep, overwork or intoxication .
yyWhen these symptoms are experienced, stop using/
watching 3D content and get enough rest until the
symptom subsides.
- Consult your doctor when the symptoms persist.
Symptoms may include headache, eyeball
pain, dizziness, nausea, palpitation, blurriness,
discomfort, double image, visual inconvenience or
fatigue.
Viewing Age
yyInfants / Children
- Usage/ Viewing 3D content for children under the
age of 5 is prohibited.
- Children under the age of 10 may overreact and
become overly excited because their vision is in
development. For example: trying to touch the
screen or trying to jump into it. Special monitoring
and extra attention is required for children watching
3D content.
- Children have greater binocular disparity of 3D
presentations than adults because the distance
between the eyes is shorter than one of adults.
Therefore they will perceive more stereoscopic
depth compared to adults for the same 3D image.
yyTeenagers
- Advise teenagers under the age of 19 not to watch
3D videos for a long time when they are tired.
yyElderly
- The elderly may perceive less of a 3D effect than
the youth. Do not sit closer to the TV than the
recommended distance.
Cautions when using the 3D glasses
yyMake sure to use LG 3D glasses. Otherwise, you
may not be able to view 3D videos properly.
yyDo not use 3D glasses instead of your normal
glasses, sunglasses or protective goggles.
yyUsing modified 3D glasses may cause eye strain or
image distortion.
yyDo not keep your 3D glasses in extremely high or
low temperatures. It will cause deformation.
yyThe 3D glasses are fragile and are easy to
scratched. Use a soft, clean piece of cloth when
wiping the lenses. Do not scratch the lenses of the
3D glasses with sharp objects or clean/wipe them
with chemicals.
ENGLISH
yySome users may experience a seizure or other
abnormal symptoms when they are exposed to a
flashing light or particular pattern from 3D content.
yyDo not watch 3D videos if you feel nauseous,
are pregnant and/ or have a chronic illness such
as epilepsy, cardiac disorder, or blood pressure
disease, etc.
yy3D Content are not recommended for those who
suffer from stereo blindness or stereo anomaly.
Double images or discomfort in viewing may be
experienced.
yyIf you have strabismus (cross-eyed), amblyopia
(weak eyesight) or astigmatism, you may have
trouble sensing depth and easily feel fatigue due to
double images. It is advised to take frequent breaks
than the average adult.
yyIf your eyesight varies between your right and left
eye, revise your eyesight prior to watching 3D
content.
yyViewing Distance
- Maintain a distance of at least twice the screen
diagonal length when watching 3D content.
If you feel discomfort in viewing 3D content,
move further away from the TV.
6
LICENSES / OPEN SOURCE SOFTWARE NOTICE
LICENSES
Supported licenses may differ by model. For more information about licenses, visit ‘www.lg.com’.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for
more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to
play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate
the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on
how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274”
ENGLISH
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other
U.S. and worldwide patents issued & pending. DTS, the Symbol & DTS and the Symbol
together are registered trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product
includes software. © DTS, Inc. All Rights Reserved.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product,
please visit ‘http://opensource.lge.com’.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for
download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping and handling) upon email request to ‘opensource@lge.com’. This offer
is valid for three (3) years from the date on which you purchased the product.
TABLE OF CONTENTS
7
TABLE OF CONTENTS
2
Safety Instructions
5
Viewing 3D Imaging
6
LICENSES
32
Magic Remote Control
Functions
33
33
33
Registering Magic Remote Control
How to use Magic Remote Control
Precautions to Take when Using the Magic
Remote Control
6OPEN SOURCE SOFTWARE NOTICE
34REMOTE CONTROL
7TABLE OF CONTENTS
36Using the user guide
8
Installation Procedure
37
SPECIFICATIONS
8ASSEMBLING AND PREPARING
Unpacking
Optional Extras
Parts and Buttons
Lifting and moving the TV
Setting up the TV
-Attaching the stand
-Mounting on a table
-Tidying cables
-Mounting on a wall
Using Built-in Camera
-Preparing Built-in Camera
-Name of Parts for the Built-In Camera
-Checking the Camera’s Shooting Range
22
MAKING CONNECTIONS
22
23
Connecting to an antenna or cable
Connecting to a HD receiver, DVD Player, or
VCR
-HDMI Connection
-DVI to HDMI Connection
-Connecting to a mobile phone
-Component Connection
-Composite Connection
Connecting to a PC
-HDMI Connection or DVI to HDMI
Connection
Connecting to an Audio System
-Digital Optical Audio Connection
Connecting Headphones
Connecting a USB Drive
23
24
25
26
27
28
28
30
30
31
31
41external control device setup
42 MAINTENANCE
42
42
42
Cleaning Your TV
-Screen, frame, cabinet and stand
-Power cord
42TROUBLESHOOTING
ENGLISH
8
11
12
14
15
15
17
18
19
20
20
20
21
NOTE
yyImage shown may differ from your TV.
yyYour TV’s OSD (On Screen Display) may differ
slightly from that shown in this manual.
yyThe available menus and options may differ from
the input source or product model that you are
using.
yyNew features may be added to this TV in the
future.
8
Instalation Procedure / ASSEMBLING AND PREPARING
Installation Procedure
1
Open the package and make sure all the accessories are included.
2
Attach the stand to the TV set.
3
Connect an external device to the TV set.
4
Make sure the network connection is available.
