Samsung | PS-42P4A1 | Samsung PS-42P4A1 Quick Guide

BN68-00682A-00Eng_0529
10/21/04
2:38 PM
Page 8
Infrared Remote Control
ENG
TURNS THE PDP ON AND OFF
WHEN YOU PRESS A BUTTON , ‘
’
APPEARS ALONG WITH SELECTED MODE
(TV, VCR, CATV, DVD OR STB) AND
BATTERY STATUS ON LCD
PICTURE EFFECT SELECTION
SOUND EFFECT SELECTION
TELETEXT CANCEL
MAKE THE REMOTE CONTROL WORKS
FOR TV, VCR, CATV, DVD PLAYER, STB
DIRECT CHANNEL SELECTION
AUTOMATIC SWITCH-OFF/
TELETEXT SUB-PAGE
PICTURE SIZE/
TELETEXT SIZE SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
NEXT CHANNEL/
TELETEXT NEXT PAGE/
TELEWEB FORWARD
EXTERNAL INPUT SELECTION/
TELETEXT PAGE HOLD
VOLUME DECREASE
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE/
TELEWEB BACKWARD
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
MENU DISPLAY/
TELETEXT INDEX
INFORMATION DISPLAY/
TELETEXT REVEAL
TV MODE SELECTION
EXIT TELETEXT
EXIT TELEWEB
(DEPENDING ON THE MODEL)
MOVE TO THE REQUIRED
MENU OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
PICTURE STILL
TELEWEB DISPLAY
(DEPENDING ON THE MODEL)
FASTEXT TOPIC SELECTION
REMOTE CONTROL SETUP
IF YOUR REMOTE CONTROL IS NOT
FUNCTIONING PROPERLY, TAKE
OUT THE BATTERIES AND PRESS
THE RESET BUTTON FOR ABOUT
2~3 SECONDS. RE-INSERT THE
BATTERIES AND TRY USING THE
REMOTE CONTROL AGAIN.
➢
CONFIRM YOUR CHOICE
(STORE OR ENTER)
SOUND MODE SELECTION
TruSurround XT
MODE SELECTION
PIP FUNCTIONS;
- PIP ACTIVATING OR DEACTIVATING
(PIP ON)
- SWAPPING THE MAIN AND THE SUB
PICTURE (SWAP)
- LOCATION SELECTION (POSITION)
- SOURCE SELECTION (SOURCE)
- SIZE SELECTION (SIZE)
- SCAN
- SELECTING THE CHANNEL OF SUB
PICTURE (P
)
VCR/DVD FUNCTIONS;
- REWIND (REW)
- STOP
- PLAY/PAUSE
- FAST FORWARD (FF)
The performance of the remote control may be affected by bright light.
BN68-00682A-00Eng_0529
10/21/04
2:39 PM
Page 56
Connecting to the S-Video Input
ENG
The S-VIDEO1 and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the TV
①
and
Camcorder
Side of the TV
①
VCR
and
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
☛
Whenever you connect an audio or video system to your television,
ensure that all elements are switched off. Refer to the documentation
supplied with your equipment for detailed connection instructions
and associated safety precautions.
BN68-00682A-00Eng_0529
10/21/04
2:39 PM
Page 57
Connecting to the DVI Input
ENG
The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output.
Rear of the TV
Personal Computer
and
Connecting to the PC Input
The “RGB” (video) and “AUDIO” connectors are used for interfacing with your PC.
Rear of the TV
Personal Computer
and
BN68-00682A-00Eng_0529
10/21/04
2:39 PM
Page 58
Connecting to the Component Input
ENG
Rear of the TV
① The “COMPONENT 1” connectors are
①
DVD
②
DTV receiver
used for equipment with a DVD output.
(480i,p/576i,p/720p/1080i)
② The “COMPONENT 2” connectors are
used for DTV receiver. (480i,p/576i,p/
720p/1080i)
BN68-00682A-00Eng_0529
10/21/04
2:39 PM
Page 59
Connecting and Using the Home Theater System
ENG
Use the Monitor Out ports of the PDP for Home Theater System Connections.
Rear of the TV
Connecting the Home Theater System
① Connect the monitoring audio out L, and
R jacks of the MONITOR OUT on the
rear-side connection panel of the PDP
TV to the AUDIO IN jacks of the DVD
Home Theater System (or AV Receiver)
using the audio cable.
② Press the SOURCE button to select the
desired external device connected to the
PDP TV.
③ If you want to hear the sound through
separate speakers, cancel the internal
amplifier.
②
①
DVD Home Theater
☛
AV Receiver Amplifier
◆ Refer to corresponding user’s manual from the manufacturer for wiring the
speakers to the DVD Home Theater System (or AV Receiver).
◆ Disable the PDP TV internal speaker to enjoy the rich sound through the
speakers of your Home Theater System.
◆ In this case, enjoy the sound from the Home Theater System while the PDP TV
does not produce the audio.
To Display the DVD Home Theater
! Turn the PDP on and press the SOURCE button to select the Ext.1 (Ext.2 or Ext.3).
@ Be sure to connect the video cable properly if desired external input (Ext.1 (Ext.2 or Ext.3))
cannot be selected.
# Play the DVD after activating the DVD Home Theater System.
$ Use the volume control of the Home Theater System while watching the PDP using the DVD
Home Theater, where the PDP TV does not produce the audio.
Download PDF