You can use the TV network functions only when the network connection is made.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
ENGLISH
CAUTION
yyDo not use any unapproved items to ensure the safety and product life span.
yyAny damages or injuries by using unapproved items are not covered by the warranty.
yyIn case of some model, the thin film on screen is a part of TV, So don’t take it off.
NOTE
yyThe items supplied with your product may vary depending on the model.
yyProduct specifications or contents of this manual may be changed without prior notice due to upgrade of product
functions.
yyFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm
width.
yyUse an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s
USB port.
B
A
B
A
*A ≤ 10 mm
*B ≤ 18 mm
ASSEMBLING AND PREPARING
9
For LA7900 series
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
LIST
8
9
0
FLASHBK
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Magic Remote Control,
Batteries (AA)
(See p. 32)
Remote control and Batteries
(AAA)
(See p. 34)
Owner’s Manual
Tag On
Stand Base, Stand Body
(See p. 15)
Tag On
Cinema 3D Glasses
The number of 3D glasses may
differ depending on the model
or country.
Component video cable
(See p. 26)
Composite video cable
(See p. 26, 27)
Cable Holder
(See p. 18)
Cable Management
2 EA
(See p. 18)
Power Cord
ENGLISH
Stand Screws
8 EA, M4 x 14
(See p. 15)
10
ASSEMBLING AND PREPARING
For LA8600, LA9600 series
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
LIST
8
9
0
FLASHBK
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
ENGLISH
Magic Remote Control,
Batteries (AA)
(See p. 32)
Remote control,
Batteries (AAA)
(See p. 34)
Owner’s Manual
Cable Holder
(See p. 18)
Stand Base
(See p. 16)
Power Cord
(For LA8600 series)
(For LA9600 series)
Tag On
(Depending on model)
Stand Screws
4 EA, M4 x 16
(See p. 16)
Stand Screws
4 EA, M4 x 20
(See p. 16)
Component video cable
(See p. 26)
Composite video cable
(See p. 26, 27)
Cinema 3D Glasses
The number of 3D glasses may
differ depending on the model
or country.
Tag On
ASSEMBLING AND PREPARING
11
Optional Extras
Optional extras can be changed or modified for quality improvement without any notification.
Contact your dealer for buying these items.
These devices only work with certain models.
The model name or design may be changed due to the manufacturer’s circumstances or policies.
AN-MR400
Magic Remote
AG-F***
Cinema 3D Glasses
AG-F***DP
Dual Play Glasses
Tag On
Tag On
Wall mount bracket
LSW430B
AN-BL***
Wireless IR Blaster
(Depending on model)
Compatibility
AN-VC5**
Video Call Camera
ENGLISH
LG Audio device
LA7900
LA8600
LA9600
AN-MR400 Magic remote
•
•
•
AG-F*** Cinema 3D glasses
•
•
•
AG-F***DP Dual Play Glasses
•
•
•
AN-VC5** Video Call Camera
•
(Built-in)
(Built-in)
Tag On
•
•
•
LG Audio device
•
•
•
12
ASSEMBLING AND PREPARING
Parts and Buttons
For LA7900 series
Screen
OK
SETTINGS
INPUT
Speakers
Buttons
ENGLISH
Remote control sensor
LG Logo light
Button
Description
/
(
/
)
Scrolls through the saved channels.
/
(
/
)
Adjusts the volume level.
(OK
Selects the highlighted menu option or confirms an input.
)
(SETTINGS)
(INPUT
(
)
)
Accesses the main menus, or saves your input and exits the menus.
Changes the input source.
Turns the power on or off.
ASSEMBLING AND PREPARING
13
For LA8600, LA9600 series
Video call camera
Screen
OK
SETTINGS
INPUT
Speakers
Buttons
LG Logo light
Button
Description
/
(
/
)
Scrolls through the saved channels.
/
(
/
)
Adjusts the volume level.
(OK
Selects the highlighted menu option or confirms an input.
)
(SETTINGS)
(INPUT
(
)
)
Accesses the main menus, or saves your input and exits the menus.
Changes the input source.
Turns the power on or off.
ENGLISH
Remote control senser
14
ASSEMBLING AND PREPARING
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged and for
safe transportation regardless of its type and size.
CAUTION
yyAvoid touching the screen at all times, as this may
result in damage to the screen.
yyIt is recommended to move the TV in the box or
packing material that the TV originally came in.
yyBefore moving or lifting the TV, disconnect the
power cord and all cables.
yyWhen holding the TV, the screen should face away
from you to avoid damage.
yyHold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part, speaker,
or speaker grill area.
ENGLISH
yyWhen transporting a large TV, there should be at
least 2 people.
yyWhen transporting the TV by hand, hold the TV as
shown in the following illustration.
yyWhen transporting the TV, do not expose the TV to
jolts or excessive vibration.
yyWhen transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the left
or right.
ASSEMBLING AND PREPARING
15
Setting up the TV
You can mount your TV to a wall or attach the stand if you wish to place the TV on an entertainment center or other
furniture.
Attaching the stand
If you are not mounting the TV to a wall, use the following instructions to attach the stand.
CAUTION
yyWhen attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to
protect the screen from scratches.
yyMake sure that the screws are fastened tightly. (If they are not fastened securely enough, the TV may tilt forward
after being installed.)
yyDo not tighten the screws with too much force; otherwise they may be damaged and come loose later.
NOTE
yyRemove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.
For LA7900 series
1
3
M4 x 14
4 EA
ENGLISH
Stand body
Front
Stand base
2
M4 x 14
4 EA
16
ASSEMBLING AND PREPARING
For LA8600, LA9600 series
1
4
Front
Stand Base
2
ENGLISH
3
Wrapping bag
(Depending on model)
(LA8600 series)
M4 x 16
2 EA
(LA8600 series)
M4 x 16
2 EA
(LA9600 series)
M4 x 20
2 EA
(LA9600 series)
M4 x 20
2 EA
17
ASSEMBLING AND PREPARING
Mounting on a table
1
Adjusting the angle of the TV to suit view
Lift and tilt the TV into its upright position on a table.
- Leave a 10 cm (minimum) space from the wall for
proper ventilation.
Swivel 15 degrees to the left or right and adjust the
angle of the TV to suit your view.
(For 55LA7900)

15˚
15˚
10 cm
10 cm
10 cm
10 cm
Swivel 10 degrees to the left or right and adjust the
angle of the TV to suit your view.
(For 47LA8600)
2
Connect the power cord to a wall outlet.
CAUTION
10˚
10˚
yyDo not place the TV near or on sources of heat, as
this may result in fire or other damage.
8˚
8˚
NOTE
yyWhen adjusting the angle of the TV, watch out for
your fingers.
»»Personal injury may occur if hands or fingers are
pinched. If the product is tilted too much, it may fall,
causing damage or injury.
Rear
Front
ENGLISH
Swivel 8 degrees to the left or right and adjust the angle
of the TV to suit your view.
(For 55LA8600, 60LA8600)
18
ASSEMBLING AND PREPARING
Securing the TV to a wall (optional)
(Depending on model)
Tidying cables
(For LA7900 Series)
1
Gather and bind the cables with the Cable Holder
and the Cable Management.
2
Fix the Cable Management firmly to the TV.
⨲㘶ᖂ2
㏪ⱞ⋾#Ɐᴏ
Cable Holder
ENGLISH
1
Insert and tighten the eye-bolts, or TV brackets and
bolts on the back of the TV.
- If there are bolts inserted at the eye-bolts position,
remove the bolts first.
2
Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eyebolts on the rear of the TV.
3
Connect the eye-bolts and wall brackets tightly with
a sturdy rope.
Make sure to keep the rope horizontal with the flat
surface.
Cable Management
(For LA8600, LA9600 Series)
1
Gather and bind the cables with the cable
management clip.
2
Gather and bind the cables with the cable holder on
the back of the TV.
CAUTION
yyMake sure that children do not climb on or hang on
the TV.
NOTE
yyUse a platform or cabinet that is strong and large
enough to support the TV securely.
yyBrackets, bolts and ropes are optional. You can
obtain additional accessories from your local dealer.
Cable Holder
CAUTION
yyDo not move the TV by holding the cable holder
and cable management, as the cable holders may
break, and injuries and damage to the TV may
occur.
ASSEMBLING AND PREPARING
Mounting on a wall
19
Wall mount bracket (optional)
An optional wall mount can be used with your LG
Television. Consult with your local dealer for a wall
mount that supports the VESA standard used by your
TV model. Carefully attach the wall mount bracket at the
rear of the TV. Install the wall mount bracket on a solid
wall perpendicular to the floor. If you are attaching the
TV to other building materials, please contact qualified
personnel to install the wall mount. Detailed instructions
will be included with the wall mount. We recommend
that you use an LG brand wall mount.
10 cm
10 cm
10 cm
10 cm
LSW430B
MSW240
CAUTION
yyDisconnect the power first, and then move or
install the TV. Otherwise electric shock may occur.
yyIf you install the TV on a ceiling or slanted wall, it
may fall and result in severe injury.
Use an authorized LG wall mount and contact the
local dealer or qualified personnel.
yyDo not over tighten the screws as this may cause
damage to the TV and void your warranty.
yyUse the screws and wall mounts that meet the
VESA standard. Any damages or injuries by misuse
or using an improper accessory are not covered by
the warranty.
NOTE
Make sure to use screws and wall mounts that meet the
VESA standard. Standard dimensions for the wall mount
kits are described in the following table.
55LA7900 47LA8600 55LA9600
55LA8600
VESA (A x B)
400 x 400
A
B
Standard screw
M6
Number of screws 4
Wall mount
bracket (optional)
MSW240
LSW430B
Model
60LA8600
VESA (A x B)
400 x 400
A
B
Standard screw
M6
Number of screws 4
Wall mount
bracket (optional)
LSW430B
ENGLISH
Model
yyUse the screws that are listed on the VESA
standard screw specifications.
yyThe wall mount kit includes an installation manual
and necessary parts.
yyThe wall mount bracket is optional. You can obtain
additional accessories from your local dealer.
yyThe length of screws may differ depending on the
wall mount. Make sure to use the proper length.
yyFor more information, refer to the manual supplied
with the wall mount.
20
ASSEMBLING AND PREPARING
Using Built-in Camera
2
For LA8600, LA9600 series
You can adjust the angle of the camera with the
angle adjustment lever on the back of the built-in
camera (within 5 degrees vertically).
This TV does not support the use of an external
camera.
Angle Adjustment
Lever
NOTE
yyBefore using the built-in camera, you must
recognize the fact that you are legally responsible
for the use or misuse of the camera by the relevant
national laws including the criminal law.
yyThe relevant laws include the Personal Information
Protection law which regulates the processing
and transferring of personal information and the
law which regulates the monitoring by camera in a
workplace and other places.
yyWhen using the built-in camera, the user must gain
consent from the persons being observed. Please
avoid using the camera in the following manner.
We suggest avoiding the following situations:
(1) Using the camera in areas where the use of
camera is generally prohibited such as restroom,
locker room, fitting room and security area.
(2) Using the camera while causing the
infringement of privacy.
(3) Using the camera while causing the violation of
the relevant regulations or laws.
3
Pull down the built-in camera when you are not using
it.
Preparing Built-in Camera
ENGLISH
1. Pull up the slide at the back of the TV.
Slide
Name of Parts for the Built-In Camera
Microphone
Indicator
Camera Lens
NOTE
yyRemove the protective film before using the builtin camera.
ASSEMBLING AND PREPARING
21
Checking the Camera’s Shooting Range
1
Press the SMART button on the remote control to
display the More menu.
2
Select Settings from the More menu and then press
the wheel (OK) button.
3
Go to OPTION
Camera Setting Help and press
the wheel (OK) button.
NOTE
yyThe optimal distance from the camera to use the
motion recognition function is between 1.5(5 ft)
and 4.5 m(15 ft).
ENGLISH
22
MAKING CONNECTIONS
MAKING CONNECTIONS
yyThis section uses illustrations of the LA8600 series.
You can connect various external devices to the TV. Supported external devices are: HD receivers, DVD players, VCRs,
audio systems, USB storage devices, PC, gaming devices, and other external devices. For more information on external
device’s connection, refer to the manual provided with each device.
NOTE
yyIf you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the
TV through a DVD recorder or VCR. For more information of recording, refer to the manual provided with the
connected device.
yyThe external device connections shown may differ slightly from illustrations in this manual.
yyConnect external devices to the TV regardless of the order of the TV port.
yyIf you connect a gaming device to the TV, use the cable supplied with the gaming device.
yyRefer to the external equipment’s manual for operating instructions.
Connecting to an antenna or cable
Connect an antenna, cable, or cable box to watch TV while referring to the following. The illustrations may differ from
the actual items and a RF cable is optional.
VHF Antenna
UHF Antenna
Antenna
ENGLISH
or
Wall Jack
(*Not Provided)
(*Not Provided)
NOTE
yyTo improve the picture quality in a poor signal area,
please purchase a signal amplifier and install it
properly.
yyUse a signal splitter to use more than 2 TVs.
yyIf the antenna is not installed properly, contact your
dealer for assistance.
yyDTV Audio Supported Codec: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC.
MAKING CONNECTIONS
23
Connecting to a HD receiver, DVD Player, or VCR
Connect a HD receiver, DVD Player, or VCR to the TV and select an appropriate input mode.
HDMI Connection
HDMI is the best way to connect a device.
Transmits the digital video and audio signals from an external device to the TV. Connect the external device and the TV
with the HDMI cable as shown in the following illustration.
NOTE
yyUse the latest High Speed HDMI™ Cable with CEC (Customer Electronics Control) function.
yyHigh Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher.
yySupported HDMI Audio format : Dolby Digital, PCM (Up to 192 kHz, 32 kHz / 44.1 kHz / 48 kHz / 88 kHz /
96 kHz / 176 kHz / 192 kHz), DTS.
Choose any HDMI input port to connect.
It does not matter which port you use.
HDMI
(*Not Provided)
ARC (Audio Return Channel)
yyWhen connected with a high-speed HDMI cable,
digital audio can be sent to a compactible device
without an additional optical audio cable.
yyARC is only supported on the HDMI input 1 (ARC)
port. An external audio device that supports ARC
should be connected to HDMI 1 if you wish to use
ARC
ENGLISH
DVD / Blu-Ray / HD Cable Box / HD STB
24
MAKING CONNECTIONS
DVI to HDMI Connection
Transmits the digital video signal from an external device to the TV. Connect the external device and the TV with the
DVI-HDMI cable as shown in the following illustration. To transmit an audio signal, connect an audio cable.
NOTE
yyWhen using the HDMI/DVI cable, Single link is only supported.
Choose any HDMI input port to connect.
It does not matter which port you use.
(*Not Provided)
ENGLISH
YELLOW
DVI OUT
(*Not Provided)
AUDIO OUT
DVD / Blu-Ray / HD Cable Box
MAKING CONNECTIONS
25
Connecting to a mobile phone
Mobile High-definition Link (MHL) is an interface for transmitting digital audiovisual signals from mobile phones to
television sets.
NOTE
4 (MHL)
yyConnect the mobile phone to the HDMI IN 4 (MHL) port to view the phone screen on the TV.
yyThis only works for the MHL-enabled phone.
yyWith some MHL supporting mobile phones, you can use the TV remote to control the phone.
yyAn MHL passive cable is needed to connect the TV and a mobile phone.
yyRemove the MHL cable from the TV when:
- the MHL function is disabled.
- your mobile device is fully charged in standby mode.
MHL Cable
(*Not Provided)
Mobile phone
ENGLISH
26
MAKING CONNECTIONS
Component Connection
Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with
a component cable as shown in the following illustration.
NOTE
yyIf cables are installed incorrectly, it could cause the image to display in black and white or with distorted color.
yyCheck to ensure the cables are matched with the corresponding color connection.
AV
VIDEO AUDIO
IN
COMPONENT
PR PB
ENGLISH
GREEN
YELLOW
(Use the composite video cable provided.)
(Use the component video cable provided.)
GREEN
BLUE
GREEN
RED
GREEN
BLUE
RED
BLUE
RED
RED
WHITE
RED
WHITE
RED
WHITE
YELLOW
L
Y
R
AUDIO
VIDEO
DVD / Blu-Ray / HD Cable Box
MAKING CONNECTIONS
27
Composite Connection
Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with
the composite cable as shown in the following illustration.
NOTE
yyCheck to ensure the cables are matched with the corresponding color connection.
IN
AV
COMPONENT
VIDEO AUDIO
PR PB
Y
ENGLISH
YELLOW
(Use the composite video cable provided.)
RED
WHITE
RED
WHITE
RED
YELLOW
WHITE
YELLOW YELLOW
VIDEO
L (MONO) AUDIO R
VCR / DVD / Blu-Ray / HD Cable Box
28
MAKING CONNECTIONS
Connecting to a PC
NOTE
yyIt is recommended to use an HDMI connection for the best image quality.
yyDepending on the graphics card, DOS mode video may not work if a HDMI to DVI Cable is in use.
yyIn PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise
is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE menu until the picture is clear.
yyThe synchronization input form for Horizontal and Vertical frequencies is separate.
yyDepending on the graphics card, some resolution settings may not allow the image to be positioned on the screen
properly.
yyIf you are using DVI out from a PC, you have to connect analog audio separately. Refer to the instructions on the
next page.
yyWhen using the HDMI/DVI cable, Single link is only supported.
HDMI Connection or DVI to HDMI Connection
Choose method A or B to make connection.
Method A: HDMI Connection
Choose any HDMI input port to connect.
It does not matter which port you use.
ENGLISH
HDMI
(*Not Provided)
PC
MAKING CONNECTIONS
29
Method B: DVI to HDMI Connection
Choose any HDMI input port to connect.
It does not matter which port you use.
(*Not Provided)
YELLOW
AUDIO OUT
DVI OUT
PC
ENGLISH
(*Not Provided)
30
MAKING CONNECTIONS
Connecting to an Audio System
You can use an optional external audio system instead of the built-in speaker.
Digital Optical Audio Connection
Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV with the
optical audio cable as shown in the following illustration.
NOTE
yyDo not look into the optical output port. Looking at the laser beam may damage your vision.
yyAudio with ACP (Audio Copy Protection) function may block digital audio output.
ENGLISH
(*Not Provided)
OPTICAL AUDIO IN
Digital Audio System
MAKING CONNECTIONS
31
Connecting Headphones
You listen to the sound using headphones.
NOTE
yyAUDIO menu options are disabled when headphones are connected.
yyWhen changing AV MODE with headphones connected, the change is applied to video but not to audio.
yyOptical Digital Audio Out is not available when headphones are connected.
yyHeadphone impedance: 16 Ω
yyMax audio output: 0.624mW to 1.04mW
yyHeadphone jack size: 0.35 cm
Headphone
(*Not Provided)
Connecting a USB Drive
Connect a USB storage device such as a USB flash thumbdrive, external hard drive, or a USB memory card reader to the
TV and access the Smart Share menu to use various multimedia files.
NOTE
Choose any USB input port to connect.
It does not matter which port you use.
3(1A)
(*Not Provided)
USB
(*Not Provided)
HDD
ENGLISH
yySome USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect it to the
USB port on the TV directly.
32
MAGIC REMOTE CONTROL FUNCTIONS
Magic Remote Control Functions
When the message “Magic remote control battery is low. Change the battery.” is displayed, replace
the battery. To install batteries, open the battery cover, replace batteries (1.5 V AA) matching
and
ends to the label inside the compartment, and close the battery cover. Be sure to point
the remote control at the remote control sensor on the TV. To remove the batteries, perform the
installation actions in reverse.
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
yyIn Analogue TV and some countries, some remote control buttons may not work.
This remote uses infrared light. When in use, it should be pointed in the direction of the TV’s remote sensor.
(POWER)
Pointer (RF transmitter)
Turns the TV on or off.
BACK
Returns to the previous level.
SMART
Accesses the Smart Home.
LIGHTING ON/OFF
Turns the light on and off.
If you set it to ON, the light
automatically turns off in 5 seconds
Voice recognition
ENGLISH
-This is a beta version and only
available in selected functions for
supported models.
-Network connection is required to
use the voice recognition function.
1. Press the Voice recognition button.
2. Speak slowly and precisely.
When a voice is recognized, the
processing message appears on the
screen.
• Use the magic remote control no
further than 10 cm from your face.
Adjusts the volume level.
Used for viewing 3D video.
Wheel (OK)
P
Selects menus or options and confirms
your input.
Scrolls through the saved programmes.
If you press the navigation button while
moving the pointer on the screen,
the pointer disappears, and the Magic
Remote Control works as a regular
remote control.
To display the pointer again, shake the
Magic Remote Control from side to
side.
Navigation buttons
(up/down/left/right)
Scrolls through menus or options.
P
Scrolls through the saved programmes
or channels.
MUTE
Mutes all sounds.
/Q.MENU
Accesses the quick menus.
Accesses the Universal Control.
(Depending on country)
MAGIC REMOTE CONTROL FUNCTIONS
33
Registering Magic Remote Control
The Magic Remote Control operates by pairing with your
TV.
How to register the Magic Remote Control
(Wheel)
To register automatically, turn the TV on and
press the
Wheel (OK). When registration is
completed, the completion message appears
on the screen.
If registration fails, turn the TV off and back
on, then press the
Wheel (OK) to complete
registration.
How to Re-register the Magic Remote Control
BACK
SMART
1 Press and hold the
BACK and
buttons together for 5 seconds
SMART
to reset, then register it by following “How
to register the Magic remote control”
above.
2 To re-register the Magic remote control,
press and hold the
BACK button for 5
seconds toward the TV.
How to use Magic Remote Control
2
You can select More Menu.
Precautions to Take when Using
the Magic Remote Control
yyUse the Magic remote control within the maximum
communication distance (10 m, 32.8ft). Using the remote
control beyond this distance, or with an object obstructing it,
may cause a communication failure.
yyA communication failure may occur due to nearby devices.
Electrical devices such as a microwave oven or wireless
LAN product may cause interference, as these use the same
bandwidth (2.4 GHz) as the Magic remote control.
yyThe Magic remote control may be damaged or may
malfunction if it is dropped or receives a heavy impact.
yyTake care not to bump into nearby furniture or other people
when using the Magic remote control.
yyManufacturer and installer cannot provide service related to
human safety as the applicable wireless device has possibility
of electric wave interference.
yyIt is recommended that an Access Point (AP) be located more
than 1 m (3.28 ft) away from the TV. If the AP is installed
closer than 1 m (3.28 ft), the Magic remote control may not
perform as expected due to frequency interference.
ENGLISH
1 You can move the pointer by moving the
remote up and down or left and right.
»»If the pointer does not work properly,
wait 10 seconds and then try again.
2 If the pointer disappears, move the remote
control slightly to left or right. It will then
automatically appear on the screen.
»»If the pointer has not been used for a
certain period of time, it will disappear.
1
If you press Wheel(OK) on the Magic Remote Control, the
following screen appears.
Shows information about the current programme and
screen.
34
REMOTE CONTROL
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control. Please read this
manual carefully and use the TV correctly. To install batteries, open the battery cover,
and
ends to the label inside the compartment,
replace batteries (1.5 V AAA) matching the
and close the battery cover. To remove the batteries, perform the installation actions in reverse.
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
yyIn Analogue TV and some countries, some remote control buttons may not work.
This remote uses infrared light. When in use, it should be pointed in the direction of the TV’s remote sensor.
(POWER)
Turns the TV on or off.
RATIO
(User Guide)
Sees user-guide.
INPUT
RATIO
Resizes an image.
TV/
RAD
ENGLISH
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
INPUT
Changes the input source.
TV/RAD
Selects Radio, TV and DTV programme.
Number button
Enters numbers.
LIST
Accesses the saved channel list.
FAV
P
P
A
G
E
Q.VIEW
Tunes to the last channel viewed.
MUTE
INFO
SMART MY APPS
Adjusts the volume level.
FAV
Accesses your favorite channel list.
OK
Used for viewing 3D video.
BACK
GUIDE
EXIT
SUBTITLE
TEXT
T.OPT
Q.MENU
LIVE TV
REC
SETTINGS AV MODE
MUTE
Mutes all sounds.
P
Scrolls through the saved channels.
PAGE
Moves to the previous or next screen.
REMOTE CONTROL
35
INFO
Views the information of the current program and screen.
RATIO
INPUT
SMART
Accesses the Smart Home menu.
TV/
RAD
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
MY APPS
Shows the list of Apps.
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
OK ꔉ
Selects menus or options and confirms your input.
ꕣ BACK
Returns to the previous level.
GUIDE
Displays the program event according to time scheduler.
FAV
P
P
A
G
E
EXIT
Clears all on-screen displays and returns to TV viewing.
MUTE
INFO
SMART MY APPS
Color buttons
These access special functions in some menus.
: Red,
: Green,
: Yellow,
: Blue)
(
Q.MENU
Accesses the quick menu.
BACK
GUIDE
EXIT
SUBTITLE
TEXT
T.OPT
Q.MENU
LIVE TV
REC
SETTINGS AV MODE
SUBTITLE
Recalls your preferred subtitle in digital mode.
, )
Control buttons ( , , ,
Controls the Premium contents, Time Machine or
Smart Share menus or the SIMPLINK compatible
devices (USB or SIMPLINK or Time Machine).
LIVE TV
Returns to the LIVE TV.
REC
Start to record and display record menu.
SETTINGS
Accesses the main menu.
AV MODE
Selects an AV mode.
Accesses the AV devices connected with the HDMI
cable through HDMI-CEC.
Opens the SIMPLINK menu.
ENGLISH
TELETEXT BUTTONS ( TEXT, T.OPT)
These buttons are used for teletext.
OK
36
USING THE USER GUIDE
uSING tHE uSEr GuIdE
OPTION > To set language
SMART
User Guide allows you to more easily access the detailed
TV information.
1
2
Press SMART
menus.

1
User Guide
To use input device
To set time options
ENGLISH
PROGRAMME Setting
To set TV lock options
PICTURE, SOUND Setting
To set language
LG SMART Function
To set country
Advanced Function
To set subtitle
Information
To set Magic remote control
Index
2
Menu Language Selects a language for the display text.
[In Digital Mode Only]
Audio Language When watching a digital broadcast containing several
audio languages, you can select the language you want.
[In Digital Mode Only]
Use the Subtitle function when two or more subtitle
Subtitle
languages are broadcast.
Language
✎ If subtitle data in a selected language is not broadcast,
the default language subtitle will be displayed.
Voice
Select the language to make voice search.
Recognition
✎ Only the voice search adopted model can support this
setting.
Language
Wheel (OK)
User Guide
OPTION
eng
button to access the Smart Home
Select User Guide and press the
button.
3
4
Online User Guide
5
(Depending on country)
1
Shows the current watching programme or input
source screen.
2
Allows to select the category you want.
3
Allows to select the item you want.
You can use ꕌ/ꕍ to move between pages.
4
Allows to browse the description of the function
you want from the index.
5
Provides the detailed information on the functions
of LG Smart TV when the Internet is connected.
(It may not be available depending on the country/
language.)
➾ Settings ➙ OPTION ➙ Language
1
Selects Menu Language and Audio Language displayed on the screen.
GP4
2
Try Now
Close
1
Shows the description of the selected menu. You
can use
/
to move between pages.
2
Moves to the selected menu directly from the
User Guide.
SPECIFICATIONS
37
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
Hong-Kong
Digital TV
Analogue TV
Television System
DTMB
PAL D/K, PAL I, NTSC M
Program Coverage
DTMB : 21 to 69
PAL D/K : VHF/UHF 1 to 69, Cable 1 to 47
PAL I : VHF/UHF 1 to 69, Cable 1 to 47
NTSC M : VHF/UHF 2 to 78, Cable 1 to 71
External Antenna
Impedance
75 Ω
Operating Temperature 0 - 40 °C
Environment
condition
Operating Humidity
Less than 80 %
Storage Temperature
-20 - 60 °C
Storage Humidity
Less than 85 %
For the power supply and power consumption, refer to the label attached to the product.
MODELS
Dimensions (Width With stand
x Height x Depth)
Without stand
With stand
Weight
Without stand
Dimensions (Width With stand
x Height x Depth)
Without stand
With stand
Without stand
Power requirement
Dimensions (Width With stand
x Height x Depth)
Without stand
Power requirement
25.3 Kg
23 Kg
47LA8600
(47LA8600-CA)
1059 x 694 x 269 (mm)
1059 x 625 x 35.1 (mm)
19.3 Kg
17.2 Kg
AC 100-240 V~ 50 / 60 Hz
MODELS
Weight
1247 x 722 x 34.1 (mm)
AC 100-240 V~ 50 / 60 Hz
MODELS
Weight
1247 x 789 x 326 (mm)
With stand
Without stand
55LA8600
(55LA8600-CA)
1229 x 788 x 316 (mm)
1229 x 721 x 35.1 (mm)
26.2 Kg
23.4 Kg
AC 100-240 V~ 50 / 60 Hz
ENGLISH
Power requirement
55LA7900
(55LA7900-CA)
38
SPECIFICATIONS
MODELS
Dimensions (Width With stand
x Height x Depth)
Without stand
Weight
30.5 Kg
Without stand
27.7 Kg
AC 100-240 V~ 50 / 60 Hz
MODELS
Dimensions (Width With stand
x Height x Depth)
Without stand
Power requirement
1338 x 850 x 316 (mm)
1338 x 782 x 35.1 (mm)
With stand
Power requirement
Weight
60LA8600
(60LA8600-CA)
55LA9600
(55LA9600-CA)
1220 x 781 x 305 (mm)
1220 x 712 x 31.5 (mm)
With stand
21.0 Kg
Without stand
18.4 Kg
AC 100-240 V~ 50 / 60 Hz
ENGLISH
SPECIFICATIONS
HDMI (DTV) supported mode
Component port connecting information
Resolution
Horizontal Frequency
(kHz)
Vertical
Frequency (Hz)
640 x 480
31.469
31.5
59.94
60
720 x 480
31.469
31.5
59.94
60
720 x 576
31.25
50
1280 x 720
37.5
44.96
45
50
59.94
60
1920 x 1080
33.72
33.75
28.125
26.97
27
33.716
33.75
56.25
67.43
67.5
59.94
60
50
23.97
24
29.976
30.00
50
59.94
60
HDMI (PC) supported mode
Resolution
Horizontal
Frequency
(kHz)
39
Component ports on the
TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
Wireless LAN module (WN8122E1) specification
Vertical
Frequency (Hz)
31.468
70.09
720 x 400
31.469
70.08
640 x 480
31.469
59.94
800 x 600
37.879
60.31
1024 x 768
48.363
60.00
1152 x 864
54.348
60.053
1360 x 768
47.712
60.015
1280 x 1024
63.981
60.020
1920 x 1080
67.50
60.00
Frequency Range
Output Power (Max.)
IEEE802.11a/b/g/n
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz
802.11a: 16.5 dBm
802.11b: 16 dBm
802.11g: 15.5 dBm
802.11n - 2.4GHz: 15.5 dBm
802.11n - 5GHz: 16.5 dBm
Bluetooth module (BM-LDS401) specification
Standard
Frequency Range
Output Power (Max.)
Bluetooth Version 3.0
2400 ~ 2483.5 MHz
10 dBm or lower
ENGLISH
640 x 350
Standard
40
SPECIFICATIONS
3D supported mode
3D supported mode manually
Signal
Resolution
Horizontal
Frequency (kHz)
Verticla
Frequency
(Hz)
DTV
HD / SD
-
-
ATV(CVBS)
SD
-
-
Component
HD / SD
-
-
1024 x 768
48.36
1360 x 768
47.71
Input
60
HDMI-PC
1920 x 1080
67.5
Others
-
-
480P
31.5
60
576P
31.25
50
37.5
50
720p
2D to 3D, Side by Side(Half), Top &
Bottom, Checker Board, Frame
Sequential, Row Interleaving, Column
Interleaving
2D to 3D, Side by Side(Half), Top &
Bottom
2D to 3D, Side by Side(Half), Top &
Bottom, Checker Board, Frame
Sequential, Row Interleaving, Column
Interleaving
45
60
50
33.75
60
27
24
28.12
25
33.75
30
56.25
50
67.5
60
Under 704 x 480
-
-
2D to 3D
Over 704 x 480
interlaced
-
-
2D to 3D, Side by Side(Half), Top &
Bottom
-
50 / 60
2D to 3D, Side by Side(Half), Top &
Bottom,Checker Board, Frame
Sequential, Row Interleaving, Column
Interleaving
-
others
2D to 3D, Side by Side(Half), Top &
Bottom,Checker Board, Row
Interleaving, Column Interleaving
Under 320 x 240
-
-
2D to 3D
Over 320 x 240
-
-
2D to 3D, Side by Side(Half), Top &
Bottom
1024 x 768p
-
30 / 60
1280 x 720p
-
30 / 60
1920 x 1080p
-
30 / 60
Others
-
-
HDMI-DTV
ENGLISH
1080p
USB ,DLNA
(Movie)
Over 704 x 480
progressive
Miracast/Widi
2D to 3D, Side by Side(Half), Top &
Bottom
28.12
1080i
USB, DLNA
(Photo)
Playable 3D video format
2D to 3D, Side by Sied(Half), Top &
Bottom
2D to 3D, Side by Side(Half), Top &
Bottom,Checker Board, Row
Interleaving, Column Interleaving
2D to 3D, Side by Side(Half), Top &
Bottom, Checker Board, Frame
Sequential, Row Interleaving, Column
Interleaving
2D to 3D, Side by Side(Half), Top &
Bottom
2D to 3D
SPECIFICATIONS / external control device setup
41
yyVideo, which is input as below media contents is switched into the 3D screen automatically.
3D supported mode automatically
Input
Signal
640 x 480
Horizontal
Frequency (kHz)
576p
Playable 3D video format
Top & Bottom,
Side by Side(Half), Side by Side(Full)
31.469 / 31.5
62.938 / 63
480p
Vertical
Frequency (Hz)
59.94 / 60
Frame Packing, Line Alternative
31.469 / 31.5
Top & Bottom,
Side by Side(Half), Side by Side(Full)
62.938 / 63
Frame Packing, Line Alternative
31.25
50
Top & Bottom,
Side by Side(Half), Side by Side(Full)
62.5
720p
HDMI
1080i
37.50
50
44.96 / 45
59.94 / 60
75
50
89.91 / 90
59.94 / 60
28.125
50
33.72 / 33.75
59.94 / 60
56.25
50
67.432 / 67.5
59.94 / 60
26.97 / 27
23.97 / 24
28.125
25
33.716 / 33.75
29.976 / 30
43.94 / 54
23.97 / 24
56.25
25
67.432 / 67.5
29.976 / 30
56.25
50
67.432 / 67.5
59.94 / 60
USB
1080p
33.75
30
DLNA
1080p
33.75
30
Top & Bottom,
Side by Side(Half), Side by Side(Full)
Frame Packing, Line Alternative
Top & Bottom,
Side by Side(Half), Side by Side(Full)
Frame Packing, Field Alternative
Top & Bottom,
Side by Side(Half), Side by Side(Full)
Frame Packing, Line Alternative
Top & Bottom, Side by Side(Half)
Side by Side(Half), Top & Bottom,
Checker Board, MPO(Photo), JPS(Photo)
external control device setup
To obtain the external control device setup information, please visit ‘www.lg.com’.
ENGLISH
1080p
Frame Packing, Line Alternative
42
MAINTENANCE / TROUBLESHOOTING
MAINTENANCE
Cleaning Your TV
Clean your TV regularly to keep it at peak performance and to extend the product lifespan.
CAUTION
yyMake sure to turn the power off and disconnect the power cord and all other cables first.
yyWhen the TV is left unattended or unused for a long time, disconnect the power cord from the wall outlet to
prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe
immediately with a dry cloth.
CAUTION
yyDo not push, rub, or hit the surface with your fingernail or a sharp object, as this may result in scratches on the
screen and image distortions.
yyDo not use any chemicals, such as waxes, benzene, alcohol, thinners, insecticides, air fresheners, lubricants, as
these may damage the screen’s finish and cause discoloration.
yyDo not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
ENGLISH
TROUBLESHOOTING
Problem
Solution
Cannot control the TV with the
remote control.
yyCheck the remote control sensor on the product and try again.
yyCheck if there is any obstacle between the product and the remote control.
to
yyCheck if the batteries are still working and properly installed ( to ,
No image display and no sound is
produced.
yyCheck if the product is turned on.
yyCheck if the power cord is connected to a wall outlet.
yyCheck if there is a problem in the wall outlet by connecting other products.
The TV turns off suddenly.
yyCheck the power control settings. The power supply may be interrupted.
yyCheck if the Auto sleep feature is activated in the Time settings.
yyIf there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of
inactivity.
).
The model and serial number of the TV is located
on the back and one side of the TV.
Record it below should you ever need service.
MODEL
SERIAL
Download PDF